Chief JWDIWVB flat panel wall mount

INSTALLATION INSTRUCTIONS
Medium Flat Panel In-Wall Swing Arm Mount
JWDIW Series
JWDIW Series
Installation Instructions
DISCLAIMER
Milestone AV Technologies, Inc., and its affiliated corporations
and subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® and Centris™ are trademarks of Milestone AV
Technologies, Inc. All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to this accessory does not exceed
75 lbs (34 kg).
LEGEND
2
Tighten Fastener
Hex-Head Wrench
Apretar elemento de fijación
Llave de cabeza hexagonal
Befestigungsteil festziehen
Sechskantschlüssel
Apertar fixador
Chave de cabeça sextavada
Serrare il fissaggio
Chiave esagonale
Bevestiging vastdraaien
Zeskantsleutel
Serrez les fixations
Clé à tête hexagonale
Loosen Fastener
Phillips Screwdriver
Aflojar elemento de fijación
Destornillador Phillips
Befestigungsteil lösen
Kreuzschlitzschraubendreher
Desapertar fixador
Chave de fendas Phillips
Allentare il fissaggio
Cacciavite a stella
Bevestiging losdraaien
Kruiskopschroevendraaier
Desserrez les fixations
Tournevis à pointe cruciforme
Installation Instructions
JWDIW Series
TOOLS REQUIRED FOR INSTALLATION AND PARTS
3/16"
(Included)
7/32"
(Included)
B (4)
A (1)
I/M
x1
Interface Bracket
Kit
J (4)
8-32 x 1/2"
H (2)
G (2)
E (4)
1/4"
D (4)
5/16"
C (4)
5/16-18 x 5/8"
F (1)
K (4)
(including hardware)
x1
R (4)
L (12)
M (4)
N (2)
08 x 1/2"
P (1)
3/16"
Q (1)
7/32""
3
JWDIW Series
Installation Instructions
Installation
5.
The following procedure assumes that a Chief Listed Model
MAC501 In-Wall accessory has previously been installed
following the installation instructions provided by the
manufacturer. If a MAC501 is not installed or there are any
other questions regarding the installation of this accessory,
immediately contact a Chief Customer Service representative.
Align four mounting holes in swing arm mounting bracket
with four mounting holes in MAC501. (See Figure 2)
Swing Arm
Mounting
Bracket
WARNING: IMPROPER INSTALLATION CAN LEAD TO
5
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! DO NOT deviate from
installation instructions provided. DO NOT substitute
hardware.
The MAC501 is designed to accommodate 4-1/2" of right or left
display offset. This is accomplished by aligning the JWDIW with
either the right hand or left hand hole in the MAC501 bottom
support plate. The bumper mounting bracket is installed on the
side opposite the side used for installing the JWDIW swing arm.
(See Figure 2)
3
4
Install Bumper
1.
Install two bumpers (G) to bumper mounting bracket (F).
(See Figure 1)
Lower Support Plate
NOTE: A screwdriver may be required to push bumper into
hole in bumper mounting bracket.
2.
Secure bumper mounting bracket (F) to MAC501 on
whichever side the arm is going to be retracted, using two
Phillips pan head screws (N). (See Figure 1)
1
Secure on
either side
Figure 2
6.
Secure swing arm to MAC501 using four button head cap
screws (C), four lock washers (D) and four flat washers (E).
(See Figure 3)
7.
Cover remaining four openings in back of MAC501 with four
screw covers (K). (See Figure 3)
(F) x 1
(G) x 2
(K) x 4
Secure
on either
side
6
2
(N) x 2
(E) x 4
(D) x 4
(C) x 4
Figure 1
3.
Align bottom of swing arm pivot pin with hole in lower
support plate. (See Figure 2)
4.
Lower swing arm until pivot pin rests in hole in lower support
plate. (See Figure 2)
4
Figure 3
Installation Instructions
JWDIW Series
5.
Display Installation
Route cables and wires to display.
NOTE: If the display being installed has a 100x100 VESA
mounting pattern, no interface bracket is required and
the display can be mounted directly to the Centris cup
as outlined below.
NOTE: If the display being installed requires an interface
2
bracket, refer to the interface bracket installation
instructions.
3
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
Ensure that screws are not too long.
4
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread
engagement in display may cause display to fall! Back out
screws ONLY as necessary to allow installation of Centris
cup!
1.
Start two M4 x 8mm Phillips pan head screws (included in
hardware kit) into upper mounting holes in display back.
(See Figure 4)
NOTE: Leave at least 1/8" of each screw protruding out back
of display.
x2
Figure 5
Cable Management
1.
Attach all cables to display.
2.
If necessary, use cable tie mounts (M) and cable ties (R) to
secure cables within MAC501.
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched by
installation of cover (H) or screws (J).
1
x2
3.
Carefully insert cables in cavity located in lower portion of
mount arm (See Figure 6).
4.
Using Phillips screwdriver, install cover (H) with two screws
(J). (See Figure 6)
2
Cable Path
(typical)
Figure 4
2.
Align two screws in display back with upper mounting holes
in Centris cup and lower display until screws are seated in
lower area of teardrop mounting holes. (See Figure 5)
3.
Install two more of the same screws through lower mounting
holes in Centris cup and into display back. (See Figure 5)
4.
Tighten all hardware.
(H) x 2
3
(J) x 4
Figure 6
5
JWDIW Series
Installation Instructions
Optional Trim Installation
1.
Remove paper covering adhesive from tape squares (L)
and affix three tape squares to inside lower flange of each
trim piece (B). (See Figure 7)
2.
Orient trim pieces (B).
3.
Remove paper covering adhesive back from tape squares
(L) on trim and press trim (B) against inner wall of box.
(See Figure 7)
2
(See Figure 7)
1
2
3
Figure 8
(B) x 4
(L) x 12
DISPLAY ROLL, PITCH, YAW Tension
1.
Disconnect all wires and cable from the display.
2.
Remove two Lower screws securing display to Centris cup.
ADJUSTMENTS
3.
Loosen two Upper screws securing display.
PIVOT / SWING ARM Tension
4.
Lift display upward and away from mount.
1.
Using 3/16" hex key (P), slightly loosen or tighten the pivot/
swing tension adjustment screw(s) as necessary (See
Figure 8).
5.
Using 3/16" hex key (P), turn the tension adjustment screw
clockwise to increase tension, or counter-clockwise to
decrease tension. (See Figure 9)
2.
Using 7/32" hex key (Q), slightly loosen or tighten the
adjustment screw at end of swing arm. (See Figure 8)
6.
Re-install display.
Figure 7
5
Figure 9
6
Installation Instructions
JWDIW Series
7
JWDIW Series
Installation Instructions
USA/International
Chief Manufacturing, a products division
of Milestone AV Technologies
8805-000241 RevC
2009 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
11/09
Europe
Asia Pacific
A
P
F
A
P
F
A
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477