cover 2008.8.12 3:44 PM 페이지 2
OPERATING INSTRUCTIONS
RX-4503
AM/FM STEREO RECEIVER
RX-4503(A) 2008.8.12 3:43 PM 페이지 3
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other.
A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of
the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
PORTABLE CART WARNING
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus have been
exposed to rain or moisture, does not operate normally,
or has been dropped.
3
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
RX-4503(A) 2008.8.12 3:43 PM 페이지 4
Introduction
ENGLISH
READ THIS BEFORE OPERATING YOUR UNIT
CAUTION :
This symbol is intended to alert the user to the presence
of uninsulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol is intended to alert the user to the presence
of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Caution regarding installation
Note : For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure.
Do not block ventilation openings or stack other equipment on the top.
Note to CATV System Installer :
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point
of cable entry as practical.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du Canada.
FOR YOUR SAFETY
U.S.A
CANADA
CAUTION
• Leave a space around the unit for sufficient ventilation.
• Avoid installation in extremely hot or cold locations, or in an area
that is exposed to direct sunlight or heating equipment.
• Keep the unit free from moisture, water, and dust.
• Do not let foreign objects in the unit.
• The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, table-cloths, curtains, etc.
• No naked flame sources, such as lighted candles, should be placed
on the unit.
• Please be care the environmental aspects of battery disposal.
• The unit shall not be exposed to dripping or splashing for use.
• No objects filled with liquids, such as vases, shall be placed on the
unit.
• Do not let insecticides, benzene, and thinner come in contact with
the set.
• Never disassemble or modify the unit in any way.
■Notes on the AC power cord and the wall outlet.
• The unit is not disconnected from the AC power source(mains) as
long as it is connected to the wall outlet, even if the unit has been
turned off.
• To completely disconnect this product from the mains, disconnect
the plug from the wall socket outlet.
• When setting up this product, make sure that the AC outlet you are
using is easily acceptable.
• Disconnect the plug from the wall outlet when not using the unit for
long periods of time.
120 V
Units shipped to the U.S.A and CANADA are designed for operation
on 120 V AC only.
Safety precaution with use of a polarized AC plug.
However, some products may be supplied with a nonpolarized plug.
CAUTION
: To prevent electric shock, match wide blade of
plug to wide slot, fully insert.
ATTENTION
: Pour éviter chocs électriques, introduire la lame
la plus large de la fiche dans la borne
correspondante de la prise et pousser jusqu’ au
fond.
ENERGY STARⓇ is a U.S. registered mark. As an
ENERGY STARⓇ Partner, Sherwood has
determined that this product meets the ENERGY
STARⓇ guidelines for energy efficiency.
4
RX-4503(A) 2008.8.12 3:43 PM 페이지 5
CONTENTS
Introduction
• READ THIS BEFORE OPERATING YOUR UNIT ................................................................................................................. 4
System Connections ......................................................................................................................................................... 6
Front Panel Controls ......................................................................................................................................................... 9
Remote Controls ............................................................................................................................................................... 11
• REMOTE CONTROL OPERATION RANGE ....................................................................................................................... 12
• LOADING BATTERIES ....................................................................................................................................................... 12
Operations
• LISTENING TO A PROGRAM SOURCE ............................................................................................................................ 13
• LISTENING TO RADIO BROADCASTS ............................................................................................................................. 17
• RECORDING ....................................................................................................................................................................... 19
• OTHER FUNCTIONS .......................................................................................................................................................... 19
Troubleshooting Guide ................................................................................................................................................... 20
Specifications .................................................................................................................................................................... 21
5
ENGLISH
• IMPORTANT SAFETY INSTRUCTIONS .............................................................................................................................. 3
RX-4503(A) 2008.8.12 3:43 PM 페이지 6
System Connections
ENGLISH
• Do not plug the AC input cord into the wall AC outlet until all connections are completed.
• Be sure to observe the color coding when connecting audio, video and speaker cords.
• Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver.
1. CONNECTING ANTENNAS
• Change the position of the FM indoor antenna until you
get the best reception of your favorite FM stations.
• A 75Ω outdoor FM antenna may be used to further
improve the reception. Disconnect the indoor
antenna before replacing it with the outdoor one.
• Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC
input cord and set it to a direction for the best reception.
• If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of
the AM loop antenna.
6
RX-4503(A) 2008.8.12 3:43 PM 페이지 7
2.
CONNECTING AUDIO COMPONENTS
ENGLISH
• The TAPE IN/OUT jacks can be connected to audio recording equipment such as a tape deck, an MD recorder, etc.
• The AUX IN jacks can be connected to an additional components such as CD player, a tape deck, etc.
3.
CONNECTING EXTERNAL INs
• Use these jacks to connect the corresponding analog
outputs of 6 CH decoder or DVD player with 6 CH output
for Dolby Digital or DTS, etc.
(For details, see the operator's manual of the component
to be connected.)
7
RX-4503(A) 2008.8.12 3:43 PM 페이지 8
4. CONNECTING SUBWOOFER PRE OUT
ENGLISH
• To emphasize the deep bass sounds, connect a powered
subwoofer.
5. CONNECTING SPEAKERS
• Usally SPEAKER A terminals are used for only a pair of
speakers. When you have another pair of speakers,
SPEAKER B terminals can be used.
• Be sure to connect speakers firmly and correctly according to
the channel(left and right) and the polarity(+ and -). If the
connections are faulty, no sound will be heard from the
speakers, and if the polarity of the speaker connection is
incorrect, the sound will be unnatural and lack bass.
Notes :
• For safe amplifier operation, use the speakers with
impedance of over 8Ω when you use only SPEAKER A or B
terminals and use the speakers with impedance of over 16Ω
when you use both SPEAKER A and B terminals.
• Do not let the bare speaker wires touch each other or any
metal part of this unit. This could damage this unit and/or the
speakers.
6. AC INPUT CORD
• Plug the cord into a wall AC outlet.
8
RX-4503(A) 2008.8.12 3:43 PM 페이지 9
ENGLISH
Front Panel Controls
12. MUTE button/indicator
13. SPEAKER A, B SELECTRO buttons
14. TONE DIRECT button
15. BASS UP/DOWN (▶/◀) buttons
16. TREBLE UP/DOWN (▶/◀) buttons
17. CHANNEL LEVEL UP/DOWN (▲/▼) buttons
18. CHANNEL LEVEL button
19. MEMORY button
20. FRONT AUX IN jack
For details, see next page.
21. Bluetooth IN connector
1. POWER switch
2. POWER ON/STANDBY button
3. STANDBY indicator
4. FLUORESCENT DISPLAY
For details, see below.
5. INPUT SELECTOR knob
6. SOUND button
7. BAND button
8. TUNING UP/DOWN (▲/▼) buttons
9. PRESET UP/DOWN (▲/▼) buttons
10. MASTER VOLUME CONTROL knob
11. HEADPHONE jack
FLUORESCENT DISPLAY
1. Input, frequency, volume level, operating information, etc.
2. Sound mode indicators
3. DIRECT indicator
4. Preset number, sleep time display
5. MEMORY indicator
9
6. PRESET indicator
7. SLEEP indicator
8. TUNED indicator
9. STEREO indicator
RX-4503(A) 2008.8.12 3:43 PM 페이지 10
FRONT AUX IN JACK
ENGLISH
• The FRONT AUX IN jack can be connected to additional audio components such as an MP3 player, etc.
Notes :
• When connecting this jack to an MP3 player, etc., you should use the stereo mini cord, not a mono mini cord.
• When not using the FRONT AUX IN jack and the Bluetooth IN connector, cover these with the supplied cap.
Bluetooth IN CONNECTOR
• If the Bluetooth IN connector is connected to Sherwood Audio Receiver
BT-R7(sold separately) with Bluetooth wireless technology, you can
enjoy music wirelessly with a music player featuring Bluetooth wireless
technology such as MP3 player, mobile phone, etc..
(For information on Sherwood Audio Receiver BT-R7, contact your
dealer.)
• The Bluetooth word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Sherwood
Corporation is under license. Other trademarks and trade names are
those of their respective owners.
Note :
• For safe operation, turn the power off before connecting or
disconnecting the Audio Receiver BT-R7.
10
RX-4503(A) 2008.8.12 3:43 PM 페이지 11
ENGLISH
Remote Controls
11
RX-4503(A) 2008.8.12 3:43 PM 페이지 12
ENGLISH
REMOTE CONTROL OPERATION RANGE
• Use the remote control unit within a range of about 7 meters (23
feet) and angles of up to 30 degrees aiming at the remote sensor.
LOADING BATTERIES
1. Remove the cover.
2. Load two batteries ("AAA" size, 1.5 V) matching the
polarity.
• Remove the batteries when they are not used for a
long time.
• Do not use the rechargeable batteries (Ni-Cd type).
12
RX-4503(A) 2008.8.12 3:43 PM 페이지 13
Operations
Before operation
• Push the POWER switch.
• This unit enters the standby mode and the STANDBY
indicator lights up. This means that the receiver is not
disconnected from the AC mains and a small amount of
current is retained to support the operation readiness.
• To switch the power off, push the POWER switch again.
Then the power is cut off and the STANDBY indicator
goes off.
1. In the standby mode, turn the power on.
• Each time the POWER ON/STANDBY button on the front
panel is pressed, the receiver is turned on to enter the
operating mode or off to enter the standby mode.
• On the remote control, press the POWER ON button to
enter the operating mode or press the STANDBY button to
enter the standby mode.
• In the standby mode, if the INPUT SELECTOR button on
the remote control is pressed, the receiver is turned on
automatically and the desired input is selected.
POWER
or
2. Switch the desired speakers on.
• Then the corresponding speaker indication ("SPK A or B")
is displayed and the sound can be heard from the
speakers connected to the selected speaker terminals.
• When using the headphones for private listening, press
the corresponding SPEAKER button to switch off both A
and B speakers.
3. Select the desired input source.
• Each time the INPUT SELECTOR knob is rotated, the
input source changes as follows :
→ TUNER ↔ CD ↔ TAPE ↔ AUX ←
• When selecting the EXTERNAL IN, 6 seperate analog
signals from the component connected to this input pass
through the tone and volume circuits only and can be
heard from your speakers.
• These analog signals can be heard only, not recorded.
(Frequency display)
→
EXT IN
↔
BT IN
↔
F AUX
←
• Each time the BAND button or the TUNER button is
pressed, the band changes as follows:
→ FM ST → FM MONO → AM
13
ENGLISH
LISTENING TO A PROGRAM SOURCE
RX-4503(A) 2008.8.12 3:43 PM 페이지 14
ENGLISH
4. Operate the selected component for
playback.
5. Adjust the (overall) volume.
6. To mute the sound.
• Then the MUTE indicator will flicker.
• To resume the previous sound level, press it again.
or
7. To listen with the headphones.
• Be sure to switch off both A and B speakers.
Note :
• Be careful not to set the volume too high when using
headphones.
14
RX-4503(A) 2008.8.12 3:43 PM 페이지 15
Selecting a surround sound mode
(DOLBY VS REF
DOLBY VS WIDE) or <DOLBY HP>
STEREO or 2CH DOWNMIX
( ) : Possible only when listening via the speakers.
< > : Possible only when listening via the headphones.
: Possible only when selecting the EXTERNAL IN as an input source.
• On the remote control, press the "
" button or
the STEREO button depending on whether listening in a
surround mode or in the stereo mode.
Surround sound modes
• Dolby Virtual Speaker
This mode creates a virtual surround sound field using as few as two front speakers and subwoofer, allowing you to
experience listening from 5.1 channel speakers.
* Dolby Virtual Speaker Reference("DOLBY VS REF")
The width of the front sound image is defined by the actual distance between front speakers.
* Dolby Virtual Speaker Wide("DOLBY VS WIDE")
The width of the front sound image seems to extend beyond the front speakers.
• Dolby Headphone("DOLBY HP")
This mode simulates 5.1 channel surround sound, which allows you to enjoy 5.1 channel surround sound through 2 channel
headphones, just like listening from 5.1 channel speakers.
Dolby and the double-D symbol are registered trademarks of Dolby Laboratories.
2CH downmix mode
• This mode allows the multi-channel signals from the EXTERNAL INs to be mixed down into two front channels and to be
reproduced through front speakers or headphones.
Adjusting the channel level
1. Select the desired channel.
• Each time this button is pressed, the channel is
selected as follows:
→ FL
(Front L)
→
FR ( → SW )
(Front R)
(Subwoofer)
( ) : Possible only when listening via the speakers.
• When the channel display disappears, press this button
again.
2. At each channel, adjust the level as desired.
• The channel levels can be adjusted within the range of -15
~ +15 dB.
• In general, we recommend the level to be adjusted to 0 dB.
3. Repeat the above steps 1 and 2 to adjust each channel level.
15
ENGLISH
• Each time this button is pressed, the mode changes as
follows :
RX-4503(A) 2008.8.12 3:43 PM 페이지 16
Adjusting the tone (bass and treble)
1. Select the desired tone mode.
ENGLISH
• Each time this button is pressed, the tone mode is
selected as follows :
OFF : To listen to a program source without the tone effect.
("DIR" indicator lights up.)
ON : To adjust the tone for your taste.
("DIR" indicator goes off.)
Note :
• When the EXTERNAL IN is selected as an input source,
the TONE cannot be set to ON.
When the TONE is set to ON to adjust the tone (bass and treble).
2. Adjust the tone (treble and bass) as desired.
• The tone level can be adjusted within the range of -12 ~
+12.
Notes :
• Extreme settings at high volume may damage your
speakers.
• In general, the bass and treble levels are adjusted to 0.
16
RX-4503(A) 2008.8.12 3:43 PM 페이지 17
LISTENING TO RADIO BROADCASTS
1. Select the desired band.
• Each time this button is pressed, the band changes as
follows ;
→ FM ST → FM MONO → AM
("ST" lights up)
("ST" goes off)
• When FM stereo broadcasts are poor because of weak
broadcast signals, select the FM mono mode to reduce
the noise, then FM broadcasts are reproduced in
monaural sound.
2. Press the TUNING UP/DOWN buttons for more than 0.5 second.
• The tuner will now search until a station of sufficient
strength has been found. The display shows the tuned
frequency and "TUNE".
• If the station found is not the desired one, simply repeat
this operation.
• Weak stations are skipped during auto tuning.
Manual tuning
• Manual tuning is useful when you already know the frequency of the desired station.
• After selecting the desired band, press the TUNING UP/ DOWN buttons repeatedly until the right frequency has been reached.
Auto presetting
• Auto presetting function automatically searches for FM stations only and store them in the memory.
• While listening to FM radio broadcasts, press and hold down the MEMORY button for more than 2 seconds.
• Then "AUTO MEM" flickers and this receiver starts auto
presetting.
• To stop auto presetting, press this button again.
• Up to 30 FM stations can be stored.
Notes:
• FM stations of weak strength cannot be memorized.
• To memorize AM stations or weak stations, preform
"Manual presetting" procedure with using "Manual tuning"
operation.
17
ENGLISH
Auto tuning
RX-4503(A) 2008.8.12 3:43 PM 페이지 18
Manual presetting
• You can store up to 30 preferred stations in the memory.
ENGLISH
1. Tune in the desired station with auto or manual tuning.
2. Press the MEMORY button.
• "MEM" is flickering for several seconds.
MEM
3. Select the desired preset number (1~30) and press the MEMORY button.
• When using the NUMERIC buttons on the remote control.
Examples) For “3” :
For “15” :
For “30” :
• The station has now been stored in the memory.
• When using the NUMERIC buttons, the station is stored
automatically without pressing the MEMORY button.
• A stored frequency is erased from the memory by storing
another frequency in its place.
• If “MEM” goes off, start again from the above step 2.
4. Repeat the above steps1 to 3 to memorize other stations.
MEMORY BACKUP FUNCTION
The following items, set before the receiver is turned off, are memorized.
• INPUT SELECTOR settings
• Surround mode settings
• Preset stations,etc.
Tuning to preset stations
• After selecting the tuner as an input source, select the desired preset number.
• When using the NUMERIC buttons on the remote control.
Examples) For “3” :
For “15” :
For “30” :
18
RX-4503(A) 2008.8.12 3:43 PM 페이지 19
RECORDING
• The analog signals from the EXTERNAL INs can be heard but cannot be recorded.
• The volume and tone (bass, treble) settings have no effect on the recording signals.
ENGLISH
Recording with TAPE
1. Select the desired input as a recording source except for TAPE.
2. Start recording on the TAPE.
3. Start play on the desired input.
OTHER FUNCTIONS
Operating the sleep timer
• The sleep timer allows the system to continue to operate for a specified period of time before automatically shutting off.
• To set the receiver to automatically turn off after the specified period of time.
• Each time this button is pressed, the sleep time changes
as follows:
→ 10 → 20 → 30 → --- → 90 → OFF
Unit : minutes
• While operating the sleep timer, "
" lights up.
• When the sleep time is selected, the fluorescent display
is dimly lit.
Adjusting the brightness of the fluorescent display
• Each time this button is pressed, the brightness of
the fluorescent display changes as follows:
→ ON → dimmer → OFF
• In the display OFF mode, pressing any button will
restore the display ON mode.
19
RX-4503(A) 2008.8.12 3:43 PM 페이지 20
ENGLISH
Troubleshooting Guide
If a fault occurs, run through the table below before taking your receiver for repair.
If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation,
consult with your dealer. Under no circumstances should you repair the receiver yourself as this could invalidate
the warranty.
PROBLEM
POSSIBLE CAUSE
REMEDY
No power
• The AC input cord is disconnected.
• Poor connection at AC wall outlet or the
outlet is inactive.
• Connect the cord securely.
• Check the outlet using a lamp or another
appliance.
No sound
• The speaker cords are disconnected.
• The volume is adjusted too low.
• The MUTE button is pressed to ON.
• Check the speaker connections.
• Adjust the volume.
• Press the MUTE button to cancel the
muting effect.
• Press the SPEAKER A or B button to ON.
• Select the desired input source correctly.
• Make connections correctly.
• Speakers are not switched on.
• Incorrect selection of the input source.
• Incorrect connections between the
components.
• No antenna is connected.
• The desired station frequency is not tuned
in.
• The antenna is in wrong position.
• Connect an antenna.
• Tune in the desired station frequency.
• An incorrect station frequency has been
memorized.
• The memorized stations are cleared.
• Memorize the correct station frequency.
Poor FM reception
• No antenna is connected.
• The antenna is not positioned for the best
reception.
• Connect an antenna.
• Change the position of the antenna.
Continuous hissing noise
during FM reception,
especially when a stereo
broadcast is received.
• Weak signals.
• Change the position of the antenna.
• Install an outdoor antenna.
Continuous or intermittent
hissing noise during AM
reception, especially at
night.
• Noise is caused by motors, fluorescent
lamps or lightning, etc.
• Keep the receiver away from noise
sources.
• Install an outdoor AM antenna.
No recording
• Incorrect selection between the
components.
• Incorrect operation of each component for
playback and recording.
• Make connections correctly.
• Batteries are not loaded or exhausted.
• The remote sensor is obstructed.
• Replace the batteries.
• Remove the obstacle.
Stations cannot be
received
Preset stations cannot be
received
Remote control unit does
not operate.
20
• Move the antenna and retry tuning.
• Memorize the stations again.
• Operate each component correctly.
RX-4503(A) 2008.8.12 3:43 PM 페이지 21
Specifications
•Power output, stereo mode, 8 Ω, THD 0.08 %, 40 Hz~20 kHz ............................................................... 2X100 W
•Total harmonic distortion, 8 Ω, 100 W, 40 Hz~20 kHz ............................................................................... 0.02 %
•Intermodulation distortion
60 Hz : 7 kHz= 4 : 1 SMPTE, 8 Ω, 100 W .................................................................................................. 0.02 %
•Input sensitivity, 47 kΩ
Line(CD,TAPE,AUX) ................................................................................................................................. 200 mV
•Signal to noise ratio, IHF “A” weighted
Line(CD,TAPE,AUX) .................................................................................................................................... 96 dB
•Frequency response
Line(CD,TAPE,AUX), 10 Hz~95 kHz .......................................................................................................... -3 dB
•Output level
TAPE OUT, 2.2 kΩ ................................................................................................................................... 200 mV
•Bass/Treble control, 100 Hz/10 kHz ......................................................................................................... ±12 dB
FM TUNER SECTION
•Tuning frequency range ................................................................................................................. 87.5~108 MHz
•Usable sensitivity, THD 3%, S/N 30 dB ................................................................................................. 16.25 dBf
•50 dB quieting sensitivity, mono/stereo ............................................................................................ 25.2/45.2 dBf
•Signal to noise ratio, 65 dBf, mono/stereo .............................................................................................. 67/66 dB
•Total harmonic distortion, 65 dBf, 1 kHz, mono/stereo ........................................................................... 0.6/0.7%
•Frequency response, 20 Hz~14 kHz ........................................................................................................... -3 dB
•Stereo separation, 1 kHz .............................................................................................................................. 35 dB
•Capture ratio .................................................................................................................................................. 4 dB
•IF rejection ratio ......................................................................................................................................... 105 dB
AM TUNER SECTION
•Tuning frequency range ................................................................................................................. 520~1710 kHz
•Usable sensitivity .................................................................................................................................... 800 μV/m
•Signal to noise ratio ...................................................................................................................................... 51 dB
•Selectivity ..................................................................................................................................................... 30 dB
GENERAL
•Power supply .................................................................................................................................. 120 V~ 60 Hz
•Power consumption ........................................................................................................................................ 2.5A
•Dimensions (W×H×D, including protruding parts) ............. 440×141×365mm(17-3/8×5-1/2×14-3/8 inches)
•Weight (Net) .................................................................................................................................. 8.3 kg(18.3 lbs)
Note: Design and specifications are subject to change without notice for improvements.
21
ENGLISH
AMPLIFIER SECTION
cover 2008.8.12 3:44 PM 페이지 1
RX-4503
AM/FM STEREO RECEIVER
5707-00000-120-0S