3M CL574 equipment cleansing kit

3M MATERIAL SAFETY DATA SHEET Disinfecting Office Cleaner CL574
11/30/2007
Material Safety Data Sheet
Copyright, 2007, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: Disinfecting Office Cleaner CL574
MANUFACTURER: 3M
DIVISION: Office Supplies Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 11/30/2007
Supercedes Date: 06/13/2006
Document Group: 19-0389-7
Product Use:
Intended Use:
Specific Use:
Disinfectant
Cleaner
SECTION 2: INGREDIENTS
Ingredient
C.A.S. No.
WATER
BUTANE
2-BUTOXYETHANOL
TETRASODIUM ETHYLENEDIAMINETETRAACETATE
PROPANE
Lemon Fragrance
SODIUM HYDROXIDE
7732-18-5
106-97-8
111-76-2
64-02-8
74-98-6
Trade Secret
1310-73-2
% by Wt
88 - 93
2- 4
1- 3
1- 3
1- 3
<1
0- 1
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: White foaming liquid.
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Flammable liquid and vapor. Closed containers exposed to heat from
fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
May cause target organ effects.
_________________________________________________________________________________________________
Page 1 of 8
3M MATERIAL SAFETY DATA SHEET Disinfecting Office Cleaner CL574
11/30/2007
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Inhalation:
Intentional concentration and inhalation may be harmful or fatal.
Cardiac Sensitization: Signs/symptoms may include irregular heartbeat (arrhythmia), faintness, chest pain, and may be fatal.
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
Simple Asphyxiation: Signs/symptoms may include increased heart rate, rapid respirations, drowsiness, headache, incoordination,
altered judgement, nausea, vomiting, lethargy, seizures, coma, and may be fatal.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Blood Effects: Signs/symptoms may include generalized weakness and fatigue, skin pallor, changes in blood clotting time, internal
bleeding, and/or hemoglobinemia.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air.
If Swallowed:
Get immediate medical attention.
Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
_________________________________________________________________________________________________
Page 2 of 8
3M MATERIAL SAFETY DATA SHEET Disinfecting Office Cleaner CL574
11/30/2007
give anything by mouth to an unconscious person. Get medical attention.
4.2 NOTE TO PHYSICIANS
Exposure may increase myocardial irritability. Do not administer sympathomimetic drugs unless absolutely necessary.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
No Data Available
00 ºF [Test Method: Closed Cup] [Details: Propellent]
1.1 %
10.6 %
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Flammable liquid and vapor. Closed containers exposed to heat from fire may build
pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Refer to other sections of this MSDS for information regarding physical and health hazards,
respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information
on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up
by qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only nonsparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to
disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and
could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build
dikes to prevent entry into sewer systems or bodies of water. Cover spill area with a fire-extinguishing foam designed for use on
solvents, such as alcohols and acetone, that can dissolve in water. An AR - AFFF type foam is recommended. Working from around
the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in
sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a toxic, corrosivity or
flammability hazard. Collect as much of the spilled material as possible using non-sparking tools. Clean up residue with water.
Collect the resulting residue containing solution. Place in a metal container approved for transportation by appropriate authorities.
Seal the container. Dispose of collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
_________________________________________________________________________________________________
Page 3 of 8
3M MATERIAL SAFETY DATA SHEET Disinfecting Office Cleaner CL574
11/30/2007
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat,
sparks, open flame, pilot lights and other sources of ignition. Ground containers securely when transferring contents. Wear low static
or properly grounded shoes. No smoking while handling this material. Do not spray near flames or sources of ignition. Avoid
breathing of vapors, mists or spray. Avoid static discharge. Avoid eye contact with vapors, mists, or spray. Avoid contact with
oxidizing agents.
7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area. Keep container
tightly closed. Store away from oxidizing agents.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Provide appropriate local exhaust ventilation on open containers. Use in a well-ventilated area. Do not use in a confined area or areas
with little or no air movement. Do not remain in area where available oxygen may be reduced.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Neoprene.
8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection. Avoid
breathing of vapors, mists or spray.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Not applicable.
8.3 EXPOSURE GUIDELINES
Ingredient
2-BUTOXYETHANOL
2-BUTOXYETHANOL
2-BUTOXYETHANOL
BUTANE
BUTANE
PROPANE
PROPANE
SODIUM HYDROXIDE
SODIUM HYDROXIDE
SODIUM HYDROXIDE
SODIUM HYDROXIDE
Authority
Type
Limit
Additional Information
ACGIH
OSHA
OSHA
ACGIH
OSHA
ACGIH
OSHA
ACGIH
CMRG
OSHA
OSHA
TWA
TWA, Vacated
TWA
TWA
TWA
TWA
TWA
CEIL
TWA
CEIL
TWA
20 ppm
25 ppm
50 ppm
1000 ppm
800 ppm
1000 ppm
1000 ppm
2 mg/m3
2 mg/m3
2 mg/m3
2 mg/m3
Table A3
Skin Notation*
Skin Notation*; Table Z-1
Table Z-1A
Table Z-1
Table Z-1A
Table Z-1
_________________________________________________________________________________________________
Page 4 of 8
3M MATERIAL SAFETY DATA SHEET Disinfecting Office Cleaner CL574
11/30/2007
* Substance(s) refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye,
either by airborne or, more particularly, by direct contact with the substance. Vehicles can alter skin absorption.
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade:
General Physical Form:
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
Boiling point
Density
Vapor Density
White foaming liquid.
Liquid
No Data Available
00 ºF [Test Method: Closed Cup] [Details: Propellent]
1.1 %
10.6 %
<=343 ºF [Details: Liquid portion]
0.97 g/ml
>=1 [Ref Std: AIR=1]
Vapor Pressure
18 mmHg [@ 68 ºF]
Specific Gravity
pH
Melting point
Solubility In Water
0.97 [Ref Std: WATER=1]
7-9
Not Applicable
100 %
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Sparks and/or flames
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance
Condition
Carbon monoxide
Carbon dioxide
During Combustion
During Combustion
_________________________________________________________________________________________________
Page 5 of 8
3M MATERIAL SAFETY DATA SHEET Disinfecting Office Cleaner CL574
11/30/2007
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in a permitted hazardous waste incinerator. Combustion products will include HCl. Facility
must be capable of handling halogenated materials.
As a disposal alternative, dispose of waste product in a permitted hazardous waste facility.
Dispose of empty product containers in a sanitary landfill.
EPA Hazardous Waste Number (RCRA): D001 (Ignitable)
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
70-0712-0156-3, 70-0712-0764-4, 70-0712-2313-8, 70-0715-0649-0
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - No
Reactivity Hazard - No
Immediate Hazard - Yes
Delayed Hazard - No
_________________________________________________________________________________________________
Page 6 of 8
3M MATERIAL SAFETY DATA SHEET Disinfecting Office Cleaner CL574
11/30/2007
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient
C.A.S. No
2-BUTOXYETHANOL (GLYCOL ETHERS)
111-76-2
% by Wt
1- 3
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
Revision Changes:
Section 1: Product use information was modified.
Copyright was modified.
Section 4: First aid for inhalation - medical assistance - was modified.
Section 3: Other health effects information was modified.
Section 14: ID Number Heading Template 1 was added.
Section 14: ID Number(s) Template 1 was added.
Section 2: Ingredient table was added.
Section 15: EPCRA 313 information was added.
Section 15: EPCRA 313 text was added.
Section 8: Exposure guidelines ingredient information was added.
Section 8: Exposure guidelines legend was added.
Section 8: Exposure guideline note was added.
Section 8: Exposure guidelines data source legend was added.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
_________________________________________________________________________________________________
Page 7 of 8
3M MATERIAL SAFETY DATA SHEET Disinfecting Office Cleaner CL574
11/30/2007
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 8 of 8