3M CL600 equipment cleansing kit

MATERIAL SAFETY DATA SHEET 3M(TM) Anti-Static Electronic Equipment Cleaner, #CL600
03/13/2009
Material Safety Data Sheet
Copyright, 2009, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) Anti-Static Electronic Equipment Cleaner, #CL600
MANUFACTURER: 3M
DIVISION: Office Supplies Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 03/13/2009
Supercedes Date: 01/13/2009
Document Group: 23-8724-9
Product Use:
Intended Use:
Specific Use:
Cleaner for Office Electronic Equipment
Electronic Equipment Cleaner
SECTION 2: INGREDIENTS
Ingredient
C.A.S. No.
% by Wt
WATER
2-BUTOXYETHANOL
ISOBUTANE
AMMONIUM HYDROXIDE
7732-18-5
111-76-2
75-28-5
1336-21-6
90 - 95
3- 8
1- 5
0- 2
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Liquid in aerosol container, foamy white, slight ammonia-like odor
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Closed containers exposed to heat from fire may build pressure and
explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
May cause
target organ effects.
3.2 POTENTIAL HEALTH EFFECTS
_________________________________________________________________________________________________
Page 1 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Anti-Static Electronic Equipment Cleaner, #CL600
03/13/2009
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Inhalation:
Intentional concentration and inhalation may be harmful or fatal.
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
Single exposure, above recommended guidelines, may cause:
Cardiac Sensitization: Signs/symptoms may include irregular heartbeat (arrhythmia), faintness, chest pain, and may be fatal.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Blood Effects: Signs/symptoms may include generalized weakness and fatigue, skin pallor, changes in blood clotting time, internal
bleeding, and/or hemoglobinemia.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air.
Get immediate medical attention.
If Swallowed:
Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
_________________________________________________________________________________________________
Page 2 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Anti-Static Electronic Equipment Cleaner, #CL600
03/13/2009
4.2 NOTE TO PHYSICIANS
Exposure may increase myocardial irritability. Do not administer sympathomimetic drugs unless absolutely necessary.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
No Data Available
Not Applicable
1.1 % [Details: Propellant]
10.6 % [Details: Propellant]
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Closed containers exposed to heat from fire may build pressure and explode. Vapors may
travel long distances along the ground or floor to an ignition source and flash back. Aerosol container contains gas under pressure.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: If possible, seal leaking container. Place leaking containers in a well-ventilated area, preferably an
operating exhaust hood, or if necessary outdoors on an impermeable surface until appropriate packaging for the leaking container or
its contents is available.
Refer to other sections of this MSDS for information regarding physical and health hazards, respiratory protection, ventilation, and
personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information on handling and managing the spill.
Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Remove all
ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-sparking tools. For large spill, or spills
in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice.
Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode.
Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available
inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not
remove a toxic, corrosivity or flammability hazard. Collect as much of the spilled material as possible using non-sparking tools.
Clean up residue with detergent and water. Collect the resulting residue containing solution. Place in a metal container approved for
transportation by appropriate authorities. Seal the container. Dispose of collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
_________________________________________________________________________________________________
Page 3 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Anti-Static Electronic Equipment Cleaner, #CL600
03/13/2009
7.1 HANDLING
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat,
sparks, open flame, pilot lights and other sources of ignition. Ground containers securely when transferring contents. Wear low static
or properly grounded shoes. No smoking while handling this material. Do not spray near flames or sources of ignition. Avoid
breathing of vapors, mists or spray. Avoid static discharge. Avoid eye contact with vapors, mists, or spray. Avoid contact with
oxidizing agents.
7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container tightly closed. Store away from oxidizing
agents.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Do not use in a confined area or areas with little or no air movement. Do not remain in area where available oxygen may be reduced.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Butyl Rubber.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges. Consult the current 3M
Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Not applicable.
8.3 EXPOSURE GUIDELINES
Ingredient
2-BUTOXYETHANOL
2-BUTOXYETHANOL
2-BUTOXYETHANOL
AMMONIUM HYDROXIDE
AMMONIUM HYDROXIDE
ISOBUTANE
Authority
Type
Limit
Additional Information
ACGIH
OSHA
OSHA
CMRG
CMRG
ACGIH
TWA
TWA, Vacated
TWA
TWA, as ammonia
STEL, as ammonia
TWA
20 ppm
25 ppm
50 ppm
10 ppm
20 ppm
1000 ppm
Table A3
Skin Notation*
Skin Notation*; Table Z-1
* Substance(s) refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye,
either by airborne or, more particularly, by direct contact with the substance. Vehicles can alter skin absorption.
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatory agency.
_________________________________________________________________________________________________
Page 4 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Anti-Static Electronic Equipment Cleaner, #CL600
03/13/2009
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade:
General Physical Form:
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
Boiling point
Density
Vapor Density
Liquid in aerosol container, foamy white, slight ammonia-like odor
Liquid
No Data Available
Not Applicable
1.1 % [Details: Propellant]
10.6 % [Details: Propellant]
10 - 343 ºF
967 g/l
>=1 [Ref Std: AIR=1]
Vapor Pressure
760 mm [@ 68 ºF]
Specific Gravity
pH
Melting point
0.97 [Ref Std: WATER=1]
11.3
Not Applicable
Solubility in Water
VOC Less H2O & Exempt Solvents
Appreciable
7.9 %
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Heat
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance
Condition
Carbon monoxide
Carbon dioxide
During Combustion
During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
_________________________________________________________________________________________________
Page 5 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Anti-Static Electronic Equipment Cleaner, #CL600
03/13/2009
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Dispose of waste product in a permitted hazardous waste facility.
As a disposal alternative, Incinerate in a permitted hazardous waste incinerator. Facility must be capable of handling aerosol cans.
EPA Hazardous Waste Number (RCRA): D001 (Ignitable)
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
70-0715-0339-8
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - Yes
Reactivity Hazard - No
Immediate Hazard - Yes
Delayed Hazard - Yes
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient
C.A.S. No
2-BUTOXYETHANOL (GLYCOL ETHERS)
AMMONIUM HYDROXIDE (AMMONIA
COMPOUNDS)
111-76-2
1336-21-6
% by Wt
3- 8
0- 2
STATE REGULATIONS
Contact 3M for more information.
_________________________________________________________________________________________________
Page 6 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Anti-Static Electronic Equipment Cleaner, #CL600
03/13/2009
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 2
Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
Revision Changes:
Section 6: Release measures information was modified.
Section 13: Waste disposal method information was modified.
Section 15: 311/312 Fire Hazard score was modified.
Section 15: 311/312 Delayed Hazard score was modified.
Section 5: Flash point information was modified.
Section 9: Flash point information was modified.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
_________________________________________________________________________________________________
Page 7 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) Anti-Static Electronic Equipment Cleaner, #CL600
03/13/2009
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 8 of 8