3M 573 equipment cleansing kit

MATERIAL SAFETY DATA SHEET 3M(TM) DESK & OFFICE CLEANER 573
06/17/2008
Material Safety Data Sheet
Copyright, 2008, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) DESK & OFFICE CLEANER 573
MANUFACTURER: 3M
DIVISION: Office Supplies Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 06/17/2008
Supercedes Date: 07/18/2007
Document Group: 23-3022-3
Product Use:
Intended Use:
Specific Use:
Aerosol foam cleaner for office surfaces.
Aerosol foam cleaner for office surfaces.
SECTION 2: INGREDIENTS
Ingredient
C.A.S. No.
WATER
ISOBUTANE PROPELLANT
ISOPROPYL ALCOHOL
ETHOXYLATED ALCOHOLS
SODIUM CARBONATE
FRAGRANCE
7732-18-5
75-28-5
67-63-0
68439-46-3
497-19-8
Trade Secret
% by Wt
80 - 95
1- 5
3- 5
1- 3
0- 1
0 - 0.5
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Specific Physical Form: Foam
Odor, Color, Grade: White foam, Clean/Fresh Scent
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Flammable liquid and vapor. Closed containers exposed to heat from
fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
May cause target organ effects.
_________________________________________________________________________________________________
Page 1 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) DESK & OFFICE CLEANER 573
06/17/2008
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Inhalation:
Intentional concentration and inhalation may be harmful or fatal.
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
Single exposure, above recommended guidelines, may cause:
Cardiac Sensitization: Signs/symptoms may include irregular heartbeat (arrhythmia), faintness, chest pain, and may be fatal.
Simple Asphyxiation: Signs/symptoms may include increased heart rate, rapid respirations, drowsiness, headache,
incoordination, altered judgement, nausea, vomiting, lethargy, seizures, coma, and may be fatal.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Prolonged or repeated exposure may cause:
Dermal Effects: Signs/symptoms may include localized redness, itching, drying and cracking of skin.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
_________________________________________________________________________________________________
Page 2 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) DESK & OFFICE CLEANER 573
06/17/2008
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air.
Get immediate medical attention.
If Swallowed:
Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
4.2 NOTE TO PHYSICIANS
Exposure may increase myocardial irritability. Do not administer sympathomimetic drugs unless absolutely necessary.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
No Data Available
<=0 ºF [Details: Propellent]
1.80 %
12.7 % [Details: for propellent]
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Flammable liquid and vapor. Closed containers exposed to heat from fire may build
pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Refer to other sections of this MSDS for information regarding physical and health hazards,
respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information
on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up
by qualified personnel. If possible, seal leaking container. Place leaking containers in a well-ventilated area, preferably an operating
exhaust hood, or if necessary outdoors on an impermeable surface until appropriate packaging for the leaking container or its contents
is available. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse
or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause
flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build dikes to prevent
entry into sewer systems or bodies of water. Cover spill area with a fire-extinguishing foam designed for use on solvents, such as
alcohols and acetone, that can dissolve in water. An AR - AFFF type foam is recommended. Working from around the edges of the
spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent
until it appears dry. Collect as much of the spilled material as possible. Collect as much of the spilled material as possible using nonsparking tools. Clean up residue with detergent and water. Collect the resulting residue containing solution. Place in an approved
metal container. Seal the container. Dispose of collected material as soon as possible.
_________________________________________________________________________________________________
Page 3 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) DESK & OFFICE CLEANER 573
06/17/2008
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Avoid eye contact. Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
Contents may be under pressure, open carefully. Keep away from heat, sparks, open flame, pilot lights and other sources of ignition.
Ground containers securely when transferring contents. Wear low static or properly grounded shoes. No smoking while handling this
material. Do not spray near flames or sources of ignition. Avoid breathing of vapors, mists or spray. Avoid prolonged or repeated
skin contact. Aerosol container contains flammable gas under pressure. Avoid static discharge. Avoid eye contact with vapors,
mists, or spray. Keep out of the reach of children. Avoid contact with oxidizing agents.
7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area. Keep container
tightly closed. Store away from oxidizing agents.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Do not use in a confined area or areas with little or no air movement. Do not remain in area where available oxygen may be reduced.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
8.2.2 Skin Protection
Gloves not normally required. Avoid prolonged or repeated skin contact.
8.2.3 Respiratory Protection
Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection. Avoid
breathing of vapors, mists or spray.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges and N95 particulate prefilters.
Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Not applicable.
8.3 EXPOSURE GUIDELINES
Ingredient
ISOBUTANE PROPELLANT
ISOPROPYL ALCOHOL
ISOPROPYL ALCOHOL
ISOPROPYL ALCOHOL
ISOPROPYL ALCOHOL
Authority
Type
Limit
Additional Information
ACGIH
ACGIH
ACGIH
OSHA
OSHA
TWA
TWA
STEL
TWA
STEL
1000 ppm
200 ppm
400 ppm
400 ppm
500 ppm
Table A4
Table A4
Table Z-1A
Table Z-1A
_________________________________________________________________________________________________
Page 4 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) DESK & OFFICE CLEANER 573
06/17/2008
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Specific Physical Form:
Odor, Color, Grade:
General Physical Form:
Autoignition temperature
Flash Point
Flammable Limits - LEL
Flammable Limits - UEL
Boiling point
Density
Vapor Density
Foam
White foam, Clean/Fresh Scent
Liquid
No Data Available
<=0 ºF [Details: Propellent]
1.80 %
12.7 % [Details: for propellent]
10 - 213 ºF
1 g/ml
No Data Available
Vapor Pressure
31 - 43 psi [@ 70 ºF] [Details: (aerosol can pressure)]
Specific Gravity
pH
Melting point
Solubility In Water
Approximately 1 [Ref Std: WATER=1]
11 - 12
Not Applicable
No Data Available
Evaporation rate
>=1.00 [Ref Std: WATER=1] [Details: product as applied (without
propellant)]
5.77 % weight
96 - 98 % weight
No Data Available
Not Applicable
Volatile Organic Compounds
Percent volatile
VOC Less H2O & Exempt Solvents
Viscosity
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Heat; Sparks and/or flames
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance
Condition
Hydrocarbons
Carbon monoxide
Carbon dioxide
During Combustion
During Combustion
During Combustion
_________________________________________________________________________________________________
Page 5 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) DESK & OFFICE CLEANER 573
06/17/2008
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in a permitted hazardous waste incinerator. As a disposal alternative, dispose of waste product
in a permitted hazardous waste facility.
The facility should be equipped to handle gaseous waste.
Facility must be capable of handling aerosol cans. Dispose of empty product containers in a sanitary landfill.
Do not puncture or burn cans in a household incinerator.
EPA Hazardous Waste Number (RCRA): D001 (Ignitable)
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
70-0714-9577-7
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - Yes
Reactivity Hazard - No
Immediate Hazard - Yes
Delayed Hazard - No
_________________________________________________________________________________________________
Page 6 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) DESK & OFFICE CLEANER 573
06/17/2008
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
WHMIS: Hazardous
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 3
Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
HMIS Hazard Classification
Health: 2 Flammability: 3
Reactivity: 0
Protection: X - See PPE section.
Hazardous Material Identification System (HMIS(r)) hazard ratings are designed to inform employees of chemical hazards in the workplace. These
ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency
situations. HMIS(r) ratings are to be used with a fully implemented HMIS(r) program. HMIS(r) is a registered mark of the National Paint and
Coatings Association (NPCA).
Revision Changes:
Copyright was modified.
Section 14: ID Number Heading Template 1 was added.
Section 14: ID Number(s) Template 1 was added.
Section 2: Ingredient table was added.
Section 8: Exposure guidelines ingredient information was added.
_________________________________________________________________________________________________
Page 7 of 8
MATERIAL SAFETY DATA SHEET 3M(TM) DESK & OFFICE CLEANER 573
06/17/2008
Section 8: Exposure guidelines data source legend was added.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 8 of 8