Audio2Car
Audio2Car
The professional mute
The professional mute
Audio2Car harness
Product Description
The Audio2Car range allows OEM car speakers to be used for aftermarket Audio equipment.
Audio2Car allow the car speakers to be used for audio playback from aftermarket Audio equipment. For a complete installation two or more item numbers are required. See description at the last page.
For a complete installation normally a minimum of two item numbers are required.
Audio equipment with build in mute function:
If the Audio equipment is equipped with a build in mute function two item numbers
are required. The 1st item number is the Audio2Car harness. The 2nd item is a
Audio2Car carkit adaptor.
Audio equipment without build in mute function:
If the Audio equipment is not equipped with speaker relays, a Mute-box from Kram
Drive & Talk range can be added together with a Drive & Talk carkit adaptor.
Speaker-function: This is achieved by connecting Audio equipment with build-in speaker relay function or by
using a Mute-box from the Kram range. This way the radio sound is muted and the sound from the aftermarket
Audio equipment is sent through the car speakers. You will achieve a perfect sound without interference from
the car radio.
Mute wire function: The mute-wire is connected from the 24 pin connector to the most used mute position for
the car model. This enables the use of the radios built in mute function. If the radio does not have such function
or the mute exists in a different connector than the ones used on the Audio2Car harness, the mute wire can be
found in a yellow fly-wire fitted with a bullet connector.
Power supply: All Audio2Car cables have an integrated power supply for the Audio equipment in the 24 pin
connector. The constant 12v and the ground supply are normally sourced from the radio supply. This way power
supply of most Audio Equipment can be achieved without cutting the cars wiring loom. The constant 12V wires
are red and the ground wires are black.
Audio2Car Carkit Adaptors
Several different carkit adaptors
are available for Carkits that
have a build in mute function
for 1 or 4 Speakers.
Please see the complete range
of Audio2Car carkit adaptors
at our website:
www.kram.dk
Ignition supply: If an ignition source is available in the radio connector then it will normally also be available in
the 24 pin connector. If an ignition source is not available a constant 12V source is connected to the Ignition pin
via bullet connectors. If a real ignition is required for the chosen Audio Equipment, an IGNIBOX item no. “I” can
be connected to create an artificial ignition. Or an ignition source found elsewhere can be connected to the
bullet with the blue wire. The 12V ignition wires in the Audio2Car cable are blue.
Aux integration
The 4 pin connector on the Audio2Car harness allow a Kram Aux solution to be connected. This will allow the
use of the car sound system amplifier for Music playback and thereby achieving higher sound quality.
Examples of
carkit adaptors
Technical Specifications
Audio2Car Accessories examples
ISO adaptor
IGNIBOX adaptor
Drive & talk Mute-box
range
Description:
L-shaped with bullet connections for Ground, Constant 12v and Ignition.
Normal Wire dimensions :
AWG 18 for power wires, AWG 20 for all other wires
Standard Fuse sizes:
2 Amp for constant supply, 1 Amp for Ignition supply
Maximum Fuse size:
7,5 Amp for constant supply, 7,5 Amp for Ignition supply
Maximum output pr. speaker:
100 Watt RMS / 200 Watt music power @ 4 Ohm
Size:
400 x 400 mm
Configuration chart for 24 pin connector:
This ISO adaptor AA010 is a
universal adaptor for all
carkits with ISO connectors.
Adding this adaptor turns
your Audio2Car cable into a
Kram ISO2CAR solution.
This IGNIBOX ITEM no. “I”
creates an artificial ignition
source. Use this adaptor if
your Audio2Car cable does
not include an ignition source.
This adaptor is plug and play
with your Audio2Car cable.
Several different types of mute-boxes are
available. Adding one of the boxes will
turn your Audio2Car cable into a Kram
Drive & Talk solution. Therefore you will
also need a Drive & Talk carkit adaptor.
Please see the Complete Drive & Talk
range at our website:
www.kram.dk
12V
Const.
12V
IGN
Line
Out L-
Line
Out R-
Radio
RR+
Radio
RF+
Radio
LF+
Radio
LR+
Spk
LR+
Spk
LF+
Spk
RF+
Spk
RR+
GND
Mute
Line
Out L+
Line
Out R+
Radio
RR-
Radio
RF-
Radio
LF-
Radio
LR-
Spk
LR-
Spk
LF-
Spk
RF-
Spk
RR-
Connector seen from cable entry side
EN066-V01
Audio2Car
Audio2Car
The professional mute
The professional mute
should not be bigger than the ones used on the wiring loom supplied with the carkit. The fuses on the Audio2Car
cable should be replaced with a size similar to the ones supplied with the carkit.
Note: Never exceed the Maximum Fuse size for the Audio2Car cable. See first page.
Installation description
for 84066 Audio2Car harness used for
Audi cars with Bang & Olufsen sound system.
Needed items:
A: Audio2Car harness including Mute-box & Mute-loop.
B: Audio2Car extension cable (bought separately).
C: Audio2Car carkit adaptor (bought separately).
D: Carkit (bought separately).
Note: B & C can be replaced by an additional Mute-box
and extension cable from our Drive & Talk range.
Identification of sound system:
This cable will only fit cars equipped with Bang & Olufsen
sound system. If you do not have Bang & Olufsen logos on
the speaker grill a different cable set will be required.
Please see our complete cable list for further information
about choosing the right cable for your sound system. The
list can be downloaded at www.kram.dk
Bullet Connectors
6th: Extend the cable-set to the preferred location of the carkit. Use the extension cable B (or additional Drive &
Talk Mute-box with extension cable) to extend the cable-set to the preferred location of the carkit. Behind the
glove-box is recommended.
A: Audio2Car Harness
Item number 84xxx
7th: Connect the carkit adaptor. Connect the carkit adaptor to the extension cable. Connect the carkit adaptor to
the carkit.
24 pin Connectors
Mute-box
B: Audio2Car Extension
cable Item number AEx
24 pin Connectors
Mute-loop
C: Audio2Car Adaptor
Item number AAxxx
Troubleshooting Guide
D: Carkit
Installation:
When delivered this Audio2Car cable-set is always fitted
with a Mute-box and a Mute-loop connector.
1st: Remove the key from the ignition barrel. This is
done to avoid error messages on the cars electrical system. Such error can only be reset by an authorised Audi
Repair shop.
2nd: Locate & uncover the amplifier unit. Amplifier
locations:
♦
Audi A4, A4 Allroad, A5 install on amplifier in
the left side of the boot. See picture on the right.
An Audio2Car extension cable item no. AE5 is
also required.
♦
Audi Q5 install on amplifier in the left side of
the boot. See picture on the right. An Audio2Car
extension cable item no. AE5 is also required.
♦
Audi R8 install on amplifier under rear shelf.
Audio2Car extension cable item no. AE5 is also
required.
Left Rear
Wheel arc
Amplifier
Amplifier location in Audi A4, A4 Allroad & A5
3rd: Connect the car-specific cable. Disconnect the
connector on the amplifier unit and insert the Audio2Car
harness between the connector and amplifier unit.
4th: Check ignition source. When the cable-set is delivered the blue ignition wire is connected to the red constant 12V wire with a bullet connector. If a real ignition
source is needed for the chosen carkit an IGNIBOX item no.
“I” can be inserted to create an artificial ignition source or
the blue ignition wire can be disconnected from the red
constant 12v and manually connected to an ignition
source found elsewhere.
5th: Check fuse size. The fuse on the Audio2Car cable
Amplifier
Amplifier location in Audi Q5
Carkit does not start up. Check if there is 12V between the black and the red wire and also between the black and
blue wire, in the 24 pin connector, when the car is started. If there is not 12v on both wires please check the following:
1.
If there is supply on the red constant 12v wire but not on the blue ignition wire the car may require an
alternative ignition source. See installation step 4.
2.
Check that the bullets on the supply wires are properly connected. The supply wires are the red, blue and
black wires.
3.
Check for a blown fuse on the Audio2Car harness or in the cars fuse-box.
The carkit does not turn off when the key is removed from the ignition barrel. Your carkit needs a real ignition
source. Please check the following:
1.
Is there an ignition supply on the blue wire? There should be no voltage on the blue wire when there is no
key in the ignition. See installation step 4.
Not all speakers are muted. Try to disconnect the Mute-box and the Carkit adaptor C (or additional Drive and Talk
mute-box) from the Audio2Car harness then turn on the radio and check the following :
1.
All front door speakers keep playing: This is the wrong Audio2Car harness for this car / sound system.
2.
A few speakers keep playing: This is the wrong Audio2Car harness for this car / sound system.
3.
All speakers are now muted:
♦
Carkits with 1 speaker mute: Some carkits can only mute 1 speaker channel with their build in
mute-box. This is normally stated on the label on the carkit adaptor for these carkits, else please
check the carkit manual. If a full mute is desired with these carkits, then this can be achieved by
adding an additional mute-box from our Drive & Talk range.
♦
Carkits with 4 speaker channel mute: (or when additional Drive & Talk mute-box is used): Please
check that the “Mute-Loop” is attached to Mute-box delivered with the cable-set. Else please try
another carkit.
Carkit sound is in the wrong speakers or there is no carkit sound.
1.
The two 24 pin connectors in the cable-set may be switched. The carkit should be connected to the 24 pin
connector with the Green, White, Gray and Purple wires.
2.
The carkit may be defective. Please try another carkit.
Radio will not turn on or not working properly after installation.
1.
Please check for a blown fuse at the radio or in the car fuse-box.
2.
Remove the Audio2Car harness and connect the radio to the original car connector. If the radio is now
working replace the Audio2car harness.
See our complete Radio Mute program on our website www.kram.dk