LG 22LH20 22" Black LCD TV

LCD TV
OWNER’S MANUAL
19LH20
22LH20
26LH20
32LH20
37LH20
42LH20
22LH200C
32LH30
37LH30
42LH30
47LH30
19LU55
22LU55
26LU55
32CL20
32LF11
37LF11
42LF11
47LF11
47LF21
Please read this manual carefully before operating
your set and retain it for future reference.
The model and serial number of the TV is located
on the back and one side of the TV.
Record it below should you ever need service.
Model:
Serial:
This product qualifies for ENERGY STAR in the “factory
default (Home Use)” setting.
1-800-243-0000
USA, Consumer User
1-888-865-3026
1-888-542-2623
USA, Commercial User
CANADA
LG Customer Information Center
Changing the factory default settings or enabling other features may increase power consumption that could exceed the
limits necessary to quality for ENERGY STAR.
P/NO : SAC33601901 (0905-REV04)
www.lgusa.com / www.lg.ca / www.lgcommercial.com
WARNING / CAUTION
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.
2
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause (harmful) interference,
and (2) this device must accept any interference
received, including interference that may cause undesired operation (of the device).
Any changes or modifications in construction of this
device which are not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product.
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
1
2
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
7
Only use attachments/accessories specified by
the manufacturer.
8
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
9
Unplug this apparatus during lighting storms
or when unused for long periods of time.
10
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
Do not use this apparatus near water.
Clean only with dry cloth.
3
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
4
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
5
6
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a
third grounding prong, The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
3
SAFETY INSTRUCTIONS
4
11
Never touch this apparatus or antenna during
a thunder or lighting storm.
12
When mounting a TV on the wall, make sure
not to install the TV by the hanging power and
signal cables on the back of the TV.
13
Do not allow an impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.
14
CAUTION concerning the Power Cord:
It is recommend that appliances be placed
upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance
and has no additional outlets or branch
circuits. Check the specification page of this
owner's manual to be certain.
Do not connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of
the appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not make the TV with the power cord
plugged in. Do not use a damaged or loose
power cord. Be sure do grasp the plug when
unplugging the power cord. Do not pull on the
power cord to unplug the TV.
15
WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids. Do not touch the TV
with wet hands. Do not install this product
near flammable objects such as gasoline or
candles or expose the TV to direct air
conditioning.
16
Do not expose to dripping or splashing and do
not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g.
on shelves above the unit).
17
GROUNDING
Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e. a TV
with a three-prong grounded AC plug must be
connected to a three-prong grounded AC outlet). If grounding methods are not possible,
have a qualified electrician install a separate
circuit breaker.
Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas
pipes.
Short-circuit
Breaker
Power
Supply
18
DISCONNECTING DEVICE FROM MAINS
Mains plug is the disconnecting device. The
plug must remain readily operable.
19
As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC
power source even if you turn off this unit by
SWITCH.
20
ANTENNAS
Outdoor antenna grounding
If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system
should not be located in the vicinity of overhead power lines or other electric light or
power circuits, or where it can come in contact
with such power lines or circuits as death or
serious injury can occur.
Be sure the antenna system is grounded so as
to provide some protection against voltage
surges and built-up static charges.
Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding
electrode.
Antenna grounding according to the
National Electrical Code, ANSI/NFPA 70
Ground Clamp
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
NEC: National Electrical Code
21
22
Cleaning
When cleaning, unplug the power cord and
scrub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners or benzene.
Moving
Make sure the product is turned off,
unplugged and all cables have been removed. It
may take 2 or more people to carry larger TVs.
Do not press against or put stress on the front
panel of the TV.
23
Ventilation
Install your TV where there is proper ventilation. Do not install in a confined space such as
a bookcase. Do not cover the product with
cloth or other materials (e.g.) plastic while
plugged in. Do not install in excessively dusty
places.
24
If you smell smoke or other odors coming from
the TV or hear strange sounds, unplug the power
cord contact an authorized service center.
25
Do not press strongly upon the panel with
hand or sharp object such as nail, pencil or
pen, or make a scratch on it.
26
Keep the product away from direct sunlight.
27
For LCD TV
If the TV feels cold to the touch, there may be
a small “flicker” when it is turned on. This is
normal, there is nothing wrong with TV.
Some minute dot defects may be visible on the
screen, appearing as tiny red, green, or blue
spots. However, they have no adverse effect on
the monitor's performance.
Avoid touching the LCD screen or holding your
finger(s) against it for long periods of time.
Doing so may produce some temporary distortion effects on the screen.
ON DISPOSAL
(Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains
a small amount of mercury. Do not dispose of
this product with general household waste.
Disposal of this product must be carried out in
accordance to the regulations of your local authority.
5
CONTENTS
WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FEATURE OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PREPARATION
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Stand Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Positioning your Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Kensington Security System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Securing the TV to the wall to prevent falling when
the TV is used on a stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 31
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Audio out Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
WATCHING TV / CHANNEL CONTROL
Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
6
Channel Setup
- Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
- Add / Delete Channel (Manual Tuning) . . . . . . 55
- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Favorite Channel Setup / Favorite Channel List . . 58
Brief Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
AV Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Simple Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
SIMPLINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 66
Picture Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Preset Picture Settings (Picture Mode) . . . . . . . . . . . . . 70
Manual Picture Adjustment - User Mode . . . . . . . . . . 71
Picture Improvement Technology . . . . . . . . . . . . . . . . . . . . . 72
Expert Picture Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Energy Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Demo Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
SOUND & LANGUAGE CONTROL
Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 80
Clear Voice II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Preset Sound Setting (Sound Mode) . . . . . . . . . . . . . . . . 82
Sound Setting Adjustment - User Mode . . . . . . . . . . . 83
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Audio Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
On-Screen Menus Language Selection . . . . . . . . . . . . . 89
Caption Mode
- Analog Broadcasting System Captions . . . . . . . 90
- Digital Broadcasting System Captions . . . . . . . . 91
- Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
TIME SETTING
Clock Setting
- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
APPENDIX
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
External Control Through RS-232C . . . . . . . . . . . . . . . . .116
Open Source License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
7
FEATURE OF THIS TV
High-definition television. High-resolution digital
television broadcast and playback system composed
of roughly a million or more pixels, 16:9 aspect-ratio
screens, and AC3 digital audio. A subset of digital
television, HDTV formats include 1080i and 720p
resolutions.
Manufactured under license from Dolby Laboratories.
“Dolby “and the double-D symbol are trademarks of
Dolby Laboratories.
is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.
This TV contains the detailed calibrations necessary
for professional certification by the Imaging Science
Foundation. The resulting ISF “day” and “night” modes
will then be accessible by the user to experience the
best their LG HDTV has to offer.
CALIBRATE LIKE A PRO: Sophisticated and detailed
calibrations can be made through the ISFccc mode.
Detailed calibration requires a licensed technician.
Please contact your local dealer to inquire about an
ISF certified technician.
The AV Mode optimizes the picture into Cinema,
Sports, and game Mode according to the video and
audio content. The viewer has the ability to quickly
choose the correct mode for the picture they are
viewing.
Automatically enhances and amplifies the sound of
human voice frequency range to help keep dialogue
audible when background noise swells.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."
LG TV include a unique invisible speaker system,
tuned by renowned audio expert, Mr. Mark Levinson.
Speakers are embedded in strategic spots behind the
front cabinet and use minute vibrations to turn the
entire front bezel into the speaker system. The result
is a clean, polished look, and enhanced audio by
increasing the “sweet spot”, giving a wider and richer
sound field.
IMPORTANT INFORMATION TO PREVENT “IMAGE BURN
/ BURN-IN” ON YOUR TV SCREEN
■
■
■
8
When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV
for an extended period, it can become permanently imprinted on the screen. This phenomenon is known
as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.
In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period
(2 or more hours for LCD, 1 or more hours for Plasma).
Image burn can also occur on the letterboxed
areas of your TV if you use the 4:3 aspect ratio
setting for an extended period.
PREPARATION
ACCESSORIES
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.
The accessories included may differ from the images below.
7
5
3
8
T
L
0
6
9
FLAS
HBK
MU
TE
IN
FO
AV
CH
EN
E
TE
A
G
P
MOD
E
1
R
4
7
RE
LIS
TU
RN
VO
L
IN
PU
GY T
SAVIN
G
3
6
0
9
FLAS
HBK
MU
TE
CH
E
EN
ENER
5
8
T
PO
W
ER
2
A
G
P
TE
R
MEN
U
Q.ME
NU
RE
TU
RN
MAR
FA K
V
Owner’s Manual
1.5V 1.5V
Remote Control,
Batteries
CD Manual
Power Cord
Option Extras
Not included with all models
* Wipe spots on the exterior only with
the polishing cloth.
Polishing Cloth
PREPARATION
LIS
VO
* Do not wipe roughly when removing
stain. Excessive pressure may cause
scratch or discoloration.
D-sub 15 pin Cable
When using the VGA (D-sub 15 pin
cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain
standards compliance.
For 19/22/26LU55
(For 26LU55)
(For 26LU55)
(For 19/22LU55)
x3
x2
Bolts for stand assembly
(Refer to P.22)
Cable Holder
(Refer to P.25)
Screw for stand fixing
(Refer to P.29)
For 19/22LH20, 22LH200C
For 32/37/42/47LF11, 47LF21, 32CL20
(Except 47LF11, 47LF21)
x4
Cable Management Clip Protection Cover
(Refer to P.17)
(Refer to P.26)
(Except 47LF11, 47LF21)
x4
Bolts for stand assembly Screw for stand fixing
(Refer to P.20)
(Refer to P.29)
or
Protection Cover
(Refer to P.21)
Only 26/32/37/42LH20, 32/37/42/47LH30
(Except 47LH30)
x4
Bolts for stand assembly
(Refer to P.18)
Screw for stand fixing
(Refer to P.29)
Protection Cover
(Refer to P.19)
9
PREPARATION
FRONT PANEL INFORMATION
■
Image shown may differ from your TV.
PREPARATION
19/22/26LH20, 22LH200C
MENU Button
INPUT Button
POWER Button
ENTER
Button
INPUT MENU ENTER
VOLUME
CHANNEL
(-, +) Buttons (E,D) Buttons
VOL
CH
32/37/42LH20, 32/37/42/47LH30
CH
CHANNEL (D,E)
Buttons
VOL
VOLUME (+, -)
Buttons
ENTER
ENTER Button
MENU
MENU Button
INPUT
INPUT Button
SPEAKER
Remote Control Sensor,
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the TV is switched on.
(Can be adjusted P o w e r I n d i c a t o r in the
OPTION menu. G p . 7 8)
POWER Button
ON
OFF
AC power control switch
(Except 19/22LH20, 22LH200C)
10
PREPARATION
32/37/42/47LF11, 47LF21, 32CL20
CH
VOL
CHANNEL (
Buttons
,
)
VOLUME (+, -)
Buttons
SPEAKER
ENTER
ENTER Button
MENU
MENU Button
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the set is switched on.
INPUT
INPUT Button
Remote Control Sensor
POWER Button
11
PREPARATION
■
Image shown may differ from your TV.
PREPARATION
19/22LU55
MENU Button
ENTER Button
INPUT Button
POWER Button
INPUT MENU ENTER
VOLUME
CHANNEL
(-, +) Buttons ( , ) Buttons
VOL
CH
26LU55
CH
VOL
CHANNEL (
Buttons
,
VOLUME (+, -)
Buttons
ENTER Button
ENTER
MENU Button
MENU
INPUT Button
INPUT
POWER Button
SPEAKER
Remote Control Sensor
❖N
❖❋❋
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates white when the TV is
switched on.
12
AC power control
switch
)
BACK PANEL INFORMATION
■
Image shown may differ from your TV.
PREPARATION
❖N
❖❋❋
9
9
19/22LH20, 22LH200C
1
2
VIDEO
3
4
AV IN
AUDIO
RGB(PC) IN
USB IN
SERVICE ONLY
/DVI IN
L(MONO) R
ANTENNA
AUDIO IN /CABLE IN
(RGB/DVI)
L
R
VIDEO
AUDIO
COMPONENT IN
RS-232C IN
(CONTROL&SERVICE)
8
7
6
26/32/37/42LH20, 19/22LU55, 32CL20
2
1
4
3
AV IN
VIDEO
USB IN
SERVICE ONLY
5
RGB IN (PC)
AUDIO
L(MONO) R
AUDIO IN
(RGB/DVI)
OPTICAL DIGITAL
AUDIO OUT
2
L
VIDEO
R
AUDIO
1
COMPONENT IN
/DVI IN
8
RS-232C IN
(CONTROL&SERVICE)
7
ANTENNA/
CABLE IN
6
13
PREPARATION
■
Image shown may differ from your TV.
R
PREPARATION
9
9
32/37/42/47LH30, 26LU55, 32/37/42/47LF11, 47LF21
4
3
AV IN1
L(MONO) R
AUDIO IN
OPTICAL DIGITAL
AUDIO OUT
2
(RGB/DVI)
L
VIDEO
R
AUDIO
1
COMPONENT IN
/DVI IN
8
RS-232C IN
(CONTROL&SERVICE)
7
ANTENNA/
CABLE IN
6
AV IN 2
14
3
RGB IN (PC)
AUDIO
VIDEO L/MONO AUDIO R
VIDEO
USB IN
SERVICE ONLY
5
IN 3
2
1
2
PREPARATION
1
USB IN SERVICE ONLY
Used for software updates.
2
AV (Audio/Video) IN
Analog composite connection. Supports standard
definition video only (480i).
3
HDMI/DVI IN, HDMI IN
Digital Connection.
Supports HD video and Digital audio. Doesn’t
support 480i.
Accepts DVI video using an adapter or HDMI to
DVI cable (not included).
4
RGB IN (PC)
Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).
AUDIO IN (RGB/DVI)
1/8" (0.32 cm) headphone jack for analog PC
audio input.
5
OPTICAL DIGITAL AUDIO OUT
(Except 19/22LH20, 22LH200C)
Digital optical audio output for use with amps and
home theater systems.
Note: In standby mode, this port doesn’t work.
6
ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
7
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices.
This port is used for Service or Hotel mode.
8
COMPONENT IN
Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video & red
and white for audio.
9
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
15
PREPARATION
STAND INSTRUCTIONS (For 19/22LH20, 22LH200C)
■
PREPARATION
16
Image shown may differ from your TV.
INSTALLATION
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Assemble the TV as shown until you hear it click.
DETACHMENT
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Loose the bolts from TV.
3
Detach the stand from TV.
PREPARATION
1
PROTECTION COVER
4
Insert the P R O T E C T I O N C O V E R into the TV.
PROTECTION COVER
5
Fix the 4 bolts securely using the holes in the
back of the TV.
17
PREPARATION
STAND INSTRUCTIONS (For 26/32/37/42LH20, 32/37/42/47LH30)
■
Image shown may differ from your TV.
PREPARATION
INSTALLATION
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Assemble the TV as shown.
3
Fix the 4 bolts securely using the holes in the
back of the TV.
! NOTE
G
18
When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully,
the TV can tilt forward after the product installation). Do not over tighten.
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Loose the bolts from TV.
3
Detach the stand from TV.
PREPARATION
DETACHMENT
PROTECTION COVER
After removing the stand, install the included
p r o t e c t i o n c o v e r over the hole for the stand.
Press the P R O T E C T I O N C O V E R into the TV
until you hear it click.
19
PREPARATION
STAND INSTRUCTIONS (For 32/37/42/47LF11, 47LF21, 32CL20)
■
Image shown may differ from your TV.
PREPARATION
INSTALLATION (For 32/37/42LF11, 32CL20)
1
If your TV has a protection tape attached,
remove the tape.
And carefully place the TV screen side down
on a cushioned surface to protect the screen
from damage.
2
Assemble the parts of the S T A N D B O D Y
with C O V E R B A S E of the TV by using the 4
screws supplied.
STAND BODY
COVER BASE
3
Assemble the TV as shown.
4
Fix the 4 bolts securely using the holes in the
back of the TV.
! NOTE
G
20
When assembling the desk type stand, make sure
the screws are fully tightened (If not tightened
fully, the TV can tilt forward after the product
installation). Do not over tighten.
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Loose the bolts from TV.
3
Detach the stand from TV.
PREPARATION
DETACHMENT
PROTECTION COVER
After removing the stand, install the included
p r o t e c t i o n c o v e r over the hole for the stand.
Press the P R O T E C T I O N C O V E R into the TV
until you hear it click.
21
PREPARATION
STAND INSTRUCTIONS (For 19/22/26LU55)
■
Image shown may differ from your TV.
PREPARATION
INSTALLATION
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Fix the bolts securely using the holes.
19/22LU55
19"
22"
! NOTE
G
When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully,
the TV can tilt forward after the product installation). Do not over tighten.
26LU55
19"
22
22"
26"
DETACHMENT
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
2
Loose the bolts and then detach the stand
from TV.
19"
3
Loose the bolts from TV.
And detach the C O V E R B A S E from TV.
PREPARATION
1
19/22LU55
19"
26LU55
22"
22"
COVER BASE
19/22LU55
4
Detach the S T A N D B O D Y from TV.
26"
26"
26LU55
STAND BODY
23
PREPARATION
VESA WALL MOUNTING
PREPARATION
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please
contact your nearest installer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.
VESA (A * B)
Model
A
B
19LU55, 22LU55,
19LH20,
22LH20, 22LH200C
100 * 100
Standard Screw
Quantity
M4
4
Wall Mounting Bracket
(sold separately)
RW120
26LH20, 26LU55
200 * 100
M4
RW230
4
32LH20, 32LH30,
32LF11,
32CL20
RW230
37LH20, 37LH30,
37LF11,
42LH20, 42LH30,
42LF11, 47LF11,
47LF21, 47LH30
200 * 200
M6
AW-47LG30M
4
AW-47LG30M
! NOTE
G
G
G
G
G
Screw length needed depends on the wall mount
used. For further information, refer to the instructions included with the mount.
Standard dimensions for wall mount kits are shown
in the table.
When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.
Do not use screws longer then the standard dimension, as they may cause damage to the inside to
the TV.
For wall mounts that do not comply with the VESA
CAUTION
24
G
G
G
standard screw specifications, the length of the
screws may differ depending on their specifications.
Do not use screws that do not comply with the
VESA standard screw specifications.
Do not use fasten the screws too strongly, this may
damage the TV or cause the TV to a fall, leading to
personal injury. LG is not liable for these kinds of
accidents.
LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is
used or the consumer fails to follow the TV installation instructions.
Do not install your wall mount kit while your TV is turned on. It may result in personal
injury due to electric shock.
CABLE MANAGEMENT
■
Image shown may differ from your TV.
1
PREPARATION
For 19/22/26LU55
After connecting the cables as necessary,
install CABLE HOLDER as shown and bundle
the cables.
For 32/37/42/47LF11, 47LF21, 32CL20
1
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
2
Install the CABLE MANAGEMENT CLIP as shown.
CABLE MANAGEMENT CLIP
3
Fit the CABLE MANAGEMENT CLIP as shown.
25
PREPARATION
CABLE MANAGEMENT
■
Image shown may differ from your TV.
For 19/22LH20, 22LH200C
PREPARATION
1
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
2
Install the CABLE MANAGEMENT CLIP as shown.
CABLE MANAGEMENT CLIP
3
Fit the CABLE MANAGEMENT CLIP as shown.
How to remove the CABLE MANAGEMENT CLIP
G
Hold the CABLE MANAGEMENT CLIP with both hands and pull it
backward.
! NOTE
G
26
Do not hold the CABLE MANAGEMENT CLIP when moving the TV.
- If the TV is dropped, you may be injured or the product may be broken.
For 26/32/37/42LH20, 32/37/42/47LH30
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
2
Install the CABLE MANAGEMENT CLIP as
shown.
PREPARATION
1
CABLE MANAGEMENT CLIP
3
Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.
27
PREPARATION
DESKTOP PEDESTAL INSTALLATION
■
Image shown may differ from your TV.
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
PREPARATION
4 inches
4 inches
4 inches
4 inches
G
CAUTION
G
Ensure adequate ventilation by following the clearance recommendations.
Do not mount near or above any type of heat source.
SWIVEL STAND (Except 19/22LH20, 22LH200C, 19/22/26LU55)
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit
your viewing position.
POSITIONING YOUR DISPLAY (For 19/22LH20, 22LH200C)
■
■
Here shown may be somewhat different from your TV.
Adjust the position of the panel in various ways for maximum comfort.
• Tilt range
12
0
0
3
! NOTE
G
28
19/22/26LU55 have a fixed stand type without the tilt and swivel features so excessive pressure may
damage the TV.
ATTACHING THE TV TO A DESK
(Except 19/22LH20, 22LH200C,19/22LU55, 47LH30, 47LF11, 47LF21)
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.
PREPARATION
Stand
1-Screw
(provided as parts of the product)
Desk
Stand
1-Screw
(provided as parts of the product)
Desk
WARNING
G
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.
KENSINGTON SECURITY SYSTEM
■
This feature is not available for all models.
- The TV is equipped with a Kensington Security System connector on
the back panel. Connect the Kensington Security System cable as
shown below.
- For the detailed installation and use of the Kensington Security
System, refer to the user’s guide provided with the Kensington
Security System.
For further information, contact h t t p : / / w w w . k e n s i n g t o n . c o m,
the internet homepage of the Kensington company. Kensington sells
security systems for expensive electronic equipment such as notebook PCs and LCD projectors.
NOTE: The Kensington Security System is an optional accessory.
29
PREPARATION
SECURING THE TV TO THE WALL TO PREVENT FALLING
WHEN THE TV IS USED ON A STAND
■
PREPARATION
■
You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).
Image shown may differ from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
■
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is
mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
■
Use a sturdy rope (sold separately) to tie the product. It is safer to tie
the rope so it becomes horizontal between the wall and the product.
! NOTE
G
G
30
Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.
■
■
To prevent damage do not connect to the power outlet until all connections are made between the devices.
Image shown may differ from your TV.
ANTENNA OR CABLE CONNECTION
PREPARATION
1. Antenna (Analog or Digital)
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.
For optimum picture quality, adjust antenna direction if needed.
Wall
Antenna
Socket
Outdoor
Antenna
(VHF, UHF)
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
ANTENNA/
CABLE IN
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
Copper Wire
Be careful not to bend the copper wire
when connecting the antenna.
2. Cable
ANTENNA/
CABLE IN
Cable TV
Wall Jack
RF Coaxial Wire (75 ohm)
To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■ If the antenna is not installed properly, contact your dealer for assistance.
■
■
31
EXTERNAL EQUIPMENT SETUP
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
■ This part of EXTERNAL EQUIPMENT SETUP mainly use picture for 2 6 / 3 2 / 3 7 / 4 2 L H 2 0.
■
HD RECEIVER SETUP
This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if
you do receive digital signals from a digital set-top box or other digital external device.
EXTERNAL EQUIPMENT SETUP
Component Connection
1. How to connect
Y
1
PB
PR
L
R
Connect the video outputs (Y, PB, PR) of the digital settop box to the C O M P O N E N T I N V I D E O jacks on
the TV. Match the jack colors (Y = green, PB = blue, and
PR = red).
2
1
2
Connect the audio output of the digital set-top box to
the C O M P O N E N T I N A U D I O jacks on the TV.
AV IN
VIDEO
USB IN
SERVICE ONLY
AUDIO
L(MONO) R
2
2. How to use
L
VIDEO
■
■
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box operation.)
Select the C o m p o n e n t input source on the TV using the
I N P U T button on the remote control.
AUDIO
1
COMPONENT IN
/DVI IN
Y, CB/PB, CR/PR
Supported Resolutions
32
R
Signal
Component
HDMI
480i
Yes
No
480p
Yes
Yes
720p
Yes
Yes
1080i
Yes
Yes
1080p
Yes
Yes
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480i
15.73
15.73
59.94
60.00
720x480p
31.47
31.50
59.94
60.00
1280x720p
44.96
45.00
59.94
60.00
1920x1080i
33.72
33.75
59.94
60.00
1920x1080p
26.97
27.00
33.71
33.75
67.432
67.50
23.976
24.00
29.97
30.00
59.94
60.00
HDMI Connection
1. How to connect
1
Connect the digital set-top box to the H D M I / D V I
I N or H D M I / D V I I N 1 / 2*// 3* jack on the TV.
AV IN
VIDEO
RGB IN (PC)
AUDIO
2
AUDIO IN
(RGB/DVI)
2
No separate audio connection is necessary.
HDMI supports both audio and video.
L
DEO
OPT
A
R
AUDIO
1
COMPONENT IN
/DVI IN
A
C
RS-232C IN
(CONTROL&SERVICE)
2. How to use
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
■ Select the H D M I or HDMI1/2*/
/ 3* input source on the TV
using the INPUT button on the remote control.
■
1
* HDMI 2: Except 19/22LH20, 22LH200C
* HDMI 3: Except 19/22/26/32/37/42LH20, 19/22LU55,
32CL20
EXTERNAL EQUIPMENT SETUP
L(MONO) R
HDMI OUTPUT
! NOTE
G
Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
HDMI-DTV
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480p
31.47
31.50
59.94
60.00
1280x720p
44.96
45.00
59.94
60.00
1920x1080i
33.72
33.75
59.94
60.00
1920x1080p
26.97
27.00
33.71
33.75
67.432
67.50
23.976
24.00
29.97
30.00
59.94
60.00
33
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
1. How to connect
EXTERNAL EQUIPMENT SETUP
1
Connect the DVI output of the digital set-top box to
the H D M I / D V I I N or H D M I / D V I I N 1 / 2* jack on
the TV.
AV IN
EO
RGB IN (PC)
AUDIO
L(MONO) R
AUDIO IN
(RGB/DVI)
OPTICAL DIGITA
AUDIO OUT
2
L
2
Connect the digital set-top box audio output to the
A U D I O I N ( R G B / D V I ) jack on the TV.
2. How to use
R
AUDIO
1
NT IN
/DVI IN
ANTENNA/
CABLE IN
RS-232C IN
(CONTROL&SERVICE)
1
2
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
■ Select the H D M I or HDMI1/2* input source on the TV
using the INPUT button on the remote control.
■
* HDMI 2: Except 19/22LH20, 22LH200C
DVI OUTPUT
L
R
AUDIO
! NOTE
G
34
A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio
connection is necessary.
DVD SETUP
Component Connection
1. How to connect
Y
2
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O jacks on the TV.
PB
PR
L
R
1
2
AV IN
VIDEO
USB IN
SERVICE ONLY
2. How to use
■
■
■
AUDIO
L(MONO) R
A
(
2
Turn on the DVD player, insert a DVD.
Select the C o m p o n e n t input source on the TV using the
I N P U T button on the remote control.
Refer to the DVD player's manual for operating instructions.
L
VIDEO
AUDIO
R
1
EXTERNAL EQUIPMENT SETUP
1
Connect the video outputs (Y, PB, PR) of the DVD to
the C O M P O N E N T I N V I D E O jacks on the TV. Match
the jack colors (Y = green, PB = blue, and PR = red).
COMPONENT IN
/DVI IN
Component Input ports
To get better picture quality, connect a DVD player to the
component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
Y
PB
PR
Y
PB
PR
Y
B-Y
R-Y
Y
Cb
Cr
Y
Pb
Pr
35
EXTERNAL EQUIPMENT SETUP
Composite (RCA) Connection
1. How to connect
EXTERNAL EQUIPMENT SETUP
1
V I D E O jacks between TV and
Connect the A U D I O/V
DVD. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red).
AV IN
VIDEO
USB IN
SERVICE ONLY
AUDIO
L(MONO) R
A
(
2
L
VIDEO
R
AUDIO
1
COMPONENT IN
2. How to use
■
■
■
/DVI IN
Turn on the DVD player, insert a DVD.
Select the A V or A V 1 / 2* input source on the TV using the
I N P U T button on the remote control.
Refer to the DVD player's manual for operating instructions.
1
* AV2: Only 32/37/42/47LH30, 26LU55,
32/37/42/47LF11, 47LF21
VIDEO
L
R
AUDIO
HDMI Connection
1. How to connect
AV IN
VIDEO
1
Connect the HDMI output of the DVD to the
H D M I / D V I I N or H D M I / D V I I N 1 / 2*// 3* jack
on the TV.
L(MONO) R
No separated audio connection is necessary.
HDMI supports both audio and video.
2. How to use
■
■
L
! NOTE
36
Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
OPTICAL
AUDIO
R
1
PONENT IN
/DVI IN
1
Select the HDMI or HDMI1 / 2*// 3* input source on the
TV using the I N P U T button on the remote control.
Refer to the DVD player's manual for operating instructions.
* HDMI 2: Except 19/22LH20, 22LH200C
* HDMI 3: Except 19/22/26/32/37/42LH20, 19/22LU55,
32CL20
G
AUDIO IN
(RGB/DVI)
2
AUDIO
2
RGB IN (PC)
AUDIO
HDMI OUTPUT
ANTEN
CABLE
RS-232C IN
(CONTROL&SERVICE)
VCR SETUP
Antenna Connection
1
Connect the RF antenna out socket of the
VCR to the A N T E N N A / C A B L E I N socket on the TV.
RGB IN (PC)
AUDIO IN
(RGB/DVI)
OPTICAL DIGITAL
AUDIO OUT
1
2
Connect the antenna cable to the RF
antenna in socket of the VCR.
IN
RS-232C IN
(CONTROL&SERVICE)
ANTENNA/
CABLE IN
ANT OUT
■
■
VIDEO
L
R
AUDIO
ANT IN
2
2. How to use
S-VIDEO
OUTPUT
SWITCH
Wall Jack
EXTERNAL EQUIPMENT SETUP
1. How to connect
Antenna
Set VCR output switch to 3 or 4 and then tune
TV to the same channel number.
Insert a video tape into the VCR and press PLAY
on the VCR. (Refer to the VCR owner’s manual.)
37
EXTERNAL EQUIPMENT SETUP
Composite (RCA) Connection
1. How to connect
EXTERNAL EQUIPMENT SETUP
1
V I D E O jacks between TV and
Connect the A U D I O/V
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red).
AV IN
VIDEO
USB IN
SERVICE ONLY
AUDIO
L(MONO) R
2
2. How to use
■
Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.)
■
Select the A V or A V 1 / 2* input source on the TV using
the I N P U T button on the remote control.
L
VIDEO
R
AUDIO
/DVI
1
* AV2: Only 32/37/42/47LH30, 26LU55,
32/37/42/47LF11, 47LF21
! NOTE
G
38
If you have a mono VCR, connect the audio cable from
the VCR to the A U D I O L / M O N O jack of the TV.
1
COMPONENT IN
ANT IN
S-VIDEO
VIDEO
L
R
AUDIO
ANT OUT
OUTPUT
SWITCH
OTHER A/V SOURCE SETUP
Camcorder
1. How to connect
V I D E O jacks
Connect the A U D I O/V
between TV and external equipment.
Match the jack colors.
(Video = yellow, Audio Left = white, and
Audio Right = red)
VIDEO
■
■
Select the A V 2* input source on the TV using
the I N P U T button on the remote control.
If connected to A V or A V I N 1 input, select
the A V or A V 1 input source on the TV.
Operate the corresponding external equipment.
* AV2: Only 32/37/42/47LH30, 26LU55,
32/37/42/47LF11, 47LF21
VIDEO L/MONO AUDIO R
■
IN 3
2. How to use
L
1
R
EXTERNAL EQUIPMENT SETUP
1
Video Game Set
AV IN 2
39
EXTERNAL EQUIPMENT SETUP
AUDIO OUT CONNECTION (Except 19/22LH20, 22LH200C)
Send the TV’s audio to external audio equipment via the Audio Output port.
If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL
AUDIO OUT terminal on the back of TV to a Home Theater (or amp).
EXTERNAL EQUIPMENT SETUP
1. How to connect
Connect one end of the optical cable to the TV port of
O P T I C A L D I G ITAL AUDIO OUT.
1
RGB IN (PC)
Connect the other end of the optical cable to the digital
audio input on the audio equipment.
2
AUDIO IN
(RGB/DVI)
2
1
1
/DVI IN
3
OPTICAL DIGITAL
AUDIO OUT
ANTENNA/
CABLE IN
RS-232C IN
(CONTROL&SERVICE)
Set the “TV Speaker option - Off ” in the AUDIO menu.
(G p .85). See the external audio equipment instruction
manual for operation.
2
! NOTE
G
When connecting with external audio equipments, such as
amplifiers or speakers, you can turn the TV speakers off in
the menu. (G p . 8 5)
CAUTION
G
G
40
Do not look into the optical output port. Looking at the
laser beam may damage your vision.
Audio with ACP (Audio Copy Protection) function may
block digital audio output.
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
VGA (D-Sub 15 pin) Connection
1
Connect the VGA output of the PC to the R G B I N
( P C) jack on the TV.
RGB IN (PC)
R
AUDIO IN
(RGB/DVI)
2
2
Connect the PC audio output to the A U D I O I N
( R G B / D V I) jack on the TV.
OPTICAL DIGITAL
AUDIO OUT
R
O
1
/DVI IN
ANTENNA/
CABLE IN
RS-232C IN
(CONTROL&SERVICE)
2. How to use
■
■
Turn on the PC and the TV.
Select the R G B - P C input source on the TV using the
I N P U T button on the remote control.
2
1
AUDIO
RGB OUTPUT
EXTERNAL EQUIPMENT SETUP
1. How to connect
41
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
1. How to connect
EXTERNAL EQUIPMENT SETUP
1
AV IN
Connect the DVI output of the PC to the H D M I / D V I
I N or H D M I / D V I I N 1 / 2* jack on the TV.
VIDEO
RGB IN (PC)
AUDIO
L(MONO) R
AUDIO IN
(RGB/DVI)
2
L
2
Connect the PC audio output to the A U D I O I N
( R G B / D V I ) jack on the TV.
2. How to use
■
■
DEO
R
AUDIO
1
OMPONENT IN
/DVI IN
1
AN
CA
RS-232C IN
(CONTROL&SERVICE)
2
Turn on the PC and the TV.
Select the HDMI or HDMI1 / 2* input source on the TV
using the I N P U T button on the remote control.
* HDMI 2: Except 19/22LH20, 22LH200C
! NOTE
DVI OUTPUT
G
42
Check HDMI cable over version 1.3.
If the HDMI cables don’t support HDMI version 1.3, it can
cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3.
OPTI
AU
AUDIO
! NOTES
19/22/26/32/37/42LH20, 22LH200C,
19/26LU55, 32CL20: To get the the best picture
quality, adjust the PC graphics card to 1360x768.
G
Avoid keeping a fixed image on the screen for a
long period of time. The fixed image may become
permanently imprinted on the screen.
G
32/37/42/47LH30, 22LU55, 32/37/42/47LF11,
47LF21: To get the the best picture quality, adjust
the PC graphics card to 1920x1080.
G
The synchronization input form for Horizontal and
Vertical frequencies is separate.
G
G
Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
Depending on the graphics card, some resolution
settings may not allow the image to be positioned
on the screen properly.
G
In PC mode, there may be noise associated with
the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to
another resolution, change the refresh rate to
another rate or adjust the brightness and contrast
on the PICTURE menu until the picture is clear.
G
If there are overscan in HDMI-PC 1920x1080,
change aspect ratio to J u s t s c a n.
G
When selecting HDMI-PC, set the “Input Label PC” in the OPTION menu.
Supported Display Specifications (RGB-PC, HDMI-PC)
For 19/22/26/32/37/42LH20, 22LH200C,
19/26LU55, 32CL20
For 32/37/42/47LH30, 22LU55,
32/37/42/47LF11, 47LF21
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
640x350
31.469
70.08
640x350
31.468
70.09
720x400
31.469
70.08
720x400
31.469
70.08
640x480
31.469
59.94
640x480
31.469
59.94
800x600
37.879
60.31
800x600
35.156
37.879
56.25
60.31
1024x768
48.363
60.00
1024x768
48.363
60.00
1280x768
47.776
59.87
1280x768
47.776
59.87
1360x768
47.712
60.015
1280x1024
63.981
60.02
1600x1200
75.00
60.00
66.587
59.934
67.5
60.00
1360x768
47.720
EXTERNAL EQUIPMENT SETUP
G
59.799
1920x1080
RGB-PC
1920x1080
HDMI-PC
43
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Selecting Resolution
PICTURE
• Contrast
50
• Brightness
50
• Sharpness
50
• Color
50
• Tint
SCREEN
Enter
0
Resolution
Auto Config.
Position
R
G
• Advanced Control
Size
• Picture Reset
Screen (RGB-PC)
Phase
Reset
1
MENU
2
Select P I C T U R E.
ENTER
Select S c r e e n ( R G B - P C ).
ENTER
Select R e s o l u t i o n.
3
4
ENTER
5
ENTER
44
Move
Move
E
EXTERNAL EQUIPMENT SETUP
You can choose the resolution in RGB-PC mode.
The P o s i t i o n, P h a s e, and S i z e can also be adjusted.
You can use this function only when the PC resolution is set to 1024X768, 1280X768 or 1360X768.
Select the desired resolution.
1024 x 768
1280 x 768
1360 x 768
Prev.
Auto Configure
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still
not correct, try using the manual settings or a different resolution or refresh rate on the PC.
Move
SCREEN
Enter
E
• Contrast
50
• Brightness
50
• Sharpness
50
• Color
50
• Tint
0
Move
Prev.
Resolution
Auto Config.
To Set
Position
R
G
• Advanced Control
• Picture Reset
Screen (RGB-PC)
Yes
Size
No
Phase
Reset
1
MENU
2
ENTER
Select P I C T U R E.
Select S c r e e n ( R G B - P C ).
■
■
3
ENTER
Select A u t o C o n f i g ..
ENTER
Select Y e s.
4
5
ENTER
EXTERNAL EQUIPMENT SETUP
PICTURE
If the position of the image is still not
correct, try Auto adjustment again.
If picture needs to be adjusted again
after Auto adjustment in RGB-PC, you
can adjust the P o s i t i o n , S i z e or
P h a s e.
Start Auto Configuration.
45
EXTERNAL EQUIPMENT SETUP
Adjustment for screen Position, Size, and Phase
PICTURE
Move
SCREEN
Enter
Move
Prev.
E
EXTERNAL EQUIPMENT SETUP
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture
phase manually.
This feature operates only in RGB-PC mode.
• Contrast
50
• Brightness
50
• Sharpness
50
• Color
50
• Tint
0
Resolution
Auto Config.
D
Position
R
F
G
• Advanced Control
G
E
Size
• Picture Reset
Screen (RGB-PC)
Phase
Reset
1
MENU
2
■
ENTER
Select S c r e e n ( R G B - P C ).
■
3
ENTER
Select P o s i t i o n, S i z e, or P h a s e.
■
4
ENTER
5
ENTER
46
Select P I C T U R E.
Make appropriate adjustments.
P o s i t i o n: This function is to adjust picture to left/right and up/down as you
prefer.
S i z e: This function is to minimize any
vertical bars or stripes visible on the
screen background. And the horizontal
screen size will also change.
P h a s e : This function allows you to
remove any horizontal noise and clear or
sharpen the image of characters.
Screen Reset (Reset to original factory values)
Returns P o s i t i o n, S i z e, and P h a s e to the default factory settings.
This feature operates only in RGB-PC mode.
Move
SCREEN
Enter
Move
Prev.
E
• Contrast
50
• Brightness
50
• Sharpness
50
• Color
50
• Tint
0
Resolution
Auto Config.
Position
R
To Set
G
• Advanced Control
Size
Yes
No
EXTERNAL EQUIPMENT SETUP
PICTURE
• Picture Reset
Screen (RGB-PC)
Phase
Reset
1
MENU
2
Select P I C T U R E.
ENTER
Select S c r e e n ( R G B - P C ).
ENTER
Select R e s e t.
3
4
ENTER
Select Y e s.
5
ENTER
47
WATCHING TV / CHANNEL CONTROL
REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
INFO
INFO Displays channel information at the top of the screen. G p.59
POWER
INPUT
ENERGY SAVING
AV MODE
AV MODE Toggles through preset Video and Audio modes. G p.62
WATCHING TV / CHANNEL CONTROL
POWER Turns the TV on from standby or off to standby.
INPUT Rotates through inputs.
Also switches the TV on from standby. G p.60
1
2
3
4
5
6
7
8
9
0
FLASHBK
ENERGY SAVING Adjusts the Energy Saving. G p.76
LIST
VOLUME UP Adjusts the volume.
/DOWN
MUTE Switches the sound on or off. G p.50
MUTE
CH
VOL
P
A
G
E
CHANNEL Changes the channel.
UP/DOWN
PAGE Moves from one full set of screen information to the next
UP/DOWN one.
ENTER
SIMPLINK Controls the SIMPLINK compatible devices.
Control buttons
Q.MENU Opens the list of Quick Menu options. G p.53
SIMPLINK See a list of AV devices connected to TV.
When you toggle this button, the SIMPLINK menu appears
at the screen. G p.64-65
FAV Scroll through the programmed Favorite channels. G p.58
MARK Select the input to apply the Picture Wizard settings. G p.69
48
MENU
RETURN
Q.MENU
MARK
FAV
NUMBER button
— (DASH) Used to enter a program number for multiple program channels such as 2-1, 2-2, etc.
FLASHBK Tunes to the last channel viewed.
THUMBSTICK Navigates the on-screen menus and adjusts the system settings to your preference.
(Up/Down/Left
Right/ENTER)
MENU Displays the main menu or clears all on-screen displays and return to TV viewing.
RETURN Allows the user to move return one step in an interactive application or other user interaction
function.
Installing Batteries
■
Open the battery compartment cover on the back side
and install the batteries matching correct polarity.
■
Install two 1.5V AAA batteries. Don’t mix old or used
batteries with new ones.
■
Close cover.
WATCHING TV / CHANNEL CONTROL
LIST Displays the channel table. G p.57
49
WATCHING TV / CHANNEL CONTROL
TURNING ON THE TV
First, connect power cord correctly.
And switch the AC power control switch on TV (Except 19/22LH20, 22LH200C, 32/37/42/47LF11, 47LF21, 32CL20).
At this moment, the TV switches to standby mode.
■ In standby mode to turn TV on, press the
) button on the TV or press the
, INPUT, C H (DE or
POWER, INPUT, CH ( or ), Number (0~9
9 ) button on the remote control.
1
2
WATCHING TV / CHANNEL CONTROL
Select the viewing source by using the INPUT button on the remote control.
This TV is programmed to remember which power state it was last set to, even if the power cord is out.
■
When finished using the TV, press the POWER button on the remote control. The TV reverts to standby
mode.
3
! NOTE
G
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
G
If you do not complete the I n i t i a l s e t t i n g, it will appear whenever the TV is switched on until the I n i t i a l
s e t t i n g procedure is completed.
G
If the TV is unplugged once or turn off with the AC power control switch on the TV, reset the C l o c k function.
CHANNEL SELECTION
1
Press the C H (
or
) or NUMBER buttons to select a channel number.
VOLUME ADJUSTMENT
Adjust the volume to suit your personal preference.
50
1
Press the V O L ( + or - ) button to adjust the volume.
2
If you want to switch the sound off, press the M U T E button.
3
You can cancel the Mute function by pressing the MUTE or V O L ( + or - )
button.
INITIAL SETTING
This Function guides the user to easily set the essential items for viewing the TV for the first time when purchasing the TV. It will be displayed on the screen when turning the TV on for the first time. It can also be activated from the user menus.
H o m e U s e”. We recommend setting the TV to “H
H o m e U s e” mode for the best picDefault selection is “H
ture in your home environment.
■ “S
S t o r e D e m o” Mode is only intended for use in retail environments. Customers can adjust the “P
Picture
menu - P i c t u r e m o d e” manually while inspecting the TV, but the TV will automatically return to preset instore mode after 5 minutes.
■ “S
S t o r e D e m o” Mode is an optimal setting for displaying at stores. “Store Demo” mode initializes the TV
to set the image quality.
■ You can also adjust I n i t i a l S e t t i n g in the O P T I O N menu.
■
Step3. Time setting
Language
Time Setting
English
Current Time Setting
Español
Month
Français
Previous
1
Next
F
Date
21
Year
2009
Hour
10 AM
10
Time Zone
Select Menu Language.
Eastern
Daylight Saving
Auto
Previous
1
G
02
Minute
ENTER
Auto
Next
WATCHING TV / CHANNEL CONTROL
Step1. Selecting Language
Select A u t o or M a n u a l.
Step2. Mode setting
2
Mode Setting
ENTER
Selecting the environment.
Choose the setting mode you want.
Store Demo
Home Use
Select [Home Use] to use this TV at home.
To use this TV at Store, select [Store Demo].
Previous
1
Select desired time
option.
Step4. Auto Tuning
Auto Tuning
Next
Before starting,
be sure that the
TV antenna is connected.
ENTER
Select H o m e U s e.
Previous
1
ENTER
INFO i Simple Manual
Next
Check your antenna connection and start
A u t o T u n i n g.
51
WATCHING TV / CHANNEL CONTROL
ON-SCREEN MENUS SELECTION
Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual.
CHANNEL
Move
Enter
PICTURE
Auto Tuning
Aspect Ratio
Manual Tuning
Picture Wizard
Move
AUDIO
Enter
: 16:9
Move
Auto Volume
Clear Voice II
Energy Saving : Off
Channel Edit
Picture Mode
Balance
WATCHING TV / CHANNEL CONTROL
Move
3
-
+
0
L
R
• Backlight
70
• Contrast
90
• SRS TruSurround XT: Off
• Brightness
50
• Treble
50
• Sharpness
70
• Bass
50
Sound Mode
E
TIME
: On
• Level
: Standard
Enter
: On
: Standard
E
Enter
Clock
Off Time
: Off
On Time
: Off
Sleep Timer
: Off
OPTION
Move
Enter
CHANNEL
PICTURE
AUDIO
TIME
OPTION
LOCK
LOCK
Move
Enter
Lock System
Menu Language
: English
Lock System
Audio Language
: English
Set Password
Set Password
: Off
: Off
Block Channel
Block Channel
SIMPLINK
: On
Movie Rating
TV Rating-English
Key Lock
: Off
TV Rating-Children
TV Rating-French
TV Rating-General
Downloadable Rating
Input Block
Input Label
Simple Manual
Caption
: Off
Downloadable Rating
Set ID
:1
Input Block
E
For USA
1
MENU
2
ENTER
3
ENTER
Display each menu.
Select a menu item.
Accept the current selection.
4
MENU
52
Return to TV viewing.
For Canada
QUICK MENU
Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual.
Q.Menu (Quick Menu) is a menu of features which users might use frequently.
Aspect Ratio
F
16:9
A
1
A s p e c t R a t i o: Selects your desired picture format.
P i c t u r e M o d e: Selects the factory preset picture
depend on the viewing environment.
S o u n d M o d e: Selects the factory preset sound for type
of program.
M u l t i A u d i o: Changes the audio language (Digital signal).
S A P: Selects MTS sound (Analog signal).
S l e e p T i m e r: Select the amount of time before your TV
turns off automatically.
D e l / A d d / F a v: Select channel you want to add/delete or
add the channel to the Favorite List.
C a p t i o n: Select on or off.
E n e r g y S a v i n g: Select the Energy Saving level to reduce
the TV’s power consumption by adjusting backlight.
WATCHING TV / CHANNEL CONTROL
A
G
Q.MENU
Display each menu.
2
Make appropriate adjustments.
3
Q.MENU
Return to TV viewing.
53
WATCHING TV / CHANNEL CONTROL
CHANNEL SETUP
Auto Scan (Auto Tuning)
Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the
channel list.
Run this function if you change your residence or move the TV. Also, make sure to run this function with the
antenna connected during TV broadcasting hours.
Auto Tuning memorizes only the channels available at the time.
WATCHING TV / CHANNEL CONTROL
CHANNEL
Move
Enter
Auto Tuning
Auto Tuning
Manual Tuning
Manual Tuning
Channel Edit
Channel Edit
Move
Enter
Check your antenna connection.
The previous channel information
will be updated during Auto
Tuning.
Yes
No
1
MENU
2
ENTER
Select C H A N N E L.
■
Select A u t o T u n i n g.
■
3
ENTER
4
ENTER
Select Y e s.
Run A u t o t u n i n g.
5
RETURN
MENU
54
CHANNEL
Return to the previous menu.
Return to TV viewing.
■
The TV will ask for a password if parental
control has been activated (LOCK
Menu). Use the password you set up in
the LOCK Menu to allow a channel
search.
When setting the Auto tuning or Manual
tuning, the number of maximum channel
you can store is 1000.
It is subject to change depending on the
broadcasting signal environment.
Memorizes all the available channels in
the order of DTV, TV, CADTV and CATV.
Add/Delete Channel (Manual Tuning)
When selecting DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the quality of the signal being received.
CHANNEL
Move
Enter
CHANNEL
Move
Auto Tuning
Manual Tuning
Manual Tuning
Channel Edit
Channel Edit
DTV
F
G
Select channel type and
RF-channel number.
Channel
2
DTV 2-1
Bad
Normal
Good
Delete
Close
1
Select C H A N N E L.
MENU
2
■
Select M a n u a l T u n i n g.
ENTER
3
■
ENTER
Select D T V, T V, C A D T V, or C A T V.
4
Select channel you want to add
or delete.
5
ENTER
The TV will ask for a password if parental
control has been activated (LOCK
Menu). Use the password you set up in
the LOCK Menu to allow a channel
search.
When setting the Auto tuning or Manual
tuning, the number of maximum channel
you can store is 1000.
It is subject to change depending on the
broadcasting signal environment.
WATCHING TV / CHANNEL CONTROL
Auto Tuning
Enter
Select A d d or D e l e t e.
6
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
55
WATCHING TV / CHANNEL CONTROL
Channel Editing
The channels in the Channel Edit List are displayed in black and the channels deleted from the Channel Edit
List are displayed in blue.
When a channel number is deleted, it means that you will be unable to select it using CH
button during TV
viewing.
If you wish to select the deleted channel, directly enter the channel number with the NUMBER buttons or select
it in the C h a n n e l E d i t menu.
WATCHING TV / CHANNEL CONTROL
CHANNEL
Move
Manual Tuning
Channel Edit
Ch. Change
Navigation
CH
Page Change
Previous
Add/Delete
1
MENU
2
ENTER
Select C H A N N E L.
Select C h a n n e l E d i t.
3
ENTER
Select a channel.
4
Add or delete the channel.
5
Return to the previous menu.
RETURN
Return to TV viewing.
MENU
56
Enter
Auto Tuning
■
■
Keep pressing the
button and use the
or
buttons to move between DTV,
TV, CADTV and CATV.
If the channel list is too long, use the C H
or
button to move between pages.
CHANNEL LIST
You can check which channels are stored in the memory by displaying the channel list.
Channel List
This padlock is displayed
when the channel is locked
with parental control.
DTV
2-1
DTV
3-1
DTV
4-1
Displaying Channel List
1
Display the C h a n n e l L i s t.
LIST
Selecting a channel in the channel list
1
2
WATCHING TV / CHANNEL CONTROL
Exit
Select a channel.
ENTER
Switch to the chosen channel number.
Paging through a channel list
1
CH
P
A
G
E
2
Turn the pages.
Return to TV viewing.
RETURN
57
WATCHING TV / CHANNEL CONTROL
FAVORITE CHANNEL SETUP
Favorite Channels are a convenient feature that lets you quickly select channels of your choice without waiting
for the TV to select all the in-between channels.
To tune to a favorite channel, press the F A V (Favorite) button repeatedly.
1
Del/Add/Fav
F
G
CH
P
A
G
E
or
1
2
3
4
5
6
7
8
9
Select your desired channel.
0
WATCHING TV / CHANNEL CONTROL
2
Q.MENU
Select D e l / A d d / F a v.
A
3
Favorite
Select F a v o r i t e.
4
Q.MENU
Return to TV viewing.
FAVORITE CHANNEL LIST
Displaying the favorite channel list
Favorite List
DTV
2-1
DTV
3-1
DTV
4-1
1
MARK
FAV
Display the Favorite channel list.
Selecting a channel in the favorite channel list
1
Exit
2
Select a channel.
ENTER
Switch to the chosen channel number.
Paging through a favorite channel list
1
CH
P
A
G
E
2
RETURN
58
Turn the pages.
Return to TV viewing.
BRIEF INFORMATION
Brief Info shows the present screen information.
1
INFO i
Show the Brief Info on the screen.
2
Return to TV viewing.
7
1
2
3
4
5
6
Brief Info Title Test..
DOLBY DIGITAL
CNN
CC
D
4:3
16:9
480i
480p
720p
1080i
1080p
Sat, Feb 21, 2009
Multilingual
10:40 AM
10:10 AM
D
CC
Caption
11:40 AM
1080i
TV-PG D L S V
Multilingual : The program contains two or more audio services. Use
the Q . M E N U menu to select wanted Audio.
1
Program title
2
Day, Month, Year
Caption : The program contains one or more caption services. Use
the Q . M E N U menu to select wanted Closed caption.
3
Program start time
4
Program progress bar
5
Program finish time
6
Present time
7
Banner information
D o l b y D i g i t a l: The program contains a Dolby Digital audio signal
in TV and HDMI input source.
WATCHING TV / CHANNEL CONTROL
RETURN
The original aspect ratio of the video is 4:3
The original aspect ratio of the video is 16:9 (wide)
The video resolution is 720x480i
The video resolution is 720x480p
The video resolution is 1280x720p
The video resolution is 1920x1080i
The video resolution is 1920x1080p
V - C h i p: The program contains V-Chip information. Refer to the
LOCK menu: A (Age), D (Dialogue), L (Language), S (Sex), V
(Violence), FV (Fantasy Violence)
59
WATCHING TV / CHANNEL CONTROL
INPUT LIST
Only these input signals which are connected to a TV can be activated and selected.
1
ENTER
INPUT
Select the desired input source.
19/22LH20,
22LH200C:
TV
AV
Component
HDMI
WATCHING TV / CHANNEL CONTROL
26/32/37/42LH20,
19/22LU55, 32CL20:
RGB-PC
TV
AV
Component
HDMI2
HDMI1
RGB-PC
TV
AV1
AV2
Component
HDMI3
HDMI2
HDMI1
RGB-PC
32/37/42/47LH30,
26LU55, 47LF21,
32/37/42/47LF11:
ie)
Disconnected inputs are inactive (grayed out)
TV
AV
Component
RGB-PC
HDMI1
Input Label
Exit
Select a desired input source (except T V).
Then, you can select your desired I n p u t
L a b e l with using Blue button. G p . 6 1
ie) In case of changing the input label using Blue button
VCR
TV
■
■
■
■
60
AV
DVD
Component
PC
Game
RGB-PC
HDMI1
When new external device is connected, this popup menu is
displayed automatically.
If selecting Y e s, you can select input source that you want to
appreciate.
S I M P L I N K - O n”, popup menu for HDMI
But, when selecting “S
input will not be displayed.
T V: Select it to watch over-the-air, cable and digital cable broadcasts.
A V: Select them to watch a VCR or other external
equipment.
■
■
■
!
New external input is connected.
Do you want to use this?
AV2
Yes
No
C o m p o n e n t: Select them to watch DVD or a
Digital set-top box.
R G B - P C: Select it to view PC input.
H D M I: Select them to watch high definition
devices.
INPUT LABEL
This indicates which device is connected to which input port.
OPTION
Move
Enter
Menu Language
: English
Audio Language
: English
Input Label
AV1
AV
F
G
RGB-PC
HDMI1
Simple Manual
RGB-PC
HDMI1
HDMI2
Caption
: Off
HDMI
HDMI2
HDMI3
Set ID
:1
Key Lock
: Off
AV
F
G
Close
Close
Close
19/22LH20,
22LH200C
26/32/37/42LH20,
19/22LU55, 32CL20
32/37/42/47LH30,
26LU55, 47LF21
32/37/42/47LF11
E
With using OPTION menu
With using INPUT button
1
1
Select O P T I O N.
INPUT
MENU
2
3
ENTER
Select I n p u t L a b e l.
ENTER
Select the source.
2
Select the source.
Select the label.
WATCHING TV / CHANNEL CONTROL
RGB-PC
Component
: On
G
Component
Component
SIMPLINK
F
AV2
3
RETURN
Return to the previous menu.
4
Select the label.
MENU
Return to TV viewing.
5
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
61
WATCHING TV / CHANNEL CONTROL
AV MODE
AV Mode toggles through preset Video and Audio settings.
Off
Cinema
Game
Sport
■
■
WATCHING TV / CHANNEL CONTROL
1
AV MODE
■
Press the A V M O D E button repeatedly to
select the desired source.
■
2
■
ENTER
■
C i n e m a” in AV mode,
If you select “C
C i n e m a will be selected both for “PICTURE menu - Picture Mode” and “AUDIO
menu - Sound Mode” respectively.
O f f” in AV mode, the
If you select “O
P i c t u r e M o d e” and “S
S o u n d M o d e”
“P
return to previous selected value.
O f f: Disables the AV MODE.
C i n e m a: Optimizes video and audio for
watching movies.
S p o r t: Optimizes video and audio for
watching sports events.
G a m e: Optimizes video and audio for
playing games.
SIMPLE MANUAL
You can easily and effectively access the TV information by viewing a simple manual on the TV.
During the Simple Manual operation, audio will be muted.
OPTION
Move
Menu Language
: English
Audio Language
: English
Enter
Input Label
SIMPLINK
: On
Key Lock
: Off
Simple Manual
Caption
: Off
Set ID
:1
E
3
1
Select O P T I O N.
ENTER
MENU
2
62
Select the part of the manual you
want to see.
4
ENTER
Select S i m p l e M a n u a l.
RETURN
Return to TV viewing.
KEY LOCK
The TV can be set up so that it can only be used with the remote control.
This feature can be used to prevent unauthorized viewing by locking out the front panel controls.
This TV is programmed to remember which option it was last set to even if you turn the TV off.
OPTION
Move
Enter
OPTION
Move
Menu Language
: English
Audio Language
: English
Audio Language
: English
Input Label
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: On
Simple Manual
Caption
Set ID
: Off
Caption
:1
Set ID
: Off
:1
E
MENU
2
ENTER
E
Select O P T I O N.
Select Key Lock.
■
3
ENTER
Select O n or O f f.
4
■
RETURN
MENU
Off
On
Simple Manual
WATCHING TV / CHANNEL CONTROL
: English
Input Label
1
Enter
Menu Language
Return to the previous menu.
Return to TV viewing.
O n’, if the TV is turned off,
In K e y L o c k ‘O
)
press the r / I, INPUT, CH (DE or
button on the TV or POWER, INPUT,
) or NUMBER buttons on the
CH (
remote control.
With the K e y L o c k O n, the display
‘ ! K e y L o c k’ appears on the screen if
any button on the front panel is pressed
while viewing the TV.
63
WATCHING TV / CHANNEL CONTROL
SIMPLINK allows you to control and play other AV devices connected with HDMI cable without additional
cables and settings. This TV may work with devices with HDMI-CEC support, but only devices with the
logo are fully supported.
SIMPLINK can be turned on and off in the user menus.
OPTION
Move
Enter
OPTION
Move
Enter
WATCHING TV / CHANNEL CONTROL
Menu Language
: English
Menu Language
: English
Audio Language
: English
Audio Language
: English
Input Label
Input Label
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Simple Manual
Off
On
Simple Manual
Caption
: Off
Caption
Set ID
:1
Set ID
E
: Off
:1
E
1
Select O P T I O N.
MENU
2
ENTER
Select S I M P L I N K.
ENTER
Select O n or O f f.
3
4
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
! NOTE
Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of the
SIMPLINK device with the HDMI cable.
G When you switch the Input source with the INPUT button on the remote control, the SIMPLINK device
will stop.
G When you select a device with home theater functionality, the sound output automatically switches to
the home theater speakers and the TV speakers are turned off.
G If a connected SIMPLINK home theater system doesn't play the audio from the TV, connect the DIGITAL
AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the back of the SIMPLINK device with an OPTICAL cable (Except 19/22LH20, 22LH200C).
G
64
SIMPLINK Functions
D i r e c t P l a y : After connecting AV devices to the TV, you can directly control the devices and play media without additional settings.
■ S e l e c t A V d e v i c e : Enables you to select one of the AV devices connected to TV.
■ D i s c p l a y b a c k : Control connected AV devices by pressing the
, ENTER, G, A, l l, FF and GG buttons.
■ P o w e r o f f a l l d e v i c e s : When you power off the TV, all connected devices are turned off.
■ S w i t c h a u d i o - o u t : Offers an easy way to switch audio-out.
■ S y n c P o w e r o n : When the equipment with Simplink function connected HDMI terminal starts to play, The TV
will change automatically to turn on mode.
(A device, which is connected to the TV through a HDMI cable but does not support SIMPLINK, does not provide
this function)
Note: To operate SIMPLINK, an HDMI cable over Version 1.3 with *CEC function should be used. (*CEC: Consumer
Electronics Control).
■
1
Display S I M P L I N K menu.
2
ENTER
WATCHING TV / CHANNEL CONTROL
SIMPLINK Menu
Select the desired device.
3
ENTER
1
2
3
4
5
Control connected AV devices.
T V v i e w i n g: Switch to the previous TV
channel regardless of the current mode.
D I S C p l a y b a c k: Select and play discs.
When multiple discs are available, the titles
of discs are conveniently displayed at the
bottom of the screen.
V C R p l a y b a c k: Control the connected
VCR.
H D D R e c o r d i n g s p l a y b a c k: Control
recordings stored in HDD.
A u d i o O u t t o H o m e T h e a t e r s p e a ke r / A u d i o O u t t o T V: Select Home
Theater speaker or TV speaker for Audio
Out.
1
2
G
3
4
G
G
5
When no device is connected
(displayed in gray)
Selected Device
When a device is connected
(displayed in bright color)
65
PICTURE CONTROL
PICTURE SIZE (ASPECT RATIO) CONTROL
This feature lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV.
HDMI/RGB-PC input source use 4:3 or 16:9 aspect ratio. But you can select all aspect ratios in HDMI-PC
1920X1080 input.
You can select a different aspect ratio depending on input source (analog broadcasting, digital broadcasting,
aux).
PICTURE
Move
Enter
PICTURE
Move
Aspect Ratio : 16:9
Aspect Ratio : 16:9
Picture Wizard
Picture Wizard
PICTURE CONTROL
Energy Saving : Off
Picture Mode
Energy Saving : Off
: Standard
Picture Mode
: Standard
16:9
• Backlight
70
• Backlight
70
Just Scan
• Contrast
90
• Contrast
90
Set By Program
• Brightness
50
• Brightness
50
4:3
• Sharpness
70
• Sharpness
70
Zoom
E
1
Enter
E
Cinema Zoom 1
Select P I C T U R E.
MENU
■
2
ENTER
Select A s p e c t R a t i o.
3
ENTER
Select the desired picture format.
4
RETURN
MENU
66
Return to the previous menu.
Return to TV viewing.
You can also adjust A s p e c t R a t i o in
the Q . M E N U.
4:3
Adjust the picture horizontally, in a linear proportion to fill the entire screen.
Choose 4:3 when you want to view a picture
with an original 4:3 aspect ratio.
Just Scan
Zoom
Normally the edges of video signals are cropped
1-2%. Just Scan turns off this cropping and
shows the complete video.
Notes: If there is noise on the edges of the original
signal, it will be visible when Just Scan is activated.
J u s t S c a n operates only in
DTV/CADTV/Component/HDMI-DTV/DVI-DTV
(720p/1080i/1080p) input source.
Choose Zoom when you want to view the picture
without any alteration. However, the top and
bottom portions of the picture will be cropped.
■
When adjusting in Q.MENU menu,
a.
or
button: Adjust proportion of Zoom.
b.
or button: Move the image on the screen.
PICTURE CONTROL
16:9
Just Scan
Cinema Zoom
Set By Program
Selects the proper picture proportion to match
the source’s image.
(4:3
4:3)
Set By Program
(16:9
Choose Cinema Zoom when you want to
enlarge the picture in correct proportion.
This enlarges an image with cinemascope aspect
ratio (2.35:1) without distortion.
Note: When enlarging or reducing the picture,
the image may become distorted.
or
button: Adjust proportion of
Cinema Zoom. The adjustment range is 1-16.
■
or
button: Move the image on the screen.
■
16:9)
Set By Program
67
PICTURE CONTROL
PICTURE WIZARD
This feature lets you adjust the picture quality of the original image.
Use this to calibrate the screen quality by adjusting the Black and White Level etc. You can calibrate the screen
quality by easily following each step.
When you adjust the image to L o w, R e c o m m e n d e d or H i g h, you can see the example of the changes you
made.
White Level
PICTURE
Move
Enter
Set the screen above identical to the Recommended sample
below.
Aspect Ratio : 16:9
Picture Wizard
Energy Saving : Off
: Standard
70
• Contrast
90
• Brightness
50
• Sharpness
70
Low
Recommended
• Contrast
90
High
E
PICTURE CONTROL
• Backlight
E
Picture Mode
E
Previous
1
Select P I C T U R E.
MENU
2
ENTER
ENTER
Select P i c t u r e
W i z a r d.
5
Next
ENTER
Adjust W h i t e L e v e l.
Color
Set the screen above identical to the Recommended sample
below.
Picture Wizard
With Picture Wizard, you can adjust the picture quality of the
original image.
• Color
50
High
E
G
Recommended
E
Low
Previous
Previous
3
Next
Next
6
ENTER
Adjust P i c t u r e W i z a r d.
ENTER
Adjust C o l o r.
Tint
Black Level
Set the screen above identical to the Recommended sample
below.
Set the screen above identical to the Recommended sample
below.
Low
Recommended
Recommended
0
R
G
E
E
50
E
• Tint
• Brightness
High
High
Previous
Previous
4
68
Next
Next
7
ENTER
E
Low
Adjust B l a c k L e v e l.
ENTER
Adjust T i n t.
e.g)
Complete
Horizontal Sharpness
Select (an) input(s) to apply the settings.
Set the screen above identical to the Recommended sample
below.
DTV
AV
Component
RGB-PC
Recommended
50
E
• H Sharpness
High
HDMI2
Next
Adjust H o r i z o n t a l
S h a r p n e s s.
Warning: The picture quality may vary according to the
different types of signal and inputs.
Previous
E
ENTER
E
Move
MARK
Mark
Confirm
Vertical Sharpness
Set the screen above identical to the Recommended sample
below.
Recommended
50
E
• V Sharpness
High
MARK
FAV
12
Previous
Save.
ENTER
Next
i
9
Select input source to apply the
settings.
E
Low
11
PICTURE CONTROL
Previous
8
HDMI1
E
Low
ENTER
Adjust V e r t i c a l
S h a r p n e s s.
The current adjustment value is saved to
Expert1.
Close
13
Finish the Picture Wizard.
ENTER
Backlight
Set the Backlight to your Brightness preference.
■
Recommended
Previous
10
50
E
• Backlight
Bright
E
Dark
Next
ENTER
■
If you stop the setting before the final
step, the changes will not be saved to
the TV.
Once the P i c t u r e W i z a r d sets the picture quality, E n e r g y S a v i n g is changed
to O f f automatically.
Adjust B a c k l i g h t.
69
PICTURE CONTROL
PRESET PICTURE SETTINGS (PICTURE MODE)
There are factory presets for picture settings available in the user menus. You can use a preset, change each
setting manually.
PICTURE
Move
Enter
PICTURE
Aspect Ratio : 16:9
Picture Wizard
Picture Wizard
Energy Saving : Off
Picture Mode
Enter
Energy Saving : Off
: Standard
Picture Mode
PICTURE CONTROL
: Standard
Vivid
• Backlight
70
• Backlight
70
Standard
• Contrast
90
• Contrast
90
Natural
• Brightness
50
• Brightness
50
Cinema
• Sharpness
70
• Sharpness
70
Sport
E
E
Game
Expert1
Expert2
1
Select P I C T U R E.
■
MENU
2
ENTER
Select P i c t u r e M o d e.
■
3
ENTER
Select V i v i d, S t a n d a r d, N a t u r a l,
C i n e m a, S p o r t, or G a m e.
■
4
RETURN
MENU
Return to the previous menu.
■
Return to TV viewing.
■
■
■
■
■
70
Move
Aspect Ratio : 16:9
V i v i d, S t a n d a r d, N a t u r a l, C i n e m a,
S p o r t, and G a m e Settings are preset for
the optimum picture quality at the factory.
V i v i d: This is the mode to maximize the
effect of the video in the retail store.
Strengthen the contrast, brightness,
color and sharpness for vivid picture.
S t a n d a r d: This is the mode to realize
optimum viewing condition for the general user.
N a t u r a l: This is the mode to display the
most natural screen status.
C i n e m a: This mode optimizes video for
watching movies.
S p o r t : This is the video mode to
emphasize dynamic video and primary
color (e.g, white, uniform, grass, sky blue
etc.) by realizing the optimal screen for
sports.
G a m e: This is the mode to realize fast
response speed in a fast gaming screen.
E x p e r t: This is the mode to adjust the
video in detail for video quality expert
and general user.
You can also adjust P i c t u r e M o d e in
the Q . M E N U.
MANUAL PICTURE ADJUSTMENT - USER MODE
Adjust the picture appearance to suit your preference and viewing situations.
PICTURE
Move
Aspect Ratio
Enter
: 16:9
Picture Wizard
70
• Contrast
90
50
• Sharpness
70
E
Enter
E
1
MENU
2
3
Select P I C T U R E.
■
■
ENTER
ENTER
4
ENTER
5
ENTER
Select P i c t u r e M o d e.
Select V i v i d, S t a n d a r d, N a t u r a l,
C i n e m a, S p o r t, or G a m e.
Select B a c k l i g h t, C o n t r a s t, B r i g h t n e s s,
S h a r p n e s s, C o l o r, or T i n t.
■
Make appropriate adjustments.
■
6
RETURN
Return to the previous menu.
■
MENU
Return to TV viewing.
■
■
When adjusting Energy Saving,
B a c k l i g h t function is disabled.
B a c k l i g h t: This function adjusts the
brightness of LCD panel, to control the
brightness of the screen. Adjusting the
backlight is recommended when setting
the brightness of the set. When decreasing the backlight, the brightness of the
black becomes darker without any loss in
video signal and the power consumption
is reduced.
C o n t r a s t: Increase or decrease the gradient of the video signal. You may use
Contrast when the bright part of picture
is saturated.
B r i g h t n e s s: Adjusts the base level of
the signal in the picture. You may use
Brightness when the dark part of the picture is saturated.
S h a r p n e s s: Adjusts the level of crispness in the edges between the light and
dark areas of the picture. The lower the
level, the softer the image.
C o l o r: Adjusts intensity of all colors.
T i n t: Adjusts the balance between red
and green levels.
PICTURE CONTROL
• Brightness
70
E
• Backlight
: Standard
• Backlight
E
E
Energy Saving : Off
Picture Mode
71
PICTURE CONTROL
PICTURE IMPROVEMENT TECHNOLOGY
You can calibrate the screen for each Picture Mode or set the video value according to the special video screen.
You can set the video seeing differently for each input.
To reset to the factory default after making adjustments to each input source, execute the P i c t u r e R e s e t
function for each P i c t u r e M o d e.
PICTURE
Move
PICTURE
Enter
Move
E
E
• Contrast
50
• Contrast
50
• Brightness
50
• Brightness
50
• Sharpness
50
• Sharpness
50
• Color
50
• Color
50
• Tint
0
R
• Tint
G
PICTURE CONTROL
• Advanced Control
0
Color Temperature
F
• Picture Reset
Screen (RGB-PC)
Off
Dynamic Color
Off
RNoise
G
Reduction
Off
Medium
Black Level
Low
Eye Care
Off
Real Cinema
Off
E
Close
Select P I C T U R E.
MENU
2
ENTER
Select A d v a n c e d C o n t r o l.
ENTER
Select your desired options.
3
4
Make appropriate adjustments.
5
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
Medium
Dynamic Contrast
• Advanced Control Gamma
• Picture Reset
Screen (RGB-PC)
1
72
Enter
G
EXPERT PICTURE CONTROL
By segmenting categories, E x p e r t 1 and E x p e r t 2 provide more categories which users can set as they see
fit, offering the optimal picture quality for users.
This may also be used be a professional to help optimize the TV performance in the environment the TV is in.
PICTURE
Move
:
Enter
PICTURE
16:9
Energy Saving: Off
:
Expert1
Enter
Dynamic Contrast
• Brightness
50
Noise Reduction
• H Sharpness 50
Gamma
• V Sharpness 50
Black Level
• Color
50
Picture Wizard
Picture Mode
Move
E
Aspect Ratio
Vivid
• Backlight
80Standard
• Contrast
90Natural
• Tint
• Brightness
50Cinema
• Expert Control Color Standard
• Picture Reset
• H Sharpness 50Sport
Screen (RGB-PC)
Game
Expert1
Expert2
MENU
Off
Off
G
SD
Color Gamut
Standard
Edge Enhancer
High
xvYCC
Auto
E
2
Select P I C T U R E.
ENTER
Select P i c t u r e M o d e.
ENTER
Select
ENTER
Select E x p e r t C o n t r o l.
ENTER
Select your desired menu option.
3
4
5
6
E x p e r t 1 or
G
Low
Close
1
Off
Low
PICTURE CONTROL
E
Real
0 R Cinema
F
E x p e r t 2.
Make appropriate adjustments.
7
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
73
PICTURE CONTROL
Color Temperature
Dynamic Contrast
■
Set to warm to enhance hotter colors such as red, or set to cool to make picture
bluish.
■
Adjusts the contrast to keep it at the best level according to the brightness of the
screen. The picture is improved by making bright parts brighter and dark parts darker.
■
Adjusts screen colors so that they look livelier, richer and clearer. This feature
enhances hue, saturation and luminance so that red, blue, green and white look
more vivid.
■
Reduces screen noise without compromising video quality.
Dynamic Color
Noise Reduction
PICTURE CONTROL
Gamma
Black Level
Low: The reflection of the screen gets darker.
High: The reflection of the screen gets brighter.
Auto: Realizing the black level of the screen and set it to High or Low automatically.
■ Set black level of the screen to proper level.
■ This function enables to select 'Low' or 'High' in the following mode: AV (NTSC-M),
HDMI or Component. Otherwise, 'Black level' is set to 'Auto'.
Eye Care
*This feature is not available for all models.
■ Adjust the brightness of the screen to prevent the screen from being too bright.
Dims extremely bright pictures.
■ This feature is disabled in “P
P i c t u r e M o d e - V i v i d, C i n e m a”.
Real Cinema
74
Low : Make dark and middle gray level area of the picture brighter.
Medium: Express original picture levels.
High: Make dark and middle gray level area of the picture darker.
■ You can adjust brightness of dark area and middle gray level area of the picture.
■
Makes video clips recorded in film look more natural by eliminating judder effect.
Color Gamut
Edge Enhancer
Color Standard
Color Filter
Expert Pattern
■
Show clearer and distinctive yet natural edges in of the video.
P i c t u r e M o d e - C i n e m a, E x p e r t".
This function is enabled in "P
■
Convert the color of a different video to HD color.
■
■
This is the function to filter the specific colors of the video.
You can use the RGB filter to set color saturation and hue accurately.
*This feature is not available for all models.
■ This is the function to express richer color.
■ This feature represents rich color as much as conventional video signal.
■ This function is enabled in "P
P i c t u r e m o d e - C i n e m a, E x p e r t" when xvYCC signal is inputted through HDMI.
■
■
This is the pattern necessary for expert adjustment.
P i c t u r e M o d e - E x p e r t" when you watch DTV.
This function is enabled in "P
Adjusts the overall color of the screen by changing the color of white.
a. Method : 2 Points
- Pattern: Inner, Outer
- Red/Green/Blue Contrast, Red/Green/Blue Brightness:
The adjustment range is -50 - +50.
b. Method : 10 Point IRE
- Pattern: Inner, Outer
- IRE (Institute of Radio Engineers) is the unit to display the size of the video signal
and can be set among 10, 20, 30 - 100. You can adjust Red, Green or Blue according to each setting.
- Luminance: This function displays calculated luminance value for 2.2 gamma. You can
input luminance value you want at 100 IRE, than the target luminance value for 2.2
gamma is displayed at every 10 steps from 10 IRE to 90 IRE.
- Red/Green/Blue: The adjustment range is -50 - +50.
■
White Balance
PICTURE CONTROL
xvYCC
Standard: Displays standard set of colors.
Wide: Increase number of colors used.
■ Maximize the utilization of color to increase color quality.
As the tool used by the experts to make adjustments by using the test patterns, this
does not affect other colors but can be used to selectively adjust the 6 color areas
(Red/Green/Blue/Cyan/Mgt/Yellow).
Color difference may not be distinctive even when you make the adjustments for the
general video.
Color Management System
Adjusts Red/Green/Blue/Yellow/Cyan, Magenta.
- Red/Green/Blue/Yellow/Cyan, Magenta Color: The adjustment range is -30 - +30.
- Red/Green/Blue/Yellow/Cyan, Magenta Tint: The adjustment range is -30 - +30.
- This feature is disable in RGB-PC and HDMI-PC mode.
■
OPC
*This feature is not available for all models.
■ As the technology to reduce the power consumption while keeping the same brightness, this has the effect of reducing power consumption, improvement in contrast.
75
PICTURE CONTROL
ENERGY SAVING
It reduces the TV’s power consumption by lowering the backlight level.
The default factory setting complies with the E n e r g y S t a r requirements and is adjusted to the comfortable
level to be viewed at home.
You can increase the brightness of your screen by adjusting the E n e r g y S a v i n g level or by setting the P i c t u r e
M o d e.
PICTURE
Aspect Ratio
Move
Enter
: 16:9
Aspect Ratio
Picture Wizard
Enter
Energy Saving : Off
PICTURE CONTROL
: Standard
Picture Mode
: Standard
• Backlight
70
• Backlight
• Contrast
90
• Contrast
• Brightness
50
• Brightness
• Sharpness
70
• Sharpness
E
E
70 Off
90 Minimum
50 Medium
70 Maximum
Screen off
1
MENU
2
3
Select P I C T U R E.
ENTER
Select
ENTER
Select O f f, M i n i m u m, M e d i u m,
M a x i m u m, or S c r e e n O f f.
E n e r g y S a v i n g.
RETURN
MENU
■
■
■
4
76
Move
: 16:9
Picture Wizard
Energy Saving : Off
Picture Mode
PICTURE
Return to the previous menu.
Return to TV viewing.
■
When selecting S c r e e n o f f, TV turned
off after 3 seconds.
If you adjust “EE n e r g y S a v i n g M i n i m u m , M e d i u m , M a x i m u m ”,
B a c k l i g h t feature will not work.
You can also adjust E n e r g y S a v i n g in
the Q . M E N U.
Press the E N E R G Y S A V I N G button
repeatedly to select the appropriate
Energy Saving setup.
PICTURE RESET
Settings of the selected picture modes return to the default factory settings.
PICTURE
Move
PICTURE
Enter
Move
E
E
• Contrast
50
• Contrast
50
• Brightness
50
• Brightness
50
• Sharpness
50
• Color
50
• Tint
• Tint
0
R
G
0 R
i Resetting video configuration...
• Advanced Control
G
Yes
No
• Picture Reset
Screen (RGB-PC)
MENU
2
3
Select P I C T U R E.
ENTER
Select P i c t u r e R e s e t.
ENTER
Select Y e s.
• Picture Reset
Screen (RGB-PC)
PICTURE CONTROL
• Sharpness
50 settings will be resetted.
? All picture
Continue?
• Color
50
• Advanced Control
1
Enter
4
ENTER
Initialize the adjusted value.
5
MENU
Return to TV viewing.
77
PICTURE CONTROL
POWER INDICATOR
- Except 19/22/26LH20, 22LH200C, 19/22/26LU55, 32/37/42/47LF11, 47LF21, 32CL20
Adjust the power/standby indicator light of TV front.
OPTION
Move
Enter
OPTION
Move
E
E
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Simple Manual
Simple Manual
Caption
: Off
Caption
: Off
Set ID
:1
Set ID
:1
Power Indicator
Power Indicator
Standby Light
PICTURE CONTROL
Demo Mode
: Off
Demo Mode
: Off
Initial Setting
: Home Use
Initial Setting
Power
: Home
Use Light
F
On
G
On
Close
1
Select O P T I O N.
■
ENTER
Select P o w e r I n d i c a t o r.
■
ENTER
Select S t a n d b y L i g h t or P o w e r L i g h t.
MENU
2
3
4
Select your desired options.
5
RETURN
MENU
78
Enter
Return to the previous menu.
Return to TV viewing.
S t a n d b y L i g h t: Determines whether to
set the indicator light on the front of the
TV to O n or O f f in standby mode.
P o w e r L i g h t: Determines whether to set
the indicator light on the front of the TV
to O n or O f f when the power turns on.
DEMO MODE
Displays a slide show to explain the various feature of this TV.
OPTION
Move
Enter
OPTION
Move
E
E
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Simple Manual
Simple Manual
Caption
: Off
Caption
: Off
Set ID
:1
Set ID
:1
Power Indicator
MENU
2
Power Indicator
: Off
Demo Mode
: On
Initial Setting
: Store Demo
Initial Setting
On
: Store Demo
Select O P T I O N.
ENTER
Select D e m o M o d e.
ENTER
Select O n to show the various
feature of the TV.
3
4
MENU
Off
Demo Mode
■
This feature is disabled in “II n i t i a l
S e t t i n g - H o m e U s e”.
PICTURE CONTROL
1
Enter
Return to TV viewing.
After a while, D e m o M o d e starts.
If you want to stop the demo, press any button
(Except VOL +, - and MUTE button).
79
SOUND & LANGUAGE CONTROL
AUTO VOLUME LEVELER (AUTO VOLUME)
Auto Volume makes sure that the volume level remains consistent whether you are watching a commercial or a
regular TV program.
Because each broadcasting station has its own signal conditions, volume adjustment may be needed every
time the channel is changed. This feature allows users to enjoy stable volume levels by making automatic
adjustments for each program.
AUDIO
Move
Auto Volume
: Off
Clear Voice II
: Off
• Level
Balance
Sound Mode
Enter
3
-
+
0
L
R
: Standard
SOUND & LANGUAGE CONTROL
MENU
80
On
• Level
Balance
3
-
+
0
L
R
: Standard
• SRS TruSurround XT: Off
• Treble
50
• Bass
50
• Bass
50
Select A u t o V o l u m e.
Select O n or O f f.
4
RETURN
: Off
50
3
ENTER
Clear Voice II
Return to the previous menu.
Return to TV viewing.
Enter
Off
• Treble
Select A U D I O.
ENTER
: On
• SRS TruSurround XT: Off
MENU
2
Move
Auto Volume
Sound Mode
E
1
AUDIO
E
CLEAR VOICE II
By differentiating the human sound range from others, it improves the sound quality of voices.
AUDIO
Move
Auto Volume
: Off
Clear Voice II
: Off
Clear Voice II
Balance
3
-
+
0
L
R
: Standard
MENU
Balance
3
-
0
L
On
+
R
: Standard
• SRS TruSurround XT: Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
E
Select A U D I O.
Select C l e a r V o i c e I I.
ENTER
Select O n or O f f.
3
Adjustment for Clear Voice Level
With selecting O n
ENTER
Select L e v e l.
ENTER
Make appropriate adjustments.
5
Off
: On
• SRS TruSurround XT: Off
ENTER
4
Enter
SOUND & LANGUAGE CONTROL
2
Move
: Off
• Level
Sound Mode
E
1
AUDIO
Auto Volume
• Level
Sound Mode
Enter
6
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
81
SOUND & LANGUAGE CONTROL
PRESET SOUND SETTINGS (SOUND MODE)
Sound Mode lets you enjoy the best sound without any special adjustment as the TV sets the appropriate
sound options based on the program content.
AUDIO
Move
Enter
AUDIO
Auto Volume
: Off
Auto Volume
: Off
Clear Voice II
: Off
Clear Voice II
: Off
• Level
Balance
Sound Mode
3
-
+
0
L
R
: Standard
• Level
Balance
Sound Mode
• Treble
50
• Bass
50
E
SOUND & LANGUAGE CONTROL
ENTER
Select A U D I O.
■
Select S o u n d M o d e.
■
■
3
ENTER
Select S t a n d a r d, M u s i c,
C i n e m a, S p o r t, or G a m e.
4
RETURN
Return to the previous menu.
■
■
■
MENU
82
L
+
Standard
R
Music
E
MENU
2
: Standard
3
0
Enter
Cinema
• SRS TruSurround XT: Off
Sport
• Treble
50
Game
• Bass
50
• SRS TruSurround XT: Off
1
Move
Return to TV viewing.
■
S t a n d a r d, M u s i c, C i n e m a, S p o r t,
and G a m e are preset for optimum
sound quality at the factory.
You can also adjust S o u n d M o d e in
the Q . M E N U.
S t a n d a r d : Offers standard-quality
sound.
M u s i c: Optimizes sound for listening to
music.
C i n e m a: Optimizes sound for watching
movies.
S p o r t: Optimizes sound for watching
sports events.
G a m e: Optimizes sound for playing
games.
SOUND SETTING ADJUSTMENT - USER MODE
Adjust the sound to suit your taste and room situations.
Move
Auto Volume
: Off
Clear Voice II
: Off
• Level
Balance
Sound Mode
Enter
3
-
+
0
L
R
: Standard
AUDIO
: Off
Clear Voice II
: Off
• Level
Balance
Sound Mode
50
• Bass
50
Select A U D I O.
5
Select S o u n d M o d e.
6
ENTER
RETURN
3
ENTER
4
ENTER
Select S t a n d a r d, M u s i c,
C i n e m a, S p o r t, or G a m e.
+
R
• SRS TruSurround XT
MENU
50
Off
50
Close
Make appropriate adjustments.
Return to the previous menu.
Return to TV viewing.
Select T r e b l e or B a s s.
SRS TRUSURROUND XT
SOUND & LANGUAGE CONTROL
ENTER
L
E
MENU
2
-
• SRS TruSurround XT: Off
• Treble
• Treble
50
• Bass
• Bass
50
E
1
: Standard
3
0
Enter
E
• SRS TruSurround XT: Off
• Treble
Move
Auto Volume
E
AUDIO
Select this option to sound realistic.
1
Select A U D I O.
MENU
2
■
ENTER
Select S R S T r u S u r r o u n d X T.
ENTER
Select O n or O f f.
3
■
■
4
RETURN
MENU
Return to the previous menu.
If sound quality or volume is not at the level
you want, it is recommended to use a separate
home theater system or amp to cope with different user environments.
C l e a r V o i c e I I - O n”, S R S
If you select “C
T r u S u r r o u n d X T feature will not work.
S R S T r u S u r r o u n d X T: TruSurround XT is a
patented SRS technology that solves the problem of playing 5.1 multichannel content over
two speakers.
Return to TV viewing.
83
SOUND & LANGUAGE CONTROL
BALANCE
Adjust the left/right sound of speaker to suit your taste and room situations.
Move
Auto Volume
: Off
Clear Voice II
: Off
• Level
Sound Mode
3
-
+
0
L
R
: Standard
SOUND & LANGUAGE CONTROL
MENU
84
• Level
Balance
3
-
+
0
L
Balance
R
• Treble
50
• Bass
50
• Bass
50
Select B a l a n c e.
Make appropriate adjustments.
Return to the previous menu.
Return to TV viewing.
0
: Standard
• SRS TruSurround XT: Off
4
RETURN
: Off
50
3
ENTER
Clear Voice II
Enter
• Treble
Select A U D I O.
ENTER
: Off
• SRS TruSurround XT: Off
MENU
2
Move
Auto Volume
Sound Mode
E
1
AUDIO
E
Balance
Enter
E
Close
L
R
E
AUDIO
TV SPEAKERS ON/OFF SETUP
Turn the TV speakers off if using external audio equipment.
In A V, C o m p o n e n t, R G B and H D M I with HDMI to DVI cable, the TV speaker can be operational even
when there is no video signal.
If you wish to use an external Hi-Fi system or a SRS System, turn off the TV’s internal speakers.
AUDIO
Move
Enter
AUDIO
E
Sound Mode
3
-
+
0
L
R
: Standard
• Level
Balance
Sound Mode
3
-
+
0
L
R
: Standard
• SRS TruSurround XT: Off
• SRS TruSurround XT: Off
• Treble
50
• Treble
50
• Bass
50
• Bass
50
• Reset
TV Speaker
Enter
E
• Level
Balance
Move
: On
• Reset
TV Speaker
: On
Off
On
MENU
2
Select A U D I O.
ENTER
Select T V S p e a k e r.
ENTER
Select O n or O f f.
3
SOUND & LANGUAGE CONTROL
1
4
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
85
SOUND & LANGUAGE CONTROL
AUDIO RESET
Settings of the selected Sound Mode return to the default factory settings.
AUDIO
Move
Enter
AUDIO
E
Sound Mode
3
+
0
L
R
: Standard
• Level
Balance
SOUND & LANGUAGE CONTROL
1
MENU
2
ENTER
Sound Mode
86
-
+
L
R
: Standard
• Treble
50
• Bass
50
• Treble
50
i Resetting audio configuration...
• Bass
50
: On
Select A U D I O.
Select R e s e t.
Initialize the adjusted value.
4
MENU
3
0
• SRS TruSurround XT: Off
3
ENTER
Enter
• SRS TruSurround XT: Off
• Reset
TV Speaker
Move
E
• Level
Balance
-
Return to TV viewing.
• Reset
TV Speaker
: On
STEREO/SAP BROADCAST SETUP
For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used
if the broadcast is only in Mono.
F
Multi Audio
G
English
A
1
Q.MENU
2
Digital TV
Select S A P.
Select M o n o, S t e r e o, or S A P.
3
Q.MENU
1
Q.MENU
2
Select M u l t i A u d i o.
Select other languages.
SOUND & LANGUAGE CONTROL
Analog TV
3
Return to TV viewing.
Q.MENU
Return to TV viewing.
87
SOUND & LANGUAGE CONTROL
AUDIO LANGUAGE
Other languages may be available if a digital signal is provided by the broadcasting station.
This feature operates only in DTV/CADTV mode.
OPTION
Move
Enter
: English
Audio Language
: English
Audio Language
: English
English
Input Label
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Simple Manual
Caption
: Off
Caption
Set ID
:1
Set ID
SOUND & LANGUAGE CONTROL
Select O P T I O N.
MENU
ENTER
Select A u d i o L a n g u a g e.
ENTER
Select your desired language.
3
4
MENU
88
Spanish
SIMPLINK
E
RETURN
Enter
Menu Language
Simple Manual
2
Move
: English
Input Label
1
OPTION
Menu Language
Return to the previous menu.
Return to TV viewing.
: Off
:1
E
French
ON-SCREEN MENUS LANGUAGE SELECTION
The menus can be shown on the screen in the selected language.
OPTION
Move
Enter
: English
Audio Language
: English
Audio Language
English
: English
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
3
ENTER
Simple Manual
Caption
: Off
Caption
Set ID
:1
Set ID
Select O P T I O N.
Select M e n u L a n g u a g e.
Select your desired language.
From this point on, the on-screen menus
will be shown in the selected language.
4
RETURN
MENU
Français
: Off
:1
E
SOUND & LANGUAGE CONTROL
ENTER
Español
Input Label
E
2
Enter
Menu Language
Simple Manual
MENU
Move
: English
Input Label
1
OPTION
Menu Language
Return to the previous menu.
Return to TV viewing.
89
SOUND & LANGUAGE CONTROL
CAPTION MODE
Analog Broadcasting System Captions
Captions are provided to help people with hearing loss watch TV. Select a caption mode for displaying captioning information if provided on a program. Analog caption displays information at any position on the screen
and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both
digital and analog channels on the Antenna/Cable. This TV is programmed to memorize the caption/text mode
which was last set when you turned the power off. This function is only available when C a p t i o n Mode is set O n.
OPTION
Move
Enter
Menu Language
: English
Audio Language
: English
Audio Language
: English
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Simple Manual
Caption
SOUND & LANGUAGE CONTROL
Set ID
: Off
Caption
:1
Set ID
: CC1
:1
E
E
F
Mode
On
G
CC1
Digital Option
Close
Select O P T I O N.
MENU
2
Enter
Input Label
Simple Manual
1
Move
: English
Input Label
ENTER
■
Select C a p t i o n.
■
3
ENTER
Select O n.
4
4 or T e x t 1-4
4.
Select C C 1-4
5
RETURN
MENU
90
OPTION
Menu Language
Return to the previous menu.
Return to TV viewing.
■
When selecting O f f, Sub-menus for
Analog, DTV, and Digital Option become
disabled.
CAPTION
The term for the words that scroll
across the bottom of the TV screen;
usually the audio portion of the program provided for the hearing impaired.
TEXT
The term for the words that appear in a
large black frame and almost cover the
entire screen; usually messages provided by the broadcaster.
Digital Broadcasting System Captions
Choose the language you want the DTV/CADTV Captions to appear in.
Other Languages can be chosen for digital sources only if they are included on the program.
This function in only available when Caption Mode is set On.
OPTION
Move
Enter
OPTION
Move
Enter
Menu Language
: English
Menu Language
: English
Audio Language
: English
Audio Language
: English
Input Label
Input Label
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Simple Manual
F
Simple Manual
Caption
Set ID
: Off
Caption
:1
Set ID
E
: CC1 Mode
:1
E
On
G
CC1
Digital Option
1
Select O P T I O N.
MENU
2
ENTER
Select C a p t i o n.
ENTER
Select O n.
3
4
SOUND & LANGUAGE CONTROL
Close
4 , T e x t 1-4
4 , or
Select C C 1-4
S e r v i c e 1 - 6.
5
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
91
SOUND & LANGUAGE CONTROL
Caption Option
Customize the DTV/CADTV captions that appear on your screen.
This function in only available when Caption Mode is set On.
OPTION
Move
Enter
Move
: English
Menu Language
: English
Audio Language
: English
Audio Language
: English
Input Label
SIMPLINK
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Mode
Simple Manual
Simple Manual
Caption
: Off
Caption
: CC1
Set ID
:1
Set ID
:1
SOUND & LANGUAGE CONTROL
E
Custom
G
Enter
Menu Language
Input Label
On
CC1
Digital Option
Close
E
Size
A Standard
Font
Font 1
Text Color
White
Text Opacity
Solid
Bg Color
Black
Bg Opacity
Solid
Edge Type
None
Edge Color
Black
Close
1
Select O P T I O N.
MENU
2
■
■
ENTER
Select C a p t i o n.
ENTER
Select O n.
3
■
■
■
4
Select D i g i t a l O p t i o n.
5
ENTER
6
Select C u s t o m.
Customize the S i z e, F o n t, etc., to your
preference. A preview icon is provided at
the bottom of the screen, use it to see the
caption language.
7
RETURN
MENU
92
F
OPTION
Return to the previous menu.
Return to TV viewing.
■
■
■
S i z e: Set the word size.
F o n t: Select a typeface for the text.
T e x t C o l o r: Choose a color for the
text.
T e x t O p a c i t y: Specify the opacity
for the text color.
B g ( B a c k g r o u n d ) C o l o r: Select a
background color.
B g ( B a c k g r o u n d ) O p a c i t y: Select
the opacity for the background color.
E d g e T y p e: Select an edge type.
E d g e C o l o r: Select a color for the
edges.
TIME SETTING
CLOCK SETTING
Auto Clock Setup
The time is set automatically from a digital channel signal.
The digital channel signal includes information for the current time provided by the broadcasting station.
Set the clock manually if the current time is set incorrectly by the auto clock function.
TIME
Move
Enter
Clock
TIME
Clock
Off Time
: Off
Off Time
On Time
: Off
On Time
Sleep Timer
: Off
Sleep Timer
Move
Enter
F
Auto
: Off Month
: Off
Date
: Off
Year
G
02
21
2009
Hour
10 AM
Minute
10
Eastern
Time Zone
Daylight
Saving
Auto
Close
Select T I M E.
MENU
2
ENTER
Select C l o c k.
ENTER
Select A u t o.
3
4
TIME SETTING
1
Select your viewing area time zone.
• U.S.A: E a s t e r n , C e n t r a l , M o u n t a i n ,
P a c i f i c, A l a s k a, or H a w a i i.
• Canada: E a s t e r n, C e n t r a l, M o u n t a i n,
P a c i f i c, N e w F . l a n d, or A t l a n t i c.
5
Select A u t o, O f f, or O n (depending on
whether or not your viewing area observes
Daylight Saving time).
6
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
93
TIME SETTING
Manual Clock Setup
If the current time setting is wrong, reset the clock manually.
If this TV is unplugged once or turn off with the AC power control switch on the TV, reset the C l o c k function.
TIME
Move
Enter
Clock
TIME
Move
Clock
Off Time
: Off
Off Time
Enter
F
: Off
Manual
Month
On Time
: Off
On Time
: Off
Sleep Timer
: Off
Sleep Timer
: Off Date
02
21
Year
2009
Hour
10 AM
Minute
10
Eastern
Time Zone
Daylight
Saving
Auto
Close
TIME SETTING
1
Select T I M E.
MENU
2
ENTER
Select C l o c k.
ENTER
Select M a n u a l.
3
4
Select the Year, Month, Date, Hour, or Minutes
option.
5
Set the Year, Month, Date, Hour, or Minutes
option.
6
RETURN
MENU
94
Return to the previous menu.
Return to TV viewing.
G
AUTO ON/OFF TIME SETTING
This function operates only if the current time has been set.
The O f f T i m e function overrides the O n T i m e function if they are both set to the same time.
The TV must be in standby mode for the O n T i m e to work.
If you do not press any button within 2 hours after the TV turns on with the O n T i m e function, the TV will
automatically revert to standby mode.
If you turn the TV off using the AC power control switch after setting O n T i m e, the O n T i m e function will
not work because the power is blocked.
TIME
Move
TIME
Enter
Clock
Move
Enter
Feb. 21, 2009 10:10 AM
Clock
Off Time
: Off
Off Time
: Off
Repeat
On Time
: Off
On Time
: 6:30 AM (Once)
Hour
Sleep Timer
: Off
Sleep Timer
: Off
Minute
F
Once
G
6 AM
30
Input
TV
Channel
TV 2-0
Volume
30
1
Select T I M E.
■
MENU
2
ENTER
■
Select O f f T i m e or O n T i m e.
To cancel O n / O f f T i m e function, select O f f.
Only for On Time function
1
2
3
ENTER
4
Select R e p e a t.
Select O f f, O n c e, D a i l y, M o n .~FF r i .,
M o n .~S
S a t ., S a t .~ S u n ., or S u n ..
3
4
5
Select and set H o u r or M i n u t e.
ENTER
TIME SETTING
Close
Select I n p u t.
Select the desired input source.
When Selecting T V:
set the channel at turn-on.
Adjust to sound level at
turn-on.
6
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
95
TIME SETTING
SLEEP TIMER SETTING
The Sleep Time turns the TV off at the preset time.
Note that this setting is cleared when the TV is turned off.
TIME
Move
Enter
Clock
TIME
Move
Enter
Clock
Off Time
: Off
Off Time
: Off
Off
On Time
: Off
On Time
: Off
10 min.
Sleep Timer
: Off
Sleep Timer
: Off
20 min.
30 min.
60 min.
90 min.
120 min.
180 min.
240 min.
1
Select T I M E.
TIME SETTING
MENU
2
■
ENTER
Select S l e e p T i m e r.
ENTER
Make appropriate adjustments.
3
4
RETURN
MENU
96
Return to the previous menu.
Return to TV viewing.
■
To cancel the S l e e p T i m e r, select O f f.
You can also adjust S l e e p T i m e r in
the Q . M E N U.
PARENTAL CONTROL / RATINGS
Parental Control can be used to block specific channels, ratings and other viewing sources.
The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the
type of the program and the categories. It is also possible to block all program viewing for a time period. To use
this function, the following must be done :
1. Set ratings and categories to be blocked.
2. Specify a password
3. Enable the lock
V-Chip rating and categories
Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be
blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-tovideo movies use the Movie Rating System (MPAA) only.
Ratings for Television programs including made-for-TV movies:
TV-G (General audience)
■ TV-PG (Parental guidance suggested)
■ TV-14 (Parents strongly cautioned)
■ TV-MA (Mature audience only)
(All children)
■ TV-Y
■ TV-Y7 (Children 7 years older)
■
Setting up Your Password
Set up blocking schemes to block specific channels, ratings, and external viewing sources.
A password is required to gain access to this menu.
For USA
For Canada
LOCK
Move
Lock System
Enter
: Off
LOCK
Lock System
Move
Enter Password
: Off
Set Password
Set Password
Block Channel
Block Channel
Movie Rating
TV Rating-English
TV Rating-Children
TV Rating-French
TV Rating-General
Downloadable Rating
Downloadable Rating
Input Block
Enter
*
*
*
*
PARENTAL CONTROL / RATING
SET PASSWORD & LOCK SYSTEM
Close
Input Block
1
ENTER
MENU
Select L O C K.
■
■
2
1
2
3
4
5
6
7
8
9
Enter the password as requested.
The TV is set up with the initial password
“0-0-0-0”.
Input the password.
0
97
PARENTAL CONTROL / RATINGS
Lock System
Enables or disables the blocking scheme you set up previously.
LOCK
Move
Lock System
1
2
1
2
3
4
5
6
7
8
9
Movie Rating
Movie Rating
TV Rating-Children
TV Rating-Children
TV Rating-General
TV Rating-General
Downloadable Rating
Downloadable Rating
Input Block
Input Block
Select L O C K.
Input the password.
PARENTAL CONTROL / RATING
Select O n or O f f.
5
MENU
98
Block Channel
4
RETURN
: On
Block Channel
Select L o c k S y s t e m.
ENTER
Move
Lock System
Set Password
0
3
LOCK
Set Password
ENTER
MENU
Enter
: Off
Return to the previous menu.
Return to TV viewing.
■
Enter
Off
On
When you select O n, the Lock System
is enable.
Set Password
Change the password by inputting a new password twice.
LOCK
Move
Lock System
1
2
2
3
4
5
6
7
8
9
Lock System
Block Channel
Block Channel
Movie Rating
Movie Rating
TV Rating-Children
TV Rating-Children
TV Rating-General
TV Rating-General
Downloadable Rating
Downloadable Rating
Input Block
Input Block
ENTER
1
2
3
4
5
6
7
8
9
Choose any 4 digits for your new password.
As soon as the 4 digits are entered, re-enter
the same 4 digits on the C o n f i r m.
5
MENU
*
*
*
*
Confirm
*
*
*
*
Close
Input the password.
0
RETURN
New
Select L O C K.
Select S e t P a s s w o r d.
4
Enter
: Off
Set Password
0
3
Move
Return to the previous menu.
PARENTAL CONTROL / RATING
1
: Off
LOCK
Set Password
ENTER
MENU
Enter
Return to TV viewing.
99
PARENTAL CONTROL / RATINGS
CHANNEL BLOCKING
Blocks any channels that you do not want to watch or that you do not want your children to watch.
LOCK
Move
Lock System
Enter
: Off
Set Password
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
Ch. Change
Navigation
CH
Page Change
Previous
Block/Unblock
1
ENTER
MENU
2
1
2
3
4
5
6
7
8
9
Select L O C K.
■
Input the password.
0
PARENTAL CONTROL / RATING
3
Select B l o c k C h a n n e l.
4
ENTER
5
Block or unblock a channel.
6
RETURN
MENU
100
Select a channel to block or unblock.
Return to the previous menu.
Return to TV viewing.
If a channel is locked, enter the password to unlocked it temporarily.
MOVIE & TV RATING
Movie Rating (MPAA) - For USA
Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can
set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that
the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.
LOCK
Move
Lock System
1
1
2
3
4
5
6
7
8
9
ENTER
MENU
Blocking off : Permits all programs
G
Block Channel
PG
Movie Rating
Movie Rating
PG-13
TV Rating-Children
TV Rating-Children
R
TV Rating-General
TV Rating-General
NC-17
Downloadable Rating
Downloadable Rating
X
Input Block
Input Block
Blocking Off
Select L O C K.
Input the password.
Select G , P G, P G - 1 3, R , N C - 1 7,
X , or B l o c k i n g O f f.
5
RETURN
: Off
Block Channel
Select M o v i e R a t i n g.
4
Lock System
Enter
Set Password
0
3
Move
Return to the previous menu.
If M o v i e R a t i n g , T V R a t i n g C h i l d r e n or T V R a t i n g - G e n e r a l is
locked, enter the password to unlocked
it temporarily.
■ G (General audience)
■ PG (Parental guidance suggested)
■ PG-13 (Parents strongly cautioned)
■ R (Restricted)
■ NC-17 (No one 17 and under admitted)
■ X (Adult only)
■ Blocking Off (Permits all programs)
G If you set PG-13: G and PG movies will
be available, PG-13, R, NC-17 and X will
be blocked.
■
PARENTAL CONTROL / RATING
2
: Off
LOCK
Set Password
ENTER
MENU
Enter
Return to TV viewing.
101
PARENTAL CONTROL / RATINGS
TV Rating Children - For USA
Prevents children from watching certain children's TV programs, according to the ratings limit set. The children
rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs.
LOCK
Move
Lock System
1
PARENTAL CONTROL / RATING
2
: Off
Lock System
2
3
4
5
6
7
8
9
Block Channel
Movie Rating
TV Rating-Children
TV Rating-Children
Age
TV Rating-General
TV Rating-General
Fantasy Violence
Downloadable Rating
Downloadable Rating
Input Block
Input Block
Select L O C K.
Input the password.
Select T V R a t i n g - C h i l d r e n.
4
ENTER
Select A g e or F a n t a s y V i o l e n c e.
ENTER
Select block options.
5
RETURN
MENU
: Off
Movie Rating
0
3
Enter
Block Channel
■
■
1
Move
Set Password
6
102
LOCK
Set Password
ENTER
MENU
Enter
Return to the previous menu.
Return to TV viewing.
Close
Age (applies to TV-Y, TV-Y7)
Fantasy Violence (applies to TV-Y7)
TV Rating General - For USA
Based on the ratings, blocks certain TV programs that you and your family do not want to view.
LOCK
Move
Lock System
Enter
: Off
LOCK
Move
Lock System
Enter
: Off
Set Password
Set Password
Block Channel
Block Channel
Age
Movie Rating
Movie Rating
Dialogue
TV Rating-Children
TV Rating-Children
Language
TV Rating-General
TV Rating-General
Sex
Downloadable Rating
Downloadable Rating
Violence
Input Block
Input Block
Close
1
ENTER
MENU
2
2
3
4
5
6
7
8
9
■
Input the password.
■
0
3
Select T V R a t i n g - G e n e r a l.
4
■
■
■
ENTER
Select A g e, D i a l o g u e, L a n g u a g e,
S e x or V i o l e n c e.
5
ENTER
Select block options.
Age (applies to TV-G,TV-PG,TV-14,TVMA).
Dialogue-sexual dialogue (applies to
TV-PG,TV-14).
Language-adult language (applies to
TV-PG, TV-14, TV-MA).
Sex-sexual situations (applies to TV-PG,
TV-14, TV-MA).
Violence (applies to TV-PG, TV-14, TVMA).
PARENTAL CONTROL / RATING
1
Select L O C K.
6
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
103
PARENTAL CONTROL / RATINGS
TV Rating English - For CANADA
Selecting Canadian English rating system.
LOCK
Move
Lock System
Enter
: Off
LOCK
Move
Lock System
: Off
Enter
Blocking off : Permits all programs
E
C
Set Password
Set Password
Block Channel
Block Channel
TV Rating-English
TV Rating-English
TV Rating-French
TV Rating-French
Downloadable Rating
Downloadable Rating
Input Block
Input Block
C8+
G
PG
14+
18+
Blocking Off
1
ENTER
MENU
2
PARENTAL CONTROL / RATING
1
2
3
4
5
6
7
8
9
■
Input the password.
0
3
■
Select T V R a t i n g - E n g l i s h.
■
■
4
ENTER
Select E , C , C 8 +, G , P G,
1 4 +, 1 8 +, or B l o c k i n g O f f.
■
■
5
■
RETURN
MENU
104
Select L O C K.
Return to the previous menu.
■
■
Return to TV viewing.
If T V R a t i n g - E n g l i s h or T V R a t i n g F r e n c h is locked, enter the password
to unlocked it temporarily.
E (Exempt)
C (Children)
C8+ (Children eight years and older)
G (General programming, suitable for
all audiences)
PG (Parental Guidance)
14+ (Viewers 14 years and older)
18+ (Adult programming)
Blocking Off (Permits all programs)
TV Rating French - For CANADA
Selecting Canadian French rating system.
LOCK
Move
Lock System
Enter
: Off
LOCK
Move
Lock System
: Off
Enter
Blocking off : Permits all programs
E
Set Password
Set Password
G
Block Channel
Block Channel
8ans+
TV Rating-English
TV Rating-English
13ans+
TV Rating-French
TV Rating-French
16ans+
Downloadable Rating
Downloadable Rating
18ans+
Input Block
Input Block
Blocking Off
1
ENTER
MENU
Select L O C K.
■
■
2
2
3
4
5
6
7
8
9
■
Input the password.
■
0
3
Select T V R a t i n g - F r e n c h.
4
■
■
ENTER
Select E , G , 8 a n s +, 1 3 a n s +,
1 6 a n s +, 1 8 a n s +, or B l o c k i n g o f f.
5
RETURN
MENU
Return to the previous menu.
■
PARENTAL CONTROL / RATING
1
E (Exempt)
G (General)
8ans+ (General-Not convenient for little children)
13ans+ (Not convenient for children of
13 years and younger)
16ans+ (Not convenient for children of
16 years and younger)
18ans+ (This programs is only for
adults)
Blocking off (Permits all programs)
Return to TV viewing.
105
PARENTAL CONTROL / RATINGS
DOWNLOADABLE RATING
This function is available only for digital channels.
This function operates only when TV has received Region5 Rating data.
LOCK
Move
Enter
LOCK
Move
Enter
E
Lock System
: Off
Lock System
: Off
Set Password
Set Password
Block Channel
Block Channel
Movie Rating
Movie Rating
TV Rating-Children
TV Rating-Children
TV Rating-General
TV Rating-General
Downloadable Rating
Downloadable Rating
Input Block
Input Block
Humor
Sport
Cruelty
Language
Sadness
Genre
Age
E
Close
PARENTAL CONTROL / RATING
1
ENTER
MENU
2
1
2
3
4
5
6
7
8
9
Select L O C K.
Input the password.
0
3
Select D o w n l o a d a b l e R a t i n g.
4
ENTER
Select desired D o w n l o a d a b l e
R a t i n g option.
ENTER
Select desired option and block it.
5
6
RETURN
MENU
106
Return to the previous menu.
Return to TV viewing.
■
Based on rating table, your TV's OSD
(On Screen Display) may differ slightly
from what is shown in this manual.
■
If a Downloadable rating is locked,
enter the password to unlocked it
temporarily.
EXTERNAL INPUT BLOCKING
Enables you to block an input.
LOCK
Move
Lock System
Enter
: Off
AV1
Set Password
AV
Block Channel
Movie Rating
TV Rating-Children
TV Rating-General
Downloadable Rating
Input Block
AV
F
Off
Component
Off
RGB-PC
Off
HDMI
Off
Close
19/22LH20,
22LH200C
1
ENTER
MENU
1
2
3
4
5
6
8
9
7
Input the password.
Select I n p u t B l o c k.
4
ENTER
5
Off
HDMI1
Off
HDMI2
Off
RGB-PC
Off
HDMI1
Off
HDMI2
Off
HDMI3
Off
G
Off
RGB-PC
Component
G
Off
Close
26/32/37/42LH20,
19/22LU55, 32CL20
Close
32/37/42/47LH30,
26LU55, 47LF21
32/37/42/47LF11
Select L O C K.
0
3
Off
Off
Off
Select input source.
Select O n or O f f.
PARENTAL CONTROL / RATING
2
F
Component
G
F
AV2
6
RETURN
MENU
Return to the previous menu.
Return to TV viewing.
107
APPENDIX
TROUBLESHOOTING
The operation does not work normally.
Check to see if there is any object between the product and the remote control
causing obstruction. Ensure you are pointing the remote control directly at the TV.
■ Ensure that the batteries are installed with correct polarity (+ to +, - to -).
■ Ensure that the correct remote operating mode is set: TV, VCR etc.
■ Install new batteries.
■
The remote control
doesn’t work
*This feature is not available for all models.
Power is suddenly
turned off
Is the sleep timer set?
Check the power control settings. Power interrupted.
■ TV will be automatically turned off, in case of no signal for 15 minutes.
■
■
The video does not work.
Check whether the product is turned on.
Try another channel. The problem may be with the broadcast.
■ Is the power cord inserted into wall power outlet?
■ Check your antenna direction and/or location.
■ Test the wall power outlet, plug another product’s power cord into the outlet
where the product’s power cord was plugged in.
■
■
No picture &No sound
Picture appears slowly
after switching on
■
This is normal, the image is muted during the product startup process. Please
contact your service center, if the picture has not appeared after five minutes.
APPENDIX
Adjust Color in menu option.
■ Keep a sufficient distance between the product and the VCR.
■ Try another channel. The problem may be with the broadcast.
■ Are the video cables installed properly?
■ Activate any function to restore the brightness of the picture.
■
No or poor color
or poor picture
Horizontal/vertical bars
or picture shaking
■
Check for local interference such as an electrical appliance or power tool.
Station or cable product experiencing problems, tune to another station.
Station signal is weak, reorient antenna to receive weaker station.
■ Check for sources of possible interference.
■
Poor reception on
some channels
Lines or streaks
in pictures
No picture
when connecting HDMI
108
■
■
Check antenna (Change the direction of the antenna).
■
Check HDMI cable over version 1.3.
The HDMI cables don’t support HDMI version 1.3, it cause flickers or no screen
display. In this case use the latest cables that support HDMI version 1.3.
The audio does not work.
Press the VOL or VOLUME button.
Sound muted? Press MUTE button.
■ Try another channel. The problem may be with the broadcast.
■ Are the audio cables installed properly?
■
■
Picture OK & No sound
No output from one
of the speakers
■
Adjust Balance in menu option.
■
A change in ambient humidity or temperature may result in an unusual noise
when the product is turned on or off and does not indicate a fault with the
product.
Unusual sound from
inside the product
No sound
when connecting HDMI
or USB
Check HDMI cable over version 1.3.
Check USB cable over version 2.0.
■ Use normal MP3 file.
■
■
*This feature is not available for all models.
There is a problem in PC mode. (Only PC mode applied)
The signal is out of range
Screen color is unstable
or single color
■
Work the Auto configure or adjust clock, phase, or H/V position. (Option)
APPENDIX
Vertical bar or stripe on
background &
Horizontal Noise &
Incorrect position
Adjust resolution, horizontal frequency, or vertical frequency.
■ Check the input source.
■
Check the signal cable.
■ Reinstall the PC video card.
■
109
APPENDIX
MAINTENANCE
Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can
enjoy your new TV.
Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.
Cleaning the Screen
Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm
water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then
use it to wipe the screen.
1
2
Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.
Cleaning the Cabinet
To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.
■ Please be sure not to use a wet cloth.
■
Extended Absence
CAUTION
G
APPENDIX
110
If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug
the power cord to protect against possible damage from lightning or power surges.
PRODUCT SPECIFICATIONS
MODELS
22LH20 (22LH20-UA)
22LH200C (22LH200C-UA)
Dimensions
(Width x Height
x Depth)
With stand
18.2 x 13.8 x 6.7 inches
462.4 x 353.0 x 171.0 mm
21.0 x 15.6 x 6.7 inches
533.4 x 397.0 x 171.0 mm
Without stand
18.2 x 12.1 x 2.5 inches
462.4 x 308.0 x 65.0 mm
21.0 x 13.8 x 2.5 inches
533.4 x 351.4 x 65.0 mm
Weight
With stand
Without stand
8.3 lbs / 3.8 kg
7.9 lbs / 3.6 kg
10.5 lbs / 4.8 kg
10.1 lbs / 4.6 kg
26LH20
(26LH20-UA)
32LH20
(32LH20-UA)
MODELS
Dimensions
(Width x Height
x Depth)
With stand
26.2 x 19.8 x 8.8 inches
667.0 x 504.0 x 224.0 mm
31.6 x 22.9 x 8.8 inches
805.0 x 583.0 x 224.0 mm
Without stand
26.2 x 17.5 x 3.1 inches
667.0 x 446.2 x 80.0 mm
31.6 x 20.7 x 3.1 inches
805.0 x 528.0 x 79.9 mm
Weight
With stand
Without stand
19.6 lbs / 8.9 kg
17.1 lbs / 7.8 kg
25.3 lbs / 11.5 kg
22.7 lbs / 10.3 kg
37LH20
(37LH20-UA)
42LH20
(42LH20-UA)
MODELS
With stand
36.2 x 25.9 x 11.6 inches
922.0 x 659.0 x 297.0 mm
40.4 x 28.1 x 11.6 inches
1028.0 x 715.4 x 297.0 mm
Without stand
36.2 x 23.4 x 3.4 inches
922.0 x 595.0 x 88.0 mm
40.4 x 25.7 x 3.4 inches
1028.0 x 655.0 x 88.7 mm
Weight
With stand
Without stand
32.6 lbs / 14.8 kg
28.6 lbs / 13.0 kg
39.6 lbs / 18.0 kg
35.7 lbs / 16.2 kg
Environment
condition
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
APPENDIX
Dimensions
(Width x Height
x Depth)
Power requirement
Television System
Program Coverage
External Antenna Impedance
■
19LH20
(19LH20-UA)
AC100-240V ~ 50/60Hz
NTSC-M, ATSC, 64 & 256 QAM
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
75 ohm
32 ~ 104°F (0 ~ 40°C)
Less than 80%
-4 ~ 140°F (-20 ~ 60°C)
Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.
111
APPENDIX
MODELS
With stand
31.6 x 22.9 x 8.8 inches
805.0 x 583.0 x 224.0 mm
36.2 x 25.9 x 11.6 inches
922.0 x 659.0 x 297.0 mm
Without stand
31.6 x 20.9 x 3.1 inches
805.0 x 531.0 x 79.9 mm
36.2 x 23.4 x 3.4 inches
922.0 x 595.0 x 88.0 mm
Weight
With stand
Without stand
26.6 lbs / 12.1 kg
24.2 lbs / 11.0 kg
32.8 lbs / 14.9 kg
28.8 lbs / 13.1 kg
42LH30
(42LH30-UA)
47LH30
(47LH30-UA)
Dimensions
(Width x Height
x Depth)
With stand
40.4 x 28.1 x 11.6 inches
1028.0 x 715.4 x 297.0 mm
44.9 x 30.8 x 13.2 inches
1140.6 x 784.8 x 337.4 mm
Without stand
40.4 x 25.9 x 3.4 inches
1028.0 x 658.6 x 88.7 mm
44.9 x 28.4 x 3.8 inches
1140.6 x 722.9 x 99.0 mm
Weight
With stand
Without stand
39.6 lbs / 18.0 kg
35.7 lbs / 16.2 kg
49.6 lbs / 22.5 kg
43.8 lbs / 19.9 kg
APPENDIX
Power requirement
Television System
Program Coverage
External Antenna Impedance
Environment
condition
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
112
37LH30
(37LH30-UA)
Dimensions
(Width x Height
x Depth)
MODELS
■
32LH30
(32LH30-UA)
AC100-240V ~ 50/60Hz
NTSC-M, ATSC, 64 & 256 QAM
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
75 ohm
32 ~ 104°F (0 ~ 40°C)
Less than 80%
-4 ~ 140°F (-20 ~ 60°C)
Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.
MODELS
22LU55
(22LU55-UB)
Dimensions
(Width x Height
x Depth)
With stand
18.1 x 14.6 x 7.1 inches
462.0 x 373.0 x 182.0 mm
20.8 x 16.4 x 7.7 inches
529.1 x 416.6 x 196.0 mm
Without stand
18.1 x 12.0 x 2.5 inches
462.0 x 305.0 x 65.0 mm
20.8 x 13.4 x 2.5 inches
529.1 x 342.3 x 65.0 mm
Weight
With stand
Without stand
9.7 lbs / 4.4 kg
8.1 lbs / 3.7 kg
11.9 lbs / 5.4 kg
10.1 lbs / 4.6 kg
26LU55
(26LU55-UB)
32CL20
(32CL20-UA)
MODELS
Dimensions
(Width x Height
x Depth)
With stand
26.2 x 21.1 x 9.2 inches
668.0 x 538.3 x 236.0 mm
32.0 x 23.5 x 9.1 inches
813.8 x 598.8 x 231.9 mm
Without stand
26.2 x 17.9 x 3.1 inches
668.0 x 456.0 x 81.0 mm
32.0 x 21.2 x 3.1 inches
813.8 x 540.4 x 78.9 mm
Weight
With stand
Without stand
19.6 lbs / 8.9 kg
16.9 lbs / 7.7 kg
26.8 lbs / 12.2 kg
23.3 lbs / 10.6 kg
Environment
condition
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
AC100-240V ~ 50/60Hz
NTSC-M, ATSC, 64 & 256 QAM
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
75 ohm
32 ~ 104°F (0 ~ 40°C)
Less than 80%
APPENDIX
Power requirement
Television System
Program Coverage
External Antenna Impedance
■
19LU55
(19LU55-UB)
-4 ~ 140°F (-20 ~ 60°C)
Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.
113
APPENDIX
MODELS
With stand
31.5 x 23.7 x 8.9 inches
801.8 x 604.2 x 227.3 mm
36.2 x 26.8 x 11.5 inches
919.6 x 682.3 x 293.8 mm
Without stand
31.5 x 21.4 x 3.1 inches
801.8 x 544.1 x 79.0 mm
36.2 x 24.0 x 3.5 inches
919.6 x 610.3 x 89.0 mm
Weight
With stand
Without stand
26.4 lbs / 12.0 kg
23.1 lbs / 10.5 kg
35.4 lbs / 16.1 kg
29.5 lbs / 13.4 kg
42LF11
(42LF11-UA)
47LF11 (47LF11-UA)
47LF21 (47LF21-UA)
Dimensions
(Width x Height
x Depth)
With stand
40.6 x 29.2 x 11.5 inches
1032.8 x 742.3 x 293.8 mm
45.1 x 31.7 x 13.5 inches
1146.0 x 805.8 x 342.9 mm
Without stand
40.6 x 26.3 x 3.6 inches
1032.8 x 670.1 x 92.0 mm
45.1 x 28.8 x 4.0 inches
1146.0 x 732.8 x 103.0 mm
Weight
With stand
Without stand
44.9 lbs / 20.4 kg
39.0 lbs / 17.7 kg
60.6 lbs / 27.5 kg
50.4 lbs / 22.9 kg
Power requirement
Television System
Program Coverage
External Antenna Impedance
APPENDIX
114
37LF11
(37LF11-UA)
Dimensions
(Width x Height
x Depth)
MODELS
Environment
condition
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
■
32LF11
(32LF11-UA)
AC100-240V ~ 50/60Hz
NTSC-M, ATSC, 64 & 256 QAM
VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135
75 ohm
32 ~ 104°F (0 ~ 40°C)
Less than 80%
-4 ~ 140°F (-20 ~ 60°C)
Less than 85%
The specifications shown above may be changed without prior notice for quality improvement.
IR CODES
(Hexa)
Code
Function
Note
08
POWER
Remote control Button (Power On/Off) D6
45
Q.MENU
Remote control Button
43
MENU
Remote control Button
0B
INPUT
Remote control Button
10-19
Number Key 0-9
Remote control Button
4C
- (Dash)/LIST
Remote control Button
1A
FLASHBK
Remote control Button
09
MUTE
Remote control Button
02
VOL +
Remote control Button
03
VOL -
Remote control Button
00
CH
Remote control Button
01
CH
Remote control Button
1E
FAV/MARK
Remote control Button
40
Remote control Button
41
Remote control Button
07
Remote control Button
06
Remote control Button
ENTER
Remote control Button
28
RETURN
Remote control Button
95
ENERGY SAVING
Remote control Button
7E
SIMPLINK
Remote control Button
AA
INFO
Remote control Button
30
AV MODE
Remote control Button
72
RED
Remote control Button
71
GREEN (A)
Remote control Button
63
YELLOW (G)
Remote control Button
61
BLUE (l l)
Remote control Button
8F
FF
Remote control Button
8E
GG
Remote control Button
Function
TV
Note
Discrete IR Code
(TV Input Selection)
C4
POWER ON
Discrete IR Code
(Only Power On)
C5
POWER OFF
Discrete IR Code
(Only Power Off)
5A
AV or AV1
Discrete IR Code
(AV or AV1 Input Selection)
D0
AV2
Discrete IR Code
(AV2 Input Selection)
BF
COMPONENT
Discrete IR Code
(Component Input Selection)
D5
RGB-PC
Discrete IR Code
(RGB-PC Input Selection)
CE
HDMI or HDMI1
Discrete IR Code
(HDMI or HDMI1 Input Selection)
CC
HDMI2
E9
HDMI3
Discrete IR Code
(HDMI2 Input Selection)
Discrete IR Code
(HDMI3 Input Selection)
76
Ratio 4:3
Discrete IR Code
(Only 4:3 Mode)
77
Ratio 16:9
Discrete IR Code
(Only 16:9 Mode)
AF
Ratio Zoom
APPENDIX
44
Code
(Hexa)
Discrete IR Code
(Only Zoom Mode)
* Use this feature depending on your model.
115
APPENDIX
EXTERNAL CONTROL THROUGH RS-232C
The RS-232C port allows you connect the RS-232C input jack to an external control device (such as a computer
or an A/V control system) to control the TV’s functions externally.
■ Note: RS-232C on this unit is intended to be used with third party RS-232C control hardware and software.
The instructions below are provided to help with programming software or to test functionality using telenet
software.
RS-232C Setup
i.e)
AV IN
EO
RGB IN (PC)
AUDIO
L(MONO) R
AUDIO IN
(RGB/DVI)
2
L
OPTICAL DIGITAL
AUDIO OUT
R
AUDIO
/DVI IN
ANTENNA/
CABLE IN
RS-232C IN
(CONTROL&SERVICE)
Type of Connector; D-Sub 9-Pin Male
APPENDIX
116
PC
1
ENT IN
No.
Pin Name
1
2
3
4
5
6
7
8
9
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
Communication Parameters
Baud rate : 9600 bps (UART)
■ Data length : 8 bits
■ Parity : None
■ Stop bit : 1 bit
■ Communication code : ASCII code
■ Use a crossed (reverse) cable.
■
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
! NOTE
G
No Connection
1
5
6
9
This product has command echo back in the
RS-232C Command.
RS-232C Configurations
Either cable below can be used.
7-Wire Configuration
(Serial female-female NULL modem cable)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
3-Wire Configurations
(Not standard)
PC
TV
2
3
5
4
6
7
8
3
2
5
6
4
7
8
D-Sub 9
D-Sub 9
RXD
TXD
GND
DTR
DSR
RTS
CTS
TXD
RXD
GND
DTR
DSR
RTS
CTS
Set ID
Use this function to specify a TV ID number.
Refer to ‘Real Data Mapping’.
OPTION
Move
Enter
: English
Menu Language
: English
: English
Audio Language
: English
Input Label
: On
SIMPLINK
: On
Key Lock
: Off
Key Lock
: Off
Simple Manual
Caption
: Off
Caption
: Off
Set ID
:1
Set ID
:1
ENTER
1
F
E
G
Close
APPENDIX
SIMPLINK
E
2
Enter
Audio Language
Simple Manual
MENU
Move
Menu Language
Input Label
1
OPTION
Select O P T I O N.
■
Real data mapping
0 : Step 0
Select Set ID.
A : Step 10 (SET ID 10)
3
ENTER
4
RETURN
MENU
Choose the desired TV ID number.
The adjustment range of Set ID is
1~99.
Return to the previous menu.
F : Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
63 : Step 99 (SET ID 99)
64 : Step 100
Return to TV viewing.
117
APPENDIX
Command Reference List
COMMAND1 COMMAND2
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD Select
13. Remote Control
Lock Mode
k
x
k
k
k
k
k
k
k
k
k
k
a
b
c
d
e
f
g
h
i
j
k
l
00 ~ 01
(G p.119)
(G p.119)
(G p.119)
00 ~ 01
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 01
k
m
00 ~ 01
COMMAND1 COMMAND2
20. Channel Tuning
DATA
(Hexadecimal)
m
a
COMMAND1 COMMAND2
14. Treble
15. Bass
16. Balance
17. Color Temperature
18. Energy Saving
19. Auto Configuration
21. Channel Add/Del
22. Key
23. Backlight
k
k
k
k
j
j
m
m
m
DATA
(Hexadecimal)
r
s
t
u
q
u
b
c
g
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 02
(G p.120)
(G p.120)
00 ~ 01
(G p.121)
00 ~ 64
DATA00
DATA01
DATA02
DATA03
DATA04
DATA05
(Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal)
physical
major
major low
program high program low
minor high
minor low
attribute
Transmission / Receiving Protocol
APPENDIX
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1] : First command to control the set.(j, k, m or x)
[Command 2] : Second command to control the set.
[Set ID] : You can adjust the set ID to choose desired TV ID
number in Setup menu. Adjustment range is 1~ 99.
When selecting Set ID ‘0’, every connected the TV is
controlled. Set ID is indicated as decimal (1~ 99) on
menu and as Hexa decimal (0x0~ 0x63) on transmission
/receiving protocol.
[DATA] : To transmit the command data.
Transmit the ‘FF’ data to read status of command.
[Cr] : Carriage Return
ASCII code ‘0x0D’
[ ] : ASCII code ‘space (0x20)’
* In this model, TV will not send the status during the standby mode.
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
The TV transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is
data read mode, it indicates present status data. If the data is
data write mode, it returns the data of the PC computer.
118
* In this model, TV will not send the status during the standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.
[OK] : Use the large character.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
The TV transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions
or communication errors.
Data1: Illegal Code
Data2: Not supported function
Data3: Wait more time
* In this model, TV will not send the status during the standby mode.
* Data Format
[Command 2] : Use as command.
[Set ID] : Use the small character, if set ID is 10, it will send the ‘0’, ‘a’.
[DATA] : Use the small character, if data is 0 x ab, it will send the ‘a’, ‘b’.
[NG] : Use the large character
01. Power (Command: k a)
To control Power On/Off of the TV.
You can also adjust mute using the MUTE button on
remote control.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
Transmission [k][e][ ][Set ID][ ][Data][Cr]
Data 00: Power Off
Data 00: Volume mute on (Volume off)
Data 01: Power On
Acknowledgement [a][ ][Set ID][ ][OK/NG][Data][x]
Data 01: Volume mute off (Volume on)
* In a like manner, if other functions transmit ‘FF’ data
based on this format, Acknowledgement data feedback
presents status about each function.
Acknowledgement [e][ ][Set ID][ ][OK/NG][Data][x]
* Note: In this model, TV will send the Acknowledge
after power on processing completion.
There might be a time delay between command and
acknowledge.
06. Volume Control (Command: k f)
To adjust volume.
You can also adjust volume with the volume buttons on
remote control.
Transmission [k][f][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
02. Input Select (Command: x b)
To select input source for TV.
*Refer to ‘Real data mapping’.
Acknowledgement [f][ ][Set ID][ ][OK/NG][Data][x]
Transmission [x][b][ ][Set ID][ ][Data][Cr]
Data 00: DTV (Antenna)
Data 01: DTV (Cable)
07. Contrast (Command: k g)
Data 10: Analog (Antenna) Data 11: Analog (Cable)
To adjust screen contrast.
Data 20: AV/AV1
You can also adjust contrast in the PICTURE menu.
Data 21: AV2
Data 40: Component/ Component1 Data 41: Component 2
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Data 60: RGB-PC
Data 90: HDMI/HDMI1
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Data 91: HDMI2
Data 92: HDMI3
*Refer to ‘Real data mapping’.
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
* Use the feature depending on your model.
08. Brightness (Command: k h)
03. Aspect Ratio (Command: k c)
To adjust the screen format.
To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data 01: 4:3
09: Just scan
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
10: Cinema Zoom1
*Refer to ‘Real data mapping’.
02: 16:9
04: Zoom
06: Set by program
Acknowledgement [h][ ][Set ID][ ][OK/NG][Data][x]
1F: Cinema Zoom16
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
APPENDIX
Transmission [k][c][ ][Set ID][ ][Data][Cr]
09. Color (Command: k i)
To adjust screen color.
04. Screen Mute (Command: k d)
You can also adjust color in the PICTURE menu.
To select screen mute on/off.
Transmission [k][i][ ][Set ID][ ][Data][Cr]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Data 00: Screen mute off (Picture on), Video-out Mute off
*Refer to ‘Real data mapping’.
Data 01: Screen mute on (Picture off)
Acknowledgement [i][ ][Set ID][ ][OK/NG][Data][x]
Data 10: Video-out Mute on
Acknowledgement [d][ ][Set ID][ ][OK/NG][Data][x]
* In case of Video-out Mute on only, TV will display On
Screen Display (OSD). But, in case of screen mute on,
TV will not display On Screen Display (OSD).
05. Volume Mute (Command: k e)
To control volume mute on/off.
10. Tint (Command: k j)
To adjust screen tint.
You can also adjust tint in the PICTURE menu.
Transmission [k][j][ ][Set ID][ ][Data][Cr]
Data Red: 00 ~ Green: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Acknowledgement [ j ][ ][Set ID][ ][OK/NG][Data][x]
119
APPENDIX
11. Sharpness (Command: k k)
*Refer to ‘Real data mapping’.
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
To adjust screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr]
17. Color Temperature (Command: k u)
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
To adjust color temperature.
*Refer to ‘Real data mapping’.
You can also adjust color temperature in the PICTURE menu.
Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][u][ ][Set ID][ ][Data][Cr]
Data 00: Medium 01: Cool 02: Warm
12. OSD Select (Command: k l)
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
To select OSD (On Screen Display) on/off.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00: OSD off
Data 01: OSD on
Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
18. Energy Saving (Command: j q)
To control the energy saving function.
Transmission [ j ][q][ ][Set ID][ ][Data][Cr]
Data 00: Energy saving - off
13. Remote Control Lock Mode (Command: k m)
To lock the remote control and the front panel controls
on the set.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00: Lock off
Data 01: Lock on
01: Energy saving - Minimum
02: Energy saving - Medium
03: Energy saving - Maximum
05: Energy saving - Screen off
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
If you’re not using the remote control and front panel
controls on the TV, use this mode. When main power is
on/off, remote control lock is released.
If Key Lock is on in the standby mode, TV will not turn on
by POWER button of remote control and on the TV.
19. Auto Configuration (Command: j u)
To adjust picture position and minimize image shaking
automatically. Auto configuration only works in RGB-PC
mode.
Transmission [ j ][u][ ][Set ID][ ][Data][Cr]
Data 01: To set
14. Treble (Command: k r)
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
To adjust treble.
APPENDIX
You can also adjust treble in the AUDIO menu.
To tune channel to following physical/major/minor number.
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]
*Refer to ‘Real data mapping’.
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]
Digital channels have a Physical, Major, and Minor channel
number. The Physical number is the actual digital channel
number, the Major is the number that the channel should
be mapped to, and the Minor is the sub-channel. Since
the ATSC tuner automatically maps the channel to the
Major number, the Physical number is not required when
sending a command.
15. Bass (Command: k s)
To adjust bass.
You can also adjust bass in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.
Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]
16. Balance (Command: k t)
To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
120
20. Channel Tuning (Command: m a)
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data 00: Physical Channel Number
NTSC air: 02~45, NTSC cable: 01, 0E~7D
ATSC air: 01~45, ATSC cable: 01~87
Data 01 & 02: Major Channel Number
Data 01: High byte
Data 02: Low byte
Two bytes are available for the Major and Minor, normally only the second byte is used.
Data 03 & 04: Minor Channel Number
Not needed for NTSC.
Data5:
7
Main/Sub
Picture
6
Two/One
Part Channel
5
Using Physical
Channel
4
3
2
1
0
Step
NTSC Air
NTSC Cable
ATSC Air
ATSC Cable_std
ATSC Cable_hrc
ATSC Cable_irc
ATSC cable_auto
Reserved
...
Reserved
Reserved
0 Main
0 Two
0 Use
x
0
0
0
0
1 Sub
1 One
1 No Use
x
0
0
0
1
x
0
0
1
0
x
0
0
1
1
x
0
1
0
0
x
0
1
0
1
x
0
1
1
0
x
0
1
1
1
x
x
x
x
x
x
1
1
1
1
The table above lists the binary code which must be
converted to Hexadecimal before sending. For example:
The binary code to tune the sub source to an NTSC
cable channel is “1000 0001”, which translates to “81”
in Hex.
* 7th bit : For which source do you want to change the
channel.
* 6th bit: Use a two part or one part channel. Most cases
just use 0 since it’s ignored when using NTSC.
21. Channel Add/Del (Command: m b)
To add and delete the channels.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00: Channel Delete
Data 01: Channel Add
Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x]
22. Key (Command: m c)
To send IR remote control code.
* 5th bit: Use 0 with NTSC since it can only use the physical channel number. Normally use 1 for ATSC since most
times it doesn’t matter what the physical number is.
Transmission [m][c][ ][Set ID][ ][Data][Cr]
* 4th bit: Set to 0.
Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x]
* 3-0 bits: Choose signal type.
When TV is in the standby mode, TV will turn on by
POWER button of remote control only.
See page 115.
* Tune Command Examples:
Data 00 = Physical of 35 = 23
23. Backlight (Command: m g)
To adjust screen backlight.
Data 01 & 02 = No Major = 00 00
Transmission [m][g][ ][Set ID][ ][Data][Cr]
Data 03 & 04 = No Minor = 00 00
Data Min:00 ~ Max:64 (*transmit by Hexadecimal code)
Data 05 = 0000 0001 in binary = 01
*Refer to ‘Real data mapping’.
Total = ma 00 23 00 00 00 00 01
Acknowledgement [g][ ][Set ID][ ][OK/NG][Data][x]
APPENDIX
1. Tune to the analog (NTSC) cable channel 35.
2. Tune to the digital (ATSC) local channel 30-3.
Data 00 = Don’t know Physical = 00
Data 01 & 02 = Major is 30 = 00 1E
Data 03 & 04 = Minor is 3 = 00 03
Data 05 = 0010 0010 in binary = 22
Total = ma 00 00 00 1E 00 03 22
Acknowledgement[a][ ][Set ID][ ][OK][Data00][Data01]
[Data02][Data03][Data04][x][a][ ][Set ID]
[ ][NG][Data00][x]
121
APPENDIX
OPEN SOURCE LICENSE - This feature is not available for all models.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51
Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of
this license document, but changing it is not allowed.
the program proprietary. To prevent this, we have made it clear
that any patent must be licensed for everyone's free use or not
licensed at all.
The precise terms and conditions for copying, distribution and
modification follow.
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General
Public License is intended to guarantee your freedom to share
and change free software - to make sure the software is free for
all its users. This General Public License applies to most of the
Free Software Foundation's software and to any other program
whose authors commit to using it. (Some other free software
foundation software is covered by the GNU Lesser General Public
License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not
price. Our General Public Licenses are designed to make sure that
you have the freedom to distribute copies of free software (and
charge for this service if you wish), that you receive source code
or can get it if you want it, that you can change the software or
use pieces of it in new free programs; and that you know you can
do these things.
APPENDIX
To protect your rights, we need to make restrictions that forbid
anyone to deny you these rights or to ask you to surrender the
rights. These restrictions translate to certain responsibilities for
you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether
gratis or for a fee, you must give the recipients all the rights that
you have. You must make sure that they, too, receive or can get
the source code. And you must show them these terms so they
know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
122
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION
0. This license applies to any program or other work which contains a notice placed by the copyright holder saying it may be
distributed under the terms of this General Public License. The
"Program", below, refers to any such program or work, and a
"work based on the Program" means either the Program or any
derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with
modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the
term "modification".) Each licensee is addressed as "you".
Activities other than copying, distribution and modification
are not covered by this license; they are outside its scope.
The act of running the Program is not restricted, and the output from the program is covered only if its contents constitute
a work based on the program (independent of having been
made by running the program). Whether that is true depends
on what the program does.
1. You may copy and distribute verbatim copies of the program's
source code as you receive it, in any medium, provided that
you conspicuously and appropriately publish on each copy an
appropriate copyright notice and disclaimer of warranty; keep
intact all the notices that refer to this license and to the
absence of any warranty; and give any other recipients of the
program a copy of this license along with the Program.
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.
Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this
free software. If the software is modified by someone else and
passed on, we want its recipients to know that what they have is
not the original, so that any problems introduced by others will
not reflect on the original authors' reputations.
2. You may modify your copy or copies of the program or any
portion of it, thus forming a work based on the Program, and
copy and distribute such modifications or work under the
terms of section 1 above, provided that you also meet all of
these conditions:
Finally, any free program is threatened constantly by software
patents. We wish to avoid the danger that redistributors of a free
program will individually obtain patent licenses, in effect making
a) You must cause the modified files to carry prominent
notices stating that you changed the files and the date of
any change.
b) You must cause any work that you distribute or publish,
that in whole or in part contains or is derived from the
Program or any part there of, to be licensed as a whole at
no charge to all third parties under the terms of this
license.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running
for such interactive use in the most ordinary way, to print
or display an announcement including an appropriate
copyright notice and a notice that there is no warranty (or
else, saying that you provide a warranty) and that users
may redistribute the program under these conditions, and
telling the user how to view a copy of this license.
(Exception: if the Program itself is interactive but does not
normally print such an announcement, your work based on
the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent and
separate works in themselves, then this license, and its terms,
do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections as
part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this license,
whose permissions for other licensees extend to the entire
whole, and thus to each and every part regardless of who
wrote it.
In addition, mere aggregation of another work not based on
the program with the Program (or with a work based on the
program) on a volume of a storage or distribution medium
does not bring the other work under the scope of this license.
3. You may copy and distribute the program (or a work based on
it, under section 2) in object code or executable form under
the terms of sections 1 and 2 above provided that you also
do one of the following:
a) Accompany it with the complete corresponding machinereadable source code, which must be distributed under the
terms of sections 1 and 2 above on a medium customarily
used for software interchange; or,
b) Accompany it with a written offer, valid for at least three
years, to give any third party, for a charge no more than
your cost of physically performing source distribution, a
complete machine-readable copy of the corresponding
source code, to be distributed under the terms of sections
1 and 2 above on a medium customarily used for software
interchange; or,
The source code for a work means the preferred form of the
work for making modifications to it. For an executable work,
complete source code means all the source code for all modules it contains, plus any associated interface definition files,
plus the scripts used to control compilation and installation
of the executable. However, as a special exception, the source
code distributed need not include anything that is normally
distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating
system on which the executable runs, unless that component
itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same
place counts as distribution of the source code, even though
third parties are not compelled to copy the source along with
the object code.
4. You may not copy, modify, sublicense, or distribute the Program
except as expressly provided under this license. Any attempt
otherwise to copy, modify, sublicense or distribute the
Program is void, and will automatically terminate your rights
under this license. However, parties who have received copies,
or rights, from you under this license will not have their licenses terminated so long as such parties remain in full compliance.
APPENDIX
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of
derivative or collective works based on the program.
c) Accompany it with the information you received as to the
offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and
only if you received the program in object code or executable form with such an offer, in accord with Subsection
b above.)
5. You are not required to accept this license, since you have not
signed it. However, nothing else grants you permission to
modify or distribute the Program or its derivative works.
These actions are prohibited by law if you do not accept this
license. Therefore, by modifying or distributing the program
(or any work based on the program), you indicate your acceptance of this license to do so, and all its terms and conditions
for copying, distributing or modifying the program or works
based on it.
6. Each time you redistribute the program (or any work based on
the Program), the recipient automatically receives a license
from the original licensor to copy, distribute or modify the
Program subject to these terms and conditions. You may not
impose any further restrictions on the recipients' exercise of
the rights granted herein. You are not responsible for enforcing compliance by third parties to this license.
123
APPENDIX
7. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by
court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license. If you cannot distribute so as to satisfy simultaneously your obligations under this license and any
other pertinent obligations, then as a consequence you may
not distribute the program at all. For example, if a patent
license would not permit royalty-free redistribution of the
program by all those who receive copies directly or indirectly
through you, then the only way you could satisfy both it and
this license would be to refrain entirely from distribution of
the program.
any later version published by the Free Software Foundation.
If the program does not specify a version number of this
license, you may choose any version ever published by the
Free Software Foundation.
10.If you wish to incorporate parts of the program into other free
programs whose distribution conditions are different, write to
the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free
Software Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of preserving the
free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply and the section as a whole is intended to
apply in other circumstances.
APPENDIX
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of
protecting the integrity of the free software distribution system, which is implemented by public license practices. Many
people have made generous contributions to the wide range
of software distributed through that system in reliance on
consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute
software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this license.
8. If the distribution and/or use of the program is restricted in
certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the program
under this license may add an explicit geographical distribution
limitation excluding those countries, so that distribution is
permitted only in or among countries not thus excluded. In
such case, this license incorporates the limitation as if written
in the body of this license.
9. The Free Software Foundation may publish revised and/or
new versions of the General Public License from time to time.
Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the
program specifies a version number of this license which
applies to it and "any later version", you have the option of
following the terms and conditions either of that version or of
124
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS
IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE
RISK AS TO THE QUALITY AND PERFORMANCE OF THE
PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA
OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to apply these terms to your new programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to
make it free software which everyone can redistribute and change
under these terms.
To do so, attach the following notices to the program. It is safest
to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at
least the "copyright" line and a pointer to where the full notice is
found.
one line to give the program's name and a brief idea of what it
does.
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or
modify it under the terms of the GNU General Public License as
published by the Free Software Foundation; either version 2 of
the license, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty
of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details.
If the program is interactive, make it output a short notice like
this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for
details type ‘show w’. This is free software, and you are welcome
to redistribute it under certain conditions; type ‘show c’ for
details.
The hypothetical commands ‘show w’ and ‘show c’ should show
the appropriate parts of the General Public License. Of course,
the commands you use may be called something other than
‘show w’ and ‘show c’; they could even be mouse-clicks or menu
items-whatever suits your program.
You should also get your employer (if you work as a programmer)
or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by
James Hacker.
signature of Ty Coon, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your
program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to
do, use the GNU Lesser General Public License instead of this
license.
APPENDIX
You should have received a copy of the GNU General Public
License along with this program; if not, write to the Free Software
Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301 USA.
Also add information on how to contact you by electronic and
paper mail.
125
APPENDIX
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51
Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of
this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also
counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General
Public Licenses are intended to guarantee your freedom to share
and change free software - to make sure the software is free for
all its users.
This license, the Lesser General Public License, applies to some
specially designated software packages - typically libraries - of
the Free Software Foundation and other authors who decide to
use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public
License is the better strategy to use in any particular case, based
on the explanations below.
APPENDIX
When we speak of free software, we are referring to freedom of
use, not price. Our General Public Licenses are designed to make
sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive
source code or can get it if you want it; that you can change the
software and use pieces of it in new free programs; and that you
are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid
distributors to deny you these rights or to ask you to surrender
these rights. These restrictions translate to certain responsibilities
for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis
or for a fee, you must give the recipients all the rights that we
gave you. You must make sure that they, too, receive or can get
the source code. If you link other code with the library, you must
provide complete object files to the recipients, so that they can
relink them with the library after making changes to the library
and recompiling it. And you must show them these terms so they
know their rights.
We protect your rights with a two-step method: (1) we copyright
the library, and (2) we offer you this license, which gives you legal
permission to copy, distribute and/or modify the library.
126
To protect each distributor, we want to make it very clear that
there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know
that what they have is not the original version, so that the original author's reputation will not be affected by problems that
might be introduced by others.
Finally, software patents pose a constant threat to the existence
of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a
restrictive license from a patent holder. Therefore, we insist that
any patent license obtained for a version of the library must be
consistent with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the
ordinary GNU General Public License. This license, the GNU
Lesser General Public License, applies to certain designated
libraries, and is quite different from the ordinary General Public
License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.
When a program is linked with a library, whether statically or
using a shared library, the combination of the two is legally
speaking a combined work, a derivative of the original library. The
ordinary General Public License therefore permits such linking
only if the entire combination fits its criteria of freedom. The
Lesser General Public License permits more lax criteria for linking
other code with the library.
We call this license the "Lesser" General Public License because
it does Less to protect the user's freedom than the ordinary
General Public License. It also provides other free software developers Less of an advantage over competing non-free programs.
These disadvantages are the reason we use the ordinary General
Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to
encourage the widest possible use of a certain library, so that it
becomes a de-facto standard. To achieve this, non-free programs
must be allowed to use the library. A more frequent case is that
a free library does the same job as widely used non-free libraries.
In this case, there is little to gain by limiting the free library to free
software only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in non-free
programs enables a greater number of people to use a large body
of free software. For example, permission to use the GNU C
Library in non-free programs enables many more people to use
the whole GNU operating system, as well as its variant, the
GNU/Linux operating system.
Although the Lesser General Public License is Less protective of
the users' freedom, it does ensure that the user of a program that
is linked with the Library has the freedom and the wherewithal to
run that program using a modified version of the Library.
each copy an appropriate copyright notice and disclaimer of
warranty; keep intact all the notices that refer to this license
and to the absence of any warranty; and distribute a copy of
this license along with the Library.
The precise terms and conditions for copying, distribution and
modification follow. Pay close attention to the difference between
a "work based on the library" and a "work that uses the library".
The former contains code derived from the library, whereas the
latter must be combined with the library in order to run.
You may charge a fee for the physical act of transferring a
copy, and you may at your option offer warranty protection in
exchange for a fee.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION
0. This license agreement applies to any software library or other
program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed
under the terms of this Lesser General Public License (also
called “this license”). Each license is addressed as "you".
A “library” means a collection of software functions and/or
data prepared so as to be conveniently linked with application
programs (which use some of those functions and data) to
form executables.
“Source code” for a work means the preferred form of the
work for making modifications to it. For a library, complete
source code means all the source code for all modules it contains, plus any associated interface definition files, plus the
scripts used to control compilation and installation of the
library.
Activities other than copying, distribution and modification
are not covered by this license; they are outside its scope.
The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the library (independent of
the use of the Library in a tool for writing it). Whether that is
true depends on what the library does and what the program
that uses the library does.
1. You may copy and distribute verbatim copies of the library's
complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on
(For example, a function in a library to compute square roots
has a purpose that is entirely well-defined independent of the
application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be
optional: if the application does not supply it, the square root
function must still compute square roots.)
APPENDIX
The “Library”, below, refers to any such software library or work
which has been distributed under these terms. A “work based
on the Library” means either the Library or any derivative work
under copyright law: that is to say, a work containing the
library or a portion of it, either verbatim or with modifications
and/or translated straightforwardly into another language.
(Hereinafter, translation is included without limitation in the
term “modification”.)
2. You may modify your copy or copies of the Library or any
portion of it, thus forming a work based on the Library, and
copy and distribute such modifications or work under the
terms of section 1 above, provided that you also meet all of
these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent
notices stating that you changed the files and the date of
any change.
c) You must cause the whole of the work to be licensed at no
charge to all third parties under the terms of this license.
d) If a facility in the modified Library refers to a function or a
table of data to be supplied by an application program that
uses the facility, other than as an argument passed when
the facility is invoked, then you must make a good faith
effort to ensure that, in the event an application does not
supply such function or table, the facility still operates, and
performs whatever part of its purpose remains meaningful.
These requirements apply to the modified work as a whole. If
identifiable sections of that work are not derived from the
library, and can be reasonably considered independent and
separate works in themselves, then this license, and its terms,
do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections as
part of a whole which is a work based on the library, the distribution of the whole must be on the terms of this license,
whose permissions for other licenses extend to the entire
whole, and thus to each and every part regardless of who
wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the
intent is to exercise the right to control the distribution of
derivative or collective works based on the library.
In addition, mere aggregation of another work not based on
the library with the library (or with a work based on the
library) on a volume of a storage or distribution medium does
not bring the other work under the scope of this license.
127
APPENDIX
3. You may opt to apply the terms of the ordinary GNU General
Public License instead of this License to a given copy of the
Library. To do this, you must alter all the notices that refer to
this License, so that they refer to the ordinary GNU General
Public License, version 2, instead of to this License. (If a newer
version than version 2 of the ordinary GNU General Public
License has appeared, then you can specify that version
instead if you wish.) Do not make any other change in these
notices.
Once this change is made in a given copy, it is irreversible for
that copy, so the ordinary GNU General Public License applies
to all subsequent copies and derivative works made from that
copy.
This option is useful when you wish to copy part of the code
of the library into a program that is not a library.
4. You may copy and distribute the library (or a portion or derivative of it, under Section 2) in object code or executable form
under the terms of Sections 1 and 2 above provided that you
accompany it with the complete corresponding machinereadable source code, which must be distributed under the
terms of sections 1 and 2 above on a medium customarily
used for software interchange.
If distribution of object code is made by offering access to
copy from a designated place, then offering equivalent access
to copy the source code from the same place satisfies the
requirement to distribute the source code, even though third
parties are not compelled to copy the source along with the
object code.
APPENDIX
5. A program that contains no derivative of any portion of the
Library, but is designed to work with the Library by being
compiled or linked with it, is called a “work that uses the
Library”. Such a work, in isolation, is not a derivative work of
the Library, and therefore falls outside the scope of this
license.
However, linking a “work that uses the library” with the Library
creates an executable that is a derivative of the Library
(because it contains portions of the library), rather than a
“work that uses the library”. The executable is therefore covered by this license. Section 6 states terms for distribution of
such executable.
When a “work that uses the library” uses material from a header file that is part of the library, the object code for the work
may be a derivative work of the library even though the source
code is not.
Whether this is true is especially significant if the work can be
linked without the library, or if the work is itself a library. The
threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data
structure layouts and accessories, and small macros and small
inline functions (ten lines or less in length), then the use of
128
the object file is unrestricted, regardless of whether it is legally a derivative work. (Executable containing this object code
plus portions of the library will still fall under Section 6.)
Otherwise, if the work is a derivative of the library, you may
distribute the object code for the work under the terms of
Section 6. Any executable containing that work also fall under
Section 6, whether or not they are linked directly with the
library itself.
6. As an exception to the sections above, you may also combine
or link a "work that uses the library" with the library to produce a work containing portions of the library, and distribute
that work under terms of your choice, provided that the terms
permit modification of the work for the customer's own use
and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work
that the library is used in it and that the Library and its use
are covered by this license. You must supply a copy of this
license. If the work during execution displays copyright
notices, you must include the copyright notice for the library
among them, as well as a reference directing the user to the
copy of this license. Also, you must do one of these things:
a) Accompany the work with the complete corresponding
machine-readable source code for the library including
whatever changes were used in the work (which must be
distributed under Sections 1 and 2 above); and, if the work
is an executable linked with the Library, with the complete
machine-readable “work that uses the Library”, as object
code and/or source code, so that the user can modify the
library and then relink to produce a modified executable
containing the modified library. (It is understood that the
user who changes the contents of definitions files in the
library will not necessarily be able to recompile the application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the
library. A suitable mechanism is one that (1) uses at run time
a copy of the library already present on the user’s computer
system, rather than copying library functions into the executable, and (2) will operate properly with a modified version
of the library, if the user installs one, as long as the modified
version is interface-compatible with the version that the
work was made with.
c) Accompany the work with a written offer, valid for at least
three years, to give the same user the materials specified in
Subsection 6, above, for a charge no more than the cost of
performing this distribution.
d) If distribution of the work is made by offering access to
copy from a designated place, offer equivalent access to
copy the above specified materials from the same place.
e) Verify that the user has already received a copy of these
materials or that you have already sent this user a copy.
For an executable, the required form of the "work that uses
the library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not
include anything that is normally distributed (in either source
or binary form) with the major components (compiler, kernel,
and so on) of the operating system on which the executable
runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license
restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction
means you cannot use both them and the library together in
an executable that you distribute.
7. You may place library facilities that are a work based on the
library side-by-side in a single library together with other
library facilities not covered by this license, and distribute
such a combined library, provided that the separate distribution of the work based on the Library and of the other library
facilities is otherwise permitted, and provided that you do
these two things:
8. You may not copy, modify, sublicense, link with, or distribute
the library except as expressly provided under this license.
Any attempt otherwise to copy, modify, sublicense, link with,
or distribute the library is void, and will automatically terminate your rights under this license. However, parties who have
received copies, or rights, from you under this license will not
have their licenses terminated so long as such parties remain
in full compliance.
9. You are not required to accept this license, since you have not
signed it. However, nothing else grants you permission to modify or distribute the library or its derivative works. These
actions are prohibited by law if you do not accept this license.
Therefore, by modifying or distributing the library (or any work
based on the library), you indicate your acceptance of this
license to do so, and all its terms and conditions for copying,
distributing or modifying the library or works based on it.
10.Each time you redistribute the library (or any work based on
the Library), the recipient automatically receives a license
from the original licensor to copy, distribute, link with or modify the library subject to these terms and conditions. You may
not impose any further restrictions on the recipients' exercise
11. If, as a consequence of a court judgment or allegation of
patent infringement or for any other reason (not limited to
patent issues), conditions are imposed on you (whether by
court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license. If you cannot distribute so as to satisfy simultaneously your obligations under this license and any
other pertinent obligations, then as a consequence you may
not distribute the library at all. For example, if a patent license
would not permit royalty-free redistribution of the library by
all those who receive copies directly or indirectly through
you, then the only way you could satisfy both it and this
license would be to refrain entirely from distribution of the
library.
If any portion of this section is held invalid or unenforceable
under any particular circumstance, the balance of the section
is intended to apply, and the section as a whole is intended to
apply in other circumstances.
It is not the purpose of this section to induce you to infringe
any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of
protecting the integrity of the free software distribution system which is implemented by public license practices. Many
people have made generous contributions to the wide range
of software distributed through that system in reliance on
consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute
software through any other system and a license cannot
impose that choice.
This section is intended to make thoroughly clear what is
believed to be a consequence of the rest of this license.
APPENDIX
a) Accompany the combined library with a copy of the same
work based on the Library, uncombined with any other
library facilities. This must be distributed under the terms
of the sections above.
b) Give prominent notice with the combined library of the
fact that part of it is a work based on the library, and
explaining where to find the accompanying uncombined
form of the same work.
of the rights granted herein.
You are not responsible for enforcing compliance by third
parties with this license.
12.If the distribution and/or use of the library is restricted in certain countries either by patents or by copyrighted interfaces,
the original copyright holder who places the library under this
license may add an explicit geographical distribution limitation
excluding those countries, so that distribution is permitted
only in or among countries not thus excluded. In such case,
this license incorporates the limitation as if written in the body
of this license.
13.The Free Software Foundation may publish revised and/or
new versions of the Lesser General Public License from time to
time. Such new versions will be similar in spirit to the present
version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the
library specifies a version number of this license which applies
to it and “any later version”, you have the option of following
the terms and conditions either of that version or of any later
version published by the Free Software Foundation.
129
APPENDIX
If the library does not specify a license version number, you
may choose any version ever published by the Free Software
Foundation.
14.If you wish to incorporate parts of the library into other free
programs whose distribution conditions are incompatible with
these, write to the author to ask for permission. For software
which is copyrighted by the Free Software Foundation, write
to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free software
and of promoting the sharing and reuse of software generally.
To apply these terms, attach the following notices to the library.
It is safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty; and each file should
have at least the “copyright” line and a pointer to where the full
notice is found.
one line to give the library's name and a brief idea of what it does.
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify
it under the terms of the GNU Lesser General Public License as
published by the Free Software Foundation; either version 2.1 of
the license, or (at your option) any later version.
NO WARRANTY
15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE LIBRARY, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS
IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE
RISK AS TO THE QUALITY AND PERFORMANCE OF THE
LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
APPENDIX
16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA
OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE),
EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to apply these terms to your new libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so
by permitting redistribution under these terms (or, alternatively,
under the terms of the ordinary General Public License).
130
This library is distributed in the hope that it will be useful, but
WITHOUT ANY WARRANTY; without even the implied warranty
of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more
details.
You should have received a copy of the GNU Lesser General
Public License along with this library; if not, write to the Free
Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
MA 02110-1301 USA
Also add information on how to contact you by electronic and
paper mail.
You should also get your employer (if you work as a programmer)
or your school, if any, to sign a “copyright disclaimer” for the
library, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the
library ‘Frob’ (a library for tweaking knobs) written by James
Random Hacker.
signature of Ty Coon, 1 April 1990
Ty Coon, President of Vice
MOZILLA PUBLIC LICENSE
Version 1.1
--------------code which is described in the source code notice
required by exhibit as original code, and which, at the time
of its release under this license is not already covered
code governed by this license.
1.Definitions.
1.0.1. “Commercial use” means distribution or otherwise making
the covered code available to a third party.
1.1.
“Contributor” means each entity that creates or contributes to the creation of modifications.
1.2.
“Contributor version” means the combination of the original code, prior modifications used by a contributor, and
the modifications made by that particular contributor.
1.3.
“Covered code” means the original code or modifications
or the combination of the original code and modifications,
in each case including portions thereof.
1.4.
“Electronic distribution mechanism” means a mechanism
generally accepted in the software development community for the electronic transfer of data.
1.5.
“Executable” means covered code in any form other than
source code.
“Initial developer” means the individual or entity identified
as the initial Developer in the Source Code notice required
by exhibit A.
1.7.
“Larger work” means a work which combines covered code
or portions thereof with code not governed by the terms
of this License.
1.8.
“License” means this document.
1.8.1. “Licensable” means having the right to grant, to the maximum extent possible, whether at the time of the initial
grant or subsequently acquired, any and all of the rights
conveyed herein.
1.9.
“Modifications” means any addition to or deletion from
the substance or structure of either the original code or
any previous modifications. When covered code is
released as a series of files, a modification is:
A. Any addition to or deletion from the contents of a file
containing original code or previous modifications.
B. Any new file that contains any part of the original code
or previous modifications.
1.11. “Source code” means the preferred form of the covered
code for making modifications to it, including all modules
it contains, plus any associated interface definition files,
scripts used to control compilation and installation of an
executable, or source code differential comparisons
against either the original code or another well known,
available covered code of the contributor's choice. The
source code can be in a compressed or archival form, provided the appropriate decompression or de-archiving software is widely available for no charge.
1.12. “You” (or “Your”) means an individual or a legal entity
exercising rights under, and complying with all of the terms
of, this license or a future version of this license issued
under section 6.1.
For legal entities, “You” includes any entity which controls,
is controlled by, or is under common control with You. For
purposes of this definition, “control” means (a) the power,
direct or indirect, to cause the direction or management of
such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity.
APPENDIX
1.6.
1.10.1.“Patent claims” means any patent claim(s), now owned or
hereafter acquired, including without limitation, method,
process, and apparatus claims, in any patent licensable by
grantor.
2. Source Code License.
2.1.
The initial developer grant.
The initial developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property claims:
a) under intellectual property rights (other than patent or
trademark) licensable by initial developer to use, reproduce, modify, display, perform, sublicense and distribute the original code (or portions thereof) with or without modifications, and/or as part of a larger work; and
(b) under patents claims infringed by the making, using or
selling of original code, to make, have made, use, practice, sell, and offer for sale, and/or otherwise dispose
of the original code (or portions there of).
1.10. “Original code” means source code of computer software
131
APPENDIX
(c) the licenses granted in this section 2.1(a) and (b) are
effective on the date Initial developer first distributes
original code under the terms of this license.
(d) Notwithstanding section 2.1(b) above, no patent
license is granted: 1) for code that You delete from the
original Code; 2) separate from the original code; or
3) for infringements caused by: i) the modification of
the original code or ii) the combination of the original
code with other software or devices.
2.2.
APPENDIX
3. Distribution Obligations.
132
3.2.
Availability of source code.
Any modification which you create or to which you contribute must be made available in source code form under
the terms of this license either on the same media as an
executable version or via an accepted electronic distribution mechanism to anyone to whom you made an executable version available; and if made available via electronic distribution mechanism, must remain available for at
least twelve (12) months after the date it initially became
available, or at least six (6) months after a subsequent
version of that particular modification has been made
available to such recipients. You are responsible for ensuring that the source code version remains available even if
the electronic distribution mechanism is maintained by a
third party.
3.3.
Description of modifications.
You must cause all covered code to which you contribute to
contain a file documenting the changes You made to create
that covered code and the date of any change. You must
include a prominent statement that the modification is
derived, directly or indirectly, from original code provided by
the initial developer and including the name of the initial
developer in (a) the source code, and (b) in any notice in an
executable version or related documentation in which you
describe the origin or ownership of the covered code.
3.4.
Intellectual property matters
(a) Third party claims.
If contributor has knowledge that a license under a third
party's intellectual property rights is required to exercise
the rights granted by such contributor under sections 2.1
or 2.2, contributor must include a text file with the source
code distribution titled "LEGAL" which describes the claim
and the party making the claim in sufficient detail that a
recipient will know whom to contact. If contributor obtains
such knowledge after the modification is made available as
described in section 3.2, contributor shall promptly modify the LEGAL file in all copies contributor makes available
thereafter and shall take other steps (such as notifying
appropriate mailing lists or newsgroups) reasonably calculated to inform those who received the covered code that
new knowledge has been obtained.
(b) Contributor APIs.
If contributor's modifications include an application
programming interface and contributor has knowledge of
patent licenses which are reasonably necessary to implement
that API, contributor must also include this information in
the LEGAL file.
Contributor Grant.
Subject to third party intellectual property claims, each
contributor hereby grants You a world-wide, royalty-free,
non-exclusive license
(a) under intellectual property rights (other than patent
or trademark) licensable by contributor, to use,
reproduce, modify, display, perform, sublicense and
distribute the modifications created by such contributor (or portions thereof) either on an unmodified
basis, with other modifications, as covered code
and/or as part of a larger work; and
(b) under patent claims infringed by the making, using, or
selling of modifications made by that contributor
either alone and/or in combination with its contributor
version (or portions of such combination), to make,
use, sell, offer for sale, have made, and/or otherwise
dispose of: 1) modifications made by that contributor
(or portions thereof); and 2) the combination of modifications made by that contributor with its contributor
version (or portions of such combination).
(c) the licenses granted in sections 2.2(a) and 2.2(b) are
effective on the date contributor first makes commercial use of the covered code.
(d) Notwithstanding section 2.2(b) above, no patent
license is granted: 1) for any code that contributor has
deleted from the contributor version; 2) separate from
the contributor version; 3) for infringements caused
by: i) third party modifications of contributor version
or ii) the combination of modifications made by that
contributor with other software (except as part of the
contributor version) or other devices; or 4) under
patent claims infringed by covered code in the
absence of modifications made by that contributor.
3.1.
You may not offer or impose any terms on any source code
version that alters or restricts the applicable version of
this license or the recipients' rights hereunder. However,
you may include an additional document offering the
additional rights described in section 3.5.
Application of license.
The modifications which You create or to which you contribute are governed by the terms of this license, including
without limitation section 2.2. The source code version of
covered code may be distributed only under the terms of
this license or a future version of this license released
under section 6.1, and you must include a copy of this
license with every copy of the source code you distribute.
3.5.
3.7.
Required notices.
You must duplicate the notice in exhibit A in each file of
the source code. If it is not possible to put such notice in
a particular source code file due to its structure, then You
must include such notice in a location (such as a relevant
directory) where a user would be likely to look for such a
notice. If You created one or more modification(s), you
may add your name as a contributor to the notice
described in exhibit A. you must also duplicate this license
in any documentation for the source code where You
describe recipients' rights or ownership rights relating to
covered code. You may choose to offer, and to charge a
fee for, warranty, support, indemnity or liability obligations
to one or more recipients of covered code. However, you
may do so only on your own behalf, and not on behalf of
the Initial developer or any contributor. You must make it
absolutely clear than any such warranty, support, indemnity or liability obligation is offered by you alone, and You
hereby agree to indemnify the Initial developer and every
contributor for any liability incurred by the Initial developer or such contributor as a result of warranty, support,
indemnity or liability terms you offer.
4. Inability to comply due to statute or regulation.
If it is impossible for you to comply with any of the terms
of this license with respect to some or all of the covered
code due to statute, judicial order, or regulation then you
must: (a) comply with the terms of this license to the maximum extent possible; and (b) describe the limitations and
the code they affect. Such description must be included in
the LEGAL file described in section 3.4 and must be
included with all distributions of the source code. Except
to the extent prohibited by statute or regulation, such
description must be sufficiently detailed for a recipient of
ordinary skill to be able to understand it.
Distribution of executable versions.
You may distribute covered code in executable form only if
the requirements of section 3.1-3.5 have been met for
that covered code, and if you include a notice stating that
the source code version of the covered code is available
under the terms of this license, including a description of
how and where you have fulfilled the obligations of section
3.2. The notice must be conspicuously included in any
notice in an executable version, related documentation or
collateral in which you describe recipients' rights relating
to the covered code. You may distribute the executable
version of covered code or ownership rights under a
license of your choice, which may contain terms different
from this license, provided that you are in compliance with
the terms of this license and that the license for the executable version does not attempt to limit or alter the recipient's rights in the source code version from the rights set
forth in this license. If you distribute the executable version under a different license you must make it absolutely
clear that any terms which differ from this license are
offered by you alone, not by the Initial developer or any
contributor. You hereby agree to indemnify the initial
developer and every contributor for any liability incurred
by the initial developer or such contributor as a result of
any such terms You offer.
Larger works.
You may create a larger work by combining covered code
with other code not governed by the terms of this license
and distribute the larger work as a single product. In such
a case, you must make sure the requirements of this
license are fulfilled for the covered code.
5. Application of this license.
This license applies to code to which the initial developer has
attached the notice in exhibit A and to related covered code.
6. Versions of the license.
6.1.
New versions.
Netscape communications corporation (“Netscape”) may
publish revised and/or new versions of the license from
time to time. Each version will be given a distinguishing
version number.
6.2.
Effect of new versions.
Once covered code has been published under a particular
version of the license, you may always continue to use it
under the terms of that version. You may also choose to
use such covered code under the terms of any subsequent
version of the license published by netscape. No one
other than netscape has the right to modify the terms
applicable to covered code created under this license.
6.3.
Derivative works.
If You create or use a modified version of this license
(which you may only do in order to apply it to code which
is not already covered code governed by this license), You
must (a) rename Your license so that the phrases
"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL",
"NPL" or any confusingly similar phrase do not appear in
your license (except to note that your license differs from
this license) and (b) otherwise make it clear that Your
version of the license contains terms which differ from the
Mozilla Public license and netscape Public License. (Filling
in the name of the initial developer, original code or contributor in the notice described in exhibit A shall not of
themselves be deemed to be modifications of this license.)
APPENDIX
3.6.
(c) Representations.
contributor represents that, except as disclosed pursuant
to section 3.4(a) above, contributor believes that contributor's
modifications are contributor's original creation(s)
and/or contributor has sufficient rights to grant the rights
conveyed by this license.
133
APPENDIX
7. DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS LICENSE
ON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT
FOR A PARTICULAR PURPOSE OR NON-INFRINGING.
THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU.
SHOULD ANY COVERED CODE PROVE DEFECTIVE IN
ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR
ANY OTHER CONTRIBUTOR) ASSUME THE COST OF
ANY NECESSARY SERVICING, REPAIR OR CORRECTION.
THIS DISCLAIMER OF WARRANTY CONSTITUTES AN
ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY
COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT
UNDER THIS DISCLAIMER.
8. TERMINATION.
8.1.
8.2.
APPENDIX
134
This license and the rights granted hereunder will terminate
automatically if you fail to comply with terms herein and
fail to cure such breach within 30 days of becoming aware
of the breach. All sublicenses to the covered code which
are properly granted shall survive any termination of this
license. Provisions which, by their nature, must remain in
effect beyond the termination of this license shall survive.
If you initiate litigation by asserting a patent infringement
claim (excluding declatory judgment actions) against initial developer or a contributor (the initial developer or
contributor against whom you file such action is referred
to as “Participant”) alleging that:
(a) such participant's contributor version directly or indirectly infringes any patent, then any and all rights
granted by such participant to you under sections 2.1
and/or 2.2 of this license shall, upon 60 days notice
from Participant terminate prospectively, unless if within
60 days after receipt of notice you either: (i) agree in
writing to pay participant a mutually agreeable reasonable
royalty for your past and future use of modifications
made by such participant, or (ii) withdraw your litigation
claim with respect to the contributor version against
such participant. If within 60 days of notice, a reasonable
royalty and payment arrangement are not mutually
agreed upon in writing by the parties or the litigation
claim is not withdrawn, the rights granted by participant to you under sections 2.1 and/or 2.2 automatically terminate at the expiration of the 60 day notice
period specified above.
(b) any software, hardware, or device, other than such participant's contributor Version, directly or indirectly
infringes any patent, then any rights granted to You by
such participant under sections 2.1(b) and 2.2(b) are
revoked effective as of the date you first made, used,
sold, distributed, or had made, modifications made by
that participant.
8.3.
If you assert a patent infringement claim against participant alleging that such participant's contributor version
directly or indirectly infringes any patent where such claim
is resolved (such as by license or settlement) prior to the
initiation of patent infringement litigation, then the reasonable value of the licenses granted by such participant
under sections 2.1 or 2.2 shall be taken into account in
determining the amount or value of any payment or
license.
8.4.
In the event of termination under sections 8.1 or 8.2
above, all end user license agreements (excluding distributors
and resellers) which have been validly granted by you or
any distributor hereunder prior to termination shall survive
termination.
9. LIMITATION OF LIABILITY.
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL
THEORY, WHETHER TORT (INCLUDING NEGLIGENCE),
CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL
DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF
ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL,
WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE
BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY
TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT
APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT
APPLY TO YOU.
10. U.S. GOVERNMENT END USERS.
The covered code is a "commercial item," as that term is
defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of
"commercial computer software" and "commercial computer
software documentation," as such terms are used in 48
C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R.
12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4
(June 1995), all U.S. Government end users acquire covered code with only those rights set forth herein.
11. MISCELLANEOUS.
This license represents the complete agreement concerning
subject matter hereof. If any provision of this license is
held to be unenforceable, such provision shall be reformed
only to the extent necessary to make it enforceable. This
License shall be governed by California law provisions
(except to the extent applicable law, if any, provides otherwise), excluding its conflict-of-law provisions. With
respect to disputes in which at least one party is a citizen
of, or an entity chartered or registered to do business in
the united states of america, any litigation relating to this
License shall be subject to the jurisdiction of the federal
courts of the northern district of california, with venue
lying in santa clara county, california, with the losing party
responsible for costs, including without limitation, court
costs and reasonable attorneys' fees and expenses. The
application of the united nations convention on contracts
for the International sale of goods is expressly excluded.
Any law or regulation which provides that the language of
a contract shall be construed against the drafter shall not
apply to this license.
EXHIBIT A -Mozilla Public License.
12. RESPONSIBILITY FOR CLAIMS.
As between initial developer and the contributors, each
party is responsible for claims and damages arising, directly
or indirectly, out of its utilization of rights under this
license and you agree to work with initial developer and
contributors to distribute such responsibility on an equitable
basis. Nothing herein is intended or shall be deemed to
constitute any admission of liability.
Alternatively, the contents of this file may be used under the
terms of the _____ license (the "[___] License"), in which case
the provisions of [______] license are applicable instead of those
above. If you wish to allow use of your version of this file only
under the terms of the [____] license and not to allow others to
use your version of this file under the MPL, indicate your decision
by deleting the provisions above and replace them with the
notice and other provisions required by the [___] license. If you
do not delete the provisions above, a recipient may use your version
of this file under either the MPL or the [___] license."
Software distributed under the license is distributed on an "AS
IS" basis, WITHOUT WARRANTY OF ANY KIND, either express
or implied. See the license for the specific language governing
rights and limitations under the License.
The Original Code is ______________________________________.
The
Initial
Developer
of
the
Original
Code
is___________________.
Portions created by ______________________ are Copyright (C)
_______________________. All Rights Reserved.
Contributor(s): ______________________________________.
NOTE: The text of this exhibit A may differ slightly from the text
of the notices in the source code files of the original code. You
should use the text of this exhibit A rather than the text found in
the original code/source code for Your modifications.
APPENDIX
13. MULTIPLE-LICENSED CODE.
Initial developer may designate portions of the covered
code as "Multiple-Licensed". "Multiple-Licensed" means
that the initial developer permits you to utilize portions of
the covered code under your choice of the NPL or the
alternative licenses, if any, specified by the initial developer
in the file described in exhibit A.
The contents of this file are subject to the Mozilla Public License
Version 1.1 (the “license”); you may not use this file except in
compliance with the License. You may obtain a copy of the
license at http://www.mozilla.org/MPL/
135