Cisco WS-C2360-48TD-S network switch

Data Sheet
Cisco Catalyst 2360 Series Switches
Product Overview
®
The Cisco Catalyst 2360 Series Switches are high-speed Layer 2 top-of-rack switches that provide Gigabit Ethernet
server aggregation in the data center. The Cisco Catalyst 2360 Series is designed to meet the demands of today’s
data center, including high performance and high availability.
The Cisco Catalyst 2360 Series provides wire-rate performance, local switching, with a non-blocking, low-latency
architecture. The Cisco Catalyst 2360 Series comes with reversible front-to-back or back-to-front airflow, as well as
power and cooling redundancy. It provides these features with extremely low power consumption. Figure 1 shows a
Cisco Catalyst 2360 Series Switch.
Figure 1.
Cisco Catalyst 2360 Series Switch
The Cisco Catalyst 2360 Series switches offers the following features:
●
48 ports of Gigabit Ethernet 10/100/1000-Gbps downlink connectivity
●
Four 10 Gigabit Ethernet Small Form-Factor Pluggable Plus (SFP+) uplinks
●
Dual field-replaceable power supplies, providing power redundancy and uninterrupted operation
●
Field-replaceable dual-fan module with reversible airflow (front-to-back or back-to-front) and cooling
redundancy
●
USB storage interface for file backup, distribution, and simplified operations
●
Mini-USB console port on the front of the switch for easy management access
●
LAN Lite software features to meet ToR Layer 2 switching requirements
●
1-year limited warranty
Switch Configuration
Table 1 shows the configuration information for the Cisco Catalyst 2360 Series.
Table 1.
Cisco Catalyst 2360 Series Configuration
Switch Model
Description
Uplinks
Cisco Catalyst 2360 Series switches with 10 Gigabit uplinks and 10/100/1000-Gbps Ethernet connectivity
Cisco Catalyst 2360-48TD-S Switch
48X Ethernet 10/100/1000-Gbps ports
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
4X 10 Gigabit Ethernet Small Form-Factor Plus
Pluggable (SFP+) ports
Page 1 of 10
Data Sheet
Features and Benefits
Power Supply Redundancy
The Cisco Catalyst 2360 Series can operate on a single hot-swappable power supply but can also accommodate a
second power supply (Figure 2). The second power supply provides power redundancy, and if either power supply
fails, the other power supply transparently takes over switch operation. Both power supplies are hot swappable.
Figure 2.
Cisco Catalyst 2360 Series: Dual Hot-Swappable Power Supplies
Reversible Airflow and Cooling Redundancy
The Cisco Catalyst 2360 Series is cooled by a hot-swappable fan module that is designed with two fans, providing
cooling redundancy. The fan module provides optional front-to-back or back-to-front airflow through the switch.
Airflow direction can be reversed by removing the fan module, rotating it 180 degrees, and reinserting it in the slot.
Figure 3.
Cisco Catalyst 2360 Series: Hot-Swappable Dual-Fan Unit
Dynamic Buffer Allocation
The switch can dynamically allocate additional buffering on ports that experience microburst traffic. All ports are
allocated reserved buffer space and when ports experience bursts of traffic, additional buffering is allocated from a
shared buffer pool.
Sustainability
Cisco Catalyst switching solutions enable greener practices through measurable power efficiency, integrated
®
services, and innovations such as Cisco EnergyWise, an enterprisewide solution that monitors and conserves
energy with customized policies. Together, Cisco EnergyWise technology and Cisco Catalyst switches reduce
greenhouse gas (GhG) emissions and increase energy cost savings and sustainable business behavior.
Sustainability features in the Cisco Catalyst 2360 Series includes the following:
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 10
Data Sheet
●
Cisco EnergyWise technology: Cisco EnergyWise is an innovative architecture added to fixed-configuration
switches, including the Cisco Catalyst 2360 Series, that promotes companywide sustainability by reducing
energy consumption across an entire corporate infrastructure. Cisco EnergyWise enables companies to
measure the power consumption of the network infrastructure and network-attached devices and manage
power consumption with specific policies, reducing power consumption to lower costs.
Cisco EnergyWise encompasses a highly intelligent network-based approach to communicate messages that
measure and control energy between network devices and endpoints. The network discovers Cisco
EnergyWise manageable devices, monitors their power consumption, and takes action based on business
rules to reduce power consumption. The management interface uses standard Simple Network Management
Protocol (SNMP) or TCP to integrate Cisco and third-party management systems.
●
Efficient switch operation: Cisco Catalyst 2360 Series switches, designed and engineered by Cisco,
provides significant power savings through low-power operation for industry best-in-class and power
consumption capabilities. The Cisco Catalyst 2360 Series ports offer reduced-power modes so that a port not
in use can move into a lower power utilization state.
Easy-to-Use Deployment and Control Features
The Cisco Catalyst 2360 Series helps reduce operating costs through the following features:
●
Autonegotiation on all ports automatically selects half- or full-duplex transmission mode to optimize
bandwidth.
●
Dynamic Trunking Protocol (DTP) facilitates dynamic trunk configuration across all switch ports.
●
Port Aggregation Protocol (PAgP) automates the creation of Gigabit EtherChannel groups to link to another
switch, router, or server.
●
Link Aggregation Control Protocol (LACP) allows the creation of Ethernet channeling with devices that
conform to IEEE 802.3ad. This feature is similar to Cisco EtherChannel technology and PAgP.
●
Automatic media-dependent interface crossover (MDIX) automatically adjusts transmit and receive pairs if an
incorrect cable type (crossover or straight-through) is installed.
●
Unidirectional Link Detection Protocol (UDLD) and Aggressive UDLD allow unidirectional links caused by
incorrect fiber-optic wiring or port faults to be detected and disabled on fiber-optic interfaces.
●
Internet Group Management Protocol (IGMP) snooping for IPv4 and IPv6 Multicast Listener Discovery (MLD)
v1 and v2 snooping provide fast client joins and leaves of multicast streams and limit bandwidth-intensive
video traffic to only the requestors.
●
Per-port broadcast, multicast, and unicast storm control prevent faulty end stations from degrading overall
system performance.
●
Cisco VLAN Trunking Protocol (VTP) supports dynamic VLANs and dynamic trunk configuration across all
switches.
●
Switch Port Analyzer (SPAN) allows administrators to monitor ports in a Layer 2 switch network from any
other switch in the same network.
●
For enhanced traffic management, monitoring, and analysis, the Embedded Remote Monitoring (RMON)
software agent supports four RMON groups (history, statistics, alarms, and events).
●
Trivial File Transfer Protocol (TFTP) reduces the cost of administering software upgrades by downloading
from a centralized location.
●
Network Timing Protocol (NTP) provides an accurate and consistent timestamp to all intranet switches.
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 10
Data Sheet
●
Cisco Emergency Responder (CER) enhances emergency calling from Cisco Unified Call Manager, helping
ensure that Cisco Unified Call Manager sends emergency calls to the appropriate public safety answering
point (PSAP) for the caller's location.
Advanced Intelligent Network Management Tools
The Cisco Catalyst 2360 Series offers both a superior command-line interface (CLI) for detailed configuration tasks
and Cisco Network Assistant software, a PC-based tool for quick configuration based on preset templates. In
addition, the CiscoWorks LAN Management Solution (LMS) supports the Cisco Catalyst 2360 Series for networkwide
management.
●
Cisco Network Assistant: This PC-based network management application designed for small and mediumsized business (SMB) networks with up to 250 users offers centralized network management and
configuration capabilities. This application also provides an intuitive GUI through which users can easily apply
common services across Cisco switches, routers, and access points, such as:
◦
Configuration management
◦
Troubleshooting advice
◦
Inventory reports
◦
Event notification
◦
Network security settings
◦
Password synchronization
◦
Drag-and-drop Cisco IOS Software upgrades
®
For detailed information about Cisco Network Assistant, visit http://www.cisco.com/go/cna.
●
CiscoWorks LMS: This comprehensive network lifecycle management solution provides an extensive library
of easy-to-use features to automate the initial and day-to-day management of your Cisco network
infrastructure. CiscoWorks LMS uniquely uses Cisco hardware and software platform knowledge and
operating experience to provide a powerful set of work-flow focused configuration, monitoring,
troubleshooting, reporting, and administrative tools, including:
◦
Support for new Cisco hardware platforms the day they ship
◦
Support for new technologies and services, such as Cisco EnergyWise technology, from initial deployment
to day-to-day administration and management
◦
Configuration management tools built on the basis of Cisco experience and Cisco Validated Design
recommendations
◦
Monitoring and troubleshooting capabilities that incorporate Cisco hardware best practices and diagnostic
features
◦
Automated management of hardware inventories, security vulnerabilities (through product security incident
response teams [PSIRTs]), and platform end-of-life and support cycles
For detailed information about CiscoWorks LMS, go to
http://www.cisco.com/en/US/products/sw/cscowork/ps2425/index.html.
Security
The Cisco Catalyst 2360 Series LAN Lite switch provides basic security:
●
Static Access Ports
●
Multilevel Console Security to prevent unauthorized users from altering the switch configuration
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 10
Data Sheet
●
Secure Copy Protocol (SCP) to enable network administrators to copy configurations and Cisco IOS Software
images through encrypted channels
●
Secure Shell (SSH) Protocol v2 and SNMPv3, which provide network security by encrypting administrator
traffic during telnet and SNMP sessions; SSHv2 and the cryptographic version of SNMPv3 require a special
cryptographic software image because of U.S. export restrictions
Layer 2 Networking
The Cisco 2360 Series provides Layer 2 networking to enable availability. Features include the following:
●
IEEE 802.1s/w Rapid Spanning Tree Protocol (RSTP) and Multiple Spanning Tree Protocol (MSTP) provide
rapid spanning-tree convergence independent of spanning-tree timers and also offers the benefit of Layer 2
load balancing and distributed processing
●
Per-VLAN Rapid Spanning Tree Plus (PVRST+) allows rapid spanning-tree reconvergence on a per-VLAN
spanning-tree basis, without requiring the implementation of spanning-tree instances
●
Switch-port autorecovery (Errdisable) automatically attempts to reactivate a link that is disabled because of a
network error
●
Up to 128 VLANs and up to 128 spanning-tree instances per switch are supported
Quality of Service
The Cisco Catalyst 2360 Series offers intelligent services that keep everything flowing smoothly. Industry-leading
mechanisms for marking, classification, and scheduling deliver superior performance for data traffic, all at wire
speed. Following are some of the quality-of-service (QoS) features supported in the Cisco Catalyst 2360 Series:
●
IEEE 802.1p class of service (CoS)
●
Four egress queues per port to enable differentiated management of different traffic types across the stack
●
Shaped Round Robin (SRR) scheduling to help ensure differential prioritization of packet flows by intelligently
servicing the ingress and egress queues
Specifications
Tables 2, 3, and 4 list hardware and power specifications for the Cisco Catalyst 2360 Series.
Table 2.
Hardware Specifications for Cisco Catalyst 2360 Series Switches
Performance and Scalability
Forwarding bandwidth
88 Gbps
Flash memory
64 MB
Memory DRAM
128 MB
Maximum VLANs
128
VLAN IDs
4096
Maximum transmission unit (MTU)
Up to 9198 bytes
Jumbo frames
9216 bytes
Resource
Default
QoS
Unicast MAC addresses
8000
8000
8000
IPv4 IGMP groups
256
256
256
IPv4 MAC QoS access control entries
128
384
0
IPv4 MAC security access control entries
384
128
256
Dual
Power Supply
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 10
Data Sheet
● Customers can provide power to a switch only by using the C2360-PWR-135WAC power supply. The connector is located at the back of the
switch. The switch has two power-supply slots.
● The power supply is an autoranging unit.
● The power supply supports input voltages between 100 and 240 VAC.
● Use the supplied AC power cord to connect the AC power connector to an AC power outlet. See Table 7 for a list of supported power cords.
LED Indicators
● Per-port status: Link integrity, disabled, activity, speed, and full duplex
● System status: System, link status, link duplex, and link speed
Dimensions (H x W x D)
Model
Inches
Centimeters
WS-C2360-48TD-S
17.5 x 13.5 x 1.75 in
44.4 x 34.3 x 4.4 cm
C2360-PWR-135WAC
4 x 7.5 x 1.5 in
10.1 x 19.0 x 3.8 cm
C2360-FAN
1.5 x 7.5 x 1.5 in
3.8 x 19.0 x 3.8 cm
Weight
Model
Pounds
Kilograms
WS-2360-48TD-S
13 lb
5.9 kg
C2360-PWR-135WAC
2 lb
0.9 kg
C2360-FAN
0.5 lb
0.22 kg
Environmental Ranges
Fahrenheit
Centigrade
Operating temperature up to 5,000 ft (1,500 m)
0º to 113ºF
-5º to 45ºC
Operating temperature up to 10,000 ft (3,000 m)
23º to 104ºF
-5º to 40ºC
Short-term exception at sea level*
23º to 31ºF
-5º to 55ºC
Short-term exception up to 5,000 feet (1,500 m)*
23º to 122ºF
-5º to 50ºC
Short-term exception up to 10,000 feet (3000 m)*
23º to 113ºF
-5º to 45ºC
Feet
Meters
Operating altitude
Up to 10,000 ft
Up to 3000m
Storage altitude
Up to 13,000 ft
Up to 4000m
Operating relative humidity
10 to 95% noncondensing
Storage relative humidity
10 to 95% noncondensing
* Not more than the following in a 1-year period: 96 consecutive hours, or 360 hours total, or 15 occurrences
Acoustic Noise
Measured per ISO 7779 and declared per ISO 9296. Bystander positions operating mode at 77°F (25°C) ambient.
Sound Pressure
Sound Power
Model
LpA(Typical)
LpAD(Maximum)
LwA (Typical)
LwAD (Maximum)
WS-C2360-48TD-S
40 dB
43 dB
4.9 B
5.2 B
Mean Time Between Failures (MTBF)
With no power supply
With 1 power supply
With 2 power supplies
WS-C2360-48TD-S
302,566 hr
291,987 hr
279,521 hr
C2360-PWR-135WAC
300,000 hr (ambient 40C);
Table 3.
Power Specifications for Cisco Catalyst 2360 Series Switches
Description
Cisco Catalyst 2360 Series Specifications
Model
WS- C2360-48TD-S
100 Percent Throughput with 1 power supply
Measured power consumption
63.475W
10 Percent Throughput with 1 power supply
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
100 Percent Throughput with 2 power supplies
63.177W
10 Percent Throughput with 2 power supply
Page 6 of 10
Data Sheet
Measured power consumption
62.023W
61.311W
0 Percent Throughput with 1 power supply
0 Percent Throughput with 2 power supply
Measured power consumption
62.75W
63.02W
Ports Unconnected, with 1 power supply
Ports unconnected, with 2 power supply
Measured power consumption
34.38W
Table 4.
32.02W
Voltage and Full Power Rating for Power Supply
Model
Voltage (Autoranging)
Current
Frequency
C2360-PWR-135WAC
100 to 240 VAC
2 to 1A rating
50 to 60 Hz
Model
Power Rating
C2360-PWR-135WAC
0.2 kVA
Standards and Safety Compliance
Tables 5 and 6 provide management and standards and safety and compliance information for the Cisco Catalyst
2360 Series.
Table 5.
Description
Management
Standards
Management and Standards Support for Cisco Catalyst 2360 Series Switches
Specification
● BRIDGE-MIB
● CISCO-CABLE-DIAG-MIB
● CISCO-TC-MIB
● CICSO-TCP-MIB
● CISCO-CDP-MIB
● CISCO-CLUSTER-MIB
● CISCO-UDLDP-MIB
● CISCO-VLAN-IFTABLE-RELATIONSHIP-MIB
● CISCO-CONFIG-COPY-MIB
● CISCO-CONFIG-MAN-MIB
● CISCO-VLAN-MEMBERSHIP-MIB
● CISCO-VTP-MIB
● CISCO-ENTITY-VENDORTYPE-OID-MIB
● CISCO-ENVMON-MIB
● ENTITY-MIB
● ETHERLIKE-MIB
● CISCO-ERR-DISABLE-MIB
● CISCO-FLASH-MIB
● IEEE8021-PAE-MIB
● IEEE8023-LAG-MIB
● CISCO-FTP-CLIENT-MIB
● CISCO-IGMP-FILTER-MIB
● IF-MIB
● INET-ADDRESS-MIB
● CISCO-IMAGE-MIB
● CISCO-IP-STAT-MIB
● OLD-CISCO-CHASSIS-MIB
● OLD-CISCO-FLASH-MIB
● CISCO-LAG-MIB
● CISCO-MAC-NOTIFICATION-MIB
● OLD-CISCO-INTERFACES-MIB
● OLD-CISCO-IP-MIB
● CISCO-MEMORY-POOL-MIB
● CISCO-PAGP-MIB
● OLD-CISCO-SYS-MIB
● OLD-CISCO-TCP-MIB
● CISCO-PING-MIB
● CISCO-PORT-QOS-MIB
● OLD-CISCO-TS-MIB
● RFC1213-MIB
● CISCO-PORT-SECURITY-MIB
● CISCO-PORT-STORM-CONTROL-MIB
● RMON-MIB
● RMON2-MIB
● CISCO-POWER-ETHERNET-EXT-MIB
● CISCO-PRODUCTS-MIB
● SNMP-FRAMEWORK-MIB
● SNMP-MPD-MIB
● CISCO-PROCESS-MIB
● CISCO-RTTMON-MIB
● SNMP-NOTIFICATION-MIB
● SNMP-TARGET-MIB
● CISCO-SMI-MIB
● CISCO-STP-EXTENSIONS-MIB
● SNMPv2-MIB
● TCP-MIB
● CISCO-SYSLOG-MIB
● Cisco-UDLDP-MIB
● UDP-MIB
● IEEE 802.1D Spanning Tree Protocol
● IEEE 802.1p CoS Prioritization
● 100BASE-FX (SFP)
● 1000BASE-SX (SFP)
● IEEE 802.1Q VLAN
● IEEE 802.1s Multiple Spanning Tree
● 1000BASE-LX/LH (SFP)
● RMON I and II standards
● IEEE 802.1w Rapid Spanning Tree
● SNMPv1, v2c, and v3
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 10
Data Sheet
Description
Specification
● IEEE 802.1ab (LLDP)
● IEEE 802.3ad (LACP)
● IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX,
and 1000BASE-T ports
● IEEE 802.3 10BASE-T specification
● IEEE 802.3u 100BASE-TX specification
● IEEE 802.3ab 1000BASE-T specification
RFC compliance
● RFC 768 - UDP
● RFC 783 - TFTP
● RFC 1901 - SNMPv2C
● RFC 1902-1907 - SNMPv2
● RFC 791 - IP
● RFC 792 - Internet Control Message Protocol (ICMP)
● RFC 1981 - MTU Path Discovery IPv6
● FRC 2068 - HTTP
● RFC 793 - TCP
● RFC 826 - ARP
● RFC 2131 - DHCP
● RFC 2138 - RADIUS
● RFC 854 - Telnet
● RFC 951 - Bootstrap Protocol (BOOTP)
● RFC 2233 - IF MIBv3
● RFC 2373 - IPv6 Aggregatable Addresses
● RFC 959 - FTP
● RFC 1112 - IP Multicast and IGMP
● RFC 2460 - IPv6
● RFC 2461 - IPv6 Neighbor Discovery
● RFC 1157 - SNMPv1
● RFC 1166 - IP Addresses
● RFC 2462 - IPv6 Autoconfiguration
● RFC 2463 - ICMP IPv6
● RFC 1256 - ICMP Router Discovery
● RFC 1305 - NTP
● RFC 2474 - Differentiated Services (DiffServ)
Precedence
● RFC 2597 - Assured Forwarding
● RFC 1492 - TACACS+
● RFC 1493 - Bridge MIB
● RFC 2598 - Expedited Forwarding
● RFC 2571 - SNMP Management
● RFC 1542 - BOOTP extensions
● RFC 1643 - Ethernet Interface MIB
● RFC 3046 - DHCP Relay Agent Information Option
● RFC 3376 - IGMPv3
● RFC 1757 - RMON
● RFC 3580 - IEEE 802.1X RADIUS
Table 6.
Safety and Compliance
Description
Safety certifications
Specification
● UL 60950-1, Second Edition
● CAN/CSA 22.2 No. 60950-1, Second Edition
● TUV/GS to EN 60950-1, Second Edition
● CB to IEC 60950-1 Second Edition with all country deviations
● CE Marking
● NOM (through partners and distributors)
Electromagnetic emissions certifications (EEC)
● FCC Part 15 Class A
● EN 55022 Class A (CISPR22)
● EN 55024 (CISPR24)
● AS/NZS CISPR22 Class A
● CE
● CNS13438 Class A
● MIC
● GOST
● China EMC Certifications
Environmental
Reduction of Hazardous Substances (ROHS) 6
Telco
Common Language Equipment Identifier (CLEI) code
Warranty
1-year limited warranty
Warranty
Cisco Catalyst 2360 Series switches come with a 1-year limited warranty. The formal warranty statement, including
the warranty applicable to Cisco software, appears in the Cisco information packet that accompanies the Cisco
product. Customers should carefully review the warranty statement shipped with the specific product before use.
Cisco reserves the right to refund the purchase price as its exclusive warranty remedy. For further information about
warranty terms, visit http://www.cisco.com/go/warranty.
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 10
Data Sheet
Software Update Policy
The Cisco Catalyst 2360 Series comes with a single LAN Lite image and will be provided with maintenance updates
and bug fixes designed to maintain the compliance of the software with published specifications, release notes, and
industry standards as long as the original end user continues to own or use the product or for up to 1 year from the
end-of-sale date for this product, whichever occurs earlier. This policy supersedes any previous warranty or software
statement and is subject to change without notice.
Cisco and Partner Services
Organizations can reduce operating costs and power consumption for the Cisco Catalyst 2360 Series by using
intelligent, personalized services from Cisco and our partners. Through a discovery process that begins with
understanding your business objectives, we help you integrate the Cisco Catalyst switch into your architecture and
incorporate network services. Sharing knowledge and leading practices, we support your success every step of the
way as you deploy, incorporate, manage, and scale new technology. Choose from a flexible suite of support services
designed to meet your business needs and help you maintain high-quality network performance while controlling
operating costs. Please go to http://www.cisco.com/go/2360 for service options on the Cisco Catalyst 2360 Series.
Ordering Information
Table 7 provides ordering information for the Cisco Catalyst 2360 Series
Table 7.
Ordering Information for Cisco Catalyst 2360 Series Switches
Part Number
WS-C2360-48TD-S
Description
● 48 Ethernet 10/100/1000
● 4 Ten Gigabit Ethernet SFP+ uplink ports
● LAN Lite software
Cisco Catalyst 2360 Series Spares
C2360-PWR-135WAC=
Catalyst 2360 Series Switches FRU Power Supply
C2360-FAN=
Catalyst 2360 Series Switches FRU Twin Fan Tray
C2360-PWR-COVER=
Catalyst 2360 Series Switches Blank Power Slot Cover
Spare Rack-Mount Kits for the Cisco Catalyst 2360 Series Switches
RCKMNT-1RU=
Spare rack-mount kit for the Cisco Catalyst 2360 Series Switches
RCKMNT-REC-1RU=
1 RU recessed rack-mount kit for the Cisco Catalyst 2360 Series Switches
Power Cords
CAB-AC
AC Power Cord (North America), C13, NEMA 5-15
CAB-ACA
AC Power Cord (China/Australia), C13, AS 3112
CAB-ACC
Power Cord - China
CAB-ACE
AC Power Cord (Europe), C13, CEE 7, 1.5M
CAB-ACI
AC Power Cord (Italy), C13, CEI 23-16, 2.5m
CAB-ACR
AC Power Cord (Argentina), C13, EL 219 (IRAM)
CAB-ACS
AC Power Cord (Switzerland), C13, IEC 60884-1
CAB-ACU
AC Power Cord (UK), C13, BS 1363, 2.5m
CAB-C13-C14-AC
Power cord, C13 to C14 (recessed receptacle)
CAB-IND-10A
10A Power cable for India
CAB-JPN
AC Power Cord (Japan), C13, JIS C 8303, 2.5m
Optical Transceivers for the Cisco Catalyst 2360 Series Switches
SFP-10G-LR=
10GBASE-LR SFP+ module
SFP-10G-SR=
10GBASE-SR SFP+ module
SFP-10G-LRM=
10GBASE-LRM SFP+ module
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 9 of 10
Data Sheet
Part Number
Description
SFP-H10GB-CU1M
10GBASE-CU SFP+ cable (1m)
SFP-H10GB-CU3M
10GBASE-CU SFP+ cable (3m)
SFP-H10GB-CU5M
10GBASE-CU SFP+ cable (5m)
SFP-H10GB-CU7M
10GBASE-CU SFP+ cable (7m)
GLC-LH-SM=
1000BASE-LX/LH SFP transceiver module for MMF and SMF, 1300-nm wavelength
GLC-SX-MM=
1000BASE-SX SFP transceiver module for MMF, 850-nm wavelength
For More Information
Cisco Catalyst 2360 Series Switches - http://www.cisco.com/go/2360.
For more information about Cisco products, contact:
●
United States and Canada: (toll free) 800 553-NETS (6387)
●
Europe: 32 2 778 4242
●
Australia: 612 9935 4107
●
Other: 408 526-7209
●
URL: http://www.cisco.com
Printed in USA
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-599610-01
08/10
Page 10 of 10