The IMPRESSA J7 Manual
The ‘IMPRESSA Manual’ has been awarded the seal of
approval by the independent German Technical Inspection
Agency, TÜV SÜD, due to its easy-to-understand style, its
thoroughness and coverage of safety aspects.
Table of contents
Your IMPRESSA J7
IMPORTANT SAFEGUARDS
4
8
Control elements
Proper Use
10
For your safety
10
The IMPRESSA J7 Manual
13
Symbol description ...................................................................................................................................... 13
1 IMPRESSA J7
14
Connector System© ....................................................................................................................................15
JURA on the internet ....................................................................................................................................15
Knowledge Builder .......................................................................................................................................15
2 Preparing and using for the first time
16
Supplied as standard ...................................................................................................................................16
Setting up ......................................................................................................................................................16
Filling the water tank ...................................................................................................................................16
Filling the bean container ...........................................................................................................................17
First-time use ................................................................................................................................................17
Inserting and activating the filter..............................................................................................................18
Determining and adjusting the water hardness.....................................................................................19
Adjusting the grinder .................................................................................................................................20
Switching on .................................................................................................................................................21
Switching off ................................................................................................................................................ 22
3 Familiarising yourself with the control options
23
Preparation at the touch of a button....................................................................................................... 23
One-off settings before and during preparation ...................................................................................24
Setting the water for the cup size ............................................................................................................26
Permanent settings in programming mode ..........................................................................................26
4 Preparation at the touch of a button
29
Ristretto, espresso and coffee ...................................................................................................................29
Cappuccino...................................................................................................................................................30
Pre-ground Coffee .......................................................................................................................................31
Foaming and heating milk with the Professional Cappuccino Frother ............................................. 32
Foaming milk with the Easy Cappuccino Frother ................................................................................. 33
Hot water ......................................................................................................................................................34
2
Table of contents
5
Permanent settings in programming mode
35
Products ........................................................................................................................................................ 35
Energy Save Mode ......................................................................................................................................36
Automatic switch-off .................................................................................................................................. 37
Rinsing...........................................................................................................................................................38
Restore factory settings .............................................................................................................................38
Viewing information and maintenance status ......................................................................................39
Unit, amount of water ................................................................................................................................40
Language .......................................................................................................................................................41
6 Maintenance
42
Maintenance tips .........................................................................................................................................42
Rinsing the machine ...................................................................................................................................42
Changing the filter ......................................................................................................................................43
Cleaning the machine ................................................................................................................................45
Descaling the machine...............................................................................................................................46
Rinsing the cappuccino frother ................................................................................................................48
Cleaning the cappuccino frother ..............................................................................................................49
Dismantling and rinsing the Professional Cappuccino Frother ...........................................................51
Dismantling and rinsing the Easy Cappuccino Frother.........................................................................51
Cleaning the bean container ......................................................................................................................51
Descaling the water tank ...........................................................................................................................52
7 Display messages
53
8 Troubleshooting
55
9 Transport and environmentally neutral disposal
57
Transport / Emptying the system............................................................................................................. 57
Disposal......................................................................................................................................................... 57
10 Technical data
58
Index
59
JURA contact details / Legal information
64
3
Important Safeguards
IMPORTANT SAFEGUARDS
These safeguards apply for machines with UL safety test (see rating
plate and chapter 10, ‘Technical data’).
Follow the basic safety
precautions
When using electrical appliances, basic safety precautions should
always be followed, to reduce the risk of fire, electric shock, and/or
injury to persons, including the following:
Z Read all instructions.
Z Do not touch hot surfaces. Use handles or knobs.
Z To protect against fire, electric shock and injury to persons, do
not immerse cord, plugs, or body of machine in water or other
liquid.
Z Close supervision is necessary when any appliance is used by
or near children.
Z Unplug from outlet when not in use and before cleaning.
Allow to cool before putting or taking off parts, and before
cleaning the appliance.
Z Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to the nearest authorized service
facility for examination, repair or adjustment.
Z The use of accessory attachement not recommended by the
appliance manufacturer may result in fire, electric shock, or
injury to persons.
Z Do not use outdoors.
Z Do not let the cord hang over the edge of a table or counter,
or touch hot surfaces.
Z Do not place on or near a hot gas or electric burner, or in a
heated oven.
Z Always attach plug to appliance first, then plug cord into the
wall outlet. To disconnect, turn any control to ‘OFF’ then
remove plug from wall outlet.
Z Do not use appliance for other than intented use.
Z Use extreme caution when dispensing hot steam.
Z For household use only.
SAVE THESE INSTRUCTIONS
4
Important Safeguards
Special cord set instructions
a. A short power supply cord is provided to reduce the risk
resulting from becoming entangled in or tripping over a long
cord.
Your IMPRESSA has a 3-pin grounded plug.
b. Longer extension cords are available and may be used if care
is exercised in their use.
c. If an extension cord is used,
1. the marked electrical rating of the extension cord should be
at least as great as the electrical rating of the appliance,
and
2. if the appliance is of the grounded type, the extension cord
should be a grounding type 3-wire cord, and
3. the longer cord shall be arranged so that it will not drape
over the counter top or tabletop where it can be pulled on
by children of tripped over.
Z
Z
Z
As a safety feature, this plug will fit in a polarized outlet only
one way.
If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician.
Do not modify the plug in any way or attempt to defeat this
safety feature.
Warning
To reduce the risk of fire or electric shock, do not remove any service
covers. No user serviceable parts inside. Repair should be done by
authorized personnel only.
Caution
This appliance is for household use. Any servicing other than cleaning and user maintenance should be performed by an authorized
service representative:
Z Do not immerse base in water or try to disassemble.
Z To reduce the risk of fire or electric shock, do not remove the
base. No user serviceable parts inside. Repair should be done
by authorized service personnel only.
Z Check voltage to be sure that the voltage indicated on the
name plate agreees with your voltage.
Z Never use warm or hot water to fill the water container! Use
cold water only.
5
Important Safeguards
Z
Z
NEVER DO
(or you will void your
warranty protection):
Z
Z
Z
Z
6
Keep your hands and the cord away from hot parts of the
appliance during operation.
Never clean with scouring powders or hard implements.
Never fill instant coffee, chocolate mix etc. into the grinder or
ground coffee funnel (grinder by-pass). It will damage the
functioning of the brewing chamber.
Never fill sugar coated coffee beans into the bean hopper. In
case of doubt, call your dealer.
Never fill anything other than coffee beans into the bean container (no chocolate, no rice, no nuts, no spices, nothing other
than roasted coffee beans).
Never do anything with the machine which is not described in
the User‘s Manual. In case of doubt, call your dealer.
Important Safeguards
7
Control elements
Control elements
8
9
1
10
2
3
11
4
12
13
5
14
6
7
15
Figure: IMPRESSA J7 Piano Black
1
2
3
4
5
6
7
Bean container cover
Water tank cover
Bean container with aroma preservation
cover
Water tank
Height- and width-adjustable coffee spout
Coffee grounds container
Drip tray
8
9
10
11
12
13
14
15
8
Filler funnel for pre-ground coffee
Grinder adjustment switch
Storage compartment cover
Storage compartment with measuring
spoon for pre-ground coffee and
hot water nozzle
Connector System© for removable
frothers and nozzles
Professional Cappuccino Frother
Power switch and mains cable
(side of machine)
Cup platform
Control elements
1
2
3
4
Surface of the machine:
1
Q On/off button
2
Rotary Switch
3
c Maintenance button
Front:
4
Display
. Start symbol
u Ristretto symbol
i Espresso symbol
o Coffee symbol
;
Mild
: Normal
_ Strong
m Hot water symbol
n Steam symbol
The Connector System© permits the use of different frothers and nozzles. These are available from
stockists.
5
6
7
5
6
7
Easy Cappuccino Frother
Professional Cappuccino Frother
Hot water nozzle
9
Important information
Proper Use
The machine is designed and intended for private domestic use. It
should only be used for coffee preparation and to heat milk and
water. Use for any other purpose will be deemed improper. JURA
Elektroapparate AG cannot accept any responsibility for the consequences of improper use.
Before using the machine always read this manual thoroughly and
completely and comply with the instructions it contains. Keep this
IMPRESSA Manual close to the machine and pass it on to the next
user if applicable.
For your safety
10
Please carefully read and observe the important safety information
set out below.
To avoid danger of potentially fatal electric shock:
Z Never use a machine which is damaged or has a defective
mains cable.
Z In the event of signs of damage, for example if there is a smell
of burning, unplug the machine immediately from the mains
supply and contact JURA service.
Z If the mains cable of this machine is damaged, it must be
repaired either directly by JURA or by an authorised JURA
service centre.
Z Make sure that the IMPRESSA and the mains cable are not
located close to hot surfaces.
Z Be careful to ensure that the mains cable does not get caught
and does not rub against sharp edges.
Z Never open and repair the machine yourself. Do not modify
the machine in any way that is not described in the IMPRESSA
Manual. The machine contains live parts. If opened, there is a
danger of potentially fatal injury. Repairs may only be carried
out by authorised JURA service centres, using original spare
parts and accessories.
Important information
There is a risk of scalds or burns on the spouts or the frother:
Z Place the machine out of the reach of children.
Z Do not touch any hot parts. Use the handles provided.
Z Be careful to ensure that the appropriate frother is correctly
installed and clean. The frother or parts of the frother might
come off if the parts are not assembled correctly or a blockage
occurs.
A defective machine is not safe and could cause injury or fire. To
avoid damage and any associated risk of injury or fire:
Z Never allow the mains cable to loosely hang down. The mains
cable could pose a tripping hazard or become damaged.
Z Protect your IMPRESSA from environmental influences such
as rain, frost and direct sunlight.
Z Do not immerse the IMPRESSA, cable or connections in
water.
Z Do not put the IMPRESSA or any individual parts in the dishwasher.
Z Turn your IMPRESSA off at the power switch before any cleaning operation. Always wipe your IMPRESSA with a damp cloth
rather than a wet one, and protect it from prolonged exposure
to water splashes.
Z Only connect the machine to a mains voltage in accordance
with the information on the rating plate. The rating plate is
located on the underside of your IMPRESSA. Further technical
data is given in Chapter 10 ‘Technical Data’.
Z Please only use original JURA maintenance products. Use of
products that are not explicitly recommended by JURA could
damage the IMPRESSA.
Z Do not use any coffee beans treated with additives or caramelised coffee beans.
Z Only fill the water tank with cold, fresh water.
Z Switch the machine off at the power switch if you are going to
be absent for a longer period of time.
11
Important information
People, including children, who
Z do not have the physical, sensory or mental capabilities to use
the machine safely or
Z are inexperienced or lack knowledge in how to use the machine
safely
must be supervised by a responsible person when using it, or must
be instructed in how to use it correctly.
Safety when handling the CLARIS Blue filter cartridge:
Z Filter cartridges should be kept out of the reach of children.
Z Store filter cartridges in a dry place in the sealed packaging.
Z Protect cartridges from heat and direct sunlight.
Z Do not use damaged cartridges.
Z Do not open filter cartridges.
12
The IMPRESSA J7 Manual
The IMPRESSA J7 Manual
You are holding the manual for your IMPRESSA J7 in your hand. It
will help you to familiarise yourself with your IMPRESSA safely and
quickly and teach you the full range of facilities it offers:
Z Chapter 2, ‘Preparing and using for the first time’, explains
step-by-step how to set up and prepare the machine.
Z Chapter 3, ‘Familiarising yourself with the control options’ is
important for you to read as you are familiarising yourself
with your IMPRESSA.
Z All the other chapters are intended to help you when you have
a specific query.
@ You can download the short operating instructions for your
machine from the JURA website (www.jura.com).
Symbol description
Warnings
J
CAUTION
Always take note of any information marked with the words CAUTION or
WARNING and a warning sign. The signal word WARNING draws your attention to potential serious injury, and the signal word CAUTION to potential
minor injury.
CAUTION
CAUTION draws your attention to potential damage to the machine.
Symbols used
E
Information and tips to make it even easier to use your IMPRESSA.
@
References to the JURA website, which provides further information that may
be of interest to you: www.jura.com
T
Prompt to take action. This symbol means that you are being prompted to
perform some action.
READY
Display message
13
1 IMPRESSA J7
1
IMPRESSA J7
Perfect Enjoyment,
Perfect Aesthetics
14
The uncompromising all-round design of the IMPRESSA J7 indulges
the eyes as well as the taste buds. Gourmets will find plenty to
delight them as their coffee dreams come true and they experience
a new dimension of enjoyment with ristretto, espresso, coffee
crème, cappuccino, latte macchiato and many other trendy specialities. This is easy to achieve, because the innovative operating concept leaves nothing to be desired when it comes to simplicity. And
the integrated cup illumination places every speciality coffee in the
right light.
Z
Breathtakingly beautiful: Clear, no-frill contours and highquality materials set the tone of the design of the IMPRESSA
J series. All details have been exactly thought out and come
together to form an aesthetic whole that impresses in every
way. This makes the IMPRESSA J7 a true design feature in the
home, which, thanks to its compact design, can easily be
placed anywhere.
Z
Pure ergonomics: The centrally arranged control elements,
with the unique Rotary Switch and a plain text display which
speaks your language, will allow you to quickly and intuitively
make your coffee wishes come true. The focus is fully on your
personal taste. Simply select the coffee strength, amount of
water and temperature according to your individual preferences. You can even choose between three hot water temperature levels. Accessories such as the measuring spoon and the
hot water nozzle can be conveniently stored in the storage
compartment where they are always within reach.
Z
Energy-saving made easy: The IMPRESSA J7 actively assists
you in saving energy.
U With the Energy Save Mode (E.S.M.©) you can adjust the
energy saving potential to suit the way you like to enjoy your
beverages.
1 IMPRESSA J7
U Zero-Energy Switch: When the IMPRESSA is switched off
with the on/off button, the machine is completely disconnected from the power supply.
Z
Height- and width-adjustable coffee spout: The height- and
width-adjustable coffee spout is another JURA innovation. It
allows precise adaptation to cups of different heights and
diameters. This prevents the coffee from splashing and produces a delicious crema with the ideal consistency.
Connector System©
The Connector System© permits the use of different cappuccino
frothers:
Z Professional Cappuccino Frother
U Cappuccino, latte macchiato
U Hot milk and milk foam
Z Easy Cappuccino Frother
U Cappuccino
U Milk foam
JURA on the internet
Visit us on the internet.
@ At www.jura.com you will find interesting and up-to-date
information on your IMPRESSA and on every aspect of
coffee.
Knowledge Builder
You can familiarise yourself with your IMPRESSA in a fun way on the
PC.
@ The Knowledge Builder awaits you at www.jura.com. The
interactive assistant, LEO, will assist you and explain the benefits of and how to use your IMPRESSA.
15
2 Preparing and using for the first time
2 Preparing and using for the first time
This chapter provides you with the information you need to use your
IMPRESSA without any problems. You will prepare your IMPRESSA
step-by-step to enjoy your first perfect cup of coffee.
Supplied as standard
The following items are supplied as standard:
Z Your JURA IMPRESSA J7 automatic coffee machine
Z The Welcome Pack, which includes:
U The IMPRESSA J7 Manual
U JURA cleaning tablets
U Measuring spoon
U Hot water nozzle
U Aquadur®test strip
U CLARIS Blue extension
U CLARIS Blue filter cartridge
U JURA Cappuccino Cleaner
Setting up
Keep the packaging for your IMPRESSA. It should be used to protect
the machine during transport.
When setting up your IMPRESSA, please note the following:
Z Set the IMPRESSA down on a horizontal surface that is not
sensitive to water.
Z Choose a spot for your IMPRESSA which is protected against
overheating.
Filling the water tank
CAUTION
To enjoy the perfect cup of coffee we recommend changing the
water every day.
Milk, mineral water or other liquids can damage the water tank or
the machine.
T Only fill the water tank with fresh, cold water.
T Open the water tank cover.
T Remove the water tank and rinse it with cold water.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Close the water tank cover.
16
2 Preparing and using for the first time
Filling the bean
container
The bean container has an aroma preservation cover. This will ensure
that your coffee beans retain their aroma for longer.
CAUTION
Coffee beans which have been treated with additives (e.g. sugar),
pre-ground coffee or freeze-dried coffee will damage the grinder.
T Only use untreated coffee beans to refill the bean container.
T Open the bean container cover and remove the aroma preservation cover.
T Remove any dirt or foreign objects inside the bean container.
T Fill the bean container with coffee beans, then close the
aroma preservation cover and the bean container cover.
First-time use
WARNING
If the machine is operated with a defective mains cable, there is a
danger of potentially fatal electric shock.
T Never use a machine which has a defective mains cable.
Precondition: The water tank and bean container are full.
T Insert the mains plug into a power socket.
3 T Switch on the IMPRESSA using the power switch on the
right-hand side of the machine.
Q T Press the on/off button to switch the IMPRESSA on.
The Rotary Switch lights up. SPRACHE DEUTSCH
appears on the display.
f T Turn the Rotary Switch until the required language is displayed, for example LANGUAGE ENGLISH.
k T Press the Rotary Switch to confirm the language.
OK appears briefly on the display to confirm the setting.
PRESS RINSE, the maintenance button c lights up.
T Place a receptacle under the frother.
c T Press the maintenance button.
SYSTEM FILLING, the system fills up with water.
A small amount of water flows from the frother.
This operation stops automatically, the following appears on
the display: HEATING.
PRESS RINSE, the maintenance button c lights up.
17
2 Preparing and using for the first time
T Place a receptacle under the coffee spout.
c T Press the maintenance button.
RINSING, the machine rinses. The operation stops automatically.
READY appears on the display. Your IMPRESSA is ready for
use.
Inserting and
activating the filter
Your IMPRESSA no longer has to be descaled if you are using CLARIS
Blue filter cartridges.
@ You can also try out the ‘Inserting the filter’ operation online.
Visit the Knowledge Builder at www.jura.com.
E Perform the ‘Inserting the filter’ operation without interruptions. This will ensure that your IMPRESSA always produces its
best.
Precondition: READY is displayed.
k T Keep the Rotary Switch pressed until RINSE appears on
the display.
g T Turn the Rotary Switch until FILTER - is displayed.
k T Press the Rotary Switch to enter the programme item.
NO g T Turn the Rotary Switch until YES w is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display to confirm the setting.
INSERT, the maintenance button c lights up.
T Remove the filter cartridge extension from the Welcome Pack.
T Fit the extension on top of an original CLARIS Blue filter
cartridge.
T Remove and empty the water tank.
T Lift the cartridge holder and insert the filter cartridge into
the water tank, exerting slight pressure.
T Close the cartridge holder. It will click into place audibly.
E After two months, the filter will cease to work. You can check
the elapsed time by referring to the date plate on the cartridge
holder in the water tank.
18
2 Preparing and using for the first time
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Place a receptacle (at least 500 ml) under the frother.
E If you are using the Professional Cappuccino Frother, set the
selector switch of the frother to the steam position n.
c T Press the maintenance button.
FILTER RINSING. Water flows out of the frother.
E You can interrupt rinsing of the filter at any time by pressing
the maintenance button c.
E The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
500 ml. HEATING appears on the display, then READY is
displayed. The filter is now activated.
Determining and
adjusting the
water hardness
E If you are using the CLARIS Blue filter cartridge and have activated it in programming mode, you will not be able to adjust
the water hardness.
The harder the water is, the more frequently the IMPRESSA needs to
be descaled. It is therefore important to adjust the water hardness.
The water hardness can be adjusted on a continuous scale between
1° dH and 30° dH. This can also be deactivated, which means that
the IMPRESSA will not let you know when it has to be descaled.
Determining the water
hardness
You can find out what the water hardness is by using the Aquadur®
test strip supplied as standard.
T Hold the test strip briefly (for one second) under flowing
water. Shake off the water.
T Wait for about one minute.
T You will then be able to read the degree of water hardness
from the discolouration of the Aquadur®test strip and the
description on the packaging.
You can now adjust the water hardness.
19
2 Preparing and using for the first time
Adjusting the water
hardness
Example: Proceed as follows to change the water hardness from
16°dH to 25°dH.
Precondition: READY is displayed.
k T Keep the Rotary Switch pressed until RINSE appears on
the display.
g T Turn the Rotary Switch until HARDNESS is displayed.
k T Press the Rotary Switch to enter the programme item.
16°dH
g T Turn the Rotary Switch until 25°dH is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display to confirm the setting.
HARDNESS
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
READY appears on the display.
Adjusting the grinder
CAUTION
You can adjust the grinder on a continuous scale to suit the roast
of your coffee.
If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is running.
The consistency of grind setting is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.
Our recommendations:
Z Select a fine setting for a light roast.
U If the consistency of grind is too fine, the coffee only flows
in drips from the coffee spout.
20
2 Preparing and using for the first time
Z
Select a coarse setting for a darker roast.
U If the consistency of grind is too coarse, the coffee flows too
quickly from the coffee spout.
Example: Proceed as follows to change the consistency of grind
during the preparation of an espresso.
T Open the cover of the storage compartment.
T Place a cup under the coffee spout.
i T Touch the Espresso symbol.
1ESPRESSO is displayed for about two seconds and the
Espresso symbol is active.
READY
. T Touch the Start symbol.
The grinder starts and 1 ESPRESSO appears on the
display.
T Turn the grinder adjustment switch to the desired position
while the grinder is running.
The coffee will be prepared and the consistency of grind is
adjusted.
T Close the cover of the storage compartment.
Switching on
Precondition: Your IMPRESSA is switched on at the power switch.
Q T Press the on/off button to switch the IMPRESSA on.
HEATING appears on the display.
PRESS RINSE, the maintenance button c lights up.
T Place a receptacle under the coffee spout.
c T Press the maintenance button.
RINSING, the machine rinses.
The operation stops automatically. READY appears on the
display.
21
2 Preparing and using for the first time
Switching off
When you switch your IMPRESSA off, the coffee spout is only rinsed
if you have prepared a speciality coffee.
T Place a receptacle under the coffee spout.
Q T Press the on/off button.
RINSING, the coffee spout is rinsed.
The IMPRESSA is switched off.
22
3 Familiarising yourself with the control options
3 Familiarising yourself with the control options
With the IMPRESSA, you can prepare an excellent coffee or milk speciality at the touch of a button. You also have the option of adjusting
the coffee strength and temperature, as well as the amount of water
to your personal taste.
This chapter will allow you to become familiar with all control options
with the aid of examples. To familiarise yourself with your IMPRESSA,
we recommend that you make a point of actively trying the facilities
described in this chapter. You will find this is well worthwhile.
Familiarise yourself with the following control options:
Z Preparation at the touch of a button
Z One-off settings before and during preparation
Z Entering a permanent setting for the amount of water for the
cup size
Z Permanent settings in programming mode
E You can interrupt the machine at any time while a speciality
coffee, hot water or steam is being prepared. To do this, press
the Rotary Switch k or the maintenance button c or touch
the Start symbol ..
E The last product prepared and the corresponding coffee
strength are always active.
@ If you prefer to familiarise yourself with your IMPRESSA in a
fun way on the computer, the interactive Knowledge Builder
tutorial program can be found on the Internet at
www.jura.com.
Preparation at the
touch of a button
Prepare your favourite speciality coffee at the touch of a button.
All speciality coffees are prepared following this model at the touch
of a button.
23
3 Familiarising yourself with the control options
Preparing a speciality coffee
at the touch of a button
Example: Proceed as follows to prepare one espresso.
Precondition: READY is displayed.
T Place an espresso cup under the coffee spout.
i T Touch the Espresso symbol.
1 ESPRESSO is displayed for about two seconds. The
Espresso symbol is active.
READY
. T Touch the Start symbol.
Preparation will now begin. 1 ESPRESSO appears on the
display. The pre-set amount of water flows into the cup. You
can follow the current status of preparation on the progress
bar.
Preparation stops automatically and READY appears on
the display.
Preparing two speciality
coffees at the touch of a
button
Example: Proceed as follows to prepare two espressi.
Precondition: READY is displayed.
T Place two espresso cups under the coffee spout.
i T Touch the Espresso symbol twice (within two seconds).
2 ESPRESSI appears on the display.
. T Touch the Start symbol within two seconds while
2 ESPRESSI is displayed.
Preparation will now begin. The pre-set amount of water
flows into the cups. You can follow the current status of
preparation on the progress bar.
Preparation stops automatically and READY appears on
the display.
One-off settings before
and during preparation
You can change the coffee strength before preparation. The following coffee strengths can be selected for 1 ristretto, 1 espresso and
1 coffee:
Z Mild ;
Z Normal :
Z Strong _
E The pre-set amount of water can be changed during preparation by turning the Rotary Switch.
24
3 Familiarising yourself with the control options
One-off settings before and during preparation always follow this
model.
Changing the coffee
strength before preparation
Example: Proceed as follows to prepare a strong cup of coffee.
Precondition: READY is displayed.
T Place a cup under the coffee spout.
_ T Touch the Strong symbol.
STRONG is displayed for about two seconds. The Strong
symbol is active.
o T Touch the Coffee symbol.
1 COFFEE is displayed for about two seconds. The Coffee
symbol is active.
READY
. T Touch the Start symbol.
Preparation will now begin. 1 COFFEE appears on the display. The pre-set amount of water flows into the cup. You
can follow the current status of preparation on the progress
bar.
Preparation stops automatically and READY appears on
the display.
Changing the amount of
water during preparation
Example: Proceed as follows to prepare a 110 ML cup of coffee.
Precondition: READY is displayed.
T Place a cup under the coffee spout.
o T Touch the Coffee symbol.
1 COFFEE is displayed for about two seconds. The Coffee
symbol is active.
READY
. T Touch the Start symbol.
Preparation will now begin. 1 COFFEE appears on the
display.
g T Turn the Rotary Switch during preparation until 110 ML is
displayed.
The set amount of water flows into the cup.
Preparation stops automatically and READY appears on
the display.
25
3 Familiarising yourself with the control options
Setting the water for
the cup size
It is easy to make permanent settings for the amount of water for all
speciality coffees as well as hot water and steam according to the
cup size. As in the following example, adjust the amount of water
once. Every time you prepare a drink in the future, this amount of
water will be dispensed.
The permanent settings for adapting the amount of water to the cup
size for all speciality coffees, hot water and steam follow this
model.
Example: Proceed as follows to make permanent settings for the
amount of water for a coffee.
Precondition: READY is displayed.
T Place a cup under the coffee spout.
o T Touch the Coffee symbol.
1 COFFEE is displayed for about two seconds. The Coffee
symbol is active.
READY
. T Touch the Start symbol for about three seconds, until
ENOUGH COFFEE ? appears on the display.
Preparation starts and the coffee flows into the cup.
. T Touch the Start symbol as soon as there is sufficient coffee
in the cup.
Preparation stops. OK appears briefly on the display. The set
amount of water for one coffee will be permanently stored.
READY appears on the display.
E You can alter these settings at any time by repeating the
above procedure.
E You can also make permanent settings for the amount of
water for all speciality coffees in programming mode, in the
BUTTONS programme item.
Permanent settings in
programming mode
26
You can make permanent settings in programming mode. For
example, you can change product settings such as aroma and the
amount of water or activate an energy saving mode.
Simply by turning and pressing the Rotary Switch you can navigate
through the easy-to-understand programme items and make permanent settings.
3 Familiarising yourself with the control options
You can make the following settings with the Rotary Switch:
Programme item
Sub-item
Explanation
RINSE
RINSE,
CLEAN,
FILTER (only if filter
T Select the desired maintenance programme.
If no action is taken, programming mode is
exited automatically after approximately five
seconds.
is activated),
DE-SCALE (only if filter
is not activated)
BUTTONS
SELECT BUTTON
T Select your settings for speciality coffees,
hot water and steam.
FILTER -
YES w
NO -
T Indicate whether you operate your
IMPRESSA with or without a CLARIS Blue filter
cartridge.
HARDNESS
INACTIVE,
1° dH – 30° dH
T Adjust the water hardness.
ENERGY
SAVE -,
SAVE w
T Select an energy saving mode.
OFF AFTER
INACTIVE,
15 MIN,
0.5 HRS – 15 HRS
T Set the time after which the IMPRESSA
should switch off automatically.
RINSING
MANUAL,
AUTOMATIC
T Set whether the switch-on rinse should be
started manually or automatically.
RESET
PRODUCT,
ALL PROD.,
RESET ALL
T Reset the permanently set values of all
products to the factory settings.
(only if filter is
not activated)
T Keep track of all prepared products and
view the maintenance status.
INFO
DISPLAY
ML, OZ
T Select the unit for the amount of water.
LANGUAGE
T Select your language.
EXIT
T Exit programming mode.
27
3 Familiarising yourself with the control options
Settings in programming mode always follow the same model.
Example: Proceed as follows to change the aroma of one espresso
from INTENSIVE to STANDARD.
Precondition: READY is displayed.
k T Keep the Rotary Switch pressed until RINSE appears.
g T Turn the Rotary Switch until BUTTONS is displayed.
k T Press the Rotary Switch to enter the programme item.
SELECT BUTTON
E Next select the product for which you would like to make
settings.
E To enter a setting for the double product, touch the corresponding symbol twice within a period of two seconds.
i T Touch the Espresso symbol.
1 ESPRESSO is displayed for about two seconds.
WATER
g T Turn the Rotary Switch until STRENGTH is displayed.
k T Press the Rotary Switch to enter the programme item.
INTENSIVE
g T Turn the Rotary Switch until STANDARD is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display to confirm the setting.
STRENGTH
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
BUTTONS
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
READY
28
4 Preparation at the touch of a button
4 Preparation at the touch of a button
In this chapter you will find out how to prepare coffee and milk
specialities and hot water without making further settings.
Chapter 3, ‘Familiarising yourself with the control options’, will teach
you how to adjust the settings to your personal preferences. Alternatively, you can use Chapter 5, ‘Permanent settings in programming mode’.
E You can interrupt the machine at any time while a speciality
coffee, hot water or steam is being prepared. To do this, press
the Rotary Switch k or the maintenance button c or touch
the Start symbol ..
E You can select the coffee strength of individual products
before preparation: mild ;, normal : or strong _.
E During preparation, you can change the pre-set amount of
water by turning the Rotary Switch.
@ You can also try out the preparation of speciality coffees
online. Visit the Knowledge Builder at www.jura.com.
Ristretto, espresso
and coffee
All speciality coffees (ristretto u, espresso i and coffee o) are prepared in the same way.
Example: Proceed as follows to prepare one coffee.
T Place a cup under the coffee spout.
o T Touch the Coffee symbol.
1 COFFEE is displayed for about two seconds. The Coffee
symbol is active.
READY
. T Touch the Start symbol.
Preparation will now begin. 1 COFFEE appears on the display. The pre-set amount of water flows into the cup. You
can follow the current status of preparation on the progress
bar.
Preparation stops automatically and READY appears on
the display.
29
4 Preparation at the touch of a button
Preparing two speciality
coffees at the touch of
a button
To prepare two cups of coffee: Place two cups under the coffee spout
and touch the Coffee symbol o twice (within two seconds). Touch
the Start symbol . within two seconds to start preparation.
Cappuccino
For a cappuccino you must first froth the milk using the cappuccino
frother. You then prepare an espresso straight into the milk foam.
E The following procedure applies to both the Professional and
Easy Cappuccino Frothers.
T Remove the protective cover from the frother.
T Attach the milk pipe to the frother.
T Insert the other end of the milk pipe into a milk carton or
connect it to a milk container.
T Place a cup under the frother.
T If you are using the Professional Cappuccino Frother, set
the selector switch to the milk foam position p.
n T Touch the Steam symbol.
HEATING
As soon as the machine has heated up, READY appears.
n T Touch the Steam symbol again.
STEAM, the milk foam is prepared. You can follow the current status of preparation on the progress bar.
Preparation stops automatically when the pre-set amount of
steam is reached.
E The milk foam preparation can be interrupted at any time.
To do this, press the Rotary Switch k or the maintenance
button c or touch the Start symbol ..
E You can prepare more milk foam within about 40 seconds
without having to wait for the machine to heat.
30
4 Preparation at the touch of a button
T Place the cup under the coffee spout.
i T Touch the Espresso symbol.
1 ESPRESSO is displayed for about two seconds. The
Espresso symbol is active.
READY
. T Touch the Start symbol.
Preparation will now begin. 1 ESPRESSO appears on the
display. The pre-set amount of water flows into the cup.
Preparation stops automatically and READY appears on
the display.
To make sure the cappuccino frother always works properly, rinse
and clean it regularly (see Chapter 6, ‘Maintenance – Cappuccino
frother’).
Pre-ground Coffee
You can choose a second coffee variety, for example decaffeinated
coffee, with the filler funnel for pre-ground coffee.
E Never add more than two level measuring spoons of preground coffee.
E Use pre-ground coffee which is not ground too finely. Very
fine coffee can block up the system so that the coffee only
comes out in drips.
E If you did not fill the machine with a sufficient amount of preground coffee, NOT ENOUGH PRE-GROUND is displayed
and the IMPRESSA stops operation.
E The desired speciality coffee must be prepared within approximately one minute after filling with the pre-ground coffee.
Otherwise the IMPRESSA stops the operation and is ready for
use again.
All speciality coffees with pre-ground coffee are prepared following
this model.
Example: Proceed as follows to prepare a cup of coffee using preground coffee.
T Place a cup under the coffee spout.
T Open the cover of the storage compartment, take out the
measuring spoon for pre-ground coffee and close the cover
again.
31
4 Preparation at the touch of a button
T Open the cover of the filler funnel for pre-ground coffee.
FILL PRE-GROUND
T Place one level measuring spoon of pre-ground coffee into
the filler funnel.
T Close the cover of the filler funnel for pre-ground coffee.
SELECT BUTTON
o T Touch the Coffee symbol.
1 COFFEE appears on the display.
. T Touch the Start symbol.
Preparation will now begin. The pre-set amount of water
flows into the cup. You can follow the current status of preparation on the progress bar.
Preparation stops automatically and READY appears on
the display.
Foaming and
heating milk with
the Professional
Cappuccino Frother
T Remove the protective cover from the frother.
T Attach the milk pipe to the frother.
T Insert the other end of the milk pipe into a milk carton or
connect it to a milk container.
T Place a cup under the frother.
T Turn the selector switch of the frother to the milk foam position p.
E If you want to heat the milk, set the selector switch of the
frother to the milk position t.
n T Touch the Steam symbol.
HEATING
As soon as the machine has heated up, READY appears.
n T Touch the Steam symbol again.
STEAM, the milk foam is prepared. You can follow the current status of preparation on the progress bar.
32
4 Preparation at the touch of a button
Preparation stops automatically when the pre-set amount of
steam is reached.
E The milk foam preparation can be interrupted at any time. To
do this, press the Rotary Switch or the maintenance button or
touch the Start symbol.
E You can prepare more milk foam or heat the milk within about
40 seconds without having to wait for the machine to heat.
To make sure the cappuccino frother always works properly, rinse
and clean it regularly (see Chapter 6, ‘Maintenance – Cappuccino
frother’).
Foaming milk with
the Easy Cappuccino
Frother
T Remove the protective cover from the frother.
T Attach the milk pipe to the frother.
T Insert the other end of the milk pipe into a milk carton or
connect it to a milk container.
T Place a cup under the frother.
n T Touch the Steam symbol.
HEATING
As soon as the machine has heated up, READY appears.
n T Touch the Steam symbol again.
STEAM, the milk foam is prepared. You can follow the current status of preparation on the progress bar.
Preparation stops automatically when the pre-set amount of
steam is reached.
E The milk foam preparation can be interrupted at any time. To
do this, press the Rotary Switch or the maintenance button or
touch the Start symbol.
E You can prepare more milk foam within about 40 seconds
without having to wait for the machine to heat.
33
4 Preparation at the touch of a button
To make sure the cappuccino frother always works properly, rinse
and clean it regularly (see Chapter 6, ‘Maintenance – Cappuccino
frother’).
Hot water
To obtain a perfect water flow, use the removable hot water nozzle.
You can find the hot water nozzle under the cover of the storage
compartment.
The following temperatures can be selected for preparing hot
water:
Z Regular
Z Normal
Z Hot
CAUTION
There is a danger of scalding from hot water splashes.
T Avoid direct contact with the skin.
First attach the hot water nozzle:
T Carefully remove the cappuccino frother from the Connector
System©by twisting slightly.
T Open the cover of the storage compartment, take out the
hot water nozzle and close the cover again.
T Attach the hot water nozzle to the Connector System©,
rotating it slightly.
T Place a cup under the hot water nozzle.
m T Touch the Hot water symbol.
WATER appears on the display, and the temperature is
briefly displayed, e.g. NORMAL.
E By touching the Hot water symbol several times (within
approximately 2 seconds) you can set the temperature to
your individual preference. This setting is not saved.
Hot water flows into the cup. You can follow the current
status of preparation on the progress bar.
Preparation stops automatically and READY appears on
the display.
E During preparation, you can change the amount by turning
the Rotary Switch.
34
5 Permanent settings in programming mode
5 Permanent settings in programming mode
Products
With the BUTTONS programme item you can enter individual
settings for all speciality coffees, hot water and steam.
The following permanent settings can be made:
Product
Amount
Strength
Temperature
1 ristretto
25 ML – 240 ML
STANDARD, INTENSIVE
NORMAL, HIGH
2 ristretti
25 ML – 240 ML
–
NORMAL, HIGH
(per cup)
1 espresso
25 ML – 240 ML
STANDARD, INTENSIVE
NORMAL, HIGH
2 espressi
25 ML – 240 ML
–
NORMAL, HIGH
(per cup)
1 coffee
25 ML – 240 ML
STANDARD, INTENSIVE
NORMAL, HIGH
2 coffees
25 ML – 240 ML
–
NORMAL, HIGH
(per cup)
Hot water
25 ML – 240 ML
–
REGULAR, NORMAL,
HOT
Steam
3 SEC – 120 SEC
–
–
Permanent settings in programming mode always follow the same
model.
Example: Proceed as follows to change the amount of water for
1 coffee from 100 ML to 120 ML and the temperature from
NORMAL to HIGH.
k T Keep the Rotary Switch pressed until RINSE appears.
g T Turn the Rotary Switch until BUTTONS is displayed.
k T Press the Rotary Switch to enter the programme item.
SELECT BUTTON
E Next select the product for which you would like to make
settings.
E To enter a setting for the double product, touch the corresponding symbol twice within a period of two seconds.
35
5 Permanent settings in programming mode
o T Touch the Coffee symbol.
1 COFFEE is displayed for about two seconds.
WATER
k T Press the Rotary Switch to enter the programme item.
100 ML (example)
g T Turn the Rotary Switch until 120 ML is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
WATER
g T Turn the Rotary Switch until TEMP. is displayed.
k T Press the Rotary Switch to enter the programme item.
NORMAL
g T Turn the Rotary Switch until HIGH is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
TEMP.
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
BUTTONS
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
READY
Energy Save Mode
36
In the programme item ENERGY you can permanently set an
energy saving mode (Energy Save Mode, E.S.M.©):
Z SAVE U All coffee products as well as hot water can be prepared
without having to wait.
U Before steam preparation, the machine heats up.
Z SAVE w
U Approximately five minutes after the last preparation the
IMPRESSA switches to the energy-saving temperature and is
not in stand-by mode. When the machine is at energysaving temperature, this is indicated on the display by the
message ENERGY ON.
U Before the preparation of coffee, hot water or steam, the
machine heats up.
5 Permanent settings in programming mode
Example: Proceed as follows to change the energy saving mode
from SAVE - to SAVE w.
k T Keep the Rotary Switch pressed until RINSE appears.
g T Turn the Rotary Switch until ENERGY - is displayed.
k T Press the Rotary Switch to enter the programme item.
SAVE g T Turn the Rotary Switch until SAVE w is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
ENERGY w
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
READY
Automatic switch-off
By instructing your IMPRESSA to automatically switch itself off, you
can cut down your energy consumption. If this function is activated,
your IMPRESSA switches off automatically after the pre-set time following the last action on the machine.
E You can set the automatic switch-off to 15 minutes, 0.5 hours
up to 15 hours, or inactive.
Example: Proceed as follows to change the automatic switch-off
from 1 HRS to 15 MIN.
k T Keep the Rotary Switch pressed until RINSE appears.
g T Turn the Rotary Switch until OFF AFTER is displayed.
k T Press the Rotary Switch to enter the programme item.
1 HRS
f T Turn the Rotary Switch until 15 MIN is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
OFF AFTER
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
READY
37
5 Permanent settings in programming mode
Rinsing
You can set whether the switch-on rinse should be started manually
or automatically.
Example: Proceed as follows to specify that the switch-on rinse
should be started automatically after switching on.
k T Keep the Rotary Switch pressed until RINSE appears.
g T Turn the Rotary Switch until RINSING is displayed.
k T Press the Rotary Switch to enter the programme item.
MANUAL
g T Turn the Rotary Switch until AUTOMATIC is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
RINSING
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
READY
Restore factory
settings
In the programme item RESET you can restore various settings to
their factory settings:
Z PRODUCT
U The settings (amount of water, strength, temperature) for
any product can be restored individually to the factory
settings. The corresponding double product is reset at the
same time.
Z ALL PROD.
U The settings (amount of water, strength, temperature) for all
products are restored to the factory settings.
Z RESET ALL
U All customer settings are restored to the factory settings.
The IMPRESSA then switches off.
Example: Proceed as follows to restored the values for ‘Espresso’ to
the factory settings.
k T Keep the Rotary Switch pressed until RINSE appears.
g T Turn the Rotary Switch until RESET is displayed.
k T Press the Rotary Switch to enter the programme item.
PRODUCT
38
5 Permanent settings in programming mode
i T Touch the Espresso symbol.
OK appears briefly on the display, the settings for ‘Espresso’
are restored to the factory settings.
PRODUCT
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
RESET
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
READY
Viewing information
and maintenance
status
In the programme item INFO you can query the following information:
Z Number of prepared speciality coffees, hot water and steam
Z Maintenance status and number of maintenance programmes
performed (cleaning, descaling, changing the filter)
Z Software version
k T Keep the Rotary Switch pressed until RINSE appears.
g T Turn the Rotary Switch until INFO is displayed.
k T Press the Rotary Switch to enter the programme item.
BUTTONS
k T Press the Rotary Switch to enter the programme item.
The total number of the prepared speciality coffees is displayed.
E By touching the individual symbols for the speciality coffees,
hot water and steam, the respective number of prepared
products is displayed.
E To query the number of double products prepared, touch the
corresponding symbol for the speciality coffee twice.
E Open the cover of the filler funnel for pre-ground coffee to
query this number.
k T Press the Rotary Switch to exit the programme item.
BUTTONS
g T Turn the Rotary Switch until CLEAN is displayed.
39
5 Permanent settings in programming mode
E Continue turning the Rotary Switch to switch to the performed descaling and filter change operations.
k T Press the Rotary Switch to enter the programme item.
The number of performed cleaning operations appears on
the display.
E By turning the Rotary Switch, the maintenance status can also
be displayed in addition to the number of performed maintenance programmes. The filled out fields show the maintenance status. Once all fields are filled out, your IMPRESSA will
request the respective maintenance programme.
k T Press the Rotary Switch to exit the programme item.
CLEAN
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit the programme item.
INFO
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
READY
Unit, amount of water
You can change the unit for the amount of water from ‘ml’ to ‘oz’.
Example: Proceed as follows to change the unit for the amount of
water from ML to OZ.
k T Keep the Rotary Switch pressed until RINSE appears.
g T Turn the Rotary Switch until DISPLAY is displayed.
k T Press the Rotary Switch to enter the programme item.
ML
g T Turn the Rotary Switch until OZ is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
DISPLAY
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
READY
40
5 Permanent settings in programming mode
Language
The language of your IMPRESSA is set with this programme item.
Example: Proceed as follows to change the language from
ENGLISH to DEUTSCH.
Precondition: READY is displayed.
k T Keep the Rotary Switch pressed until RINSE appears.
g T Turn the Rotary Switch until LANGUAGE is displayed.
k T Press the Rotary Switch to enter the programme item.
ENGLISH
g T Turn the Rotary Switch until DEUTSCH is displayed.
k T Press the Rotary Switch to confirm the setting.
OK appears briefly on the display.
SPRACHE
g T Turn the Rotary Switch until EXIT is displayed.
k T Press the Rotary Switch to exit programming mode.
BEREIT
41
6 Maintenance
6 Maintenance
Your IMPRESSA has the following integrated maintenance programmes:
Z Rinsing the machine
Z Changing the filter
Z Cleaning the machine
Z Descaling the machine
E Clean or descale the machine or change the filter when you
are prompted to do so.
Maintenance tips
To ensure that you get many years of reliable service out of your
IMPRESSA and to guarantee the optimum coffee quality, the
machine requires daily maintenance.
Proceed as follows:
Z Empty the coffee grounds container and the drip tray. Rinse
them with warm water.
Z Rinse the water tank with clean water.
Z Dismantle and rinse the frother (see Chapter 6, ‘Maintenance
– Dismantling and rinsing the cappuccino frother’).
Z Wipe the surface of the machine with a clean, soft, damp cloth
(e.g. microfibre cloth).
Rinsing the machine
When the IMPRESSA is switched on, a prompt to perform rinsing
appears after heating, or this is automatically started. It can be set
in programming mode whether the switch-on rinse needs to be activated manually or whether the machine automatically activates the
switch-on rinse (see Chapter 5, ‘Permanent settings in programming mode - Rinses’).
When the IMPRESSA is switched off, a rinse operation is automatically initiated.
You can initiate the rinse operation manually at any time.
42
6 Maintenance
Precondition: READY is displayed.
T Place a receptacle under the coffee spout.
k T Keep the Rotary Switch pressed until RINSE appears.
k T Press the Rotary Switch to enter the programme item.
RINSE
k T Press the Rotary Switch to initiate the rinse operation.
RINSING, water flows out of the coffee spout.
Rinsing stops automatically and your IMPRESSA is then
ready for use.
Changing the filter
E After 50 litres of water have flowed through, the filter will
cease to work. Your IMPRESSA will automatically prompt you
to change the filter.
E After two months, the filter will cease to work. You can check
the elapsed time by referring to the date plate on the cartridge
holder in the water tank.
E If the CLARIS Blue filter cartridge is not activated, you will not
be prompted to change the filter.
@ You can also try out the ‘changing the filter’ operation online.
Visit the Knowledge Builder at www.jura.com.
Changing after a prompt
Proceed as follows to change the CLARIS Blue filter cartridge when
prompted to do so by your IMPRESSA.
Precondition: READY / FILTER is displayed and the maintenance button c lights up.
c T Press the maintenance button.
CHANGE
T Remove and empty the water tank.
T Lift the cartridge holder.
T Take out the old filter cartridge and the extension.
T Fit the extension on top of a new filter cartridge.
43
6 Maintenance
T Insert the filter cartridge into the water tank, exerting slight
pressure.
T Close the cartridge holder. It will click into place audibly.
T Fill the water tank with fresh, cold water and reinsert the
tank.
T Place a receptacle (at least 500 ml) under the frother.
E If you are using the Professional Cappuccino Frother, set the
selector switch of the frother to the steam position n.
c T Press the maintenance button.
FILTER RINSING, water will flow out of the frother.
E You can interrupt rinsing of the filter at any time. To this purpose press the maintenance button c.
E The water may be slightly discoloured. This is not harmful to
health and does not affect the taste.
Rinsing of the filter stops automatically after approximately
500 ml. The IMPRESSA heats up and is once more ready for
use.
Changing the filter
manually
You can initiate the ‘Changing the filter’ operation manually.
Precondition: The filter is activated and READY is displayed.
k T Keep the Rotary Switch pressed until RINSE appears.
k T Press the Rotary Switch to enter the programme item.
RINSE
g T Turn the Rotary Switch until FILTER is displayed.
k T Press the Rotary Switch.
CHANGE
T Continue with the second prompt to take action (indicated
by a T), as is described under ‘Changing after a prompt’.
44
6 Maintenance
Cleaning the machine
CAUTION
After 200 coffee preparations or 80 switch-on rinses, the IMPRESSA
will prompt you to clean it.
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
T Use only original JURA maintenance products.
E The cleaning programme only lasts about 20 minutes.
E Do not interrupt the cleaning programme. The quality of
cleaning will be impaired if you do so.
E JURA cleaning tablets are available from stockists.
@ You can also try out the ‘Cleaning the machine’ operation
online. Visit the Knowledge Builder at www.jura.com.
Cleaning after a prompt
Precondition: READY / CLEAN is displayed and the maintenance
button c lights up.
c T Press the maintenance button.
EMPTY TRAY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
PRESS RINSE, the maintenance button c lights up.
T Place a receptacle under the coffee spout.
c T Press the maintenance button.
CLEANING, water flows out of the coffee spout.
The operation is interrupted, ADD TABLET.
T Open the cover of the filler funnel for pre-ground coffee.
T Insert a JURA cleaning tablet into the filler funnel.
T Close the cover of the filler funnel.
PRESS RINSE, the maintenance button c lights up.
c T Press the maintenance button.
CLEANING, water flows out of the coffee spout several
times.
The operation is interrupted, EMPTY TRAY.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
45
6 Maintenance
The cleaning operation is now complete. The IMPRESSA is
once more ready for use.
Manual cleaning
You can initiate the ‘Cleaning the machine’ operation manually.
Precondition: READY is displayed.
k T Keep the Rotary Switch pressed until RINSE appears.
k T Press the Rotary Switch to enter the programme item.
RINSE
g T Turn the Rotary Switch until CLEAN is displayed.
k T Press the Rotary Switch.
EMPTY TRAY
T Continue with the second prompt to take action (indicated
by a T), as is described under ‘Cleaning after a prompt’.
Descaling the machine
CAUTION
46
The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of
calcification depends on the degree of hardness of your water.
If the descaling agent comes into contact with the skin or eyes, this
can cause irritation.
T Avoid contact with the skin or eyes.
T If descaling agent does come into contact with the skin or
eyes, rinse off with clean water. Should you get any descaling
agent in your eye, see a doctor.
CAUTION
If the wrong descaling agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.
T Use only original JURA maintenance products.
CAUTION
If the descaling operation is interrupted, there may be damage to
the machine.
T Allow the descaling programme to run to the end.
CAUTION
If the descaling agent comes into contact with sensitive surfaces,
damage cannot be ruled out.
T Clean up any splashes immediately.
6 Maintenance
E The descaling programme lasts approx. 45 minutes.
E JURA descaling tablets are available from stockists.
E If you use a CLARIS Blue filter cartridge and this is activated,
you will not be prompted to descale.
@ You can also try out the ‘Descaling the machine’ operation
online. Visit the Knowledge Builder at www.jura.com.
Descaling after a prompt
Precondition: READY / DE-SCALE is displayed and the maintenance button c lights up.
c T Press the maintenance button.
EMPTY TRAY
T Empty the drip tray and coffee grounds container and put
them back into the machine.
AGENT IN TANK
T Remove and empty the water tank.
T Completely dissolve the contents of one blister (three JURA
descaling tablets) in a container that holds 500 ml of water.
This may take several minutes.
T Pour the solution into the empty water tank and insert it in
the machine.
AGENT IN TANK, the maintenance button c lights up.
T Remove the cappuccino frother from the Connector
System©.
T Place a receptacle (at least 500 ml) under the Connector
System©.
c T Press the maintenance button.
DE-SCALING
This causes water to flow out of the Connector System©
several times. The maintenance button blinks during the
descaling operation.
The operation stops automatically, EMPTY TRAY.
T Empty the receptacle under the Connector System©.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
FILL WATER TANK
T Remove the water tank and rinse it thoroughly.
47
6 Maintenance
T Fill the water tank with fresh, cold water and reinsert the
tank.
PRESS RINSE, the maintenance button c lights up.
T Replace the cappuccino frother.
T Place a receptacle under the frother and another under the
coffee spout.
c T Press the maintenance button.
DE-SCALING, water flows out of the frother and the
coffee spout.
The operation stops automatically, EMPTY TRAY.
T Empty the drip tray and coffee grounds container and put
them back into the machine.
The descaling operation is now complete. Your IMPRESSA
heats up and is once more ready for use.
E If the descaling operation stops unexpectedly, rinse the water
tank thoroughly.
Manual descaling
You can initiate the ‘Descaling the machine’ operation manually.
Precondition: READY is displayed and the filter is not activated.
k T Keep the Rotary Switch pressed until RINSE appears.
k T Press the Rotary Switch to enter the programme item.
RINSE
g T Turn the Rotary Switch until DE-SCALE is displayed.
k T Press the Rotary Switch.
EMPTY TRAY
T Continue with the second prompt to take action (indicated
by a T), as is described under ‘Descaling after a prompt’.
Rinsing the
cappuccino frother
E This chapter applies to the Professional and Easy Cappuccino
Frothers.
To ensure that the cappuccino frother works perfectly, you should
rinse it with water after every milk preparation. Your IMPRESSA will
not prompt you to rinse the cappuccino frother.
48
6 Maintenance
Precondition: READY is displayed.
T Remove the milk pipe from the milk carton/bottle or the
milk container.
T Fill a receptacle with fresh water and immerse the milk pipe
in it.
T Place a receptacle under the cappuccino frother.
E If you are using the Professional Cappuccino Frother, turn
the selector switch to the milk foam p or milk t position.
n T Touch the Steam symbol.
HEATING
As soon as the machine has heated up, READY appears.
n T Touch the Steam symbol again.
STEAM, the frother and milk pipe are rinsed.
. T Touch the Start symbol as soon as clean water flows out of
the frother.
The operation stops and your IMPRESSA is once more ready
for use.
Cleaning the
cappuccino frother
E This chapter applies to the Professional and Easy Cappuccino
Frothers.
To ensure that the cappuccino frother works perfectly, you should
clean it daily when you have been preparing milk. Your IMPRESSA
will not prompt you to clean the cappuccino frother.
CAUTION
If the wrong cleaning agent is used, the machine could be damaged
and/or traces of detergent could be left behind in the water.
T Use only original JURA maintenance products.
E JURA Cappuccino Cleaner is available from stockists.
@ You can also try out the ‘Cleaning the cappuccino frother’
operation online. Visit the Knowledge Builder at
www.jura.com.
49
6 Maintenance
Precondition: READY is displayed.
T Remove the milk pipe from the milk carton/bottle or the
milk container.
T Pour 250 ml of fresh water into a receptacle and add one
capful (max. 15 ml) of Cappuccino Cleaner.
T Immerse the milk pipe in the receptacle.
T Place another receptacle under the frother.
E If you are using the Professional Cappuccino Frother, turn
the selector switch to the milk foam p or milk t position.
n T Touch the Steam symbol.
HEATING
As soon as the machine has heated up, READY appears.
n T Touch the Steam symbol again.
STEAM, the frother and milk pipe are cleaned.
. T Touch the Start symbol as soon as the receptacle containing
the Cappuccino Cleaner is empty.
T Rinse the receptacle thoroughly, fill it with approx. 250 ml
of fresh water and immerse the milk pipe in the water.
T Empty the other receptacle and place it under the frother
once more.
n T Touch the Steam symbol.
STEAM, the frother and milk pipe are rinsed with fresh
water.
. T Touch the Start symbol as soon as the receptacle containing
the water is empty.
The operation stops and your IMPRESSA is once more ready
for use.
50
6 Maintenance
Dismantling
and rinsing the
Professional
Cappuccino Frother
T Carefully remove the frother from the Connector System©
by twisting slightly.
T Dismantle the frother completely.
T Rinse all frother parts thoroughly under running water.
T Re-assemble the frother.
E Ensure that all individual parts are correctly and firmly connected to ensure correct operation of the frother
T Firmly attach the frother to the Connector System©.
Dismantling and
rinsing the Easy
Cappuccino Frother
T Carefully remove the frother from the Connector System©
by twisting slightly.
T Dismantle the frother completely.
T Rinse all frother parts thoroughly under running water.
T Re-assemble the frother.
E Ensure that all individual parts are correctly and firmly connected to ensure correct operation of the frother.
T Firmly attach the frother to the Connector System©.
Cleaning the
bean container
WARNING
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container. These residues may negatively affect
the coffee results. For this reason clean the bean container from
time to time.
Danger of injury to the fingers when the grinder is running.
T Switch the machine off with the on/off button Q before performing any work on the grinder.
T Switch the machine off at the power switch 3 .
T Open the bean container cover and remove the aroma preservation cover.
51
6 Maintenance
T Loosen the screw in the bean container and lift up the finger
protection.
T Remove the remaining beans with a vacuum cleaner.
T Clean the bean container with a soft, dry cloth.
T Put the finger protection down again and screw it back
tightly in place.
T Fill the bean container with coffee beans.
T Close the aroma preservation cover and the bean container
cover.
Descaling
the water tank
Limescale deposits may form in the water tank. To ensure correct
function of the machine, descale the water tank from time to time.
T Remove the water tank.
T If you use a CLARIS Blue filter cartridge, remove this.
T Descale the tank with a mild conventional descaling agent
in accordance with the manufacturer’s instructions.
T Rinse out the water tank thoroughly.
T If you use a CLARIS Blue filter cartridge, insert this again.
T Fill the water tank with fresh, cold water and reinsert the
tank.
52
7 Display messages
7 Display messages
Message
Cause/Result
Action
FILL WATER
TANK
The water tank is empty.
You cannot prepare any speciality
coffee or hot water or steam.
T Fill the water tank (See Chapter 2,
‘Preparing and using for the
first time – Filling the water tank’).
EMPTY
GROUNDS
The coffee grounds container is full.
You cannot prepare any speciality
coffees, but you can prepare hot
water or steam.
T Empty the coffee grounds
container and the drip tray.
EMPTY TRAY
The drip tray is full. You cannot
prepare any speciality coffees or hot
water or steam.
T Empty the drip tray.
TRAY
MISSING
The drip tray is not inserted correctly
or is not inserted at all. You cannot
prepare any speciality coffees or hot
water or steam.
T Insert the drip tray.
FILL BEANS
The bean container is empty. You
cannot prepare any speciality coffees
with beans. You can prepare preground coffee, hot water and steam.
T Fill the bean container (See
Chapter 2, ‘Preparing and using
for the first time – Filling the bean
container’).
READY / CLEAN
After 200 preparations or 80 switchon rinses, the IMPRESSA will prompt
you to clean it.
T Clean the machine (See
Chapter 6, ‘Maintenance –
Cleaning the machine’).
READY /
DE-SCALE
The IMPRESSA is prompting you to
descale it.
T Descale the machine (See
Chapter 6, ‘Maintenance –
Descaling the machine’).
READY /
FILTER
After 50 litres of water have flowed
through the filter cartridge, it will
cease to work.
T Replace the CLARIS Blue filter
cartridge (see Chapter 6 ‘Maintenance – Changing the filter’).
53
7 Display messages
Message
Cause/Result
Action
NOT ENOUGH
PRE-GROUND
There is too little pre-ground coffee
in the machine; the IMPRESSA stops
the operation.
T The next time you prepare coffee
use more pre-ground coffee (see
Chapter 4 ‘Preparation at the touch
of a button – Pre-ground coffee’).
TOO HOT
The system is too hot to start a
maintenance programme.
T Prepare a speciality coffee or hot
water.
54
8 Troubleshooting
8 Troubleshooting
Problem
Cause/Result
Action
Insufficient foam is produced when the milk is
frothed or milk sprays from
the cappuccino frother.
The cappuccino frother
is dirty.
T Rinse and clean the cappuccino
frother(see Chapter 6,
T ‘Maintenance – Cappuccino
frother’).
Coffee only comes out in
drips when it is being
prepared.
Coffee or pre-ground
coffee has been ground
too finely and is blocking
the system.
T Put the grinder on a coarser setting
or use coarser pre-ground coffee (refer
to Chapter 2, ‘Preparing and using for
the first time – Adjusting the grinder’).
Water hardness cannot be
adjusted.
The CLARIS Blue filter
cartridge is activated.
T Deactivate the filter cartridge in
programming mode.
FILL BEANS is displayed The grinder is not yet
although the bean container
has been filled.
T Prepare a speciality coffee.
completely filled with
beans.
FILL BEANS
The bean monitor
is dirty.
is not displayed although
the bean container is empty.
Clean the bean container (see
Chapter 6, ‘Maintenance – Cleaning
the bean container’).
EMPTY TRAY
The metal contacts of the Clean and dry the metal contacts on
drip tray are dirty or wet. the back of the drip tray.
is always displayed.
FILL WATER TANK
is displayed although the
water tank is full.
Grinder is making a very
loud noise.
The water tank float is
trapped.
T Descale the water tank (see
Chapter 6, ‘Maintenance – Descaling
the water tank’).
There are foreign objects
in the grinder.
T Contact Customer Support in your
country (see Chapter ‘JURA contact
details / Legal information’).
55
8 Troubleshooting
Problem
Cause/Result
Action
Little or no water or steam
comes out of the frother.
The pump is very quiet.
The Connector System
may be blocked by milk
residues or descaling
fragments loosened
during descaling.
T Remove the frother from the
Connector System©.
T Unscrew the black connector with
the aid of the hexagonal hole on the
measuring spoon for pre-ground
coffee.
T Clean the connector thoroughly.
T Manually screw the connector back
on to the Connector System©.
T Carefully tighten it using the
hexagonal hole on the measuring
spoon, turning by no more than a
quarter of a rotation.
ERROR 2
If the machine was
exposed to the cold for
a long period of time,
heating is disabled for
safety reasons.
T Warm the machine at room
temperature.
is displayed.
Other ERROR
messages are displayed.
©
–
T Turn the IMPRESSA off at the power
switch. Contact Customer Support in
your country (see Chapter ‘JURA
contact details / Legal information’).
E If you were unable to solve the problem, contact Customer
Support in your country (see Chapter ‘JURA contact details /
Legal information’).
56
9 Transport and environmentally neutral disposal
9 Transport and environmentally neutral disposal
Transport / Emptying
the system
Keep the packaging for your IMPRESSA. It should be used to protect
the machine during transport.
In order to protect the IMPRESSA from frost during transport, the
system must be emptied.
Precondition: READY is displayed.
T Carefully pull the cappuccino frother off the Connector
System©.
T Place a receptacle under the Connector System©.
n T Touch the Steam symbol.
HEATING
As soon as the machine has heated up, READY appears.
n T Touch the Steam symbol again.
STEAM, hot steam is discharged from the Connector
System©.
T Remove and empty the water tank.
Steam will continue to be discharged from the Connector
System© until the system is empty.
PRESS RINSE
Q T Press the on/off button.
The IMPRESSA is switched off.
E The next time you use the machine the system must
be refilled (see Chapter 2, ‘Preparing and using for the first
time – First-time use’).
Disposal
Please dispose of old machines in an environmentally neutral way.
H
Old machines contain valuable materials capable of being recycled
which should be salvaged for recycling. Please therefore dispose of
old machines via suitable collection systems.
57
10 Technical data
10 Technical data
Voltage
AS
220 –240 V ~, 50 Hz
F
120 V ~, 60 Hz
D
220 –240 V ~, 50 Hz
G
220 V ~, 50 Hz
Power
1450 W
Safety test
SDFG
Power consumption
12 Wh
ENERGY SAVE Power consumption
7 Wh
ENERGY SAVE w.
58
Pump pressure
Static max. 15 bar
Holding capacity of water tank
2,1 l
Holding capacity
of bean container
250 g
Holding capacity of coffee
grounds container
Approx. 16 servings
Cable length
Approx. 1,1 m
Weight
10,75 kg
Dimensions (W x H x D)
28,5 x 34,2 x 43,3 cm
Index
D
Descaling
A
Machine 46
Water tank 52
Amount
Display
Changing the amount of water during
preparation 25
Entering a permanent setting for the
amount of water for the cup size 26
Messages 53
Display messages 53
Disposal 57
Drip tray 8
Amount of coffee
Changing the amount of water during
preparation 25
Entering a permanent setting for the
amount of water for the cup size 26
E
Easy Cappuccino Frother
Dismantling and rinsing 51
Emptying the system 57
Energy Save Mode 36
Energy saving mode 14
Environmentally neutral disposal 57
Errors
Amount of water
Changing during preparation 25
Setting the water for the cup size 26
Automatic switch-off 37
B
Troubleshooting 55
Bean container 8
Cleaning 51
Filling 17
Espresso 29
F
Factory settings
Bus bar
Restore factory settings 38
Technical data 58
Filling
C
Bean container 17
Water tank 16
Cappuccino 30
Cappuccino frother
Filter
Cleaning 49
Easy Cappuccino Frother 9
Professional Cappuccino Frother 9
Rinsing 48
Changing 43
Inserting and activating 18, 19
First-time use 17
Frother
CLARIS Blue (filter cartridge)
Cleaning the cappuccino frother 49
Easy Cappuccino Frother 9, 15
Professional Cappuccino Frother 9, 15
Rinsing the cappuccino frother 48
Changing 43
Inserting and activating 18, 19
Cleaning
Bean container 51
Machine 45
Coffee 29
coffee
Pre-ground coffee 31
Coffee grounds container 8
Coffee strength
Changing before preparation 25
Connector System© 15
Control options 23
G
Grinder adjustment switch
Adjusting the grinder 20
H
Hot milk
Foaming and heating with the Professional
Cappuccino Frother 32
Hot water 34
Hot water nozzle 9
59
Hot water 34
Pre-ground coffee 31
Ristretto 29
I
Inserting
Water tank 16
Problems
Internet 15
Troubleshooting 55
K
Professional Cappuccino Frother 15
Knowledge Builder 15
Dismantling and rinsing 51
Programming mode 35
L
Automatic switch-off 37
Language 41
Permanent settings in programming
mode 26
Products 35
Reset settings to factory settings 38
Language 41
M
Machine
Cleaning 45
Descaling 46
Rinsing 42
Setting up 16
Switching off (Standby) 22
Switching on 21
R
Rinsing
Machine 42
Ristretto 29
Maintenance
Maintenance button 9
Maintenance tips 42
S
Safety information 10
Settings
Milk
Foaming and heating with the Professional
Cappuccino Frother 32
Foaming with the Easy Cappuccino
Frother 33
Entering a permanent setting for the
amount of water for the cup size 26
One-off settings before and during
preparation 24
Permanent settings in programming
mode 35
Milk foam
With the Easy Cappuccino Frother 33
With the Professional Cappuccino
Frother 32
Setting up 16
Supplied as standard 16
Switching off 22
Switching on 21
N
Nozzle
Hot water nozzle 9
T
Technical data 58
Transport 57
Troubleshooting 55
O
One-off settings before and during
preparation 24
V
P
Permanent settings in programming
mode 35
Pre-ground coffee 31
Pre-ground coffee 31
Preparation
At the touch of a button 29
Cappuccino 30
Coffee 29
Espresso 29
60
Viewing information and maintenance
status 39
Viewing maintenance status 39
W
Water tank 8
Descaling 52
Filling 16
61
62
63
Art. 68817/J7/en/200908
JURA contact details / Legal information
JURA Elektroapparate AG
Kaffeeweltstrasse 10
CH-4626 Niederbuchsiten
Tel.: +41 62 38 98 233
@ Further contact information is available on the company
website at www.jura.com.
Directives
The machine complies with the following EU directives:
Z 2006/95/EG – Low Voltage Directive
Z 2004/108/EG – Electromagnetic Compatibility
Z 2005/32/EG – Energy Directive
Technical changes
We reserve the right to make technical changes.
The illustrations used in the IMPRESSA J7 Manual show the
IMPRESSA J7 Piano Black. Your IMPRESSA could incorporate minor
changes.
Feedback
Your opinion is important to us!
Use the contact link at www.jura.com.
Copyright
The Instructions for Use contain information which is protected by
copyright. It is not permitted to photocopy or translate these
Instructions for Use into another language without the express
written consent of JURA Elektroapparate AG.
64