Kenwood Electronics RV-7000 AV receiver

AUDIO-VIDEO CONTROL CENTER
RV-7000
RV-6000
RA-5000
INSTRUCTION MANUAL
Declaration of Conformity with regard to
the EMC Directive 2004/108/EC
Manufacturer:
Kenwood Corporation
2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan
EU Representative's:
Kenwood Electronics Europe BV
Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands
RV-7000
RV-6000
RA-5000
© B60-5827-08/00 (E/X)
B60-5827-08_00_En.indd 1
10.8.3 11:07:33 AM
Safety precautions
¤ Caution : Read this page carefully to ensure safe
operation.
Unpacking
Unpack the unit carefully and make sure that all the accessories
are present.
Before use
Units are designed for operation as follows.
Australia ......................................................................................AC 240 V only
Europe .........................................................................................AC 230 V only
WARNING :
TO PREVENT FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
FM indoor antenna (1)
AM loop antenna (1)
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Remote control unit (1) RC-R0734
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Batteries* (R03) (2)
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF UNINSULATED
"DANGEROUS VOLTAGE" WITHIN THE PRODUCT’S
ENCLOSURE THAT MAY BE OF SUFFICIENT
MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC
SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL
TRIANGLE IS INTENDED TO ALERT THE USER TO
THE PRESENCE OF IMPORTANT OPERATING AND
MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.
* Batteries are attached to
the packing material.
If any accessories are missing, or if the unit is damaged or fails to
operate, notify your dealer immediately. If the unit was shipped
to you directly, notify your shipper immediately. Kenwood
recommends that you retain the original carton and packing
materials in case you need to move or ship the unit in the future.
Keep this manual handy for future reference.
Information on Disposal of Old Electrical and
Electronic Equipment and Batteries (applicable
for EU countries that have adopted separate
waste collection systems)
Products and batteries with the symbol (crossedout wheeled bin) cannot be disposed as
household waste.
Old electrical and electronic equipment
and batteries should be recycled at a facility
capable of handling these items and their waste
byproducts.
Contact your local authority for details in locating
a recycle facility nearest to you.
Proper recycling and waste disposal will help
conserve resources whilst preventing detrimental
effects on our health and the environment.
Notice: The sign "Pb" below the symbol for
batteries indicates that this battery
contains lead.
Maintenance of the unit
When the front panel or case becomes dirty, wipe with a soft,
dry cloth. Do not use thinner, benzine, alcohol, etc. for these
agents may cause discoloration.
In regard to contact cleaner
Do not use contact cleaners because it could cause a
malfunction. Be specially careful not to use contact cleaners
containing oil, for they may deform the plastic component.
2
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 2
10.8.3 11:07:33 AM
IMPORTANT SAFETY INSTRUCTIONS
¤ Caution : Read this page carefully to ensure safe operation.
10. Overloading
– All the safety and operating instructions should be read before the
product is operated.
– Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric
shock.
Keep These Instructions
– The safety and operating instructions should be retained for future
reference.
Heed All Warnings
– All warnings on the product and in the operating instructions
should be adhered to.
Follow All Instructions
– All operating and use instructions should be followed.
1. Clean only with dry cloth
– Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
2. Attachments
– Only use attachments/accessories specified by the manufacturer.
3. Do not use this apparatus near water
– This product shall not be exposed to dripping and splashing – for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in
a wet basement; or near a swimming pool; and the like. Do not place
an object containing liquid, such as a flower vase, on the appliance.
4. Accessories
– Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
5. Ventilation
– Slots and openings in the cabinet are provided for ventilation
and to ensure reliable operation of the product and to protect it
from overheating. Do not block any ventilation openings. Install
in accordance with the manufacturer’s instructions. The openings
should never be blocked by placing the product on a bed, sofa, rug,
or other similar surface. This product should not be placed in a builtin installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been adhered to.
6. Power Sources
– This product should be operated only from the type of power source
indicated on the product. If you are not sure of the type of power supply
to your home, consult your product dealer or local power company.
7.
CAUTION – Polarization
– Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
11. Object and Liquid Entry
– Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind
on the product.
Before use
Read These Instructions
12. Servicing
– Do not attempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
13. Damage Requiring Service
– Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
14. Replacement Parts
– When replacement parts are required, be sure the service technician
has used replacement parts specified by the manufacturer or have the
same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, or other hazards.
15. Safety Check
– Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in proper operating condition.
16. Wall or Ceiling Mounting
– This product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
17. Heat
– Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not place a flaming object, such as a candle or lantern, or near
the product.
18. Power Lines
– An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where
it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be fatal.
Notes:
Item 7 is not required except for grounded or polarized equipment.
8. Power Cord Protection
– Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus
9. Lightning
– Unplug this apparatus during lightning storms or when unused
for long periods of time.
English
B60-5827-08_00_En.indd 3
3
10.8.3 11:07:34 AM
Contents
¤To ensure safety, read the items carrying this marking
carefully.
Before use
Before use
¤Safety precautions ........................................... 2
Unpacking ............................................................. 2
¤IMPORTANT SAFETY INSTRUCTIONS .............. 3
Contents ................................................................. 4
Special Features .................................................... 6
How to read this manual....................................... 8
Names and functions of parts .............................. 9
Connections
Notes on connections ......................................... 14
Speaker placement ............................................. 15
Connecting speakers .......................................... 16
Connecting components equipped with HDMI
terminals .......................................................... 20
Connecting a TV Monitor.................................... 21
Connecting a CD player ...................................... 22
Connecting a DVD player ................................... 23
Connecting a video player.................................. 24
Connecting an audio player ............................... 25
Connecting to the [AV AUX] jacks ...................... 25
Connecting antennas.......................................... 26
Turning this unit ON............................................ 27
Setup
Speaker setup (Easy Setup)
(RV-7000/RV-6000 only).................................. 28
Speaker setup (Detailed Setup) ......................... 29
Speaker setup flow
Speaker configuration
Speaker Level
Speaker Distance
Crossover
LFE (Low Frequency Effect) Level
Lip Sync
APS (Auto Power Save)
HDMI setup flow
Audio Out
HDMI setup .......................................................... 33
Lip Sync
HDMI Link
Power Control
Confirming the HDMI function .......................... 35
Before operation
Confirming the basic HDMI operations
Confirming the HDMI control functions
Playing music or movie
Preparation for playing music or movie ............ 36
Turning on the power
Setting the speaker system
Selecting the input mode
ARC (Audio Return Channel)
Playback............................................................... 37
Monitoring the input source in the original sound
(STRAIGHT DECODE mode)(RV-7000/RV-6000
only)
Listening to music with PURE AUDIO MODE . 38
Surround effects
Listen mode ......................................................... 39
Surround play using the listen mode ................ 41
Checking the current input signal ..................... 42
Listening to radio broadcasts
Tuning into a radio station ................................. 43
Using Radio Data System.................................... 44
Auto Memory....................................................... 44
Presetting radio stations manually ................... 45
Receiving preset stations ................................... 45
Tuning by program type (PTY search) ............... 46
Receiving preset stations in order (P.CALL) ...... 46
Using the DISPLAY key........................................ 47
Sound adjustment
Adjusting the sound ........................................... 48
ACTIVE EQ mode
Bass Boost
Adjusting the Tone
Adjustments according to the playing source .. 49
Speaker level adjustment
Input level adjustment
Midnight mode
Panorama mode (RV-7000/RV-6000 only)
Dimension (RV-7000/RV-6000 only)
Center width (RV-7000/RV-6000 only)
Center image (RV-7000/RV-6000 only)
Convenient functions
Convenient functions ......................................... 52
Display dimmer adjustment
Listening with headphones
Muting the sound
Remote control operations for Kenwood BD/DVD
players .............................................................. 53
Troubleshooting
Troubleshooting.................................................. 54
Resetting the unit
Glossary ............................................................... 57
Specifications ...................................................... 58
4
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 4
10.8.3 11:07:35 AM
Before use
English
B60-5827-08_00_En.indd 5
5
10.8.3 11:07:35 AM
Special Features
\ HDMI™(High-Definition Multimedia Interface) repeater function
Before use
Compatibility with the HDMI interface can transfer HDTV video and latest high-quality audio. It makes possible entertainment of
high-quality video including 3D video as well as high-quality audio.
\ High-quality music playback in Pure Audio Mode
This function reproduces music signals in high quality with high fidelity to original sound.
In this mode, the display and the analog video circuitry are turned off to eliminate their effects on the audio circuitry. In addition, the
optimum listen mode is selected according to the input music signal.
\ True home theater sound
This unit incorporates a wide variety of surround modes to bring you maximum enjoyment from your video software. Select a
surround mode according to your equipment or the software you are going to play and enjoy!
RV-7000
RV-6000
RA-5000
Terminal
Input Signal
HDMI
Dolby TrueHD
✔
Dolby Digital Plus
✔
DTS-HD Master Audio
DTS-HD High
Resolution Audio
PCM (Multi Channel)
✔
✔
✔
DSD
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
DTS
✔
✔
✔
PCM (2 Channel)
✔
✔
✔
Analog
✔
✔
✔
RV-7000
RV-6000
RA-5000
DIGITAL IN
Dolby Digital EX
(OPTICAL/COAXIAL)
Dolby Digital
DTS-ES (Discrete,
Matrix)
DTS 96/24
AUDIO IN
Listen mode
✔
Dolby Pro Logic IIz (Height)
✔
Dolby Pro Logic IIx (Movie, Music, Game)
✔
✔
Dolby Pro Logic II (Movie, Music, Game)
✔
✔
Dolby EX
✔
Dolby Pro Logic
✔
✔
DTS Neo:6 (Cinema, Music)
✔
✔
DTS Neo:6
✔
✔
Stereo
✔
✔
Virtual Surround
✔
✔
Dolby Virtual Speaker
✔
✔
✔
✔
\ Easy Setup of the speaker (RV-7000/RV-6000)
The speaker settings can be completed by simply selecting the room type and the listening position. The audio will be corrected
automatically according to the characteristics of the speaker system in use.
6
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 6
10.8.3 11:07:35 AM
\ Crossover Frequency Adjustment
The bass frequency from the subwoofer and the other speakers can be adjusted making better sound phase between speakers and
natural sound field.
This function corrects deviation between the video and audio. Automatic correction is also available provided that all of the playback
component, this unit and the TV are connected through HDMI.
Before use
\ Lip Sync function
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872;
7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide
patents issued & pending. DTS and the Symbol are registered
trademarks, & DTS-HD, DTS-HD Master Audio, and the DTS logos
are trademarks of DTS, Inc. Product includes software. © DTS, Inc.
All Rights Reserved.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,003,467;
7,212,872 & other U.S. and worldwide patents issued & pending.
DTS, the Symbol, ES, and Neo:6 are registered trademarks & DTS
Digital Surround, DTS 96/24 and the DTS logos are trademarks of
DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks of
Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing, LLC.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS and the Symbol
are registered trademarks & DTS Digital Surround, the DTS 96/24
and the DTS logos are trademarks of DTS, Inc. Product includes
software. © DTS, Inc. All Rights Reserved.
English
B60-5827-08_00_En.indd 7
7
10.8.3 11:07:35 AM
How to read this manual
Before use
The operating instructions given in this manual assume that the user mainly operates the receiver using the remote control unit. When the
same operation is also available on the main unit, the operating method is indicated in illustrations.
The [VOLUME CONTROL] knob on the main unit are operated by turning the knobs clockwise or counterclockwise.
This icon indicates that the function can be operated (or
recommended to operate) only with the unit displayed with the icon.
: main unit
Speaker setup
(Detailed Setup)
: remote control unit
Playback
The detailed settings allow you to enjoy full performance of
the receiver according to the environment of your listening
room.
The knob on the main unit
is pointed with an arrow to
indicate that it can be turned
in either direction.
92/80(&21752/
For creating the best listening environment, Kenwood
recommends to perform the setup at the listening position.
,13876(/(&725/
6(783
08/7,&21752/
Speaker setup flow
Speaker settings consist of 7 elements.
1 Enter the Detailed Setup mode.
The keys and controls used in
the operations described in each
section are indicated with their
names.
The descriptions of the functions
available only on the remote
control unit are accompanied only
with the illustration of the remote
control unit. The descriptions of
the functions available only on the
main unit are accompanied only
with the illustration of the main
unit.
[SETUP]
Use
e [MULTI CONTROL O/] to
t select an item to set.
The names of the operated keys
or knobs are enclosed inside
brackets.
[SETUP]
Elements
Display
Setting
Speaker Configuration
"SP SETUP"
Selects whether each speaker channel is
used or, if used, its size.
Speaker Level
"TESTTONE"
Selects the output level from each
speaker.
Speaker Distance
"DISTANCE"
Selects the distance between each
speaker and the listening position.
"CROSSOVER"
Sets the lower limit of the bass
frequencies reproduced from the speakerss
set to "NML" in the "SP SETUP". The
frequencies below the frequency set here
are distributed to other speakers (those
set to "LRG" and the subwoofer).
Crossover
When a key is used to select
an option, the list of options is
shown in the form of a table.
This icon indicates supplementary
information, restrictions in
operation or tips on operation.
92/80( Input source keys
1 Select a source.
Use the Input source keys on the remote control unit
to select a source.
Or use [INPUT SELECTOR] key on the main unit.
Example: Display when HDMI 1 input source is
selected
2 Start playback from the selected source.
3 Usee [VOLUME /o]] to adjust the volume.
4 Enjoy various surround effects.
You can enjoy a variety of listen modes. (See
<Surround play using the listen mode> G.)
The surround effects can be fine tuned according
to the selected input source. (See <Adjustments
according to the playing source> E.)
t If the input signal uses a number of channels larger
than the number of speakers in use, the signals are
distributed automatically according to the available
speakers.
2 Set each item.
See the followings for each setup item.
Continued
This icon indicates that the
description continues on the
next page.
• In this manual, RV-7000 is used for the illustrations of front panel and rear panel.
• The illustrations of the main unit display panel and the examples of operations are shown for the purpose of explanation and may
differ from the actual view or operation.
8
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 8
10.8.3 11:07:35 AM
Names and functions of parts
Main unit
Before use
5$
1
(Power) key
Standby indicator
Press to switch this unit ON or to put it
to standby.
The standby indicator lights in the
standby mode.
2 Display
3 DOLBY VIRTUAL SPEAKER
5$
# Illumination
$ MULTI CONTROL ∞/5 key
* PURE AUDIO MODE key
TUNING key
Press to select a radio station.
EASY SETUP key
•
Use for Easy Setup of the speakers.
indicator (RA-5000 only)
4 Remote sensor
5 VOLUME CONTROL knob
6 PHONES jack
RA-5000:
TONE key
i
Press to adjust the tone.
^ RV-7000/RV-6000:
Use for headphone listening.
LISTEN MODE key
7 SPEAKERS ON/OFF key
fl
Press to turn the speakers ON/OFF.
8 INPUT SELECTOR ∞/5 key
Press to select the input source.
9 BAND key
e
0 AUTO/MONO key
e
Press to select the broadcasting band.
Press to switch the radio tuning mode
between auto tuning and manual
tuning.
! INPUT MODE key
fl
@ SETUP key
ª
Press to select the input mode.
q
Press to select the listen mode.
RA-5000:
DIMMER key
°
Press to switch the STRAIGHT DECODE
MODE/PURE AUDIO MODE ON/OFF.
(RV-7000/RV-6000)
Press to switch the PURE AUDIO
MODE ON/OFF. (RA-5000)
Press to select a setting item.
% RV-7000/RV-6000:
5$
W
( AV AUX jacks
Connect a video camera, videogame
machine, etc.
Standby mode
While the standby indicator is lit, a small
amount of power is supplied to the system
to back up the memory. This is called
standby mode. Under the condition, the
system can be turned ON by the remote
control unit.
Press to switch the brightness of the
display and indicators.
& RV-7000/RV-6000:
VIRTUAL SURROUND key w
Press to switch the Virtual Surround
function ON/OFF.
RA-5000:
DOLBY VIRTUAL SPEAKER key
w
Press to switch the Dolby Virtual
Speaker function ON/OFF.
Press to set up this unit.
English
B60-5827-08_00_En.indd 9
9
10.8.3 11:07:38 AM
Names and functions of parts
Remote control unit
1 AUTO MEMORY key
r
Before use
Use for auto memory of FM radio stations.
AUDIO key
!
1
2
3
4
@
#
$
Use to operate the Kenwood BD/DVD player.*
2 MEMORY key
t
Press to preset radio stations in memory.
POP UP key
Use to operate the Kenwood BD/DVD player.*
3 SUBTITLE key
Use to operate the Kenwood BD/DVD player.*
%
5
^
&
*
(
6
7
8
9
0
PTY key
y
Press to search a radio station by program type.
4 DISPLAY key
Press to display the type of surround format.
w
Press to display Radio Data System information.
u
5 Numeric keys
Use to recall a preset radio station. t
Use to operate the Kenwood BD/DVD player.*
6 LISTEN MODE keys
q
7 PURE AUDIO MODE key
°
Press to switch the listen mode.
)
(17(5
087(
Press to switch the STRAIGHT DECODE MODE/PURE AUDIO
MODE function ON/OFF. (RV-7000/RV-6000)
Press to switch the PURE AUDIO MODE function ON/OFF.
(RA-5000)
8 %/fi/@/# keys
ENTER key
HOME/TOP MENU key
DISC MENU/MENU key
RETURN key
ON SCREEN key
¡
™
Use to operate the Kenwood BD/DVD player.*
9 8 key
Use to operate the Kenwood BD/DVD player.*
BAND key
e
Press to select the broadcasting band.
6 key
£
Use to operate the Kenwood BD/DVD player.*
AUTO/MONO key
e
Press to switch the radio tuning mode between auto tuning
and manual tuning.
¢
7 key
Use to operate the Kenwood BD/DVD player.*
0 P.CALL 4/¢ keys
Press to recall a preset radio station.
y
Use to operate the Kenwood BD/DVD player.*
!
RECEIVER key
Use to turn this unit on and off.
BD/DVD key
E
Press to switch the Kenwood BD/DVD player ON/OFF.
10
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 10
10.8.3 11:07:39 AM
@ ACTIVE EQ key
i
# VIRTUAL key
w
$ BASS BOOST key
i
Press to switch the ACTIVE EQ function ON/OFF.
Before use
Press to switch the Virtual Surround function ON/OFF.
(RV-7000/RV-6000)
Press to switch the Dolby Virtual Speaker function ON/OFF.
(RA-5000)
Press to enhance bass sound.
% TONE key
i
^ SOUND key
o
& SETUP key
ª
* HDMI SETUP key
‹
Press to adjust the tone.
Press to adjust sound quality and acoustic field.
Press to set up this unit.
Use for HDMI Setup.
( MULTI CONTROL ∞/5 keys
Press to select a setting item.
) VOLUME %/fi keys
¡ MUTE key
W
Press to mute the sound temporarily.
™ TUNING 1/¡ keys
Press to select a radio station. e
Use to operate the Kenwood BD/DVD player.*
£ Input source keys
Press to select the input source.
¢ DIMMER key
W
Press to switch the brightness of the display and indicators.
• * For how to be able to use the keys to operate the
Kenwood BD/DVD player, see <Remote control
operations for Kenwood BD/DVD players>. E
English
B60-5827-08_00_En.indd 11
11
10.8.3 11:07:40 AM
Names and functions of parts
Remote control unit
Before use
Operation
Operate the remote control unit by pointing it to the remote
sensor of this unit.
When this unit is in standby mode (which is indicated by lighting
of the standby indicator), pressing the [ RECEIVER] key turns
this unit ON. Pressing the [ RECEIVER] key again turns this unit
OFF (standby mode).
When operating the connected components, always press
the input source key of the component you need to operate
first to swith the remote control unit to the selected input
source mode, and then press the keys of the corresponding
operation.
• The supplied batteries may have shorter lives than
ordinary batteries due to use during operation checks.
• When the remote-controllable distance gets shorter than
before, replace both batteries with new ones.
¤CAUTION
Do not leave the battery near fire or under direct sunlight.
A fire, explosion or excessive heat generation may result.
Operating range (Approx.)
Standby indicator
Remote sensor
Loading batteries
1 Remove the cover.
2 Insert batteries.
Insert two (R03) batteries following the polarity indications.
3 Close the cover.
12
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 12
10.8.3 11:07:40 AM
Display
Before use
Virtual Surround
Lights up when the
Virtual Surround is on.
SP (speaker)
Lights up when the
speakers are on.
CLIP
Lights up when the input level is
too high.
MUTE
Blinks when muting
is on.
PTY
Lights up when searching a radio
station by program type.
RDS
Lights up when receiving an
Radio Data System station.
AUTO
Lights up when the tuning
mode is "AUTO".
AUTO DETECT
Band indicators
Lights up when the input
mode is set to "AUTO".
Lights up the selected
broadcast band
indicator.
Character display
Listen mode/Input signal
format indicators
HDMI
ST.
Lights up when the
components connected
with HDMI are
recognized.
Lights up when stereo
broadcasting is tuned.
TUNED
Lights up when a radio
station is tuned.
TONE
Lights up when the
tone setting is on.
STRAIGHT
Lights up when the Straight
Decode Mode is on.
STEREO
Lights up when the
Listen mode is Stereo.
ACTIVE EQ
Lights up when the
Active EQ is on.
English
B60-5827-08_00_En.indd 13
13
10.8.3 11:07:42 AM
Notes on connections
¤CAUTION
Speaker placement
RV-7000 (Surround Back speaker)
Do not connect the power cord to a wall outlet until all
connections are completed.
Front speaker
Front speaker
Connections
When connecting the related system components, be sure to
refer to the instruction manuals supplied with the components
you are connecting.
• Be sure to remove the power cord from the AC outlet
before plugging or unplugging any connection cords.
Plugging/unplugging connection cords without
disconnecting the power cord can cause malfunctions
and may damage the unit.
• Be sure to insert all connection cords securely. If their
connections are imperfect, the sound and video may not
be produced or there will be noise interference.
• If this unit is installed in the proximity of a source of
magnetism such as a magnet, color irregularities due to
interference with the speakers may be observed on the
TV monitor screen. Be careful in the installation.
Center speaker
Subwoofer
Listening
position
Surround speaker
Surround speaker
Surround Back speaker
Microcomputer malfunction
RV-7000 (Front Height speaker)
If operation is not possible or an erroneous display appears,
even though all connections have been made properly, reset the
microcomputer by referring to <Resetting the microcomputer>.
T
Front Height speaker
Front speaker
Subwoofer
Front speaker
Center speaker
Listening
position
Surround speaker
Surround speaker
¤CAUTION
The power of this equipment will not be completely cut off
from the wall outlet when the power switch is turned off.
Install the equipment so that the wall outlet is easily
accessible and, in case of emergency, immediately unplug the
power cord from the wall outlet.
RV-6000
Front speaker
Front speaker
¤CAUTION
Be sure to adhere to the following, or proper ventilation
will be blocked causing damage or fire hazard.
• Do not install the unit on the rear, side or top panel.
• Do not cover the unit with a cloth or install the unit on a
carpet or mattress.
• Do not install the unit in a poorly ventilated place.
• Leave some space around the unit (from the largest outside
dimension including projection) equal to or greater than,
shown below.
Top panel : 50 cm
Side panel : 10 cm
Back panel : 10 cm
14
Subwoofer
Center speaker
Surround speaker
Listening
position
Surround speaker
Surround Back speaker
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 14
10.8.3 11:07:42 AM
RA-5000
Front speakers
Front speaker
Front speaker
Install in the front left and right positions. Symmetrical
installation is ideal. The front speakers are always used regardless
of the listen mode.
Front Height speakers
Install on the front of the listening position, at the same height as
the surround speakers.
Listening
position
Install in the front center position. This speaker improves
the acoustic image positioning and reproduction of sound
movement.
Surround speakers
Install straight on or slightly behind the left and right of the
listening position, at in an as high as possible height (ideally
one meter above the height of the listener’s ears). Symmetrical
installation is ideal. The surround speakers reproduce the feeling
of movement and presence of sound.
Connections
Center speaker
Subwoofer
Subwoofer
In general, install on the front center position near the front
speakers. The subwoofer reproduces the powerful bass effects. As
it is less directional to other speakers, it can be installed so that
the bass can be reproduced best according to the listening room
layout.
Surround Back speaker(s)
Install on the rear of the listening position, at the same height as
the surround speakers.
• Ideal surround play is possible when all of the speakers
above are installed. If the center speaker and/or the
subwoofer is not installed, the system optimizes playback
according to the current system by assigning the sound
of absent channels to other speakers.
• RV-6000 :
Up to two subwoofers can be connected to RV-6000
depending on speaker setup. See <Connecting
speakers> & for how to connect the subwoofers.
English
B60-5827-08_00_En.indd 15
15
10.8.3 11:07:44 AM
Connecting speakers
Connections
RV-7000
Power Amplifier
Powered
Subwoofer
Right
Left
Surround Back speaker/
Front Height speakers
Right
Left
Front speakers
Center speaker
Right
Left
Surround speakers
• Speaker impedance : 6 – 16Ω
• Never short circuit the + and – speaker cords.
• If the left and right speakers are connected inversely or the speaker cords are connected with reversed polarity, the sound will be
unnatural with ambiguous acoustic imaging. Be sure to connect the speakers correctly.
• RV-6000 :
Subwoofer sound comes out at the both Subwoofer terminals (SPEAKERS and PREOUT) simultaneously depending on speaker setup.
• RV-7000 :
When only one surround back speaker is used, connect it to the [SURROUND BACK L] terminal.
16
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 16
10.8.3 11:07:44 AM
RV-6000
Connections
Power Amplifier
Powered
Subwoofer
Surround Back
speaker
Subwoofer/
Surround Back
speaker
Right
Left
Front speakers
Center speaker
Right
Left
Surround speakers
English
B60-5827-08_00_En.indd 17
17
10.8.3 11:07:46 AM
Connecting speakers
Connections
RA-5000
Powered
Subwoofer
18
Right
Left
Front speakers
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 18
10.8.3 11:07:47 AM
How to connect the wire to terminals
(Screw type terminal)
How to connect the wire to terminals
(Push type terminal)
1 Strip the vinyl coating of the wire by a length of
1 Strip the vinyl coating of the wire by a length of
about 1 cm.
about 1 cm.
2 Push the lever.
3 Insert the wire.
3 Insert the wire.
Connections
2 Loosen the knob.
Insert until the metallic conductor becomes invisible.
Insert until the metallic conductor becomes invisible.
4 Release the lever.
4 Tighten the knob.
English
B60-5827-08_00_En.indd 19
19
10.8.3 11:07:48 AM
Connecting components equipped with HDMI terminals
The HDMI connection can transfer both the video and audio signals through a single HDMI cable. It makes possible entertainment of highquality video including 3D video as well as high-quality audio. The HDMI connection also enables interlocking of the power of the TV with
that of this unit. (See <HDMI setup> ‹.)
1 Using an HDMI cable, connect the HDMI input terminal ([HDMI 1], [HDMI 2], [HDMI 3] or [HDMI 4] terminal) of
this unit to the HDMI output terminal of a playback component such as a Blu-ray disc player.
2 Using another HDMI cable, connect the [HDMI MONITOR OUT] terminal of this unit to the HDMI input terminal
Connections
of the TV monitor.
HDMI MONITOR IN
HDMI OUT
Blu-ray Disc Player
HDMI OUT
TV Monitor
Digital Tuner and etc.
Using the HDMI function
The HDMI setup is required to use the HDMI function. See <HDMI
setup> ‹.
Flow of video signal
The digital video signal input from the HDMI input terminal is
output only at the HDMI monitor output terminal.
Flow of audio signal
The digital audio signal input from the HDMI input terminal
is output at the speakers connected to this unit. It can also be
output at the TV monitor connected to this unit according to the
HDMI setup. (See <HDMI setup> ‹.)
• An HDMI/DVI converter cable is necessary to connect a
TV monitor with a DVI input terminal. The TV monitor also
needs to be compatible with HDCP (High-bandwidth
Digital Contents Protection). Note that the video may be
unable to be monitored depending on the combined
components.
• When components are connected through the
HDMI connection, it takes a certain period before the
video/audio are output because they need mutual
authentication.
• If the video and/or audio are not output normally, turn all
of the connected components off then on, and try again.
• If the resolution of the incoming video signal is different
from that of the TV, no video is output. In this case, adjust
the resolution on the BD/DVD player.
• Use an certified High Speed HDMI™ cable (Category 2
cable) for connection.
To use the ARC function of this unit, be sure to use a cable
carrying the logo shown above.
20
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 20
10.8.3 11:07:49 AM
Connecting a TV Monitor
1 Connect A and B to the TV monitor according to the connected video component as shown below.
For the video and audio connections of the connected component, see the description on the page for the connected components.
• The HDMI video cannot be viewed unless the TV monitor is equipped with the HDMI terminal.
• The signal input at "DVD IN" or "VIDEO IN" are output exclusively from "MONITOR OUT" of "VIDEO".
Connections
B
A
HDMI
MONITOR IN
VIDEO IN
TV Monitor
English
B60-5827-08_00_En.indd 21
21
10.8.3 11:07:50 AM
Connecting a CD player
Connections
1 Connect the audio line: Connection B (digital) or A (analog).
B
A
AUDIO OUT
(Analog)
OPTICAL DIGITAL
OUT (AUDIO)
CD player
22
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 22
10.8.3 11:07:51 AM
Connecting a DVD player
1 Connect the audio line: Connection A (digital) or B (analog).
2 Connect the video line: Connection C.
3 Connect the TV monitor.
Connect as shown in <Connecting a TV Monitor> ¡.
Connections
B
A
AUDIO OUT
(Analog)
COAXIAL DIGITAL
OUT (AUDIO)
C
VIDEO OUT
DVD player
• When the connected DVD player and TV monitor have the HDMI terminals, it is recommended to use the HDMI connection. (See
<Connecting components equipped with HDMI terminals> ).)
English
B60-5827-08_00_En.indd 23
23
10.8.3 11:07:52 AM
Connecting a video player
1 Connect the audio line: Connection A (digital) or B (analog).
2 Connect the video line: Connection C.
3 Connect the TV monitor.
Connections
Connect as shown in <Connecting a TV Monitor> ¡.
B
A
OPTICAL DIGITAL
OUT (AUDIO)
AUDIO OUT
(Analog)
C
VIDEO OUT
DVD Recorder, etc.
• When the connected Video player and TV monitor have the HDMI terminals, it is recommended to use the HDMI connection. (See
<Connecting components equipped with HDMI terminals> ).)
24
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 24
10.8.3 11:07:53 AM
Connecting an audio player
Connections
AUDIO OUT
Cassette deck and etc.
Connecting to the [AV AUX] jacks
A component that is usually not connected to this unit, such as a portable video camera, can be connected to the [AV AUX] jacks on the
front panel of this unit.
VIDEO OUT AUDIO OUT
Portable video camera,
videogame machine and
etc.
English
B60-5827-08_00_En.indd 25
25
10.8.3 11:07:54 AM
Connecting antennas
Connections
The broadcast reception cannot be made unless the antennas are connected. Connect the antennas correctly as instructed below.
FM indoor antenna
Fix on a wall, etc. with a good
reception condition.
The provided antenna is intended
for temporary use in indoors. To
obtain stable FM reception, it is
recommended to use an outdoor
antenna. Be sure to disconnect the
indoor antenna when an outdoor
antenna is installed.
FM antenna adapter
(commercially available)
FM outdoor antenna
(commercially available)
AM loop antenna
Install in a position as apart as possible from this unit, the TV monitor,
personal computer, speaker cords and power cord, and place in an
orientation that can offer the best reception condition.
AM loop antenna
FM indoor antenna
1 Attach to the stand.
1 Insert the antenna cord.
Insert into the groove.
2 Push the lever.
2 Fix the antenna on the wall.
3 Insert the antenna cord.
Insert until the metallic
conductor becomes invisible.
4 Release the lever.
26
FM outdoor antenna
Lead the 75Ω coaxial cable connected to the FM outdoor antenna
into the room and connect it to the FM 75Ω terminal.
¤Caution for outdoor antenna installation
Since antenna installation necessitates skill and experience,
always consult your dealer before installation. The antenna
should be placed at a distance from the power distribution
wires. Otherwise, an electric shock accident may occur if the
antenna falls down.
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 26
10.8.3 11:07:56 AM
Turning this unit ON
Connections
5(&(,9(5
1 After completing all of the necessary connections, connect the power cord to a wall power outlet.
The standby indicator on the front panel lights red to indicate the standby mode.
2 Press the [
(Power)] key of this unit or the [
RECEIVER] key of the remote control unit to turn this unit ON.
The standby indicator on the front panel goes out and the display panel lights up.
To turn this unit OFF (standby mode)
Press the [
(Power)] key of this unit or the [
RECEIVER] key of the remote control unit.
English
B60-5827-08_00_En.indd 27
27
10.8.3 11:07:57 AM
Speaker setup (Easy Setup) (RV-7000/RV-6000 only)
The speaker settings can be completed by simply selecting the
room type and listening position. The audio will be corrected
automatically according to the characteristics of the speaker
system in use.
If more detailed speaker settings are required, use the procedure
in <Speaker setup (Detailed Setup)> ª.
• Easy setup with may not be appropriate with certain
speaker systems or listening environment. In this case, go
through <Speaker setup (Detailed Setup)>.
• Easy setup can set only the 5.1 channel system.
If the setup for 7.1-channel or 6.1-channel system is
required, go through <Speaker setup (Detailed Setup)>.
• Subwoofer Re-mix:
Mixes the bass tone of other channels to the subwoofer
channel.
Reference for listening room size
5m (16'5-3/8")
3m (9'10-3/8")
6m (19'8-7/8")
1 Press [EASY SETUP] to enter the Easy Setup mode.
2 Set the listening room size.
Use [MULTI CONTROL ∞/5] to select your room type.
12m2
SMALL
7m (23'3/8")
($6<6(783
08/7,&21752/∞/5
4m (13'1-7/8")
Setup
4m (13'1-7/8")
24m2
MEDIUM
35m2
LARGE
[EASY SETUP]
3 Select the listening position.
Use [MULTI CONTROL ∞/5] to select your listening
position.
[EASY SETUP]
Reference for listening position
FRONT
CENTER
The unit exits the Easy Setup mode, and the speakers are
set up as shown below.
REAR
Setting of RV-7000
Subwoofer \ ON
Front speaker \ Avarage size
Center speaker \ Avarage size
Surround speaker \ Avarage size
Surround Back speaker \ OFF
Front Height speaker \ OFF
Subwoofer Re-mix \ ON
Setting of RV-6000
Subwoofer \ ON
Front speaker \ Avarage size
Center speaker \ Avarage size
Surround speaker \ Avarage size
Surround Back speaker \ OFF
Subwoofer Re-mix \ ON
For details on the setting contents, see <Speaker setup
(Detailed Setup)> ª.
28
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 28
10.8.3 11:07:58 AM
Speaker setup (Detailed Setup)
The detailed settings allow you to enjoy full performance of the
receiver according to the environment of your listening room.
For creating the best listening environment, Kenwood
recommends to perform the setup at the listening position.
Speaker configuration
Select the use of each speaker and its size.
1 Enter the Detailed Setup mode.
[SETUP]
Use [MULTI CONTROL ∞/5] to select "SP SETUP".
6(783
[SETUP]
2 Select the use and size of each speaker.
Use [MULTI CONTROL ∞/5] to select the speaker and its
use or size.
Speaker setup flow
[SETUP]
Speaker settings consist of 7 elements.
Repeat the above operations until all of the speakers
have been set up.
1 Enter the Detailed Setup mode.
Setup
08/7,&21752/
Settings of RV-7000
[SETUP]
Speaker
Use [MULTI CONTROL ∞/5] to select an item to set.
Subwoofer
Front speaker
[SETUP]
Elements
Display
Setting
Speaker Configuration
"SP SETUP"
Selects whether each speaker channel is
used or, if used, its size.
Speaker Level
Speaker Distance
Crossover
Low Frequency Effects
Level
"TESTTONE"
Selects the output level from each
speaker.
"DISTANCE"
Selects the distance between each
speaker and the listening position.
"CROSSOVER"
Sets the lower limit of the bass
frequencies reproduced from the speakers
set to "NML" in the "SP SETUP". The
frequencies below the frequency set here
are distributed to other speakers (those
set to "LRG" and the subwoofer).
"LFE LVL"
Selects the level of bass audio
enhancement.
Low Frequency Effect channel delivers
separate non-directional bass signals to
the subwoofer for more dynamic deep
bass sound effects.
Lip Sync
"LIP SYNC"
Adjusts the deviation in time between
the video and audio.
Auto Power Save
"APS"
Sets Auto Power Save ON/OFF.
"EXIT"
Exits the Detailed Setup mode.
2 Set each item.
Center speaker
Display
"SUBW ON"
Subwoofer is connected.
"SUBW OFF"
Subwoofer is not connected.
"FRNT LRG"
Large size front speaker
"FRNT NML"
Average size front speaker
"CNTR LRG"
Large size center speaker
"CNTR NML"
Average size center speaker
"CNTR OFF"
Center speaker is not connected.
"SURR LRG"
Large size surround speaker
Surround speaker "SURR NML"
Front Height/
Surround
Back speaker
connection
Front Height
speaker
Surround Back
speaker
Subwoofer
Re-mix*1
Setting
Average size surround speaker
"SURR OFF"
Surround speakers are not connected.
"FH/SB FH"
Front Height speaker is connected.
"FH/SB SB"
Surround Back speaker is connected.
"FH/SBOFF"
Front Height/Surround Back speaker is
not connected.
"FH LRG"
Large size front height speaker is
connected. (7.1ch)
"FH NML"
Average size front height speaker is
connected. (7.1ch)
"SB LRGX2"
Large size surround back speaker is
connected. (7.1ch)
"SB LRGX1"
Large size surround back speaker is
connected. (6.1ch)
"SB NMLX2"
Average size surround back speaker is
connected. (7.1ch)
"SB NMLX1"
Average size surround back speaker is
connected. (6.1ch)
"RMX ON"
Subwoofer re-mix is on.
"RMX OFF"
Subwoofer re-mix is off.
See the followings for each setup item.
Continued
English
B60-5827-08_00_En.indd 29
29
10.8.3 11:08:00 AM
Speaker setup (Detailed Setup)
Settings of RV-6000
Speaker
Display
Setting
Subwoofer/
Surround
Back speaker
connection
"SW/SB SW"
Subwoofer is connected.
Subwoofer
Setup
Front speaker
Center speaker
"SW/SB SB"
Surround Back speaker is connected.
"SW/SBOFF"
Subwoofer/Surround Back speaker is not
connected.
"SUBW ON"
Subwoofer is connected.
"SUBW OFF"
Subwoofer is not connected.
"FRNT LRG"
Large size front speaker
"FRNT NML"
Average size front speaker
"CNTR LRG"
Large size center speaker
"CNTR NML"
Average size center speaker
"CNTR OFF"
Center speaker is not connected.
"SURR LRG"
Large size surround speaker
Surround speaker "SURR NML"
Surround Back
speaker
Subwoofer
Re-mix*1
Average size surround speaker
"SURR OFF"
Surround speakers are not connected.
"SB LRG"
Large size surround back speaker is
connected. (6.1ch)
"SB NML"
Average size surround back speaker is
connected. (6.1ch)
"SB OFF"
Surround back speaker is not connected.
"RMX ON"
Subwoofer re-mix is on.
"RMX OFF"
Subwoofer re-mix is off.
• If "SURR OFF" is selected, no surround back speaker can
be selected.
• If "SURR NML" is selected for surround speakers, "SB LRG"
cannot be selected for the surround back speaker and
"FH LRG" cannot be selected for the front height speaker.
Speaker Level
Adjust the volume level of the speakers so that all of them are
approximately identical.
1 Select "TEST TONE".
[SETUP]
[MULTI CONTROL ∞/5]
[SETUP]
2 Select the test tone output method.
[MULTI CONTROL ∞/5]
[SETUP]
Settings of RA-5000
Speaker
Subwoofer
Front speaker
Subwoofer
Re-mix*1
Display
Setting
"SUBW ON"
Subwoofer is connected.
"SUBW OFF"
Subwoofer is not connected.
"FRNT LRG"
Large size front speaker
"FRNT NML"
Average size front speaker
"RMX ON"
Subwoofer re-mix is on.
"RMX OFF"
Subwoofer re-mix is off.
*1 Mixes the bass tone of other channels to the subwoofer
channel.
3 Go to the next setting.
• Reference for speaker size
"LRG"(Large) :
A speaker with a sufficient bass
reproduction capability (a speaker
with a large woofer or a large cabinet
size).
"NML"(Normal) :
A speaker with a lower bass
reproduction capability than the
"LRG" speakers (the bass frequencies
will be output from the speakers set
to "LRG" and the subwoofer).
If you cannot identify the size of a speaker, it is
recommended to set it to "NML".
• When "SUBW OFF" is selected, the front speakers are
automatically set to "FRNT LRG".
• For "FRNT LRG" selection, no sound will be heard from
subwoofer even it is set to ON. If you set the Subwoofer
Remix to "RMX ON", you will be able to hear sound from
the subwoofer.
• If "FRNT NML" is selected, "LRG" cannot be selected for the
other speakers.
30
Display
Setting
"AUTO"
The test tone is heard from the speakers one after another with
2 seconds each.
"MANUAL"
You can select the speaker channel from which the test tone
is output.
3 Adjust the volume level of each speaker.
If you select "AUTO" :
When you hear the test tone from the speaker which you
wish to adjust, use [MULTI CONTROL ∞/5] and adjust the
volume of the test tone. When you finish adjusting, press
[SETUP].
If you select "MANUAL" :
Use [MULTI CONTROL ∞/5] to adjust its volume level and
press [SETUP]. You will hear the test tone from the next
speaker.
The level is adjusted from -10dB to +10dB in1dB step
decrements.
4 Go to the next setting.
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 30
10.8.3 11:08:02 AM
Speaker Distance
2 Set the distance.
Sets the distance between each speaker and the listening
position. The actual distances should be measured before starting
this setup.
Refer to the table above for the distance from each speaker
to this unit.
Adjustment starts from front left speaker.
Distances of speakers
Use [MULTI CONTROL ∞/5] to set the distance.
Measure the distance from the listening position to each speaker
and jot down in the table below.
RV-7000
Speaker
Input channel
Distance from the
listening position
meters (feet)
[SETUP]
The distance can be set in the range of 0.3 to 9.0 meters (1
to 30.0 ft) in 0.3-meter (1-feet) increments.
"LEFT"
Front Height speaker (left)
"LEFT HEIGHT"
meters (feet)
Center speaker
"CENTER"
meters (feet)
of all speakers are set.
Front Height speaker (right)
"RIGHT HEIGHT"
meters (feet)
Front speaker (right)
"RIGHT"
meters (feet)
4 Go to the next setting.
Surround speaker (right)
"SURR RIGHT"
meters (feet)
Surround Back speaker (right)
"SURR BACK RIGHT"
meters (feet)
Surround Back speaker
"SURR BACK"
meters (feet)
Surround Back speaker (left)
"SURR BACK LEFT"
meters (feet)
Surround speaker (left)
"SURR LEFT"
meters (feet)
Subwoofer
"SUBWOOFER"
meters (feet)
RV-6000
Distance from the
listening position
meters (feet)
Speaker
Input channel
Front speaker (left)
"LEFT"
Center speaker
"CENTER"
meters (feet)
Front speaker (right)
"RIGHT"
meters (feet)
Surround speaker (right)
"SURR RIGHT"
meters (feet)
Surround Back speaker (right)
"SURR BACK RIGHT"
meters (feet)
Surround Back speaker
"SURR BACK"
meters (feet)
Surround Back speaker (left)
"SURR BACK LEFT"
meters (feet)
Surround speaker (left)
"SURR LEFT"
meters (feet)
Subwoofer
"SUBWOOFER"
meters (feet)
3 Repeat step 2 for each speaker until the distances
Setup
Front speaker (left)
Crossover
The crossover frequency is the lower limit of the bass frequencies
reproduced from the speakers set to "NML" in the <Speaker
configuration>. The frequencies below the set crossover
frequency are output from other speakers (those set to "LRG" and
the subwoofer).
1 Select "CROSSOVER".
[SETUP]
[MULTI CONTROL ∞/5]
[SETUP]
2 Set the crossover frequency.
Use [MULTI CONTROL ∞/5] to select crossover frequency.
RA-5000
Distance from the
listening position
meters (feet)
Speaker
Input channel
Front speaker (left)
"LEFT"
Front speaker (right)
"RIGHT"
meters (feet)
Subwoofer
"SUBWOOFER"
meters (feet)
[SETUP]
The frequency is selected from 40, 60, 80, 100, 120, 150 and
200Hz.
3 Go to the next setting.
1 Select "DISTANCE".
[SETUP]
[MULTI CONTROL ∞/5]
[SETUP]
English
B60-5827-08_00_En.indd 31
31
10.8.3 11:08:03 AM
Setup
Speaker setup (Detailed Setup)
LFE (Low Frequency Effect) Level
APS (Auto Power Save)
Low frequency effect signal is used exclusively for giving the field
effect of bass tone in the Dolby Digital and DTS signal.
Auto Power Save (APS) is a function that automatically turns the
system off if it is not used at all for 30 minutes.
1 Select "LFE LVL".
1 Select "APS".
[SETUP]
[SETUP]
[MULTI CONTROL ∞/5]
[MULTI CONTROL ∞/5]
[SETUP]
[SETUP]
2 Set the LFE level.
Use [MULTI CONTROL ∞/5] to select the LFE level.
2 Set the APS.
Use [MULTI CONTROL ∞/5] to select "APS ON" or "APS
OFF".
[SETUP]
The level is adjusted from 0dB to -10dB in1dB step
decrements.
3 Go to the next setting.
Lip Sync
If the monitored video is delayed in time with respect to the
audio from the speakers, the audio output timing can be delayed.
[SETUP]
3 Press [SETUP] to exit the setup mode.
• Auto Power Save (APS) will function when the volume
is set to the minimum position, the sound is muted, or
the input selector is set to one of HDMI 1 to 4 but the
HDMI indicator is not lit.
1 Select "LIP SYNC".
[SETUP]
[MULTI CONTROL ∞/5]
[SETUP]
2 Set the delay time.
Use [MULTI CONTROL ∞/5] to select the delay time.
[SETUP]
The delay time is adjusted from 0ms to 300ms in 10ms step.
3 Go to the next setting.
32
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 32
10.8.3 11:08:04 AM
HDMI setup
The HDMI setup is required to use the component connected to
the HDMI terminal or to use the HDMI control functions.
Audio Out
This function selects whether the output destination of the audio
input is the TV or this unit.
1 Select "AUDIO OUT".
[HDMI SETUP]
08/7,&21752/∞/5
Use [MULTI CONTROL ∞/5].
+'0,6(783
08/7,&21752/
Setup
[HDMI SETUP]
2 Set the HDMI audio output destination.
[MULTI CONTROL ∞/5]
[HDMI SETUP]
Display
HDMI setup flow
The HDMI control functions can be set.
1 Enter the HDMI Setup mode.
[HDMI SETUP]
Use [MULTI CONTROL ∞/5] to select an item to set.
Setting
"AMP"
Outputs the audio from the speakers connected to this unit.
"TV"
Outputs the audio from the TV connected to this unit.
3 Go to the next setting.
• If "TV" is selected and the audio is not output or is
interfered with by noise, set the audio output of the
player component to PCM.
• If "TV" is selected, adjust the volume on TV.
[HDMI SETUP]
Display
Setting
"AUDIO OUT"
Sets the HDMI audio output destination.
"LIP SYNC"
Adjusts the deviation in time between
the output audio and video.
"LINK SET"
Sets whether or not the HDMI control
functions are used.
"POWER CONTROL"*1
"EXIT"
Interlocks power ON-OFF of components
by means of HDMI control.
Exits the HDMI Setup mode.
1
* This item can be set when "LINK SET" is set to "ON".
2 Set each item.
See the followings for each HDMI control item.
English
B60-5827-08_00_En.indd 33
33
10.8.3 11:08:06 AM
HDMI setup
Lip Sync
HDMI Link
If the monitored video is delayed in time with respect to the
audio from the speakers, the audio output timing can be delayed.
This function selects whether or not input selection of this
unit are interlocked with the operations of the connected
components.
1 Select "LIP SYNC".
[HDMI SETUP]
1 Select "LINK SET".
[HDMI SETUP]
Setup
Use [MULTI CONTROL ∞/5].
Use [MULTI CONTROL ∞/5].
[HDMI SETUP]
2 Set the HDMI audio delay.
[MULTI CONTROL ∞/5]
[HDMI SETUP]
2 Set the HDMI link on or off.
[MULTI CONTROL ∞/5]
[HDMI SETUP]
[HDMI SETUP]
Display
Setting
"AUTO"
Corrects the deviation in time between the output audio and
video automatically.
"MANUAL"
Allows the user to correct the deviation in time between the
output audio and video manually.
"OFF"
The deviation in time between the output audio and video is
not corrected.
Display
Setting
"LINK ON"
The HDMI control functions are used.
"LINK OFF"
The HDMI control functions are not used.
3 If "LINK ON" is set, proceed to the <Power Control>
setup.
When "MANUAL" is selected, use [MULTI CONTROL
∞/5] to select the audio delay time and press [HDMI
SETUP] to enter the setting.
The delay time is adjusted from 0ms to 300ms in 10ms step.
3 Go to the next setting.
• If the TV in use is not compatible with "AUTO", select
"MANUAL".
Power Control
This function selects whether or not the power status of this unit
is interlocked with the power ON/OFF and start of playback of the
connected components.
1 Set the HDMI power control on or off.
[MULTI CONTROL ∞/5]
[HDMI SETUP]
34
Display
Setting
"PWR ON"
Turning the TV ON/OFF also turns this unit ON/OFF with an
interlocked operation.
"PWR OFF"
The power ON/OFF status of this unit is not interlocked with the
power ON/OFF status of the TV.
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 34
10.8.3 11:08:09 AM
Confirming the HDMI function
Note that some HDMI control functions may not work with
certain components and TV that are not compatible with them.
To use the HDMI control functions properly, it is recommended to
confirm the HDMI control functions usable with each connected
component by performing the steps described below. If a
function that is not available with a connected component is
found, the related setup should be set to off before using this
unit.
Before operation
Check that this unit, the TV and the HDMI connection
capable components are connected through HDMI
cables.
•
Check that the HDMI control of the TV and the HDMIconnectable components are enabled.
(For the setups of the TV and player components, refer to
their instruction manuals.)
•
Enable the HDMI control of this unit
HDMI LINK: On, POWER CTRL: On
1 Turn all of the HDMI-connected components ON.
2 Turn the TV OFF (standby) with its remote control
unit.
Are all of the components turned OFF? (Power Control
confirmation)
3 With all of the HDMI-connected components OFF,
start playing a player component.
Are all of the components turned ON and the inputs of this
unit and the TV switched automatically? (HDMI Link and
Power Control confirmations)
Setup
•
Confirming the HDMI control functions
• The HDMI control functions are not available during the following
operations.
− During setup
− During auto memory of radio stations
Confirming the basic HDMI operations
1 Turn all of the HDMI-connected components ON.
2 Switch the TV input to an input source connected
through HDMI connection to this unit.
3 Set the input selector of this unit to select the
HDMI-connected input source and confirm that its
video is displayed and the audio is output from the
speakers properly.
English
B60-5827-08_00_En.indd 35
35
10.8.3 11:08:10 AM
Preparation for playing music or movie
Selecting the input mode
,138702'(
When playing a component connected to the digital input
terminal (CD, VIDEO or DVD) or the HDMI input terminal (HDMI 1,
HDMI 2, HDMI 3 or HDMI 4), set the input mode to match the type
of the audio input.
1 Use [INPUT SELECTOR] to select "HDMI 1", "HDMI
63($.(56
212))
,13876(/(&725∞/5
/,67(102'(
5(&(,9(5
2", "HDMI 3", "HDMI 4", "DVD", "VIDEO" or "CD"
input source.
2 Press [INPUT MODE] to select the input mode.
Each press switches the mode as follows.
Playing music or movie
When in HDMI 1, HDMI 2, HDMI 3 or HDMI 4 input
source
Display
Setting
"AUTO"
The digital and analog inputs are switched automatically
according to the input signal. When a digital input is detected,
the decode mode is also switched according to the signal type
(Multi-channel PCM/Dolby Digital/DTS).
"MANUAL"
The input mode is fixed at digital to accelerate the input signal
processing and eliminate lack of audio at the beginning of
playback.
The decode mode is also fixed according to the type of the
signal to be played.
/,67(102'(
Input source keys
When in DVD, VIDEO or CD input source
Turning on the power
Display
Setting
1 Turn the connected monitor and player component
"AUTO"
The digital and analog inputs are switched automatically
according to the input signal. When a digital input is detected,
the decode mode is also switched according to the signal type
(PCM/Dolby Digital/DTS).
"MANUAL"
The input mode is fixed at digital to accelerate the input signal
processing and eliminate lack of audio at the beginning of
playback.
The decode mode is also fixed according to the type of the
signal to be played.
"ANALOG"*1
The input mode is fixed at analog.
This is selected for playback of analog player components.
ON.
2 Press [
RECEIVER] (remote control unit) or [ ]
(main unit) to turn on the unit.
Setting the speaker system
Press [SPEAKERS ON/OFF] to switch the speaker
output on or off.
"SP" indicator lights up when turning on the speaker system.
*1 This cannot be selected when in DTS play mode.
• The "AUTO DETECT" indicator lights when "AUTO" is
selected.
• If the audio is lost as a result of change in the input signal
while "MANUAL" is selected, press [LISTEN MODE].
36
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 36
10.8.3 11:08:11 AM
Playback
92/80(&21752/
ARC (Audio Return Channel)
This function allows the audio signal from an Audio Return
Channel (ARC) compatible TV to be input into the HDMI
MONITOR terminal of this unit.
To use this function, set "LINK SET" in the HDMI setup to "ON".
Connection of ARC-compatible TV monitor
,13876(/(&725∞/5
HDMI cable
Playing music or movie
92/80( HDMI cable
Input source keys
1 Select a source.
Use the Input source keys on the remote control unit to
select a source.
Or use [INPUT SELECTOR] key on the main unit.
Example: Display when HDMI 1 input source is selected
2 Start playback from the selected source.
3 Use [VOLUME %/fi] to adjust the volume.
4 Enjoy various surround effects.
You can enjoy a variety of listen modes. (See <Surround
play using the listen mode> q.)
The surround effects can be fine tuned according to the
selected input source. (See <Adjustments according to the
playing source> o.)
Connection of ARC-incompatible TV monitor
When your TV monitor is not compatible with Audio Return
Channel (ARC), it is required to connect the optical cable.
HDMI cable
Optical cable
HDMI cable
English
B60-5827-08_00_En.indd 37
37
10.8.3 11:08:13 AM
Monitoring the input source in the original sound (STRAIGHT
DECODE mode)(RV-7000/RV-6000 only)
Listening to music with PURE AUDIO MODE
STRAIGHT DECODE mode : The signal input from a source can be
output directly without any sound field effect added to it.
No video signal to the TV monitor.
(Except the HDMI video signal)
PURE AUDIO MODE : PURE AUDIO MODE turns the display
and analog video circuitry (other than HDMI) off to eliminate
their effects on the audio circuitry. This mode thereby makes it
possible to enjoy audio with higher quality and higher fidelity to
the original sound.
The display is turned off.
385($8',202'(
Playing music or movie
The illumination is turned off.
PURE AUDIO MODE indicator
To cancel
Press [PURE AUDIO MODE].
STRAIGHT DECODE mode or PURE AUDIO MODE is also
canceled when [LISTEN MODE] or [VIRTUAL] is operated.
• If the input signal uses a number of channels larger than
the number of speakers in use, the signals are distributed
automatically according to the available speakers.
• The video other than the HDMI input video cannot be
monitored when PURE AUDIO MODE is selected.
385($8',2
02'(
1 Select a source.
2 Start playback from the selected source.
3 Press [PURE AUDIO MODE] to select the mode.
Each press switches the mode as follows.
Mode
Display
Straight decode mode "STRAIGHT" indicator is on.
Pure audio mode
PURE AUDIO MODE indicator is on.
Off
STRAIGHT and PURE AUDIO MODE indicators are off.
When STRAIGHT DECODE mode or PURE AUDIO MODE
is enabled, the listen mode is selected automatically
according to the input signal.
When PURE AUDIO MODE is enabled, the display is turned
off and the video signal other than the HDMI input is not
output to the TV monitor.
38
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 38
10.8.3 11:08:16 AM
Listen mode
The listen modes provided with this unit allow you to enjoy various surround effects with various video software. To enjoy the surround
audio in the best condition, it is required to set up the speakers in advance.
Terminal
RV-7000
Input Signal
HDMI
RA-5000
Dolby TrueHD
✔
Dolby Digital Plus
✔
DTS-HD Master Audio
DTS-HD High
Resolution Audio
PCM (Multi Channel)
✔
✔
✔
DSD
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
DTS
✔
✔
✔
PCM (2 Channel)
✔
✔
✔
Analog
✔
✔
✔
✔
DIGITAL IN
Dolby Digital EX
(OPTICAL/COAXIAL)
Dolby Digital
DTS-ES (Discrete,
Matrix)
DTS 96/24
✔
✔
Surround effects
AUDIO IN
RV-6000
RV-7000
7.1ch surround system
(Front Height speaker)
LH
L
TV / SCREEN
SW
C
7.1ch surround system
(Surround Back speaker)
RH
R
SL
L
SR
6.1ch surround system
TV / SCREEN
TV / SCREEN
SW
SW
C
R
SL
L
SR
SBL
SBR
C
SL
R
SR
SB
Listen mode
Listen mode
Listen mode
· Dolby Pro Logic IIz (Height)
· Dolby Pro Logic II
(Movie, Music, Game)
· Dolby Pro Logic
· Neo:6 (Cinema, Music)
· Stereo
· Dolby Pro Logic IIx
(Movie, Music, Game)
· Dolby Pro Logic
· Dolby EX
· Neo:6 (Cinema, Music)
· Neo:6
· Stereo
· Dolby Pro Logic IIx
(Movie, Music, Game)
· Dolby Pro Logic
· Dolby EX
· Neo:6 (Cinema, Music)
· Neo:6
· Stereo
Continued
English
B60-5827-08_00_En.indd 39
39
10.8.3 11:08:18 AM
Listen mode
5.1ch surround system
2ch stereo system
TV / SCREEN
TV / SCREEN
L
SW
C
R
Surround effects
SL
R
L
SR
Listen mode
Listen mode
· Dolby Pro Logic II
(Movie, Music, Game)
· Dolby Pro Logic
· Neo:6 (Cinema, Music)
· Stereo
· Stereo
RV-6000
6.1ch surround system
5.1ch surround system
TV / SCREEN
L
SW
C
SL
2ch stereo system
TV / SCREEN
TV / SCREEN
R
L
SR
SW
C
SL
R
L
R
SR
SB
Listen mode
Listen mode
Listen mode
· Dolby Pro Logic IIx
(Movie, Music, Game)
· Dolby Pro Logic
· Neo:6 (Cinema, Music)
· Neo:6
· Stereo
· Dolby Pro Logic II
(Movie, Music, Game)
· Dolby Pro Logic
· Neo:6 (Cinema, Music)
· Stereo
· Stereo
• Certain listen modes cannot be selected depending on the input signal.
40
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 40
10.8.3 11:08:19 AM
Surround play using the listen
mode
RA-5000
2.1ch stereo system
Select the listen mode according to the source being played back.
TV / SCREEN
L
SW
R
/,67(102'(
5959
Listen mode
Dolby Virtual Speaker Off
· Stereo
L:
LH :
SW :
C:
R:
RH :
SL :
SR :
SB :
SBL :
SBR :
Front Left speaker
Front Height Left speaker
Subwoofer
Center speaker
Front Right speaker
Front Height Right speaker
Surround Left speaker
Surround Right speaker
Surround Back speaker
Surround Back Left speaker
Surround Back Right speaker
Preparations
• Turn the components to be used ON.
• Complete <Speaker setup>.
• Select the source you wish to play back with
surround sound.
• Select the input mode fl.
(When the input mode is set to "AUTO" (i.e. when
the "AUTO DETECT" indicator is lit), the listen
mode matching the input signal type and speaker
setups is selected automatically. Noise may be
produced when a DTS source is played by selecting
the analog input.)
Surround effects
Dolby Virtual Speaker On
· Dolby Pro Logic II
(Movie, Music)
· Neo:6 (Cinema, Music)
/,67(102'(
1 Start playing the selected source.
2 Use [LISTEN MODE] to select the listen mode.
Each press switches the listen mode.
• RA-5000 :
The listen mode can be selected when Dolby Virtual
Speaker is on (when the input is the 2ch signal).
• Certain listen modes cannot be selected depending on
the input signal.
English
B60-5827-08_00_En.indd 41
41
10.8.3 11:08:19 AM
Checking the current input
signal
The type and number of channels of the audio signal input can
be checked.
',63/$<
Virtual Surround
(RV-7000/RV-6000)
Dolby Virtual Speaker
(RA-5000)
These modes allow you to enjoy surround sound even when you
connect only the front speakers.
1 Press [DISPLAY].
The input signal names and the numbers of their channels
are displayed in scrollable format.
Example: Display with DTS 5.1-channel input
9,578$/6855281'5959
'2/%<9,578$/63($.(55$
Surround effects
9,578$/
• After displaying the type of listen mode and its number of
input channels, the display will switch back to the input
source name.
• This function is not available when in Tuner source.
1 Press [VIRTUAL] (remote control unit) or [VIRTUAL
SURROUND]/[DOLBY VIRTUAL SPEAKER] (main
unit).
Each press switches the mode as follows:
RV-7000/RV-6000 only
Display
Setting
"VS ON"
Sets Virtual Surround mode to “ON”..
"VS OFF"
Sets Virtual Surround mode to “OFF”..
RA-5000 only
42
Display
Setting
"DOLBY VS REF"
Provides the virtual surround effect. This is the standard setting.
"DOLBY VS WIDE"
Provides the virtual surround effect with a wider expansion and
spatial feeling.
"DOLBY VS OFF"
Sets Dolby Virtual Speaker mode to off
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 42
10.8.3 11:08:21 AM
Tuning into a radio station
This unit can store up to 40 stations in the memory and recall
them by easy operation.
Radio stations can be classified into Radio Data System stations
and other stations. To listen to or store Radio Data System stations
in the preset memory see <Using Radio Data System>.
4 Use [TUNING 1/¡] to select the station.
"TUNED" lights when a broadcast is being received.
"ST" lights when a broadcast is being received in stereo.
Be sure to connect antennas to receive radio broadcasts. (See
<Connecting antennas> §.)
%$1'
$8720212
,13876(/(&725∞/5
• [MULTI CONTROL ∞/5] can also be use to select a
station.
08/7,&21752/∞/5
%$1'
Listening to radio broadcasts
08/7,&21752/
$8720212
781,1*
781(5
1 Set the input source to TUNER.
2 Use [BAND] to select the broadcast band.
Each press switches the band as follows:
1 FM
2 AM
3 Use [AUTO/MONO] to select the tuning method.
Each press switches the tuning method as follows:
Setting
Operation
Auto tuning
The next station is tuned automatically.
Indicator
"AUTO" lit
Manual tuning
Select a station manually.
"AUTO" not lit
Normally, set to "AUTO" (auto tuning). If the radio waves are
weak and there is a lot of interference, switch to manual
tuning. (With manual tuning, stereo broadcasts will be
received in monaural.)
English
B60-5827-08_00_En.indd 43
43
10.8.3 11:08:23 AM
Using Radio Data System
Radio Data System is a system that transmits useful information
(in the form of digital data) for FM broadcasts along with the
broadcast signal. Tuners and receivers designed for Radio Data
System reception can extract the information from the broadcast
signal for use with various functions, such as automatic display of
the station name.
Before using a function utilizing the Radio Data System, be
sure to perform the Auto Memory operation by referring to the
description in <Auto Memory>.
Auto Memory
This function automatically stores up to 40 Radio Data System
stations in the preset memory. In order to use the PTY function,
the Radio Data System stations must be stored in the preset
memory using the AUTO MEMORY function.
$8720(025<
AUTO MEMORY function
Automatically selects and stores up to 40 Radio Data
System stations in the preset memory.
If fewer than 40 Radio Data System stations have been
stored in the preset memory, regular FM stations will be
stored in the remaining places.
PS (Program Service) Name Display
Automatically displays the station name transmitted by the
Radio Data System station.
%$1'
PTY (Program TYpe) identification Search
Automatically tunes to a station that is currently
broadcasting the specified program type (genre).
Listening to radio broadcasts
RT (Radio Text) function
44
Displays the radio text data transmitted by some Radio
Data System stations when you press [DISPLAY]. There is
"NO RT" display if no text data is transmitted.
781(5
1 Press [TUNER] to select the tuner.
2 Press [BAND] to set the broadcast band to "FM".
3 Press [AUTO MEMORY] to start auto memory.
The "RDS" indicator lights up when an Radio Data
System broadcast (signal) is received.
• Some functions and function names may differ for certain
countries and areas.
After a few minutes, up to 40 Radio Data System stations
are preset in order from channel "01".
Stations already stored in the preset memory may be
replaced by Radio Data System stations. (i.e., If the AUTO
MEMORY function detects 15 Radio Data System stations,
the stations currently preset at numbers 01–15 will be
replaced by the Radio Data System stations.)
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 44
10.8.3 11:08:25 AM
Presetting radio stations
manually
The Radio Data System auto memory function assigns preset
numbers to Radio Data System stations starting from preset
number "1". Therefore, be sure to execute the Radio Data System
auto memory function before using the following operations to
manually store AM stations and other FM stations, and Radio Data
System stations.
See <Auto Memory>.
Receiving preset stations
Numeric keys
0(025<
08/7,&21752/
781(5
1 Press [TUNER] to select tuner as the source.
2 Enter the number of the preset station you want to
receive (up to "40" preset numbers).
Preset number
Proceed to step 3 within 20 seconds.
If more than 20 seconds elapse, press [MEMORY] again.
• If you make a mistake entering a two digit number, press
[+10] repeatedly to return to the original display and start
again.
3 Use [MULTI CONTROL ∞/5] to select one of the
station presets (1 – 40).
4 Press [MEMORY] to confirm the setting.
Listening to radio broadcasts
1 Tune in the station you want to store.
2 Press [MEMORY] while receiving the station.
Press the Numeric keys in the following order:
For preset No.15: [+10] and [5]
For preset No.20: [+10], [+10] and [0]
Repeat steps 1 to 4 to store as many stations as necessary.
If you store a station at a previously used preset, the
previous station will be replaced by the new one.
English
B60-5827-08_00_En.indd 45
45
10.8.3 11:08:26 AM
Receiving preset stations in
order (P.CALL)
Tuning by program type
(PTY search)
This function lets you set the tuner to automatically search for
stations which are currently broadcasting the type of program
(genre) you want to listen to.
Under certain receiving conditions, it may take more than 1
minute to complete the search.
37<
08/7,&21752/
3&$//
781(5
Listening to radio broadcasts
1 Press [TUNER] to select tuner as the source.
2 Use [P.CALL 4/¢] to select the desired station.
46
Each time you press the key, another preset station is
received in order.
Holding down the [P.CALL 4/¢] lets you skip through
the presets, receiving each preset station at 0.5 second
intervals.
Preparations
• Execute the Radio Data System auto memory
procedure.
• Set the broadcast band to FM.
• Tune to an Radio Data System station.
1 Press [PTY] to activate the PTY search mode.
When an Radio Data System broadcast is received, the
program type is shown on the display. If no PTY data is
available, or if the station is not an Radio Data System
station, "NONE" is displayed.
2 While the "PTY" indicator is lit, use [MULTI CONTROL
∞/5] to select the program type of your choice.
Program type
Pop Music
Rock Music
Easy Music
Light Classical Music
Serious Classical Music
Other Music
News
Current Affairs
Information
Sport
Education
Drama
Culture
Science
Varied Speech
Display
"POP M"
"ROCK M"
"EASY M"
"LIGHT M"
"CLASSICS"
"OTHER M"
"NEWS"
"AFFAIRS"
"INFO"
"SPORT"
"EDUCATE"
"DRAMA"
"CULTURE"
"SCIENCE"
"VARIED"
Program type
Weather
Finance
Children's Program
Social Affairs
Religion
Phone In
Travel
Leisure
Jazz Music
Country Music
National Music
Oldies Music
Folk Music
Documentary
Display
"WEATHER"
"FINANCE"
"CHILDREN"
"SOCIAL"
"RELIGION"
"PHONE IN"
"TRAVEL"
"LEISURE"
"JAZZ"
"COUNTRY"
"NATION M"
"OLDIES"
"FOLK M"
"DOCUMENT"
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 46
10.8.3 11:08:28 AM
Using the DISPLAY key
3 Press [PTY] to start searching.
',63/$<
Example: Searching for a Rock Music broadcast.
Display while searching.
Blinks
Display when a station is received.
Goes out
1 Pressing [DISPLAY] changes the contents of the
display.
Station name display
No sound is heard while "PTY" is blinking.
If the desired program type cannot be found, "NO PROG" is
displayed, then after several seconds the display returns to
the original display.
To select another program type
Repeat steps 1, 2 and 3.
Each press switches the display mode as follows:
1 PS (Program Service) name display
2 RT (Radio Text) display
3 Frequency display
1 PS (Program Service) name display:
The station name is displayed automatically when an Radio
Data System broadcast is received.
If no PS data was sent, "NO PS" is displayed.
Text data accompanying the Radio Data System broadcast
scrolls across the display. "NO RT" is displayed if the current
Radio Data System station does not provide RT data.
3 Frequency display:
Displays the frequency of the current station.
English
B60-5827-08_00_En.indd 47
Listening to radio broadcasts
2 RT (Radio Text) display:
47
10.8.3 11:08:29 AM
Adjusting the sound
Bass Boost
The Bass Boost can be adjusted when the input signal is a PCM or
analog signal and the listen mode of this unit is set to "STEREO",
and also ACTIVE EQ mode is set to "OFF".
1 Press [BASS BOOST].
08/7,&21752/∞/5
721(5$
$&7,9((4
%$66%2267
721(
Press the key once to select the maximum (+10) low
frequency emphasis setting.
TONE will automatically be turned ON.
To cancel
Press [BASS BOOST] again.
Adjusting the Tone
08/7,&21752/
ACTIVE EQ mode
The optimum acoustic field effect can be selected according to
the purpose of playback.
1 Press [ACTIVE EQ].
The tone level can be adjusted when the input signal is a PCM or
analog signal and the listen mode of this unit is set to "STEREO",
and also ACTIVE EQ mode is set to "OFF".
1 Press [TONE].
2 Select whether or not the tone level is to be
adjusted.
Use [MULTI CONTROL ∞/5] to select "TONE ON" or "TONE
OFF".
Sound adjustment
Each press switches the mode as follows:
[TONE]
Display
Setting
"A-EQ MUSIC"
Effective when listening to music.
Display
"A-EQ CINEMA"
Effective when watching a movie.
"TONE ON"
The tone level can be adjusted. Go to step 3 after setting.
"A-EQ GAME"
Effective when playing a game.
"TONE OFF"
The tone level is not adjusted.
"A-EQ OFF"
Active EQ function is off.
Setting
3 Adjust the level of "BASS" (low frequencies).
Use [MULTI CONTROL ∞/5] to adjust the level.
[TONE]
The level is adjusted from –10 to +10.
4 Adjust the level of "TREB" (high frequencies).
Use [MULTI CONTROL ∞/5] to adjust the level.
[TONE]
The level is adjusted from –10 to +10.
48
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 48
10.8.3 11:08:31 AM
Adjustments according to the playing source
Settings of RV-6000
The audio can be adjusted as desired according to the source
being played.
08/7,&21752/∞/5
Display
Setting item
Range
"C"
Center speaker level
-10 – +10dB
"SR"
Surround Right speaker level
-10 – +10dB
"SB"
Surround Back speaker level
-10 – +10dB
"SL"
Surround Left speaker level
-10 – +10dB
"SW"
Subwoofer level
-10 – +10dB
"INPUT"
Input level
-6, -3, 0
*2
"MIDNIGHT"
Midnight mode
"ON", "OFF"
*3
"PANORAMA"
Panorama mode
"ON", "OFF"
"DIMENSION"
Dimension
*1
*4
"CENTER WIDTH" Center Width
"CENTER IMAGE" Center Image
6281'
Input source
name
08/7,&21752/
mode.
Each press switches the mode as follows.
Note that some items are not displayed depending on
speaker settings and listen mode.
Settings of RV-7000
Range
"LH"
Left Height speaker level
-10 – +10dB
"C"
Center speaker level
-10 – +10dB
"RH"
Right Height speaker level
-10 – +10dB
"SR"
Surround Right speaker level
-10 – +10dB
"SBR"
Surround Back Right speaker level
-10 – +10dB
"SB"
Surround Back speaker level
-10 – +10dB
Surround Back Left speaker level
-10 – +10dB
"SL"
Surround Left speaker level
-10 – +10dB
"SW"
Subwoofer level
-10 – +10dB
"INPUT"
Input level
-6, -3, 0
*2
Midnight mode
"AUTO", "ON",
"OFF"
*3
"MIDNIGHT"
"PANORAMA"
Panorama mode
"DIMENSION"
Dimension
Input source
name
Subwoofer level
-10 – +10dB
"INPUT"
Input level
-6, -3, 0
*2
"MIDNIGHT"
Midnight mode
"ON", "OFF"
*3
Input source
name
Exit the adjustment mode.
Range
2 Use [MULTI CONTROL ∞/5] to adjust the desired
item.
"ON", "OFF"
*4
0.0 – 1.0
Setting item
"SW"
For detailed adjustment method, see the explanation of
each item.
"CENTER WIDTH" Center Width
"CENTER IMAGE" Center Image
Display
*1 The adjustment is only temporary for the current input
selection. The value will return automatically to the original
setup value when the power is turned on/off or when the
input selection is changed.
*2 Analog source only
*3 Dolby TrueHD, Dolby Digital Plus, Dolby Digital, DTS-HD and
DTS signal only.
"AUTO" can be selected only in the Dolby TrueHD signal.
*4 Pro Logic II Music mode and Pro Logic IIx Music mode only
*5 Neo:6 Music mode only
*6 "CENTER WIDTH" and "CENTER IMAGE" can be selected only
when the center speaker is installed.
*1
"SBL"
Exit the adjustment mode.
Sound adjustment
Setting item
*6
*5
Settings of RA-5000
1 Press [SOUND] to enter the surround adjustment
Display
0.0 – 1.0
*5
To exit the sound adjustment mode
*6
Press [SOUND].
Exit the adjustment mode.
English
B60-5827-08_00_En.indd 49
49
10.8.3 11:08:33 AM
Adjustments according to the playing source
Speaker level adjustment
Midnight mode
The output level from the desired speaker channels can be fine
adjusted according to the properties of each source.
The adjustment is only temporary for the current input selection.
The value will return automatically to the original setup value
when the power is turned on/off or when the input selection is
changed.
¶ Dolby TrueHD, Dolby Digital Plus/Dolby Digital and DTS-HD/
DTS mode only
1 Press [SOUND] repeatedly to select the speaker to
adjust.
When watching movies at night, you might not be able to raise
the volume as loud as normal. Midnight mode compresses the
dynamic range of previously specified heavy sound passage of
the Dolby TrueHD, Dolby Digital Plus/Dolby Digital and DTSHD/DTS mode sound track (like scenes with sudden increases
in volume) to minimize the difference in volume between the
scenes with heavy sound passage and scenes with normal sound
passage. This makes it easy to hear all of the sound track, even
when listening at low volumes.
1 Press [SOUND] repeatedly to select "MIDNIGHT".
2 Use [MULTI CONTROL ∞/5] to adjust the level.
2 Use [MULTI CONTROL ∞/5] to select "AUTO" or
"ON" or "OFF".
3 Repeat steps 1 and 2 to adjust the level of other
speakers.
Input level adjustment
Display
Setting
"AUTO"
Switches the Midnight mode automatically.
"ON"
Midnigt mode is on.
"OFF"
Midnigt mode is off.
¶ Analog source only
Sound adjustment
If the input level of an analog source signal is too high, the CLIP
indicator will light to indicate. Adjust the input level.
• Some Dolby TrueHD, Dolby Digital Plus/Dolby Digital and
DTS-HD/DTS software may not be compatible with the
Midnight mode.
• "AUTO” can be selected only in the TrueHD mode.
1 Press [SOUND] repeatedly to select "INPUT".
Panorama mode (RV-7000/RV-6000 only)
¶ Pro Logic IIx Music and Pro Logic II Music mode only
2 Use [MULTI CONTROL ∞/5] to adjust the input
level.
The acoustic field of the front channels can be expanded till the
field of surround channels, which makes it possible to create
sound expansion in the front of the listener.
1 Press [SOUND] repeatedly to select "PANORAMA".
2 Use [MULTI CONTROL ∞/5] to select "ON" or "OFF".
50
Display
Setting
"ON"
PANORAMA mode is on.
"OFF"
PANORAMA mode is off.
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 50
10.8.3 11:08:35 AM
Dimension (RV-7000/RV-6000 only)
Center image (RV-7000/RV-6000 only)
¶ Pro Logic IIx Music and Pro Logic II Music mode only
¶ DTS Neo:6 Music mode only
The center of the acoustic field can be moved toward the front
or rear.
The output level of the center speaker can be adjusted.
1 Press [SOUND] repeatedly to select "DIMENSION".
1 Press [SOUND] repeatedly to select "CENTER
2 Use [MULTI CONTROL ∞/5] to move the acoustic
2 Use [MULTI CONTROL ∞/5] to adjust the center
field to the front or rear.
IMAGE".
speaker output.
Dimension indicator
More part of the center channel audio is distributed to the front left and
right speakers as the number increases.
Sound center moved
toward the rear
Sound center moved
toward the front
• This setup is not available when the center speaker setup
is "OFF".
Center width (RV-7000/RV-6000 only)
¶ Pro Logic IIx Music and Pro Logic II Music mode only
The center channel audio can be distributed to the front left and
right speakers to enhance the width of the sound in front of the
listener.
Sound adjustment
1 Press [SOUND] repeatedly to select "CENTER
WIDTH".
2 Use [MULTI CONTROL ∞/5] to move the acoustic
field to the left or right.
Center width indicator
When the indicator extends to the left and right wider, more part of the
center channel audio is distributed to the front left and right speakers.
• This setup is not available when the center speaker setup
is "OFF".
English
B60-5827-08_00_En.indd 51
51
10.8.3 11:08:38 AM
Convenient functions
92/80(&21752/
Listening with headphones
1 Press [SPEAKERS ON/OFF] so that the speaker
indicator goes off.
Make sure the "SP" indicator is turned off.
63($.(56212))
',00(55$
Illumination
If you turn off all of the speakers when in surround mode,
the surround mode will be canceled as well, resulting in
stereo playback.
2 Connect headphones to the [PHONES] jack.
92/80( 3+21(6
087(
',00(5
Display dimmer adjustment
Convenient functions
The dimmer function lets you select the brightness of the display
and indicators of this unit. You might find this useful if you darken
your room to watch movies or listen to music.
1 Press [DIMMER].
The brightness of the display changes among the three
available settings. Select the brightness level you find most
pleasing.
1 Slightly dark
2 Dark
3 Normal
3 Adjust volume.
¤CAUTION
Excessive sound pressure from earphones or headphones can
cause hearing loss.
Muting the sound
1 Press [MUTE].
"MUTE" indicator blinks.
• When Dark is selected, the illumination is turned off.
To cancel
Press [MUTE] again so that the "MUTE" indicator goes off.
MUTE can also be deactivated by adjusting volume.
52
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 52
10.8.3 11:08:41 AM
Remote control operations for Kenwood BD/DVD players
The remote control of this unit can control Kenwood BD/DVD players directly without using the remote control supplied with the BD/DVD
player.
Compatible BD/DVD player models
DV-4900, DV-4070B, DV-2070, DV-203, DVF-9010, DVF-K7010, DVF-5010, DVF-R9030, DVF-R7030, DVF-3530, DV-402, DV-5900, DV-5700,
DVF-R9050, DVF-J6050, DV-505, DV-503, DV-502, DVF-3550, DVF-3050, DVF-R4050, DVF-605, DV-6050, DVF-R5060,
DVF-3060, DVF-3060K, DV-705, DVF-R5070, DVF-3070, DVF-3080, DVF-N7080, DVF-8100, DVF-3200, DVF-3250, DVF-3300, DVF-3400,
DVF-5400, DVF-3500 and DVF-5500.
How to operate the BD/DVD player with the remote control
1 Press [ BD/DVD] to turn the BD/DVD player on.
2 Press [DVD] to operate the functions of the BD/DVD player.
Pressing [DVD] allows you to control the connected Kenwood BD/DVD player with this remote control unit.
The BD/DVD player can also be controlled with the HDMI1, HDMI2, HDMI3, HDMI4, VIDEO and CD keys.
3 Press each key for BD/DVD player operation. Refer to the operation manual of the BD/DVD players for the
detailed operating instructions.
(To return to the receiver operation mode, press other Input source key.)
BD/DVD player operation keys
%''9'6WHS1
32383
$8',2
68%7,7/(
+20(7230(18
Convenient functions
1XPHULFNH\V
',6&0(180(18
(17(5
&XUVRU
&XUVRU
&XUVRU
&XUVRU
(17(5
216&5((1
5(7851
3DXVH
3OD\
6WRS
087(
6HDUFK
6HDUFK
6NLS
6NLS
'9'6WHS2
English
B60-5827-08_00_En.indd 53
53
10.8.3 11:08:44 AM
Troubleshooting
Amplifier
Symptom
No sound from the speakers.
Cause
The speaker cords are disconnected.
VOLUME is set to the minimum position.
MUTE is ON.
The SPEAKERS switches are set to OFF.
The input source selection is incorrect.
The input mode is not set properly.
The standby indicator blinks and sound is not output.
Audio signal may not be output depending on the
connecting method and connected components.
Speaker cords are short-circuited.
Sound is not output from one of the speakers.
The speaker cord is disconnected.
The speaker is not set up correctly.
Sound is not output from the surround
speakers and/or the center speaker, or their sound is
very soft.
The audio cannot be played in the desired signal format
(Dolby Digital or DTS).
Some speakers do not output audio depending on the
listen mode.
The surround speaker cords and/or the center speaker
cord is disconnected.
Digital connection is necessary to play the Dolby Digital,
or DTS input signal in the input signal format.
Troubleshooting
The player component is not set for digital output.
When playing a Dolby Digital or DTS source, the sound is
cut off soon after it starts.
No sound is produced during playback from a BD/DVD
player.
A video source cannot be recorded normally.
The audio of a digital broadcast cannot be switched.
There are many possible causes for this problem,
depending on the player used.
The input mode is set to "MANUAL".
Display is turned off.
The software is copy-guarded.
The audio of certain broadcasts cannot be switched with
this unit.
PURE AUDIO MODE is on.
This unit is turned OFF spontaneously.
APS is ON.
Audio is not output when the TV input is selected.
The TV is ARC-incompatible.
The HDMI terminal is ARC-incompatible.
The HDMI Link is OFF.
54
Remedy
Connect it properly referring to <Connecting speakers>.
^–(
Adjust the volume to a proper level.
Turn OFF the MUTE.
W
Set the SPEAKERS switch to ON.
fl
Select the input source you want to play.
Select the optimum input mode by referring to
<Selecting the input mode>.
fl
Refer to the instruction manuals that come with the
connected components.
Turn the power off, eliminate the short-circuiting, then
turn on the power again.
If the standby indicator still blinks after eliminating the
short-circuiting, there may be an internal defect. Switch it
off, unplug the power cord and call for service.
Connect it properly referring to <Connecting speakers>.
^–(
Set it up properly referring to <Speaker setup>.
After setting, confirm that the test tone is output.
•ªº
Connect it properly referring to <Connecting speakers>.
^–(
Confirm that the input signal is connected to the
digital input or HDMI input terminal by referring to
<Connections>.
$–¶
Confirm the audio output setup of the player component
by referring to its instruction manual.
Set the input mode to "MANUAL" before starting playback
of the Dolby Digital or DTS source.
fl
Press the [INPUT MODE] key to select to "AUTO".fl
Copy-guarded video software cannot be recorded.
Switch the audio on the digital tuner.
While the PURE AUDIO MODE is on, the display is turned
off. Turn off the PURE AUDIO MODE.
°
Turn OFF the APS.
¤
Connect to the HDMI terminal of an ARC-compatible TV.
‡
Connect to the ARC-compatible HDMI terminal.
Set the HDMI Link to ON.
›
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 54
10.8.3 11:08:44 AM
Symptom
The video is not output or is disturbed.
Cause
The video component is not connected properly.
Video signal may not be output depending on the
connecting method and connected components.
The input of the TV monitor is not set properly.
A non NTSC/PAL video signal is input.
PURE AUDIO MODE is set to "ON".
Remedy
Connect it properly by referring to <Connections>.
$–¶
If the video component is connected to this unit through
HDMI connection, the digital video signal input from the
HDMI input terminals is output only at the HDMI monitor
output terminal.
Refer to the instruction manuals that come with the
connected components.
Confirm the input setup of the TV monitor.
Set the video setup of the video player component to
NTSC/PAL. Refer to the instruction manual of the video
player component.
If PURE AUDIO MODE is set to "ON",
the video circuitry is switched off and only the input HDMI
video can be output. Set PURE AUDIO MODE to "OFF".
°
Tuner
Symptom
Radio stations cannot be received.
Interference
Remote control unit
Symptom
Remote control operation is not possible.
Cause
Remedy
No antenna is connected.
Connect an antenna.
§
The broadcast band is not set properly.
Set the broadcast band properly.
e
The frequency of the desired station is not tuned.
Tune in the frequency of the desired station. e
Install the outdoor antenna away from the road.
Turn off the power to the appliance.
Install the unit farther away from the TV.
Noise due to ignition of an automobile.
Noise due to interference from an electric appliance.
Noise due to a nearby TV set.
Cause
The remote control unit is too far away from the main
system, controlling angle is too large, or there is an
obstacle between this unit and the remote.
There is an obstacle between this unit and the remote
control unit.
Remedy
Press the appropriate Input Source key to select the source
you wish to control.
Press the [DVD] key to activate the operation mode for the
component you want to control before operation.E
Replace with new batteries.
!
Operate the remote control unit within the controllable
range.
!
Remove the obstacle.
Resetting the unit
Troubleshooting
The remote control is not set to the source operation
mode you wish to control.
The remote control has not been changed to the
operation mode for the Kenwood BD/DVD player you
wish to control.
Batteries are exhausted.
If the unit is completely inoperable, the display is not normal or a problem cannot be solved even after checking the list in
<Troubleshooting>, it is required to reset the the unit.
While holding down [ ] key on the unit, unplug the power cord and plug it back in.
• Please note that resetting the unit will clear the contents of the memory and return the unit to the state it was in when it left the factory.
English
B60-5827-08_00_En.indd 55
55
10.8.3 11:08:44 AM
Glossary
Dolby Digital
Dolby TrueHD
Digital multi-channel audio standard developed by Dolby
Laboratories. It supports transmission and recording of highquality digital audio signals from monaural up to 5.1 channels
using an amount of data that is a fraction of the PCM audio
format. The main features of Dolby Digital include:
This loss-less (reversible) audio technology has been developed
by Dolby Laboratories and reproduces high-quality studiomastered audio data perfectly with bit-order accuracy. It is
compatible with up to 7.1 channels when the sampling frequency
is 95 kHz and up to 5.1 channels when the sampling frequency is
192 kHz.
• Downmixing optimized for monaural, stereo and Pro Logic
configurations as well as for playback of 6.1-channel audio.
• Transfer of information related to the dynamic range and the
conversation level adjustment.
• Wide range of operating bit rates.
Dolby Digital EX/Dolby EX
These extensions of Dolby Digital add the surround back channel
to the Dolby Digital channels to deliver a surround effect with
enhanced presence and listener envelopment.
Dolby Pro Logic II
This is a matrix decoding technology developed by Dolby
Laboratories. It generates 5-channel surround audio with
rich feeling of presence from any stereo source, delivering an
excellent multidimensional sound field effect even from an
ordinary stereo music content including CD music. It offers three
modes including the Movie mode optimized for movie playback,
the Music mode for music playback and the Game mode for
game play.
Dolby Virtual Speaker
This is a speaker virtual technology that can generate an ideal
5.1-channel home theater environment using only a pair of
speakers.
DTS Digital Surround
Digital surround format developed by DTS Corporation. It
features low compression rate and high sound quality, and is
capable of reproducing max. 5.1 channels.
DTS-ES
This is a 6.1-channel audio technology developed by adding the
surround back channel to DTS Digital Surround.
The signal of this format can also be played on existing DTS
5.1-channeel components. DTS-ES consists of two types, which
are DTS ES Matrix and DTS-ES Discrete 6.1.
DTS-ES Matrix
Dolby Pro Logic IIx
Matrix decoding technology developed by improving Dolby
Pro Logic II. It accepts any stereo or 5.1-channel audio input
and generates 7.1-channel surround audio with a more natural,
smoother surround sound field. It also offers three modes
optimized for each source content, including the Movie mode
for movie playback, the Music mode for music playback and the
Game mode for game play.
Troubleshooting
Dolby Pro Logic IIz
Dolby Pro Logic IIz adds front height channels to surround sound,
creating a 7.1 playback system for home music, movies, and video
games.
Dolby Pro Logic IIz brings enhanced spatial effects, added depth,
and an overall airiness to the listening experience.
Dolby Digital Plus
This is an audio technology developed based on Dolby Digital by
improving both the sound quality and functions. It delivers multichannel surround audio with completely discrete channels. The
compatible bit rates have been expanded to between 32 kbps
and 6 Mbps from between 96 and 640 kbps with Dolby Digital.
The excellent coding efficiency makes this technology capable
of delivering quality audio in max. 7.1 channels without
affecting the bit rates assigned for the video and other services.
Compatibility with existing home theater systems incorporating
the Dolby Digital technology is also secured.
56
With this format, the audio for the surround back channel added
to the DTS 5.1-channel audio is allocated to the two surround
channels during recording. When the signal is decoded, the audio
for the surround back channel is restored from the surround
channels to deliver the 6.1-channel audio.
DTS-ES Discrete
With this format, the audio for the surround back channel added
to the DTS 5.1-channel audio is recorded in an independent
channel.
DTS Neo:6
This is a matrix decoding technology developed by DTS
Corporation, capable of delivering max. 6.1 channels from any
2-channel source. It includes two modes, including the DTS Neo 6
CINEMA mode optimized for movie playback and the DTS Neo 6
MUSIC mode optimized for music playback.
DTS 96/24
5.1-channel digital audio format developed as an evolution of the
DTS 5.1-channel format. It enables high-quality playback with 96
kHz sampling frequency and 24-bit quantization (the signal of
this format can also be reproduced on existing DTS 5.1-channel
player components).
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 56
10.8.3 11:08:45 AM
DTS−HD Master Audio
This loss-less (reversible) audio technology has been developed
by DTS Corporation and reproduces audio in the same high
quality as the studio-mastered audio data. With 96 kHz sampling
frequency and 24-bit quantization, it is compatible with max.
7.1 channels. This technology can be played with any of seven
speaker layout patterns, making the content producer capable
of delivering the intended sound effects in a variety of audio
reproduction environments of users.
• 3D Over HDMI
This unit is able to pass through 3D mandatory formats
defined by HDMI Licensing, LLC, Frame Packing, Side-by-Side
Horizontal and Top-and-Bottom.
DVI
DVI (Digital Visual Interface) is the standard for connection
between PC and display.
DTS-HD High Resolution Audio
HDCP
This is an extension of the previous DTS audio format and can
record 7.1-chanenl audio with 96 kHz sampling frequency and 24
quantization bits. The multi-channel sound recorded with DTSHD High Resolution Audio can reproduce details more clearly and
realistically than the audio of DVD-Video.
HDCP (High-bandwidth Digital Contents Protection) is copyright
protection technology for prevention of illegal duplication of
video contents. It is used in encryption of digital interfaces such
as DVI and HDMI.
This technology can also be played with any of seven speaker
layout patterns, making the content producer capable of
delivering the intended sound effects in a variety of audio
reproduction environments of users.
DTS-HD Low Bit Rate
One of the DTS-HD audio formats. It is the low bit rate for use in
communications including the Internet communications.
PCM
PCM (Pulse Code Modulation) is a method of encoding audio
signal digitally without compression.
DSD (Direct Stream Digital)
DSD is audio signals used for the Super Audio CD (SACD).
HDMI
Troubleshooting
HDMI (High-Definition Multimedia Interface) is a standard
developed based on DVI (Digital Visual Interface) and features the
capability of transferring both non-compressed digital video and
multi-channel digital audio through a single cable.
This unit is compatible with the HDMI optional functions listed
below.
• Deep Color
Video signals with a larger number of bits per color component
than ordinary 8 bits, such as the 10-bit and 12-bit signals can
be transferred to achieve richer expression of gradations.
• x.v.Color
A larger variety of colors, or about 180% more colors than the
number of colors of sRGB color space, can be reproduced.
• Lip Sync
The video and audio are synchronized in the monitor by
detecting the delay of monitored video automatically.
• Audio Return Channel
Audio Return Channel will reduce the number of cables
required to deliver audio upstream for processing and
playback.
In cases where HDTVs are directly receiving audio and video
content, this new Audio Return Channel allows the HDTV to
send the audio stream to the A/V receiver over the HDMI cable,
eliminating the need for an extra cable.
"x.v.Color" and "x.v.Color" logo are trademarks of Sony Corporation.
English
B60-5827-08_00_En.indd 57
57
10.8.3 11:08:45 AM
Specifications
AUDIO section
HDMI section
[RV-7000/RV-6000]
Rated output power during STEREO operation
(63 Hz – 20 kHz, 0.7% T.H.D., at 6 Ω) .......................... 100 W + 100 W
Effective power output during SURROUND operation
FRONT
(1 kHz, 10 % T.H.D. at 6 Ω) .........................................................150 W/ch
CENTER
(1 kHz, 10 % T.H.D. at 6 Ω) ............................................................. 150 W
SURROUND
(1 kHz, 10 % T.H.D. at 6 Ω) ........................................................150 W/ch
SURROUND BACK/SUBWOOFER (RV-6000 only)
(1 kHz, 10 % T.H.D. at 6 Ω) .............................................................. 150 W
HDMI input terminal ........................ HDMI 1, HDMI 2, HDMI 3, HDMI 4
HDMI output terminal ............................................................. MONITOR
[RA-5000]
Rated output power during STEREO operation
(63 Hz – 20 kHz, 0.7% T.H.D., at 6 Ω) .......................... 100 W + 100 W
Effective output power during STEREO operation
RMS (1 kHz, 10% T.H.D., at 6 Ω) .................................. 120 W + 120 W
Total harmonic distortion
......................................................................0.01 % (1 kHz, 50 W, 6 Ω)
Frequency response (IHF’66)
DVD, CD, AUX, VIDEO .......................10 Hz – 70 kHz, +0 dB – –3.0 dB
Signal to noise ratio (IHF’66)
DVD, CD, AUX, VIDEO ............................................................... 100 dB
Input sensitivity / impedance
DVD, CD, AUX, VIDEO ................................................. 500 mV / 47 kΩ
AV AUX ........................................................................ 500 mV / 26 kΩ
Output level / impedance
PRE OUT
(SUBWOOFER) ...............................................................2.0 V / 100 kΩ
(SURROUND BACK/FRONT HEIGHT : RV-7000 only) ...1.1 V / 100 kΩ
(SURROUND BACK : RV-6000 only) ..............................1.1 V / 100 kΩ
Tone control
BASS ....................................................................... ±10 dB (at 100 Hz)
TREBLE ................................................................... ±10 dB (at 10 kHz)
FM tuner section
Tuning frequency range......................................87.5 MHz – 108.0 MHz
AM tuner section
Tuning frequency range......................................... 531 kHz – 1,602 kHz
General
Power consumption
.....................................................................................................200 W
Standby power consumption (HDMI Link :Off) .............less than 0.5 W
Dimensions
[RV-7000/RA-5000]
........................................................................ W: 430 mm (16-14/16")
............................................................................... H: 159 mm (6-1/4")
............................................................................. D: 384 mm (15-1/8")
[RV-6000]
........................................................................ W: 430 mm (16-14/16")
............................................................................... H: 159 mm (6-1/4")
.........................................................................D: 373 mm (14-11/16")
Weight (net)
RV-7000/RV-6000 ........................................................ 9.0 kg (19.8 lb)
RA-5000 ....................................................................... 8.3 kg (18.3 lb)
• Kenwood follows a policy of continuous advancements
in development. For this reason specifications may be
changed without notice.
• The full performance may not be exhibited in an
extremely cold location (under a water-freezing
temperature).
DIGITAL AUDIO section
Input terminal
Optical..................................................................................CD, VIDEO
Coaxial .......................................................................................... DVD
VIDEO section
VIDEO input sensitivity / impedance (DVD, VIDEO, AV AUX)
Composite....................................................................... 1 Vp-p / 75 Ω
VIDEO output level / impedance (MONITOR)
Composite....................................................................... 1 Vp-p / 75 Ω
58
RV-7000/RV-6000/RA-5000
B60-5827-08_00_En.indd 58
10.8.3 11:08:45 AM
English
B60-5827-08_00_En.indd 59
59
10.8.3 11:08:45 AM
For your records
Record the serial number, found on the back of the unit, in the spaces
designated on the warranty card, and in the space provided below.
Refer to the model and serial numbers whenever you call upon your
dealer for information or service on this product.
Model
B60-5827-08_00_En.indd 60
Serial Number
10.8.3 11:08:45 AM