PARTS & ASSEMBLY SHEET
Fixture Name:
Joia 1993-5 PS
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Canopy
Wire Connectors
Top Loop
1ea
3ea
1ea
D150*H34mm
A4 Orange
Chain
Junction Box
Screw
Spring Washer
1ea
2ea
1ea
6ft x3.8mm
8/32" x 1"
@15 x 2mm
Chain Connector
Canopy Loop
with Collar
Nipple
2ea
1ea
1ea
@4.2X50mm
Mounting Strap
w/ ground screw
1ea
3/4"X4"
Part Needed
Part Needed
Reason why
Comments
@3/8 x 40mm x 5mm
@3/8 x 455mm
Hex Nut
2ea
@3/8 x 3mm
( missing, scratched, broken glass, bent, bad finish)
Quantity
Quantity
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1993-5 PS
Fig. 1
Note: The wire cage and fabric shade are
already assembled on the fixture body
1. Thread the nipple (N) into the coupling of
fixture body (O).
2. Place the top cap (M) over the nipple (N)
and secure it by threading the Top loop (J) on
until snug..
For Customer Service, contact the place of purchase to arrange for replacement parts.
PARTS & ASSEMBLY SHEET
Fixture Name:
Joia 1993-5 PS
ASSEMBLING THE FIXTURE (Fig. 2)
Fig. 2
3. By measuring determine correct number of
links needed for proper hanging height. Use a
pair of pliers to open one link of the Chain (K)
then remove the excess Chain (K) and discard it.
4. Use one chain connector (L) to attach one end
of the chain to the Top loop (J) and close the
chain connector.
5. Feed the fixture wires through the Chain (every
three links) and pull the wires until taut.
D
C
6. Slip Canopy loop collar (H) over the chain,
then do the same with the canopy (G).
7.7.Slip
Canopy
loop
(H) over
chain, then
do the
When
ready
tocollar
complete
thethe
installation
Use
same
with
the
canopy
(G).
the other chain connector and attach the other
end of the chain to the canopy loop (F) and close
8.the
When
ready
to complete the installation Use the other
chain
connector.
chain connector and attach the other end of the chain to
the
loop the
(F) and
close
connector.
8. canopy
Make sure
weight
ofthe
thechain
chandelier
will be
supported by the chain-not the electrical wire.
9. Make sure the weight of the chandelier will be supported
by the
chain-not
the electrical
wire.
* You
may now
install the
fixture.
Note: Complete these remaining steps after the
* You is
may
now install the fixture.
fixture
hung.
9. Install the light bulbs (not provided) in
accordance with the fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
INSTALLATION INSTRUCTIONS
Fixture Name:
Joia 1993-5 /-9 /- M1L PS
For Pendant Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
HANGING
THE FIXTURE (Fig. 1)
Fig. 1
1.1.Carefully
thenew
newfixture
fixture
from
carton
the yellow
Carefully remove
remove the
from
thethe
carton
and and
the yellow
bag
bag that holds all parts. Check that all parts are included as shown
that holds all parts. Check that all parts are included as shown in the
in the illustration and parts list.
illustration and parts list.
JUNCTION BOX
(CEILING)
2. Shut off the power at the circuit breaker and remove old fixture
2. Shut
off the
power atthe
the old
circuit
breaker strap.
and remove old fixture from
from
ceiling,
including
mounting
ceiling, including the old mounting strap.
A
B
3. Thread Nipple(C) into Canopy Loop (F) until snug.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached
4. Thread other end of the Nipple (C) with Canopy Loop attached into
into Mounting Strap (D).
D
Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
5. Place Lock Washer (B) over end of Nipple (C) protruding through
through
Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
until
tight. Strap (D) and thread Hex Nuts (A) onto Nipple until tight.
Mounting
C
E
F
Takethis
this mounting
mounting strap
and
mount
to ceiling
junction box
6.6.Take
strapassembly
assembly
and
mount
to ceiling
junction
box
with
junction
box
Screws
(E).
Tighten
screw
securely
with junction box Screws (E). Tighten screw securely with screw
driver.
with screw driver.
G
Unscrew the
the Canopy
Canopy loop
)from
thethe
Canopy
loop.loop.
Take the
7.7.Unscrew
loopcollar(H
collar (H
)from
Canopy
canopy
pass and
over pass
the Canopy
loop.
approximatly
one half of the
Take
theand
canopy
over the
Canopy
loop. approximatly
one
half loop
of the
canopy
loop should
exteriorbethreads
should
exposed.
canopy
exterior
threads
exposed.
Adjustbe
until
desired
Adjust
until
desired
height
is
reached.
*the
Canopy
loop
collar
height is reached. *the Canopy loop collar should fit snugly on
the
should fit snugly on the Canopy loop after the canopy is installed.
Canopy loop after the canopy is installed. Remove Canopy and
Remove Canopy and Canopy lock collar.
H
CHAIN
L
J
Canopy lock collar.
8.8.Assemble
fixtureand
andhave
have
assistant
or secure
support
Assemble the
the fixture
anan
assistant
or secure
support
hold
hold
the
weight
of
the
fixture
while
you
complete
the
wiring
the weight of the fixture while you complete the wiring connections.
connections.
9. Thread the fixture wires and ground wire of the assembled fixture
andand
nipple
and into
box.
9.through
Threadthe
thecanopy
fixtureloop
wires
ground
wiretheofoutlet
the assembled
fixture through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES
(Fig 2)
Fig. 2
CONNECTING
THEsupply
WIRES
(Fig.
2) lead wires by
10. Attach the power
wires to
the fixture
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or
connecting
BLACK to BLACK (or SMOOTH) and WHITE to
RIBBED).
WHITE
(or RIBBED).
HOUSE WIRES
BLACK
FIXTURE WIRES
WHITE
11. Attach the GROUND wire(GREEN or COPPER) from the Junction
11. Attach the GROUND wire(GREEN or COPPER) from the
Box and Box
the fixture
Ground
wire
to the green
Ground
Screw
on the
Junction
and the
fixture
Ground
wire to
the green
Ground
Screw
on
the
Mounting
Bracket
(D)
or
connect
both
wires
Mounting Bracket (D) or connect both wires together using the correct
together using the correct size of wire connectors.
size of Twist
wire connectors.
NOTE:
the wires together in the same direction you twist
the
wire
connector
onto
the wires.
NOTE: Twist the wires
together
in the same direction you twist the wire
SMOOTH (BLACK)
GREEN
(Ground)
RIBBED (WHITE)
BARE COPPER
(Ground)
connector
onto wire
the wires.
12.
Tuck these
connections neatly into the Junction Box.
12. Tuck these wire connections neatly into the Junction Box.
13. Raise Canopy (G) to the ceiling and secure in place by
13. Raise the
Canopy
(G) toloop
the ceiling
and into
secure
place byLoop(F).
tightening
tightening
Canopy
collar (H)
theinCanopy
the Canopy loop collar(H) into the Canopy Loop(F)
14. Install the light bulbs and shade as per the fixture assembly
14. Install the light bulbs and glass shade as per the fixture assembly
sheet.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.