Moxa CBL-RJ45M25-150 networking cable

CN2510 Series Quick Installation Guide
LED
Color
Reset
None
Second Edition, August 2004
1. Overview
Welcome to Moxa CN2510 Async Server, a communication server with 8/16
asynchronous RS-232 ports and 10/100 Mbps Ethernet LAN port. CN2510
Async Server can be used to connect terminals, modems, printers, and other
asynchronous serial devices to LAN hosts. CN2510 complies with TCP/IP
and IEEE 802.3 specifications using standard Ethernet 10/100BaseT and
twisted pair 10/100BaseTX cable as the physical medium.
Ready
Ready
Serial Tx
Serial Rx
Red
Green
Green
Yellow
Description
If you forget the password, use a pointed object,
such as a straightened paper clip or toothpick, to
press the reset button. The Ready LED will blink on
and off while the factory default settings are being
loaded. Once the Ready LED stops blinking (after
about 5 seconds), release the reset button. You will
hear a beep, which indicates that the default settings
have been restored, and CN2510 has rebooted.
Power is on and CN2510 is booting up.
Power is on and CN2510 is ready.
Serial port is transmitting data.
Serial port is receiving data.
Button
MENU
SEL
Name
menu
Action
activates the main menu, or returns to an upper level
scrolls up through a list of items shown on the LCM
up cursor
panel’s second line
down scrolls down through a list of items shown on the LCM
cursor panel’s second line
select selects the option listed on the LCM panel’s second line
The buttons are manipulated in a manner similar to the way a modern cellular
phone operates. As you move through the various functions and setting
options, note that the top line shows the current menu or submenu name, and
the bottom line shows the submenu name or menu item which is activated by
pressing the SEL button.
Refer to the CN2510 Async Server User’s Manual for more details.
Rear Panel
4. Hardware Installation
1.
2. Package Checklist
CN2510 Async Server products are shipped with the following items:
y 1 CN2510 Async Server
y 1 AC power Cord (only for CN2510-16 or CN2510-8)
y 1 Software and Documentation CD-ROM
y Quick Installation Guide
AC Power
Input
Power On/Off
Switch
RS-232
Console Port
LAN
Serial Ports
y 1 RJ45 Loopback Tester
y Product Warranty Booklet
y Rackmount kit including 2 brackets and 8 screws
y 1 CBL-RJ45F9-150
y 1 CBL-RJ45M25-150
Optional Accessories
y CBL-RJ45M9-150
y CBL-RJ45F9-150
y CBL-RJ45M25-150
y CBL-RJ45F25-150
Connector
Function
Automatic detection of 100-240V, 47-63Hz AC power
supply (CN2510-16 or CN2510-8).
NOTE: Notify your sales representative if any of the above items is missing or
damaged.
Front Panel
B.
I indicates power on; O indicates power off
One RJ45 connector for console terminal connection
Auto detecting 10/100 Mbps port
8 or 16 RJ45 connectors for DCE (modem) connections
We recommend using the LCM display and four push buttons to configure
the IP address for the first time.
Basic Operation:
If the CN2510 is working properly, the LCM panel will display a green color.
The red Ready LED will also light up, indicating that the CN2510 is
receiving power. After the red Ready LED turns to green, you will see a
display similar to:
C N 2 5 1 0
1 6 _ 3
1
9 2
.
1 6 8
.
1 2 7
.
2 5 4
CN2510-16
3
192.168.127.254
3. Hardware Introduction
Wiring Requirements
A.
Automatic detection of 12-48VDC, 1.01A at 12V, 240 mA at
48V DC power supply (CN2510-16-48V or CN2510-8-48V)
LCM Display
8-pin RJ45 to Male DB9 cable, 150 cm
8-pin RJ45 to Female DB9 cable, 150 cm
8-pin RJ45 to Male DB25 cable, 150 cm
8-pin RJ45 to Female DB25 cable, 150 cm
2.
Installing CN2510
Open the package, and place CN2510 on a desktop, or attach it to a
standard rack cabinet.
is the CN2510’s name
is the CN2510’s serial number
is the CN2510’s IP address
There are four push buttons on CN2510’s nameplate. Going from left to right,
the buttons are:
C.
3.
Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE: Do not run signal or communication wiring and power
wiring in the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
Where necessary, it is strongly advised that you label wiring to all
devices in the system.
Connecting the Power
AC: Connect CN2510 100-240 VAC power line with its AC connector. If
the power is properly connected, the “Ready” LED will show a solid
red color until the system is ready, at which time the “Ready” LED
will change to a green color.
DC: Connect CN2510-16/8-48V’s power cord to CN2510’s DC
connector, and then follow the steps given below:
ON
V+ V-
OFF
1. Loosen the screws on the V+ and V- terminals of
CN2510-8/16-48V’s terminal block.
2. Connect the power cord’s 48 VDC wire to the
terminal block’s V+ terminal, and the power cord’s
DC Power Ground wire to the terminal block’s Vterminal, and then tighten the terminal block screws.
(Note: CN2510-8/16-48V can still operate even if the
DC 48V and DC Power Ground are reversed.)
If the power is properly connected, the “Ready” LED will show a solid red
color until the system is ready, at which time the “Ready” LED will
change to a green color.
P/N: 18020251001
— 1 —
— 2 —
— 3 —
Grounding CN2510-16/8-48V:
Grounding and wire routing helps limit the effects of noise
ON
OFF
due to electromagnetic interference (EMI). Run the ground
connection from the ground screw to the grounding
surface prior to connecting devices. The Shielded Ground
V+ V(sometimes called Protected Ground) contact is the second
contact from the right of the 5-pin power terminal block
SG
connector located on the rear panel of CN2510-8/16-48V.
Connect the SG wire to the Earth ground.
6. Pin Assignments and Cable Wiring
10/100BaseTX
Port Pinouts
Console Port Pinouts
Async RS-232 Port Pinouts
4.
LAN
LAN
6.
DB9 Female Connector
DB25 Male Connector
DB25 Female Connector
Connecting to the Network
Connect one end of the Ethernet cable to CN2510’s 10/100M Ethernet
port and the other end of the cable to the Ethernet network. There are 2
LED indicators located on the top left and right corners of the Ethernet
connector. If the cable is properly connected, CN2510 will indicate a valid
connection to the Ethernet in the following ways:
5.
DB9 Male Connector
10/100BaseTX Cable Wiring
The top right corner LED indicator maintains a solid
green color when the cable is properly connected to a
100 Mbps Ethernet network.
The top left corner LED indicator maintains a solid
orange color when the cable is properly connected to
a 10 Mbps Ethernet network.
Connecting to a Serial Device
Connect the serial data cable between CN2510 and the serial device.
7. Environmental Specifications
Async RS-232 Cable Wiring:
Note: The following cables are optional accessories.
CBL-RJ45M9-150
Connecting to a Console
CBL-RJ45F9-150
A console is a combination of keyboard and monitor that are used to
configure settings and to monitor the status of your system. If you do not
have a network environment, use a terminal, a PC running UNIX, or a PC
with terminal emulation software (e.g., HyperTerminal in Windows;
PComm by Moxa). Use an RJ45-to-DB25 or RJ45-to-DB9 cable to
connect the terminal to the console socket. Refer to the CN2510 Async
Server User’s Manual for more details.
CBL-RJ45F25-150
CBL-RJ45M25-150
5. Software Installation
Power requirements
Power Input
Power Consumption
CN2510-8/16
CN2510-8/16-48V
Operating temp.
Operating humidity
Dimensions (W×D×H)
Serial line protection
Magnetic isolation
Power line protection
Regulatory approvals
100 to 240 VAC, 47 to 63 Hz, or 12-48 VDC
235 mA for 100V, 145 mA for 240V
250 mA (at 48V max.)
0 to 55°C (32 to 131°F)
5 to 95% RH
190 × 44.5 × 478 mm (including ears)
190 × 44.5 × 440 mm (without ears)
15 KV ESD for all signals
1.5 KV for Ethernet
4 KV Burst (EFT), EN61000-4-4
2 KV Surge, EN61000-4-5
FCC Class A, CE Class A, UL, CUL, TÜV
Entering the Console Utility
The Console Utility is the main application needed to set up the server/port
configuration, and to execute utilities such as ping, diagnosis, monitor, and
upgrade. There are two ways to enter the Console Utility. One is to use
terminal emulation through a console terminal, and the other is to telnet from
a network terminal.
Copyright  2004
Moxa Technologies Co., Ltd.
All rights reserved.
Reproduction without permission is prohibited.
Refer to the CN2510 Async Server User’s Manual for more details.
DB9 and DB25 connector pinouts:
The following figures illustrate standard connector pinouts. However, pinouts
for serial devices differ from manufacturer to manufacturer. Refer to the
serial device’s user’s manual for the exact pinouts of your device.
— 4 —
— 5 —
Tel:
+886-2-8919-1230
Fax: +886-2-8919-1231
www.moxa.com
support@moxa.com.tw
— 6 —