POE-SW1602/POE-SW2402 User Manual

POE-SW1602/POE-SW2402
User Manual
User manual of POE-SW1602/POE-SW2402
User Manual
About this Manual
This Manual is applicable to POE-SW1602/POE-SW2402.
The Manual includes instructions for using and managing the product. Pictures, charts, images and all other
information hereinafter are for description and explanation only. The information contained in the Manual is
subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the
company website
Please use this user manual under the guidance of professionals.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE,
SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND OUR COMPANY MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY
QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL
OUR COMPANY, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH
THE USE OF THIS PRODUCT, EVEN IF OUR COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN
RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE
OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER
INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION
BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. OUR
COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
1
User manual of POE-SW1602/POE-SW2402
Regulatory Information
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a
shielded RJ45 cable.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a
shielded RJ45 cable.
IC
CAN ICES-3(A)/NMB-3(A)
2
User manual of POE-SW1602/POE-SW2402
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property
loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings Follow these safeguards to prevent
Cautions Follow these precautions to
serious injury or death.
prevent potential injury or material
damage.
Warnings
●
Proper configuration of all passwords and other security settings is the responsibility of the installer and/or
end-user.
●
In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation
and region. Please refer to technical specifications for detailed information.
●
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with
100~240 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for
detailed information.
●
Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire
hazard.
●
Please make sure that the plug is firmly connected to the power socket.
●
If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then
please contact the service center.
3
User manual of POE-SW1602/POE-SW2402
Preventive and Cautionary Tips
Before connecting and operating your device, please be advised of the following tips:
•
•
•
•
•
Ensure unit is installed in a well-ventilated, dust-free environment.
Unit is designed for indoor use only.
Keep all liquids away from the device.
Ensure environmental conditions meet factory specifications.
Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it
may cause damage to the sensitive electronics within the unit.
•
•
•
•
Use the device in conjunction with an UPS if possible.
Power down the unit before connecting and disconnecting accessories and peripherals.
A factory recommended HDD should be used for this device.
Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used batteries according to the instructions provided by the battery
manufacturer.
4
User manual of POE-SW1602/POE-SW2402
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.
The figures in the manual are for reference only.
This manual is applicable to the models listed in the following table.
Model
POE-SW1602
POE-SW2402
5
User manual of POE-SW1602/POE-SW2402
TABLE OF CONTENTS
TABLE OF CONTENTS ............................................................................................................................ 6
Chapter 1
Product Overview .......................................................................................................... 7
1.1
Introduction ................................................................................................................................ 7
1.2
Package Contents ....................................................................................................................... 7
1.3
Front Panel ................................................................................................................................. 8
1.4
Rear Panel ................................................................................................................................ 10
Chapter 2
2.1
Device Installation ....................................................................................................... 11
Installation Notes ..................................................................................................................... 11
Safety Alert ...................................................................................................................................... 11
Environmental Requests .................................................................................................................. 11
Tools ................................................................................................................................................ 12
2.2
Installation................................................................................................................................ 12
Rack-mounting ................................................................................................................................ 12
Desktop-mounting ........................................................................................................................... 13
2.3
Grounding................................................................................................................................. 14
With grounding bar ......................................................................................................................... 14
Without grounding bar.................................................................................................................... 15
Chapter 3
Physical Connection ..................................................................................................... 17
3.1
Connect to RJ45 Ports ............................................................................................................... 17
3.2
Connect to SFP Combo ............................................................................................................. 17
3.3
Check the Cabling ..................................................................................................................... 18
3.4
Connect to Power Supply .......................................................................................................... 19
Appendix Technical Specifications .................................................................................................... 20
6
User manual of POE-SW1602/POE-SW2402
Chapter 1 Product Overview
1.1 Introduction
POE-SW1602/POE-SW2402 is a 16/24-Port 10/100Mbps + 2-Port Gigabit TP/SFP Combo Unmanaged PoE Switch. It
provides 16/24 10/100Mbps auto-negotiation RJ45 ports and 2 Gigabit TP/SFP combos.
POE-SW1602/POE-SW2402 (Ports 1-16/24) supports IEEE 802.3af PoE (15.4W) and IEEE 802.3at PoE+ (30W)
powering. The whole PoE output is 230W (POE-SW1602) and 370W (POE-SW2402). By using Cat 5 twisted pair,
the device can provide data and power for APs, IP cameras, IP phones, and other PoE devices. Moreover, with
using Cat 5e Ethernet cable and enabling extend mode, the transmission distance of data and power can be as
long as 250m.
1.2 Package Contents
Open your package and check the followings.
Item
Number
Switch
1
Power cord
1
Footpads
4
User Manual
1
Screws
8
L-shaped brackets
2
If any item is incorrect, missing, or damaged, please keep the original package and contact the vendor for
replacement immediately.
7
User manual of POE-SW1602/POE-SW2402
1.3 Front Panel
Figure 1.1 POE-SW1602
Figure 1.2 POE-SW2402
Table 1.1 Description of LEDs
LED
Status
Solid
Description
The device is connected to the power supply properly.
PWR
Off
Solid
LINK/ACT
Blinking
Off
Solid
POE STATUS
Blinking
Off
Solid
POE-MAX
Blinking
Off
Solid
G1/G2
Blinking
Off
Solid
The device is connected improperly or not connected to the power supply.
The corresponding port is connected properly.
The corresponding port is transmitting data.
The corresponding port is connected improperly or not connected.
The corresponding port is connected with a PD (Powered Device) and powers
the PD properly.
The PoE output of the corresponding port exceeds 30W.
The corresponding port is no PoE power output or no PD connected.
The PoE power gets to the alarm value, and the available PoE power is less
than 6W.
The PoE power gets to the maximum.
The PoE power works properly, and the available PoE power is more than 6W.
The corresponding port is connected.
The corresponding port is transmitting data…
The corresponding port is connected improperly or disconnected.
The corresponding port is connected properly.
G1-F/G2-F
Off
The corresponding port is connected improperly or not connected.
8
User manual of POE-SW1602/POE-SW2402
*If G-F port (G2-F/G2-F) is connected, LEDs of G (G1/G2) ports will not light.

Extend Mode
Details for enabling extend mode:
Status
Status
Description
Default
Ports 1-8: 100M
ON
Ports 1-8: 10M with Extend Mode being enabled
Default
Ports 9-16: 100M
ON
Ports 9-16: 10M with Extend Mode being enabled
EXTEND 17-24
Default
Ports 17-24: 100M
*Only for POE-SW2402
ON
Ports 17-24: 10M with Extend Mode being enabled
EXTEND 1-8
EXTEND 9-16
Cautions
1. To guarantee the extend mode performance, please use Cat 5e or better Ethernet cable and configure the
speed and duplex of the remote device to be “Auto Negotiation”.
2. If Extend mode is disabled, the transmission distance of PoE powering and data is up to 150m by using Cat 5e
or better Ethernet cable.

RJ45 ports & SFP combos
1000Mbps SFP combos
Model
10/100Mbps RJ45 ports
10/100/1000Mbps RJ45 ports
(G1-F/G2-F)
POE-SW1602
16
2
2
POE-SW2402
24
2
2
Note that:
1. Ports 1-8 are with high priority by default, which take advantage over other ports to process key data or video
data.
2. Ports 1-16/24 support IEEE 802.3af and IEEE 802.3at PoE power;
3. When SFP combos (G1-F/G2-F) and G1/G2 port are connected, SFP combos will get priority over G1/G2 to work.
4. Optional module is not included in the device packaging. Please prepare by yourself if needed.
9
User manual of POE-SW1602/POE-SW2402
1.4 Rear Panel
The rear panels of POE-SW1602/ POE-SW2402 are similar. Here take POE-SW2402 as a guide.
Figure 1.2 POE-SW2402

Power Socket
Used for connecting the included power cord for power supply. Please use the included power cord to connect
the device to power supply.

Grounding Terminal
Used for connecting the grounding cable for lightning-resisting. The grounding details refer to Section 2.3
Grounding
10
User manual of POE-SW1602/POE-SW2402
Chapter 2 Device Installation
(Here POE-SW2402 is taken as an installation guide, which applies to POE-SW1602.)
2.1 Installation Notes
To guarantee the device long service and your personal safety, please follow notes below.
Safety Alert

Wear antistatic gloves while installing, and connect the device to power after finishing other installation.

Use the included power cord to power the device.

Make sure the input voltage matches the value which is marked on the device's label.

Place the device in a well-ventilated and dry environment.

Do not open the cabinet of the device.

Disconnect the device from the power supply when you are to do the cleaning.

Position the device away from strong current.
Cautions
There is a seal covering one of the screws in the case of the device. In case of need repair, keep the seal unbroken
until the agent supervise the maintenance. The user should not break the seal of the coverage without permission
of the local agent, otherwise will be responsible for any damage.
Environmental Requests

Temperature/Humidity
Item

Temperature
Humidity
Operation Environment
0℃ - 40℃
10% - 90% RH (non-condensing)
Storage Environment
-40℃ -70℃
5% - 90% RH (non-condensing)
Antistatic Precautions
Dust may lead to electrostatic adsorption. To protect the device from static electricity harm, please pay attention
to the following:

Keep the device environment air clean. (A regular dusting is necessary)

Make sure the device is grounded well.
11
User manual of POE-SW1602/POE-SW2402

Lightning Protection
In a thunderstorm weather, a sudden current may damage the device. To protect the device from lightning stroke
or strong current, please:

Make sure the device, the installation desktop/rack and power outlet on the wall all are well-grounded.

Cable the device properly; and if you need to cable outdoors, it is advisable to set up with a signal lightning
arrester.

Mounting Standards
No matter whether it is rack-mounting or desktop-mounting, follow the instructions below.

The rack/desktop is stable and sturdy enough.

Place the device in a clean, dry and well-ventilated environment. Keep at least 10cm free on all sides for
cooling.

Do not place any heavy or big size object on the device.

Keep at least 1.5cm vertical distance between each device while installing it in stack.
Tools
Things you'll need but should be prepared by yourself.
Figure 2.1 Installation Tools
2.2 Installation
The device supports two types of installation: rack-mounting and desktop-mounting. Install your device according
to the tools you have.
Rack-mounting
You can install the device in a standard 19-inch rack with the accessories (L-shaped brackets and screws) come
with the box.
12
User manual of POE-SW1602/POE-SW2402
1) Fix the rack on the ground, stable and level; and ground the device well.
2) Fix L-shaped brackets to the device with screws. (Shown as below)
Figure 2.2 L-shaped bracket installation
3) Adjust the device to a nice height and fix the device to the rack with screws (self-prepared). (Shown as below)
Figure 2.3 Fix to the rack
Desktop-mounting
Also, you can install the device on a desktop.
1) Place the device bottom up on a stable and flat desktop.
2) Paste the four footpad stickers to the corresponding four corners of the device bottom.
13
User manual of POE-SW1602/POE-SW2402
Figure 2.4 Paste the footpads
3) Then place the device correctly on the desktop.
2.3 Grounding
Grounding is not only important for lightning arresting and anti-interference, but for your own personal safety.
Please select the proper method to ground your device.
With grounding bar
If a grounding bar is available at the installation site, follow either of the two installations to ground the device.
A. Connect to the Grounding Bar Directly
1) Connect one end of the grounding cable to the binding post on the grounding bar.
2) Connect the other end of the grounding cable to the grounding terminal and fix the screw.
Figure 2.5 Connect to the grounding bar
B. Connect to another grounded device
1) Connect one end of the grounding cable to the grounding terminal of the grounded device and fix the screw.
14
User manual of POE-SW1602/POE-SW2402
2) Connect to the other end of the grounding cable to the grounding terminal of the device and fix the screw.
Figure 2.6 Connect to a grounded device
Cautions
Connect the grounding cable to the earthing system in the equipment room. Do not connect it to a fire main or
lightning.
Without grounding bar

If there is no ground bar but earth nearby and the grounding body is allowed to be buried, follow below
steps:
1) Bury an angle steel or steel pipe (≥0.5m) into the mud land.
2) Weld one end of the grounding cable to the angle steel or steel pipe and embalm the welding point.
3) Connect the other end of the grounding cable to the grounding terminal and fix the screw.
15
User manual of POE-SW1602/POE-SW2402
Figure 2.7 Ground with an angle steel

If both ground bar and the conditions for burying the grounding body are not available, an AC-powered
Ethernet switch can be grounded using the PE (Protecting Earth) wire of the AC power supply.
Figure 2.8 Ground with 3-core AC power cord
Cautions
Make sure that the PE wire of the AC power supply has been well grounded at the side of the power distribution
room or AC power supply transformer.
16
User manual of POE-SW1602/POE-SW2402
Chapter 3 Physical Connection
3.1 Connect to RJ45 Ports
Connect the switch to a remote device with Ethernet cable via RJ45 port. G1 and G2 are uplink ports. Ports
1-16/24 support IEEE 802.3af and IEEE 802.3at PoE supply, and the PD can be wireless AP, IP phone or IP camera,
etc. By default, PoE features of Ports 1-16/24 are enabled.
Figure 3.1 RJ45 port connection
Note that:
1.
Cat 5e or better Ethernet cable is recommended. As each RJ45 port supports MDI/MDIX auto-negotiating,
either parallel or crossover cable is available.
2.
The device supports dynamic PoE supply. Namely, the device will power the PD properly and automatically.
3.2 Connect to SFP Combo
1) Insert your optical module into the SFP port (G1-F/G2-F).
17
User manual of POE-SW1602/POE-SW2402
Figure 3.2 Insert optical module
2) Insert the remote optical fiber to the module correctly. (RX fiber into the port labeled RX on the module; and
TX fiber into the TX)
Figure 3.3 Insert optical fiber
3.3 Check the Cabling
Once installation is completed, check the cabling of the device as the following:

The operating power supply should accord with rated input standard.

Ports cablings and grounding cable are correctly connected.

If there is outdoor cabling, connect a lightning protector to the cable before you plug the cable into the
18
User manual of POE-SW1602/POE-SW2402
port.
Figure 3.4 Lightning protector connection
① Ethernet cable
③ Grounding terminal
② Grounding cable
④ Outdoor cabling
⑤ Lightning protector
3.4 Connect to Power Supply
Please use the included power cord for power supply.
Figure 3.5 Power connection
19
User manual of POE-SW1602/POE-SW2402
Appendix Technical Specifications
Interfaces
Performance
Item
POE-SW2402
POE-SW1602
10/100Mbps RJ45
24
16
10/100/1000Mbps RJ45
2 (G1, G2)
2 (G1, G2)
1000Mbps SFP
2 (G1-F, G2-F)
2 (G1-F, G2-F)
High priority ports
1-8
1-8
Store-and-forward
Supported
MAC Table
4k
MAC Learning
Auto-learning/ Auto-aging
Switching Capacity
8.8Gbps
PoE standard
IEEE 802.3af, IEEE 802.3at
PoE Powering Mode
PoE Power
4k
7.2Gbps
Supports 8 pins powering, which means pins 1,2,3,6 and pins
4,5,7,8 can power simultaneously
PoE Port
1-24
1-16
Max Port Output
30W
30W
Max Total Output
370W
230W
Extend Mode
Supported
RJ45 port
Lightning-proof
lightning proof
Ranking
Power source
lightning proof
Power Input
Physical Environment
4KV
6KV
100-240V AC, 50/60Hz
Operating
Temperature: 0℃-40℃
Environment
Humidity: 10%-90% RH non-condensing
Storage
Temperature: -40℃-70℃
Environment
Humidity: 5%-90% RH non-condensing
Ethernet: 10Mbps (Half Duplex) / 20Mbps (Full Duplex)
Transmission Speed
Fast Ethernet: 100Mbps (Half Duplex) / 200Mbps (Full Duplex)
Gigabit Ethernet: 2000Mbps (Full Duplex)
Ethernet: Cat 3 or better UTP/STP
Fast Ethernet: Cat 5 or better UTP/STP
Transmission Medium
Gigabit Ethernet: Recommended to use Cat 5e or Cat 6 UTP/STP
1000Base-SX: MMF (Multimode optical fiber)
1000Base-LX: MMF (Multimode optical fiber) or SMF (Single
Mode Fiber)
Network Standard
IEEE 802.3, IEEE 802.3u, IEEE802.3ab, IEEE 802.3af, IEEE802.3at,
IEEE 802.3x, IEEE802.3z
20