Cordless Screwdriver

WD040110036

3.6V

WD040110036

Thank you for purchasing a WIDO product. We are confident that you will appreciate the quality of the product and you will be entirely satisfied with your purchase. Please read carefully the user safety and operating instruction on how to operate this product correctly within safety norms and regulations.

2

1

WD040110036

2 3 4

5

9

1 1

8 7

1 0

6

3

1

4

7

2

WD040110036

3

5 6

4

3.6V CORDLESS SCREWDRIVER ENG

COMPONENT LIST

1) Bit holder

2) Pivoting handle release button

3) Charging indicator

4) Charger jack

5) Forward and reverse rotation control lever & trigger lock

6) Rotating handle

7) On/Off switch

8) Light switch

9) Work light

10) Charger

11) Charger plug

NORMAL ACCESSORIES

1) Battery charger: 110-120V or 220-240V~50 -60Hz 1pc

2) Screwdriver bits: 4pcs

We recommend that you purchase your accessories from the same store that sold you the tool.

Use good quality accessories marked with a well-known brand name. Choose the type according to the work you intend to undertake. Refer to the accessory packaging for further details. Store personnel can assist you and offer advice.

5

3.6V CORDLESS SCREWDRIVER ENG

GENERAL POWER TOOL SAFETY WARNINGS

Warning: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2) Electrical safety a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool.

Do not use a power tool while you are tired or under the influence of drugs, alcohol or

medication. A moment of inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

6

3.6V CORDLESS SCREWDRIVER ENG

e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with

the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

5) Battery tool use and care

a) Ensure the switch is in the off position before inserting battery pack. Inserting the battery pack into power tools that have the switch on may be invites accidents.

b) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

c) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

d) When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal

to another. Shorting the battery terminals together may cause burns or a fire.

e) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or burns.

6) Service a) Have your power tool serviced by a qualified repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

7

3.6V CORDLESS SCREWDRIVER ENG

ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR POWER TOOL

1) Hold power tools by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring. Contact with a “live” wire will make exposed metal parts of the tool

“live” and shock the operator.

2) Do not drive screws into existing walls or other blind areas where electrical wiring may exist. If this

situation is unavoidable, remove all fuses or disconnect all breakers feeding the work area.

3) Never hold the body of the cordless screwdriver near the switch while changing screwdriver bits.

Accidentally touching the switch may start the power tool and possibly cause an injury.

4) Always use the correct shape and size of screwdriver bit that matches the head of the screw.

5) Do not use worn or damaged screwdriver bits. Worn or damaged screwdriver bits will not drive the screw properly and may jump out of the screw head, causing possible injury.

6) Use clamps or another practical way to secure and support the work piece to a stable platform.

Never hold in hand or across legs. The rotating action of the screwdriver may cause the bit to come loose from the screw and cause injury.

ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR CHARGER AND BATTERY

1) Charger is for indoor use only. Do not expose charger to rain or snow. Do not recharge battery in damp or wet environment.

2) Use only the supplied charger when charging your power tool. The use of any other charger could damage the power tool or create a hazardous condition.

3) Always charge the battery pack between temperatures 0°C to 40°C (32°–104° F).

4) Before using charger, be sure the supply is the same as the voltage given on the nameplate of the charger.

5) To unplug charger from outlet when you do not use the charger.

6) To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.

7) If the charger supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

8) Do not incinerate the battery even if they are severely damaged or completely worn out. The battery can explode in a fire.

8

SYMBOLS

To reduce the risk of injury, user must read instruction manual

Warning

Wear eye protection

Wear dust mask

Wear ear protection

Indoor use only

3-5 hour charging time

Always charge the battery pack between temperatures 0

0

C to 40

0

C

Do not expose to rain or water

Do not burn

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice

TECHNICAL DATA

Model

Voltage

Battery

Max. screw

No load speed

Max. Torque

Chuck size

Machine weight

3.6V D.C.

Ni-Cd

ST4X40mm

220/min

3.5N.m

1/4” hex

0.70kg

WD040110036

3.6V D.C.

Ni-Cd

ST4X40mm

220/min

3.5N.m

6.35mm hex

0.70kg

Battery charger

Input

Output

Charger time

110-120V~50-60Hz

6V D.C.

3-5 hour (approx)

220-240V~50-60Hz

6V D.C.

3-5 hour (approx)

9

3.6V CORDLESS SCREWDRIVER ENG

OPERATING INSTRUCTIONS

Note: Before using the tool, read the instruction manual carefully.

1. Intended use

The machine is intended for driving in and loosening screws.

2. Before using your tool

Your battery in power tool is uncharged and you must charge once before use. When you charge the new battery or one which has not been used for long periods of time, your battery may not be fully charged until you have performed several charge and discharge operations by charging & working with your power tool. After this your battery performance will improve.

Warning: The charger and battery are specifically designed to work together so do not attempt to use any other devices.

3. Battery charging

1) Be sure the supply is the same as the voltage given on the nameplate of the battery charger.

Connect battery charger plug into the charger jack on the handle of the power tool, then connect battery charger to power source, and charging indicator on handle of the power tool is illuminated in red color, charging has started (See Fig 1).

2) After charging 3-5 hours, unplug the charger from the power source and remove the charger plug from the charger jack on handle of the power tool.

Note: A new battery or one that is completely exhausted should be charged for five hours. After normal use, the battery should be fully charged in about three hours.

Warning: Do not operate power tool or charger near flammable liquids or in gaseous or explosive atmospheres. Internal sparks can ignite fumes.

4. Reversing the rotational direction

press the forward and reverse rotation control lever from the “ ”side for clockwise rotation or from the “ ” side for anticlockwise rotation (See Fig 2).

2) When the forward and reverse rotation control lever is in the neutral position, the switch trigger cannot be pulled.

Note:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the power tool comes to a complete stop. Changing the direction of rotation before the power tool stops may damage the tool.

• When not operating the power tool, always set the rotation control lever to the neutral position.

5. Switching on and off

To start your power tool, simply press the switch trigger and keep it pressed. To switch off the machine,

10

3.6V CORDLESS SCREWDRIVER ENG release the switch trigger (See Fig 3).

6. Work light

The screwdriver has a built-in LED work light. This feature is convenient when working in close or tight areas where additional light is needed.

To turn the work light on, press the light switch once. To turn the switch off, press the light switch a second time (See Fig 4).

Note: Make sure you turn the light switch off when the work light is not in use to prevent the battery from being run down.

7. Pivoting handle

To change the pivoting handle to the "in line" position, press and hold the pivoting handle release button and rotate handle clockwise. Release the button and continue to rotate the handle 180° (See Fig

5). The release button will lock the handle in the "in line" position when the handle is fully rotated 180°.

Reverse these actions to return the handle to the pistol grip configuration.

8. Installing and removing bit

Move forward and reverse rotation control lever to the neutral position. Select an appropriate screwdriver bit that fits the head of the screw being driven. To install a bit simply insert it into the cavity in the bit holder. To remove bit, pull straight out (See Fig. 6).

Note: Make sure the screwdriver bit is in good condition and is neither damaged nor worn.

9. Screw driving operation

When driving screws, care must be taken to use the bit that correctly fits the head of the screw being driven. Make sure to use the largest bit size that will properly fit into the head of the screw. The bit must also be in good condition and not worn so it will drive screws without slipping out of the screw head.

1) Select the correct screwdriver bit for the screw being driven.

2) Insert the bit fully into the bit holder.

3) Set the rotation direction switch so the screwdriver bit is turning clockwise.

4) Insert the screwdriver bit fully into the screw head.

5) While holding the screwdriver firmly against the screw and the bit aligned with the screw, press the trigger switch to start the screwdriver and drive the screw (See Fig. 7).

6) When the screw is driven to the correct depth, release the switch. The screwdriver will stop.

7) When the switch is released and the screwdriver stops turning, the spindle will automatically lock.

Fully tighten the screw by manually rotating the screwdriver handle in a clockwise direction.

8) To remove screws, follow the same general procedure as for driving screws.

Note: Make sure that the driver bit is inserted straight in the screw head, or the screw and /or bit may be damaged.

WORKING HINTS FOR YOUR POWER TOOL

1. Always use the correct type of screwdriver bit.

2. Always hold the power tool and screwdriver bit in a straight line with the screw.

3. If screws are difficult to tighten, try applying a small amount of washing liquid or soap as a lubricant.

4. Before screwing larger, longer screws into hard materials, it is advisable to predrill a pilot hole with

11

3.6V CORDLESS SCREWDRIVER ENG the core diameter of the thread to approx. 2/3 of the screw length.

MAINTENANCE

WARNING: Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.

1. Your power tool requires no additional lubrication or maintenance.

2. There are no user serviceable parts in your tool, battery pack or changer.

3. Never use water or chemical cleaners to clean your tool. Wipe clean with a dry cloth.

4. Always store your power tool in a dry place.

5. Charge the battery pack when you do not use it for more than six months.

TROUBLESHOOTING

1. If your power tool will not operate, charge your power tool.

2. If the power tool doesn’t work properly, check the screwdriver bit for sharpness, replace screwdriver bit if worn.

3. If a fault cannot be rectified, return the power tool to an authorized dealer for repair.

DISPOSAL OF AN EXHAUSTED BATTERY PACK

Cd

To preserve natural resources, please recycle or dispose of the battery pack properly. This battery pack contains nickel-cadmium batteries. Consult your local waste authority for information regarding available recycling and/or disposal options. Discharge your battery pack by operating your tool, then remove the battery pack from the tool housing and cover the battery pack connections with heavy duty adhesive tape to prevent short circuit and energy discharge. Do not attempt to open or remove any of the components.

ENVIRONMENT PROTECTION

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

12

3.6V CORDLESS SCREWDRIVER ENG

EXPLOSIVE VIEW

13

10

11

8

9

12

13

14

5

6

7

3

4

NO

1

2

15

16

3.6V CORDLESS SCREWDRIVER ENG

PART LIST

DESCRIPTION

Right housing

Right handle

Circlip

Bushing

Gear box

Locking ring

Bit holder

Pin

Driving block

Planetary gear

Fixed gear ring

Planetary carrier

Plastic planetary gear

Washer

Motor gear

Screw

3

1

6

1

1

3

1

1

1

1

Q’TY

1

1

1

1

1

2

24

25

26

27

28

29

30

21

22

23

NO

17

18

19

20

31

DESCRIPTION

Flange

Screw

Motor

Light switch

Rotation control lever

Spring

Switch assemble

Battery set

Trigger with screw

Left handle

Screw

Left housing

Release button

Spring

Cover

1

9

1

1

1

1

1

1

1

1

Q ’TY

1

3

1

1

1

14

WD040110036

15

MADE IN CHINA

Copyright @ WIDO Machinery Co., Ltd. All rights reserved.

www.widopt.com