Jaton WINCOMMV92-LX modems

WinCOMM V.92_LX
Internal 56Kbps Fax Data modem with Caller ID
Quick Start Guide
Version 1.0
FEATURES/SPECIFICATIONS
• V.90, V.92, ITU-T, V.34, V.32 bis, V.32, V.22 bis V.22 and Bell
212A, ITU-T, V.23, V.21 and Bell 103
•
•
•
•
•
•
•
Transmission speed – receiving rate up to 56Kbps (downstream), and
transmit rate up to 33.6 Kbps.
Data Compression – ITU-T V.44, V.42 bis and MNP5
Fax specs – ITU-T V.17, V.29, V.27 ter, V.21 channel 2
EIA/TIA 578 FAX Class 1, or T.31 Fax Class 1.0 commands
PCI 2.2-compliant
Full Duplex
Tone and Pulse dialing
Auto detect Voice/Data/Fax modes
SYSTEM REQUIREMENTS:
• x86 compatible PC with a PCI bus expansion slot
•
•
•
•
CD-ROM drive, Quad speed or
faster
Hard Drive with at least 100MB free space
Microsoft Windows® XP, Windows® Vista
Sound card required for Voice and Answering functions
CHECK LIST:
• Internal PCI Modem
•
•
•
RJ11 Phone Cord
Software & Document CD-ROM
Quick Start Guide (Printed)
2
Hardware Installation:
1.
2.
3.
4.
5.
Make sure the power to your PC is turned OFF.
Remove the computer’s cover.
Select a PCI bus expansion slot for the new adapter. Remove the slot
cover
Insert the modem into place carefully. Secure the adapter and
retaining bracket.
Replace the computer’s cover.
HARDWARE DESCRIPTION:
3
Software Installation:
This guide is intended to help you get started quickly with driver
installation in Microsoft Windows.
Important Notice: Add second modem or change the modem to an
existing PC system, you may proceed a few steps before install the new
hardware and software (modem’s driver). The followings are some of the
considers:
1.
To change a new modem, please remove the existing modem driver,
or disable it from Windows® system before you remove the existing
hardware.
2.
To added second modem, make sure the mainboard that has available
IRQ for new devices, and there is no conflict between the others.
3.
The driver installation for upgrade system as same as below, if error
occur when you proceed step 1, or 2, please consult with your system
dealer or the existing hardware manufacturer support.
á
Windows® XP/ Vista Installation
Windows® XP is the latest version out from Microsoft and that has built-in
PnP function to detects any new hardware (included this modem) on the
system but make sure your motherboard utility driver is installed correctly.
4
After your XP’s desktop loads-up completely, the new hardware wizard
will be prompt for your modem. If your windows system has trouble to
detect it, or your desktop problem to starts-up after modem added
physically, please re-start your windows system again, and make sure the
motherboard utility has been setup properly.
Insert the manufacturer’s software CD into your CD-ROM and follow the
steps to install the modem driver.
1.
For WinXP, once you have completed the hardware installation,
power on your computer. The Found New Hardware Wizard will
show a prompt to search for driver for new hardware found. Click
Cancel.
2.
After inserting the CD, click on Modem Driver.
3.
Select your system Operating System.
4.
For Vista system, need to click Allow.
5.
Click OK to continue with driver installation
FaxTalk Communication SE
Note:
FaxTalk may detect that your modem as supporting
speakerphone, and display speakerphone options within the
program. The modem chipset in the Modem may support
5
speakerphone, however, it does not have a microphone or
speakerphone socket to operate in speakerphone mode.
Installation –
1)
Insert CD, Click on Software FaxTalk SE to install software or
can use explore CD and go into FaxTalk SE folder , D:\FaxTalk
SE, double click on Setup to install.
2)
Choose setup language then click ok.
3)
At the install shield wizard click next
4)
Accept License agreement, click next
5)
Type in user name and organization, click next
6)
Destination folder, can change or just use the default and click
next
7)
Click Install to install the program
8)
On the Modem Settings window, select Agere Systems PCI soft
modem, click next
9)
After detection, click next to continue, at the Answer setting
window can select your desire setting and click next
10) At the Fax settings window can enter fax information for user
and click next
11) Click Finish to finish installation
6
To enable caller id Open FaxTalk Communicator and select configure> program> modem>
Advanced >Distinctive Ring/Caller ID setting
Check the box, “Use FaxTalk for Distinctive Ring/ Caller ID service
Check the box, “Enable Caller ID detection on incoming calls”
Make sure the Caller ID initialization string is set to +vcid=1
Modem Dialing Location
If you want to change your dialing location, please follow the instruction as
below:
Can open FaxTalk Communicator
Click on Configure> Dialing Properties, can edit your location
Or
For Windows XP --- Click Control Panel -> Phone And Modem Options ->
Under Dialing Rules click Edit, and then you can change your location.
FOR Windows VISTA --- Click Control Panel -> Phone And Modem
Options -> Under Dialing Rules click Edit, and then you can change your
location.
7
For More information on FaxTalk please check your CD FaxTalk User
Guide.
Limited Warranty.
Manufacturer warrants that the products sold hereunder are free from
defects in material and workmanship for a period of two (2) years from
manufacturing date. This limited warranty applies only to the original
purchaser of Jaton Product and is not transferable. This limited warranty
does not apply if failure to the Product Registration, or over thirty (30) days
from purchase (original invoice date). This Limited Warranty does not
cover any incompatibilities due to the user’s computer, hardware, software
or any related system configuration in which the Jaton Products interfaces.
Proof of purchase will be requiring before any consideration by
Manufacturer occurs.
Other Limits.
The forgoing is in lieu of all other warranties, expressed or implied.
Including but not limited to the implied warranties of merchantability
and fitness for a particular purpose. Manufacturer does not warrant
against damages or defects arising out of improper or abnormal use of
handling of the products; against defects or damages arising from improper
installation (where installation is by persons other than Manufacturer),
8
against defects in products or components not manufactured or installed by
Manufacturer, or against damages result from non-manufacturer made
products or components. This warranty does not apply if the Product has
been damaged by accident, abuse, nor misuse. This warranty also does not
apply to products upon which repairs have been affected or attempted by
persons other than pursuant to written authorization by Manufacturer.
Exclusive Obligation.
This warranty is exclusive. The sole and exclusive obligation of
Manufacturer shall repair or replace the defective products in the manner
and for the period provided above. Manufacturer shall not have any other
obligation with respect to the Products or any part thereof, whether based
on contract, tort, and strict liability or otherwise. Under no circumstances,
whether based on this Limited Warranty or otherwise, Manufacturer shall
not be liable for incidental, special, or consequential damage.
Other Statements.
Manufacturer’s employees or representatives’ ORAL OR OTHER
WRITTEN STATEMENTS DO NOT CONSTITUE WARRANTIES,
shall not be relied upon by Buyer, and are not a part of the contract for sale
or this Limited Warranty.
Terms and Conditions.
Direct Jaton Customer:
This warranty applies only for a
period of two (2) years from
9
purchase date of Jaton original
invoice.
Reseller/ Vendor:
This warranty applies only for a
period of two (2) years from
manufacturing date.
Registered User:
This warranty applies only for a
period of two (2) years from
purchase date AND customer must
register within 30 days of purchase
date from legal reseller.
Others:
If the products do not conform to this
Limited Warranty (as herein above
described), Manufacturer should
charge services such as repair,
replacement whether based on its
costs. Shipping and installation of the
replacement Products or replacement
parts shall be at User’s expense.
Services agreement:
(1) All applicants shall complete service request form from
Manufacturer.
10
(2) All returned checks will be charged a $20.00 fee by
Manufacturer.
(3) All repair and replacement services allow 4-6 weeks from
the date of receiving by Manufacturer.
(4) All products without warranties require service processing
fee $20 (payment in advance), which is not refundable.
Entire Obligation.
This Limited Warranty states the entire obligation of Manufacturer with
respect to the Products. If any part of this Limited Warranty is determined
to be void or illegal, the remainder shall remain in force and effect. Some
states do not allow limitation of implied warranties, or exclusive or
limitation on product incidental or consequential damages, so above
limitation may not apply to you. This warranty gives you specific legal
rights. You may have other rights that may vary from state to state.
This warranty applies only to this product, and is governed by the law of
the State of California.
Reducing Warranty Claim Rejections.
To reduce the potential of incurring damages not covered by Manufacturers
warranties, we strongly recommend the following:
11
•
•
•
•
read your manuals before installing peripherals and/or
before making changes to the machine’s configuration;
ask your dealer if there are any known problems with the
system requirements or installation procedures for any
add-on products that your are purchasing;
buy industry standard products where compatibility issue
are more likely to surface;
If you are unsure about installation for a new product,
contact your dealer’s service department.
We believe it is important for you to know and understand what your
warranty coverage provides and what it does not.
We also want you to be aware that most hardware warranties only relate to
the function of the hardware. In most cases, no assurances are given by the
manufacturer that the hardware item will work in conjunction with any
other hardware item. If a computer product is not working because it is not
compatible with another product, or because it has not been properly
installed and set-up, the manufacturer does not pay for the service time. To
help avoid these inconveniences, contact a professional consultant that one
can help you determine the possibility of incompatibility issue before you
purchase add-on or accessories.
12
Warranty Service Use Only
Serial Number - ten or eleven digit code, the serial number consists of the following parts:
Packaging Type
Manufactured Date Code
A
00 8
Production Numerical Code
000015
Year Month
XXXXX-XXX-XX
xxxx/xxxx
S/N: A008000015
00.0
XXXX XX XXXXXX
Product Label and Manufactured Date Code
13
FCC Shielded Cable Warning:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. Operation is
subject to the following conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation,
“SHIELD INTERFERENCE CABLE (S) MUST BE USED ACCORDING
TO FCC 15.27©.”
CAUTION:
Changes or modifications not expressly approved by the Manufacturer
could void your authority to operate this equipment in accordance with
FCC rules and regulations.
TRADEMARK AND COPYRIGHT:
All Trademarks and Registered Trademarks belong to respective owners.
©2009 Jaton Corporation. All rights reserved.
14