Pyle PDWM2700 microphone Datasheet

Add to my manuals
4 Pages

advertisement

Pyle PDWM2700 microphone Datasheet | Manualzz

TROUBLE SHOOTING

Please read and check the following points before asking for service.

The wireless microphone fails fo work:

--Check the microphone battery by switching the microphone ON. If power LED indicator lights red, replace the battery.

--Check the POWER indicator on the receiver unit is ON. If not, check the mains power adapter is firmly plugged into a working

mains socket.

--Check the amplifier system is ON and the microphone controls set correctly.

--Check the radio microphone jack lead is firmly connected into the output socket on the rear panel of the receiver unit and

into the MIC input socket on your amplifier.

The working range is limited:

--Check the microphone battery condition(see above)

--Check the aerials are fully extended. Adjust the position of the aerials to achieve the best reception.

--Check the settings of the microphone controls on the amplifier. Adjust volume and tone to get the beat sound without any

trace of feedback.

www.pyleaudio.com

R PDWM2700

TWO CHANNELS VHF WIRELESS MICROPHONE

OPEN

MIN MAX

R

P R O F E S S I O N A L

W I R E L E S S M I C R O P H O N E

VHF

PDWM2700

SIGNAL-A AUDIO POWER SIGNAL-A AUDIO

MIN MAX

USER'S MANUAL

Thank you for choosing our VHF wireless microphone system. We strongly suggest that you carefully study these instructions before attempting to operate the system.

CONTENTS

P1--------Precautions

P2--------Handheld microphone

P3--------Body pack transmitter

P4--------Receiver

P5--------Instalation

P6--------Specifications

P7--------Troubleshooting

PRECAUTIONS

1.Avoid exposure of the system to rain or moisture.

2.No user-serviceable parts inside the system. Refer all servicing to a qualified technician only.

3.Handle the microphone carefully, dropping or other shocks may cause failure.

4.Aoid using the system where it may be subjected to heat, such as in direct sunlight, near radiators or other heat sources.

5.Should any liquid be spilt on the system, stop using it immediately. It may be possible to dry the system, but you should have

it checked by a qualified technician before using it again.

6.Take care with the mains power adapter and lead. If damaged in any way, do not use the with the system, and refer to a qua-

lified for repair.

7.Only use the system with the supplied components, do not attempt to use with any other mains power supply adapter or microphone.

8.If the microphone is not going to be used for a time, remove the battery to prevent leakage. In the event of electrolyte leakage inside the battery compartment, carefully remove using a damp cloth. Take care not to get battery electrolyte in contact with

your skin, however, if it does, wash your hands under a running tap. If electrolyte comes into contact with your eyes, seek

medical advice immediately.

9.Only replace the battery with the same or an equivalent type.

10.Only replace the battery with the same or an environmentally friendly manner in accordance with the relevant legislation.

11.Do not use any solvents to clean any part of the radio microphone system.

--1--

SPECIFICATIONS

A.Overall system

1.Oscillation mode:

2.Carrier Frequency Range

3.Frequency Stability:

4.Max Deviation:

5.Dynamic Range:

6.S/N Ration:

7.T.H.D:

8.Frequency Response:

9.Operating Range:

Quartz controlled

VHF 160~270MHz

+/-0.005%

+/-56KHz with level limiting

>110dB

>100dB

<0.5dB

100Hz-15KHz

50M

C.Transmitter

1.Mike capsule:

2.Antenna:

3.RF Output:

4.Spurious:

5.Power Supply:

Handheld: dynamic

Headset or lavalier MIC: condenser

Built-in housing(Handheld MIC) external (Belt pack)

<10mW

<-40dBC

9V battery

B.Receiver

1.Sensitivity:

2.Image Rejection.

3.Stability:

4.Audio output:

5.Power supply:

6dB¦V at SIN >70dB

>60dB

>80dB

-12db/600ohm unbalanced and balanced

12V 500mA

--6--

INSTALLATION HANDHELD MICROPHONE

UNSCREW BATTERY

COVER TO INSERT

BATTERY

AMPLIFIER

SPEAKERS

MIX

ANT.B BALANCED AF.OUT

RADIO MIC

RECEIVER UNIT

DC 12V

To connect the wireless microphone to your amplifier system:

Refer to above installation diagram.

ANT.A

MAINS POWER

ADAPTER

Using the supplied 6.35mm to 6.35mm lead, connect from the AF OUT jack of the receiver to the MIC INPUT socket on your amplifier.

Plug one end of the mains power adapter into a suitable mains socket.

Plug the other end of the adapter into receiver DC 12V input socket.

--5--

BATTERY CONDITION

INDICATOR

POWER SWITCH POWER COVER

1.Unscrew the battery cover at the end of the microphone. Install the provided 9 volt battery and then close the cover. Make

sure to connect with the correct polarity.

2.Move power switch to ON position. Power LED indicator will flash once and then go off. This indicates correct operation. If

power LED indicator lights red, this indicates the battery is low. Please replace with new battery.

3.Move power switch to center to mute the microphone.

4.If the microphone is not going to be used for a long period of time, please take out the battery to prevent damage by battery

leakage.

--2--

BODYPACK TRANSMITTER

VOLUME CONTROL

(HIGH/LOW)

ON/OFF LED MIC IN

Headset MIC

OPEN

OPEN

Lavalier MIC(Optional)

1.Slide up the battery cover in the front of the body pack as per above sketch map. Install the provided 9 volt battery and the

battery cover. Make sure to connect with the correct polarity.

2.Move power switch to ON position. Power LED indicator will flash once and then go off. This indicates correct operation.

If power LED indicator lights red, this indicates the battery is low. Please replace with new battery.

3.Move power switch to centre to mute the microphone.

4.Adjust the volume control to you get the sufficient sound from your speaker.

5.If the microphone is not going to be used for a long period of time, please take out the battery to prevent damage by battery

leakage.

--3--

BODYPACK TRANSMITTER

MIN MAX

R

P R O F E S S I O N A L

W I R E L E S S M I C R O P H O N E

VHF

P D W M 2 7 0 0

SIGNAL-A AUDIO POWER SIGNAL-A AUDIO

MIN MAX

MIX

ANT.B BALANCED AF.OUT

DC 12V

ANT.A

1.Switch on the wireless microphone receiver unit by pressing the POWER switch and the POWER light will illuminate to show

the receiver unit is working.

2.Fully extend the aerials to the maximum height.

3.Switch ON the transmitter. Power LED indicator will flash once the go off. When the microphone is ON, the receiver RF

indicator will light.

4.Adjust the volume and tone levels of your amplifier system as well as the receiver & the body pack as required.

5.When the transmitter is not going to be used for a long period of time, please take out the battery from transmitter.

Note that switching the microphone on and off can cause interference that will be heard if the microphone volume level of the amplifier system is still set high.

--4--

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement