Add-On Computer Peripherals (ACP) SFP+ 1550nm LC Datasheet

10G-SFPP-ER-AO

BROCADE, 10BASE-ER SFP+

1550NM 40KM REACH LC

10G-SFPP-ER-AO

10Gbase SFP+ Transceiver

Features

• Compliant to SFP+ Electrical MSA SFF-8431

• Compliant to SFP+ Mechanical MSA SFF-8432

• Multi-rate compliance for Ethernet and Fiber Channel

• Transmission distance up to 40km over SMF

• 0°C to +70°C case operating temperature range

• 1550nm EA-DFB Transmitter

• RoHS 6/6 compliant

• Operating data rate up to 10.3Gbps

Product Description

The 10G-SFPP-ER-AO Transceiver is a single mode transceiver is small form factor pluggable module for duplex optical data communications such as

10GBASE-ER/EW defined by IEEE 802.3ae. It is with the SFP+ 20-pin connector to allow hot plug capability.

Functional Description

This module is designed for single mode fiber and operates at a nominal wavelength of 1550 nm. The transmitter section uses a 1550nm multiple quantum well DFB, which is class 1 laser compliant according to International

Safety Standard IEC-60825. The receiver section uses an integrated InGaAs detector preamplifier (IDP) mounted in an optical header and a limiting postamplifier IC.

AddOn Computer Phone: 877.292.1701 Page 1 of 4

10G-SFPP-ER-AO

BROCADE, 10BASE-ER SFP+

1550NM 40KM REACH LC

Electrical and Optical Characteristics

Rating

Storage Ambient Temperature Range

Powered Case Temperature Range

Conditions

Operating Relative Humidity

Supply Voltage Range @ 3.3V

Non condensing

Symbol

Ts

Min Max

-40 +85

Jc

RH

0

0

+75

95

VCC3 -0.5 3.6

Units

°C

°C

%

V

Power Supply Current Icc <1.5 W

Static Discharge Voltage Speed Pins on High

Static Discharge Voltage excluding

High Speed Pins

Static Discharge Voltage Module on

SFP+

1

2

15

8 kV kV kV

Any stress beyond the maximum ratings may result in permanent damage to the device.

Specifications are guaranteed only under recommended operating conditions .

Optical Transmitter

Parameter Conditions Symbol Min Typ Max Units

Nominal Wavelength λΤΡΠ 1480 1550 1600 nm

Optical Receiver

HBM human body model per JEDEC

JESD22-A114-B

HBM human body model

EN61000-4-2

Criterion B: Air

Discharge Direct

Contact discharge

Parameter

Maximum Input

Power

Center Wavelength

Conditions Symbol

PMAX

λΧ

Min Typ

1260 1550

Max Units

0

1600 dBm nm

Receiver Sensitivity Se -16

Digital Optical Monitoring

Transceivers offer the ability to monitor important module parameter during operation.

The five parameters listed below are continuously monitored for getting information about the current module status. All data is calibrated internally; there is no need for external post processing.

0 dBm

AddOn Computer Phone: 877.292.1701 Page 2 of 4

10G-SFPP-ER-AO

BROCADE, 10BASE-ER SFP+

1550NM 40KM REACH LC

Temperature

Internally measured temperature data is represented as two’s complement of a signed

16-bit value in increments of 1/256 °C over a range of -40 to +100°C. Accuracy is better than +/-3%.

Supply Voltage (VCC)

Internally measured supply voltage. Represented as a 16-bit unsigned integer with the voltage defined as the full 16 bit value (0 – 65535) with LSB equal to 100 µVolt, which yields to a total range of 0 to +6.55 Volts. Accuracy is better than +/-3%.

Laser Bias Current

VCSEL bias current. Represented as a 16 bit unsigned integer with the current defined as the full 16-bit value (0 – 65535) with LSB equal to 2 µA, valid range is 0 to 20 mA.

Accuracy is better than +/-10%.

Optical Transmitter Power

TX output power measurement is based on internal monitor diode feedback.

Represented as a 16-bit unsigned integer with the power defined as the full 16 bit value

(0–65535) with LSB equal to 0.1µW. Accuracy is better than +/-3dB over a range of

Pavmin to Pavmax.

Receiver Optical Power

RX input power measurement is based on photodiode diode current. Represented as a

16-bit unsigned integer with the power defined as the full 16 bit value (0 – 65535) with

LSB equal to 0.1 µW. Accuracy is better than +/-3dB over a range of -12dBm to -1dBm.

Note: The specified characteristics are met within the recommended range of operating conditions regarding temperature and voltage.

Regulatory Compliance

Module Safety

Add-On Computer Peripherals SFP+ modules are designed to meet international requirements and standards in terms of product safety. Tests were performed according to IEC 60950-1:2001 (CB scheme).The module is RoHS compliant according to the

European Parliament requirements on the restriction of the use of hazardous substances in electrical and electronic equipment (RoHS). The modules optical output power meet Class 1 requirements for laser safety.

Requirements Standard Status

Module

Safety

RoHS

IEC 60950-1:2001 EN 60950-

1:2001

RoHS Directive 2002/95/EC

TUV Report / Certificate available CB

Report / Certificate available

RoHS 6/6 compliant Certificate of

Compliance Amendment 4054 (2005/747/EC) compliance available

AddOn Computer Phone: 877.292.1701 Page 3 of 4

10G-SFPP-ER-AO

BROCADE, 10BASE-ER SFP+

1550NM 40KM REACH LC

Laser Eye CDRH 21 CFR 1040.10 and Laser Class 1 according to FDA

Safety 1040.11 IEC 60825-1 Rev2 2007 Laser Class 1 according to IEC Rev2

ESD & Electromagnetic compatibility

Add-On Computer Peripherals SFP+ modules are designed to withstand high ESD voltages. Its excellent performances in terms of EMI allow system designers to integrate the module in high density applications.

Requirements Standard Status

Electro Static

Discharge to the

Electrical Pins (ESD)

EIA/JESD22-A114-B MIL-

STD 883C Method 3015.7

Immunity to ESD IEN 61000-4-2

(housing, receptacle) IEC61000-4-2

Electromagnetic FCC Part 15, Class B EN

Exceeds requirements Class 1B

(>1000V)

Exceeds requirements

Discharges ranging from 2kV to

25kV without damages to the transceiver

Exceeds requirements Class B

Emission (EMI) 55022 Class B CISPR 22 with more than 6dB margin

Contact Information

Add-On Computer Peripherals is a leading supplier of Memory Upgrade, Network

Transceivers and Network connectivity products to Channel Partners, Resellers and

OEMs, with more than seventeen years of direct industry experience. Add-On Computer

Peripherals (ACP) has been the exclusive supplier to Ingram Micro's "Memory

Upgrades" program for the past nine years.

ACP maximizes profitable opportunities for our partners. Our ability to source product worldwide, ensures that our pricing will always be competitive. Offering turnkey solutions, ACP has forged a reputation as a solutions provider, delivering high quality, cost effective product in a timely and reliable manner.

Corporate offices:

Add-On Computer Peripherals

34A Mauchly

Irvine, CA 92618

Tel: 877-292-1701

Fax: 949-861-2812

Email: [email protected]

Email: [email protected]

Web: http://www.addoncomputer.com

AddOn Computer Phone: 877.292.1701 Page 4 of 4