S
P
E
C
F
I
L
E
The PT-EZ570L is not equipped with a lens.
P ro d u c t N u m b e r :
PT-EZ570/EZ570L
P ro d u c t N a m e :
LCD Projectors
As of July 2012. Specifications and appearance are subject to change without notice.
SFL12M004-2
1/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Specifications
Main unit
Power supply
Power consumption
Optical system
LCD panel
Lens
Panel size
Display method
Pixels
Pixel configuration
PT-EZ570
PT-EZ570L
Lamp
Screen size
Brightness* 2
Center-to-corner uniformity* 2
Contrast* 2
Resolution
Scanning frequency
HDMI/DVI-I
RGB
YPBPR (YCBCR)
Video/S-Video
Optical axis shift
100 – 240 V AC, 50/60 Hz
490 W (492 VA) (0.4 W with STANDBY MODE set to ECO* 1 , 11 W with
STANDBY MODE set to NETWORK .)
Dichroic mirror separation/prism synthesis system
19.2 mm (0.76 inches) diagonal (16:10 aspect ratio)
Transparent LCD panel (× 3, R/G/B)
2,304,000 (1,920 × 1,200) × 3, total of 6,912,000 pixels
Stripe
Powered zoom/focus lens (1.7– 2.8:1), F 1.7 – 2.3, f 26.9 – 45.4 mm
Optional powered zoom/focus lenses and fixed-focus lens
330 W UHM lamp
1.02 –10.16 m (40 – 400 inches), 16:10 aspect ratio
5,000 lumens (LAMP POWER: AUTO/NORMAL)
90%
5,000:1 (full on / full off, LAMP POWER: AUTO)
1,920 × 1,200 pixels
fH: 26 – 80 kHz, fV: 23 – 85 Hz, dot clock: 162 MHz or lower
fH: 15 –120 kHz, fV: 48 –100 Hz, dot clock: 230 MHz or lower
(Signals exceeding the dot clock rate of 163 MHz are downsampled.)
480i (525i):
fH 15.75 kHz; fV 60 Hz,
576i (625i):
fH 15.63 kHz; fV 50 Hz,
480p (525p):
fH 31.50 kHz; fV 60 Hz,
576p (625p):
fH 31.25 kHz; fV 50 Hz,
720 (750)/60p:
fH 45.00 kHz; fV 60 Hz,
720 (750)/50p:
fH 37.50 kHz; fV 50 Hz,
1035/60i:
fH 33.75 kHz; fV 60 Hz,
1080 (1125)/60i:
fH 33.75 kHz; fV 60 Hz,
1080 (1125)/50i:
fH 28.13 kHz; fV 50 Hz,
1080/25p:
fH 28.13 kHz; fV 25 Hz,
1080/25sF:
fH 28.13 kHz; fV 50 Hz,
1080/24p:
fH 27.00 kHz; fV 24 Hz,
1080/24sF:
fH 27.00 kHz; fV 48 Hz,
1080/30p:
fH 33.75 kHz; fV 30 Hz,
1080/30sF:
fH 33.75 kHz; fV 60 Hz,
1080/60p:
fH 67.50 kHz; fV 60 Hz,
1080/50p:
fH 56.25 kHz; fV 50 Hz
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60]
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Vertical: ±60% (powered), horizontal: ±10% (powered)
NOTE: Optical axis shift function cannot be operated when used with the ET-ELW21.
Keystone correction range
Installation
Built-in speaker
As of July 2012
SFL12M004-2
Size
Output power
Vertical: ±30° (with vertical correction only)
Horizontal: ±30° (with horizontal correction only)
Ceiling/floor, front/rear
3.7 cm (1-15/32 inches) (round) × 1
10 W (monaural)
2/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Terminals
INPUT 1
HDMI IN
DVI-D IN
RGB IN
R, G, B
Menu selection
HDMI 19-pin × 1, Deep Color, HDCP compatible
480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p, 1035/60i,
1080 (1125)/60i, 1080 (1125)/50i, 1080/25p, 1080/25sF, 1080/24p,
1080/24sF, 1080/30p, 1080/30sF, 1080/60p, 1080/50p,
VGA (640 × 480) – WUXGA* 2 (1,920 × 1,200)
Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz,
32 kHz)
DVI-D 24-pin × 1, DVI 1.0 compliant, compatible with HDCP, compatible with single link only
480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p, 1035/60i,
1080 (1125)/60i, 1080 (1125)/50i, 1080/25p, 1080/25sF, 1080/24p,
1080/24sF, 1080/30p, 1080/30sF, 1080/60p, 1080/50p,
VGA (640 × 480) – WUXGA* 2 (1,920 × 1,200)
D-sub HD 15-pin (female) × 1
R: 0.7 Vp-p, 75 ohms;
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;
B: 0.7 Vp-p, 75 ohms;
HD/VD, SYNC: high impedance, TTL (positive/negative)
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
INPUT 2
[RGB input]
R, G, B
Menu selection
BNC × 5 (RGB/YPBPR/YCBCR × 1)
R: 0.7 Vp-p, 75 ohms;
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;
B: 0.7 Vp-p, 75 ohms;
HD/VD, SYNC: high impedance, TTL (positive/negative)
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y, PB (CB), PR (CR)
Y: 1.0 Vp-p (including sync signal);
PB (CB), PR (CR): 0.7 Vp-p, 75 ohms
VIDEO
BNC × 1, 1.0 Vp-p, 75 ohms
INPUT 3
Menu selection
[Component input]
RCA pin × 3 (YPBPR/YCBCR × 1)
Y, PB (CB), PR (CR)
Y: 1.0 Vp-p (including sync signal);
PB (CB), PR (CR): 0.7 Vp-p, 75 ohms
VIDEO
RCA pin × 1, 1.0 Vp-p, 75 ohms
S-VIDEO
Mini DIN 4-pin × 1, Y: 1.0 Vp-p; C: 0.286 Vp-p, 75 ohms
MONITOR OUT (RGB output) D-sub HD 15-pin (female) × 1
R: 0.7 Vp-p, 75 ohms;
G: 0.7 Vp-p (1.0 Vp-p for sync on G), 75 ohms;
B: 0.7 Vp-p, 75 ohms;
HD/VD, SYNC: high impedance, TTL (positive/negative)
AUDIO IN 1
M3 (L, R) × 1, 0.5 Vrms, input impedance: 22 kilohms or more
AUDIO IN 2
M3 (L, R) × 1, 0.5 Vrms, input impedance: 22 kilohms or more
AUDIO IN 3
RCA (L, R) × 2, 0.5 Vrms, input impedance: 22 kilohms or more
VARIABLE AUDIO OUT
M3 (L, R) × 1 (monitor out: 0 – 2.0 Vrms, variable)
SERIAL IN
D-sub 9-pin (female) × 1, for external control (RS-232C compliant)
REMOTE IN
M3 jack × 1 for wired remote control or link control
LAN
RJ-45 × 1, for network connection, 100Base-TX/10Base-T, compliant
with PJLink™
Power cord length
3.0 m (9 ft 10 in)
Cabinet materials
Molded plastic
Dimensions (W × H × D)
PT-EZ570
489.5 × 164* 4 × 434 mm
(19-9/32 × 6-15/32 * 4 × 17-3/32 inches) (with supplied lens)
489.5 × 164* 4 × 370 mm
PT-EZ570L
(19-9/32 × 6-15/32 * 4 × 14-9/16 inches) (without lens)
Approx. 10.3 kg (22.7 lbs) (with supplied lens)
Weight
PT-EZ570
Approx. 9.6 kg (21.2 lbs) (without lens)
PT-EZ570L
As of July 2012
SFL12M004-2
3/17
S
P
E
C
F
I
LCD Projectors
Operation noise* 2
Operating temperature
Operating humidity
Remote control unit
Power supply
Operation range* 5
Dimensions (W × H × D)
Weight
L
E
PT-EZ570/EZ570L
37 dB (LAMP POWER: NORMAL), 31 dB (LAMP POWER: ECO 1 / ECO 2)
0–40 °C (32–104 °F) up to 1,000 m (3,280 ft) above sea level, with fan
control set to OFF,
0–30 °C (32–86 °F) between 1,000 m and 2,000 m (3,280 ft and 6,561
ft) above sea level, with fan control set to ON 1,
0–30 °C (32–86 °F) between 2,000 m and 2,700 m (6,561 ft and 8,858
ft) above sea level, with fan control set to ON 2.
20%– 80% (no condensation)
3 V DC (R03/LR03/AAA type battery × 2)
Approx. 5 m (16 ft 5 in) when operated from directly in front of the signal receptor
48 × 145 × 27 mm (1-7/8 × 5-23/32 × 1-1/16 inches)
Approx. 102 g (3.6 oz) (including batteries)
Supplied accessories
Power cord (× 1)
Power cord holder (× 1)
Wireless/wireled remote control unit (× 1)
Batteries for remote control (AAA/R03/LR03 type × 2)
Computer cable (× 1)
Software CD-ROM (Logo Transfer Software, Multi Projector Monitoring
& Control Software) (× 1)
Optional accessories
Zoom lens (1.3–1.7:1)
Zoom lens (2.8– 4.6:1)
Zoom lens (4.6 – 7.2:1)
Fixed-focus lens (0.8:1)
Ceiling mount bracket
Bracket assembly
Replacement lamp unit
Replacement filter unit
ET-ELW20
ET-ELT20
ET-ELT21
ET-ELW21
ET-PKE200H (for high ceilings)
ET-PKE200S (for low ceilings)
ET-PKE200B
ET-LAE200
ET-RFE200
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
* 1 When the standby mode is set to eco, network functions such as power on over the LAN network will not operate, and the serial output terminal cannot be used. Also, only certain commands can be received for external control using the serial terminal.
* 2 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
* 3 WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
* 4 With legs at shortest position.
* 5 Operation range differs depending on environments.
As of July 2012
SFL12M004-2
4/17
S
P
E
F
C
I
L
E
PT-EZ570/EZ570L
LCD Projectors
9
(11/32)
164
( 6-15/32)
155
( 6-3/32)
370 (14-9/16 )
345 (13-19/32)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
The illustration shows the PT-EZ570.
64 (2-17/32)
434 (17-3/32)
Dimensions
412 (16-7/32)
489.5 (19-9/32)
286 (11-1/4)
Terminals
1
LAN
2
3
MONITOR OUT
VIDEO/G/Y B/PB
R/PR
4
5
DVI-D
RGB
S-VIDEO PB/CB
1
INPUT 1
REMOTE IN SERIAL IN
L
R
SYNC/HD
INPUT 2
6
VD
2
VIDEO/Y PR/CR
INPUT 3
7
8
3
VAEIABLE
AUDIO OUT
AUDIO IN
9
11
10 12
13 14
1
LAN connector
2
RGB output
3
RGB input
4
HDMI Input
5
DVI-D input
6
RGB/component/video input
7
S-Video
8
Component/video input
9
Audio 1 input
10 Audio 2 input
11 Audio 3 input
12 Remote input
13 Audio output
14 Serial input
As of July 2012
SFL12M004-2
5/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
H
∅54
( 2-1/8 )
Upper edge of projected image
951–1,551* 2
( 37-7/16 – 61-1/16 ) * 2
860 –1,460* 2
( 33-27/32–
2
57-15/32)*
Standard setting-up position
*1 When the lens protrudes to the maximum.
A: 83.5 mm (3-9/32 in) with the ET-ELW20
64 mm (2-17/32 in) with the supplied lens
88 mm (3-15/32 in) with the ET-ELT20
84 mm (3-5/16 in) with the ET-ELT21
54 mm (2-1/8 in) with the ET-ELW21
*2 Adjustable in 30 mm (1-3/16 in) steps.
L
A* 1
Projected image
185.5
(7-5/16 )
184.5
(7-1/4)
H
L
Lower edge of projected image
NOTE:
Illustrations show the projector
i nstalled using optional ceiling mount
bracket ET-PKE200H and bracket assembly
ET-PKE200B.
120
(4-23/32)
60
( 2-3/8 )
This illustration is not drawn to scale.
L
60
( 2-3/8 )
Projected image
60
( 2-3/8 )
120
(4-23/32)
60
( 2-3/8 )
unit : mm (inch)
Caution:
• All construction work should be done by a qualified technician.
• When mounting to the ceiling, use the special mounting bracket. To prevent the projector from swaying or dropping, attach the wire between the mounting bracket and the ceiling.
As of July 2012
SFL12M004-2
6/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Projection distance for 16:10 aspect ratio screen
Unit: meters
Distance to screen (L)
Screen size
(diagonal)
Zoom
ET-ELW20
Zoom lens
[m]
Supplied lens
Fixed-focus
ET-ELT20
Zoom lens
ET-ELT21
Zoom lens
Height from the edge
of screen to
center of lens (H)
ET-ELW21
Fixed-focus
lens
Zoom
lenses
Fixedfocus
lens
[in]
min.
max.
min.
max.
min.
max
min.
max.
1.02 / 40
1.02
1.41
1.36
2.35
2.29
3.81
3.72
6.03
0.63
-0.05 – 0.59
0.27
1.27 / 50
1.29
1.77
1.71
2.95
2.89
4.79
4.70
7.59
0.80
-0.07 – 0.74
0.34
1.52 / 60
1.55
2.14
2.06
3.55
3.49
5.77
5.68
9.15
0.97
-0.08 – 0.89
0.40
1.78 / 70
1.82
2.50
2.42
4.16
4.09
6.75
6.66
10.71
1.15
-0.09 – 1.04
0.47
2.03 / 80
2.09
2.87
2.77
4.76
4.69
7.73
7.65
12.27
1.32
-0.11 – 1.19
0.54
2.29 / 90
2.36
3.23
3.12
5.36
5.30
8.71
8.63
13.83
1.49
-0.12 – 1.33
0.61
2.54 / 100
2.63
3.60
3.48
5.96
5.90
9.69
9.61
15.39
1.66
-0.14 – 1.48
0.67
3.05 / 120
3.16
4.33
4.18
7.16
7.10
11.65
11.57
18.51
2.00
-0.16 – 1.78
0.81
3.81 / 150
3.97
5.42
5.24
8.96
8.90
14.59
14.52
23.19
2.52
-0.20 – 2.22
1.01
5.08 / 200
5.31
7.25
7.01
11.96
11.91
19.49
19.43
30.99
3.38
-0.27 – 2.96
1.35
6.35 / 250
6.65
9.07
8.77
14.96
14.91
24.39
24.34
38.79
4.24
-0.34 – 3.70
1.68
7.62 / 300
7.99
10.90
10.54
17.97
17.92
29.29
29.25
46.59
5.10
-0.40 – 4.44
2.02
10.16 / 400
10.67
14.55
14.07
23.97
23.93
39.09
39.07
62.19
6.81
-0.54 – 5.92
2.69
Unit: feet
Distance to screen (L)
Screen size
(diagonal)
Zoom
ET-ELW20
Zoom lens
[m]
Supplied lens
Fixed-focus
ET-ELT20
Zoom lens
ET-ELT21
Zoom lens
ET-ELW21
Fixed-focus
lens
Height from the edge
of screen to
center of lens (H)
Zoom
lenses
Fixedfocus
lens
[in]
min.
max.
min.
max.
min.
max
min.
max.
1.02 / 40
3.3
4.6
4.5
7.7
7.5
12.5
12.2
19.8
2.1
-0.2 – 1.9
0.9
1.27 / 50
4.2
5.8
5.6
9.7
9.5
15.7
15.4
24.9
2.6
-0.2 – 2.4
1.1
1.52 / 60
5.1
7.0
6.8
11.7
11.5
18.9
18.6
30.0
3.2
-0.3 – 2.9
1.3
1.78 / 70
6.0
8.2
7.9
13.6
13.4
22.1
21.9
35.1
3.8
-0.3 – 3.4
1.6
2.03 / 80
6.9
9.4
9.1
15.6
15.4
25.4
25.1
40.3
4.3
-0.4 – 3.9
1.8
2.29 / 90
7.7
10.6
10.2
17.6
17.4
28.6
28.3
45.4
4.9
-0.4 – 4.4
2.0
2.54 / 100
8.6
11.8
11.4
19.5
19.3
31.8
31.5
50.5
5.4
-0.4 – 4.9
2.2
3.05 / 120
10.4
14.2
13.7
23.5
23.3
38.2
38.0
60.7
6.6
-0.5 – 5.8
2.7
3.81 / 150
13.0
17.8
17.2
29.4
29.2
47.9
47.6
76.1
8.3
-0.7 – 7.3
3.3
5.08 / 200
17.4
23.8
23.0
39.2
39.1
63.9
63.8
101.7
11.1
-0.9 – 9.7
4.4
6.35 / 250
21.8
29.8
28.8
49.1
48.9
80.0
79.9
127.3
13.9
-1.1 – 12.2
5.5
7.62 / 300
26.2
35.8
34.6
58.9
58.8
96.1
96.0
152.8
16.7
-1.3 – 14.6
6.6
10.16 / 400
35.0
47.7
46.2
78.6
78.5
128.2
128.2
204.0
22.4
-1.8 – 19.4
8.8
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• The zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• The brightness varies depending on the zoom setting.
Note: When the fixed-focus lens ET-ELW21 is mounted, the optical lens shift function cannot be used.
As of July 2012
SFL12M004-2
7/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Projection distance for 16:9 aspect ratio screen
Unit: meters
Distance to screen (L)
Screen size
(diagonal)
Zoom
ET-ELW20
Zoom lens
[m]
Supplied lens
Fixed-focus
ET-ELT20
Zoom lens
ET-ELT21
Zoom lens
Height from the edge
of screen to
center of lens (H)
ET-ELW21
Fixed-focus
lens
Zoom
lenses
Fixedfocus
lens
[in]
min.
max.
min.
max.
min.
max
min.
max.
1.02 / 40
1.05
1.45
1.40
2.42
2.36
3.92
3.83
6.20
0.65
-0.05 – 0.55
0.25
1.27 / 50
1.32
1.82
1.76
3.04
2.98
4.92
4.84
7.81
0.83
-0.06 – 0.69
0.31
1.52 / 60
1.60
2.20
2.12
3.66
3.59
5.93
5.84
9.41
1.00
-0.08 – 0.82
0.37
1.78 / 70
1.87
2.57
2.49
4.27
4.21
6.94
6.85
11.01
1.18
-0.09 – 0.96
0.44
2.03 / 80
2.15
2.95
2.85
4.89
4.83
7.95
7.86
12.62
1.36
-0.10 – 1.10
0.50
2.29 / 90
2.43
3.32
3.21
5.51
5.45
8.95
8.87
14.22
1.53
-0.11 – 1.23
0.56
2.54 / 100
2.70
3.70
3.57
6.12
6.06
9.96
9.88
15.82
1.71
-0.13 – 1.37
0.62
3.05 / 120
3.25
4.45
4.30
7.36
7.30
11.97
11.90
19.03
2.06
-0.15 – 1.64
0.75
3.81 / 150
4.08
5.58
5.39
9.21
9.15
15.00
14.93
23.84
2.59
-0.19 – 2.06
0.93
5.08 / 200
5.46
7.45
7.20
12.30
12.24
20.03
19.98
31.86
3.47
-0.25 – 2.74
1.25
6.35 / 250
6.84
9.33
9.02
15.38
15.33
25.07
25.02
39.87
4.36
-0.31 – 3.42
1.56
7.62 / 300
8.21
11.20
10.83
18.47
18.42
30.11
30.07
47.89
5.24
-0.37 – 4.11
1.87
10.16 / 400
10.97
14.96
14.46
24.64
24.60
40.18
40.17
63.92
7.00
-0.50 – 5.48
2.49
Unit: feet
Distance to screen (L)
Screen size
(diagonal)
Zoom
ET-ELW20
Zoom lens
[m]
Supplied lens
Fixed-focus
ET-ELT20
Zoom lens
ET-ELT21
Zoom lens
ET-ELW21
Fixed-focus
lens
Height from the edge
of screen to
center of lens (H)
Zoom
lenses
Fixedfocus
lens
[in]
min.
max.
min.
max.
min.
max
min.
max.
1.02 / 40
3.4
4.8
4.6
7.9
7.7
12.8
12.6
20.4
2.1
-0.2 – 1.8
0.8
1.27 / 50
4.3
6.0
5.8
10.0
9.8
16.2
15.9
25.6
2.7
-0.2 – 2.3
1.0
1.52 / 60
5.2
7.2
7.0
12.0
11.8
19.5
19.2
30.9
3.3
-0.3 – 2.7
1.2
1.78 / 70
6.1
8.4
8.2
14.0
13.8
22.8
22.5
36.1
3.9
-0.3 – 3.2
1.4
2.03 / 80
7.1
9.7
9.3
16.0
15.8
26.1
25.8
41.4
4.4
-0.3 – 3.6
1.6
2.29 / 90
8.0
10.9
10.5
18.1
17.9
29.4
29.1
46.7
5.0
-0.4 – 4.1
1.8
2.54 / 100
8.9
12.1
11.7
20.1
19.9
32.7
32.4
51.9
5.6
-0.4 – 4.5
2.0
3.05 / 120
10.7
14.6
14.1
24.1
23.9
39.3
39.0
62.4
6.8
-0.5 – 5.4
2.5
3.81 / 150
13.4
18.3
17.7
30.2
30.0
49.2
49.0
78.2
8.5
-0.6 – 6.7
3.1
5.08 / 200
17.9
24.4
23.6
40.3
40.2
65.7
65.5
104.5
11.4
-0.8 – 9.0
4.1
6.35 / 250
22.4
30.6
29.6
50.5
50.3
82.2
82.1
130.8
14.3
-1.0 – 11.2
5.1
7.62 / 300
26.9
36.8
35.5
60.6
60.4
98.8
98.7
157.1
17.2
-1.2 – 13.5
6.1
10.16 / 400
36.0
49.1
47.4
80.8
80.7
131.8
131.8
209.7
23.0
-1.6 – 18.0
8.2
• The value for L (distance to screen) varies slightly within ±5% depending on the zoom lens characteristics.
• The zoom lens characteristics may cause slight image distortion.
• When vertical keystone correction is used, the image is corrected in the direction that reduces its projected size.
• The brightness varies depending on the zoom setting.
Note: When the fixed-focus lens ET-ELW21 is mounted, the optical lens shift function cannot be used.
As of July 2012
SFL12M004-2
8/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 16:10
ET-ELW20
minimum
maximum
L (m) = (diagonal screen size in inches) × 0.026816 - 0.055497
L (m) = (diagonal screen size in inches) × 0.036511 - 0.053400
Supplied lens
minimum
maximum
L (m) = (diagonal screen size in inches) × 0.035305 - 0.054882
L (m) = (diagonal screen size in inches) × 0.060045 - 0.048228
ET-ELT20
minimum
maximum
L (m) = (diagonal screen size in inches) × 0.060102 - 0.114022
L (m) = (diagonal screen size in inches) × 0.098001 - 0.112874
ET-ELT21
minimum
maximum
L (m) = (diagonal screen size in inches) × 0.098214 - 0.212284
L (m) = (diagonal screen size in inches) × 0.155996 - 0.210772
ET-ELW21
(fixed focus)
L (m) = (diagonal screen size in inches) × 0.017178 - 0.057678
ET-ELW20
minimum
maximum
L (m) = (diagonal screen size in inches) × 0.027561 - 0.055497
L (m) = (diagonal screen size in inches) × 0.037526 - 0.053400
Supplied lens
minimum
maximum
L (m) = (diagonal screen size in inches) × 0.036286 - 0.054882
L (m) = (diagonal screen size in inches) × 0.061714 - 0.048228
ET-ELT20
minimum
maximum
L (m) = (diagonal screen size in inches) × 0.061773 - 0.114022
L (m) = (diagonal screen size in inches) × 0.100725 - 0.112874
ET-ELT21
minimum
maximum
L (m) = (diagonal screen size in inches) × 0.100944 - 0.212284
L (m) = (diagonal screen size in inches) × 0.160333 - 0.210772
ET-ELW21
(fixed focus)
L (m) = (diagonal screen size in inches) × 0.017656 - 0.057678
Aspect ratio 16:9
• Distances calculated with the above equations will include a slight error.
As of July 2012
SFL12M004-2
9/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Shift range
Optical axis shift function allows to shift the position of a projected image as shown below.
H
(Width of
projected image)
0.1H
Standard postition
of projected image
0.6V
V
(Height of
projected image)
0.6V
0.1H
• The ET-ELW21 is a fixed short-focus lens. Therefore, the lens shift function provided in the main unit cannot be used.
Installable angle
Install the projector at an angle within the range shown below.
• Horizontal direction
The projector may be installed at a horizontal
angle of ±10°.
-10°+10°
360
°
• Vertical direction
The projector may be installed at a vertical
angle of 360°.
As of July 2012
SFL12M004-2
10/17
S
P
E
F
C
I
L
E
PT-EZ570/EZ570L
LCD Projectors
List of compatible signals
The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 kHz to 100 kHz (15 kHz to 120 kHz for RGB signals), vertical scanning frequencies of
24 Hz to 120 Hz (48 Hz to 100 Hz for RGB signals), and a dot clock of 162 MHz maximum (230 MHz
maximum for RGB signals) can be input.
NOTE:
The native resolution of this projector is 1,920 × 1,200 pixels. If the display resolution of the input signal is different from the
native resolution, image compression or expansion will be used to convert the input signal to a level within the native resolution.
Display mode
NTSC/NTSC4.43/PAL-M/PAL60
PAL/PAL-N/SECAM
480i (525i)
576i (625i)
480p (525p)
576p (625p)
480i (525i)
576i (625i)
480p (525p)
576p (625p)
720p
Display
resolution
(dots)*1
720 × 480i
720 × 576i
720 × 480i
720 × 576i
720 × 480i
720 × 576i
640 × 480i
768 × 576i
640 × 480
768 × 576
1280 × 720
1035i
1080i
1920 × 1035i
1920 × 1080i
1080p
1920 × 1080
1080psf/30
1080psf/25
1080psf/24
VGA
MAC LC13
MAC13
SVGA
MAC16
XGA
640 × 400
640 × 480
720 × 400
640 × 480
800 × 600
832 × 624
1024 × 768
1024 × 768i
MAC19
1024 × 768
Scanning frequency
H
V
(kHz)
(kHz)
15.7
15.6
15.7
15.6
31.5
31.3
15.7
15.6
31.5
31.3
37.5
45.0
33.8
28.1
33.8
27.0
28.1
33.8
56.3
67.5
33.8
28.1
27.0
31.5
31.5
37.5
37.9
37.9
43.3
31.5
35.0
35.0
32.7
34.5
35.2
37.9
37.9
38.0
38.6
46.9
48.1
53.7
49.7
43.4
44.0
46.9
47.0
48.4
48.5
58.0
56.5
60.0
60.3
61.0
62.0
63.5
68.7
35.5
36.0
60.2
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
59.9
50.0
50.0
60.0
60.0
50.0
60.0
24.0
25.0
30.0
50.0
60.0
60.0
50.0
48.0
70.1
59.9
75.0
72.8
74.4
85.0
70.1
66.6
66.7
51.1
55.4
56.3
60.3
61.0
60.5
60.3
75.0
72.2
85.1
74.6
60.1
54.6
58.2
58.3
60.0
60.0
72.0
70.1
75.0
74.9
75.7
77.1
79.4
85.0
87.0
87.2
75.1
Dot clock
frequency
(MHz)
Format
–
–
27.0
27.0
27.0
27.0
12.3
14.8
25.2
29.5
74.3
74.3
74.3
74.3
74.3
74.3
74.3
74.3
148.5
148.5
74.3
74.3
74.3
28.3
25.2
31.5
31.5
31.5
36.0
25.1
31.3
30.2
32.7
36.4
36.0
40.0
40.0
40.1
38.6
49.5
50.0
56.3
57.3
65.0
59.1
63.0
61.7
65.0
65.2
74.7
75.0
78.8
79.3
81.0
84.4
83.4
94.5
44.9
47.3
80.0
VIDEO/S-VIDEO
HDMI
HDMI/DVI-D
YP B P R /RGB
HDMI/DVI-D/
YP B P R /RGB
RGB
HDMI/DVI-D/RGB
RGB
HDMI/DVI-D/RGB
RGB
HDMI/DVI-D
RGB
* 1 The “i” appearing after the resolution indicates an interlaced signal.
As of July 2012
SFL12M004-2
11/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Display mode
WXGA
Display
resolution
(dots)*1
1280 × 768
1280 × 800
1360 × 768
MAC21
SXGA
1366
1376
1152
1152
×
×
×
×
768
768
870
900
1280 × 960
1280 × 1024
1280 × 1024i
MAC
SXGA+
1280 × 960
1280 × 1024
1400 × 1050
WXGA+
1440 × 900
UXGA
UXGA* 2
1600 × 1200
WSXGA+
WUXGA
WUXGA* 2
1680 × 1050
1920 × 1200
Scanning frequency
H
V
(kHz)
(kHz)
47.8
60.3
68.6
41.2
49.6
49.7
58.3
56.0
57.7
60.0
62.8
64.0
71.6
47.7
56.2
46.5
48.4
68.7
64.2
61.2
61.9
71.4
60.0
60.3
62.5
63.3
63.4
63.7
63.8
63.9
64.0
71.7
77.0
80.0
81.1
91.1
46.4
50.0
50.0
75.0
80.0
62.5
64.0
64.0
64.7
65.1
65.3
65.4
55.9
74.9
75.0
81.3
87.5
93.8
106.3
65.3
74.0
74.6
59.9
74.9
84.8
50.0
60.1
59.8
70.0
70.0
72.0
72.0
74.9
60.0
84.9
60.0
72.0
50.0
60.0
75.1
70.4
65.2
66.0
75.6
60.0
58.1
58.6
60.0
60.0
60.0
60.2
60.0
60.0
67.2
72.0
75.0
76.1
85.0
86.7
86.0
94.0
75.1
75.1
58.6
60.0
60.2
59.9
59.9
60.0
60.1
59.9
60.0
60.0
65.0
70.0
75.0
85.0
60.0
59.9
59.9
Dot clock
frequency
(MHz)
79.5
102.3
117.5
68.6
79.4
83.5
98.9
95.0
97.8
102.8
106.5
108.0
122.5
86.7
100.2
67.4
86.7
1000.0
94.6
92.0
94.5
105.1
108.0
93.1
108.0
108.2
111.5
109.5
108.2
107.4
108.0
117.0
130.1
135.0
135.0
157.5
78.7
80.0
80.0
126.0
135.2
108.0
108.2
108.0
101.0
122.4
121.8
122.9
106.5
161.9
162.0
175.5
189.0
202.5
229.5
146.3
154.0
193.3
Format
HDMI/DVI-D/RGB
HDMI/DVI-D
HDMI/DVI-D/RGB
RGB
HDMI/DVI-D
RGB
HDMI/DVI-D/RGB
RGB
HDMI/DVI-D/RGB
RGB
HDMI/DVI-D/RGB
RGB
HDMI/DVI-D/RGB
RGB
* 1 The “i” appearing after the resolution indicates an interlaced signal.
* 2 The “REAL” mode of “SCREEN” setting cannot be operated for these modes.
As of July 2012
SFL12M004-2
12/17
S
P
E
F
C
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below.
Pin assignments and signal names
6
No.
1
2
3
4
5
9
1
5
Signal name
–
TXD
RXD
–
GND
Description
NC
Transmitted data
Received data
Connected internally
Ground
No.
6
7
8
9
Signal name
–
CTS
RTS
–
Description
NC
Connected internally
Connected internally
NC
D-sub 9-pin (female) Serial input
Communication conditions (factory setting)
Signal level
Synchronization method
Baud rate
Parity
Character length
Stop bit
X parameter
S parameter
RS-232C-compliant
Start-stop synchronization
19,200 bps
None
8 bits
1 bit
None
None
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
STX
A
D
I1 I2
;
C1 C2 C3
Start
(2 byte)
Semicolon
(1 byte)
(1 byte)
ID: 2 characters
(2 bytes)
01 to 64: Address number
0A to 0Z: Group ID
ZZ: All units (ID ALL)
:
Colon
(1 byte)
P1 P2 ... Pn
ETX
End
(1 byte)
Parameters
(undefined length)
Command
(3 bytes)
(Control and/or query commands)
ID designator
CAUTION
• It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then try sending or receiving again.
• When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector before sending the next
command.
• Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for command response to 10
seconds or more.
• When using two or more units, set different IDs for each unit.
As of July 2012
SFL12M004-2
13/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Cable specifications
Projector
1
PC (DTE)
NC
NC
2
2
3
3
4
1
4
NC
NC
6
NC
NC
6
7
NC
NC
7
8
NC
NC
8
9
NC
NC
9
5
5
Control commands
*
Command : Parameter
Function
PON
POF
IIS:HD1
IIS:DVI
IIS:RG1
IIS:RG2
IIS:CP1
IIS:VD1
IIS:CP2
IIS:SVD
IIS:VD2
OLP:2
OLP:0
OLP:3
OLP:4
OSH:0
OSH:1
OFZ:1
OFZ:0
OAS
VSE:0
VSE:6
VSE:2
VSE:40
VSE:5
VSE:50
VPM:STD
VPM:DYN
VPM:CIN
VPM:REA
Standby power
Input selection
Lamp power
Shutter
Freeze
Callback
On
Off
Input 1 [HDMI]
Input 1 [DVI-D]
Input 1 [RGB (PC)]
Input 2 [RGB (PC)]
Input 2 [RGB (YPBPR/YCBCR)]
Input 2 [Video]
Input 3 [component]
Input 3 [S-Video]
Input 3 [Video]
Auto
Normal
Eco 1
Eco 2
Off
On
On
Off
Auto setup
Screen (aspect)
Picture
Normal
Full
Wide (16:9)
Zoom
Real
Custom
Standard
Dynamic
Cinema
Real
PON
POF
IIS:HD1
IIS:DVI
IIS:RG1
IIS:RG2
IIS:CP1
IIS:VD1
IIS:CP2
IIS:SVD
IIS:VD2
OLP:2
OLP:0
OLP:3
OLP:4
OSH:0
OSH:1
OFZ:1
OFZ:0
OAS
VSE:0
VSE:6
VSE:2
VSE:40
VSE:5
VSE:50
VPM:STD
VPM:DYN
VPM:CIN
VPM:REA
Do not send PON, POF or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement
cycle.
*
When a command that cannot be executed during standby mode is sent, the projector will send an ER401 command in reply.
As of July 2012
SFL12M004-2
14/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Status request commands
Command : Parameter
Q PW
Function
Main power status
Q IN
Input signal status
Q LP
Lamp power mode status
Q SH
Shutter function status
Q FZ
Freeze function status
Q SE
Aspect mode status
Q PM
Picture mode status
Q ST
Q $L:1
Q TM:0
Q TM:2
Projector run time
Lamp run time
Temperature status
Callback
000
001
HD1
DVI
RG1
RG2
CP1
VD1
CP2
SVD
VD2
2
0
3
4
0
1
0
1
0
6
2
40
5
50
0
6
STD
DYN
CIN
REA
p1p2p3p4p5
p1p2p3p4
p1p2p3p4/p5p6p7p8 * 1
p1p2p3p4/p5p6p7p8 * 1
Description
Off
On
Input 1 [HDMI]
Input 1 [DVI-D]
Input 1 [RGB (PC)]
Input 2 [RGB (PC)]
Input 2 [RGB (YPBPR/YCBCR)]
Input 2 [Video]
Input 3 [component]
Input 3 [S-Video]
Input 3 [Video]
Auto
Normal
Eco 1
Eco 2
Off
On
On
Off
Normal
Full
Wide (16:9)
Zoom
Real
Custom
Normal
Full
Standard
Dynamic
Cinema
Real
00000 – 99999 hours
0000 – 9999 hours
Air intake
Panel section
* 1 p1p2p3p4 = Celsius (°C), p5p6p7p8 = Fahrenheit (°F)
NOTE: If a wrong command is received, the projector will send an ER401 or ER402 command to the computer.
Command example
To set the shutter function on, send the command as shown below.
STX
ADZZ ;
Start
ID Address
Character code 02
ZZ: ID ALL
OSH
:
Command
1
ETX
Parameter
End
Character code 03
NOTE: When sending commands without parameters, a colon (:) is not necessary.
As of July 2012
SFL12M004-2
15/17
S
P
E
C
F
I
L
E
PT-EZ570/EZ570L
LCD Projectors
Notes on projector placement and operation
The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the
following precautions.
1.
Never place objects on top of the projector.
2.
Make sure there is an unobstructed space of 1,000 mm (3 feet 3 inches) or more around the projector’s exhaust openings.
3.
Do not stack projector units directly on top of one another for the purpose of multiple (stacked)
projection. When stacking projector units, be sure to provide the amount of space indicated below
between them. These space requirements also apply to installations where only one projector unit
is operating at one time and the other unit is used as a backup.
4.
Make sure that nothing blocks the projector’s air intake and exhaust openings. Also, install the projector so that cool or hot air from other air conditioning equipment does not flow directly toward
the projector’s air intake or exhaust openings.
5.
Do not install the projector in an enclosed space. If it is necessary to install it in an enclosed
space, add a separate ventilation system. If ventilation is insufficient, hot air will accumulate at the
intake opening. This may cause the projector’s protective circuit to interrupt projector operation.
6.
If the projector is installed in an enclosed space, ensure that the projector’s intake and exhaust
openings are not blocked. Take particular care to ensure that hot air from the exhaust openings is
not sucked into the intake openings.
7.
When installing the projector in any manner other than floor mounting with the adjuster legs, use
the five threaded ceiling mount holes (screw diameter: M6, projector interior thread length: 12 mm)
to secure the projector.
500 mm
(1 ft 8 in)
or more
1000 mm ( 3 ft 3 in)
or more
500 mm
(1 ft 8 in)
or more
1000 mm
( 3 ft 3 in)
or more
Do not stack projector
units directly on top of
one another.
Direction of air intake and exhaust
Intake
Exhaust
As of July 2012
SFL12M004-2
16/17
S
P
E
C
F
I
L
E
LCD Projectors
PT-EZ570/EZ570L
Operating the projector continuously
1.
If the projector is to be operated continuously 12 hours or more, lamp replacement cycle duration
becomes shorter.
2.
The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short
periods.
Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice.
Product availability differs depending on region and country. This product may be subject to export control regulations.
PJLink is a registered trademark, or a trademark application has been filed, in Japan, the United States, and other countries and regions.
All other trademarks are the property of their respective trademark owners.
As of July 2012
SFL12M004-2
17/17