INSTALLATION/OPERATION
TXB-S422
Translator Board
C657M-G (5/07)
Contents
Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Important Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Esprit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Spectra III/Spectra IV Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Spectra Mini Dome Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
ExSite Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
American Dynamics Camera Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
List of Illustrations
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Esprit System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
TXB-S422 DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the TXB-S422 into the Esprit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the Esprit Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fastening the Esprit Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
TXB-S422 DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Spectra III/Spectra IV Back Box Interconnect Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Spectra III/Spectra IV Back Box Circuit Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Spectra III Dome Drive DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Spectra IV Dome Drive DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Spectra III/Spectra IV Dome Drive Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Locating the Spectra Mini Dome DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TXB-S422 DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Removing the Mini Dome Cover and Shorting Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installing the TXB-S422 and Mini Dome Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
ExSite Spanner Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Removing the ExSite Pan and Tilt Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TXB-S422 DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installing the TXB-S422 into the ExSite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
List of Tables
A
B
C
D
2
Receiver Address Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Camera Assignments for AD2083-02 Series Translators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TXB-S422 DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SW1-1 and SW1-2 DIP Switch Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
36
42
42
C657M-G (5/07)
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Only use attachments/accessories specified by the manufacturer.
6. Installation should be done only by qualified personnel and conform to all local codes.
Only use replacement parts recommended by Pelco.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present within
this unit.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
C657M-G (5/07)
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
3
Regulatory Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve RadioTV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington
D.C. 20402.
Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can
void your authority to operate this equipment under Federal Communications Commission’s rules.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The materials used in the manufacture of this document and its components are compliant to the
requirements of Directive 2002/95/EC.
This equipment contains electrical or electronic components that must be recycled properly to
comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical
and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this
equipment.
4
C657M-G (5/07)
Important Notice
All companies make changes and improvements in their products on a regular basis. Because this product
is interfacing with equipment not manufactured by Pelco, the possibility exists that the interface protocols
have changed or are in a different configuration from earlier tested units; therefore, an incompatibility may
occur. The existence of prior successful installations indicates our intent to provide equipment compatible
with other manufacturers, but does not guarantee successful results without on-site integration testing.
Pelco recommends purchasing a single unit for bench testing before the purchase and installation of this
product in quantity. Should any problems occur, Pelco will provide on-site technical support (North
American installations only) to analyze the interface protocols of your system. We will typically schedule
this visit within one week of when the problem is reported to Pelco Technical Support. Pelco will endeavor,
at its expense, to correct the interface incompatibility within two weeks on a high priority basis. During
these visits, the end user must agree to give Pelco reasonable access to the system in order to study and
correct the protocol incompatibility.
In the unlikely event that Pelco is unable to make the translator work in the system, Pelco will accept the
return of any Pelco products associated with the translator and refund the amounts paid for these products
plus freight expenses. Because Pelco recommends a bench test prior to installation, Pelco will not be liable
for any installation costs or lost revenues in the event it cannot solve the compatibility problem.
C657M-G (5/07)
5
Description
The TXB-S422 translator board allows Sensormatic® controllers to communicate with Pelco’s ExSite™,
Esprit®, and Spectra® systems. Once installed the Spectra, ExSite, or Esprit system receives commands
from the Sensormatic controller and converts the commands into Pelco’s D protocol.
The TXB-S422 translator board has been tested and shown to work with the following Sensormatic
systems:
•
RC58 (VM1-SensorVision®)
•
RC216 (VM96-View Manager®)
•
AD2083-02 Series American Dynamics™ protocol translator
NOTE: The TXB-AD does not support SensorNet® code commands.
Parts List
The following items are supplied:
6
1
TXB-S422 translator board (printed circuit board)
1
6-32 screw with lock washer (for Spectra III™/Spectra IV Series only)
1
4-40 screw with lock washer (unused)
C657M-G (5/07)
Esprit Installation
To install the TXB-S422 translator board in an Esprit system (refer to Figure 1):
1. Turn off power to the Esprit system.
2. Remove the left cover from the pan and tilt.
3. Remove the shorting plug from the 16-pin connector on the Esprit system’s circuit board.
4. Remove the nut and washer from the standoff on the Esprit system’s circuit board.
NOTES:
•
Discard the 6-32 and 4-40 screws and their lock washers; they are not used in the Esprit system.
•
Save the 16-pin shorting plug. Otherwise, the Esprit cannot be converted back to a Pelco-controlled
system.
SW2 SW1
ON
OFF 1 2 3 4 5 6 7 8
ON
OFF 1 2 3 4 5 6 7 8
DIP SWITCHES
NYLON
WASHER
PHILLIPS
SCREW
ESPRIT CIRCUIT BOARD
16-PIN CONNECTOR
REMOVE SHORTING PLUG
STANDOFF WITH
NUT AND WASHER
Figure 1. Esprit System
C657M-G (5/07)
7
5. Set the proper termination setting on the DIP switch on the TXB-S422 (refer to Figure 2). Note the
following:
•
•
•
•
•
By default, the TXB-S422 termination is set to the ON position.
All TXB-S422s in a daisy chain, except the last unit, must be unterminated.
The total wire distance from the controller to the last TXB-S422 in a daisy chain must be less
than 4,000 ft (1,219 m).
A maximum of 10 receivers can be installed on a single daisy chain.
To unterminate a TXB-S422, change the termination setting on the DIP switch on the
TXB-S422 to the OFF position.
FRONT
BACK
DIP SWITCH
16-PIN CONNECTOR
Figure 2. TXB-S422 DIP Switch
6. Set the other DIP switches on the TXB-S422 translator board to the proper settings (refer to Table C
on page 42 of the Appendix for switch settings).
7. Install the TXB-S422 on the Esprit circuit board (refer to Figure 3):
a.
Insert the 16-pin connector on the bottom of the TXB-S422 into the mating 16-pin connector on
the Esprit circuit board.
b.
Reinstall the nut and washer on the standoff to secure the TXB-S422 to the Esprit circuit
board.
STANDOFF
16-PIN CONNECTOR
STANDOFF NUT
AND WASHER
Figure 3. Installing the TXB-S422 into the Esprit
8
C657M-G (5/07)
8. Set the DIP switches on the Esprit system (refer to Figure 1 on page 7 for switch location):
a.
SW1: Set all SW1 switches to the OFF position.
b.
SW2: Set the Esprit address (refer to Table A on page 29 of the Appendix for switch settings).
c.
For an American Dynamics protocol translator, refer to Table B on page 36 of the Appendix for
the receiver address.
9. Reinstall the left cover of the pan and tilt:
WARNING: Make sure you seal the unit. Otherwise, moisture could disable or damage the Esprit
system.
a.
Properly position the cover and slide it into place. The sides of the cover must fit under the
front and back rain guards of the pan and tilt. The top of the cover must seat against the lip of
the top gasket. (Refer to Figure 4.)
NOT SEALED
CORRECT
INCORRECT
GAP
Figure 4. Installing the Esprit Cover
C657M-G (5/07)
9
b.
Apply pressure and push the top of the cover down to align the screw holes (refer to Figure 5).
c.
Insert the Phillips screw and washer. Tighten until the screw will not turn.
TOP GASKET
FRONT
RAIN
GUARD
Figure 5. Fastening the Esprit Cover
10. Remove the pan and tilt from the base of the Esprit system.
10
C657M-G (5/07)
11. Check the control wiring inside the base of the unit. Refer to the Esprit documentation and the
documentation supplied with your controller to make sure the wiring is correct.
Sensormatic RC216
(422 Data Controller)
Esprit
Wire Harness
TX LO TX HI +
RX- (Green)
RX+ (Red)
RX LO RX HI +
TX- (Black)
TX+ (White)
RING
SLEEVE
Sensormatic RC58
DATA
OUT
TIP
USE A TWO-CONDUCTOR SHIELDED
CABLE WHERE THE SHIELD IS
CONNECTED TO THE SLEEVE.
DATA
IN
Tip
Esprit
Wire Harness
RX- (Green)
Ring
RX+ (Red)
Tip
TX- (Black)
Ring
TX+ (White)
AD2083/02 Controller
Esprit
Wire Harness
TT+
RX- (Green)
RX+ (Red)
RR+
TX- (Black)
TX+ (White)
12. Reattach the pan and tilt onto the base of the unit.
13. Apply power to the system. The following message appears on the monitor as soon as the Esprit
configuration cycle is completed:
TXB-S422 Rev x.xx yy
NOTE: x.xx represents the current firmware revision. yy represents the DIP switch selections for
TXB-S422.
C657M-G (5/07)
11
Spectra III/Spectra IV Installation
To install the TXB-S422 translator board in a Spectra III/Spectra IV Series:
1. Turn off power to the dome system.
2. Remove the lower dome.
3. Remove the dome drive by pressing in the blue and red tabs on the sides of the dome drive. Gently
rock the dome drive to release it from the back box.
4. Set the proper termination setting on the DIP switch on the TXB-S422 (refer to Figure 6). Note the
following:
•
•
•
•
•
By default, the TXB-S422 termination is set to the ON position.
All TXB-S422s in a daisy chain, except the last unit, must be unterminated.
The total wire distance from the controller to the last TXB-S422 in a daisy chain must be less
than 4,000 ft (1,219 m).
A maximum of 10 receivers can be installed on a single daisy chain.
To unterminate a TXB-S422, change the termination setting on the DIP switch on the
TXB-S422 to the OFF position.
FRONT
BACK
DIP SWITCH
16-PIN CONNECTOR
Figure 6. TXB-S422 DIP Switch
5. Set the other DIP switches on the TXB-S422 translator board to the proper settings (refer to Table C
on page 42 of the Appendix for switch settings).
12
C657M-G (5/07)
6. Install the TXB-S422 translator board into the back box:
a.
b.
Open the hinged door to the back box. Push the tab lock towards the back box wall of the unit
and open the door (refer to Figure 7).
Figure 7. Spectra III/Spectra IV Back Box Interconnect Door
Check the wiring to the controller. Refer to the Spectra III/Spectra IV documentation and the
documentation supplied with your controller to make sure the wiring is correct.
Sensormatic RC216
(422 Data Controller)
Spectra III/Spectra IV
Four-Wire Terminal Block
TX LO TX HI +
RXRX+
RX LO RX HI +
TXTX+
RING
SLEEVE
TIP
USE A TWO-CONDUCTOR SHIELDED
CABLE WHERE THE SHIELD IS
CONNECTED TO THE SLEEVE.
C657M-G (5/07)
Sensormatic RC58
Spectra III/Spectra IV
Four-Wire Terminal Block
DATA
OUT
Tip
RX-
Ring
RX+
DATA
IN
Tip
TX-
Ring
TX+
AD2083/02 Controller
Spectra III/Spectra IV
Four-Wire Terminal Block
TT+
RXRX+
RR+
TXTX+
13
c.
Remove the shorting plug from the 16-pin connector located on the back box circuit board
(refer to Figure 8).
6-32 SCREW AND
LOCK WASHER
REMOVE SHORTING
PLUG
16-PIN CONNECTOR
STANDOFF
Figure 8. Spectra III/Spectra IV Back Box Circuit Board
NOTES:
•
•
Discard the 4-40 screw and its lock washer; they are not used in the Spectra III/
Spectra IV system.
Save the 16-pin shorting plug. Otherwise, the Spectra III/Spectra IV cannot be converted
back to a Pelco-controlled system.
d.
Insert the TXB-S422 board into the 16-pin connector located on the back box circuit board.
Secure the translator board to the standoff on the circuit board using the supplied 6-32 screw
and lock washer.
e.
Close the interconnect door. Snap the tab lock into place.
7. Set the DIP switches on the Spectra III/Spectra IV system (refer to Figure 9 and Figure 10 on page 15
for switch locations):
a.
Set the SW1 switches on the dome drive to assign the Pelco D address (refer to Table A on
page 29 of the Appendix for switch settings).
b.
For Spectra III systems, set all SW3 switches on the dome drive to the OFF position.
For Spectra IV systems, set SW2-1 through SW2-8 to the OFF position.
c.
14
For an American Dynamics protocol translator, refer to Table B on page 36 of the Appendix for
the receiver address.
C657M-G (5/07)
SW1 SW3
SW2
SW1 AND SW2
1 2 3 4 5 6 7 8
1
1 2 3 4 5 6 7 8
SW1
SW3
on SW2 on
Figure 9. Spectra III Dome Drive
DIP Switches
Figure 10. Spectra IV Dome Drive
DIP Switches
8. Install the dome drive. Line up the blue (A) and red (B) tabs with the blue (A) and red (B) labels. When
pushing the tabs in, insert one side, then the other. Continue pushing on the ends of the tabs until
both tabs click into place. Refer to Figure 11.
NOTE: Refer to the installation manual supplied with the Spectra III/Spectra IV dome for
instructions on installing the back box, dome drive, and lower dome.
Figure 11. Spectra III/Spectra IV Dome Drive Installation
9. Install the lower dome.
10. Apply power to the system. The following message appears on the monitor as soon as the
Spectra III/Spectra IV configuration cycle is completed:
TXB-S422 Rev x.xx yy
NOTE: x.xx represents the current firmware revision. yy represents the DIP switch selections for
TXB-S422.
C657M-G (5/07)
15
Spectra Mini Dome Installation
To install the TXB-S422 translator board in a Spectra Mini dome:
NOTE: Installing a TXB-S422 into a mini dome increases unit height. In surface mount installations, you
must cut a hole in the surface to accommodate the TXB-S422 cover. For an installation template and more
information, refer to the Spectra Mini Dome Installation manual.
1. Turn off power to the dome system.
2. If the Spectra Mini dome is already installed, remove it to access the top of the dome drive where
the translator board will be installed.
3. Place the dome drive on a flat surface with the dome liner pointing up.
4. Set the DIP switches on the dome (refer to Figure 12 for switch location):
NOTE: There are no SW1 switch settings on the Spectra Mini dome.
a.
Point the camera straight up.
b.
Using a flashlight, look through the viewing slot of the dome liner. Rotate the dome liner until
you see two DIP switches in the bottom of the housing.
ON
SW 3
SW 2
ON
Figure 12. Locating the Spectra Mini Dome DIP Switches
16
C657M-G (5/07)
c.
SW2: Set all switches to the OFF position.
d.
SW3: Set the Spectra Mini dome address (refer to Table A on page 29 of the Appendix for
switch settings).
e.
For an American Dynamics protocol translator, refer to Table B on page 36 of the Appendix for
the receiver address.
5. Set the proper termination setting on the DIP switch on the TXB-S422 (refer to Figure 13). Note the
following:
•
•
•
•
•
By default, the TXB-S422 termination is set to the ON position.
All TXB-S422s in a daisy chain, except the last unit, must be unterminated.
The total wire distance from the controller to the last TXB-S422 in a daisy chain must be less
than 4,000 ft (1,219 m).
A maximum of 10 receivers can be installed on a single daisy chain.
To unterminate a TXB-S422, change the termination setting on the DIP switch on the
TXB-S422 to the OFF position.
FRONT
BACK
DIP SWITCH
16-PIN CONNECTOR
Figure 13. TXB-S422 DIP Switch
6. Set the other DIP switches on the TXB-S422 to the proper settings (refer to Table C on page 42 of the
Appendix for switch settings).
C657M-G (5/07)
17
7. Install the TXB-S422 translator board (refer to Figure 14 and Figure 15):
a.
Remove the cover from the top of the dome drive.
b.
Remove the shorting plug from the 16-pin connector located on the Spectra Mini dome circuit
board.
NOTES:
•
•
Discard the 4-40 and 6-32 screws and their lock washers; they are not used in the
Spectra Mini dome.
Save the 16-pin shorting plug and the original cover from the Spectra Mini dome.
Otherwise, the unit cannot be converted back to a Pelco-controlled system.
REMOVE
SHORTING
PLUG
Figure 14. Removing the Mini Dome Cover and Shorting Plug
18
C657M-G (5/07)
c.
Insert the TXB-S422 translator board into the 16-pin connector on the Spectra Mini dome’s
circuit board.
d.
Install the translator board cover that is supplied with the Spectra Mini dome.
Figure 15. Installing the TXB-S422 and Mini Dome Cover
C657M-G (5/07)
19
8. Check the wiring to the controller. Refer to the Spectra Mini dome documentation and the
documentation supplied with your controller to make sure the wiring is correct.
Sensormatic RC216
(422 Data Controller)
Spectra Mini Dome
RJ45-10 Connector
TX LO TX HI +
Pin 3 (RX-)
Pin 4 (RX+)
RX LO RX HI +
Pin 5 (TX-)
Pin 6 (TX+)
RING
SLEEVE
Sensormatic RC58
DATA
OUT
TIP
USE A TWO-CONDUCTOR SHIELDED
CABLE WHERE THE SHIELD IS
CONNECTED TO THE SLEEVE.
DATA
IN
Spectra Mini Dome
RJ45-10 Connector
Tip
Pin 3 (RX-)
Ring
Pin 4 (RX+)
Tip
Pin 5 (TX-)
Ring
Pin 6 (TX+)
AD2083/02 Controller
Spectra Mini Dome
RJ45-10 Connector
TT+
Pin 3 (RX-)
Pin 4 (RX+)
RR+
Pin 5 (TX-)
Pin 6 (TX+)
9. Refer to the installation manual for the Spectra Mini dome to complete the installation.
10. Apply power to the system. The following message appears on the monitor as soon as the Spectra
Mini dome configuration cycle is completed:
TXB-S422 Rev x.xx yy
NOTE: x.xx represents the current firmware revision. yy represents the DIP switch selections for
TXB-S422.
20
C657M-G (5/07)
ExSite Installation
To install the TXB-S422 translator board in an ExSite unit:
WARNING: To reduce the risk of ignition of hazardous atmospheres, disconnect the equipment
from the supply circuit before opening.
1. Turn off the power to the ExSite system.
WARNING: Total weight of the pan and tilt component is 55 pounds (25 kg). Use caution
when lifting and assembling the pan and tilt component on the power module. It is
recommended that nonslip gloves be worn during installation or removal.
2. Remove the pan and tilt unit from the power module (refer to Figure 16 and Figure 17):
a.
Loosen the setscrew in the locking ring with a 2 mm Allen wrench.
b.
Loosen the locking ring with a spanner wrench (Pelco part #MF00-1251-121A).
c.
Carefully unscrew the locking ring and remove the pan and tilt unit from the power module.
PAN AND
TILT UNIT
LOCKING
RING
Figure 16. ExSite Spanner Wrench
POWER
MODULE
Figure 17. Removing the ExSite Pan and Tilt Unit
C657M-G (5/07)
21
3. Set the proper termination setting on the DIP switch on the TXB-S422 (refer to Figure 18). Note the
following:
•
•
•
•
•
By default, the TXB-S422 termination is set to the ON position.
All TXB-S422s in a daisy chain, except the last unit, must be unterminated.
The total wire distance from the controller to the last TXB-S422 in a daisy chain must be less
than 4,000 ft (1,219 m).
A maximum of 10 receivers can be installed on a single daisy chain.
To unterminate a TXB-S422, change the termination setting on the DIP switch on the
TXB-S422 to the OFF position.
FRONT
BACK
DIP SWITCH
16-PIN CONNECTOR
Figure 18. TXB-S422 DIP Switch
4. Set the other DIP switches on the TXB-S422 translator board to the proper settings (refer to Table C
on page 42 of the Appendix for switch settings).
22
C657M-G (5/07)
5. Install the TXB-S422 board on the power module (refer to Figure 19):
a.
Remove the shorting plug from the 16-pin connector located on the ExSite’s circuit board.
NOTES:
•
•
b.
Discard the 4-40 and 6-32 screws and their lock washers; they are not used in the ExSite
system.
Save the 16-pin shorting plug. Otherwise, the ExSite cannot be converted back to a
Pelco-controlled system.
Insert the TXB-S422 board into the 16-pin connector located on the ExSite system’s circuit
board. Confirm that the TXB-S422 board is fully seated into the 16-pin connector.
16-PIN
CONNECTOR
SW1
SW3
Figure 19. Installing the TXB-S422 into the ExSite
C657M-G (5/07)
23
6. Check the wiring to the controller. Refer to the ExSite documentation and the documentation
supplied with your controller to make sure the wiring is correct.
Sensormatic RC216
(422 Data Controller)
ExSite
Wire Harness
TX LO TX HI +
Green (RX-)
Red (RX+)
RX LO RX HI +
White/Blue (TX-)
White/Orange (TX+)
RING
SLEEVE
Sensormatic RC58
DATA
OUT
TIP
Tip
ExSite
Wire Harness
Green (RX-)
Ring
Red (RX+)
Tip
White/Blue (TX-)
Ring
White/Orange (TX+)
USE A TWO-CONDUCTOR SHIELDED
CABLE WHERE THE SHIELD IS
CONNECTED TO THE SLEEVE.
DATA
IN
AD2083/02 Controller
ExSite
Wire Harness
TT+
Green (RX-)
Red (RX+)
RR+
White/Blue (TX-)
White/Orange (TX+)
7. Set the DIP switches on the ExSite system (refer to Figure 19 on page 23 for switch location):
a.
SW3: Verify that all SW3 switches on the ExSite power module are set to the OFF position.
b.
SW1: Set the ExSite address (refer to Table A on page 29 of the Appendix for switch settings).
c.
For an American Dynamics protocol translator, refer to Table B on page 36 of the Appendix for
the receiver address.
8. Attach the pan and tilt unit to the power module (refer to Figure 16 and Figure 17 on page 21):
a.
Align the pan and tilt unit with the power module. Carefully begin to hand-tighten the locking
ring onto the threads of the power module.
b.
Continue to tighten the locking ring with a spanner wrench.
c.
Tighten the setscrew in the locking ring with a 2 mm Allen wrench.
NOTE: Refer to the installation manual supplied with the ExSite system for instructions on
attaching the pan and tilt unit to the power module.
9. Apply power to the system. The following message appears on the monitor as soon as the ExSite
configuration cycle is completed:
TXB-S422 Rev x.xx yy
NOTE: x.xx represents the current firmware revision. yy represents the DIP switch selections for
TXB-S422.
24
C657M-G (5/07)
Operation
For detailed information about the operation of American Dynamics equipment, refer to Sensormatic
publication 8000-2692-13 “SpeedDome® Optima Programmable Dome Camera Quick Reference Guide,”
publication 8200-0184-02 “SpeedDome Ultra VII 22x Camera Dome Configuration Utility Operator’s
Manual,” and publication 8200-0184-04 “SpeedDome Ultra VII Day/Night Camera Dome Configuration
Utility Operator’s Manual.”
For copies of these documents, access American Dynamic’s Web site at www.americandynamics.net.
RC58–Controller Commands and System Response
RC58 Controller Commands
Pelco Unit Action
Pelco Controller
Commands
Pan, tilt, zoom, focus, and iris functions
Moves unit accordingly
Pan, tilt, zoom, focus, and
iris functions
Set 1-7 in Fixed Targets menu
Saves camera position as
preset 1-7
Set preset 1-7
1-7, TARGT key
Moves camera to preset
position 1-7
Call preset 1-7
Press and hold the Iris Close and Focus Near
keys and then press the Zoom Wide key.
Release all keys
Displays receiver
programming menu
Set preset 95
Hold the RAIL RIGHT key and press a
direction key (left, right, up, or down)
Increases pan/tilt speed 2X
Hold the FAST key and press a direction key
(left, right, up, or down)
Increases pan/tilt speed 3X
Hold the RAIL LEFT key and press a direction
key (left, right, up, or down)
Increases pan/tilt speed 4X
Press and hold the FAST and RAIL RIGHT keys Flip
C657M-G (5/07)
Call preset 33
25
RC216–Controller Commands and System Response
RC216
Controller Commands
Pelco Unit Action
Pelco Controller
Commands
Pan, tilt, zoom, focus, and iris functions
Moves unit accordingly
Pan, tilt, zoom, focus, and
iris functions
Refer to the manual supplied with controller
for instructions on how to program quick
views (presets)
Saves camera position as
preset 1-64
Set preset 1-64
1-64, VIEW key
Moves camera to preset
position 1-64
Call preset 1-64
Press and hold the Iris Open and Focus Near
keys and then press the Zoom Wide key.
Release all keys
Displays receiver
programming menu
Set preset 95
Refer to the manual supplied with controller
for instructions on how to program patterns
Defines pattern 1
Defines pattern 2
Defines pattern 3
1, PATRN key
Starts pattern 1
2, PATRN key
Starts pattern 2
3, PATRN key
Starts pattern 3
D key
Flip
Call preset 33
Refer to the manual supplied with the Touch Controls auxiliary outputs 1
Tracker Controller for instructions on how to and 2
program system activities for camera outputs
1 and 2
26
C657M-G (5/07)
AD2083-02 Series–Controller Commands and System Response
AD2083-02 Series
Controller Commands
Pelco Unit Action
Pelco Controller
Commands
Pan, tilt, zoom, focus, and iris functions
Moves unit accordingly
Pan, tilt, zoom, focus, and
iris functions
1-16, PRESET SET key
Saves camera position as
preset 1-16
Set preset 1-16
1-16, PRESET CALL key
Moves camera to preset
position 1-16
Call preset 1-16
17, PRESET SET key
Define patterns 1
18, PRESET SET key
Define patterns 2
19, PRESET SET key
Define patterns 3
33, PRESET SET key
Ends pattern programming
17, 21 or 25, PRESET CALL key
Starts pattern 1
18, 22 or 26, PRESET CALL key
Starts pattern 2
19, 23 or 27, PRESET CALL key
Starts pattern 3
40, PRESET CALL key
Flip
Press and hold the Iris Open and Focus Near Displays program menu
keys. Then press the Zoom Wide key. Release
all keys
1 or 2 Auxiliary ON*
Enables selected Auxiliary
control
1 or 2 Auxiliary OFF
Disables selected Auxiliary
control
Call preset 33
Set preset 95
*If an auxiliary is ON, it must be turned off before it can be activated a second time.
AMERICAN DYNAMICS CAMERA ASSIGNMENTS
Refer to Table B on page 36 in the Appendix for the receiver (Esprit, ExSite, or Spectra system) address
settings when using an AD2083-02 Series protocol translator. Refer to the American Dynamics AD2083
manual for instructions on how to configure the code translator’s camera block assignments.
C657M-G (5/07)
27
Troubleshooting
Symptom
No video.
Possible Cause
Power is not connected to the
Pelco unit.
Suggested Remedy
Check the power connector.
Video cable is not connected to Check the video connector.
the Pelco unit.
Translator board is not inserted Reinstall the translator board.
properly.
Make sure the pins on the
board are inserted correctly.
Pelco unit information (model, The Pelco unit cannot complete Refer to the troubleshooting
firmware, Pelco P and D
its configuration cycle.
section of the product manual
addresses, and communication
for the Pelco unit.
settings) does not appear after
the configuration cycle.
The message “TXB-S422
Rev x.xx yy” does not appear.
The baud rate setting on the
Pelco unit is not correct. The
setting appears on power-up.
The Pelco unit does not
respond to commands.
The unit address is not correct. Make sure the Pelco unit
(receiver) address is correct.
This address can range from 1
to 255.
Make sure the baud rate
setting on the Pelco unit is
2400. Then cycle device power.
Make sure the controller is
addressing the correct Pelco
unit.
The receiving and transmitting
lines are not connected
properly.
Make sure the TX+, TX-, RX+,
and RX- lines are properly
connected. (Refer to the wiring
tables in this manual as well
as the troubleshooting section
of the product manual for the
controller.)
The command was lost
Retry the command.
between the controller and the
Pelco unit.
28
C657M-G (5/07)
Appendix
Table A. Receiver Address Settings
Switch Setting
Receiver
Address
1
2
3
4
5
6
7
8
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
4
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
6
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
7
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
8
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
9
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
10
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
11
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
12
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
13
ON
OFF
ON
ON
OFF
OFF
OFF
OFF
14
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
15
ON
ON
ON
ON
OFF
OFF
OFF
OFF
16
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
17
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
18
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
19
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
20
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
21
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
22
OFF
ON
ON
OFF
ON
OFF
OFF
OFF
23
ON
ON
ON
OFF
ON
OFF
OFF
OFF
24
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
25
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
26
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
27
ON
ON
OFF
ON
ON
OFF
OFF
OFF
28
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
29
ON
OFF
ON
ON
ON
OFF
OFF
OFF
30
OFF
ON
ON
ON
ON
OFF
OFF
OFF
31
ON
ON
ON
ON
ON
OFF
OFF
OFF
32
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
33
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
34
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
35
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
36
OFF
OFF
ON
OFF
OFF
ON
OFF
OFF
37
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
C657M-G (5/07)
29
Table A. Receiver Address Settings (Continued)
30
Switch Setting
Receiver
Address
1
2
3
4
5
6
7
8
38
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
39
ON
ON
ON
OFF
OFF
ON
OFF
OFF
40
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
41
ON
OFF
OFF
ON
OFF
ON
OFF
OFF
42
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
43
ON
ON
OFF
ON
OFF
ON
OFF
OFF
44
OFF
OFF
ON
ON
OFF
ON
OFF
OFF
45
ON
OFF
ON
ON
OFF
ON
OFF
OFF
46
OFF
ON
ON
ON
OFF
ON
OFF
OFF
47
ON
ON
ON
ON
OFF
ON
OFF
OFF
48
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
49
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
50
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
51
ON
ON
OFF
OFF
ON
ON
OFF
OFF
52
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
53
ON
OFF
ON
OFF
ON
ON
OFF
OFF
54
OFF
ON
ON
OFF
ON
ON
OFF
OFF
55
ON
ON
ON
OFF
ON
ON
OFF
OFF
56
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
57
ON
OFF
OFF
ON
ON
ON
OFF
OFF
58
OFF
ON
OFF
ON
ON
ON
OFF
OFF
59
ON
ON
OFF
ON
ON
ON
OFF
OFF
60
OFF
OFF
ON
ON
ON
ON
OFF
OFF
61
ON
OFF
ON
ON
ON
ON
OFF
OFF
62
OFF
ON
ON
ON
ON
ON
OFF
OFF
63
ON
ON
ON
ON
ON
ON
OFF
OFF
64
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
65
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
66
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
67
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
68
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
69
ON
OFF
ON
OFF
OFF
OFF
ON
OFF
70
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
71
ON
ON
ON
OFF
OFF
OFF
ON
OFF
72
OFF
OFF
OFF
ON
OFF
OFF
ON
OFF
73
ON
OFF
OFF
ON
OFF
OFF
ON
OFF
74
OFF
ON
OFF
ON
OFF
OFF
ON
OFF
75
ON
ON
OFF
ON
OFF
OFF
ON
OFF
76
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
77
ON
OFF
ON
ON
OFF
OFF
ON
OFF
C657M-G (5/07)
Table A. Receiver Address Settings (Continued)
Switch Setting
Receiver
Address
1
2
3
4
5
6
7
8
78
OFF
ON
ON
ON
OFF
OFF
ON
OFF
79
ON
ON
ON
ON
OFF
OFF
ON
OFF
80
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
81
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
82
OFF
ON
OFF
OFF
ON
OFF
ON
OFF
83
ON
ON
OFF
OFF
ON
OFF
ON
OFF
84
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
85
ON
OFF
ON
OFF
ON
OFF
ON
OFF
86
OFF
ON
ON
OFF
ON
OFF
ON
OFF
87
ON
ON
ON
OFF
ON
OFF
ON
OFF
88
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
89
ON
OFF
OFF
ON
ON
OFF
ON
OFF
90
OFF
ON
OFF
ON
ON
OFF
ON
OFF
91
ON
ON
OFF
ON
ON
OFF
ON
OFF
92
OFF
OFF
ON
ON
ON
OFF
ON
OFF
93
ON
OFF
ON
ON
ON
OFF
ON
OFF
94
OFF
ON
ON
ON
ON
OFF
ON
OFF
95
ON
ON
ON
ON
ON
OFF
ON
OFF
96
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
97
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
98
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
99
ON
ON
OFF
OFF
OFF
ON
ON
OFF
100
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
101
ON
OFF
ON
OFF
OFF
ON
ON
OFF
102
OFF
ON
ON
OFF
OFF
ON
ON
OFF
103
ON
ON
ON
OFF
OFF
ON
ON
OFF
104
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
105
ON
OFF
OFF
ON
OFF
ON
ON
OFF
106
OFF
ON
OFF
ON
OFF
ON
ON
OFF
107
ON
ON
OFF
ON
OFF
ON
ON
OFF
108
OFF
OFF
ON
ON
OFF
ON
ON
OFF
109
ON
OFF
ON
ON
OFF
ON
ON
OFF
110
OFF
ON
ON
ON
OFF
ON
ON
OFF
111
ON
ON
ON
ON
OFF
ON
ON
OFF
112
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
113
ON
OFF
OFF
OFF
ON
ON
ON
OFF
114
OFF
ON
OFF
OFF
ON
ON
ON
OFF
115
ON
ON
OFF
OFF
ON
ON
ON
OFF
116
OFF
OFF
ON
OFF
ON
ON
ON
OFF
117
ON
OFF
ON
OFF
ON
ON
ON
OFF
C657M-G (5/07)
31
Table A. Receiver Address Settings (Continued)
32
Switch Setting
Receiver
Address
1
2
3
4
5
6
7
8
118
OFF
ON
ON
OFF
ON
ON
ON
OFF
119
ON
ON
ON
OFF
ON
ON
ON
OFF
120
OFF
OFF
OFF
ON
ON
ON
ON
OFF
121
ON
OFF
OFF
ON
ON
ON
ON
OFF
122
OFF
ON
OFF
ON
ON
ON
ON
OFF
123
ON
ON
OFF
ON
ON
ON
ON
OFF
124
OFF
OFF
ON
ON
ON
ON
ON
OFF
125
ON
OFF
ON
ON
ON
ON
ON
OFF
126
OFF
ON
ON
ON
ON
ON
ON
OFF
127
ON
ON
ON
ON
ON
ON
ON
OFF
128
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
129
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
130
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
131
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
132
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
133
ON
OFF
ON
OFF
OFF
OFF
OFF
ON
134
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
135
ON
ON
ON
OFF
OFF
OFF
OFF
ON
136
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
137
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
138
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
139
ON
ON
OFF
ON
OFF
OFF
OFF
ON
140
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
141
ON
OFF
ON
ON
OFF
OFF
OFF
ON
142
OFF
ON
ON
ON
OFF
OFF
OFF
ON
143
ON
ON
ON
ON
OFF
OFF
OFF
ON
144
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
145
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
146
OFF
ON
OFF
OFF
ON
OFF
OFF
ON
147
ON
ON
OFF
OFF
ON
OFF
OFF
ON
148
OFF
OFF
ON
OFF
ON
OFF
OFF
ON
149
ON
OFF
ON
OFF
ON
OFF
OFF
ON
150
OFF
ON
ON
OFF
ON
OFF
OFF
ON
151
ON
ON
ON
OFF
ON
OFF
OFF
ON
152
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
153
ON
OFF
OFF
ON
ON
OFF
OFF
ON
154
OFF
ON
OFF
ON
ON
OFF
OFF
ON
155
ON
ON
OFF
ON
ON
OFF
OFF
ON
156
OFF
OFF
ON
ON
ON
OFF
OFF
ON
157
ON
OFF
ON
ON
ON
OFF
OFF
ON
C657M-G (5/07)
Table A. Receiver Address Settings (Continued)
Switch Setting
Receiver
Address
1
2
3
4
5
6
7
8
158
OFF
ON
ON
ON
ON
OFF
OFF
ON
159
ON
ON
ON
ON
ON
OFF
OFF
ON
160
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
161
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
162
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
163
ON
ON
OFF
OFF
OFF
ON
OFF
ON
164
OFF
OFF
ON
OFF
OFF
ON
OFF
ON
165
ON
OFF
ON
OFF
OFF
ON
OFF
ON
166
OFF
ON
ON
OFF
OFF
ON
OFF
ON
167
ON
ON
ON
OFF
OFF
ON
OFF
ON
168
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
169
ON
OFF
OFF
ON
OFF
ON
OFF
ON
170
OFF
ON
OFF
ON
OFF
ON
OFF
ON
171
ON
ON
OFF
ON
OFF
ON
OFF
ON
172
OFF
OFF
ON
ON
OFF
ON
OFF
ON
173
ON
OFF
ON
ON
OFF
ON
OFF
ON
174
OFF
ON
ON
ON
OFF
ON
OFF
ON
175
ON
ON
ON
ON
OFF
ON
OFF
ON
176
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
177
ON
OFF
OFF
OFF
ON
ON
OFF
ON
178
OFF
ON
OFF
OFF
ON
ON
OFF
ON
179
ON
ON
OFF
OFF
ON
ON
OFF
ON
180
OFF
OFF
ON
OFF
ON
ON
OFF
ON
181
ON
OFF
ON
OFF
ON
ON
OFF
ON
182
OFF
ON
ON
OFF
ON
ON
OFF
ON
183
ON
ON
ON
OFF
ON
ON
OFF
ON
184
OFF
OFF
OFF
ON
ON
ON
OFF
ON
185
ON
OFF
OFF
ON
ON
ON
OFF
ON
186
OFF
ON
OFF
ON
ON
ON
OFF
ON
187
ON
ON
OFF
ON
ON
ON
OFF
ON
188
OFF
OFF
ON
ON
ON
ON
OFF
ON
189
ON
OFF
ON
ON
ON
ON
OFF
ON
190
OFF
ON
ON
ON
ON
ON
OFF
ON
191
ON
ON
ON
ON
ON
ON
OFF
ON
192
OFF
OFF
OFF
OFF
OFF
OFF
ON
ON
193
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
194
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
195
ON
ON
OFF
OFF
OFF
OFF
ON
ON
196
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
197
ON
OFF
ON
OFF
OFF
OFF
ON
ON
C657M-G (5/07)
33
Table A. Receiver Address Settings (Continued)
34
Switch Setting
Receiver
Address
1
2
3
4
5
6
7
8
198
OFF
ON
ON
OFF
OFF
OFF
ON
ON
199
ON
ON
ON
OFF
OFF
OFF
ON
ON
200
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
201
ON
OFF
OFF
ON
OFF
OFF
ON
ON
202
OFF
ON
OFF
ON
OFF
OFF
ON
ON
203
ON
ON
OFF
ON
OFF
OFF
ON
ON
204
OFF
OFF
ON
ON
OFF
OFF
ON
ON
205
ON
OFF
ON
ON
OFF
OFF
ON
ON
206
OFF
ON
ON
ON
OFF
OFF
ON
ON
207
ON
ON
ON
ON
OFF
OFF
ON
ON
208
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
209
ON
OFF
OFF
OFF
ON
OFF
ON
ON
210
OFF
ON
OFF
OFF
ON
OFF
ON
ON
211
ON
ON
OFF
OFF
ON
OFF
ON
ON
212
OFF
OFF
ON
OFF
ON
OFF
ON
ON
213
ON
OFF
ON
OFF
ON
OFF
ON
ON
214
OFF
ON
ON
OFF
ON
OFF
ON
ON
215
ON
ON
ON
OFF
ON
OFF
ON
ON
216
OFF
OFF
OFF
ON
ON
OFF
ON
ON
217
ON
OFF
OFF
ON
ON
OFF
ON
ON
218
OFF
ON
OFF
ON
ON
OFF
ON
ON
219
ON
ON
OFF
ON
ON
OFF
ON
ON
220
OFF
OFF
ON
ON
ON
OFF
ON
ON
221
ON
OFF
ON
ON
ON
OFF
ON
ON
222
OFF
ON
ON
ON
ON
OFF
ON
ON
223
ON
ON
ON
ON
ON
OFF
ON
ON
224
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
225
ON
OFF
OFF
OFF
OFF
ON
ON
ON
226
OFF
ON
OFF
OFF
OFF
ON
ON
ON
227
ON
ON
OFF
OFF
OFF
ON
ON
ON
228
OFF
OFF
ON
OFF
OFF
ON
ON
ON
229
ON
OFF
ON
OFF
OFF
ON
ON
ON
230
OFF
ON
ON
OFF
OFF
ON
ON
ON
231
ON
ON
ON
OFF
OFF
ON
ON
ON
232
OFF
OFF
OFF
ON
OFF
ON
ON
ON
233
ON
OFF
OFF
ON
OFF
ON
ON
ON
234
OFF
ON
OFF
ON
OFF
ON
ON
ON
235
ON
ON
OFF
ON
OFF
ON
ON
ON
236
OFF
OFF
ON
ON
OFF
ON
ON
ON
237
ON
OFF
ON
ON
OFF
ON
ON
ON
C657M-G (5/07)
Table A. Receiver Address Settings (Continued)
Switch Setting
Receiver
Address
1
2
3
4
5
6
7
8
238
OFF
ON
ON
ON
OFF
ON
ON
ON
239
ON
ON
ON
ON
OFF
ON
ON
ON
240
OFF
OFF
OFF
OFF
ON
ON
ON
ON
241
ON
OFF
OFF
OFF
ON
ON
ON
ON
242
OFF
ON
OFF
OFF
ON
ON
ON
ON
243
ON
ON
OFF
OFF
ON
ON
ON
ON
244
OFF
OFF
ON
OFF
ON
ON
ON
ON
245
ON
OFF
ON
OFF
ON
ON
ON
ON
246
OFF
ON
ON
OFF
ON
ON
ON
ON
247
ON
ON
ON
OFF
ON
ON
ON
ON
248
OFF
OFF
OFF
ON
ON
ON
ON
ON
249
ON
OFF
OFF
ON
ON
ON
ON
ON
250
OFF
ON
OFF
ON
ON
ON
ON
ON
251
ON
ON
OFF
ON
ON
ON
ON
ON
252
OFF
OFF
ON
ON
ON
ON
ON
ON
253
ON
OFF
ON
ON
ON
ON
ON
ON
254
OFF
ON
ON
ON
ON
ON
ON
ON
255
ON
ON
ON
ON
ON
ON
ON
ON
C657M-G (5/07)
35
Each AD (American Dynamics) group has its own communication line that can control 99 devices. Use
Table A and Table B to identify the DIP switch settings for the receiver:
1. Find the AD group for the desired camera number. For example, camera 499 is located in AD group 5.
2. Locate the receiver address for the camera number in the far right column. In this example, the
receiver address is 4 for camera 499.
3. Find the receiver address in column 1 of Table A.
4. Identify the proper DIP switch settings for the Pelco unit. In this example, the receiver address is 4
and SW1-SW8 are OFF, OFF, ON, OFF, OFF, OFF, OFF, OFF.
Table B. Camera Assignments for AD2083-02 Series Translators
36
AD Group 0
AD Group 1
AD Group 2
AD Group 3
AD Group 4
AD Group 5
Receiver
Address
1
100
199
298
397
496
1
2
101
200
299
398
497
2
3
102
201
300
399
498
3
4
103
202
301
400
499
4
5
104
203
302
401
500
5
6
105
204
303
402
501
6
7
106
205
304
403
502
7
8
107
206
305
404
503
8
9
108
207
306
405
504
9
10
109
208
307
406
505
10
11
110
209
308
407
506
11
12
111
210
309
408
507
12
13
112
211
310
409
508
13
14
113
212
311
410
509
14
15
114
213
312
411
510
15
16
115
214
313
412
511
16
17
116
215
314
413
512
17
18
117
216
315
414
513
18
19
118
217
316
415
514
19
20
119
218
317
416
515
20
21
120
219
318
417
516
21
22
121
220
319
418
517
22
23
122
221
320
419
518
23
24
123
222
321
420
519
24
25
124
223
322
421
520
25
26
125
224
323
422
521
26
27
126
225
324
423
522
27
28
127
226
325
424
523
28
29
128
227
326
425
524
29
30
129
228
327
426
525
30
31
130
229
328
427
526
31
32
131
230
329
428
527
32
C657M-G (5/07)
Table B. Camera Assignments for AD2083-02 Series Translators (Continued)
AD Group 0
AD Group 1
AD Group 2
AD Group 3
AD Group 4
AD Group 5
Receiver
Address
33
132
231
330
429
528
33
34
133
232
331
430
529
34
35
134
233
332
431
530
35
36
135
234
333
432
531
36
37
136
235
334
433
532
37
38
137
236
335
434
533
38
39
138
237
336
435
534
39
40
139
238
337
436
535
40
41
140
239
338
437
536
41
42
141
240
339
438
537
42
43
142
241
340
439
538
43
44
143
242
341
440
539
44
45
144
243
342
441
540
45
46
145
244
343
442
541
46
47
146
245
344
443
542
47
48
147
246
345
444
543
48
49
148
247
346
445
544
49
50
149
248
347
446
545
50
51
150
249
348
447
546
51
52
151
250
349
448
547
52
53
152
251
350
449
548
53
54
153
252
351
450
549
54
55
154
253
352
451
550
55
56
155
254
353
452
551
56
57
156
255
354
453
552
57
58
157
256
355
454
553
58
59
158
257
356
455
554
59
60
159
258
357
456
555
60
61
160
259
358
457
556
61
62
161
260
359
458
557
62
63
162
261
360
459
558
63
64
163
262
361
460
559
64
65
164
263
362
461
560
65
66
165
264
363
462
561
66
67
166
265
364
463
562
67
68
167
266
365
464
563
68
69
168
267
366
465
564
69
70
169
268
367
466
565
70
71
170
269
368
467
566
71
72
171
270
369
468
567
72
C657M-G (5/07)
37
Table B. Camera Assignments for AD2083-02 Series Translators (Continued)
38
AD Group 0
AD Group 1
AD Group 2
AD Group 3
AD Group 4
AD Group 5
Receiver
Address
73
172
271
370
469
568
73
74
173
272
371
470
569
74
75
174
273
372
471
570
75
76
175
274
373
472
571
76
77
176
275
374
473
572
77
78
177
276
375
474
573
78
79
178
277
376
475
574
79
80
179
278
377
476
575
80
81
180
279
378
477
576
81
82
181
280
379
478
577
82
83
182
281
380
479
578
83
84
183
282
381
480
579
84
85
184
283
382
481
580
85
86
185
284
383
482
581
86
87
186
285
384
483
582
87
88
187
286
385
484
583
88
89
188
287
386
485
584
89
90
189
288
387
486
585
90
91
190
289
388
487
586
91
92
191
290
389
488
587
92
93
192
291
390
489
588
93
94
193
292
391
490
589
94
95
194
293
392
491
590
95
96
195
294
393
492
591
96
97
196
295
394
493
592
97
98
197
296
395
494
593
98
99
198
297
396
495
594
99
C657M-G (5/07)
Table B. Camera Assignments for AD2083-02 Series Translators (Continued)
AD Group 6
AD Group 7
AD Group 8
AD Group 9
AD Group 10
Receiver
Address
595
694
793
892
991
1
596
695
794
893
992
2
597
696
795
894
993
3
598
697
796
895
994
4
599
698
797
896
995
5
600
699
798
897
996
6
601
700
799
898
997
7
602
701
800
899
998
8
603
702
801
900
999
9
604
703
802
901
1000
10
605
704
803
902
1001
11
606
705
804
903
1002
12
607
706
805
904
1003
13
608
707
806
905
1004
14
609
708
807
906
1005
15
610
709
808
907
1006
16
611
710
809
908
1007
17
612
711
810
909
1008
18
613
712
811
910
1009
19
614
713
812
911
1010
20
615
714
813
912
1011
21
616
715
814
913
1012
22
617
716
815
914
1013
23
618
717
816
915
1014
24
619
718
817
916
1015
25
620
719
818
917
1016
26
621
720
819
918
1017
27
622
721
820
919
1018
28
623
722
821
920
1019
29
624
723
822
921
1020
30
625
724
823
922
1021
31
626
725
824
923
1022
32
627
726
825
924
1023
33
628
727
826
925
1024
34
629
728
827
926
1025
35
630
729
828
927
1026
36
631
730
829
928
1027
37
632
731
830
929
1028
38
633
732
831
930
1029
39
634
733
832
931
1030
40
C657M-G (5/07)
39
Table B. Camera Assignments for AD2083-02 Series Translators (Continued)
40
AD Group 6
AD Group 7
AD Group 8
AD Group 9
AD Group 10
Receiver
Address
635
734
833
932
1031
41
636
735
834
933
1032
42
637
736
835
934
1033
43
638
737
836
935
1034
44
639
738
837
936
1035
45
640
739
838
937
1036
46
641
740
839
938
1037
47
642
741
840
939
1038
48
643
742
841
940
1039
49
644
743
842
941
1040
50
645
744
843
942
1041
51
646
745
844
943
1042
52
647
746
845
944
1043
53
648
747
846
945
1044
54
649
748
847
946
1045
55
650
749
848
947
1046
56
651
750
849
948
1047
57
652
751
850
949
1048
58
653
752
851
950
1049
59
654
753
852
951
1050
60
655
754
853
952
1051
61
656
755
854
953
1052
62
657
756
855
954
1053
63
658
757
856
955
1054
64
659
758
857
956
1055
65
660
759
858
957
1056
66
661
760
859
958
1057
67
662
761
860
959
1058
68
663
762
861
960
1059
69
664
763
862
961
1060
70
665
764
863
962
1061
71
666
765
864
963
1062
72
667
766
865
964
1063
73
668
767
866
965
1064
74
669
768
867
966
1065
75
670
769
868
967
1066
76
671
770
869
968
1067
77
672
771
870
969
1068
78
673
772
871
970
1069
79
674
773
872
971
1070
80
C657M-G (5/07)
Table B. Camera Assignments for AD2083-02 Series Translators (Continued)
AD Group 6
AD Group 7
AD Group 8
AD Group 9
AD Group 10
Receiver
Address
675
774
873
972
1071
81
676
775
874
973
1072
82
677
776
875
974
1073
83
678
777
876
975
1074
84
679
778
877
976
1075
85
680
779
878
977
1076
86
681
780
879
978
1077
87
682
781
880
979
1078
88
683
782
881
980
1079
89
684
783
882
981
1080
90
685
784
883
982
1081
91
686
785
884
983
1082
92
687
786
885
984
1083
93
688
787
886
985
1084
94
689
788
887
986
1085
95
690
789
888
987
1086
96
691
790
889
988
1087
97
692
791
890
989
1088
98
693
792
891
990
1089
99
C657M-G (5/07)
41
Table C. TXB-S422 DIP Switch Settings
Switch
Position
Function
1 and 2
Refer to Table D
3
ON
Sets the response delay to fast (SpeedDome Ultra speed)
OFF
Default setting. Sets the response delay to slow (SpeedDome
speed)
Pan and tilt speed setting or CPU type
4
OFF
Always OFF
5
ON
Enables receiver address 64
OFF
Disables receiver address 64 (Sensormatic default)
ON
Esprit setting
OFF
Spectra III/Spectra IV, Spectra Mini dome, and ExSite setting
6
7 and 8
ON
Terminates communication line
OFF
Unterminates communication line
Table D. SW1-1 and SW1-2 DIP Switch Settings
Switch
Use
SW1-1
Select CPU type or
speed control
ON
Selects RC58 and RC216
OFF
Speed control for RC58 and RC216
Speed control
ON
Half speed
OFF
Full speed
SW1-2
Position
Function
REVISION HISTORY
Manual #
C657M
C657M-A
C657M-B
C657M-C
C657M-D
Date
6/02
7/02
8/02
10/02
12/03
C657M-E
C657M-F
C657M-G
3/05
3/06
5/07
42
Comments
Original version.
Speed settings applicable only for Sensormatic RC216 Matrix.
Revised operation instructions.
Revised per ECO 02-8063.
Revised per ECO 03-9431: Added material about the use of DIP switches 1 and 2 with American Dynamics
AD1024 CPU. Removed material about the use of these DIP switches with Sensormatic equipment.
Added installation instructions for ExSite explosionproof system.
Added Spectra Mini dome. Removed Spectra II. Updated graphics and procedures.
Added RoHS Directive, cross references, and Spectra IV.
C657M-G (5/07)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.
Exceptions to this warranty are as noted below:
• Five years on fiber optic products and TW3000 Series unshielded twisted pair transmission products.
• Three years on Spectra® IV products.
• Three years on Genex® Series products (multiplexers, server, and keyboard).
• Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and
MC3651H-2X camera models, which have a five-year warranty.
• Three years on PMCL200/300/400 Series LCD monitors.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.
• Two years on Spectra III™, Esprit®, ExSite®, and PS20 scanners, including when used in continuous motion applications.
• Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).
• Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of
90 days. The air filter is not covered under warranty.
• Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura™ Series distributed network-based video
products.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this
warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization
number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate
address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the
following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Pelco, the Pelco logo, Camclosure, Esprit, ExSite, Genex, Legacy, and Spectra are registered trademarks of Pelco.
©Copyright 2007, Pelco.
Endura and Spectra III are trademarks of Pelco.
All rights reserved.
DLP is a registered trademark of Texas Instruments, Inc.
Sensormatic, SensorNet, SensorVision, View Manager, and SpeedDome are registered trademarks of Sensormatic Electronics Corporation.
American Dynamics is a trademark of Sensormatic Electronics Corporation.
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
www.pelco.com
ISO9001
Australia
| Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore
| Spain | Sweden | United Arab Emirates | United Kingdom | United States
South Africa