Data sheet
HP 5820 Switch Series
Key features
•For enterprise edge, or distribution/data center
•Up to 24 ports of 10GbE per unit/194 per stack
•Flex chassis—modular resiliency
•Cut-through switching for very low latency
•Hot-swappable I/O, power supplies, and fans
Product overview
HP 5820 Switch Series supports advanced features that deliver a unique combination of
unmatched 10 Gigabit Ethernet; high-availability architecture; full Layer 2/3 dual-stack IPv4/IPv6;
and line-rate, low-latency performance on all ports. Extensible embedded application capabilities
enable these switches to integrate services into the network, consolidating devices and appliances
to simplify deployment and reduce power consumption as well as rack space.
Extremely versatile, the switches can be used in high-performance, high-density building
or department cores as part of a consolidated network; for data center top-of-rack server
access; or as high-performance Layer 3, 10GbE aggregation switches in campus and data
center networks.
Data sheet | HP 5820 Switch Series
Features and benefits
Quality of Service (QoS)
•Powerful QoS feature
Creates traffic classes based on access control lists (ACLs), IEEE 802.1p precedence, IP, and
DSCP or Type of Service (ToS) precedence; supports filter, redirect, mirror, or remark; supports
congestion actions such as: strict priority (SP) queuing, weighted round robin (WRR), weighted
fair queuing (WFQ), weighted random early discard (WRED), weighted deficit round robin
(WDRR), and SP+WDRR
•Integrated network services
Extends and integrates application capability into the network, with support for open
application architecture (OAA) modules ring resiliency protection protocol (RRPP)
•Provides fast recovery for ring
Ethernet-based topology; helps facilitate consistent application performance for applications
such as VoIP
Management
•Remote configuration and management
Enables configuration and management through a secure Web browser or a CLI located on a
remote device
•IEEE 802.1ab LLDP discovery
Advertises and receives management information from adjacent devices on a network,
facilitating easy mapping by network management applications
•USB support
––File copy
Allows users to copy switch files to and from a USB flash drive
•DHCP options
Provides server (RFC 2131), client, snooping, and relay options
•SNMPv1, v2c, and v3
Facilitates centralized discovery, monitoring, and secure management of networking devices
•sFlow®
Provides scalable ASIC-based network monitoring and accounting; this allows network
operators to gather a variety of sophisticated network statistics and information for capacity
planning and real-time network monitoring purposes
•Network Time Protocol (NTP)
Synchronizes timekeeping among distributed time servers and clients; keeps timekeeping
consistent among all clock-dependent devices within the network so that the devices can
provide diverse applications based on the consistent time
2
Data sheet | HP 5820 Switch Series
Connectivity
•High-density port connectivity
194 10GbE ports with a 40 Gbps resilient backplane
•Auto-MDIX
Provides automatic adjustments for straight-through or crossover cables on all 10/100 and
10/100/1000 ports
•Jumbo frames
On Gigabit Ethernet and 10 Gigabit Ethernet ports, jumbo frames allow high-performance
remote backup and disaster-recovery services
•IPv6 native support
––IPv6 host
Enables switches to be managed and deployed at the IPv6 network’s edge
––Dual stack (IPv4/IPv6)
Transitions from IPv4 to IPv6, supporting connectivity for both protocols
––MLD Snooping
Forwards IPv6 multicast traffic to the appropriate interface
––IPv6 ACL/QoS
Supports ACL and QoS for IPv6 network traffic, preventing traffic flooding
––IPv6 routing
Supports IPv6 static routes and IPv6 versions of RIP, OSPF, IS-IS, and Border Gateway
Protocol (BGP) routing protocols
Performance
•Hardware-based wire-speed access control lists (ACLs)
Helps provide high levels of security and ease of administration without impacting network
performance with a feature-rich TCAM-based ACL implementation
•Unique versatile architecture
Supports the best of both, fixed-port and modular configurations
•Cut-through switching
Delivers wire-speed, line-rate performance on all ports, as well as cut-through switching for
low latency
Resiliency and high availability
•Data center-optimized design
HP 5820AF-24XG Switch (JG219A) supports front-to-back and back-to-front airflow for hot or
cold aisles, rear rackmounts, and redundant hot-swappable AC or DC power and fans
3
Data sheet | HP 5820 Switch Series
Manageability
•Full-featured console
Provides complete control of the switch with a familiar CLI
•Web interface
Allows configuration of the switch from any Web browser on the network
•RMON and sFlow
Provides advanced monitoring and reporting capabilities for statistics, history, alarms, and
events
•Multiple configuration files
Allows multiple configuration files to be stored to a flash image
•Troubleshooting
––Ingress and egress port monitoring enable network problem solving
––Traceroute and ping enable testing of network connectivity
––Virtual cable tests provide visibility to cable problems
Layer 2 switching
•32K MAC addresses
Provides access to many Layer 2 devices
•4,094 port-based VLANs
Provides security between workgroups
•IEEE 802.1ad QinQ and selective QinQ
Increases the scalability of an Ethernet network by providing a hierarchical structure; connects
multiple LANs on a high-speed campus or metro network
•Gigabit Ethernet port aggregation
Allows grouping of ports to increase overall data throughput to a remote device
•10GbE port aggregation
Allows grouping of ports to increase overall data throughput to a remote device
•Spanning Tree/MSTP, RSTP, and STP root guard
Prevents network loops
•sFlow
Allows traffic sampling
•GVRP VLAN Registration Protocol
Allows automatic learning and dynamic assignment of VLANs
Layer 3 services
•Address resolution protocol (ARP)
Determines the MAC address of another IP host in the same subnet; supports static ARPs;
gratuitous ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP
operation between subnets or when subnets are separated by a Layer 2 network
•Dynamic host configuration protocol (DHCP)
Simplifies the management of large IP networks and supports client and server; DHCP Relay
enables DHCP operation across subnets
4
Data sheet | HP 5820 Switch Series
Layer 3 routing
•Layer 3 IPv4 routing
Provides routing of IPv4 at media speed; supports static routes, RIP and RIPv2, OSPF, IS-IS, and
BGP
•Routing Information Protocol (RIP) and RIPng support
Provides complete support of RIP for both IPv4 and IPv6
•OSPF and OSPFv3 support
Provides complete support of OSPF for both IPv4 and IPv6
•IS-IS and IS-ISv6 support
Provides complete support of IS-IS for both IPv4 and IPv6
•Layer 3 IPv6 routing
Provides routing of IPv6 at media speed; supports static routes, RIPng, OSPFv3, IS-ISv6, and
BGP4+
•Bidirectional Forwarding Detection (BFD)
Enables link connectivity monitoring and reduces network convergence time for RIP, OSPF,
BGP, IS-IS, VRRP, MPLS, and IRF
•Virtual Router Redundancy Protocol (VRRP) and VRRP Extended
Allows quick failover of router ports
•Policy-based routing
Makes routing decisions based on policies set by the network administrator
•IGMPv1, v2, and v3
Allows individual hosts to be registered on a particular VLAN
•PIM-SSM, PIM-DM, and PIM-SM (for IPv4 and IPv6)
Support IP multicast address management and inhibition of DoS attacks
•Equal-Cost Multipath (ECMP)
Enables multiple equal-cost links in a routing environment to increase link redundancy and
scale bandwidth
Security
•Defense in-depth security
Provides integrated and distributed security enforcement that can be managed from a central
location, such as the HP Intelligent Management Center (IMC)
•Advanced processor queuing mechanism
Helps prevent denial-of-service (DoS) attacks, while DHCP snooping helps enable that devices
can only receive an IP address from a legitimate DHCP server on the network
•RADIUS/HWTACACS
Eases switch management security administration by using a password authentication server
5
Data sheet | HP 5820 Switch Series
•Secure Shell (SSHv2)
Encrypts all transmitted data for secure, remote CLI access over IP networks
•IEEE 802.1X-based dynamic delivery of QoS, ACLs, and VLANs
Allows complete control over user network access
•Guest VLAN
Provides a browser-based environment to authenticated clients that is similar to IEEE 802.1X
•Port isolation
Secures and adds privacy, and prevents malicious attackers from obtaining user information
•Port security
Allows access only to specified MAC addresses, which can be learned or specified by the
administrator
•MAC-based authentication
Allows or denies access to the switch based on a client MAC address
•IP source guard
Helps prevent IP spoofing attacks
•HTTPS management
Provides secure Web management
•Unicast Reverse Path Forwarding (URPF)
Limits malicious traffic on a network
•Multi-Customer Edge (MCE)­— Multicast Virtual Routing and Forwarding (MVRF)
Provides MPLS edge router support
•Public key infrastructure (PKI)
Is used to control access
Convergence
•Voice VLAN
Automatically assigns VLAN and priority for IP phones, simplifying network configuration and
maintenance
•LLDP-MED
Is a standard extension that automatically configures network devices, including LLDP-capable
IP phones
•Internet Group Management Protocol (IGMP)
Utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4
multicast networks; supports IGMPv1, v2, and v3
•Protocol Independent Multicast (PIM)
Defines modes of Internet multicasting to allow one-to-many and many-to-many
transmission of information; supports PIM Dense Mode (DM), Sparse Mode (SM), and Source-Specific Mode (SSM)
6
Data sheet | HP 5820 Switch Series
Monitor and diagnostics
•Port mirroring
Enables traffic on a port to be simultaneously sent to a network analyzer for monitoring
•OAM (IEEE 802.3ah)
Operations, administration and maintenance (OAM) management capability detects data link
layer problems that occur in the “last mile”; monitors the status of the link between the two
devices
•CFD (IEEE 802.1ag)
Connectivity fault detection (CFD) provides a Layer 2 link OAM mechanism used for link
connectivity detection and fault locating
Additional information
•HP Intelligent Resilient Framework (IRF)
––Creates virtual resilient switching fabrics, where two or more switches perform as a single
Layer 2 switch and Layer 3 router
––Does not require switches to be co-located and allows them to be part of a disaster-recovery
system
––Allows servers or switches to be attached using standard LACP for automatic load balancing
and high availability
––Simplifies network operation by helping eliminate the complexity of Spanning Tree Protocol,
ECMP, or VRRP
•OAA modules
Supports wireless network management and high-performance security applications;
leverages network infrastructure investment
•Green IT and power
Improves energy efficiency through the use of the latest advances in silicon development;
shuts off unused ports and utilizes variable-speed fans, reducing energy costs
•High scalability with IRF
HP Intelligent Resilient Framework (IRF) technology simplifies the architecture of server
access networks; up to nine HP 5820/5820AF stackable switches can be combined to deliver
unmatched scalability of virtualized access layer switches and flatter, two-tier HP FlexFabric
networks using IRF, which reduces cost and complexity
Warranty and support
•1-year warranty
Advance hardware replacement with 10-calendar day delivery (available in most countries)
•Electronic and telephone support
Limited electronic and business-hours telephone support is available from HP for the entire
warranty period; to reach our support centers, refer to hp.com/networking/contact-support;
for details on the duration of support provided with your product purchase, refer to hp.com/
networking/warrantysummary
•Software releases
To find software for your product, refer to hp.com/networking/support; for details on the
software releases available with your product purchase, refer to hp.com/networking/
warrantysummary
7
Data sheet | HP 5820 Switch Series
HP 5820 Switch Series
Specifications
HP 5820-14XG-SFP+ Switch with 2
Interface Slots & 1 OAA Slot (JC106B)
HP 5820-24XG-SFP+ Switch (JC102B)
HP 5820AF-24XG Switch (JG219B)
I/O ports and slots
14 SFP+ 10GbE ports; Duplex: full only
2 extended module slots
1 open module slot
4 RJ-45 auto-negotiating 10/100/1000
ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T)
Supports a maximum of 14 SFP+ ports
plus 8 8/4/2 Gbps Fibre Channel SFP+
ports, with optional module
24 SFP+ 10GbE ports; Duplex: full only
4 RJ-45 auto-negotiating 10/100/1000
ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T)
Supports a maximum of 24 SFP+ ports
plus 4 autosensing 10/100/1000 ports
24 fixed 1000/10000 SFP+ ports
2 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASE-T/100BASE-TX: half or
full; 1000BASE-T: full only
Additional ports and slots
1 RJ-45 serial console port
1 RJ-45 serial console port
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
Power supplies
2 power supply slots
1 minimum power supply required
(ordered separately)
2 power supply slots
1 minimum power supply required
(ordered separately)
2 power supply slots
1 minimum power supply required
(ordered separately)
Fan tray
Includes: 1 x JC096A
1 fan tray slot
Base product includes fan tray.
Includes: 1 x JC098A
1 fan tray slot
Base product includes fan tray.
2 fan tray slots
The customer must order fan trays, as
fan trays are not included with the switch.
This system requires two same-direction
airflow fan trays to function properly. The
system should not be operated with only
one fan tray for more than 24 hours. The
system should not be operated without
a fan tray more than two minutes. The
system should not be operated outside
of the temperature range of 32°F (0°C) to
113°F (45°C). Failure to comply with these
operating requirements may void the
product warranty.
17.32(w) x 18.39(d) x 3.39(h) in. (43.99 x
46.7 x 8.61 cm) (2U height)
33.29 lb (15.1 kg)
17.32(w) x 16.81(d) x 1.73(h) in. (44.0 x
42.7 x 4.4 cm) (1U height)
18.74 lb (8.5 kg)
25.98(w) x 17.32(d) x 1.72(h) in. (65.99 x
43.99 x 4.37 cm) (1U height)
22.05 lb (10 kg) shipping weight
Physical characteristics
Dimensions
Weight
8
Data sheet | HP 5820 Switch Series
Memory and processor
Performance
Latency
Throughput
Routing/Switching capacity
Routing table size
MAC address table size
Environment
Operating temperature
Operating relative humidity
Acoustic
Electrical characteristics
Frequency
Maximum heat dissipation
AC voltage
DC voltage
Maximum power rating
Safety
HP 5820-14XG-SFP+ Switch with 2
Interface Slots & 1 OAA Slot (JC106B)
HP 5820-24XG-SFP+ Switch (JC102B)
HP 5820AF-24XG Switch (JG219B)
2048 MB SDRAM, 512 MB flash; packet
buffer size: 2 MB
2048 MB SDRAM, 512 MB flash; packet
buffer size: 2 MB
2048 MB flash, 512 MB SDRAM; packet
buffer size: 2 MB
2.02 µs (Cut Through), 2.02 µs (Store and
Forward) (64-byte packets)
up to 363 million pps (64-byte packets)
488 Gbps
12000 entries (IPv4)
32000 entries
2.02 µs (Cut Through), 2.02 µs (Store and
Forward) (64-byte packets)
up to 363 million pps (64-byte packets)
488 Gbps
12000 entries (IPv4)
32000 entries
3 µs (64-byte packets)
32°F to 113°F (0°C to 45°C)
10% to 90%, noncondensing
Low-speed fan: 44.3 dB, High-speed fan:
54.1 dB
32°F to 113°F (0°C to 45°C)
10% to 90%, noncondensing
Low-speed fan: 48.4 dB, High-speed fan:
59.7 dB
32°F to 113°F (0°C to 45°C)
10% to 90%, noncondensing
Low-speed fan: 60.1 dB, High-speed fan:
69.9 dB
50/60 Hz
836 BTU/hr (881.98 kJ/hr)
100–120 / 200–240 VAC
-48 to -60 VDC
300 W
50/60 Hz
631 BTU/hr (665.71 kJ/hr)
100–120 / 200–240 VAC
-48 to -60 VDC
300 W
50/60 Hz
607 BTU/hr (640.39 kJ/hr)
100–120 / 200–240 VAC
-48 to -60 VDC
650 W
Notes
Maximum power rating and maximum
heat dissipation are the worst-case
theoretical maximum numbers provided
for planning the infrastructure with fully
loaded PoE (if equipped), 100% traffic,
all ports plugged in, and all modules
populated.
Maximum power rating and maximum
heat dissipation are the worst-case
theoretical maximum numbers provided
for planning the infrastructure with fully
loaded PoE (if equipped), 100% traffic,
all ports plugged in, and all modules
populated.
Maximum power rating and maximum
heat dissipation are the worst-case
theoretical maximum numbers provided
for planning the infrastructure with fully
loaded PoE (if equipped), 100% traffic,
all ports plugged in, and all modules
populated.
UL 60950-1; EN 60825-1 Safety of Laser
Products-Part 1; EN 60825-2 Safety of
Laser Products-Part 2; IEC 60950-1; CAN/
CSA-C22.2 No. 60950-1; Anatel; ULAR;
GOST; EN 60950-1/A11; FDA 21 CFR
Subchapter J; NOM; ROHS Compliance
UL 60950-1; EN 60825-1 Safety of Laser
Products-Part 1; EN 60825-2 Safety
of Laser Products-Part 2; IEC 60950-1;
CAN/CSA-C22.2 No. 60950-1; Anatel;
ULAR; GOST; EN 60950-1/A11; FDA 21 CFR
Subchapter J; NOM; ROHS Compliance
UL 60950-1; EN 60825-1 Safety of Laser
Products-Part 1; EN 60825-2 Safety
of Laser Products-Part 2; IEC 60950-1;
CAN/CSA-C22.2 No. 60950-1; Anatel;
ULAR; GOST; EN 60950-1/A11; FDA 21 CFR
Subchapter J; NOM; ROHS Compliance
360 million pps
484 Gbps
12000 entries (IPv4)
32000 entries
9
Data sheet | HP 5820 Switch Series
HP 5820-14XG-SFP+ Switch with 2
Interface Slots & 1 OAA Slot (JC106B)
HP 5820-24XG-SFP+ Switch (JC102B)
HP 5820AF-24XG Switch (JG219B)
VCCI Class A; EN 55022 Class A; ICES-003
Class A; ANSI C63.4 2003; AS/NZS CISPR
22 Class A; EN 61000-3-2:2006; EN
61000-3-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47,
Part 15) Class A
VCCI Class A; EN 55022 Class A; ICES-003
Class A; ANSI C63.4 2003; AS/NZS CISPR
22 Class A; EN 61000-3-2:2006; EN
61000-3-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47,
Part 15) Class A
VCCI Class A; EN 55022 Class A; ICES-003
Class A; ANSI C63.4 2003; AS/NZS CISPR
22 Class A; EN 61000-3-2:2006; EN
61000-3-3:1995 +A1:2001+A2:2005; EMC Directive 2004/108/EC; FCC (CFR 47,
Part 15) Class A
ETSI EN 300 386 V1.3.3
EN 55024:1998+ A1:2001 + A2:2003 EN 61000-4-2; IEC 61000-4-2
EN 61000-4-3; IEC 61000-4-3
EN 61000-4-4; IEC 61000-4-4
EN 61000-4-5; IEC 61000-4-5
EN 61000-4-6; IEC 61000-4-6
IEC 61000-4-8; EN 61000-4-8
EN 61000-4-11; IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
ETSI EN 300 386 V1.3.3
EN 55024:1998+ A1:2001 + A2:2003 EN 61000-4-2; IEC 61000-4-2
EN 61000-4-3; IEC 61000-4-3
EN 61000-4-4; IEC 61000-4-4
EN 61000-4-5; IEC 61000-4-5
EN 61000-4-6; IEC 61000-4-6
IEC 61000-4-8; EN 61000-4-8
EN 61000-4-11; IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
ETSI EN 300 386 V1.3.3
EN 55024:1998+ A1:2001 + A2:2003 EN 61000-4-2; IEC 61000-4-2
EN 61000-4-3; IEC 61000-4-3
EN 61000-4-4; IEC 61000-4-4
EN 61000-4-5; IEC 61000-4-5
EN 61000-4-6; IEC 61000-4-6
IEC 61000-4-8; EN 61000-4-8
EN 61000-4-11; IEC 61000-4-11
EN 61000-3-2, IEC 61000-3-2
EN 61000-3-3, IEC 61000-3-3
Management
IMC—Intelligent Management Center;
command-line interface; Web browser;
SNMP Manager; Telnet; HTTPS; RMON1;
FTP
IMC—Intelligent Management Center;
command-line interface; Web browser;
SNMP Manager; Telnet; HTTPS; RMON1;
FTP
IMC—Intelligent Management Center;
command-line interface; Web browser;
SNMP Manager; Telnet; HTTPS; RMON1;
FTP
Notes
The customer must order a power supply,
as the device does not come with a PSU. At least one JC087A or JC090A is required.
The customer must order a power supply,
as the device does not come with a PSU.
At least one JC087A or JC090A is required.
The customer must order power supply,
as the device does not come with a PSU.
At least one JC680A or JC681A is required.
Services
Refer to the HP website at hp.com/
networking/services for details on the
service-level descriptions and product
numbers. For details about services
and response times in your area, please
contact your local HP sales office.
Refer to the HP website at hp.com/
networking/services for details on the
service-level descriptions and product
numbers. For details about services
and response times in your area, please
contact your local HP sales office.
Refer to the HP website at hp.com/
networking/services for details on the
service-level descriptions and product
numbers. For details about services
and response times in your area, please
contact your local HP sales office.
Emissions
Immunity
Generic
EN
ESD
Radiated
EFT/Burst
Surge
Conducted
Power frequency magnetic field
Voltage dips and interruptions
Harmonics
Flicker
10
Data sheet | HP 5820 Switch Series
Standards and Protocols
(applies to all products in series)
General protocols
IEEE 802.1ag Service Layer OAM
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s (MSTP)
IEEE 802.1v VLAN classification by
Protocol and Port
IEEE 802.1w Rapid Reconfiguration of
Spanning Tree
IEEE 802.3ad Link Aggregation Control
Protocol (LACP)
IEEE 802.3ae 10 Gigabit Ethernet
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 925 Multi-LAN Address Resolution
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1542 BOOTP Extensions
RFC 2131 DHCP
RFC 2453 RIPv2
RFC 3046 DHCP Relay Agent
Information Option
RFC 3576 Ext to RADIUS (CoA only)
RFC 3768 VRRP
RFC 4675 RADIUS VLAN & Priority
RFC 3323—A Privacy Mechanism for the
Session Initiation Protocol (SIP)
802.1r—GARP Proprietary Attribute
Registration Protocol (GPRP)
IP multicast
RFC 2934 Protocol Independent Multicast
MIB for IPv4
RFC 3376 IGMPv3 (host joins only)
RFC 3618 Multicast Source Discovery
Protocol (MSDP)
RFC 3973 Draft 2 PIM Dense Mode
RFC 4601 Draft 10 PIM Sparse Mode
IPv6
RFC 2080 RIPng for IPv6
RFC 2460 IPv6 Specification
RFC 2710 Multicast Listener Discovery
(MLD) for IPv6
RFC 2740 OSPFv3 for IPv6
RFC 2925 Remote Operations MIB (ping
only)
RFC 3019 MLDv1 MIB
RFC 3162 RADIUS and IPv6
RFC 3315 DHCPv6 (client and relay)
RFC 3315 DHCPv6 (client only)
RFC 3810 MLDv2 (host joins only)
RFC 4022 MIB for TCP
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4293 MIB for IP
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
MIBs
IEEE8021-PAE-MIB
IEEE8023-LAG-MIB
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1657 BGP-4 MIB
RFC 1724 RIPv2 MIB
RFC 1850 OSPFv2 MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2013 SNMPv2 MIB for UDP
RFC 2233 Interface MIB
RFC 2273 SNMP-Notification-MIB
RFC 2452 IPv6-TCP-MIB
RFC 2454 IPv6-UDP-MIB
RFC 2465 IPv6 MIB
RFC 2466 ICMPv6 MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
RFC 2573 SNMP-Notification MIB
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2688 MAU-MIB
RFC 2787 VRRP MIB
RFC 2819 RMON MIB
RFC 2925 Ping MIB
RFC 3414 SNMP-User based-SM MIB
RFC 3415 SNMP-View based-ACM MIB
RFC 3418 MIB for SNMPv3
RFC 3621 Power Ethernet MIB
RFC 3826 AES for SNMP’s USM MIB
RFC 4133 Entity MIB (version 3) LLDP-EXT-DOT1-MIB
LLDP-EXT-DOT3-MIB
LLDP-MIB
Network management
IEEE 802.1ab Link Layer Discovery
Protocol (LLDP)
RFC 2819 Four groups of RMON: 1
(statistics), 2 (history), 3 (alarm), and
9 (events)
RFC 3176 sFlow
ANSI/TIA-1057 LLDP Media Endpoint
Discovery (LLDP-MED)
SNMPv1/v2c/v3
OSPF
RFC 2328 OSPFv2
RFC 3101 OSPF NSSA
Security
IEEE 802.1X Port-based Network Access
Control
RFC 1492 TACACS+
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
11
Data sheet | HP 5820 Switch Series
HP 5820 Switch Series accessories
(applies to all products in series)
Transceivers
HP X125 1G SFP LC LH40 1310nm Transceiver (JD061A)
HP X120 1G SFP LC LH40 1550nm Transceiver (JD062A)
HP X125 1G SFP LC LH70 Transceiver (JD063B)
HP X120 1G SFP RJ45 T Transceiver (JD089B)
HP X120 1G SFP LC SX Transceiver (JD118B)
HP X120 1G SFP LC LX Transceiver (JD119B)
HP X130 10G SFP+ LC SR Transceiver (JD092B)
HP X130 10G SFP+ LC LRM Transceiver (JD093B)
HP X130 10G SFP+ LC LR Transceiver (JD094B)
HP X130 10G SFP+ LC ER 40km Transceiver (JG234A)
HP X130 10G SFP+ LC LH 80km Transceiver (JG915A)
HP X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable (JD095C)
HP X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable (JD096C)
HP X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable (JD097C)
HP X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable (JG081C)
HP X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable (JG329A)
HP X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable (JG330A)
HP X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable (JG331A)
Cables
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable (QK732A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable (QK733A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable (QK734A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable (QK735A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable (QK736A)
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable (QK737A)
Power supply
HP RPS1600 Redundant Power System (JG136A)
HP RPS1600 1600W AC Power Supply (JG137A)
HP 5820 Switch model-specific accessories
HP 5820-14XG-SFP+ Switch with 2 Interface Slots & 1
OAA Slot (JC106B)
HP 5800 4-port 10GbE SFP+ Module (JC091A)
HP 5800 2-port 10GbE SFP+ Module (JC092B)
HP 5800 300W AC Power Supply (JC087A)
HP 5800 300W DC Power Supply (JC090A)
HP 5800 2RU Spare Fan Assembly (JC096A)
HP 5820 VPN Firewall Module (JD255A)
HP 5820-24XG-SFP+ Switch (JC102B)
HP 5800 300W AC Power Supply (JC087A)
HP 5800 300W DC Power Supply (JC090A)
HP 5800 1RU Spare Fan Assembly (JC098A)
HP 5820AF-24XG Switch (JG219B)
HP 58x0AF 650W AC Power Supply (JC680A)
HP 58x0AF 650W DC Power Supply (JC681A)
HP 58x0AF Back (power side) to Front (port side) Airflow Fan Tray (JC682A)
HP 58x0AF Front (port side) to Back (power side) Airflow Fan Tray (JC683A)
Learn more at
hp.com/networking
Sign up for updates
hp.com/go/getupdated
Share with colleagues
Rate this document
© Copyright 2010–2012, 2014–2015 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
sFlow is a registered trademark of InMon Corp.
4AA3-0739ENW, March 2015, Rev. 7