Vollrath LidSaver2 In-Counter Operator's Manual

Operator’s Manual
LidSaver™ 2 In-Counter Lid Dispensers
Item No.
Description
LS02I
Dispenses lids 3-¹⁄₄" - 4" (8.2 - 10.1 cm)
LS02P
Dispenses lids 4-¹⁄₁₆" - 4-³⁄₄" (10.3 - 12 cm)
NOTICE: Each LidSaver™ 2 is factory set to dispense a particular lid
style. If you change lid manufacturers or sizes, your
LidSaver™ 2 will need to modified. Vollrath offers lid
change out kits that are easy to install. Visit
www.Vollrath.com for more information
OVERVIEW
G
Thank you for purchasing this Vollrath equipment. Before operating the
equipment, read and familiarize yourself with the following operating
and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. Save the original box and packaging. Use this packaging
to ship the equipment if repairs are needed.
H
E
C
F
D
I
B
SAFETY PRECAUTIONS
J
K
L
To ensure safe operation, read the following statements and understand
their meaning. This manual contains safety precautions which are
explained below. Please read carefully.
A
WARNING
Warning is used to indicate the presence of a hazard that will or can
cause severe personal injury or death.
CAUTION
Caution is used to indicate the presence of a hazard that will or can
cause minor or major personal injury if the caution is ignored.
NOTICE: Notice is used to note information that is important but not
hazard-related.
A
Door Open Button. Keeps the door open for easy loading.
B
Bezel/Housing
C
“A” Claw. Marked with lid manufacturer and model no.
D
Door Spring
E
Spring Pin
F
Overfill Protection Bracket
G
Pivoting Pager Flipper. For smooth lid loading.
H
Piston Lid Plate
I
Nylon Door Sheer Screws. (10-24 x ³⁄₈ R.H.M.S.)
J
Door
K
“B” Claw. Marked with lid manufacturer and model no.
L
Nylon Lid Claw Pivot Sheer Screws. (6-32 x ³⁄₄ F.H.M.S.)
Please register your product at Vollrath.com
©
2016 The Vollrath Company L.L.C.
Part No. 8012602-1 en
5/31/16
IN-COUNTER INSTALLATION
Tools Needed
•
•
•
•
•
•
4. Remove the bezel/housing.
#2 Phillips Screwdriver
Drill
0.125" – 0.136" Drill Bit (For #8 Pilot Hole)
Sabre Saw or Hand Router
Cabinet Cut-Out Template (provided)
(4) #8 x 1.00" Flat Head Wood Screws (included)
1. Use the supplied cabinet cut-out template to cut the LidSaver™ 2
tube hole and drill four mounting screw pilot holes.
/6L
:22'6&5(:
3,/27
;
/6L
/63+286,1*
/6L+286,1*
&87287
/6L
/63
5. Mount the LidSaver™ 2 into your cabinet using the four #8 flat head
wood screws.
/6L
/63
/63
$%29(
&2817(5
/63
/63
/6L
$%29(
&2817(5
2. Remove the bezel/housing by opening the door and pushing the
sides of the housing to clear the snaps.
PUSH
PUSH
6. Replace the bevel/housing.
3. Pull the bezel/housing forward and tilt it downward allowing it to flex
around the edge of the open door.
2
LidSaver™ 2 In-Counter Lid Dispensers Operator’s Manual
LOADING
CLEANING
1. Before loading lids, verify your lids match the manufacturer and lid
number noted on the lid plate label.
Regularly clean the inside and outside of your LidSaver™.
1. Remove all lids from LidSaver™.
2. Remove the bezel/housing (refer to installation instructions).
3. Wipe the interior and exterior with a cotton cloth and warm soapy
water.
4. Saturate each pager assembly with warm soapy water several times.
Flex the flipper portion of the pager to verify flippers operate freely.
5. Push the piston to the back of the tube to expose the bottom of tube.
Wipe the bottom of the tube.
MAINTENANCE
2. Pull the door open past 90 degrees. Push the button on the side of the
housing. This will enable the door to stay open for easy loading.
Tune-Up Your LidSaver™
When lids do not dispense correctly your LidSaver™ may need to be
adjusted. Order a tune-up kit. See www.Vollrath.com for ordering
information.
3. Separate the lids prior to loading to release any lids that may have been
pressed together during packaging.
4. Load lids or cups.
• Lids must be loaded with the front of the lid stack facing forward.
NOTICE: DO NOT overstock lids. Compressing lids may result in
dispensing problems.
5. If dispensing tabbed lids, align all lid tabs either up (12:00) or
down (6:00) to avoid interference with the lid claws.
NOTICE: Each LidSaver™ is factory set to dispense a particular lid. If
you change manufacturers or sizes, your LidSaver™ 2 will
need to be modified. Vollrath offers lid change out kits that
are easy to install. Visit www.Vollrath.com for more
information.
6. Gently pull door open past 90 degrees and then release the door. It will
automatically close.
LidSaver™ 2 In-Counter Lid Dispensers Operator’s Manual
3
TROUBLESHOOTING
Problem
More than one lid releases when
opening door
Might be Caused By
Course of Action
Your lid may be incorrect for your
LidSaver™ 2 settings.
Read label on “lid plate”. If this does not match your lids, order a lid
change kit” to reset your LidSaver™ 2 for your lid.
LidSaver™ 2 may be overfilled with lids.
When lids are compressed too tightly Remove lids and flake the stack. Avoid overstocking lids when
from overstocking they will not dispense loading.
well. Instruct staff to not overstock lids.
Pager flipper not returning to proper
Using warm soapy water, thoroughly saturate pager and flipper
working position after loading lid stack. until flipper operates freely.
Pager not securely fastened down.
Inconsistent dispensing
Grasp each pager to determine if it is loose and allows movement
within the adjustment slot. Order a tune-up kit to set these
components accurately.
Due to manufacturing defects, damaged
lids or poorly stacking lid types, some
lids may not dispense as planned. Under
these rare conditions your customer is
still able to easily retrieve a lid.
SERVICE AND REPAIR
Serviceable parts are available on Vollrath.com.
To avoid serious injury or damage, never attempt to repair the unit or replace a damaged power cord yourself. Do not send units directly to
The Vollrath Company LLC. Please contact Vollrath Technical Services for instructions.
When contacting Vollrath Technical Services, please be ready with the item number, model number (if applicable), serial number, and proof of
purchase showing the date the unit was purchased.
WARRANTY STATEMENT FOR THE VOLLRATH CO. L.L.C.
This warranty does not apply to products purchased for personal, family or household use, and The Vollrath Company LLC does not offer a written
warranty to purchasers for such uses.
The Vollrath Company LLC warrants the products it manufactures or distributes against defects in materials and workmanship as specifically
described in our full warranty statement. In all cases, the warranty runs from the date of the end user’s original purchase date found on the receipt.
Any damages from improper use, abuse, modification or damage resulting from improper packaging during return shipment for warranty repair will
not be covered under warranty.
For complete warranty information, product registration and new product announcement, visit www.vollrath.com.
www.vollrath.com
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A.
Main Tel: 800.624.2051 or 920.457.4851
Main Fax: 800.752.5620 or 920.459.6573
Customer Service: 800.628.0830
Canada Customer Service: 800.695.8560
©
Technical Services
[email protected]
Induction Products: 800.825.6036
Countertop Warming Products: 800.354.1970
All Other Products: 800.628.0832
2016 The Vollrath Company L.L.C.
Part No. 8012602-1 en
5/31/16