Icop PMX-090T-5A User manual

DM&P Vortex86MX+

Panel PC with 9

” TFT LCD

 Model:

PMX-090T-5A / PMX-090T-8A

PMX-090T-5A-512 / PMX-090T-8A-512

(Revision 1.0A)

i

Revision

Date

2012/11/20

Version Description

Version 1.0 Initial Release i

Copyright

The information in this manual is subject to change without notice for continuous improvement in the product. All rights are reserved. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this document. And makes no commitment to update or to keep current the information contained in this manual.

No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part, in any form or by any means without the prior written permission of the ICOP Technology Inc.



Copyright 2012 ICOP Technology Inc.

Manual No. IUMPMX090-01 Ver.1.0A Nov, 2012

Trademarks Acknowledgment

Vortex86MX



is the registered trademark of DMP Electronics Inc. Other brand names or product names appearing in this document are the properties and registered trademarks of their respective owners. All names mentioned herewith are served for identification purpose only.

Safety Information

 Read these Safety instructions carefully.

 Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.

 Do not expose your Panel PC to rain or moisture, in order to prevent shock and fire hazard.

 Keep PMX-090T away from humidity.

 Do not open the cabinet to avoid electrical shock. Refer to your nearest dealer for qualified personnel servicing.

 Never touch un-insulated terminals or wire unless your power adaptor is disconnected.

 Locate your Panel PC as close as possible to the socket outline for easy access and to avoid force caused by entangling of your arms with surrounding cables from the Panel PC.

 USB connectors are not supplied with Limited Power Sources.

 If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage.

D

O NOT ATTEMPT TO OPEN OR TO DISASSEMBLE THE CHASSIS

(E

NCASING

)

OF THIS

PRODUCT

.

P

LEASE CONTACT YOUR DEALER FOR SERVICING FROM QUALIFIED TECHNICIAN

.

ii

PMX-090T DM&P Vortex86MX+ Panel PC with 9” WSVGA TFT LCD

1

Table of Contents

General Information .............................................................................. 3

1.1

1.2

1.3

1.4

1.5

Product Description ...................................................... 1

Product Specification ................................................... 2

Inspection standard for TFT-LCD Panel ........................ 4

Product Dimension ....................................................... 7

Ordering Information ................................................... 8

1.6 Packing List ................................................................... 8

2 System Installation ................................................................................ 9

2.1 CPU Board Outline ........................................................ 9

2.2

2.3

2.4

2.5

2.6

Connector Summary................................................... 10

Connector Pin Assignments ........................................ 11

External I/O Overview ................................................ 13

External I/O Pin Assignment ....................................... 14

System Mapping ......................................................... 16

2.7 Watchdog Timer ......................................................... 20

3 Driver Installation ................................................................................ 21

3.1 PMX-090T Development Note ................................... 22

3.2 BIOS Default setting ................................................... 24

Warranty ......................................................................................................... 25 iii


1 .General Information

1.1 Product Description

PMX-090T is an ultra-compact platform for the present demanding embedded and productive applications. It has new Vortex86MX+ SoC CPU which consumes only minimum power requirement when running at 1GHz, and DDR2 memory provides faster data transfer rate. By using 9” TFT LCD, PMX-090T becomes the perfect choice for a limited budget. In additional, the integrated

10/100M Ethernet port supplies the communication capability which makes

PMX-090T can be more widely used when running with Linux, Windows CE, and

Windows XP environment to become the perfect solution for system integration.

1


1.2 Product Specification

Table 1-1 Product Specification

CPU Board Specifications

CPU

Cache

BIOS

Memory

Watchdog Timer

LAN

Audio

Internal Drives

I/O

DM&P Vortex86MX+ 1GHz

L1:16KB I-Cache, 16KB D-Cache

L2: 256KB Cache

AMI BIOS

512MB/1GB DDR2 onboard

Software programmable from

30.5u to 512 seconds x 2 sets

Integrated 10/100M Ethernet

HD Audio-Realtek ALC262 CODEC

Compact Flash Type I / II slot

Micro SD slot

1GB or 2GB Flash Memory onboard (Optional)

RS-232/422/485 x 1

USB ports (Ver2.0) x 2

RJ-45 Port x 1

Mechanical & Environment

Power Requirement

Single Voltage +5VDC ( 5A )

Multi Voltage +8~+35VDC ( 8A )

1.5A@5VDC Power Consumption

Operating

Temperature

Storage

Temperature

0 ~ +50℃ ( 32 ~ +122℉)

-10 ~ +60℃ ( 14 ~ +140℉)

2


Operating Humidity

Dimensions

Weight

Front Panel

Protection

Certification

LCD Specifications

Display Type

Backlight Unit

Display Resolution

Brightness (cd/m

2

)

Contrast Ratio

Display Color

Pixel Pitch (mm)

Viewing Angle

Backlight Lifetime

Touchscreen

Type

Resolution

Transmittance

Controller

Software Driver

Durability

0% ~ 90% relative humidity, non-condensing

236.6 x 146 x 35mm (9.31 x 5.75 x 1.38 inches)

468g

IP 65

CE / FCC / VCCI / Vibration

9” TFT LCD

LED

1024(W) x 600(H)

300 nits

500 : 1

262, 144

190.5 (H) x 189 (V)

Vertical 120 o

,

Horizontal 140 o

25,000 hrs

Analog Resistive

Continuous

80%

PS / 2 interface

DOS / Linux / WinCE / WinXP

1 million

3


1.3 Inspection standard for TFT-LCD Panel

Table 1-2 Inspection Standard

DEFECT TYPE LIMIT Note

VISUAL

DEFECT

ELECTRICAL

DEFECT

INTER

NAL

SPOT

FIBER

POLARIZER

BUBBLE

φ＜0.15mm

0.15mm≦φ≦0.5mm

0.5mm＜φ

0.03mm<W≦0.1mm, L≦

5mm

1.0mm＜W, 1.5mm＜L

φ＜0.15mm

0.15mm≦φ≦0.5mm

0.5mm＜φ

Ignore

N≦4

N=0

N≦3

N=0

Ignore

N≦2

N=0

Mura It’ OK if mura is slight visible through 6%ND filter

BRIGHT DOT

DARK DOT

TOTAL DOT

TWO ADJACENT DOT

C

Area

N≦0

A Grade

O

Area

Total

N≦2 N≦2

N≦2

N≦0

N≦3 N≦3

N≦4

N≦1 pair

N≦1 pair

THREE OR MORE

ADJACENT DOT

LINE DEFECT

NOT ALLOWED

NOT ALLOWED

B Grade

C

Area

O

Area

N≦2 N≦3

Total

N≦5

N≦3 N≦5

N≦5 N≦6

N≦1 pair

N≦1 pair

N≦8

N≦8

N≦1 pair

Note1

Note1

Note1

Note3

Note2

Note2

Note4

(1) One pixel consists of 3 sub-pixels, including R, G, and B dot.

(Sub-pixel = Dot)

(2) LITTLE BRIGHT DOT ACCEPTITABLE UNDER 6 % ND-Filter

(3) If require G0 grand (Total dot N≦0), please contact region sales.

4


[Note 1] W : Width[mm], L : Length[mm], N : Number, φ: Average Diameter.

1. White / Black Spot

2. Polarizer Bubble

Fig 1-1

Fig 1-2

[Note 2] Bright dot is defined through 6% transmission ND Filter as following.

Fig 1-3

5


[Note 3]

C Area: Center of display area

O Area: Outer of display area

[Note 4]

Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D status) adjacent defect dots, including bright and dart adjacent dot. And they will be counted 2 defect dots in total quantity.

A

C

R G R G R G R G R G R G

R Defect Dot


R

Adjacent Dot


B D

(1) The defects that are not defined above and considered to be problem shall be reviewed and discussed by both parties.

Defects on the Black Matrix, out of Display area, are not considered as a defect or counted.

6


1.4 Product Dimension

Fig 1-4 Product Dimension

7


1.5 Ordering Information

Table 1-3 Ordering Information

PART NUMBER

PMX-090T-5A 9” Panel PC w/1GB

DESCRIPTION

DDR2 / 2USB / Line-Out / LAN / COM / CF / MicroSD /

PMX-090T-8A

PMX-090T-5A-512

PMX-090T-8A-512

Power Adapter

9” Panel PC w/1GB


8-35 DC Support

9” Panel PC w/512MB


Power Adapter

9” Panel PC w/512MB


8-35 DC Support

1.6 Packing List

Table 1-4 Packing List

PART NUMBER PACKAGE

PMX-090T-5A

PMX-090T-8A

PMX-090T-5A

PMX-090T-8A

Power-20W-3PIN

PMX-090T-5A-512 PMX-090T-5A-512 Power-20W-3PIN

PMX-090T-8A-512 PMX-090T-8A-512

WLAN KIT

(Optional)

USB-WLAN-IPEX-KIT WIRELESS- WIRELESS-

ANTENNA-157 CABLE-150MM

8


2 .System Installation

2.1 CPU Board Outline

Fig 2-1 PMX CPU Board

9


2.2 Connector Summary

Table 2-1 Summary Table

Nbr

J1

J3

J4

J5

J8

J9

J10

J14

J18

Description

CF Master/Slave Switch

USB

USB

USB (Optional)

PS/2 Keyboard

Type of Connections

Slide Switch

External USB Connector

External USB Connector

2.0mm 5-pin wafer

2.54mm 5-pin box header

Pin nbrs.

ON/OFF

6-pin

6-pin

5-pin

5-pin

PS/2Keyboard External Mini DIN Socket 6-pin

COM2(RS232/422/485) External D-Sub Male Connector 9-pin

VGA

Micro SD Card Socket

2.0mm 10-pin box header

Micro SD socket

10-pin

J23

J24

J25

J26

Audio Line-Out

Audio Mic-In

COM3 (TX, RX)

COM4 (TX, RX

J30 SOM CPU Board Socket

J31 4-Wires Touch connector

J32

RJ45

USB (Wi-Fi Optional)

Ethernet

PWR

PWR

CF1

Power Connector (5A)


CF Card Socket

1.25mm Phone Jack

2.0mm 4-pin wafer

1.25mm 3-pin wafer

1.25mm 3-pin wafer

SOM CPU Board Socket

1.25mm 4-pin wafer

Internal USB Connector

External RJ45 Connector

External Mini DIN Socket

External Power Plug

CF Type I/II Socket

4-pin

3-pin

3-pin

200-pin

4-pin

6-pin

8-pin

3-pin

2-pin

10


2.3 Connector Pin Assignments

J8: PS/2 Keyboard

J1: CF Master/Slave Switch

Pin # Signal Name Pin # Signal Name

Pin #

On

OFF

Signal Name

Master

Slave

1

3

5

KBCLK

NC

VCC

2

4

KBDAT

GND

J3: USB


1 VCC 2

3 USBD2+ 4

5 GND 6

USBD2-

GND

GND

J9: PS/2 Keyboard


5

7

9

1

3

KBCLK

GND

MSDATA

GND

GND

2 MSCLK

4 KBDATA

6

8

VCC

GND

J4: USB


1 VCC 2 USBD3-

3 USBD3+ 4

5 GND 6

GND

GND

J5: USB (Optional)

Pin #

1

2

3

4

5

Signal Name

VCC

USBD1-

USBD1+

GND

GND

J10: COM1 RS232/422/485

(Change setting by BIOS)


1

3

5

7

9

DCD1/

422TX- /

RS485-

TXD1 /

422RX+

GND

RTS1

RI1

2

4

6

8

RXD1 /

422TX+ /

RS485+

DTR1 /

422RX-

DSR1

CTS1

11


J14: VGA


1

3

R OUT

G OUT

2

4

5 B OUT 6

7 HSYNC 8

9 VSYNCD 10

GND

GND

GND

GND

GND

J24: MIC-IN

Pin #

1

2

3

4

Signal Name

MICVREF

GND

GND

MIC-IN

J25: COM3 (TX, RX)

Pin #

1

2

3

Signal Name

GND

TXD3

RXD3

J26: COM4 (TX, RX)

Pin #

1

2

3

Signal Name

GND

TXD4

RXD4

J31: 4-Wires Touch connector

Pin #

1

2

3

4

Signal Name

Y-

X-

Y+

X+

J32: USB (WiFi Optional)


1 VCC 2 USBD2-

3 USBD2+ 4

5 GND 6

GND

GND

PWR: Power Connector (5A)

Pin #

1

2

3

4

Signal Name

+5V

GND

NC

GND

PWR: Power Connector (8A)

Pin #

1

2

Signal Name

+ 8 ~ 35V

GND

12


2.4 External I/O Overview

{ PMX-090T-8A / PMX-090T-8A-512 }

Fig 2-2 PMX-090T-8A I/O overview

{ PMX-090T-5A / PMX-090T-5A-512 }

Fig 2-3 PMX-090T-5A I/O overview

{Note}

1. Wireless is optional


2.5 External I/O Pin Assignment

Power Switch

USB Port

Pin #

|

O

Status

ON

OFF


Pin # Signal Name

1 +5V

2 GND

3 NC



1 +8 ~ 35V

2 GND

Audio Line-Out


1 GND

2 LOUTL

3 Open Touch

4 Open Touch

5 VREFOUT


1 VCC

2

3

USB0-

USB0+

4

5

GND

GGND

6 GGND

PS/2 Keyboard


3

4

1

2

5

6

KBCLK

PMCLK

GND

KBDAT

PMDAT

SB5V

14


J10: COM1 RS232/422/485 (Change setting by BIOS)


5

7

1 DCD1/422TX-/RS485- 2 RXD1/422TX+/RS485+

3 TXD1 / 422RX+ 4 DTR1 / 422RX-

9

GND

RTS1

RI1

6

8

DSR1

CTS1

RJ45

Pin #

1

3

5

7

Signal Name

FTXD+

FRXIN+

NC

NC

Pin #

2

4

6

8

Signal Name

FTXD-

NC

FRXIN-

NC

15


2.6 System Mapping

Table 2-2 Technical Data Sheet

Technical Data Sheet

Product Name PMX-090T-8A DM171C Doc.No. QMT1000014R00

Product

Description

9” Vortex86MX Panel PC with 1GB

Doc. Category Confidential

DDR2 / 2USB / Line-out

/ LAN / 1COM / CF / MicroSD

Issued Date 10-08-2012

System Mapping

Memory Mapping

Address Description

00000000-0009FFFF

000A0000-000AFFFF

Usage

*

*

000B0000-000B7FFF

000B8000-000BFFFF

000C0000-000C7FFF

000C8000-000CFFFF

000CC000-000CFFFF

000D0000-000D7FFF

000D8000-000DBFFF

000DC000-000DFFFF

System RAM

EGA/VGA Video Memory

MDA RAM, Hercules Graphics

Display RAM

CGA Display RAM

EGA/VGA BIOS ROM

Boot ROM Enable

Console Redirection Enable

Expansion ROM Space

SPI FLASH Emulation Floppy A

Enable

Expansion ROM Space

*

*

*

000E0000-000EFFFF

000F0000-000FFFFF

*

FEBD9000-FEBD90FF

FEBDA000-FEBDA0FF

FEBDB400-FEBDB4FF

USB Legacy SCSI ROM Space

Motherboard BIOS

Standard OpenHCD USB Host

Controller

Standard OpenHCD USB Host

Controller

On board Ethernet Adapter

*

*

*

16


FEBDB800-FEBDB8FF

FEBDBC00-FEBDBCFF

I/O Mapping

I/O Address

0000h - 000Fh

0010h - 0017h

0020h - 0021h

0022h - 0023h

002Eh - 002Fh

0040h - 0043h

0048h - 004Bh

004Eh - 004Fh

0060h

0061h

0062h - 0063h

0064h

0065h

0066h

0067h

0068h - 006Dh

0070h - 0071h

0072h - 0075h

0078h - 007Ch

0080h - 008Fh

0092h

Standard Enhanced PCI to USB

Host Controller

Standard Enhanced PCI to USB

Host Controller

Owner

DMA 8237-1

COM 9

PIC 8259-1

Indirect Access Registers

( 6117D configuration port )

Forward to LPC BUS

Timer counter 8254

PWM counter 8254

Forward to LPC BUS

Keyboard / Mouse Data Port

Port B + NMI Control Port

8051 download 4K Address Counter

Keyboard / Mouse Status /

Command Port

WatchDog0 Reload Counter

8051 Download 8bit Data Port

WatchDog1 Reload Counter

WatchDog1 Control Register

CMOS RAM Port

MTBF Control Register

GPIO Port 0,1,2,3,4 Default Setup

DMA Page Register

System Control Register

*

*

Usage

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

17


0098h - 009Ch

00A0h - 00A1h

00C0h - 00DFh

00E0h - 00EFh

0170h - 0177h

01F0h - 01F7h

0220h - 0227h

0228h - 022Fh

0238h - 023Fh

0278h - 027Fh

02E8h - 02EFh

02F8h - 02FFh

0338h - 033Fh

0376h

03E8h - 03EFh

03F0h - 03F7h

03F6h

03F8h - 03FFh

0480h - 048Fh

0490h - 0499h

04D0h - 04D1h

0CF8h - 0CFFh

DE00h - DEFFh

FC00h - FC05h

FC08h - FC0Dh

GPIO Direction Control

PIC 8259-2

DMA 8237-2

DOS 4G Page Access

IDE1 (IRQ 15)

IDE0 (IRQ 14)

COM8 Forward to LPC BUS



Printer Port (IRQ 7, DMA 0)

COM4 (IRQ 11)

COM2 (IRQ 3)


IDE1 ATAPI Device Control Write only Register

COM3 (IRQ 10)

Floppy Disk (IRQ 6, DMA 2)

IDE0 ATAPI Device Control Write only Register

COM1 (IRQ 4)

DMA High Page Register

Instruction Counter Register

8259 Edge,/ Level Control Register

PCI configuration port

On Board LAN

SPI Flash BIOS Control Register

(internal SPI Flash Base address)

External SPI BUS Control Register

( Output Pin Configurable

GPIO3[0-3] )

18


*

*

*

*

*

*

*

*

*

*

*

*

*

*

*

IRQ Mapping

IRQ#

IRQ0

IRQ9

IRQ10

IRQ11

IRQ12

IRQ13

IRQ14

IRQ15

IRQ1

IRQ2

IRQ3

IRQ4

IRQ5

IRQ6

IRQ7

IRQ8

DMA Mapping

DMA#

DMA0

DMA1

DMA2

DMA3

DMA5

DMA6

DMA7

Description

System Timer

Keyboard Controller

Cascade for IRQ8 - 15

USB

Serial Port 1

USB

Unassigned

Ethernet 10/100M LAN

Real Time Clock

USB

USB

Audio

Mouse

Math Coprocessor

Hard Disk Controller#1

Hard Disk Controller#2

Description

Floppy Disk Controller

19


Usage

Usage

*

*

*

*

*

*

*

*

*

*

*

*

*

*

2.7 Watchdog Timer

There are two watchdog timers in PMX-090T, we also provide DOS, Linux and

WinCE example for your reference. For more technical support, please visit: http://tech.icop.com.tw or download the PDF file: dmp.com.tw/tech

20


3 .Driver Installation

VGA

The Vortex86MX processor is integrated RDC Display chip which is an ultra low powered graphics chipset with total power consumption at around 1-1.5 W.

LAN

The Vortex86MX+ processor is integrated 10/100Mbps Ethernet controller that supports both 10/100BASE-T and allows direct connection to your

10/100Mbps Ethernet based Local Area Network for full interaction with local servers, wide area networks such as the Internet.

I/O and IRQ settings can be done by software with the supplied utility software, or it can be set for Plug and Play compatibility. The controller supports:

Half / Full-Duplex Ethernet function to double channel bandwidth, auto media detection.

AUDIO

The ALC262 series are 4-Channel High Definition Audio Codecs with UAA

(Universal Audio Architecture) featuring two 24-bit stereo DACs and three 20-bit stereo ADCs, they are designed for high performance multimedia desktop and laptop systems. The ALC262 series incorporates proprietary converter technology to achieve over 100dB Signal-to-Noise ratio playback quality; easily meeting

PC2001 requirements and also bringing PC sound quality closer to consumer electronic devices.

21


Operating system support

The PMX-090T provides the VGA and LAN drivers for Linux, Windows CE,

Windows XP Professional, and Windows Embedded standard (XPE).

(Linux can use with Compact Flash card only.)

Please get the drivers from ICOP official website: tech.icop.com.tw

PMX-090T also supports most of the popular Linux distributions, for more detail information, please visit DMP official website:dmp.com.tw/tech/vortex86mx

3.1 PMX-090T Development Note

<Primary /Secondary IDE: Master or Slave>

1. Micro SD: Primary Master

2. CF Slot: Secondary IDE: Master or Slave (User can use slide switch (in side of

CF slot) to adjust Master or Slave

<Window CE6.0 development guide>

Windows Embedded CE 6.0 BSP, trial CE image and development notes, please visit technical website to get more information: tech.icop.com.tw

<Linux installation note>

Please forced the IDE setting in BIOS to PIO mode before install Linux on PMX-090

T as follows:

3. Go to the advanced BIOS setting and make the “Onboard IDE Operate

Mode” is “Legacy Mode”

22


4. Go to the PCI/PnP and make the “PCI IDE BusMaster” is “Disable"

< XP professional /Home /Embedded and Windows 2000 installation note >

Please visit technical website to get more information: tech.icop.com.tw

<Enhance CF to run the UDMA2/4>

Please select ICOP “ICF Card” to supporting UDMA 2/4 Mode.

<How to boot up from the Micro SD card>

1. Get into the BIOS setup Utility

2. Go to the Advanced

3. Choose Primary IDE Pin Select: SD card

4. Press “F10” to save configuration changes and exit setup

23


3.2 BIOS Default setting

If the system cannot be booted after BIOS changes are made, Please follow below procedures in order to restore the CMOS as default setting.

Press < End > Key, when the power on

Press < Del > to enter the AMI BIOS setup

Press < F9 > to Load Optimized defaults

Press < F10 > to Save configuration changes and exit setup

24


Warranty

This product is warranted to be in good working order for a period of one year from the date of purchase. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms. This warranty does not apply to products damaged by misuse, modifications, accident or disaster.

Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, originality to use this product. Vendor will not be liable for any claim made by any other related party. Return authorization must be obtained from the vendor before returned merchandise will be accepted. Authorization can be obtained by calling or faxing the vendor and requesting a Return Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear problem description.

All Trademarks appearing in this manuscript are registered trademark of their respective owners.

All Specifications are subject to change without notice.

© ICOP Technology Inc. 2012

25


No results