HP ProBook 640 G1 Notebook PC
HP ProBook 645 G1 Notebook PC
HP ProBook 650 G1 Notebook PC
HP ProBook 655 G1 Notebook PC
Maintenance and Service Guide
IMPORTANT! This document is intended for HP
authorized service providers only.
© Copyright 2015 Hewlett-Packard
Development Company, L.P.
Bluetooth is a trademark owned by its
proprietor and used by Hewlett-Packard
Company under license. Intel and Core are U.S.
registered trademarks of Intel Corporation.
AMD is a trademark of Advanced Micro Devices,
Inc. Microsoft and Windows are U.S. registered
trademarks of the Microsoft group of
companies. SD Logo is a trademark of
its proprietor.
The information contained herein is subject to
change without notice. The only warranties for
HP products and services are set forth in the
express warranty statements accompanying
such products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable for
technical or editorial errors or omissions
contained herein.
Second Edition: April 2015
First Edition: November 2013
Document Part number: 728342-002
Product notice
This guide describes features that are common
to most models. Some features may not be
available on your computer.
Not all features are available in all editions of
Windows 8. This computer may require
upgraded and/or separately purchased
hardware, drivers, and/or software to take full
advantage of Windows 8 functionality. See
http://www.microsoft.com for details.
Software terms
By installing, copying, downloading, or
otherwise using any software product
preinstalled on this computer, you agree to be
bound by the terms of the HP End User License
Agreement (EULA). If you do not accept these
license terms, your sole remedy is to return the
entire unused product (hardware and
software) within 14 days for a refund subject
to the refund policy of your place of purchase.
For any further information or to request a full
refund of the computer, please contact your
local point of sale (the seller).
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place
the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat
surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as
pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact the skin or a soft
surface, such as pillows or rugs or clothing, during operation. The computer and the AC adapter comply with
the user-accessible surface temperature limits defined by the International Standard for Safety of
Information Technology Equipment (IEC 60950).
iii
iv
Safety warning notice
Table of contents
1 Product description ....................................................................................................................................... 1
2 External component identification ................................................................................................................. 8
Display ................................................................................................................................................................... 8
Buttons and fingerprint reader (select models only) ......................................................................................... 10
Keys ...................................................................................................................................................................... 11
Lights ................................................................................................................................................................... 13
TouchPad ............................................................................................................................................................. 15
Front ..................................................................................................................................................................... 15
Left side ............................................................................................................................................................... 16
Right side ............................................................................................................................................................. 18
Rear (select models only) .................................................................................................................................... 19
Bottom ................................................................................................................................................................. 20
3 Illustrated parts catalog .............................................................................................................................. 22
Service tag ........................................................................................................................................................... 22
Computer major components ............................................................................................................................. 24
Display assembly subcomponents ..................................................................................................................... 38
Cables ................................................................................................................................................................... 39
Plastics Kit ........................................................................................................................................................... 40
Mass storage devices .......................................................................................................................................... 41
Miscellaneous parts ............................................................................................................................................. 42
Sequential part number listing ........................................................................................................................... 43
4 Removal and replacement procedures preliminary requirements .................................................................... 58
Tools required ...................................................................................................................................................... 58
Service considerations ........................................................................................................................................ 58
Plastic parts ....................................................................................................................................... 58
Cables and connectors ...................................................................................................................... 59
Drive handling ................................................................................................................................... 59
Grounding guidelines ........................................................................................................................................... 59
Electrostatic discharge damage ....................................................................................................... 59
Packaging and transporting guidelines ......................................................................... 61
Workstation guidelines ................................................................................ 61
v
5 Removal and replacement procedures for Customer Self-Repair parts ............................................................. 63
Component replacement procedures ................................................................................................................. 63
Battery ............................................................................................................................................... 64
Service cover ..................................................................................................................................... 65
Hard drive .......................................................................................................................................... 66
Modem module (select models only) ............................................................................................... 68
Primary memory module .................................................................................................................. 69
Expansion memory module .............................................................................................................. 72
WWAN module (select models only) ................................................................................................. 74
WLAN module .................................................................................................................................... 75
Optical drive ...................................................................................................................................... 77
Solid-state drive ................................................................................................................................ 79
Keyboard ........................................................................................................................................... 80
6 Removal and replacement procedures for Authorized Service Provider parts ................................................... 87
Fan and heat sink assembly ................................................................................................................................ 87
Base enclosure ..................................................................................................................................................... 91
USB board ............................................................................................................................................................ 94
Power button board ............................................................................................................................................. 96
Fingerprint reader board ..................................................................................................................................... 98
Smart card reader .............................................................................................................................................. 100
System board ..................................................................................................................................................... 101
Speakers ............................................................................................................................................................ 105
Function button board ....................................................................................................................................... 107
Processor ........................................................................................................................................................... 109
TouchPad ........................................................................................................................................................... 111
Power connector cable ...................................................................................................................................... 113
RTC battery ........................................................................................................................................................ 114
Display assembly ............................................................................................................................................... 116
7 Computer Setup ......................................................................................................................................... 121
Windows 8 — Computer Setup (BIOS), MultiBoot, and System Diagnostics ................................................... 121
Using Computer Setup .................................................................................................................... 121
Starting Computer Setup .............................................................................................. 121
Navigating and selecting in Computer Setup ............................................................... 121
Restoring default settings in Computer Setup ............................................................ 122
Updating the BIOS ......................................................................................................... 122
Determining the BIOS version .................................................................... 122
Downloading a BIOS update ....................................................................... 123
Using MultiBoot ............................................................................................................................... 124
vi
About the boot device order ......................................................................................... 124
Choosing MultiBoot preferences .................................................................................. 124
Setting a new boot order in Computer Setup ............................................ 124
Dynamically choosing a boot device using the f9 prompt ........................ 125
Setting a MultiBoot Express prompt .......................................................... 125
Entering MultiBoot Express preferences ................................................... 125
Using HP PC Hardware Diagnostics (UEFI) (select models only) .................................................... 125
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device ............................................... 126
Windows 7 — Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) .......................... 126
Using Computer Setup .................................................................................................................... 126
Starting Computer Setup .............................................................................................. 126
Navigating and selecting in Computer Setup ............................................................... 126
Restoring factory settings in Computer Setup ............................................................ 127
Updating the BIOS ......................................................................................................... 128
Determining the BIOS version .................................................................... 128
Downloading a BIOS update ....................................................................... 128
Using MultiBoot ............................................................................................................................... 129
About the boot device order ......................................................................................... 129
Choosing MultiBoot preferences .................................................................................. 129
Setting a new boot order in Computer Setup ............................................ 129
Dynamically choosing a boot device using the f9 prompt ........................ 130
Setting a MultiBoot Express prompt .......................................................... 130
Entering MultiBoot Express preferences ................................................... 130
Using HP PC Hardware Diagnostics (UEFI) (select models only) .................................................... 132
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device ............................. 132
8 Specifications ........................................................................................................................................... 133
Computer specifications .................................................................................................................................... 133
Hard drive specifications ................................................................................................................................... 133
Hard drive specifications (continued) ............................................................................................................... 134
9 Backup and recovery .................................................................................................................................. 136
Windows 8 ......................................................................................................................................................... 136
Backing up your information .......................................................................................................... 136
Performing a system recovery ....................................................................................................... 136
Using the Windows recovery tools ............................................................................... 136
Using f11 recovery tools .............................................................................................. 137
Using Windows operating system media (purchased separately) .............................. 138
Using Windows Refresh or Windows Reset .................................................................. 139
Using HP Software Setup .............................................................................................. 139
Windows 7 ......................................................................................................................................................... 140
vii
Creating recovery media and backups ........................................................................................... 140
Guidelines ..................................................................................................................... 140
Creating recovery media with HP Recovery Disc Creator (select models only) .......... 140
Creating recovery media ............................................................................ 141
Backing up your information ........................................................................................ 141
Performing a system recovery ....................................................................................................... 142
Using the Windows recovery tools ............................................................................... 143
Using f11 recovery tools (select models only) ............................................................ 143
Using Windows 7 operating system media .................................................................. 144
SUSE Linux – Backup and recovery ................................................................................................................... 145
Creating backups ............................................................................................................................. 145
Backing up your information .......................................................................................................... 145
Performing a system recovery ....................................................................................................... 146
Remove everything and reinstall SLED .......................................................................................... 146
10 Statement of Volatility ............................................................................................................................ 148
Non-volatile memory usage ............................................................................................................................. 149
Questions and answers ..................................................................................................................................... 151
11 Power cord set requirements .................................................................................................................... 152
Requirements for all countries ......................................................................................................................... 152
Requirements for specific countries and regions ............................................................................................. 152
12 Recycling ................................................................................................................................................ 154
Index ........................................................................................................................................................... 155
viii
1
Product description
Category
Description
Product Name
HP ProBook 640 G1 Notebook PC
HP ProBook 645 G1 Notebook PC
HP ProBook 650 G1 Notebook PC
HP ProBook 655 G1 Notebook PC
Processors
Chipset
●
Intel® Dual Core i7-4600M 2.90-GHz processor (up to 3.6-GHz), 4.0-MB, (1600-MHz FSB,
4.0-MB L3 cache, 37W)
●
Intel Dual Core i5-4330M 2.80-GHz processor (1600-MHz FSB, 3.0-MB L3 cache, 37 W)
●
Intel Dual Core i5-4300M 2.60-GHz processor (1600-MHz FSB, 3.0-MB L3 cache, 37 W)
●
Intel Dual Core i5-4200M 2.50-GHz processor (1600-MHz FSB, 3.0-MB L3 cache, 37 W)
●
Intel Dual Core i3-4100M 2.50-GHz processor (1600-MHz FSB, 3.0-MB L3 cache, 37 W)
●
Intel Dual Core i3-4000M 2.40-GHz processor (1600-MHz FSB, 3.0-MB L3 cache, 37 W)
●
AMD® Quad Core A10-5750M with Radeon HD 8650G Graphics (3.5 GHz/2.5 GHz; 4.0-MB
L2 cache, 35W)
●
AMD Quad Core A10-4600M with Radeon HD 7660G Graphics (3.2 GHz/2.3 GHz; 4.0-MB
L2 cache, 35W)
●
AMD Quad Core A8-5550M with Radeon HD 8550G Graphics (3.1 GHz/2.1 GHz; 4.0-MB L2
cache, 35W)
●
AMD Quad Core A8-4500M with Radeon HD 7640G Graphics (2.8 GHz/1.9 GHz; 4.0-MB L2
cache, 35W)
●
AMD Quad Core A6-5350M with Radeon HD 8450G Graphics (3.5 GHz/2.9 GHz; 4.0-MB L2
cache, 35W)
●
AMD Quad Core A6-4400M with Radeon HD 7520G Graphics (3.2 GHz/2.7 GHz; 4.0-MB L2
cache, 35W)
●
AMD Quad Core A4-5150M with Radeon HD 8350G Graphics (3.3 GHz/2.7 GHz; 4.0-MB L2
cache, 35W)
●
AMD Quad Core A4-4300M with Radeon HD 7420G Graphics (3.0 GHz/2.5 GHz; 4.0-MB L2
cache, 35W)
Mobile IntelQM87
Mobile Intel HM87
Fusion Controller Hub
AMD A76M Fusion Controller Hub (FCH)
Graphics
Switchable graphics:
●
Intel HD Graphics 4600 with shared video memory
●
AMD Radeon HD 8750M
Support for hybrid (switchable) graphics
Frame buffer width 128-bit
Support dual-display ports through the dock
1
Category
Description
Support for up to 4 total displays with discrete configurations (through Advanced Docking
Station)
Support AMD Eyefinity Technology (with AMD Discrete graphics)
Panel
●
14.0-in full high-definition (FHD) AG UWA, SVA (1920x1080 resolution, 300 nits, 72%
CG, 1.3-mm + PSR slim design eDP panel) with camera and WWAN
●
14.0-in full high-definition (FHD) AG UWA, SVA (1920x1080 resolution, 300 nits, 72%
CG, 1.3-mm + PSR slim design eDP panel) with WWAN
●
14.0-in full high-definition (FHD) AG UWA, SVA (1920x1080 resolution, 300 nits, 72%
CG, 1.3-mm + PSR slim design eDP panel) with WWAN
●
14.0-in full high-definition (FHD) AG UWA, SVA (1920x1080 resolution, 300 nits, 72%
CG, 1.3-mm + PSR slim design eDP panel)
●
14.0-in HD AG SVA (1600x1900 resolution, 250 nits, 45% CG, 1.2-mm flat design eDP
panel) with camera and WWAN
●
14.0-in HD AG SVA (1600x1900 resolution, 250 nits, 45% CG, 1.2-mm flat design eDP
panel) with WWAN
●
14.0-in HD AG SVA (1600x1900 resolution, 250 nits, 45% CG, 1.2-mm flat design eDP
panel) with camera
●
14.0-in HD AG SVA (1600x1900 resolution, 250 nits, 45% CG, 1.2-mm flat design eDP
panel)
●
14.0-in HD AG SVA (1366x768 resolution, 200 nits, 45% CG, 1.2-mm flat design eDP
panel) with camera and WWAN
●
14.0-in HD AG SVA (1366x768 resolution, 200 nits, 45% CG, 1.2-mm flat design eDP
panel) with WWAN
●
14.0-in HD AG SVA (1366x768 resolution, 200 nits, 45% CG, 1.2-mm flat design eDP
panel) with camera
●
14.0-in HD AG SVA (1366x768 resolution, 200 nits, 45% CG, 1.2-mm flat design eDP
panel)
●
15.6-in, full high-definition (FHD), AntiGlare (AG) SVA (1920x1080 resolution, 300 nits,
60% CG, 1.2-mm slim design eDP panel) with camera and WWAN
●
15.6-in FHD AG SVA (1920x1080 resolution, 300 nits, 60% CG, 1.2-mm slim design eDP
panel) with WWAN
●
15.6-in FHD AG SVA (1920x1080 resolution, 300 nits, 60% CG, 1.2-mm slim design eDP
panel) with camera
●
15.6-in FHD AG SVA (1920x1080 resolution, 300 nits, 60% CG, 1.2-mm slim design eDP
panel)
●
15.6-in (1366x768 resolution) 200 nits, 45% CG, 1.2-mm flat design eDP panel) with
camera and WWAN
●
15.6-in (1366x768 resolution) 200 nits, 45% CG, 1.2-mm flat design eDP panel) with
WWAN
●
15.6-in (1366x768 resolution) 200 nits, 45% CG, 1.2-mm flat design eDP panel) with
camera
●
15.6-in HD AG SVA (1366x768 resolution) 200 nits, 45% CG, 1.2-mm flat design eDP
panel)
All panels are 16:9 aspect ratio
Memory
Two customer-accessible/upgradable memory module slots
Support for DDR3L 1600-MHz PC3-12800 dual channel memory
2
Chapter 1 Product description
Category
Description
Support for 16384-MB of system RAM in the following configurations:
Flash cache
●
16384-MB total system memory (8192-MB×2 or 4096-MB×4)
●
12288-MB Total system semory (8192-MB + 4096-MB)
●
8192-MB total system memory (8192-MB or 4096-MB×2)
●
8192-MB total system memory (8192-MB×1)
●
6144-MB Total system memory (4096-MB + 2048-MB)
●
4096-MB total system memory (4096-MB×1)
●
2048-MB total system memory (2048-MB×1)
32-GB MLC SATA-3 module (Intel Smart Response Technology (SRT)
Dedicated MiniCard slot
Support for no flash cache option
Fast Flash Standby not supported
Not available on computer models equipped with WWAN capability, a solid-state drive (SSD),
or a self-encrypted drive (SED)
Not available on computer models equipped with the Linux operating system
MiniCard solid-state drive
256-GB SATA-3 SSD
180-GB SATA-3 SSD
128-GB mSATA SSD
SSD is set as primary storage if selected; hard drive becomes secondary storage
Hard drive
Support for 6.35-cm (2.5-in) hard drives in 7.0-mm (.28-in) and 9.5-mm (.37-in) thickness
Support for Serial ATA
Support for 3D DriveGuard hard drive protection
Support toolless removal
Support for the following hard drives:
●
1-TB, 5400-rpm, 9.5-mm
●
750-GB, 7200-rpm, 7.0-mm
●
500-GB, 7200-rpm, 7.0-mm
●
500-GB, 5400-rpm, 7.0-mm, FIPS (not available on computer models equipped with the
Windows 8, Windows 7, or Windows 8 downgrade operating systems)
●
500-GB, 7200-rpm, 7.0-mm, self-encrypting drive (not available on computer models
equipped with the Windows 8, Windows 7, or Windows 8 downgrade operating systems)
●
320-GB, 7200-rpm, 7.0-mm
Support for the following 6.35-cm (2.5-in) solid-state drives:
Upgrade drive
●
256-GB SATA-3 self-encrypting SSD (not available on computer models equipped with
the Windows 8, Windows 7, or Windows 8 downgrade operating systems)
●
180-GB SATA-3 SSD
●
128-GB SATA-3 SSD
Support for the following 9.5-mm (.37-in) , SATA optical drives:
3
Category
Description
●
Blu-ray ROM DVD±RW SuperMulti Double-Layer Drive
●
DVD±RW SuperMulti Double-Layer Drive
●
DVD-ROM Drive
Support for 6.35-cm (2.5-in) 750-GB, 7200-rpm SATA hard drive in 7.0-mm (.28-in) and 9.5mm (.37-in) thicknesses
Support for the following 6.35-cm (2.5-in) SATA III solid-state drives:
●
512-GB SSD
●
256-GB SED SSD (not available on computer models equipped with the Windows 8,
Windows 7, or Windows 8 downgrade operating systems)
Supports for no Upgrade drive option (bezel)
Audio and video
Stereo speakers
Dual array microphone (select models only)
HD Audio with DTS Studio sound
DTS sound+
Integrated HD 720p webcam (fixed [no tilt], activity LED, 1280×720 by 30 frames per second)
Support for no webcam option
Ethernet
Intel I218-LM 10/100/1000 Ethernet, with Intel I218-LM Gigabit Network Connection (select
models only)
Realtek RTL8151GH-CG 10/100/1000 Ethernet (select models only)
Support for Power Optimizer
Intel Stable Image Platform Program (SIPP)
Wireless
Integrated wireless local area network (WLAN) options by way of wireless module
Two WLAN antennas built into display assembly
Support for the following WLAN formats:
●
Intel 802.11 a/b/g/n 2x2 + BT 4.0 Combo Adapter
●
Intel 802.11 2x2 AC + BT 4.0 Combo Adapter
●
Intel 802.11 2x2 a/b/g/n + BT 4.0 Combo Adapter
●
Intel 802.11 2x2 a/b/g/n
●
Broadcom 802.11 a/b/g/n 2x2 + BT 4.0 LE PCIe+USB HMC WW Combo Adapter
●
Atheros 802.11 b/g/n 1x1 + BT 4.0 Combo Adapter
●
Atheros 802.11 b/g/n 1x1
Integrated wireless wide area network (WWAN) options by way of wireless module (select
models only)
Two WWAN antennas built into display assembly
Security provided by subscriber identify module (SIM), slot located in battery bay
Support for the following WWAN formats:
4
Chapter 1 Product description
●
HP lt4111 LTE/EV-DO/HSPA+ Mobile Broadband Module
●
HP lt4112 LTE/HSPA+ Mobile Broadband Module
Category
Description
●
HP hs3110 HSPA+ Mobile Broadband Module
External media cards
Digital Media Reader Slot with push-push technology. Reads data from and writes data to
digital memory cards such as Secure Digital (SD).
Ports
●
AC adapter, HP Smart
●
Audio-in (mono microphone)/audio-out (stereo headphone) combo jack
●
Battery (secondary)
●
DisplayPort 1.2
●
Docking
●
RJ-45 (Ethernet)
●
USB 3.0 (3 or 4)
●
USB 3.0 charging (1)
●
VGA (Dsub 15 pin) supporting: 1920×1200 external resolution @ 75 Hz, hot plug and
unplug and autodetection for correct output to wide-aspect vs. standard aspect video
Keyboard/pointing devices
Full-size, spill-resistant keyboard with drain and numeric keypad
Gesture support: MultiTouch gestures enabled, two-finger scrolling, and pinchzoom as default
Support for Windows 8 dual-point (pointing stick with 3 pointing stick buttons plus TouchPad
with 3 TouchPad buttons)
DuraKeys
Spill Resistant with drain
TouchPad requirements:
Power requirements
Power requirements (continued)
Security
●
On/off button
●
Support for 2-way scroll
●
Taps enabled by default
●
Gestures enabled by default:
◦
2-finger scrolling
◦
2-finger zoom (pinch)
Support for the following AC adapters:
●
90-W, HP Smart Adapter
●
65-W, HP Smart Adapter
Support for the following batteries
●
9-cell cylindrical 100-WHr, 3.0-Ah, Li-ion battery
●
6-cell cylindrical 55-WHr, 2.8-Ah, Li-ion battery
●
6-cell cylindrical 55-WHr, 2.55-Ah, Li-ion battery
●
3-cell cylindrical 33-WHr, 2.0-Ah, Li-ion battery
Support security lock
Trusted platform module (TPM) 1.2 (Infineon; soldered down) and TPM Enhanced Drive Lock
(For the People's Republic of China and Asia Pacific countries and regions, disabled
but available)
5
Category
Description
Fingerprint reader (select models only)
Integrated smart card reader
Operating system
Preinstalled:
●
Windows 8.1 Professional 64-bit
●
Windows 8.1 Professional 64-bit (MSNA)
●
Win 8.1 Professional 64-bit DPK with Windows 7 Professional 64-bit Image
●
Win 8.1 Professional 64-bit DPK with Windows 7 Professional 32-bit Image
●
Windows 8.1 Chinese Market 64-bit
●
Windows 8.1 Emerging Market 64-bit
●
Windows 8.1 Multi-Language 64-bit
●
Windows 8 Professional 64-bit
●
Windows 8 Multi-Language 64-bit
●
Windows 8 Emerging Market 64-bit
●
Windows 8 CH 64-bit (available only in the People's Republic of China with Hardware
Kit)
●
Windows 8 Professional 64-bit DPK with Windows 7 Professional 64-bit Image (not
supported in the People's Republic of China)
●
Windows 7 Professional 64-bit
●
Windows 7 Professional 64-bit MSNA
●
Windows 7 Professional 32-bit
●
Windows 7 Professional 32-bit MSNA
●
Windows 7 Home Premium 64-bit
●
Windows 7 Home Premium 32-bit
●
Windows 7 Basic 32-bit
●
FreeDOS 2.0
●
SuSE Linux Enterprise (SLED 11) Service Pack 2, 64-bit (not available on computer
models equipped with WWAN capability or Blu-ray ROM DVD±RW SuperMulti DoubleLayer Drive
Restore media-DRDVD:
Operating system (continued)
6
Chapter 1 Product description
●
DRDVD Windows 8.1 (available with any Windows 8 localization, required for any
Windows 8.1 Professional downgrade operating system)
●
DRDVD Windows 8 (available with any Windows 8 localization, required for any
Windows 8 Professional downgrade operating system)
●
DRDVD Windows 7 (available with any Windows 8 or Windows 7 Professional
downgrade loc)
●
SRDVD SuSE Linux Enterprise (SLED) Service Pack 2, 64-bit (available with FreeDOS and
SuSE Linux)
Restore media-OSDVD:
●
Windows 8.1 64-bit (available only and required with Windows 8 Downgrade OS except
ASIA and the People's Republic of China)
●
Windows 8 64-bit (for service only)
Category
Description
●
Windows 8 Country-Specific 64-bit (for service only)
●
Windows 8 Emerging Market 64-bit (for service only)
●
Windows 8 Professional 64-bit (available only and required with Windows 8 downgrade
operating systems)
●
Windows 7 Professional 64 -bit (available with any Windows 8 Professional or Windows
7 Professional downgrade loc, not available in the People's Republic of China)
Certified:
●
Microsoft WHQL
●
SuSE Linux Enterprise (SLED) Service Pack 2, 64-bit
Web-only support:
Serviceability
●
Windows 8.1 Professional 64-bit
●
Windows 8.1 Enterprise 64-bit
●
Windows 8.1 Multi-Language 64-bit
●
Windows 8.1 Emerging Market 64-bit
●
Windows 8.1 Chinese Market 64-bit
●
Windows 8 Enterprise 64-bit
●
Windows 7 Ultimate 64-bit
●
Windows 7 Ultimate 32-bit
●
Windows 7 Enterprise 64-bit
●
Windows 7 Enterprise 32-bit
●
Windows 7 Professional 32-bit
●
Windows 7 Basic 64-bit
●
Windows 7 Basic 32-bit
End user replaceable parts:
●
AC adapter
●
Battery (system)
●
Hard drive
●
Keyboard
●
Memory modules (2, one primary and one expansion)
●
Optical drive
●
SSD
●
WLAN module
●
WWAN module
7
2
External component identification
Display
NOTE: Your computer may look slightly different from the illustration in this section.
Component
Description
(1)
WLAN antennas (2)*
Send and receive wireless signals to communicate with wireless local
area networks (WLAN).
(2)
WWAN antennas (2)* (select models only)
Send and receive wireless signals to communicate with wireless wide
area networks (WWAN).
(3)
Internal microphones (2)
Record sound.
(4)
Webcam light
On: The webcam is in use.
(5)
Webcam
Records video and captures still photographs.
For information on using the webcam, access HP Support Assistant.
To access HP Support Assistant on the Start screen, select the HP
Support Assistant app.
(6)
8
Internal display switch
Chapter 2 External component identification
Turns off the display or initiates Sleep if the display is closed while
the power is on.
Component
Description
NOTE: The display switch is not visible on the outside of the
computer.
*The antennas are not visible on the outside of the computer. For optimal transmission, keep the areas immediately around the
antennas free from obstructions. To see wireless regulatory notices, see the section of the Regulatory, Safety, and Environmental
Notices that applies to your country or region. To access the user guides, select the HP Support Assistant app on the Start screen,
select My computer, and then select User guides.
Display
9
Buttons and fingerprint reader (select models only)
NOTE: Your computer may look slightly different from the illustration in this section.
Component
(1)
Description
Power button
●
When the computer is off, press the button to turn on the
computer.
●
When the computer is on, press the button briefly to initiate
Sleep.
●
When the computer is in the Sleep state, press the button
briefly to exit Sleep.
●
When the computer is in Hibernation, press the button
briefly to exit Hibernation.
CAUTION: Pressing and holding down the power button will
result in the loss of unsaved information.
To learn more about your power settings, see your power
options. From the Start screen, type power, select Settings, and
then select Power Options.
10
(2)
Speakers (2)
Produce sound.
(3)
Wireless button
Turns the wireless feature on or off but does not establish a
wireless connection.
(4)
Volume mute button
Mutes and restores speaker sound.
(5)
Fingerprint reader (select models only)
Allows a fingerprint logon to Windows, instead of a password
logon.
Chapter 2 External component identification
Keys
NOTE: Refer to the illustration that most closely matches your computer.
Component
Description
(1)
esc key
Displays system information when pressed in combination with
the fn key.
(2)
fn key
Executes frequently used system functions when pressed in
combination with a function key, the num lk key, the esc key, or
the b key.
(3)
Windows button
Returns you to the Start screen from an open app or the
Windows desktop.
NOTE: Pressing the Windows button again will return you to
the previous screen.
(4)
Function keys
Execute frequently used system functions when pressed in
combination with the fn key.
(5)
Windows applications key
Displays options for a selected object.
(6)
Embedded numeric keypad
When the keypad is turned on, it can be used like an external
numeric keypad.
Each key on the keypad performs the function indicated by the
icon in the upper-right corner of the key.
(7)
num lk key
Turns the embedded numeric keypad on and off when pressed
in combination with the fn key.
Keys
11
Component
Description
(1)
esc key
Displays system information when pressed in combination with
the fn key.
(2)
fn key
Executes frequently used system functions when pressed in
combination with a function key, the num lk key, the esc key, or
the b key.
(3)
Windows button
Returns you to the Start screen from an open app or the Windows
desktop.
NOTE: Pressing the Windows button again will return you to
the previous screen.
12
(4)
Function keys
Execute frequently used system functions when pressed in
combination with the fn key.
(5)
num lk key
Alternates between the navigational and numeric functions on
the integrated numeric keypad.
(6)
Integrated numeric keypad
When num lk has been enabled, it can be used like an external
numeric keypad.
Chapter 2 External component identification
Lights
NOTE: Refer to the illustration that most closely matches your computer.
Component
(1)
Description
Power light
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off.
(2)
Caps lock light
On: Caps lock is on.
(3)
TouchPad light
●
Amber: The TouchPad is off.
●
Off: The TouchPad is on.
●
Amber: Microphone sound is off.
●
Off: Microphone sound is on.
(4)
Microphone mute light
(5)
Num lock light
On: Num lock is on.
(6)
Wireless light
●
White: An integrated wireless device, such as a wireless
local area network (WLAN) device and/or a Bluetooth®
device, is on.
●
Amber: All wireless devices are off.
●
Amber: Computer sound is off.
●
White: Computer sound is on.
(7)
Mute light
Lights
13
Component
(1)
(2)
Power light
Microphone mute light
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off.
●
Amber: Microphone sound is off.
●
Off: Microphone sound is on.
(3)
Num lock light
On: Num lock is on.
(4)
Wireless light
●
White: An integrated wireless device, such as a wireless
local area network (WLAN) device and/or a Bluetooth®
device, is on.
●
Amber: All wireless devices are off.
●
Amber: Computer sound is off.
●
White: Computer sound is on.
(5)
14
Description
Mute light
(6)
Caps lock light
On: Caps lock is on.
(7)
TouchPad light
●
Amber: The TouchPad is off.
●
Off: The TouchPad is on.
Chapter 2 External component identification
TouchPad
Editorial note with empty para elements in source file
Component
Description
(1)
Pointing stick (select models only)
Moves the pointer and selects or activates items on the screen.
(2)
Left pointing stick button (select models only)
Functions like the left button on an external mouse.
(3)
TouchPad on/off button
Turns the TouchPad on and off.
(4)
Left TouchPad button
Functions like the left button on an external mouse.
(5)
Right pointing stick button (select models only)
Functions like the right button on an external mouse.
(6)
TouchPad zone
Moves the pointer and selects or activates items on the screen.
(7)
Right TouchPad button
Functions like the right button on an external mouse.
Front
TouchPad
15
Component
(1)
(2)
(3)
(4)
Description
Wireless light
Power light
AC adapter/Battery light
Hard drive light
●
White: An integrated wireless device, such as a
wireless local area network (WLAN) device and/or a
Bluetooth® device, is on.
●
Amber: All wireless devices are off.
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off.
●
White: The computer is connected to external power
and the battery is charged from 90 to 99 percent.
●
Amber: The computer is connected to external power
and the battery is charged from 0 to 90 percent.
●
Blinking amber: A battery that is the only available
power source has reached a low battery level. When
the battery reaches a critical battery level, the
battery light begins blinking rapidly.
●
Off: The battery is fully charged.
●
Blinking white: The hard drive is being accessed.
●
Amber: HP 3D DriveGuard has temporarily parked the
hard drive.
Left side
NOTE: Refer to the illustration that most closely matches your computer.
Component
(1)
Power connector
Connects an AC adapter.
(2)
RJ-45 (network) jack/lights (2)
Connects a network cable.
(3)
16
Description
USB 3.0 charging port
Chapter 2 External component identification
●
Amber (left): The network is showing activity.
●
Green (right): The network is connected.
Connects optional USB 3.0 devices and provides enhanced USB
power performance. The USB charging port can also charge
Component
Description
select models of cell phones and MP3players, even when the
computer is off
(4)
Memory card reader
Reads data from and writes data to memory cards such as
Secure Digital (SD).
(5)
USB 3.0 port
Connects optional USB 3.0 devices and provide enhanced USB
power performance.
(6)
Upgrade bay (optical drive shown)
The upgrade bay can hold either a hard drive or an optical drive
that reads and writes (select models only) to an optical disc. It
can also hold a weight saver option.
(7)
Optical drive eject button (select models only)
Releases the optical drive disc tray.
(8)
ExpressCard slot or smart card reader
(depending on the configuration)
Supports optional ExpressCards or smart cards.
Component
Description
(1)
Power connector
Connects an AC adapter.
(2)
RJ-45 (network) jack/lights (2)
Connects a network cable.
●
Amber (left): The network is showing activity.
●
Green (right): The network is connected.
(3)
USB 3.0 charging port
Connects optional USB 3.0 devices and provides enhanced USB
power performance. The USB charging port can also charge
select models of cell phones and MP3players, even when the
computer is off.
(4)
Memory card reader
Reads data from and writes data to memory cards such as
Secure Digital (SD).
(5)
USB 3.0 ports (2)
Connect optional USB 3.0 devices and provide enhanced USB
power performance.
(6)
Upgrade bay (optical drive shown)
The upgrade bay can hold either a hard drive or an optical drive
that reads and writes (select models only) to an optical disc. It
can also hold a weight saver option.
(7)
Optical drive eject button (select models only)
Releases the optical drive disc tray.
(8)
ExpressCard slot or smart card reader
(depending on the configuration)
Supports optional ExpressCards or smart cards.
Left side
17
Right side
NOTE: Your computer may look slightly different from the illustration in this section.
Component
(1)
Description
Audio-out (headphone) jack/Audio-in
(microphone) jack
Produces sound when connected to optional powered stereo
speakers, headphones, earbuds, a headset, or television audio.
Also connects an optional headset microphone.
WARNING! To reduce the risk of personal injury, adjust the
volume before putting on headphones, earbuds, or a headset.
For additional safety information, see the Regulatory, Safety,
and Environmental Notices. To access the user guides, select
the HP Support Assistant app on the Start screen, select My
computer, and then select User guides.
NOTE: When a device is connected to the jack, the computer
speakers are disabled.
NOTE: Be sure that the device cable has a 4-conductor
connector that supports both audio-out (headphone) and
audio-in (microphone).
(2)
USB 3.0 ports (2)
Connect optional USB 3.0 devices and provide enhanced USB
power performance.
(3)
Dual-Mode DisplayPort
Connects an optional digital display device, such as a highperformance monitor or projector.
(4)
External monitor port
Connects an external VGA monitor or projector.
(5)
Vents (2)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal for
the internal fan to cycle on and off during routine operation.
(6)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a deterrent, but
it may not prevent the computer from being mishandled or
stolen.
18
Chapter 2 External component identification
Rear (select models only)
Component
Description
(1)
RJ-11 (modem) jack (select models only)
Connects a modem cable.
(2)
Serial port
Connects an optional device such as a serial modem,
mouse, or printer.
Rear (select models only)
19
Bottom
Component
(1)
Description
Service cover
Provides access to the hard drive bay, the wireless LAN
(WLAN) module slot, the WWAN module slot, and the
memory module slots.
CAUTION: To prevent an unresponsive system, replace
the wireless module only with a wireless module
authorized for use in the computer by the governmental
agency that regulates wireless devices in your country or
region. If you replace the module and then receive a
warning message, remove the module to restore
computer functionality, and then contact support through
HP Support Assistant. To access HP Support Assistant on
the Start screen, select the HP Support Assistant app.
20
(2)
Battery release latch
Releases the battery.
(3)
SIM slot
Supports a wireless subscriber identity module (SIM)
(select models only). The SIM slot is located inside the
battery bay.
(4)
Docking connector
Connects an optional docking device.
(5)
Service cover release lock
Locks the service cover.
Chapter 2 External component identification
Component
Description
(6)
Service cover release latch
Releases the service cover on the computer.
(7)
Battery bay
Holds the battery.
(8)
Vents (4)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
Bottom
21
3
Illustrated parts catalog
Service tag
When ordering parts or requesting information, provide the computer serial number and model number
provided on the service tag.
22
Item
Description
Function
(1)
Product name
This is the product name affixed to the front of
the computer.
(2)
Serial number
This is an alphanumeric identifier that is unique to each
product.
(3)
Part number/Product number
This number provides specific information about
the product's hardware components. The part number
helps a service technician to determine what
components and parts are needed.
Chapter 3 Illustrated parts catalog
Item
Description
Function
(4)
Warranty period
This number describes the duration of the warranty
period for the computer.
(5)
Model description
This is the alphanumeric identifier used to locate
documents, drivers, and support for the computer.
Service tag
23
Computer major components
24
Chapter 3 Illustrated parts catalog
Item
Component
(1)
Display panel:
Spare part number
15.6-in, FHD, WLED UWVA
739998-001
15.6-in, HD, WLED UWVA
739997-001
14-in, HD WLED
747751-001
14-in, HD+ WLED
747752-001
14-in, FHD, WLED UWVA
747753-001
Raw Panel Support Kit (includes LCD back cover and wireless antennas and transceivers):
For use in models equipped with a 15.6–inch display assembly
738691-001
For use in models equipped with a 14–inch display assembly
738680–001
(2)
Top hinge cover for 15.6-in models
(3)
Keyboard (includes keyboard cable):
Keyboard for 15.6-in models with pointing stick (includes keyboard cable and pointing stick cable):
For use in Belgium
738697-A41
For use in Brazil
738697-201
For use in Bulgaria
738697-261
For use in Canada
738697-DB1
For use in the Czech Republic and Slovakia
738697-FL1
For use in Denmark
738697-081
For use in France
738697-051
For use in Germany
738697-041
For use in Greece
738697-151
For use in Hungary
738697-211
For use in Iceland
738697-DD1
For use in India
738697-D61
For use in Israel
738697-BB1
For use in Italy
738697-061
For use in Japan
738697-291
For use in Latin America
738697-161
For use in the Netherlands
738697-B31
For use in Northwest Africa
738697-FP1
For use in Norway
738697-091
For use in Portugal
738697-131
For use in Romania
738697-271
For use in Russia
738697-251
Computer major components
25
Item
Component
Spare part number
For use in Saudi Arabia
738697-171
For use in Slovenia
738697-BA1
For use in South Korea
738697-AD1
For use in Spain
738697-071
For use in Sweden and Finland
738697-B71
For use in Switzerland
738697-BG1
For use in Taiwan
738697-AB1
For use in Thailand
738697-281
For use in Turkey
738697-141
For use in the United Kingdom and Singapore
738697-031
For use in the United States
738697-001
Backlit keyboard for 15.6-in models (includes backlight and keyboard cables):
26
For use in Belgium
787801-A41
For use in Brazil
787801-201
For use in Bulgaria
787801-261
For use in Canada
787801-DB1
For use in the Czech Republic and Slovakia
787801-FL1
For use in Denmark
787801-081
For use in France
787801-051
For use in Germany
787801-041
For use in Greece
787801-151
For use in Hungary
787801-211
For use in Iceland
787801-DD1
For use in India
787801-D61
For use in Israel
787801-BB1
For use in Italy
787801-061
For use in Japan
787801-291
For use in Latin America
787801-161
For use in the Netherlands
787801-B31
For use in Northwest Africa
787801-FP1
For use in Norway
787801-091
For use in Portugal
787801-131
For use in Romania
787801-271
For use in Russia
787801-251
Chapter 3 Illustrated parts catalog
Item
Component
Spare part number
For use in Saudi Arabia
787801-171
For use in Slovenia
787801-BA1
For use in South Korea
787801-AD1
For use in Spain
787801-071
For use in Sweden and Finland
787801-B71
For use in Switzerland
787801-BG1
For use in Taiwan
787801-AB1
For use in Thailand
787801-281
For use in Turkey
787801-141
For use in the United Kingdom and Singapore
787801-031
For use in the United States
787801-001
Keyboard for 15.6-in models (includes keyboard cable):
For use in Belgium
738696-A41
For use in Brazil
738696-201
For use in Bulgaria
738696-261
For use in Canada
738696-DB1
For use in the Czech Republic and Slovakia
738696-FL1
For use in Denmark
738696-081
For use in France
738696-051
For use in Germany
738696-041
For use in Greece
738696-151
For use in Hungary
738696-211
For use in Iceland
738696-DD1
For use in India
738696-D61
For use in Israel
738696-BB1
For use in Italy
738696-061
For use in Japan
738696-291
For use in Latin America
738696-161
For use in the Netherlands
738696-B31
For use in Northwest Africa
738696-FP1
For use in Norway
738696-091
For use in Portugal
738696-131
For use in Romania
738696-271
For use in Russia
738696-251
Computer major components
27
Item
Component
Spare part number
For use in Saudi Arabia
738696-171
For use in Slovenia
738696-BA1
For use in South Korea
738696-AD1
For use in Spain
738696-071
For use in Sweden and Finland
738696-B71
For use in Switzerland
738696-BG1
For use in Taiwan
738696-AB1
For use in Thailand
738696-281
For use in Turkey
738696-141
For use in the United Kingdom and Singapore
738696-031
For use in the United States
738696-001
Keyboard for 14” models with pointing stick (includes keyboard cable and pointing stick cable):
28
For use in Belgium
738688-A41
For use in Brazil
738688-201
For use in Bulgaria
738688-261
For use in Canada
738688-DB1
For use in the Czech Republic and Slovakia
738688-FL1
For use in Denmark
738688-081
For use in France
738688-051
For use in Germany
738688-041
For use in Greece
738688-151
For use in Hungary
738688-211
For use in Iceland
738688-DD1
For use in India
738688-D61
For use in Israel
738688-BB1
For use in Italy
738688-061
For use in Japan
738688-291
For use in Latin America
738688-161
For use in the Netherlands
738688-B31
For use in Northwest Africa
738688-FP1
For use in Norway
738688-091
For use in Portugal
738688-131
For use in Romania
738688-271
For use in Russia
738688-251
Chapter 3 Illustrated parts catalog
Item
Component
Spare part number
For use in Saudi Arabia
738688-171
For use in Slovenia
738688-BA1
For use in South Korea
738688-AD1
For use in Spain
738688-071
For use in Sweden and Finland
738688-B71
For use in Switzerland
738688-BG1
For use in Taiwan
738688-AB1
For use in Thailand
738688-281
For use in Turkey
738688-141
For use in the United Kingdom and Singapore
738688-031
For use in the United States
738688-001
Backlit keyboard for 14-in models (includes backlight and keyboard cables):
For use in Belgium
787294-A41
For use in Brazil
787294-201
For use in Bulgaria
787294-261
For use in Canada
787294-DB1
For use in the Czech Republic and Slovakia
787294-FL1
For use in Denmark
787294-081
For use in France
787294-051
For use in Germany
787294-041
For use in Greece
787294-151
For use in Hungary
787294-211
For use in Iceland
787294-DD1
For use in India
787294-D61
For use in Israel
787294-BB1
For use in Italy
787294-061
For use in Japan
787294-291
For use in Latin America
787294-161
For use in the Netherlands
787294-B31
For use in Northwest Africa
787294-FP1
For use in Norway
787294-091
For use in Portugal
787294-131
For use in Romania
787294-271
For use in Russia
787294-251
Computer major components
29
Item
Component
Spare part number
For use in Saudi Arabia
787294-171
For use in Slovenia
787294-BA1
For use in South Korea
787294-AD1
For use in Spain
787294-071
For use in Sweden and Finland
787294-B71
For use in Switzerland
787294-BG1
For use in Taiwan
787294-AB1
For use in Thailand
787294-281
For use in Turkey
787294-141
For use in the United Kingdom and Singapore
787294-031
For use in the United States
787294-001
Keyboard for 14” models (includes keyboard cable):
30
For use in Belgium
738687-A41
For use in Bulgaria
738687-261
For use in Canada
738687-DB1
For use in the Czech Republic and Slovakia
738687-FL1
For use in Denmark
738687-081
For use in France
738687-051
For use in Germany
738687-041
For use in Greece
738687-151
For use in Hungary
738687-211
For use in Iceland
738687-DD1
For use in India
738687-D61
For use in Israel
738687-BB1
For use in Italy
738687-061
For use in Japan
738687-291
For use in Latin America
738687-161
For use in the Netherlands
738687-B31
For use in Northwest Africa
738687-FP1
For use in Norway
738687-091
For use in Portugal
738687-131
For use in Romania
738687-271
For use in Russia
738687-251
For use in Saudi Arabia
738687-171
Chapter 3 Illustrated parts catalog
Item
Component
Spare part number
For use in Slovenia
738687-BA1
For use in South Korea
738687-AD1
For use in Spain
738687-071
For use in Sweden and Finland
738687-B71
For use in Switzerland
738687-BG1
For use in Taiwan
738687-AB1
For use in Thailand
738687-281
For use in Turkey
738687-141
For use in the United Kingdom and Singapore
738687-031
For use in the United States
738687-001
(4)
Power connector board
(5)
Top cover
(6)
(7)
Top cover and 2-button TouchPad for HP ProBook 655 G1 models
745889–001
Top cover and 4-button TouchPad for HP ProBook 655 G1 models
745890–001
Top cover and 2-button TouchPad for HP ProBook 655 G1 models equipped with a backlit
keyboard
805782–001
Top cover and 2-button TouchPad for HP ProBook 650 G1 models
738708-001
Top cover and 4-button TouchPad for HP ProBook 650 G1 models
738709–001
Top cover and 2-button TouchPad for HP ProBook 650 G1 models equipped with a backlit
keyboard
805787–001
Top cover and 2-button TouchPad for models equipped with a 14–inch display assembly
738405-001
Top cover and 4-button TouchPad for models equipped with a 14–inch display assembly
738406–001
Top cover and 2-button TouchPad for models equipped with a 14–inch display assembly
and a backlit keyboard
805783–001
Smart card reader (includes cable)
For use in models equipped with a 15.6–inch display assembly
748958–001
Smart Card reader for models equipped with a 2-button TouchPad and a 14–inch display
assembly
738398-001
Smart Card reader for models equipped with a 4-button TouchPad and a 14–inch display
assembly
744005-001
Power button board (includes cable)
For 15.6-in models
738701-001
For 14-in models
738399-001
(8)
Speakers (include cable)
738404-001
(9)
Wireless card
(10)
Smart card reader shield (select models only) (included with smart card reader)
Computer major components
31
Item
Component
(11)
Fingerprint reader bracket (included with fingerprint reader)
(12)
Fingerprint reader board (includes cable and double-sided adhesive)
(13)
TouchPad (includes TouchPad,TouchPad cable, and TouchPad bracket)
(14)
(15)
(16)
(17)
32
Spare part number
738394-001
For 15.6-in models with 2-button TouchPad
738710-001
For 15.6-in models with 4-button TouchPad
738711-001
Top cover and 2-button TouchPad for models equipped with a 14–inch display assembly
738405-001
Top cover and 4-button TouchPad for models equipped with a 14–inch display assembly
738406-001
Audio/USB board
For use in ProBook 655 G1 models equipped with a 15.6–inch display assembly
745891-001
For use in ProBook 650 G1 models equipped with a 15.6–inch display assembly
738702-001
For use in computer models equipped with a 14–inch display assembly
738400-001
Processor (includes replacement thermal material):
Intel Dual Core i7-4600M 2.80-GHz processor (4.0-MB L3 cache, 37 W)
737330-001
Intel Dual Core i5-4330M 2.80-GHz processor (3.0-MB L3 cache, 37 W)
738201-001
Intel Dual Core i5-4300M 2.60-GHz processor (3.0-MB L3 cache, 37 W)
738309-001
Intel Dual Core i5-4200M 2.50-GHz processor (3.0-MB L3 cache, 37 W)
737328-001
Intel Dual Core i3-4100M 2.50-GHz processor (3.0-MB L3 cache, 37 W)
737474-001
Intel Dual Core i3-4000M 2.40-GHz processor (3.0-MB L3 cache, 37 W)
737327-001
AMD A10-5750M with Radeon HD 8650G Graphics (quad-core; 3.5 GHz/2.5 GHz; 35W, 4 MB
L2 cache)
713548-001
AMD A10-4600M with Radeon HD 7660G Graphics (quad-core; 3.2 GHz/2.3 GHz; 35W; 4 MB
L2 cache)
683046-001
AMD A8-4500M with Radeon HD 7640G Graphics (quad-core; 2.8 GHz/1.9 GHz; 35W; 4 MB
L2 cache)
683048-001
AMD A6-4400M with Radeon HD 7520G Graphics (dual-core; 3.2 GHz/2.7 GHz; 35W; 1 MB L2
cache)
683047-001
AMD A6-5350M with Radeon HD 8450G Graphics (dual-core; 3.5 GHz/2.9 GHz; 35W; 1 MB L2
cache)
713550-001
AMD A4-4300M with Radeon HD 7420G Graphics (dual-core; 3.0 GHz/2.5 GHz; 35W; 1 MB L2
cache)
685990-001
AMD A4-5150M with Radeon HD 8350G Graphics (dual-core; 3.3 GHz/2.7 GHz; 35W; 1 MB L2
cache)
713549-001
AMD A8-5550M Quad Core 3.1 GHz/2.1 GHz
713551-001
Function button board (includes cable and double-sided adhesive)
For use in computer models equipped with a 14–inch display assembly
738401-001
For use in computer models equipped with a 15.6–inch display assembly
738703-001
System board (includes battery connector bracket and replacement thermal material):
Chapter 3 Illustrated parts catalog
Item
Component
Spare part number
System board for 14-in. computer models equipped with shared memory and the Windows
8 Standard operating system with WWAN capability (includes replacement thermal
material)
744007-001
System board for 14-in. computer models equipped with shared memory and the Windows
8 Standard operating system with WWAN capability (includes replacement thermal
material)
744007-501
System board for 14-in. computer models equipped with shared memory and the Windows
8 Professional operating system with WWAN capability (includes replacement thermal
material)
744007-601
System board for 14-in. computer models equipped with discrete memory and WWAN
capability (includes replacement thermal material)
744008-001
System board for 14-in. computer models equipped with discrete memory and the
Windows 8 Standard operating system with WWAN capability (includes replacement
thermal material)
744008-501
System board for 14-in. computer models equipped with discrete memory and the
Windows 8 Professional operating system with WWAN capability (includes replacement
thermal material)
744008-601
System board for 14-in. computer models equipped with discrete memory, WWAN
capability (includes replacement thermal material)
744009-001
System board for 14-in. computer models equipped with discrete memory and the
Windows 8 Standard operating system with WWAN capability (includes replacement
thermal material)
744009-501
System board for 14-in. computer models equipped with shared memory and the Windows
8 Professional operating system with WWAN capability (includes replacement thermal
material)
744009-601
System board for 14-in. computer models equipped with discrete memory and WWAN
capability (includes replacement thermal material)
744010-001
System board for 14-in. computer models equipped with discrete memory and the
Windows 8 Standard operating system with WWAN capability (includes replacement
thermal material)
744010-501
System board for 14-in. computer models equipped with shared memory and the Windows
8 Professional operating system with WWAN capability (includes replacement thermal
material)
744010-601
System board for 15.6-in. computer models equipped with discrete memory, WWAN
capability (includes replacement thermal material)
744015-001
System board for 15.6-in. computer models equipped with discrete memory and the
Windows 8 Standard operating system with WWAN capability (includes replacement
thermal material)
744015-501
System board for 15.6-in. computer models equipped with shared memory and the
Windows 8 Professional operating system with WWAN capability (includes replacement
thermal material)
744015-601
System board for 15.6-in. computer models equipped with shared memory with WWAN
capability (includes replacement thermal material)
744015-001
System board for 15.6-in. computer models equipped with shared memory and the
Windows 8 Standard operating system with WWAN capability (includes replacement
thermal material)
744015-501
Computer major components
33
Item
34
Component
Spare part number
System board for 15.6-in. computer models equipped with shared memory and the
Windows 8 Professional operating system with WWAN capability (includes replacement
thermal material)
744015-601
System board for 15.6-in. computer models equipped with shared memory, WWAN
capability, and a modem (includes replacement thermal material)
744016-001
System board for 15.6-in. computer models equipped with shared memory and the
Windows 8 Standard operating system with WWAN capability and a modem (includes
replacement thermal material)
744016-501
System board for 15.6-in. computer models equipped with shared memory and the
Windows 8 Professional operating system with WWAN capability and a modem (includes
replacement thermal material)
744016-601
System board for 15.6-in. computer models equipped with discrete memory with WWAN
capability (includes replacement thermal material)
744017-001
System board for 15.6-in. computer models equipped with discrete memory and the
Windows 8 Standard operating system with WWAN capability (includes replacement
thermal material)
744017-501
System board for 15.6-in. computer models equipped with discrete memory and the
Windows 8 Professional operating system with WWAN capability (includes replacement
thermal material)
744017-601
System board for 15.6-in. computer models equipped with discrete memory with WWAN
capability and a modem (includes replacement thermal material)
744018-001
System board for 15.6-in. computer models equipped with discrete memory and the
Windows 8 Standard operating system with WWAN capability and a modem (includes
replacement thermal material)
744018-501
System board for 15.6-in. computer models equipped with discrete memory and the
Windows 8 Professional operating system with WWAN capability and a modem (includes
replacement thermal material)
744018-601
System board for 15.6-in. computer models equipped with shared memory, WWAN
capability (includes replacement thermal material)
744019-001
System board for 15.6-in. computer models equipped with shared memory and the
Windows 8 Standard operating system with WWAN capability (includes replacement
thermal material)
744019-501
System board for 15.6-in. computer models equipped with shared memory and the
Windows 8 Professional operating system with WWAN capability (includes replacement
thermal material)
744019-601
System board for 15.6-in. computer models equipped with shared memory, WWAN
capability and a modem (includes replacement thermal material)
744020-001
System board for 15.6-in. computer models equipped with shared memory and the
Windows 8 Standard operating system with WWAN capability and a modem (includes
replacement thermal material)
744020-501
System board for 15.6-in. computer models equipped with shared memory and the
Windows 8 Professional operating system with WWAN capability and a modem (includes
replacement thermal material)
744020-601
System board for 15.6-in. computer models equipped with discrete memory, WWAN
capability (includes replacement thermal material)
744021-001
System board for 15.6-in. computer models equipped with discrete memory and the
Windows 8 Standard operating system with WWAN capability (includes replacement
thermal material)
744021-501
Chapter 3 Illustrated parts catalog
Item
(18)
Component
Spare part number
System board for 15.6-in. computer models equipped with discrete memory and the
Windows 8 Professional operating system with WWAN capability (includes replacement
thermal material)
744021-601
System board for 15.6-in. computer models equipped with discrete memory, WWAN
capability and a modem (includes replacement thermal material)
744022-001
System board for 15.6-in. computer models equipped with discrete memory and the
Windows 8 Standard operating system with WWAN capability and a modem (includes
replacement thermal material)
744022-501
System board for 15.6-in. computer models equipped with discrete memory and the
Windows 8 Professional operating system with WWAN capability and a modem (includes
replacement thermal material)
744022-601
For use only 14-in. computer models equipped with an Intel Quad Core processor with
WWAN capability
745883-001
For use only on 14-in. computer models equipped with shared memory and the Windows 8
Standard operating system with WWAN capability
745883-501
For use only on 14-in. computer models equipped with shared memory and the Windows 8
Professional operating system with WWAN capability
745883-601
For use only 14-in. computer models equipped with shared memory without WWAN
capability
745884-001
For use only on 14-in. computer models equipped with shared memory and the Windows 8
Standard operating system without WWAN capability
745884-501
For use only on 14-in. computer models equipped with shared memory, the Windows 8
Professional operating system without WWAN capability
745884-601
For use only on 15.6-in. computer models equipped with shared memory and WWAN
capability
745887-001
For use only on 15.6-in. computer models equipped with shared memory and the Windows
8 Standard operating system and WWAN capability
745887-501
For use only on 15.6-in. computer models equipped with shared memory and the Windows
8 Professional operating system with WWAN capability
745887-601
For use only on 15.6-in computer models equipped with shared memory without WWAN
capability
745888-001
For use only on 15.6-in computer models equipped with shared memory and the Windows
8 Standard operating system without WWAN capability
745888-501
For use only on 15.6-in computer models equipped with shared memory and the Windows
8 Professional operating system without WWAN capability
745888-601
Optical drive (includes bezel and bracket):
Blu-ray R/RE DVD±RW SuperMulti Double-Layer Combo Drive
749959-001
739999-001
744820-001
DVD±RW SuperMulti Double-Layer Drive
749958-001
744822-001
740001-001
DVD-ROM Drive
749957-001
Computer major components
35
Item
Component
Spare part number
744821-001
740000-001
735601-001
Fan and heat sink assembly (includes replacement thermal material):
(19)
Fan
738685-001
(20)
Heat sink for computer models with Intel UMA graphics memory
738686-001
(22)
Heat sink for computer models with discrete graphics
738393-001
(21)
Fingerprint reader bracket
738394
(23)
Base enclosure (includes 4 rubber feet, battery lock latch, battery release latch, and RJ-45
cover)
(24)
738681-001
For 15.6-in models
738692-001
Power connector cable
For use on models equipped with a 15.6–inch display assembly
738694–001
For use on models equipped with a 14–inch display assembly
738683–001
(25)
Modem (select models only)
628824-001
(26)
WLAN module:
(27)
(28)
36
For 14-in models
Intel 802.11 2x2 a/b/g/n
695915-001
Intel 802.11 2x2 a/b/g/n Combo Adapter
670292-001
Atheros 802.11 b/g/n 1x1
690019-001
Intel 802.11 2x2 AC + Bluetooth 4.0
710661-001
Intel 802.11 2x2 AC + Bluetooth 4.0
717381-001
Intel 802.11 a/b/g/n 2x2 + Bluetooth 4.0 WLAN
710661-001
Broadcom 802.11 a/b/g/n 2x2 + BT 4.0 LE PCIe+USB HMC WW
730668-001
Intel 802.11 a/b/g/n 2x2 + BT 4.0 WLAN
747832-001
Solid-state drive
512-GB SATA-3 SSD
738714-001
256-GB SATA-3 self-encrypting SSD
735598-001
180-GB SATA-3 SSD
735597-001
128-GB SATA-3 SSD
735596-001
128-GB mSATA-3 SSD
735595-001
32-GB mSATA flash cache SSD
735594-001
Hard drive (does not include hard drive bracket or screws):
1-TB, 5400-rpm, 9.5-mm
676521-001
750-GB, 7200-rpm, 7.0-mm
633252-001
Chapter 3 Illustrated parts catalog
Item
(29)
(30)
(31)
Component
Spare part number
500-GB, 7200-rpm, 7.0-mm
703267-001
500-GB, 5400-rpm, 7.0-mm, FIPS
730946-001
500-GB, 7200-rpm, 7.0-mm, self-encrypting
703268-001
320-GB, 7200-rpm, 7.0-mm
634862-001
Hard Drive Hardware Kit (not illustrated, includes hard drive bracket and screws)
738395-001
WWAN module (select models only)
HP hs3110 HSPA+ Mobile Broadband Module
723895-001
HP lt4111 LTE/EV-DO/HSPA+ Mobile Broadband Module
704030-001
HP lt4112 LTE/HSPA+ Mobile Broadband Module
704031-001
Battery:
9-cell, 100-WHr, 3.0-AHr, Li-ion battery
718757-001
6-cell, 55-WHr, 2.8-AHr, Li-ion battery
718756-001
6-cell, 55-WHr, 2.5-AHr, Li-ion battery
718755-001
3-cell, 33-WHr, 2.0-AHr, Li-ion battery
718754-001
Service cover
Service cover for use on computer models equipped with a 15.6-inch display assembly
738693-001
Service cover for use on computer models equipped with a 15.6-inch display assembly and
which meet regional configure to order (RCTO) specifications
748358-001
Service cover for use on computer models equipped with a 14-inch display assembly
738682-001
Service cover for use on computer models equipped with a 14-inch display assembly and
which meet regional configure to order (RCTO) specifications
748357-001
Computer major components
37
Display assembly subcomponents
Item
Component
(1)
Display bezel:
(2)
(3)
38
Spare part number
For use only on 15.6-in computer models
738690-001
For use only on 14-in computer models
738679-001
Webcamera/microphone module (includes double-sided adhesive)
738409-001
Microphone module (includes double-sided adhesive)
738397-001
Display panel:
15.6-in WLED FHD, UWVA
739998-001
15.6-in WLED HD, SVA
739997-001
14-in WLED FHD, UWVA
747753-001
Chapter 3 Illustrated parts catalog
Item
Component
Spare part number
14-in WLED HD, SVA
747752-001
14-in WLED HD, SVA
747751-001
Raw Panel Support Kit (includes LCD back cover and wireless antennas and transceivers):
(4) and
(6)
(5)
For use in models equipped with a 15.6–inch display assembly
738691-001
For use in models equipped with a 14–inch display assembly
738680–001
Display hinge kit (includes left and right hinges and display panel cable bracket)
For 15.6-in computer models
738699-001
For 14-in computer models
738396-001
Display Cable Kit (includes display panel cable)
For use on HP ProBook 655 G1 models equipped with a 15.6-inch display assembly
745892-001
For use on HP ProBook 650 G1 models equipped with a 15.6-inch display assembly
744013-001
For use on computer models equipped with a 14-inch display assembly
738684-001
Item
Component
Spare part number
(1)
RJ-45 (network) cable
(2)
Power connector cable
Cables
Cable Kit (includes the RJ-45 (network) cable, power connector cable, and replacement
thermal material for the models listed below):
Cables
39
Item
Component
Spare part number
For use on HP ProBook 650 G1 computer models equipped with a 15.6-inch display
assembly
744013–001
For use on HP ProBook 655 G1 computer models equipped with a 15.6-inch display
assembly
745892-001
For use on computer models equipped with a 14-inch display assembly
738684-001
Component
Spare part number
Plastics Kit
Item
Plastics Kit, includes:
40
For 14-in models
738402-001
For 15.6-in models
738706-001
(1)
Fingerprint bracket
(2)
Smart card reader blank
(3)
WLAN bracket
(4)
Fingerprint reader bezel
(5)
SD card reader bezel
(6)
Optical drive blank tray
Chapter 3 Illustrated parts catalog
Mass storage devices
Item
Component
(1)
Solid-state drive (SSD):
Spare part number
256-GB SATA-3 self-encrypting SSD
749263-001
180-GB SATA-3 SSD
749262-001
749278-001
128-GB SATA-3 SSD
749261-001
749277-001
(2)
128-GB mSATA-3 SSD
749280-0011
32-GB mSATA flash cache SSD
7749281-001
Hard Drive Hardware Kit, includes:
738395-001
Hard drive bracket
Screws (not illustrated)
(3)
Hard drive (does not include hard drive bracket or screws):
1-TB, 5400-rpm, 9.5-mm
676521-001
750-GB, 7200-rpm, 7.0-mm
633252-001
500-GB, 7200-rpm, 7.0-mm
703267-001
500-GB, 5400-rpm, 7.0-mm, FIPS
730946-001
Mass storage devices
41
Item
(4)
Component
Spare part number
500-GB, 7200-rpm, 7.0-mm, self-encrypting
703268-001
320-GB, 7200-rpm, 7.0-mm
634862-001
Optical drive (includes bezel and bracket):
Blu-ray R/RE DVD±RW SuperMulti Double-Layer Combo Drive
749959-001
739999-001
744820-001
DVD±RW SuperMulti Double-Layer Drive
749958-001
744822-001
740000-001
DVD-ROM Drive
749957-001
744821-001
740001-001
735601-001
Miscellaneous parts
Component
Spare part number
AC adapter:
65-W HP Smart adapter (PFC, 3-wire, 4.5-mm)
693710-001
65-W HP Smart adapter (PFC, 3-wire, 4.5-mm)
693711-001
90-W HP Smart adapter (PFC, 3-wire, 4.5-mm)
693712-001
90-W HP Smart adapter (PFC, 3-wire, 4.5-mm)
693713-001
Power cord (3-pin, black, 1.83-m):
42
For use in Argentina
490371-D01
For use in Australia
490371-011
For use in Brazil
490371-202
For use in Europe
490371-021
For use in India
490371-D61
For use in Israel
490371-BB1
For use in Italy
490371-061
For use in Japan
490371-291
For use in North America
490371-001
For use in the People's Republic of China
490371-AA1
For use in South Africa
490371-AR1
For use in South Korea
490371-AD1
Chapter 3 Illustrated parts catalog
Component
Spare part number
For use in Switzerland
490371-111
For use in Taiwan
490371-AB1
For use in Thailand
490371-201
For use in the United Kingdom and Singapore
490371-031
Screw Kit
738689-001
Sequential part number listing
Spare part number
Description
490371-001
Power cord for use in North America (3-pin, black, 1.83-m)
490371-011
Power cord for use in Australia (3-pin, black, 1.83-m)
490371-021
Power cord for use in Europe (3-pin, black, 1.83-m)
490371-031
Power cord for use in the United Kingdom and Singapore (3-pin, black, 1.83-m)
490371-061
Power cord for use in Italy (3-pin, black, 1.83-m)
490371-111
Power cord for use in Switzerland (3-pin, black, 1.83-m)
490371-201
Power cord for use in Thailand (3-pin, black, 1.83-m)
490371-202
Power cord for use in Brazil (3-pin, black, 1.83-m)
490371-291
Power cord for use in Japan (3-pin, black, 1.83-m)
490371-AA1
Power cord for use in the People's Republic of China (3-pin, black, 1.83-m)
490371-AB1
Power cord for use in Taiwan (3-pin, black, 1.83-m)
490371-AD1
Power cord for use in South Korea (3-pin, black, 1.83-m)
490371-AR1
Power cord for use in South Africa (3-pin, black, 1.83-m)
490371-BB1
Power cord for use in Israel (3-pin, black, 1.83-m)
490371-D01
Power cord for use in Argentina (3-pin, black, 1.83-m)
490371-D61
Power cord for use in India (3-pin, black, 1.83-m)
603783-001
320-GB, 7200-rpm, SATA, 7.0-mm hard drive (does not include hard drive bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
628824-001
Modem (select models only)
633252-001
750-GB, 7200-rpm, SATA, 2.5-in hard drive (does not include hard drive bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
634862-001
320-GB, 7200-rpm, SATA, 7.0-mm hard drive (does not include hard drive bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
634921-001
500GB, 7200-rpm, SATA, 2.5-in hard drive (does not include hard drive bracket or screws)
Sequential part number listing
43
Spare part number
Description
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
634925-001
500GB, 7200-rpm, SATA, 2.5-in hard drive (does not include hard drive bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
651948-001
RTC battery (includes cable and double-sided adhesive)
670292-001
Intel 802.11 a/b/g/n 2x2 Combo Adapter
675794-001
Intel 802.11 b/g/n HMC 1x1
676521-001
1-TB, 5400-rpm, SATA, 9.5-mm hard drive (does not include hard drive bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
683046-001
AMD A10-4600M with Radeon HD 7660G Graphics (quad-core; 3.2 GHz/2.3 GHz; 35W; 4 MB L2 cache)
683047-001
AMD A6-4400M with Radeon HD 7520G Graphics (dual-core; 3.2 GHz/2.7 GHz; 35W; 1 MB L2 cache)
683048-001
AMD A8-4500M with Radeon HD 7640G Graphics (quad-core; 2.8 GHz/1.9 GHz; 35W; 4 MB L2 cache)
683801-001
500-GBB, 7200-rpm, SATA, self–encrypting hard drive 9.5-mm hard drive (does not include hard drive
bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
683802-001
500-GBB, 5400-rpm, SATA, hard drive 7-mm hard drive (does not include hard drive bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
685990-001
Processor A4-4300M 3.0/2.5 GHz 35W 1M
685990-001
750-GBB, 7200-rpm, SATA hard drive 2.5-in hard drive (does not include hard drive bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
686850-001
750-GBB, 7200-rpm, SATA hard drive 2.5-in hard drive (does not include hard drive bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
44
688169-001
Dock/expansion base (select models only)
690019-001
Atheros 802.11 b/g/n 1x1
691739-001
2-GB memory module (PC3L, 12800, 1600-MHz)
691740-001
4-GB memory module (PC3L, 12800, 1600-MHz)
691922-001
HP comfort grip wireless mouse
693374-001
8-GB memory module (PC3L, 12800, 1600-MHz)
693710-001
65-W HP Smart adapter (PFC, 3-wire, 4.5-mm)
693711-001
65-W HP Smart adapter (PFC, 3-wire, 4.5-mm)
693712-001
90-W HP Smart adapter (PFC, 3-wire, 4.5-mm)
693713-001
90-W HP Smart adapter (PFC, 3-wire, 4.5-mm)
Chapter 3 Illustrated parts catalog
Spare part number
Description
695915-001
Intel 802.11 2x2 a/b/g/n
703267-001
500-GB, 7200-rpm, SATA, 7.0-mm hard drive (does not include hard drive bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
703268-001
500-GB, 7200-rpm, SATA, 7.0-mm self-encrypting drive (SED, does not include hard drive bracket or
screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
704030-001
HP lt4111 LTE/EV-DO/HSPA+ Mobile Broadband Module
704031-001
HP lt4112 LTE/HSPA+ Mobile Broadband Module
710661-001
Intel 802.11 2x2 AC + Bluetooth 4.0
713548-001
AMD A10-5750M with Radeon HD 8650G Graphics (quad-core; 3.5 GHz/2.5 GHz; 35W, 4 MB L2 cache)
713549-001
AMD A4-5150M with Radeon HD 8350G Graphics (dual-core; 3.3 GHz/2.7 GHz; 35W; 1 MB L2 cache)
713550-001
A6-5350M with Radeon HD 8450G Graphics (dual-core; 3.5 GHz/2.9 GHz; 35W; 1 MB L2 cache)
713551-001
AMD A8-5550M Quad Core 3.1 GHz/2.1 GHz HD8550G
717381-001
Intel 802.11 a/b/g/n 2x2 + Bluetooth 4.0 WLAN
718754-001
3-cell, 33-WHr, 2.0-AHr, Li-ion battery
718755-001
6-cell, 55-WHr, 2.55-AHr, Li-ion battery
718756-001
6-cell, 55-WHr, 2.8-AHr, Li-ion battery
718757-001
9-cell, 100-WHr, 3.0-AHr, Li-ion battery
723895-001
HP hs3110 HSPA+ Mobile Broadband Module
730668-001
Broadcom 802.11 a/b/g/n 2x2 + BT 4.0 LE PCIe+USB HMC WW
730946-001
500-GB, 5400-rpm, SATA, 7.0-mm FIPS hard drive (does not include hard drive bracket or screws)
NOTE: The hard drive bracket and screws are included in the Hard Drive Hardware Kit, spare part
number 738395-001.
735400-001
USB board (includes cable and double-sided adhesive)
735401-001
Function button board (includes cable and double-sided adhesive)
735402-001
Plastics kit
735404-001
Speaker kit
735405-001
Top cover and 2-button TouchPad for 14-in models
735406-001
Top cover and 4-button TouchPad for 14-in models
735407-001
TouchPad bracket with 2 buttons
735408-001
TouchPad bracket with 4 buttons
735409-001
Webcamera/microphone module (includes double-sided adhesive)
737327-001
Intel Dual Core i3-4000M 2.40-GHz processor (3.0- MB L3 cache, 37 W)
737328-001
Intel Dual Core i5-4200M 2.50-GHz processor ( 3.0- MB L3 cache, 37 W)
Sequential part number listing
45
46
Spare part number
Description
737330-001
Intel Dual Core i7 4600M 2.8 GHz (3MB 37W)
737474-001
Intel Dual Core i3-4100M 2.50-GHz processor (3.0- MB L3 cache, 37 W)
738201-001
Intel Dual Core i5-4330M 2.80-GHz processor (3.0- MB L3 cache, 37 W)
738309-001
Intel Dual Core i5-4300M 2.60-GHz processor ( 3.0-MB L3 cache, 37 W)
738393-001
Heat sink assembly for models with discrete memory
738394-001
Fingerprint reader (includes cable)
738395-001
Hard drive hardware kit
738396-001
Display hinge kit
738397-001
Microphone module (includes double-sided adhesive)
738398-001
Smart card reader for 14-in models with 2-button TouchPad (includes cable)
738399-001
Power button board (includes cable)
738400–001
USB board for use in computer models equipped with a 14–inch display assembly (includes cable)
738401–001
Function button board for use in models equipped with a 14–inch display assembly (includes cable)
738403-001
Rubber kit
738679-001
Display bezel for 14-in models
738680-001
Raw Panel Support Kit for 14-in models (includes wireless antennas and transceivers)
738681-001
Base enclosure for 14-in models
738682-001
Service cover for use on computer models equipped with a 14–inch display assembly
738683-001
Power connector cable for use on models equipped with a 14–inch display assembly
738684-001
Display cable kit for 14-in models (includes display panel cable)
738685-001
Fan
738686-001
Heat sink for computer models with Intel UMA graphics memory
738687-001
Keyboard for 14-in models for use in the United States (includes keyboard cable)
738687-031
Keyboard for 14-in models for use in the United Kingdom and Singapore (includes keyboard cable)
738687-041
Keyboard for 14-in models for use in Germany (includes keyboard cable)
738687-051
Keyboard for 14-in models for use in France (includes keyboard cable)
738687-061
Keyboard for 14-in models for use in Italy (includes keyboard cable)
738687-071
Keyboard for 14-in models for use in Spain (includes keyboard cable)
738687-081
Keyboard for 14-in models for use in Denmark (includes keyboard cable)
738687-091
Keyboard for 14-in models for use in Norway (includes keyboard cable)
738687-131
Keyboard for 14-in models for use in Portugal (includes keyboard cable)
738687-141
Keyboard for 14-in models for use in Turkey (includes keyboard cable)
738687-151
Keyboard for 14-in models for use in Greece (includes keyboard cable)
738687-161
Keyboard for 14-in models for use in Latin America (includes keyboard cable)
Chapter 3 Illustrated parts catalog
Spare part number
Description
738687-171
Keyboard for 14-in models for use in Saudi Arabia (includes keyboard cable)
738687-211
Keyboard for 14-in models for use in Hungary (includes keyboard cable)
738687-251
Keyboard for 14-in models for use in Russia (includes keyboard cable)
738687-261
Keyboard for 14-in models for use in Bulgaria (includes keyboard cable)
738687-271
Keyboard for 14-in models for use in Romania (includes keyboard cable)
738687-281
Keyboard for 14-in models for use in Thailand (includes keyboard cable)
738687-291
Keyboard for 14-in models for use in Japan (includes keyboard cable)
738687-A41
Keyboard for 14-in models for use in Belgium (includes keyboard cable)
738687-AB1
Keyboard for 14-in models for use in Taiwan (includes keyboard cable)
738687-AD1
Keyboard for 14-in models for use in South Korea (includes keyboard cable)
738687-B31
Keyboard for 14-in models for use in the Netherlands (includes keyboard cable)
738687-B71
Keyboard for 14-in models for use in Sweden (includes keyboard cable)
738687-BA1
Keyboard for 14-in models for use in Slovenia (includes keyboard cable)
738687-BB1
Keyboard for 14-in models for use in Israel (includes keyboard cable)
738687-BG1
Keyboard for 14-in models for use in Switzerland (includes keyboard cable)
738687-D61
Keyboard for 14-in models for use in India (includes keyboard cable)
738687-DB1
Keyboard for 14-in models for use in Canada (includes keyboard cable)
738687-DD1
Keyboard for 14-in models for use in Iceland (includes keyboard cable)
738687-FL1
Keyboard for 14-in models for use in the Czech Republic and Slovakia (includes keyboard cable)
738687-FP1
Keyboard for 14-in models for use in Northwest Africa (includes keyboard cable)
738688-001
Keyboard with pointing stick for 14-in models for use in the United States (includes keyboard cable and
pointing stick cable)
738688-031
Keyboard with pointing stick for 14-in models for use in the United Kingdom and Singapore (includes
keyboard cable and pointing stick cable)
738688-041
Keyboard with pointing stick for 14-in models for use in Germany (includes keyboard cable and pointing
stick cable)
738688-051
Keyboard with pointing stick for 14-in models for use in France (includes keyboard cable and pointing
stick cable)
738688-061
Keyboard with pointing stick for 14-in models for use in Italy (includes keyboard cable and pointing stick
cable)
738688-071
Keyboard with pointing stick for 14-in models for use in Spain (includes keyboard cable and pointing stick
cable)
738688-081
Keyboard with pointing stick for 14-in models for use in Denmark (includes keyboard cable and pointing
stick cable)
738688-091
Keyboard with pointing stick for 14-in models for use in Norway (includes keyboard cable and pointing
stick cable)
738688-131
Keyboard with pointing stick for 14-in models for use in Portugal (includes keyboard cable and pointing
stick cable)
Sequential part number listing
47
48
Spare part number
Description
738688-141
Keyboard with pointing stick for 14-in models for use in Turkey (includes keyboard cable and pointing
stick cable)
738688-151
Keyboard with pointing stick for 14-in models for use in Greece (includes keyboard cable and pointing
stick cable)
738688-161
Keyboard with pointing stick for 14-in models for use in Latin America (includes keyboard cable and
pointing stick cable)
738688-171
Keyboard with pointing stick for 14-in models for use in Saudi Arabia(includes keyboard cable and
pointing stick cable)
738688-201
Keyboard with pointing stick for 14-in models for use in Brazil (includes keyboard cable and pointing stick
cable)
738688-211
Keyboard with pointing stick for 14-in models for use in Hungary (includes keyboard cable and pointing
stick cable)
738688-251
Keyboard with pointing stick for 14-in models for use in Russia (includes keyboard cable and pointing
stick cable)
738688-261
Keyboard with pointing stick for 14-in models for use in Bulgaria (includes keyboard cable and pointing
stick cable)
738688-271
Keyboard with pointing stick for 14-in models for use in Romania (includes keyboard cable and pointing
stick cable)
738688-281
Keyboard with pointing stick for 14-in models for use in Thailand (includes keyboard cable and pointing
stick cable)
738688-291
Keyboard with pointing stick for 14-in models for use in Japan (includes keyboard cable and pointing stick
cable)
738688-A41
Keyboard with pointing stick for 14-in models for use in Belgium includes keyboard cable and pointing
stick cable)
738688-AB1
Keyboard with pointing stick for 14-in models for use in Taiwan (includes keyboard cable and pointing
stick cable)
738688-AD1
Keyboard with pointing stick for 14-in models for use in South Korea includes keyboard cable and
pointing stick cable)
738688-B31
Keyboard with pointing stick for 14-in models for use in the Netherlands (includes keyboard cable and
pointing stick cable)
738688-B71
Keyboard with pointing stick for 14-in models for use in Sweden and Finland (includes keyboard cable
and pointing stick cable)
738688-BA1
Keyboard with pointing stick for 14-in models for use in Slovenia (includes keyboard cable and pointing
stick cable)
738688-BB1
Keyboard with pointing stick for 14-in models for use in Israel includes keyboard cable and pointing stick
cable)
738688-BG1
Keyboard with pointing stick for 14-in models for use in Switzerland (includes keyboard cable and
pointing stick cable)
738688-D61
Keyboard with pointing stick for 14-in models for use in India (includes keyboard cable and pointing stick
cable)
738688-DB1
Keyboard with pointing stick for 14-in models for use in Canada (includes keyboard cable and pointing
stick cable)
738688-DD1
Keyboard with pointing stick for 14-in models for use in Iceland includes keyboard cable and pointing
stick cable)
Chapter 3 Illustrated parts catalog
Spare part number
Description
738688-FL1
Keyboard with pointing stick for 14-in models for use in the Czech Republic and Serbia (includes keyboard
cable and pointing stick cable)
738688-FP1
Keyboard with pointing stick for 14-in models for use in Northwest Africa (includes keyboard cable and
pointing stick cable)
738689-001
Screw Kit
738690-001
Display bezel for 15.6-in models
738691-001
Raw Panel Support Kit for 15.6-in models (includes wireless antennas and transceivers)
738692-001
Base enclosure for 15.6-in models
738693-001
Service cover for use on computer models equipped with a 15.6–inch display assembly
738694-001
Power connector cable for use on models equipped with a 15.6–inch display assembly
738695-001
Display cable kit for use on models equipped with a 15.6–inch display assembly (includes display panel
cable)
738696-001
Keyboard for 15.6-in models for use in the United States (includes keyboard cable)
738696-031
Keyboard for 15.6-in models for use in the United Kingdom and Singapore (includes keyboard cable)
738696-041
Keyboard for 15.6-in models for use in Germany (includes keyboard cable)
738696-051
Keyboard for 15.6-in models for use in France (includes keyboard cable)
738696-061
Keyboard for 15.6-in models for use in Italy (includes keyboard cable)
738696-071
Keyboard for 15.6-in models for use in Spain (includes keyboard cable)
738696-081
Keyboard for 15.6-in models for use in Denmark (includes keyboard cable)
738696-091
Keyboard for 15.6-in models for use in Norway (includes keyboard cable and pointing stick cable)
738696-131
Keyboard for 15.6-in models for use in Portugal (includes keyboard cable)
738696-141
Keyboard for 15.6-in models for use in Turkey (includes keyboard cable)
738696-151
Keyboard for 15.6-in models for use in Greece (includes keyboard cable and pointing stick cable)
738696-161
Keyboard for 15.6-in models for use in Latin America (includes keyboard cable)
738696-171
Keyboard for 15.6-in models for use in Saudi Arabia (includes keyboard cable)
738696-201
Keyboard for 15.6-in models for use in Brazil (includes keyboard cable)
738696-211
Keyboard for 15.6-in models for use in Hungary (includes keyboard cable and pointing stick cable)
738696-251
Keyboard for 15.6-in models for use in Russia (includes keyboard cable)
738696-261
Keyboard for 15.6-in models for use in Bulgaria (includes keyboard cable)
738696-271
Keyboard for 15.6-in models for use in Romania (includes keyboard cable)
738696-281
Keyboard for 15.6-in models for use in Thailand (includes keyboard cable)
738696-291
Keyboard for 15.6-in models for use in Japan (includes keyboard cable and pointing stick cable)
738696-A41
Keyboard for 15.6-in models for use in Belgium (includes keyboard cable)
738696-AB1
Keyboard for 15.6-in models for use in Taiwan (includes keyboard cable)
738696-AD1
Keyboard for 15.6-in models for use in South Korea (includes keyboard cable)
Sequential part number listing
49
50
Spare part number
Description
738696-B31
Keyboard for 15.6-in models for use in the Netherlands (includes keyboard cable)
738696-B71
Keyboard for 15.6-in models for use in Sweden and Finland (includes keyboard cable and pointing
stick cable)
738696-BA1
Keyboard for 15.6-in models for use in Slovenia (includes keyboard cable)
738696-BB1
Keyboard for 15.6-in models for use in Israel (includes keyboard cable)
738696-BG1
Keyboard for 15.6-in models for use in Switzerland (includes keyboard cable)
738696-D61
Keyboard for 15.6-in models for use in India (includes keyboard cable)
738696-DB1
Keyboard for 15.6-in models for use in Canada (includes keyboard cable)
738696-DD1
Keyboard for 15.6-in models for use in Iceland (includes keyboard cable)
738696-FL1
Keyboard for 15.6-in models for use in the Czech Republic and Slovakia (includes keyboard cable)
738696-FP1
Keyboard for 15.6-in models for use in Northwest Africa (includes keyboard cable)
738697-001
Keyboard with pointing stick for 15.6-in models for use in the United States (includes keyboard cable and
pointing stick cable)
738697-031
Keyboard with pointing stick for 15.6-in models for use in the United Kingdom and Singapore (includes
keyboard cable and pointing stick cable)
738697-041
Keyboard with pointing stick for 15.6-in models for use in Germany (includes keyboard cable and pointing
stick cable)
738697-051
Keyboard with pointing stick for 15.6-in models for use in France (includes keyboard cable and pointing
stick cable)
738697-061
Keyboard with pointing stick for 15.6-in models for use in Italy (includes keyboard cable and pointing
stick cable)
738697-071
Keyboard with pointing stick for 15.6-in models for use in Spain (includes keyboard cable and pointing
stick cable)
738697-081
Keyboard with pointing stick for 15.6-in models for use in Denmark (includes keyboard cable and pointing
stick cable)
738697-091
Keyboard with pointing stick for 15.6-in models for use in Norway (includes keyboard cable and pointing
stick cable)
738697-131
Keyboard with pointing stick for 15.6-in models for use in Portugal (includes keyboard cable and pointing
stick cable)
738697-141
Keyboard with pointing stick for 15.6-in models for use in Turkey (includes keyboard cable and pointing
stick cable)
738697-151
Keyboard with pointing stick for 15.6-in models for use in Greece (includes keyboard cable and pointing
stick cable)
738697-161
Keyboard with pointing stick for 15.6-in models for use in Latin America (includes keyboard cable and
pointing stick cable)
738697-171
Keyboard with pointing stick for 15.6-in models for use in Saudi Arabia (includes keyboard cable and
pointing stick cable)
738697-211
Keyboard with pointing stick for 15.6-in models for use in Hungary (includes keyboard cable and pointing
stick cable)
738697-251
Keyboard with pointing stick for 15.6-in models for use in Russia (includes keyboard cable and pointing
stick cable)
Chapter 3 Illustrated parts catalog
Spare part number
Description
738697-261
Keyboard with pointing stick for 15.6-in models for use in Bulgaria (includes keyboard cable and pointing
stick cable)
738697-271
Keyboard with pointing stick for 15.6-in models for use in Romania (includes keyboard cable and pointing
stick cable)
738697-281
Keyboard with pointing stick for 15.6-in models for use in Thailand (includes keyboard cable and pointing
stick cable)
738697-291
Keyboard with pointing stick for 15.6-in models for use in Japan (includes keyboard cable and pointing
stick cable)
738697-A41
Keyboard with pointing stick for 15.6-in models for use in Belgium (includes keyboard cable and pointing
stick cable)
738697-AB1
Keyboard with pointing stick for 15.6-in models for use in Taiwan (includes keyboard cable and pointing
stick cable)
738697-AD1
Keyboard with pointing stick for 15.6-in models for use in South Korea (includes keyboard cable and
pointing stick cable)
738697-B31
Keyboard with pointing stick for 15.6-in models for use in the Netherlands (includes keyboard cable and
pointing stick cable)
738697-B71
Keyboard with pointing stick for 15.6-in models for use in Sweden and Finland (includes keyboard cable
and pointing stick cable)
738697-BA1
Keyboard with pointing stick for 15.6-in models for use in Slovenia (includes keyboard cable and pointing
stick cable)
738697-BB1
Keyboard with pointing stick for 15.6-in models for use in Israel (includes keyboard cable and pointing
stick cable)
738697-BG1
Keyboard with pointing stick for 15.6-in models for use in Switzerland (includes keyboard cable and
pointing stick cable)
738697-DB1
Keyboard with pointing stick for 15.6-in models for use in Canada (includes keyboard cable and pointing
stick cable)
738697-DD1
Keyboard with pointing stick for 15.6-in models for use in Iceland (includes keyboard cable and pointing
stick cable)
738697-FL1
Keyboard with pointing stick for 15.6-in models for use in the Czech Republic and Slovakia (includes
keyboard cable and pointing stick cable)
738697-FP1
Keyboard with pointing stick for 15.6-in models for use in Northwest Africa (includes keyboard cable and
pointing stick cable)
738699-001
Display hinge Kit for 15.6-in models (includes left and right hinges and display panel cable bracket)
738701-001
Power button board for 15.6-in models (includes cable)
738702-001
USB board for use in 15.6-in ProBook 650 G1 models (includes cable)
738703-001
Function button board for 15.6-in models (includes cable)
738704-001
Optical drive transfer board for 15.6-in models (includes cable)
738705-001
Modem transfer board for select 15.6-in models (includes cable)
738706-001
Plastics Kit
738708-001
Top cover and 2-button TouchPad for HP ProBook 650 G1 models
738709-001
Top cover and 4-button TouchPad for HP ProBook 650 G1 models
Sequential part number listing
51
52
Spare part number
Description
738710-001
TouchPad for 15.6-in models with 2 buttons (includes bracket)
738711-001
TouchPad for 15.6-in models with 4 buttons (includes bracket)
738712-001
Display bezel for 14-in models
739997-001
Display panel for 15.6-in models, HD SVA AG flat
739998-001
Display panel for 15.6-in models, FHD SVA AG slim
739999-001
DVD±RW Double-Layer Combo Drive
740000-001
DVD-ROM Drive
740001-001
DVD-ROM SuperMulti Drive
744005-001
Smart card reader for 14-in models with 4-button TouchPad (includes cable)
744007-001
System board for use only on computer models equipped with shared memory, WWAN capability
(includes replacement thermal material)
744007-501
System board for use only on computer models equipped with shared memory, WWAN capability, and the
Windows 8 Standard operating system (includes replacement thermal material)
744007-601
System board for use only on computer models equipped with shared memory, WWAN capability, and the
Windows 8 Professional operating system (includes and replacement thermal material)
744008-001
System board for use only on computer models equipped with discrete memory, WWAN capability
(includes replacement thermal material)
744008-501
System board for use only on computer models equipped with discrete memory, WWAN capability, and
the Windows 8 Standard operating system (includes replacement thermal material)
744008-601
System board for use only on computer models equipped with discrete memory, WWAN capability, and
the Windows 8 Professional operating system (includes and replacement thermal material)
744009-001
System board for use only on computer models equipped with shared memory, WWAN capability
(includes replacement thermal material)
744009-501
System board for use only on computer models equipped with shared memory, WWAN capability, and the
Windows 8 Standard operating system (includes replacement thermal material)
744009-601
System board for use only on computer models equipped with shared memory, WWAN capability, and the
Windows 8 Professional operating system (includes and replacement thermal material)
744010-001
System board for use only on computer models equipped with discrete memory, WWAN capability
(includes replacement thermal material)
744010-501
System board for use only on computer models equipped with discrete memory, WWAN capability, and
the Windows 8 Standard operating system (includes replacement thermal material)
744010-601
System board for use only on computer models equipped with discrete memory, WWAN capability, and
the Windows 8 Professional operating system (includes and replacement thermal material)
744013-001
Cable Kit for HP ProBook 650 G1 models with a 15.6–inch display assembly (includes power connector
cable and RJ-45 (network) cable and replacement thermal material)
744015-001
System board for use only on computer models equipped with shared memory, WWAN capability
(includes replacement thermal material)
744015-501
System board for use only on computer models equipped with shared memory, WWAN capability, and the
Windows 8 Standard operating system (includes replacement thermal material)
744015-601
System board for use only on computer models equipped with shared memory, WWAN capability, and the
Windows 8 Professional operating system (includes and replacement thermal material)
Chapter 3 Illustrated parts catalog
Spare part number
Description
744016-001
System board for use only on computer models equipped with shared memory, WWAN capability, a
modem (includes replacement thermal material)
744016-501
System board for use only on computer models equipped with shared memory, WWAN capability, a
modem, and the Windows 8 Standard operating system (includes replacement thermal material)
744016-601
System board for use only on computer models equipped with shared memory, WWAN capability, a
modem, and the Windows 8 Professional operating system (includes and replacement thermal material)
744017-001
System board for use only on computer models equipped with discrete memory, WWAN capability
(includes replacement thermal material)
744017-501
System board for use only on computer models equipped with discrete memory, WWAN capability, and
the Windows 8 Standard operating system (includes replacement thermal material)
744017-601
System board for use only on computer models equipped with discrete memory, WWAN capability, and
the Windows 8 Professional operating system (includes and replacement thermal material)
744018-001
System board for use only on computer models equipped with discrete memory, a modem, WWAN
capability (includes replacement thermal material)
744018-501
System board for use only on computer models equipped with discrete memory, WWAN capability, a
modem, and the Windows 8 Standard operating system (includes replacement thermal material)
744018-601
System board for use only on computer models equipped with shared memory, WWAN capability, a
modem, and the Windows 8 Professional operating system (includes and replacement thermal material)
744019-001
System board for use only on computer models equipped with shared memory, WWAN capability
(includes replacement thermal material)
744019-501
System board for use only on computer models equipped with shared memory, WWAN capability, and the
Windows 8 Standard operating system (includes replacement thermal material)
744019-601
System board for use only on computer models equipped with shared memory, WWAN capability, and the
Windows 8 Professional operating system (includes and replacement thermal material)
744020-001
System board for use only on computer models equipped with shared memory, WWAN capability, a
modem (includes replacement thermal material)
744020-501
System board for use only on computer models equipped with shared memory, WWAN capability, a
modem, and the Windows 8 Standard operating system (includes replacement thermal material)
744020-601
System board for use only on computer models equipped with shared memory, WWAN capability, a
modem, and the Windows 8 Professional operating system (includes and replacement thermal material)
744021-001
System board for use only on computer models equipped with discrete memory, WWAN capability
(includes replacement thermal material)
744021-501
System board for use only on computer models equipped with discrete memory, WWAN capability, and
the Windows 8 Standard operating system (includes replacement thermal material)
744021-601
System board for use only on computer models equipped with discrete memory, WWAN capability, and
the Windows 8 Professional operating system (includes and replacement thermal material)
744022-001
System board for use only on computer models equipped with discrete memory, a modem, WWAN
capability (includes replacement thermal material)
744022-501
System board for use only on computer models equipped with discrete memory, WWAN capability, a
modem, and the Windows 8 Standard operating system (includes replacement thermal material)
744022-601
System board for use only on computer models equipped with shared memory, WWAN capability, a
modem, and the Windows 8 Professional operating system (includes and replacement thermal material)
744715-001
System board for use only on computer models equipped with shared memory, without WWAN capability
(includes replacement thermal material)
Sequential part number listing
53
54
Spare part number
Description
744715-501
System board for use only on computer models equipped with shared memory, without WWAN capability,
and the Windows 8 Standard operating system (includes replacement thermal material)
744715-601
System board for use only on computer models equipped with shared memory, without WWAN capability,
and the Windows 8 Professional operating system (includes and replacement thermal material)
744820-001
Blu-ray ROM DVD±RW Combo Drive
744821-001
DVD-ROM 9.5-mm Drive
744822-001
DVD-ROM SuperMulti 9.5-mm Drive
745883-001
For use only computer models with shared memory and WWAN capability
745883-501
For use only on computer models with shared memory, the Windows 8 Standard operating system, and
WWAN capability
745883-601
For use only on computer models with shared memory, the Windows 8 Professional operating system,
and WWAN capability
745884-001
For use only computer models equipped with shared memory without WWAN capability
745884-501
For use only on computer models equipped with shared memory and the Windows 8 Standard operating
system without WWAN capability
745884-601
For use only on computer models equipped with shared memory, the Windows 8 Professional operating
system without WWAN capability
745887-001
System board for use only on 15.6-in models with shared memory, WWAN capability (includes
replacement thermal material)
745887-501
System board for use only on 15.6-in models with shared memory, WWAN capability, and the Windows 8
Standard operating system (includes replacement thermal material)
745887-601
System board for use only on 15.6-in models with shared memory, WWAN capability, and the Windows 8
Professional operating system (includes and replacement thermal material)
745888-001
System board for use only on 15.6-in models with shared memory, without WWAN capability (includes
replacement thermal material)
745888-501
System board for use only on 15.6-in models with shared memory, without WWAN capability, and the
Windows 8 Standard operating system (includes replacement thermal material)
745888-601
System board for use only on 15.6-in models with shared memory, without WWAN capability, and the
Windows 8 Professional operating system (includes and replacement thermal material)
745889-001
Top cover and 2-button TouchPad for HP ProBook 655 G1 models
745890-001
Top cover and 4-button TouchPad for HP ProBook 655 G1 models
745891-001
USB board for use in ProBook 655 G1 models (includes cable)
745892-001
Cable Kit for HP ProBook 650 G1 models with a 15.6–inch display assembly (includes power connector
cable and RJ-45 (network) cable and replacement thermal material)
745893-001
Display bezel
747751-001
Display panel for 14-in models, HD AG WLED SVA eDP FLT
747752-001
Display panel for 14-in models, HD+ AG WLED SVA eDP FLT
747753-001
Display panel for 14-in models, FHD AG WLED UWVA eDPslim PSR
747832-001
Intel 802.11 a/b/g/n 2x2 + BT 4.0 WLAN
748357-001
Service cover for use on computer models equipped with a 14-inch display assembly and which meet
regional configure to order (RCTO) specifications
Chapter 3 Illustrated parts catalog
Spare part number
Description
748358-001
Service cover for use on computer models equipped with a 15.6-inch display assembly and which meet
regional configure to order (RCTO) specifications
748958-001
Smart card reader board with TouchPad, for use on 15.6–inch models
749254-001
System board for use only on computer models equipped with shared memory and a modem (includes
replacement thermal material)
749261-001
128-GB SATA-3 solid-state drive
749262-001
180-GB SATA-3 solid-state drive
749263-001
256-GB SATA-3 self-encrypting solid-state drive
749274-001
System board for use only on computer models equipped with shared memory (includes replacement
thermal material)
749274-501
System board for use only on computer models equipped with shared memory and the Windows 8
Standard operating system (includes replacement thermal material)
749274-601
System board for use only on computer models equipped with shared memory and the Windows 8
Professional operating system (includes and replacement thermal material)
749277-001
128-GB mSATA-3 solid-state drive
749278-001
128-GB SATA-3 solid-state drive
749279-001
180-GB SATA-3 solid-state drive
749280-001
128-GB mSATA-3 solid-state drive for use in Brazil
749281-001
32-GB mSATA flash cache solid-state drive
749263-001
256-GB SATA-3 self-encrypting solid-state drive
749263-001
256-GB SATA-3 self-encrypting solid-state drive
749284-001
128-GB mSATA-3 solid-state drive
749285-001
128-GB mSATA-3 solid-state drive for use in Brazil
749286-001
180-GB mSATA-3 solid-state drive
749287-001
256-GB mSATA-3 solid-state self-encrypting drive
749609-001
Display panel HD SVA AG flat
749610-001
Display panel HD SVA AG flat
749954-001
128-GB SATA-3 solid-state drive
749955-001
180-GB SATA-3 solid-state drive
749956-001
256-GB SATA-3 self-encrypting solid-state drive
749957-001
DVD-ROM 9.5-mm Drive
749958-001
DVD-ROM SuperMulti 9.5-mm Drive
749959-001
Blu-ray R/RE DVD±RW SuperMulti Double-Layer Combo Drive
787294-001
Keyboard for 14-inch models for use in the United States (includes keyboard and backlight cables)
787294-031
Keyboard for 14-inch models for use in the United Kingdom and Singapore (includes keyboard and
backlight cables)
787294-041
Keyboard for 14-inch models for use in Germany (includes keyboard and backlight cables)
Sequential part number listing
55
56
Spare part number
Description
787294-051
Keyboard for 14-inch models for use in France (includes keyboard and backlight cables)
787294-061
Keyboard for 14-inch models for use in Italy (includes keyboard and backlight cables)
787294-071
Keyboard for 14-inch models for use in Spain (includes keyboard and backlight cables)
787294-081
Keyboard for 14-inch models for use in Denmark (includes keyboard and backlight cables)
787294-091
Keyboard for 14-inch models for use in Norway (includes keyboard and backlight cables)
787294-131
Keyboard for 14-inch models for use in Portugal (includes keyboard and backlight cables)
787294-141
Keyboard for 14-inch models for use in Turkey (includes keyboard and backlight cables)
787294-151
Keyboard for 14-inch models for use in Greece (includes keyboard and backlight cables)
787294-161
Keyboard for 14-inch models for use in Latin America (includes keyboard and backlight cables)
787294-171
Keyboard for 14-inch models for use in Saudi Arabia (includes keyboard and backlight cables)
787294-201
Keyboard for 14-inch models for use in Brazil (includes keyboard and backlight cables)
787294-211
Keyboard for 14-inch models for use in Hungary (includes keyboard and backlight cables)
787294-251
Keyboard for 14-inch models for use in Russia (includes keyboard and backlight cables)
787294-261
Keyboard for 14-inch models for use in Bulgaria (includes keyboard and backlight cables)
787294-271
Keyboard for 14-inch models for use in Romania (includes keyboard and backlight cables)
787294-281
Keyboard for 14-inch models for use in Thailand (includes keyboard and backlight cables)
787294-291
Keyboard for 14-inch models for use in Japan (includes keyboard and backlight cables)
787294-A41
Keyboard for 14-inch models for use in Belgium (includes keyboard and backlight cables)
787294-AB1
Keyboard for 14-inch models for use in Taiwan (includes keyboard and backlight cables)
787294-AD1
Keyboard for 14-inch models for use in South Korea (includes keyboard and backlight cables)
787294-B31
Keyboard for 14-inch models for use in the Netherlands (includes keyboard and backlight cables)
787294-B71
Keyboard for 14-inch models for use in Sweden and Finland (includes keyboard and backlight cables)
787294-BA1
Keyboard for 14-inch models for use in Slovenia (includes keyboard and backlight cables)
787294-BB1
Keyboard for 14-inch models for use in Israel (includes keyboard and backlight cables)
787294-BG1
Keyboard for 14-inch models for use in Switzerland (includes keyboard and backlight cables)
787294-D61
Keyboard for 14-inch models for use in India (includes keyboard and backlight cables)
787294-DB1
Keyboard for 14-inch models for use in Canada (includes keyboard and backlight cables)
787294-DD1
Keyboard for 14-inch models for use in Iceland (includes keyboard and backlight cables)
787294-FL1
Keyboard for 14-inch models for use in Czech Republic and Slovakia (includes keyboard and backlight
cables)
787294-FP1
Keyboard for 14-inch models for use in Northwest Africa (includes keyboard and backlight cables)
787801-001
Keyboard for 15.6-inch models for use in the United States (includes keyboard and backlight cables)
787801-031
Keyboard for 15.6-inch models for use in the United Kingdom and Singapore (includes keyboard and
backlight cables)
787801-041
Keyboard for 15.6-inch models for use in Germany (includes keyboard and backlight cables)
Chapter 3 Illustrated parts catalog
Spare part number
Description
787801-051
Keyboard for 15.6-inch models for use in France (includes keyboard and backlight cables)
787801-061
Keyboard for 15.6-inch models for use in Italy (includes keyboard and backlight cables)
787801-071
Keyboard for 15.6-inch models for use in Spain (includes keyboard and backlight cables)
787801-081
Keyboard for 15.6-inch models for use in Denmark (includes keyboard and backlight cables)
787801-091
Keyboard for 15.6-inch models for use in Norway (includes keyboard and backlight cables)
787801-131
Keyboard for 15.6-inch models for use in Portugal (includes keyboard and backlight cables)
787801-141
Keyboard for 15.6-inch models for use in Turkey (includes keyboard and backlight cables)
787801-151
Keyboard for 15.6-inch models for use in Greece (includes keyboard and backlight cables)
787801-161
Keyboard for 15.6-inch models for use in Latin America (includes keyboard and backlight cables)
787801-171
Keyboard for 15.6-inch models for use in Saudi Arabia (includes keyboard and backlight cables)
787801-201
Keyboard for 15.6-inch models for use in Brazil (includes keyboard and backlight cables)
787801-211
Keyboard for 15.6-inch models for use in Hungary (includes keyboard and backlight cables)
787801-251
Keyboard for 15.6-inch models for use in Russia (includes keyboard and backlight cables)
787801-261
Keyboard for 15.6-inch models for use in Bulgaria (includes keyboard and backlight cables)
787801-271
Keyboard for 15.6-inch models for use in Romania (includes keyboard and backlight cables)
787801-281
Keyboard for 15.6-inch models for use in Thailand (includes keyboard and backlight cables)
787801-291
Keyboard for 15.6-inch models for use in Japan (includes keyboard and backlight cables)
787801-A41
Keyboard for 15.6-inch models for use in Belgium (includes keyboard and backlight cables)
787801-AB1
Keyboard for 15.6-inch models for use in Taiwan (includes keyboard and backlight cables)
787801-AD1
Keyboard for 15.6-inch models for use in South Korea (includes keyboard and backlight cables)
787801-B31
Keyboard for 15.6-inch models for use in the Netherlands (includes keyboard and backlight cables)
787801-B71
Keyboard for 15.6-inch models for use in Sweden and Finland (includes keyboard and backlight cables)
787801-BA1
Keyboard for 15.6-inch models for use in Slovenia (includes keyboard and backlight cables)
787801-BB1
Keyboard for 15.6-inch models for use in Israel (includes keyboard and backlight cables)
787801-BG1
Keyboard for 15.6-inch models for use in Switzerland (includes keyboard and backlight cables)
787801-D61
Keyboard for 15.6-inch models for use in India (includes keyboard and backlight cables)
787801-DB1
Keyboard for 15.6-inch models for use in Canada (includes keyboard and backlight cables)
787801-DD1
Keyboard for 15.6-inch models for use in Iceland (includes keyboard and backlight cables)
787801-FL1
Keyboard for 15.6-inch models for use in Czech Republic and Slovakia (includes keyboard and backlight
cables)
787801-FP1
Keyboard for 15.6-inch models for use in Northwest Africa (includes keyboard and backlight cables)
805782-001
Top cover for ProBook 655 G1 models equipped with a backlit keyboard
805783-001
Top cover and 2-button TouchPad for models equipped with a 14–inch display assembly and a backlit
keyboard
805787-001
Top cover for ProBook 650 G1 models equipped with a backlit keyboard
Sequential part number listing
57
4
Removal and replacement procedures
preliminary requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
Flat-bladed screw driver
●
Magnetic screw driver
●
Phillips P0 and P1 screw drivers
Service considerations
The following sections include some of the considerations that you must keep in mind during disassembly
and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all accompanying
screws) away from the work area to prevent damage.
Plastic parts
CAUTION: Using excessive force during disassembly and reassembly can damage plastic parts. Use care
when handling the plastic parts. Apply pressure only at the points designated in the
maintenance instructions.
58
Chapter 4 Removal and replacement procedures preliminary requirements
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the
reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or
seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases,
avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that they cannot be
caught or snagged by parts being removed or replaced. Handle flex cables with extreme care; these cables
tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to
the computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the computer
is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive, avoid
touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and be sure
that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing an internal hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a normal
cycle. Or the device may function normally for a while, and then degrade in the internal layers, reducing its
life expectancy.
Grounding guidelines
59
CAUTION: To prevent damage to the computer when you are removing or installing internal components,
observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Before touching an electronic component, discharge static electricity by using the guidelines described in this
section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by
different activities.
CAUTION: A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
60
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Chapter 4 Removal and replacement procedures preliminary requirements
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●
Place items on a grounded surface before removing items from their containers.
●
Always be properly grounded when touching a component or assembly.
●
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that mechanized
equipment used for moving materials is wired to ground and that proper materials are selected to avoid
static charging. When grounding is not possible, use an ionizer to dissipate electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
●
Cover the workstation with approved static-shielding material.
●
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and
equipment.
●
Use conductive field service tools, such as cutters, screw drivers, and vacuums.
●
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids
and Styrofoam.
●
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle these
items only at static-free workstations.
●
Avoid contact with pins, leads, or circuitry.
●
Turn off power and input signals before inserting or removing connectors or test equipment.
Grounding guidelines
61
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a
minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap
snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips
to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps) can be
used at standing workstations and are compatible with most types of shoes or boots. On conductive
floors or dissipative floor mats, use foot straps on both feet with a minimum of one megohm resistance
between the operator and ground. To be effective, the conductive must be worn in contact with the
skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
Antistatic tape
●
Antistatic smocks, aprons, and sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Nonconductive foam
●
Conductive tabletop workstations with ground cords of one megohm resistance
●
Static-dissipative tables or floor mats with hard ties to the ground
●
Field service kits
●
Static awareness labels
●
Material-handling packages
●
Nonconductive plastic bags, tubes, or boxes
●
Metal tote boxes
●
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
62
Material
Use
Voltage protection level
Antistatic plastics
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Chapter 4 Removal and replacement procedures preliminary requirements
5
Removal and replacement procedures for
Customer Self-Repair parts
NOTE: The Customer Self-Repair program is not available in all locations. Installing a part not supported by
the Customer Self-Repair program may void your warranty. Check your warranty to determine if Customer
Self-Repair is supported in your location.
Component replacement procedures
NOTE: Please read and follow the procedures described here to access and replace Customer Self-Repair
parts successfully.
NOTE: Details about your computer, including model, serial number, product key, and length of warranty,
are on the service tag at the bottom of your computer. See Service tag on page 16 for details.
This chapter provides removal and replacement procedures for Customer Self-Repair parts.
There are as many as 16 screws that must be removed, replaced, and/or loosened when servicing Customer
Self-Repair parts. Make special note of each screw size and location during removal and replacement.
Component replacement procedures
63
Battery
Description
Spare part number
9-cell, 100-WHr, 3.0-AHr, Li-ion battery
718757-001
9-cell, 73-WHr, 2.2-AHr, Li-ion battery
718756-001
8-cell, 83-WHr, 2.8-AHr, Li-ion battery
718755-001
8-cell, 75-WHr, 2.8-AHr, Li-ion battery
718754-001
Before removing the battery, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
Remove the battery:
WARNING! To reduce potential safety issues, use only the user-replaceable battery provided with the
computer, a replacement battery provided by HP, or a compatible battery purchased from HP.
CAUTION: Removing a user-replaceable battery that is the sole power source for the computer can cause
loss of information. To prevent loss of information, save your work or shut down the computer through
Windows before removing the battery.
1.
Turn the computer upside down on a flat surface.
2.
Slide the battery release latch (1) to release the battery.
NOTE:
3.
The battery release latch automatically returns to its original position.
Remove the battery (2) from the computer.
Reverse this procedure to install the battery.
64
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
Service cover
Description
Spare part number
Service cover for use on computer models equipped with a 15.6-inch display assembly
738693-001
Service cover for use on computer models equipped with a 15.6-inch display assembly and which meet
regional configure to order (RCTO) specifications
748358-001
Service cover for use on computer models equipped with a 14-inch display assembly
738682-001
Service cover for use on computer models equipped with a 14-inch display assembly and which meet
regional configure to order (RCTO) specifications
748357-001
Remove the service cover to access the memory module slot, hard drive, and other components.
1.
Remove the battery (see Battery on page 64).
2.
With the battery bay toward you, slide the service cover release latch (1) to the left, remove the screw
(if the optional screw is being used) (2), and then slide the release latch again (3) to release the service
cover.
NOTE:
3.
If you not want to use the optional screw, you can store it inside the service cover.
Slide the service cover toward the front of the computer (4) and lift (5) to remove the service cover.
Reverse this procedure to install the service cover.
Component replacement procedures
65
Hard drive
NOTE: The hard drive spare part kit does not include the hard drive bracket or screws. These components
are included in the Hard Drive Hardware Kit, spare part number 738395-001.
Description
Spare part number
Hard drive (does not include hard drive bracket or screws):
1-TB, 5400-rpm, 9.5-mm
676521-001
750-GB, 7200-rpm, 9.5-mm
633252-001
500-GB, 7200-rpm, 7.0-mm
703267-001
500-GB, 7200-rpm, 7.0-mm
634925-001
500-GB, 7200-rpm, 7.0-mm, self-encrypting
703268-001
500-GB, 5400-rpm, 7.0-mm, FIPS
730946-001
500-GB, 5400-rpm, 9.5-mm, self-encrypting
683801-001
500-GB, 5400-rpm, 7.0-mm
683802-001
320-GB, 7200-rpm, 9.5-mm
603783-001
320-GB, 7200-rpm, 7.0-mm
634862-001
320-GB, 5400-rpm, 7.0-mm
670035-001
Before removing the hard drive, follow these steps:
1.
Save your work and shut down the computer.
2.
Disconnect AC power and external devices connected to the computer.
3.
Turn the computer upside down on a flat surface.
4.
Remove the battery. (See Battery on page 64).
Remove the hard drive:
1.
66
Disconnect the hard drive cable(1).
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
2.
Loosen the 4 hard drive screws (2). Pull the hard drive tab (3) to the right to disconnect the hard drive.
3.
Lift the hard drive (4), and then pull the hard drive out of the hard drive bay.
4.
If it is necessary to disassemble the hard drive, perform the following steps:
a.
Position the hard drive with the hard drive tab toward you.
b.
Remove the four Phillips screws (1) that secure the hard drive bracket to the hard drive.
Component replacement procedures
67
c.
Remove the hard drive bracket (2) from the hard drive.
The hard drive bracket and screws are available in the Hard Drive Hardware Kit, spare part number
738395-001.
Reverse this procedure to install a hard drive.
Modem module (select models only)
Description
Spare part number
Modem module
628824-001
Before removing the modem module, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64).
5.
Remove the service cover (see Service cover on page 65).
Remove the modem module:
1.
68
Remove the two Phillips screws (1) that secure the modem module.
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
2.
Lift the front of the modem module (2), and then disconnect the modem cable (3).
3.
Release the modem module connector board from the clip, and then release the ZIF connector to
remove modem module connector board.
Reverse this procedure to install a modem module.
Primary memory module
The computer has one memory module compartment. The capacity of the computer can be upgraded by
adding a memory module to the vacant expansion memory module slot or by upgrading the existing memory
module in the primary memory module slot.
WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord and
remove all batteries before installing a memory module.
CAUTION: Electrostatic discharge (ESD) can damage electronic components. Before beginning any
procedure, ensure that you are discharged of static electricity by touching a grounded metal object.
CAUTION: To prevent information loss or an unresponsive system:
Shut down the computer before adding or replacing memory modules. Do not remove a memory module
while the computer is on, in the Sleep state, or in Hibernation.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power
button. Then shut down the computer through the operating system.
NOTE: To use a dual-channel configuration when adding a second memory module, be sure that both
memory modules are identical.
NOTE: The primary memory is located in the bottom memory slot and the expansion memory is located in
the top memory slot.
Description
Spare part number
8-GB (PC3L, 12800, 1600-MHz)
693374-001
Component replacement procedures
69
Description
Spare part number
4-GB (PC3L, 12800, 1600-MHz)
691740-001
2-GB (PC3L, 12800, 1600-MHz)
691739-001
To add or replace a memory module:
1.
Save your work and shut down the computer.
2.
Disconnect AC power and external devices connected to the computer.
3.
Remove the battery (see Battery on page 64).
4.
Remove the service cover (see Service cover on page 65).
5.
If you are replacing a memory module, remove the existing memory module:
a.
Pull away the retention clips (1) on each side of the memory module.
The memory module tilts up.
b.
Grasp the edge of the memory module (2), and then gently pull the memory module out of the
memory module slot.
CAUTION: To prevent damage to the memory module, hold the memory module by the edges
only. Do not touch the components on the memory module.
To protect a memory module after removal, place it in an electrostatic-safe container.
6.
Insert a new memory module:
CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do
not touch the components on the memory module.
70
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
a.
Align the notched edge (1) of the memory module with the tab in the memory module slot.
b.
With the memory module at a 45-degree angle from the surface of the memory module
compartment, press the module (2) into the memory module slot until it is seated.
c.
Gently press the memory module (3) down, applying pressure to both the left and right edges of
the memory module, until the retention clips snap into place.
CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory
module.
Reverse this procedure to install a memory module.
Component replacement procedures
71
Expansion memory module
Update BIOS before adding memory modules
Before adding new memory, make sure you update the computer to the latest BIOS.
CAUTION: Failure to update the computer to the latest BIOS prior to installing new memory may result in
various system problems.
To update BIOS:
1.
Navigate to www.hp.com.
2.
Click Support & Drivers > click Drivers & Software.
3.
In the Enter a product name/number box, type the computer model information, and then click Search.
4.
Click the link for the computer model.
5.
Select the operating system, and then click Next.
6.
Under Step 2: Select a Download, click the BIOS link.
7.
Click the link for the most recent BIOS.
8.
Click the Download button, and then follow the on-screen instructions.
Before removing a memory module, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64).
5.
Remove the service cover (see Service cover on page 65).
Remove the memory module:
1.
72
Spread the retaining tabs (1) on each side of the memory module slot to release the memory module.
(The memory module tilts up.)
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
2.
Remove the memory module (2) by pulling the module away from the slot at an angle.
Reverse this procedure to install a memory module.
Component replacement procedures
73
WWAN module (select models only)
Description
Spare part number
HP hs3110 HSPA+ Mobile Broadband Module
723895-001
HP lt4112 LTE/HSPA+ Mobile Broadband Module
704031-001
HP lt4111 LTE/EV-DO/HSPA+ Mobile Broadband Module
704030-001
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module
authorized for use in the computer by the governmental agency that regulates wireless devices in your
country or region. If you replace the module and then receive a warning message, remove the module to
restore device functionality, and then contact technical support.
Before removing the WWAN module, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64).
5.
Remove the service cover (see Service cover on page 65).
Remove the WWAN module:
1.
Disconnect the WWAN antenna cables (1) from the terminals on the WWAN module.
NOTE: The WWAN antenna cable labeled “5” connects to the WWAN module “Main” terminal labeled
“5”. The WWAN antenna cable labeled “6” connects to the WWAN module “Aux/GPS” terminal labeled
“6”.
2.
74
Remove the Phillips screw (2) that secures the WWAN module to the system board.
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
3.
Remove the WWAN module (3) by pulling the module away from the slot at an angle.
NOTE: If the WWAN antenna cables are not connected to the terminals on the WWAN module, protective
sleeves should be installed on the antenna connectors, as shown in the following illustration.
Reverse this procedure to install the WWAN module.
WLAN module
Description
Spare part number
Intel 802.11 a/b/g/n 2x2 Combo Adapter
670292-001
Intel 802.11 b/g/n HMC 1x1
675794-001
Atheros 802.11 b/g/n 1x1
690019-001
Intel 802.11 2x2 a/b/g/n
695915-001
Intel 802.11 2x2 a/b/g/n
710661-001
Intel 802.11 a/b/g/n 2x2 + Bluetooth 4.0 WLAN
717381-001
Component replacement procedures
75
Description
Spare part number
Broadcom 802.11 a/b/g/n 2x2 + BT 4.0 LE PCIe+USB HMC WW
730668-001
Intel 802.11 a/b/g/n 2x2 + BT 4.0 WLAN
747832-001
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module
authorized for use in the computer by the governmental agency that regulates wireless devices in your
country or region. If you replace the module and then receive a warning message, remove the module to
restore device functionality, and then contact technical support.
Before removing the WLAN module, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64).
5.
Remove the service cover (see Service cover on page 65).
Remove the WLAN module:
1.
Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module.
NOTE: The WLAN antenna cable labeled “1” connects to the WLAN module “Main” terminal labeled
“1”. The WLAN antenna cable labeled “2” connects to the WLAN module “Aux” terminal labeled “2”.
76
2.
Remove the two Phillips screws (2) that secure the WLAN module to the system board.)
3.
Remove the WLAN module (3) by gently pulling the module away from the slot at an angle. (The WLAN
module tilts up.)
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
NOTE: If the WLAN antenna cables are not connected to the terminals on the WLAN module, protective
sleeves should be installed on the antenna connectors, as shown in the following illustration.
Reverse this procedure to install the WLAN module.
Optical drive
NOTE: The optical drive spare part kit includes a bezel and bracket.
Description
Spare part number
Blu-ray R/RE DVD±RW SuperMulti Double-Layer Combo Drive
749959-001
739999-001
744820-001
DVD±RW SuperMulti Double-Layer Drive
749958-001
744822-001
740001-001
DVD-ROM Drive
749957-001
744821-001
740000-001
735601-001
Before removing the optical drive, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64).
5.
Remove the service cover (see Service cover on page 65).
Remove the optical drive:
1.
Position the computer with the left side toward you.
2.
Loosen the captive screw (1) that secures the optical drive to the computer.
Component replacement procedures
77
3.
Insert a thin tool into the optical drive tab access (2), and then press the tab to the left to release the
optical drive from the computer.
4.
Remove the optical drive (3).
Reverse this procedure to install the optical drive.
78
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
Solid-state drive
Description
Spare part number
256-GB SATA-3 self-encrypting SSD
749263-001
180-GB SATA-3 SSD
749262-001
749278-001
128-GB SATA-3 SSD
749261-001
749277-001
128-GB mSATA-3 SSD for use in Brazil
749280-001
32-GB mSATA flash cache SSD
749281-001
Before removing the solid-state drive, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64).
5.
Remove the service cover (see Service cover on page 65).
Remove the solid-state drive:
1.
Remove the two Phillips screws (1) that secure the solid-state drive to the system board. (The solidstate drive tilts up.)
2.
Remove the solid-state drive (2) by pulling the drive away from the slot at an angle.
Reverse this procedure to install the solid-state drive.
Component replacement procedures
79
Keyboard
For use in country or region
Spare part
number
For use in country or region
Spare part number
Keyboard for 15.6–inch models (includes keyboard cable):
For use in Belgium
738696-A41
For use in the Netherlands
738696-B31
For use in Brazil
738696-201
For use in Northwest Africa
738696-FP1
For use in Bulgaria
738696-261
For use in Norway
738696-091
For use in Canada
738696-DB1
For use in Portugal
738696-131
For use in the Czech Republic and Slovakia
738696-FL1
For use in Romania
738696-271
For use in Denmark
738696-051
For use in Russia
738696-251
For use in France
738696-041
For use in Saudi Arabia
738696-171
For use in Germany
738696-151
For use in Slovenia
738696-BA1
For use in Greece
738696-211
For use in Spain
738696-071
For use in Hungary
738696-061
For use in Sweden and Finland
738696-B71
For use in Iceland
738696-DD1
For use in Switzerland
738696-BG1
For use in India
738696-D61
For use in Taiwan
738696-AB1
For use in Israel
738696-BB1
For use in Thailand
738696-281
For use in Italy
738696-061
For use in Turkey
738696-141
For use in Japan
738696-291
For use in the United Kingdom
738696-031
For use in Korea
738696-AD1
For use in the United States
738696-001
For use in Latin America
738696-161
Keyboard for 14–inch models (includes keyboard cable):
80
For use in Belgium
738687-A41
For use in Northwest Africa
738687-FP1
For use in Bulgaria
738687-261
For use in Norway
738687-091
For use in Canada
738687-DB1
For use in Portugal
738687-131
For use in the Czech Republic and Slovakia
738687-FL1
For use in Romania
738687-271
For use in Denmark
738687-081
For use in Russia
738687-251
For use in France
738687-051
For use in Saudi Arabia
738687-171
For use in Germany
738687-041
For use in Slovenia
738687-BA1
For use in Greece
738687-151
For use in South Korea
738687-AD1
For use in Hungary
738687-211
For use in Spain
738687-071
For use in Iceland
738687-DD1
For use in Sweden and Finland
738687-B71
For use in India
738687-D61
For use in Switzerland
738687-BG1
For use in Israel
738687-BB1
For use in Taiwan
738687-AB1
For use in Italy
738687-061
For use in Thailand
738687-281
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
For use in country or region
Spare part
number
For use in country or region
Spare part number
For use in Japan
738687-291
For use in Turkey
738687-141
For use in Latin America
738687-161
For use in the United Kingdom
and Singapore
738687-031
For use in the Netherlands
738687-B31
For use in the United States
738687-001
Keyboard with pointing stick for 15.6–inch models (includes keyboard cable and pointing stick cable):
For use in Belgium
738697-A41
For use in the Netherlands
738697-B31
For use in Brazil
738697-201
For use in Northwest Africa
738697-FP1
For use in Bulgaria
738697-261
For use in Norway
738697-091
For use in Canada
738697-DB1
For use in Portugal
738697-131
For use in the Czech Republic and Slovakia
738697-FL1
For use in Romania
738697-271
For use in Denmark
738697-051
For use in Russia
738697-251
For use in France
738697-041
For use in Saudi Arabia
738697-171
For use in Germany
738697-151
For use in Slovenia
738697-BA1
For use in Greece
738697-211
For use in Spain
738697-071
For use in Hungary
738697-061
For use in Sweden and Finland
738697-B71
For use in Iceland
738697-DD1
For use in Switzerland
738697-BG1
For use in India
738697-D61
For use in Taiwan
738697-AB1
For use in Israel
738697-BB1
For use in Thailand
738697-281
For use in Italy
738697-D61
For use in Turkey
738697-141
For use in Japan
738697-291
For use in the United Kingdom
738697-031
For use in Korea
738697-AD1
For use in the United States
738697-001
For use in Latin America
738697-161
Keyboard with pointing stick for 14–inch models (includes keyboard cable and pointing stick cable):
For use in Belgium
738688-A41
For use in Northwest Africa
738688-FP1
For use in Brazil
738688-201
For use in Norway
738688-091
For use in Bulgaria
738688-261
For use in Portugal
738688-131
For use in Canada
738688-DB1
For use in Romania
738688-271
For use in the Czech Republic and Slovakia
738688-FL1
For use in Russia
738688-251
For use in Denmark
738688-081
For use in Saudi Arabia
738688-171
For use in France
738688-051
For use in Slovenia
738688-BA1
For use in Germany
738688-041
For use in South Korea
738688-AD1
For use in Greece
738688-151
For use in Spain
738688-071
For use in Hungary
738688-211
For use in Sweden and Finland
738688-B71
For use in Iceland
738688-DD1
For use in Switzerland
738688-BG1
Component replacement procedures
81
For use in country or region
Spare part
number
For use in country or region
Spare part number
For use in India
738688-D61
For use in Taiwan
738688-AB1
For use in Israel
738688-BB1
For use in Thailand
738688-281
For use in Italy
738688-061
For use in Turkey
738688-141
For use in Japan
738688-291
For use in the United Kingdom
and Singapore
738688-031
For use in Latin America
738688-161
For use in the United States
738688-001
For use in the Netherlands
738688-B31
Backlit keyboard for 15.6–inch models (includes backlight and keyboard cables):
For use in Belgium
787801-A41
For use in the Netherlands
787801-B31
For use in Brazil
787801-201
For use in Northwest Africa
787801-FP1
For use in Bulgaria
787801-261
For use in Norway
787801-091
For use in Canada
787801-DB1
For use in Portugal
787801-131
For use in the Czech Republic and Slovakia
787801-FL1
For use in Romania
787801-271
For use in Denmark
787801-051
For use in Russia
787801-251
For use in France
787801-041
For use in Saudi Arabia
787801-171
For use in Germany
787801-151
For use in Slovenia
787801-BA1
For use in Greece
787801-211
For use in Spain
787801-071
For use in Hungary
787801-061
For use in Sweden and Finland
787801-B71
For use in Iceland
787801-DD1
For use in Switzerland
787801-BG1
For use in India
787801-D61
For use in Taiwan
787801-AB1
For use in Israel
787801-BB1
For use in Thailand
787801-281
For use in Italy
787801-061
For use in Turkey
787801-141
For use in Japan
787801-291
For use in the United Kingdom
787801-031
For use in Korea
787801-AD1
For use in the United States
787801-001
For use in Latin America
787801-161
Backlit keyboard for 14–inch models (includes backlight and keyboard cables):
82
For use in Belgium
787294-A41
For use in the Netherlands
787294-B31
For use in Brazil
787294-201
For use in Northwest Africa
787294-FP1
For use in Bulgaria
787294-261
For use in Norway
787294-091
For use in Canada
787294-DB1
For use in Portugal
787294-131
For use in the Czech Republic and Slovakia
787294-FL1
For use in Romania
787294-271
For use in Denmark
787294-051
For use in Russia
787294-251
For use in France
787294-041
For use in Saudi Arabia
787294-171
For use in Germany
787294-151
For use in Slovenia
787294-BA1
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
For use in country or region
Spare part
number
For use in country or region
Spare part number
For use in Greece
787294-211
For use in Spain
787294-071
For use in Hungary
787294-061
For use in Sweden and Finland
787294-B71
For use in Iceland
787294-DD1
For use in Switzerland
787294-BG1
For use in India
787294-D61
For use in Taiwan
787294-AB1
For use in Israel
787294-BB1
For use in Thailand
787294-281
For use in Italy
787294-061
For use in Turkey
787294-141
For use in Japan
787294-291
For use in the United Kingdom
787294-031
For use in Korea
787294-AD1
For use in the United States
787294-001
For use in Latin America
787294-161
Before removing the keyboard, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64).
5.
Remove the service cover (see Service cover on page 65).
6.
Remove the optical drive (see Optical drive on page 77).
Remove the keyboard:
1.
Loosen the two captive screws that secure the keyboard to the computer.
Component replacement procedures
83
84
2.
Open the computer.
3.
Insert a thin tool (1) to loosen the tabs on the rear edge of the keyboard (2), and then lift the rear edge
of the keyboard (3).
4.
Swing the rear edge of the keyboard (1) up and forward until it rests upside down on the palm rest.
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
5.
For models without a pointing stick, remove the metal shield (2) covering the zero insertion force (ZIF)
connector, release the ZIF connector to which the keyboard cable is attached (3), remove the keyboard
cable (4), and then remove the keyboard (5).
Component replacement procedures
85
6.
For models with a pointing stick, disconnect the pointing stick cable from the system board (32), release
the zero insertion force (ZIF) connector to which the keyboard cable is attached (3), remove the
keyboard cable (4), and then remove the keyboard (5)
Reverse this procedure to install the keyboard.
86
Chapter 5 Removal and replacement procedures for Customer Self-Repair parts
6
Removal and replacement procedures for
Authorized Service Provider parts
CAUTION: Components described in this chapter should only be accessed by an authorized service provider.
Accessing these parts can damage the computer or void the warranty.
Fan and heat sink assembly
NOTE: The fan and heat sink assembly spare part kit includes replacement thermal material.
Description
Spare part number
Fan
738685-001
Heat sink for computer models with Intel UMA graphics memory
738686-001
Heat sink for computer models with discrete graphics
738393-001
Before removing the fan and heat sink assembly, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
Remove the fan:
1.
Disconnect the fan cable (1) from the system board, loosen the two captive screws (2), and then
remove the fan.
Fan and heat sink assembly
87
2.
Remove the heat sink assembly:
NOTE: Due to the adhesive quality of the thermal material located between the heat sink assembly
and the system board components, it may be necessary to move the heat sink assembly from side to
side to detach it.
●
88
For computer models equipped with Intel UMA graphics, following the 1 through 4 sequence
stamped into the processor heat sink, loosen the four Phillips captive screws that secure the
processor heat sink to the system board, and then remove the heat sink (2).
Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
●
For computer models equipped with discrete graphics, following the 1 through 2 sequence
stamped into the graphics board heat sink, remove the 2 captive screws (1). Following the 1
through 4 sequence stamped into the processor heat sink, loosen the four Phillips captive screws
that secure the processor heat sink to the system board (2), and then remove the heat sink
assembly (3).
NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink assembly
and the system board components each time the fan and heat sink assembly is removed. Replacement
thermal material is included with the fan/heat sink assembly, processor, and system board spare part kits.
Thermal locations for computer models equipped with Intel UMA graphics are shown in the following
illustration:
●
Various thermal pads are used on the processor (1) and the heat sink section (2) that services it.
Fan and heat sink assembly
89
Thermal locations for computer models equipped with discrete graphics are shown in the following
illustration:
●
Thermal paste is used on the processor (1) and the heat sink section (2) that services it.
●
Thermal paste is used on the graphics board processor (3) and the heat sink section (4) that services it
Reverse this procedure to install the fan/heat sink assembly.
90
Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
Base enclosure
Description
Spare part number
Base enclosure
For 15.6-in models
738692-001
For 14-in models
738681-001
Before removing the base enclosure, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
e.
Fan and heat sink assembly (see Fan and heat sink assembly on page 87)
Remove the base enclosure:
1.
Remove the rubber screw covers.
Base enclosure
91
2.
Remove the fourteen Torx T8 screws that secure the top cover to the computer.
3.
Remove the following screws that secure the base enclosure to the computer:
(1) Two Torx T8 screws in the optical drive bay
(2) Three Torx T8 screws in the battery bay
(3) Two Phillips screws
92
4.
Remove the memory card (4).
5.
Turn the computer right side up with the front toward you.
6.
Lift the front edge of the base enclosure until the left and right sides and the rear edge detach from the
computer.
7.
Disconnect the serial connector cable from the system board.
Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
8.
Remove the base enclosure, making sure that the display panel cables and the wireless antenna cables
route through the openings in the base enclosure.
Reverse this procedure to install the base enclosure.
Base enclosure
93
USB board
Description
Spare part number
USB board (includes cable)
For use in ProBook 650 G1 models equipped with a 15.6–inch display assembly
738702-001
For use in ProBook 655 G1 models equipped with a 15.6–inch display assembly
745891-001
For use in computer models equipped with a 14–inch display assembly
738400-001
Before removing the USB board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
e.
Base enclosure (see Base enclosure on page 91)
Remove the USB board:
1.
94
Remove the four Phillips screws (3) that secure the USB board to the base enclosure.
Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
2.
Lift up on the left side to disconnect the connector interface (2).
3.
Detach the USB board cable from the base enclosure (3), and remove the USB board and cable.
Reverse this procedure to install the USB board.
USB board
95
Power button board
Description
Spare part number
Power button board (includes cable)
For 15.6-in models
738701-001
For 14-in models
738399-001
Before removing the power button board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
e.
Base enclosure (see Base enclosure on page 91)
Remove the power button board:
96
1.
Turn the top cover upside down, with the front toward you.
2.
Remove the Phillips PM2.0×3.0 screw (1) that secures the power button board to the top cover.
3.
Release the clips (2) that secure the power button board to the top cover.
Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
4.
Remove the power button board (3) and cable.
Reverse this procedure to install the power button board.
Power button board
97
Fingerprint reader board
Description
Spare part number
Fingerprint reader board (includes cable and double-sided adhesive)
738394-001
Before removing the fingerprint reader board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
e.
Base enclosure (see Base enclosure on page 91)
Remove the fingerprint reader board:
98
1.
Turn the top cover upside down with the front toward you.
2.
Detach the fingerprint reader board cable (1) from the top cover. (The fingerprint reader board cable is
attached to the top cover with tape.)
3.
Remove the Phillips screw (2) that secures the fingerprint reader board and bracket to the top cover.
Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
4.
Slide the fingerprint reader board (2) bracket forward and remove the fingerprint reader board and
cable(4).
Reverse this procedure to install the fingerprint reader board.
Fingerprint reader board
99
Smart card reader
Description
Spare part number
Smart card reader for 15.6–in models with TouchPad (includes cable)
748958-001
Smart card reader for 14-in models with 2-button TouchPad (includes cable)
738398-001
Smart card reader for 14-in models with 4-button TouchPad (includes cable)
744005-001
Before removing the smart card reader, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
e.
Base enclosure (see Base enclosure on page 91)
Remove the smart card reader:
1.
Release the ZIF connector (1) to which the smart card reader cable is attached, and then disconnect the
smart card reader cable from the system board.
2.
Remove the two Torx screws (2) that secure the smart card reader to the base enclosure.
3.
Remove the smart card reader (3).
100 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
Reverse this procedure to install the smart card reader and cable.
System board
NOTE: The system board spare part kit includes battery connector bracket and replacement
thermal material.
Description
Spare part number
For 14-in. computer models with shared memory and WWAN capability (includes replacement thermal
material)
744007-001
For 14-in. computer models with shared memory and the Windows 8 Standard operating system with
WWAN capability (includes replacement thermal material)
744007-501
For 14-in. computer models with shared memory and the Windows 8 Professional operating system
with WWAN capability (includes replacement thermal material)
744007-601
For 14-in. computer models with discrete memory and WWAN capability (includes replacement thermal
material)
744008-001
For 14-in. computer models with discrete memory and the Windows 8 Standard operating system with
WWAN capability (includes replacement thermal material)
744008-501
For 14-in. computer models with discrete memory and the Windows 8 Professional operating system
with WWAN capability (includes replacement thermal material)
744008-601
For 14-in. computer models with discrete memory, WWAN capability (includes replacement thermal
material)
744009-001
For 14-in. computer models with discrete memory and the Windows 8 Standard operating system with
WWAN capability (includes replacement thermal material)
744009-501
For 14-in. computer models with shared memory and the Windows 8 Professional operating system
with WWAN capability (includes replacement thermal material)
744009-601
For 14-in. computer models with discrete memory and WWAN capability (includes replacement thermal
material)
744010-001
For 14-in. computer models with discrete memory and the Windows 8 Standard operating system with
WWAN capability (includes replacement thermal material)
744010-501
For 14-in. computer models with shared memory and the Windows 8 Professional operating system
with WWAN capability (includes replacement thermal material)
744010-601
For 15.6-in. computer models with discrete memory, WWAN capability (includes replacement thermal
material)
744015-001
For 15.6-in. computer models with discrete memory and the Windows 8 Standard operating system with
WWAN capability (includes replacement thermal material)
744015-501
For 15.6-in. computer models with discrete memory and the Windows 8 Professional operating system
with WWAN capability (includes replacement thermal material)
744015-601
For 15.6-in. computer models with shared memory, WWAN capability (includes replacement thermal
material)
744016-001
For 15.6-in. computer models with shared memory and the Windows 8 Standard operating system with
WWAN capability (includes replacement thermal material)
744016-501
For 15.6-in. computer models with shared memory and the Windows 8 Professional operating system
with WWAN capability (includes replacement thermal material)
744016-601
For 15.6-in. computer models with shared memory, WWAN capability (includes replacement thermal
material)
744017-001
System board 101
Description
Spare part number
For 15.6-in. computer models with shared memory and the Windows 8 Standard operating system with
WWAN capability (includes replacement thermal material)
744017-501
For 15.6-in. computer models with shared memory and the Windows 8 Professional operating system
with WWAN capability (includes replacement thermal material)
744017-601
For 14-in. computer models equipped with shared memory with WWAN capability
745883-001
For 14-in. computer models equipped with shared memory and the Windows 8 Standard
operating system with WWAN capability
745883-501
For 14-in. computer models with shared memory and the Windows 8 Professional operating system
with WWAN capability
745883-601
For 14-in. computer models shared memory without WWAN capability
745884-001
For computer models equipped with shared memory and the Windows 8 Standard operating system
without WWAN capability
745884-501
For use only on computer models shared memory and the Windows 8 Professional operating system
without WWAN capability
745884-601
For use only on 15.6-in. computer models equipped with an Intel Quad Core processor with WWAN
capability
745887-001
For use only on 15.6-in. computer models shared memory and the Windows 8 Standard
operating system with WWAN capability
745887-501
For use only on 15.6-in. computer models with shared memory and the Windows 8 Professional
operating system with WWAN capability
745887-601
For use only on 15.6-in. computer models with shared memory and the Windows 8 Standard
operating system without WWAN capability
745888-501
For use only on 15.6-in. computer models with shared memory and the Windows 8 Professional
operating system without WWAN capability
745888-601
For use only on 15.6-in. computer models with shared memory and without WWAN capability
745888-001
Before removing the system board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Fan/heat sink assembly (see Fan and heat sink assembly on page 87)
e.
Keyboard (see Keyboard on page 80)
f.
Display assembly (see Display assembly on page 116)
102 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
g.
Base enclosure (see Base enclosure on page 91)
h.
USB board (see USB board on page 94)
NOTE: When replacing the system board, be sure that the following components are removed from the
defective system board and installed on the replacement system board:
●
WWAN module (see WWAN module (select models only) on page 74)
●
Solid-state drive (see Solid-state drive on page 79)
●
WLAN module (see WLAN module on page 75)
●
Expansion memory (see Primary memory module on page 69)
●
Primary memory (see Expansion memory module on page 72)
●
Smart card reader (see Smart card reader on page 100)
●
Processor (see Processor on page 109)
Remove the system board:
1.
Disconnect the following cables from the system board:
(1) Card reader cable
(2) Power connector cable
Left (3) and right (4)speaker cables
(5) Display panel cable (if display panel is still attached)
System board 103
2.
Remove the five Torx screws (1) and the Phillips screw (2) that secure the system board to the
base enclosure.
3.
Lift up on the left side of the system board (1) until it rests at an angle.
4.
Remove the system board (2) by sliding it up and to the left at an angle.
Reverse this procedure to install the system board.
104 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
Speakers
Description
Spare part number
Speakers (includes cable)
738404-001
Before removing the speakers, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
e.
Base enclosure (see Base enclosure on page 91)
Remove the speakers:
1.
Disconnect the speaker cables (1) and (4) from the system board.
2.
Remove the two Phillips PM2.0×3.0 screws (2) and (5) that secure the speakers to the base enclosure.
Speakers 105
3.
Remove the speakers (3) and (6) and cables.
Reverse this procedure to install the speakers.
106 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
Function button board
Description
Spare part number
Function button board (includes cable and double-sided adhesive)
For use in models equipped with a 15.6–inch display assembly
738703-001
For use in models equipped with a 14–inch display assembly
738401-001
Before removing the function button board, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
e.
Base enclosure (see Base enclosure on page 91)
Remove the function button board:
1.
Turn the top cover upside down, with the front toward you.
2.
Disconnect the function button board cable (1).
3.
Remove the Phillips PM2.0×3.0 screws (2) that secures the function button board to the top cover.
Function button board 107
4.
Lift the function button board (3) to remove it.
Reverse this procedure to install the function button board.
108 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
Processor
NOTE: The processor spare part kit includes replacement thermal material.
Description
Spare part number
Intel Dual Core i7-4600M 2.80-GHz processor (3.0-MB L3 cache, 37 W)
737330-001
Intel Dual Core i5-4330M 2.80-GHz processor (3.0-MB L3 cache, 37 W)
738201-001
Intel Dual Core i5-4300M 2.60-GHz processor (3.0-MB L3 cache, 37 W)
738309-001
Intel Dual Core i5-4200M 2.50-GHz processor (3.0-MB L3 cache, 37 W)
737328-001
Intel Dual Core i3-4100M 2.50-GHz processor (3.0-MB L3 cache, 37 W)
737474-001
Intel Dual Core i3-4000M 2.40-GHz (SC turbo up to 3.30-GHz) processor (1600-MHz FSB, 3.0-MB L3
cache, 37 W)
737327-001
AMD A10-5750M with Radeon HD 8650G Graphics (quad-core; 3.5 GHz/2.5 GHz; 35W, 4 MB L2 cache)
713548-001
AMD A10-4600M with Radeon HD 7660G Graphics (quad-core; 3.2 GHz/2.3 GHz; 35W; 4 MB L2 cache)
683046-001
AMD A8-4500M with Radeon HD 7640G Graphics (quad-core; 2.8 GHz/1.9 GHz; 35W; 4 MB L2 cache)
683048-001
AMD A6-4400M with Radeon HD 7520G Graphics (dual-core; 3.2 GHz/2.7 GHz; 35W; 1 MB L2 cache)
683047-001
A6-5350M with Radeon HD 8450G Graphics (dual-core; 3.5 GHz/2.9 GHz; 35W; 1 MB L2 cache)
713550-001
AMD A4-4300M with Radeon HD 7420G Graphics (dual-core; 3.0 GHz/2.5 GHz; 35W; 1 MB L2 cache)
685990-001
AMD A4-5150M with Radeon HD 8350G Graphics (dual-core; 3.3 GHz/2.7 GHz; 35W; 1 MB L2 cache)
713549-001
AMD A8-5550M 3.1 GHz/2.1 GHz 4M 35W
713551-001
Before removing the processor, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
e.
Base enclosure (see Base enclosure on page 91)
f.
Fan and heat sink assembly (see Fan and heat sink assembly on page 87)
Remove the processor:
1.
Use a Torx8 screw driver to turn the processor locking screw one-half turn counterclockwise (1), until
you hear a click.
Processor 109
2.
Lift the processor (2) straight up, and remove it.
NOTE: The gold triangle (3) on the processor must be aligned with the triangle icon embossed on the
processor socket (4) when you install the processor.
Reverse this procedure to install the processor.
110 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
TouchPad
Description
Spare part number
Top cover
For use on HP ProBook 655 G1 models:
Top cover with 2-button TouchPad
745889-001
Top cover with 2-button TouchPad and bracket
738710-001
Top cover with 4-button TouchPad
745890–001
Top cover with 4-button TouchPad and bracket
738711–001
Top cover with 2-button TouchPad and backlit keyboard
805782–001
For use on HP ProBook 650 G1 models:
Top cover with 2-button TouchPad
738708-001
Top cover with 2-button TouchPad and bracket
738710-001
Top cover with 4-button TouchPad
738709–001
Top cover with 4-button TouchPad and bracket
738711–001
Top cover with 2-button TouchPad and backlit keyboard
805782–001
For use on models equipped with a 14–inch display assembly:
Top cover with 2-button TouchPad
738405-001
Top cover with 2-button TouchPad and bracket
738407-001
Top cover with 4-button TouchPad
738406–001
Top cover with 4-button TouchPad and bracket
738408–001
Top cover with 2-button TouchPad and backlit keyboard
805783–001
Before removing the top cover, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
NOTE: When replacing the top cover, be sure to remove the following components from the defective top
cover and install them on the replacement top cover:
TouchPad 111
●
Function button board (see Function button board on page 107)
●
Power button board (see Power button board on page 96)
●
Fingerprint reader board (see Fingerprint reader board on page 98)
Remove the TouchPad:
1.
Remove the four Torx screws (1) that secure the TouchPad to the top cover.
2.
Release the clip (2), and then remove the TouchPad (3).
Reverse this procedure to install the TouchPad.
112 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
Power connector cable
Description
Spare part number
For use on models equipped with a 15.6–inch display assembly
738694-001
For use on models equipped with a 14–inch display assembly
738683-001
Before removing the power connector cable, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64), and then remove the following components:
a.
Service cover (see Service cover on page 65)
b.
Hard drive (see Hard drive on page 66)
c.
Optical drive (see Optical drive on page 77)
d.
Keyboard (see Keyboard on page 80)
e.
Base enclosure (see Base enclosure on page 91)
f.
USB board (see USB board on page 94)
g.
Speakers (see Speakers on page 105)
h.
Fan and heat sink assembly (see Fan and heat sink assembly on page 87)
Remove the power connector cable:
1.
Disconnect the power connector cable (1) from the system board.
2.
Release the power connector cable (2) from the clips built into the base enclosure.
Power connector cable 113
3.
Release the power connector (3) from the clips and mold built into the base enclosure.
4.
Remove the power connector cable.
Reverse this procedure to install the power connector cable.
RTC battery
Description
Spare part number
RTC battery (includes cable and double-sided adhesive)
651948-001
Before removing the RTC battery, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64).
5.
Remove the service cover (see Service cover on page 65).
Remove the RTC battery:
1.
Disconnect the RTC battery cable (1) from the system board.
114 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
2.
Detach the RTC battery (2) from the base enclosure. (The RTC battery is attached to the base enclosure
with double-sided adhesive.)
3.
Remove the RTC battery and cable.
Reverse this procedure to install the RTC battery.
RTC battery 115
Display assembly
NOTE: The display panel is spared as raw panel only. The Raw Panel Support Kit is also required for full
display assembly replacement.
Description
Spare part number
15.6-in WLED FHD, UWVA display panel
739998-001
15.6-in WLED HD, UWVA display panel
739997-001
14-in HD AG WLED SVA eDP FLT display panel
747751-001
14-in HD+ AG WLED SVA eDP FLT display panel
747752-001
14-in FHD AG WLED UWVA eDPslim PSR display panel
747753-001
Raw Panel Support Kit (includes LCD back cover and wireless antennas and transceivers):
For use in models equipped with a 15.6–inch display assembly
738691-001
For use in models equipped with a 14–inch display assembly
738680–001
To remove the display assembly and access the display assembly subcomponents, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see Battery on page 64).
Remove the display assembly:
1.
Open the computer.
2.
If it is necessary to replace the display bezel or any of the display assembly subcomponents:
a.
Flex the inside edges of the top edge (1), the left and right sides (2), and the bottom edge (3) of
the display bezel until the bezel disengages from the display enclosure.
116 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
b.
Remove the display bezel (4).
The display bezel is available using spare part numbers 734301-001 (for use only on computer
models equipped with a webcamera) and 734302-001 (for use only on computer models not
equipped with a webcamera).
3.
If it is necessary to replace the display panel:
a.
Remove the four Phillips PM2.0×3.0 screws that secure the display panel to the display enclosure.
CAUTION: Before turning the display panel upside down, make sure the work surface is clear of
tools, screws, and any other foreign objects. Failure to follow this caution can result in damage to
the display panel.
Display assembly 117
4.
b.
Lift the top edge of the display panel (1) and swing it up and forward until it rests upside down in
front of the display enclosure.
c.
Release the adhesive strip (2) that secures the display panel cable connector to the display panel,
and then disconnect the display panel cable from the display panel.
d.
Remove the display panel.
Remove the six Torx T8 screws (1) and the 2 Torx screws that secure the hinge bracket to the computer.
118 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
5.
Remove the WLAN and WWAN transceiver (1) and the hinge brackets (2).
The hinge bracket is available using spare part number 738699-001.
6.
Remove the display panel cable and the wireless transceiver.
7.
If it is necessary to replace the webcamera/microphone module or microphone module:
CAUTION: Handle the webcamera/microphone module and microphone module with caution. These
modules have a thin profile and are susceptible to damage when not handled carefully.
a.
Disconnect the webcamera/microphone module cable (1) from the webcamera/
microphone module.
Display assembly 119
b.
Detach the webcamera/microphone module (2) from the display enclosure. (The webcamera/
microphone module is attached to the display enclosure with double-sided adhesive.)
c.
Remove the webcamera/microphone module.
The webcamera/microphone module is available using spare part number 738409-001. The
microphone module is available using spare part number 738397-001.
Reverse this procedure to reassemble and install the display assembly.
120 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts
7
Computer Setup
Windows 8 — Computer Setup (BIOS), MultiBoot, and System
Diagnostics
Using Computer Setup
Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and
output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup
includes settings for the types of devices installed, the startup sequence of the computer, and the amount of
system and extended memory.
NOTE: Use extreme care when making changes in Computer Setup. Errors can prevent the computer from
operating properly.
Starting Computer Setup
NOTE: An external keyboard or mouse connected to a USB port can be used with Computer Setup only if
USB legacy support is enabled.
To start Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2.
press f10 to enter Computer Setup.
Navigating and selecting in Computer Setup
To navigate and select in Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
NOTE: You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard
to navigate and make selections in Computer Setup.
2.
press f10 to enter Computer Setup.
●
To select a menu or a menu item, use the tab key and the keyboard arrow keys and then
press enter, or use a pointing device to click the item.
●
To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the
screen, or use the up arrow key or the down arrow key on the keyboard.
●
To close open dialog boxes and return to the main Computer Setup screen, press esc, and then
follow the on-screen instructions.
To exit Computer Setup menus, choose one of the following methods:
●
To exit Computer Setup menus without saving your changes:
Click the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions.
– or –
Windows 8 — Computer Setup (BIOS), MultiBoot, and System Diagnostics 121
Use the tab key and the arrow keys to select Main > Ignore Changes and Exit, and then press enter.
●
To save your changes and exit Computer Setup menus:
Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select Main > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Restoring default settings in Computer Setup
NOTE: Restoring default will not change the hard drive mode.
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2.
press f10 to enter Computer Setup.
3.
Use a pointing device or the arrow keys to select Main > Restore Defaults.
4.
Follow the on-screen instructions.
5.
To save your changes and exit, click the Save icon in the lower-right corner of the screen, and then
follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the default settings.
Updating the BIOS
Updated versions of the BIOS may be available on the HP website.
Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs.
Some download packages contain a file named Readme.txt, which contains information regarding installing
and troubleshooting the file.
Determining the BIOS version
To determine whether available BIOS updates contain later BIOS versions than those currently installed on
the computer, you need to know the version of the system BIOS currently installed.
BIOS version information (also known as ROM date and System BIOS) can be displayed by pressing fn+esc (if
you are already in Windows) or by using Computer Setup.
1.
Start Computer Setup.
2.
Use a pointing device or the arrow keys to select Main > System Information.
3.
To exit Computer Setup without saving your changes, click the Exit icon in the lower-right corner of the
screen, and then follow the on-screen instructions.
– or –
122 Chapter 7 Computer Setup
Use the tab key and the arrow keys to select Main > Ignore Changes and Exit, and then press enter.
Downloading a BIOS update
CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation, download and
install a BIOS update only when the computer is connected to reliable external power using the AC adapter.
Do not download or install a BIOS update while the computer is running on battery power, docked in an
optional docking device, or connected to an optional power source. During the download and installation,
follow these instructions:
Do not disconnect power on the computer by unplugging the power cord from the AC outlet.
Do not shut down the computer or initiate Sleep.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
1.
Access the HP website, http://www.hp.com.
2.
Select Support, and then select Download drivers.
3.
Enter the product name in the text box, and then select Go.
4.
Select your computer model, and then select your operating system.
5.
In the BIOS section, follow these steps:
a.
Identify the most recent BIOS update and compare it to the BIOS version currently installed on
your computer. Make a note of the date, name, or other identifier. You may need this information
to locate the update later, after it has been downloaded to your hard drive.
b.
Follow the on-screen instructions to download your selection to the hard drive. If the update is
more recent than your BIOS, make a note of the path to the location on your hard drive where the
BIOS update is downloaded. You will need to access this path when you are ready to install the
update.
NOTE: If you connect your computer to a network, consult the network administrator before installing any
software updates, especially system BIOS updates.
BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the
download is complete. If no instructions are displayed, follow these steps:
1.
From the Start screen, type e, and then click File Explorer.
2.
Click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3.
Using the hard drive path you recorded earlier, open the folder on your hard drive that contains the
update.
4.
Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
5.
Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file
from your hard drive.
Windows 8 — Computer Setup (BIOS), MultiBoot, and System Diagnostics 123
Using MultiBoot
About the boot device order
As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is
enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include
optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices
contain bootable media or files that the computer needs to start and operate properly.
NOTE: Some boot devices must be enabled in Computer Setup before they can be included in the boot
order.
You can change the order in which the computer searches for a boot device by changing the boot order in
Computer Setup. You can also press esc while the “press the ESC key for Startup Menu” message is displayed
at the bottom of the screen, and then press f9. Pressing f9 displays a menu that shows the current boot
devices and allows you to select a boot device. Or, you can use MultiBoot Express to set the computer to
prompt you for a boot location each time the computer turns on or restarts.
Choosing MultiBoot preferences
You can use MultiBoot in the following ways:
●
To set a new boot order that the computer uses each time it is turned on, by changing the boot order in
Computer Setup.
●
To dynamically choose the boot device, by pressing esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen, and then pressing f9 to enter the Boot Device Options
menu.
●
To use MultiBoot Express to set variable boot orders. This feature prompts you for a boot device each
time the computer is turned on or restarted.
Setting a new boot order in Computer Setup
To start Computer Setup and set a boot device order that the computer uses each time it is turned on or
restarted, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2.
press f10 to enter Computer Setup.
3.
Use a pointing device or the arrow keys to select Advanced > Boot Options > UEFI Boot Order for UEFI
Hybrid or UEFI Native Boot Mode or select Advanced > Boot Options > Legacy Boot Order for Legacy
Boot Mode, and then press enter.
4.
To move the device up in the boot order, use a pointing device to click the up arrow, or press the + key.
– or –
To move the device down in the boot order, use a pointing device to click the down arrow, or press the key.
5.
To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
124 Chapter 7 Computer Setup
Dynamically choosing a boot device using the f9 prompt
To dynamically choose a boot device for the current startup sequence, follow these steps:
1.
Open the Select Boot Device menu by turning on or restarting the computer, and then pressing esc while
the “press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
press f9.
3.
Use a pointing device or the arrow keys to select a boot device, and then press enter.
Setting a MultiBoot Express prompt
To start Computer Setup and set the computer to display the MultiBoot startup location menu each time
the computer is started or restarted, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2.
press f10 to enter Computer Setup.
3.
Use a pointing device or the arrow keys to select Advanced > Boot Options > MultiBoot Express Boot
Popup Delay (Sec), and then press enter.
4.
In the MultiBoot Express Popup Delay (Sec) field, enter the length of time in seconds that you want
the computer to display the startup location menu before it defaults to the current MultiBoot setting.
(When 0 is selected, the Express Boot startup location menu is not displayed.)
5.
To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Entering MultiBoot Express preferences
When the Express Boot menu is displayed during startup, you have the following choices:
●
To specify a boot device from the Express Boot menu, select your preference within the allotted time,
and then press enter.
●
To prevent the computer from defaulting to the current MultiBoot setting, press any key before the
allotted time expires. the computer will not start until you select a boot device and press enter.
●
To allow the computer to start according to the current MultiBoot settings, wait for the allotted time to
expire.
Using HP PC Hardware Diagnostics (UEFI) (select models only)
HP PC Hardware Diagnostics is a Unified Extensible Firmware Interface (UEFI) that allows you to run
diagnostic tests to determine if the computer hardware is functioning properly. The tool runs outside of the
operating system to isolate hardware failures from issues that may be caused by the operating system or
other software components.
To start System Diagnostics:
1.
Turn on or restart the computer, quickly press esc, and then press f2.
After pressing f2, the BIOS searches three places for the HP PC Hardware Diagnostics (UEFI) tools in the
following order:
Windows 8 — Computer Setup (BIOS), MultiBoot, and System Diagnostics 125
a.
Connected USB drive
NOTE:
2.
To download the HP PC Hardware Diagnostics (UEFI) tool to a USB drive, see .
b.
Hard drive
c.
BIOS
Click the type of diagnostic test you want to run, and then follow the on-screen instructions.
NOTE: If you need to stop a diagnostics test while it is running, press esc.
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device
NOTE: The HP PC Hardware Diagnostics (UEFI) download instructions are provided in English only.
1.
Go to http://www.hp.com.
2.
Select Support, and then select Download drivers.
3.
Enter the product name in the text box, and then click Search.
4.
Select your computer model, and then select your operating system.
5.
In the Diagnostic section, click HP UEFI Support Environment.
– or –
Select Download, and then select Run.
Windows 7 — Computer Setup (BIOS), MultiBoot, and HP PC
Hardware Diagnostics (UEFI)
Using Computer Setup
Computer Setup, or Basic Input/Output System (BIOS), controls communication between all the input and
output devices on the system (such as disk drives, display, keyboard, mouse, and printer). Computer Setup
includes settings for the types of devices installed, the startup sequence of the computer, and the amount of
system and extended memory.
NOTE: Use extreme care when making changes in Computer Setup. Errors can prevent the computer from
operating properly.
Starting Computer Setup
NOTE: An external keyboard or mouse connected to a USB port can be used with Computer Setup only if
USB legacy support is enabled.
To start Computer Setup, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2.
press f10 to enter Computer Setup.
Navigating and selecting in Computer Setup
To navigate and select in Computer Setup, follow these steps:
126 Chapter 7 Computer Setup
1.
Turn on or restart the computer, and then press esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
NOTE: You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard
to navigate and make selections in Computer Setup.
2.
press f10 to enter Computer Setup.
●
To select a menu or a menu item, use the tab key and the keyboard arrow keys and then
press enter, or use a pointing device to click the item.
●
To scroll up and down, click the up arrow or the down arrow in the upper-right corner of the
screen, or use the up arrow key or the down arrow key on the keyboard.
●
To close open dialog boxes and return to the main Computer Setup screen, press esc, and then
follow the on-screen instructions.
To exit Computer Setup menus, choose one of the following methods:
●
To exit Computer Setup menus without saving your changes:
Click the Exit icon in the lower-right corner of the screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select Main > Ignore Changes and Exit, and then press enter.
●
To save your changes and exit Computer Setup menus:
Click the Save icon in the lower-right corner of the screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select Main > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
Restoring factory settings in Computer Setup
NOTE: Restoring defaults will not change the hard drive mode.
To return all settings in Computer Setup to the values that were set at the factory, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2.
press f10 to enter Computer Setup.
3.
Use a pointing device or the arrow keys to select Main > Restore Defaults.
4.
Follow the on-screen instructions.
5.
To save your changes and exit, click the Save icon in the lower-right corner of the screen, and then
follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Your changes go into effect when the computer restarts.
NOTE: Your password settings and security settings are not changed when you restore the default settings.
Windows 7 — Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) 127
Updating the BIOS
Updated versions of the BIOS may be available on the HP website.
Most BIOS updates on the HP website are packaged in compressed files called SoftPaqs.
Some download packages contain a file named Readme.txt, which contains information regarding installing
and troubleshooting the file.
Determining the BIOS version
To determine whether available BIOS updates contain later BIOS versions than those currently installed on
the computer, you need to know the version of the system BIOS currently installed.
BIOS version information (also known as ROM date and System BIOS) can be displayed by pressing fn+esc (if
you are already in Windows) or by using Computer Setup.
1.
Start Computer Setup.
2.
Use a pointing device or the arrow keys to select Main > System Information.
3.
To exit Computer Setup without saving your changes, click the Exit icon in the lower-right corner of the
screen, and then follow the on-screen instructions.
– or –
Use the tab key and the arrow keys to select Main > Ignore Changes and Exit, and then press enter.
Downloading a BIOS update
CAUTION: CAUTION: To reduce the risk of damage to the computer or an unsuccessful installation,
download and install a BIOS update only when the computer is connected to reliable external power using the
AC adapter. Do not download or install a BIOS update while the computer is running on battery power, docked
in an optional docking device, or connected to an optional power source. During the download and
installation, follow these instructions:
Do not disconnect power on the computer by unplugging the power cord from the AC outlet.
Do not shut down the computer or initiate Sleep.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
1.
Access the HP website, http://www.hp.com.
2.
Click Support, and then select Download drivers.
3.
Enter the product name in the text box, and the click Go.
4.
Select your computer model, and then select your operating system.
5.
In the BIOS section, follow these steps:
a.
Identify the most recent BIOS update and compare it to the BIOS version currently installed on
your computer. Make a note of the date, name, or other identifier. You may need this information
to locate the update later, after it has been downloaded to your hard drive.
b.
Follow the on-screen instructions to download your selection to the hard drive. If the update is
more recent than your BIOS, make a note of the path to the location on your hard drive where the
BIOS update is downloaded. You will need to access this path when you are ready to install the
update.
NOTE: If you connect your computer to a network, consult the network administrator before installing any
software updates, especially system BIOS updates.
128 Chapter 7 Computer Setup
BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the
download is complete. If no instructions are displayed, follow these steps:
1.
Select Start > Computer.
2.
Click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3.
Using the hard drive path you recorded earlier, open the folder on your hard drive that contains the
update.
4.
Double-click the file that has an .exe extension (for example, filename.exe). The BIOS
installation begins.
5.
Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded file
from your hard drive.
Using MultiBoot
About the boot device order
As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is
enabled at the factory, controls the order in which the system selects a boot device. Boot devices can include
optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices. Boot devices
contain bootable media or files that the computer needs to start and operate properly.
NOTE: Some boot devices must be enabled in Computer Setup before they can be included in the boot
order.
You can change the order in which the computer searches for a boot device by changing the boot order in
Computer Setup. You can also press esc while the “press the ESC key for Startup Menu” message is displayed
at the bottom of the screen, and then press f9. Pressing f9 displays a menu that shows the current boot
devices and allows you to select a boot device. Or, you can use MultiBoot Express to set the computer to
prompt you for a boot location each time the computer turns on or restarts.
Choosing MultiBoot preferences
You can use MultiBoot in the following ways:
●
To set a new boot order that the computer uses each time it is turned on, by changing the boot order in
Computer Setup.
●
To dynamically choose the boot device, by pressing esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen, and then pressing f9 to enter the Boot Device Options
menu.
●
To use MultiBoot Express to set variable boot orders. This feature prompts you for a boot device each
time the computer is turned on or restarted.
Setting a new boot order in Computer Setup
To start Computer Setup and set a boot device order that the computer uses each time it is turned on
or restarted, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2.
press f10 to enter Computer Setup.
Windows 7 — Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) 129
3.
Use a pointing device or the arrow keys to select Advanced > Boot Options > UEFI Boot Order for UEFI
Hybrid or UEFI Native Boot Mode or select Advanced > Boot Options > Legacy Boot Order for Legacy
Boot Mode, and then press enter.
4.
To move the device up in the boot order, use a pointing device to click the up arrow, or press the + key.
– or –
To move the device down in the boot order, use a pointing device to click the down arrow, or press the key.
5.
To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Dynamically choosing a boot device using the f9 prompt
To dynamically choose a boot device for the current startup sequence, follow these steps:
1.
Open the Select Boot Device menu by turning on or restarting the computer, and then pressing esc while
the “press the ESC key for Startup Menu” message is displayed at the bottom of the screen.
2.
press f9.
3.
Use a pointing device or the arrow keys to select a boot device, and then press enter.
Setting a MultiBoot Express prompt
To start Computer Setup and set the computer to display the MultiBoot startup location menu each time the
computer is started or restarted, follow these steps:
1.
Turn on or restart the computer, and then press esc while the “press the ESC key for Startup Menu”
message is displayed at the bottom of the screen.
2.
press f10 to enter Computer Setup.
3.
Use a pointing device or the arrow keys to select Advanced > Boot Options > MultiBoot Express Boot
Popup Delay (Sec), and then press enter.
4.
In the MultiBoot Express Popup Delay (Sec) field, enter the length of time in seconds that you want the
computer to display the startup location menu before it defaults to the current MultiBoot setting.
(When 0 is selected, the Express Boot startup location menu is not displayed.)
5.
To save your changes and exit Computer Setup, click the Save icon in the lower-left corner of the
screen, and then follow the on-screen instructions.
– or –
Use the arrow keys to select Main > Save Changes and Exit, and then press enter.
Entering MultiBoot Express preferences
When the Express Boot menu is displayed during startup, you have the following choices:
130 Chapter 7 Computer Setup
●
To specify a boot device from the Express Boot menu, select your preference within the allotted time,
and then press enter.
●
To prevent the computer from defaulting to the current MultiBoot setting, press any key before the
allotted time expires. The computer will not start until you select a boot device and press enter.
●
To allow the computer to start according to the current MultiBoot settings, wait for the allotted time to
expire.
Windows 7 — Computer Setup (BIOS), MultiBoot, and HP PC Hardware Diagnostics (UEFI) 131
Using HP PC Hardware Diagnostics (UEFI) (select models only)
HP PC Hardware Diagnostics is a Unified Extensible Firmware Interface (UEFI) that allows you to run
diagnostic tests to determine if the computer hardware is functioning properly. The tool runs outside of the
operating system to isolate hardware failures from issues that may be caused by the operating system or
other software components.
To start HP PC Hardware Diagnostics UEFI:
1.
Turn on or restart the computer, quickly press esc, and then press f2.
After pressing f2, the BIOS searches three places for the HP PC Hardware Diagnostics (UEFI) tools in the
following order:
a.
Connected USB drive
NOTE: To download the HP PC Hardware Diagnostics (UEFI) tool to a USB drive, see Downloading
HP PC Hardware Diagnostics (UEFI) to a USB device on page 132.
2.
b.
Hard drive
c.
BIOS
Click the type of diagnostic test you want to run, and then follow the on-screen instructions.
NOTE:
If you need to stop a diagnostic test while it is running, press esc.
Downloading HP PC Hardware Diagnostics (UEFI) to a USB device
NOTE: The HP PC Hardware Diagnostics (UEFI) download instructions are provided in English only.
1.
Go to http://www.hp.com.
2.
Click Support, and then click Download drivers.
3.
Enter the product name in the text box, and then click Search.
4.
Select your computer model, and then select your operating system.
5.
In the Diagnostic section, click HP UEFI Support Environment.
– or –
Click Download, and then select Run.
132 Chapter 7 Computer Setup
8
Specifications
Computer specifications
Metric
U.S.
Width
37.8 cm
14.88 in
Depth
25.7 cm
10.12 in
Height (front to rear, display assembly)
2.53 cm
0.99 in
Height (front to rear, LED display assembly)
2.9
1.14 in
Weight (computer equipped with 9-cell battery, ODD
weight saver, UMA, no FPR, 1 SODIMM, WLAN only, SSD,
touchpad only, no camera, no WWAN)
2.5 kg
5.51 lb
Weight (computer equipped with 3-cell battery, ODD
weight saver, UMA, no FPR, 1 SODIMM, WLAN only, SSD,
touchpad only, no camera, no WWAN)
2.32 kg
5.10 lb
Dimensions
Input power
Operating voltage and current
19.5 V dc @ 3.33 A – 65 W, Smart AC Adapter (select models only)
119.5 V dc @ 4.62 A – 90 W, Smart AC Adapter (select models only)
Temperature
Operating
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity (non-condensing)
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating
-15 m to 12,192 m
-50 ft to 40,000 ft
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The device operates well within this range of
temperatures.
Hard drive specifications
1-TB, 5400-rpm*
750-GB, 5400-rpm**
500-GB, 5400-rpm**
9.5 mm
9.5 mm
9.5 mm
Dimensions
Height
Computer specifications 133
1-TB, 5400-rpm*
750-GB, 5400-rpm**
500-GB, 5400-rpm**
Length
100.4 mm
100.4 mm
100.4 mm
Width
69.9 mm
69.9 mm
69.9 mm
Weight
110 g
110 g
110 g
Interface type
SATA
SATA
SATA
Synchronous (maximum)
1.1 GB/sec
1.1 GB/sec
1.1 GB/sec
Security
ATA security
ATA security
ATA security
Single track
1.5 ms
1.5 ms
1.5 ms
Average (read/write)
11/13 ms
11/13 ms
11/13 ms
Maximum
22 ms
22 ms
22 ms
Logical blocks
1,953,525,168
1,465,149,168
976,766,112
Transfer rate
Seek times (typical read, including setting)
Disk rotational speed
Operating temperature
5400 rpm
0°C to 60°C (32°F to 140°F)
*1 TB = 1 trillion bytes when referring to hard drive storage capacity. Actual accessible capacity is less.
**1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less.
NOTE:
Certain restrictions and exclusions apply. Contact technical support for details.
Hard drive specifications (continued)
500-GB, 5400-rpm**
320-GB, 5400-rpm**
Height
9.5 mm
9.5 mm
Length
100.4 mm
100.4 mm
Width
69.9 mm
69.9 mm
Weight
110 g
110 g
Interface type
SATA
SATA
Synchronous (maximum)
1.1 GB/sec
1.1 GB/sec
Security
ATA security
ATA security
1.5 ms
1.5 ms
1.5 ms
11/13 ms
11/13 ms
11/13 ms
22 ms
22 ms
22 ms
Dimensions
Transfer rate
Seek times (typical read, including setting)
134 Chapter 8 Specifications
500-GB, 5400-rpm**
320-GB, 5400-rpm**
Single track
1.5 ms
1.5 ms
Average (read/write)
11/13 ms
11/13 ms
Maximum
22 ms
22 ms
Logical blocks
976,773,168
628,142,448
Disk rotational speed
5400 rpm
Operating temperature
0°C to 60°C (32°F to 140°F)
*1 TB = 1 trillion bytes when referring to hard drive storage capacity. Actual accessible capacity is less.
**1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less.
NOTE:
Certain restrictions and exclusions apply. Contact technical support for details.
Hard drive specifications (continued) 135
9
Backup and recovery
Windows 8
To protect your information, use Windows backup and restore utilities to back up individual files and folders,
back up your entire hard drive, create system repair media (select models only) by using the installed optical
drive (select models only) or an optional external optical drive, or create system restore points. In case of
system failure, you can use the backup files to restore the contents of your computer.
From the Start screen, type restore, click Settings, and then select from the list of displayed options.
NOTE: For detailed instructions on various backup and restore options, perform a search for these topics in
Windows Help and Support.
In case of system instability, HP recommends that you print the recovery procedures and save them for later
use.
NOTE: Windows includes the User Account Control feature to improve the security of your computer. You
may be prompted for your permission or password for tasks such as installing software, running utilities, or
changing Windows settings. For more information, see Windows Help and Support.
Backing up your information
Recovery after a system failure is as good as your most recent backup. You should create system repair
media and your initial backup immediately after initial system setup. As you add new software and data files,
you should continue to back up your system on a regular basis to maintain a reasonably current backup. The
system repair media (select models only) are used to start up (boot) the computer and repair the operating
system in case of system instability or failure. Your initial and subsequent backups allow you to restore your
data and settings if a failure occurs.
For more information on the Windows backup features, see Windows Help and Support.
Performing a system recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
●
Windows recovery tools: You can use Windows Backup and Restore to recover information you have
previously backed up. You can also use Windows Automatic Repair to fix problems that might prevent
Windows from starting correctly.
●
f11 recovery tools: You can use the f11 recovery tools to recover your original hard drive image. The
image includes the Windows operating system and software programs installed at the factory.
NOTE: If you are unable to boot (start up) your computer and you cannot use the system repair media you
previously created (select models only), you must purchase Windows operating system media to reboot the
computer and repair the operating system. For additional information, see Using Windows operating system
media (purchased separately) on page 138.
Using the Windows recovery tools
To recover information you previously backed up, see Windows Help and Support for steps on restoring files
and folders.
To recover your information using Automatic Repair, follow these steps:
136 Chapter 9 Backup and recovery
CAUTION: Some Startup Repair options will completely erase and reformat the hard drive. All files you have
created and any software installed on the computer are permanently removed. When reformatting is
complete, the recovery process restores the operating system, as well as the drivers, software, and utilities
from the backup used for recovery.
1.
If possible, back up all personal files.
2.
If possible, check for the presence of the Recovery Image partition and the Windows partition.
From the Start screen, type file, and then click File Explorer.
– or –
From the Start screen, type pc, and then select This PC.
NOTE: If the Windows partition and the Recovery Image partition are not listed, you must recover your
operating system and programs using the Windows operating system DVD and the Driver Recovery
media (both purchased separately). For additional information, see Using Windows operating system
media (purchased separately) on page 138.
3.
If the Windows partition and the Recovery Image partition are listed, restart the computer by pressing
and holding the shift key while clicking Restart.
4.
Select Troubleshoot, select Advanced Options, and then select Startup Repair.
5.
Follow the on-screen instructions.
NOTE: For additional information on recovering information using the Windows tools, perform a search for
these topics in Windows Help and Support.
Using f11 recovery tools
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files that you
have created and any software that you have installed on the computer are permanently removed. The f11
recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory.
Software not installed at the factory must be reinstalled.
To recover the original hard drive image using f11:
1.
If possible, back up all personal files.
2.
If possible, check for the presence of the Recovery Image partition: From the Start screen, type pc, and
then select This PC.
NOTE: If the Recovery Image partition is not listed, you must recover your operating system and
programs using the Windows operating system media and the Driver Recovery media (both purchased
separately). For additional information, see Using Windows operating system media (purchased
separately) on page 138.
3.
If the Recovery Image partition is listed, restart the computer, and then press esc while the “Press the
ESC key for Startup Menu” message is displayed at the bottom of the screen.
4.
Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5.
Follow the on-screen instructions.
Windows 8 137
Using Windows operating system media (purchased separately)
To order a Windows operating system DVD, contact support. See the Worldwide Telephone Numbers booklet
included with the computer. You can also find contact information from the HP website. Go to
http://www.hp.com/support, select your country or region, and follow the on-screen instructions. .
CAUTION: Using a Windows operating system media completely erases hard drive contents and reformats
the hard drive. All files that you have created and any software that you have installed on the computer are
permanently removed. When reformatting is complete, the recovery process helps you restore the operating
system, as well as drivers, software, and utilities.
To initiate a full install of the operating system using a Windows operating system DVD:
NOTE: This process takes several minutes.
1.
If possible, back up all personal files.
2.
Insert the Windows operating system DVD into the optical drive, and then restart the computer.
3.
When prompted, press any keyboard key.
4.
Follow the on-screen instructions.
After the installation is completed:
1.
Eject the Windows operating system media and then insert the Driver Recovery media.
2.
Install the Hardware Enabling Drivers first, and then install Recommended Applications.
138 Chapter 9 Backup and recovery
Using Windows Refresh or Windows Reset
When your computer is not working properly and you need to regain system stability, the Windows Refresh
option allows you to start fresh and keep what is important to you.
The Windows Reset option allows you to perform detailed reformatting of your computer, or remove
personal information before you give away or recycle your computer. For more information on these
features, see Windows Help and Support.
Using HP Software Setup
HP Software Setup can be used to reinstall drivers or select software that has been corrupted or deleted from
the system.
1.
From the Start screen, type HP Software Setup.
2.
Open HP Software Setup.
3.
Follow the on-screen directions to reinstall drivers or select software.
Windows 8 139
Windows 7
Your computer includes HP and Windows tools to help you safeguard your information and retrieve it if you
ever need to. These tools will help you return your computer to a proper working state, all with simple steps.
This section provides information about the following processes:
●
Creating recovery media and backups
●
Restoring and recovering your system
Creating recovery media and backups
Recovery after a system failure is only as good as your most recent backup.
1.
After you successfully set up the computer, create HP Recovery media. This step creates a Windows 7
operating system DVD and a Driver Recovery DVD. The Windows DVD can be used to reinstall the original
operating system in cases where the hard drive is corrupted or has been replaced. The Driver Recovery
DVD installs specific drivers and applications. See Creating recovery media with HP Recovery Disc
Creator (select models only) on page 140.
2.
Use Windows Backup and Recovery tools to perform the following:
●
Back up individual files and folders
●
Back up your entire hard drive (select models only)
●
Create system repair discs (select models only) with the installed optical drive (select models only)
or an optional external optical drive
●
Create system restore points
NOTE: This guide describes an overview of backing up, restoring, and recovering options. For more details
about the tools provided, see Help and Support. To access Help and Support, select Start > Help and
Support.
NOTE: HP recommends that you print the recovery procedures and save them for later use, in case of
system instability.
In case of system failure, you can use the backup files to restore the contents of your computer. See Backing
up your information on page 141.
Guidelines
●
When creating recovery media or backing up to discs, use any of the following types of discs (purchased
separately): DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend on the
type of optical drive you are using.
●
Be sure that the computer is connected to AC power before you start the recovery media creation
process or the backup process.
Creating recovery media with HP Recovery Disc Creator (select models only)
HP Recovery Disc Creator is a software program that offers an alternative way to create recovery media.
After you successfully set up the computer, you can create recovery media using HP Recovery Disc Creator.
This recovery media allows you to reinstall your original operating system as well as select drivers and
applications if the hard drive becomes corrupted. HP Recovery Disc Creator can create two kinds of recovery
DVDs:
140 Chapter 9 Backup and recovery
●
Windows 7 operating system DVD—Installs the operating system without additional drivers or
applications.
●
Driver Recovery DVD—Installs specific drivers and applications only, in the same way that the HP
Software Setup utility installs drivers and applications.
Creating recovery media
NOTE: The Windows 7 operating system DVD can be created only once. Thereafter, the option to create that
media will not be available after you create a Windows DVD.
To create the Windows DVD:
1.
Select Start > All Programs > Productivity and Tools > HP Recovery Disc Creator.
2.
Select Windows disk.
3.
From the drop-down menu, select the drive for burning the recovery media.
4.
Click the Create button to start the burning process.
After the Windows 7 operating system DVD has been created, create the Driver Recovery DVD:
1.
Select Start > All Programs > Productivity and Tools > HP Recovery Disc Creator.
2.
Select Driver disk.
3.
From the drop-down menu, select the drive for burning the recovery media.
4.
Click the Create button to start the burning process.
Backing up your information
You should create system repair media and your initial backup immediately after initial system setup. As you
add new software and data files, you should continue to back up your system on a regular basis to maintain a
reasonably current backup. You should also create Windows system repair media (select models only) which
can be used to start up (boot) the computer and repair the operating system in case of system instability or
failure. Your initial and subsequent backups allow you to restore your data and settings if a failure occurs.
You can back up your information to an optional external hard drive, a network drive, or discs.
Note the following when backing up:
●
Store personal files in the Documents library, and back it up regularly.
●
Back up templates that are stored in their associated directories.
●
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot of your
settings. The screen shot can be a time-saver if you have to reset your preferences.
●
When backing up to discs, number each disc after removing it from the drive.
NOTE: For detailed instructions on various backup and restore options, perform a search for these topics in
Help and Support. To access Help and Support, select Start > Help and Support.
NOTE: Windows includes the User Account Control feature to improve the security of your computer. You
may be prompted for your permission or password for tasks such as installing software, running utilities, or
changing Windows settings. Refer to Help and Support. To access Help and Support, select Start > Help and
Support.
To create a backup using Windows Backup and Restore:
NOTE: The backup process may take over an hour, depending on file size and the speed of the computer.
Windows 7 141
1.
Select Start > All Programs > Maintenance > Backup and Restore.
2.
Follow the on-screen instructions to set up your backup, create a system image (select models only), or
create system repair media (select models only).
Performing a system recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
●
Windows recovery tools: You can use Windows Backup and Restore to recover information you have
previously backed up. You can also use Windows Startup Repair to fix problems that might prevent
Windows from starting correctly.
●
f11 recovery tools (select models only): You can use the f11 recovery tools to recover your original hard
drive image. The image includes the Windows operating system and software programs installed at the
factory.
NOTE: If you are unable to boot (start up) your computer and you cannot use the system repair media you
previously created (select models only), you must purchase Windows 7 operating system media to reboot
the computer and repair the operating system. For additional information, see Using Windows 7 operating
system media on page 144.
142 Chapter 9 Backup and recovery
Using the Windows recovery tools
Using the Windows recovery tools, you can:
●
Recover individual files
●
Restore the computer to a previous system restore point
●
Recover information using recovery tools
NOTE: For detailed instructions on various recovery and restore options, perform a search for these topics
in Help and Support. To access Help and Support, select Start > Help and Support.
NOTE: Windows includes the User Account Control feature to improve the security of your computer. You
may be prompted for your permission or password for tasks such as installing software, running utilities, or
changing Windows settings. Refer to Help and Support. To access Help and Support, select Start > Help and
Support.
To recover information you previously backed up:
1.
Select Start > All Programs > Maintenance > Backup and Restore.
2.
Follow the on-screen instructions to recover your system settings, your computer (select models only),
or your files.
To recover your information using Startup Repair, follow these steps:
CAUTION: Some Startup Repair options will completely erase and reformat the hard drive. All files you have
created and any software installed on the computer are permanently removed. When reformatting is
complete, the recovery process restores the operating system, as well as the drivers, software, and utilities
from the backup used for recovery.
1.
If possible, back up all personal files.
2.
If possible, check for the presence of the Windows partition.
To check for the Windows partition, select Start > Computer.
NOTE: If the Windows partition is not listed, you must recover your operating system and programs
using the Windows 7 operating system DVD and the Driver Recovery media. For additional information,
see Using Windows 7 operating system media on page 144.
3.
If the Windows partition is listed, restart the computer, and then press f8 before the Windows operating
system loads.
4.
Select Startup Repair.
5.
Follow the on-screen instructions.
NOTE: For additional information on recovering information using the Windows tools, select Start > Help
and Support.
Using f11 recovery tools (select models only)
CAUTION: Using f11 completely erases hard drive contents and reformats the hard drive. All files that you
have created and any software that you have installed on the computer are permanently removed. The f11
recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory.
Software not installed at the factory must be reinstalled.
To recover the original hard drive image using f11:
Windows 7 143
1.
If possible, back up all personal files.
2.
If possible, check for the presence of the HP Recovery partition: click Start, right-click Computer, click
Manage, and then click Disk Management.
NOTE: If the HP Recovery partition is not listed, you must recover your operating system and
programs using the Windows 7 operating system media and the Driver Recovery media. For additional
information, see Using Windows 7 operating system media on page 144.
3.
If the HP Recovery partition is listed, restart the computer, and then press esc while the “Press the ESC
key for Startup Menu” message is displayed at the bottom of the screen.
4.
Press f11 while the “Press <F11> for recovery” message is displayed on the screen.
5.
Follow the on-screen instructions.
Using Windows 7 operating system media
If you cannot use the recovery media you previously created using the HP Recovery Disc Creator (select
models only), you must purchase a Windows 7 operating system DVD to reboot the computer and repair the
operating system.
To order a Windows 7 operating system DVD, go to the HP website. For U.S. support, go to
http://www.hp.com/support. For worldwide support, go to http://welcome.hp.com/country/us/en/
wwcontact_us.html. You can also order the DVD by calling support. For contact information, see the
Worldwide Telephone Numbers booklet included with the computer.
CAUTION: Using a Windows 7 operating system DVD completely erases hard drive contents and reformats
the hard drive. All files that you have created and any software that you have installed on the computer are
permanently removed. When reformatting is complete, the recovery process helps you restore the operating
system, as well as drivers, software, and utilities.
To initiate recovery using a Windows 7 operating system DVD:
NOTE: This process takes several minutes.
1.
If possible, back up all personal files.
2.
Restart the computer, and then insert the Windows 7 operating system DVD into the optical drive before
the Windows operating system loads.
3.
When prompted, press any keyboard key.
4.
Follow the on-screen instructions.
5.
Click Next.
6.
Select Repair your computer.
7.
Follow the on-screen instructions.
After the repair is completed:
1.
Eject the Windows 7 operating system DVD and then insert the Driver Recovery DVD.
2.
Install the Hardware Enabling Drivers first, and then install Recommended Applications.
144 Chapter 9 Backup and recovery
SUSE Linux – Backup and recovery
Recovery after a system failure is as good as your most recent backup. As you add new software and data
files, you should continue to back up your system on a regular basis to maintain a reasonably current backup.
Your computer includes tools provided by HP to help you safeguard your information and retrieve it if ever
needed.
Creating backups
1.
Create restore media immediately after you set up the computer.
2.
As you add files, routinely create a backup of your system and personal information.
Backing up your information
You should back up your computer files on a regular schedule to maintain a current backup. You can
manually back up your information to an optional external drive, a network drive, or discs. Back up your
system at the following times:
●
At regularly scheduled times
●
Before the computer is repaired or restored
●
Before you add or modify hardware or software
To back up your home directory files using Backup Manager Settings:
1.
Select Computer > More Applications > Tools > Backup Manager Settings, and click Backup my home
directory.
2.
Click Storage Destination Location, and then select a location to back up your information.
3.
Click Schedule, and then select a time schedule to perform backups at a regularly scheduled time.
To immediately back up your information, click the Backup Now check box.
NOTE: Before you back up your information, be sure you have designated a location to save the
backup files.
4.
Click Save and Backup to start the backup and to save the backup settings.
To restore backup files:
1.
Select Computer > More Applications > Tools > Backup Manager Restore.
2.
Click Backup Source, and then select the location of the backup files.
3.
Click Restore Destination, and then select the destination to restore the files.
4.
To restore all files from the selected location, click Restore all files. To restore select files only, click
Restore selected files, click Select Files and then select the files to be restored.
5.
Under Restore Point, click the time and date of the backup.
NOTE: If multiple backups have been performed, click Use the latest version to restore the latest
version.
6.
Click Restore to start restoring the files, or click Cancel to cancel the operation.
SUSE Linux – Backup and recovery 145
Performing a system recovery
Recovery allows you to repair or restore the computer to its original factory state. You can create an HP
Factory Image Restore DVD, using an installed or an external DVD±RW optical drive.
CAUTION: Using Recovery completely erases hard drive contents and reformats the hard drive. All files you
have created and any software installed on the computer are permanently removed. The recovery tool
reinstalls the original operating system and HP programs and drivers that were installed at the factory.
Software, drivers, and updates not installed by HP must be manually reinstalled. Personal files must be
restored from a backup.
To restore the computer using the HP Factory Image Restore DVD, you must first create the recovery disc. To
create the recovery disc:
NOTE: HP recommends that you create the HP Factory Image Restore DVD in the event of a system failure.
1.
Select Computer > More Applications.
2.
In the left pane, click Tools, and then click Create HP Factory Image Restore DVD in the right pane.
3.
Follow the on-screen instructions to create an image file to burn a recovery disc.
To restore the computer from the recovery disc, follow these steps:
1.
If possible, back up all personal files.
2.
Insert the HP Factory Image Restore DVD into the optical drive and restart the computer.
3.
As the computer is restarting, press f9 to open the Computer Setup boot option menu.
4.
Press the down arrow to select Restore SLED HP-BNB preload image from the Linux boot menu, and
then press enter.
5.
Using the arrow keys, select Yes when prompted: Do you want to start the System-Restore?
6.
Follow the on-screen instructions.
Remove everything and reinstall SLED
Sometimes you want to perform detailed reformatting of your computer, or you want to remove personal
information before you give away or recycle your computer. The process described in this section provides a
speedy, simple way to return the computer to its original state. This option removes all personal data,
applications, and settings from your computer, and reinstalls the Linux operating system.
IMPORTANT: This option does not provide backups of your information. Before using this option, back up
any personal information you wish to retain.
You can initiate this option by using the f11 key.
To use the f11 key:
Press f11 while the computer boots.
– or –
Press and hold f11 as you press the power button.
The following options are available:
●
Cancel/Reboot—Reboots the system. No recovery or restore activity is performed.
146 Chapter 9 Backup and recovery
●
Recover/Repair System—This option repairs a system that is not working properly and preserves user
data.
●
Restore Factory System—This option restores the system back to the original factory state. User data is
not preserved.
Select an option and follow the on-screen instructions.
SUSE Linux – Backup and recovery 147
10 Statement of Volatility
The purpose of this document is to provide general information regarding non-volatile memory in industrystandards based HP Business Notebook PC systems and provide general instructions for restoring
nonvolatile memory that can contain personal data after the system has been powered off and the hard drive
has been removed.
HP Business Notebook PC products that use Intel®-based or AMD®-based system boards contain volatile DDR
memory. The amount of nonvolatile memory present in the system depends upon the system configuration.
Intel-based and AMD-based system boards contain nonvolatile memory subcomponents as originally
shipped from HP assuming that no subsequent modifications have been made to the system and assuming
that no applications, features, or functionality have been added to or installed on the system.
Following system shutdown and removal of all power sources from an HP Business Notebook PC system,
personal data can remain on volatile system memory (DIMMs) for a finite period of time and will also remain
in nonvolatile memory. The steps below will remove personal data from the notebook PC, including the
nonvolatile memory found in Intel-based and AMD-based system boards. Some of these steps are disclosed
in the Maintenance & Service Guides available for HP PC products available on the product support pages at
www.hp.com.
1.
Follow steps (a) through (I) below to restore the nonvolatile memory that can contain personal data.
Restoring or re-programming nonvolatile memory that does not store personal data is neither
necessary nor recommended.
a.
Enter BIOS (F10) Setup by powering on the system and pressing F10 when prompted near the
bottom of the display, or press the ESC key to display the start up menu, and then press F10 . If the
system has a BIOS administrator password, enter the password at the prompt.
b.
Select the Main menu, and then select Restore Defaults.
c.
Select the Security menu, and then select Restore Security Level Defaults.
d.
If an asset or ownership tag is set, select the Security menu and scroll down to the Utilities menu.
Select System IDs, and then select Asset Tracking Number. Press the spacebar once to clear the
tag, and then press Enter to return to the prior menu.
e.
If a DriveLock password is set, select the Security menu, select Hard Drive Tools, scroll down to
DriveLock, and then clear the check box for DriveLock password on restart. Repeat this
procedure if more than one hard drive has a DriveLock password.
f.
If an Automatic DriveLock password is set, select the Security menu, select Hard Drive Tools, and
then scroll down to Automatic DriveLock. A warning screen about automatic drive lock is
displayed, Select Yes to continue. Repeat this procedure if more than one hard drive has an
Automatic DriveLock password.
g.
Select the Main menu, and then Reset BIOS Security to factory default. Click yes at the warning
message.
h.
Select the Main menu, and then Save Changes and Exit.
i.
Reboot the system. If the system has a Trusted Platform Module (TPM) and/or fingerprint sensor,
one or two prompts will appear. One to clear the TPM and the other to Reset Fingerprint Sensor;
press F1 to accept or F2 to reject.
If the HP notebook model number ends in a ‘p’ or ‘w’ and includes Intel® Centrino with VProTM,
reboot the PC and enter BIOS Setup by pressing F10 when prompted. Select System
148 Chapter 10 Statement of Volatility
Configuration, select AMT Options, and then select Un-configure AMT on next boot. Select Save,
and then select Yes. Select the File menu, and then select Save Changes and Exit. Reboot the
system and confirm that you want to un-configure AMT.
2.
j.
If the optional Intel® Anti-Theft Technology (AT) was activated, contact the provider to de-activate
it.
k.
If the optional Absolute® Software Computrace® management and tracking service was activated
on the notebook PC, contact the provider to deactivate it.
l.
Remove all power and system batteries for at least 24 hours.
Remove and retain the storage drive or clear the contents of the drive.
a.
Hard Disk Drive (HDD)
Clear the HDD contents by using the HP Disk Sanitizer® utility or a third party application that,
ideally, is U.S. Department of Defense (DOD) 5220.22-M approved.
To run HP Disk Sanitizer, enter BIOS Setup by powering on the system and pressing F10 when
prompted near the bottom of the display, or press ESC to display the startup menu, and then press
F10. Select the Security menu, scroll down to the Utilities menu, and then select Hard Drive
Tools. Select Disk Sanitizer, and then select the desired drive. For a higher level of protection,
select Optimum.
NOTE: This process will take a long time, and the amount of time varies based on the hard drive
capacity.
b.
Solid State Drive (SSD)
Clear the SSD contents by using the BIOS Setup Secure Erase command option, or by using a third
party utility designed to erase data from an SSD. To run Secure Erase, enter BIOS Setup by
powering on the system and pressing F10 when prompted near the bottom of the display. Select
the Security menu and scroll down to the Utilities menu. Select Secure Erase and select the
desired hard drive.
Non-volatile memory usage
Non Volatile
Memory Type
Amount
(Size)
Does this
memory
store
customer
data?
Does this
memory
retain data
when power
is removed?
What is the
purpose of this
memory?
How is data input into this
memory?
How is this memory write
protected?
Real Time Clock
(RTC) battery
backed-up CMOS
configuration
memory (CMOS)
256 Bytes
No
Yes
Stores system
date and time
and limited
keyboard
controller data.
Using the F10 Setup utility or
changing the Microsoft®
Windows® date & time.
This memory is not writeprotected. HP
recommends password
protecting the F10 Setup
utility.
Controller (NIC)
EEPROM
64 Kbytes
(not customer
accessible)
No
Yes
Store NIC
configuration
and NIC
firmware.
Using a utility from the NIC
vendor that can be run from
DOS.
A utility is required to
write data to this memory
and is available from NIC
vendor. Writing data to
this ROM in an
inappropriate manner will
render the NIC nonfunctional.
Non-volatile memory usage 149
Non Volatile
Memory Type
Amount
(Size)
Does this
memory
store
customer
data?
Does this
memory
retain data
when power
is removed?
What is the
purpose of this
memory?
How is data input into this
memory?
How is this memory write
protected?
Keyboard ROM
64 Kbytes
(not customer
accessible)
No
Yes
Stores firmware
code (keyboard,
mouse, &
battery
management).
Programmed at the factory.
Code is updated when the
system BIOS is updated.
A utility is required for
writing data to this
memory and is available
on the HP website. Writing
data to this ROM in an
inappropriate manner can
render the PC nonfunctional.
DIMM Serial
Presence Detect
(SPD)
configuration data
256 Bytes per
memory
module, 128
Bytes
programmabl
e (not
customer
accessible)
No
Yes
Stores memory
module
information.
Programmed by the memory
vendor.
Data cannot be written to
this memory when the
module is installed in a
PC. The specific write
protection method varies
by memory vendor.
System BIOS
4 to 5 MBytes
Yes
Yes
Store system
BIOS code and
PC
configuration
data.
System BIOS code is
programmed at the factory.
Code is updated when the
system BIOS is updated.
Configuration data and
settings are input using the
F10 setup utility or a custom
utility.
A utility is required for
writing data to this
memory and is available
on the HP website. Writing
data to this ROM in an
inappropriate manner can
render the PC nonfunctional.
Intel Management
Engine Firmware
(present only in
models ending in a
‘p’,‘w’, or ‘m’ or
with Intel Centrino
Pro technology)
1.5 or 5MByte
Yes
Yes
Stores
Management
Engine Code,
Settings,
Provisioning
Data and iAMT
third party data
store.
Management Engine Code is
programmed at the factory.
Code is updated via Intel
secure firmware update
utility. Unique Provisioning
Data can be entered at the
factory or by an administrator
using the Management Engine
(MEBx) setup utility. The third
party data store contents can
populated by a remote
management console or local
applications registered by an
administrator to have access
to the space.
The Intel chipset is
configured to enforce HW
protection to block all
direct read/write access
to this area. An Intel
utility is required for
updating the firmware.
Only firmware updates
digitally signed by Intel
can be applied using this
utility.
Bluetooth flash
2Mbit
No
Yes
Stores
Bluetooth
configuration
and firmware.
Programmed at the factory.
Tools for writing data to this
memory are not publicly
available but can be obtained
from the silicon vendor.
A utility is required for
writing data to this
memory and is made
available through newer
versions of the driver if
the flash requires an
upgrade.
802.11 WLAN
EEPROM
4kb to 8kb
No
Yes
Stores
configuration
and calibration
data.
Programmed at the factory.
Tools for writing data to this
memory are not made public.
A utility is required for
writing data to this
memory and is typically
not made available to the
public unless a firmware
upgrade is necessary to
address a unique issue.
150 Chapter 10 Statement of Volatility
Non Volatile
Memory Type
Amount
(Size)
Does this
memory
store
customer
data?
Does this
memory
retain data
when power
is removed?
What is the
purpose of this
memory?
How is data input into this
memory?
How is this memory write
protected?
Webcamera
64K bit
No
Yes
Store Web Cam
configuration
and firmware.
Using a utility from the device
manufacturer that can be run
from Windows.
A utility is required for
writing data to this
memory and is typically
not made available to the
public unless a firmware
upgrade is necessary to
address a unique issue.
Fingerprint reader
512kByte
Flash
Yes
Yes
Stores
fingerprint
templates.
By enrolling in HP
ProtectTools Security
Manager.
Only a digitally signed
application can make the
call to write to the flash.
Questions and answers
1.
2.
How can the BIOS settings be restored (returned to factory settings)?
a.
Turn on or restart the computer and press F10 when prompted near the bottom of the display.
b.
Select Main, and then select Restore defaults.
c.
Follow the on-screen instructions.
d.
Select Main, Save Changes and Exit, and then press Enter.
What kind of configuration data is stored on the DIMM Serial Presence Detect (SPD) memory
module? How would this data be written?
The DIMM SPD memory contains information about the memory module such as size, serial number,
data width, speed/timing, voltage and thermal information. This information is written by the module
manufacturer and stored on an EEPROM. This EEPROM cannot be written to when the memory module is
installed in a PC. Third party tools do exist that can write to the EEPROM when the memory module is
not installed in a PC. There are various third party tools available to read SPD memory.
3.
Does the “Firmware Hub for System BIOS” contain the BIOS program? Is this chip writable, and if so
how?
The Firmware Hub does contain the BIOS program and is writable. A utility is required to perform the
write function.
4.
In some PC systems, the Firmware Hub for System BIOS is a flash memory chip so that updates can
be written by the customer. Is this true for these BIOS chips?
Yes, they are flash memory chips.
5.
What is meant by “Restore the nonvolatile memory found in Intel-based system boards”?
This relates to clearing the Real Time Clock (RTC) CMOS memory that contains PC configuration data.
6.
Does resetting the CMOS configuration memory return the PC back to factory defaults?
The process of resetting the CMOS will return certain system settings to factory default but will not
reset many of the system data and configuration defaults to their factory settings. To return these
system data and configuration defaults to factory settings, refer to question and answer 1 and follow
the instructions for returning the BIOS settings to factory defaults.
Questions and answers 151
11 Power cord set requirements
The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC, or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the country or
region where the equipment is purchased.
Power cord sets for use in other countries and regions must meet the requirements of the country or region
where the computer is used.
Requirements for all countries
The following requirements are applicable to all countries and regions:
●
The length of the power cord set must be at least 1.0 m (3.3 ft) and no more than 2.0 m (6.5 ft).
●
All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in
the country or region where the power cord set will be used.
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage rating of
125 or 250 V AC, as required by the power system of each country or region.
●
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard Sheet
C13 connector for mating with the appliance inlet on the back of the computer. Requirements for all
countries 113
Requirements for specific countries and regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
The Netherlands
KEMA
1
Norway
NEMKO
1
The People's Republic of China
COC
5
152 Chapter 11 Power cord set requirements
Country/region
Accredited agency
Applicable note number
South Korea
EK
4
Sweden
CEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and
wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be
used.
2.
The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding type
with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall plug must
be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4.
The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
5.
The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler and wall
plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
Requirements for specific countries and regions 153
12 Recycling
When a non-rechargeable or rechargeable battery has reached the end of its useful life, do not dispose of the
battery in general household waste. Follow the local laws and regulations in your area for battery disposal.
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable
batteries. For more information about recycling programs, see the HP Web site at http://www.hp.com/
recycle.
154 Chapter 12 Recycling
Index
A
AC adapter, spare part number 44
AC adapter, spare part numbers 42
AC adapter/battery light 16
audio, product description 4
audio-in (microphone) jack,
identifying 18
audio-out (headphone) jack,
identifying 18
audio/USB board
spare part number 32
B
Backup and Restore 141
backups
creating 141
Base enclosure
spare part number 46, 49
base enclosure
removal 91
spare part number 91
base enclosure, spare part number
36
battery
removal 64
spare part numbers 37, 45, 64
battery bay, identifying 21
battery release latch 20
Blu-ray R/RE DVD±RW SuperMulti
Double-Layer Combo Drive
removal 77
spare part number 42, 55
Blu-ray R/RE DVD±RW SuperMulti
Double-Layer Drive
precautions 59
spare part number 35
Blu-ray ROM DVD±RW Combo Drive
spare part number 54, 77
Blu-ray ROM DVD±RW SuperMulti
Double-Layer Drive
precautions 59
bottom components 20
buttons
left pointing stick 15
left TouchPad 15
optical drive eject 17
power 10
right pointing stick 15
right TouchPad 15
Windows button 11, 12
C
Cable Kit
spare part number 52, 54
cables
components 39
cables, service considerations 59
caps lock light, identifying 13, 14
chipset, product description 1
components
bottom 20
display 8
front 15
left-side 16
rear 19
right-side 18
computer
major components 24
specifications 133
computer reset 146
connector, power 16, 17
connectors, service considerations
59
D
display assembly
removal 116
spare part numbers
Display bezel
spare part number
display bezel
removal 116
spare part numbers
117
Display Cable Kit
spare part number
Display cable kit
spare part number
display cable kit
illustrated 39
116
46, 49
38, 52, 54,
39
46, 49
display hinge kit
spare part number 46
display panel
product description 2
removal 117
spare part number 52
spare part numbers 38, 54, 55
dock/expansion base
spare part numbers 44
docking connector, identifying 20
Driver Recovery DVD,
creating 140
drives, preventing damage 59
Dual-Mode DisplayPort, identifying
18
DVD-ROM Drive
precautions 59
removal 77
spare part number 35, 42, 52,
54, 55, 77
DVD-ROM SuperMulti Drive
spare part number 52, 54, 55
DVD±RW Double-Layer Combo Drive
spare part number 52
DVD±RW SuperMulti Double-Layer
Drive
precautions 59
removal 77
spare part number 35, 42, 77
E
electrostatic discharge 59
embedded numeric keypad,
identifying 11
equipment guidelines 62
esc key, identifying 11, 12
Ethernet, product description 4
ExpressCard slot 17
external monitor port 18
F
f11 recovery 137
Fan
spare part number 46
Index 155
fan
removal 87
spare part numbers 87
fan and heat sink assembly
spare part numbers 36
Fingerprint bracket, illustrated 40
Fingerprint reader
spare part number 46
fingerprint reader bezel, illustrated
40
fingerprint reader board
removal 98
spare part number 32, 98
fingerprint reader board bracket
removal 99
fingerprint reader, identifying 10
flash cache, product description 3
fn key, identifying 11, 12
front components 15
Function button board
spare part number 45
function button board
removal 107
spare part number 32, 107
function keys, identifying 11, 12
fusion controller hub, product
description 1
G
graphics, product description 1
grounding guidelines 59
guidelines
equipment 62
grounding 59
packaging 61
transporting 61
workstation 61
H
hard drive
precautions 59
product description 3
removal 66
spare part numbers 36, 41, 43,
44, 45, 66
specifications 133
hard drive bracket
illustrated 41
156 Index
Hard Drive Hardware Kit
contents 41
spare part number 37, 41
Hard drive hardware kit
spare part number 46
hard drive light 16
hard drive recovery 137
hard drive, identifying 20
headphone (audio-out) jack 18
heat sink
removal 87
spare part numbers 46, 87
Heat sink assembly
spare part number 46
hinge
spare part number 39, 51
hinge bracket
removal 118
hinge cover
spare part number 119
Hinge Kit, spare part number 51
HP Recovery Disc Creator, using
140
I
integrated numeric keypad,
identifying 12
integrated webcam light,
identifying 8
internal display switch 8
internal microphones, identifying 8
J
jacks
audio-in (microphone) 18
audio-out (headphone) 18
network 16, 17
RJ-11 (modem) 19
RJ-45 (network) 16, 17
K
keyboard
product description
removal 80
spare part numbers
48, 49, 50, 51, 80
keypad
embedded numeric
integrated numeric
keys
esc 11, 12
5
25, 46, 47,
11
12
fn 11, 12
function 11, 12
Windows applications 11
L
latch, battery release 20
latches, service cover release 21
left-side components 16
lights
AC adapter/battery 16
caps lock 13, 14
hard drive 16
microphone mute 13, 14
num lock 13, 14
power 13, 14, 16
TouchPad 13, 14
webcam 8
wireless 13, 14, 16
M
mass storage device
illustrated 41
precautions 59
spare part numbers 41
Memory card reader, identifying 17
memory module
identifying 20
inserting 70
product description 2
removal 69, 72
removing 70
spare part numbers 44, 69, 72
microphone
product description 4
microphone (audio-in) jack,
identifying 18
microphone module
removal 119
spare part number 38, 46, 120
microphone mute light 13, 14
model name 1
Modem
spare part number 43
Modem module
spare part numbers 36
modem module
removal 68
spare part number 68
spare part numbers 68
modemtransfer board
spare part number 51
mouse, spare part numbers 44
N
network cable
illustrated 39
network jack, identifying 16, 17
num lock light 13, 14
O
operating system, product
description 6
optical drive
precautions 59
removal 77
spare part numbers 35, 42, 52,
54, 55, 77
optical drive blank tray
illustrated 40
optical drive eject button,
identifying 17
optical drive transfer board
spare part number 51
P
packaging guidelines 61
plastic parts, service
considerations 58
Plastics Kit
components 40
spare part number 40, 51
Plastics kit
spare part number 45
pointing device, product
description 5
pointing stick 15
ports
Dual-Mode DisplayPort 18
external monitor 18
product description 5
serial 19
power button board
removal 96
spare part number 31, 46, 51,
96
power button, identifying 10
Power cable
spare part number 46, 49
power connector board
spare part number 31
power connector cable
removal 113
power connector, identifying 16, 17
power cord
set requirements 152
spare part numbers 42, 43
power lights 13, 14, 16
power requirements, product
description 5
processor
product description 1
removal 109
spare part numbers 32, 44, 45,
46, 109
product description
audio 4
chipset 1
display panel 2
Ethernet 4
external media cards 5
flash cache 3
fusion controller hub 1
graphics 1
hard drive 3
keyboard 5
memory module 2
microphone 4
operating system 6
pointing device 5
ports 5
power requirements 5
processor 1
product name 1
security 5
serviceability 7
solid-state drive 3
Upgrade drive 3
video 4
wireless 4
product name 1
R
Raw Panel Support Kit
spare part number 25, 39, 46,
49, 116
recovery 139
recovery media, creating 140
recovery partition 137
refresh 139
removal/replacement
procedures 63
reset
computer 146
steps 146
restoring the hard drive 137
right-side components 18
RJ-11 (modem) jack, identifying 19
RJ-45 (network) jack, identifying
16, 17
RJ-45 cable
illustrated 39
RTC battery
removal 114
spare part number 44, 114
Rubber kit
spare part number 46
S
Screw Kit, spare part number 43, 49
SD card reader bezel, illustrated 40
security cable slot, identifying 18
security, product description 5
serial port, identifying 19
service considerations
cables 59
connectors 59
plastic parts 58
Service cover
spare part number 46, 49
service cover
removal 65
spare part number 37, 54, 55,
65
service cover release latch 21
service cover release lock,
identifying 20
service tag 22
serviceability, product description 7
SIM slot, identifying 20
SLED
remove everything and reinstall
option 146
slots
ExpressCard 17
security cable 18
SIM 20
smart card 17
Smart card reader
spare part numbers 52
Index 157
smart card reader
removal 100
spare part number 31, 46, 55,
100
Smart card reader blank,
illustrated 40
smart card slot 17
solid-state drive
precautions 59
product description 3
removal 79
spare part numbers 36, 41, 55,
79
Speaker kit
spare part number 45
Speaker Kit, spare part number 31
speakers
removal 105
spare part number 31, 105
speakers, identifying 10
specifications
computer 133
hard drive 133
system board
removal 101
spare part numbers 32, 52, 53,
54, 55, 101
T
tools required 58
Top cover
spare part number 45
top cover
spare part number 31, 51, 57
spare part numbers 54
top hinge cover, spare part number
25
TouchPad
buttons 15
removal 111
spare part number 32, 45, 52,
111
TouchPad light, identifying 13, 14
TouchPad zone
identifying 15
transporting guidelines 61
U
upgrade bay 17
158 Index
Upgrade drive, product description
3
USB 3.0 charging port 16, 17
USB 3.0 port 17, 18
USB board
removal 94
spare part number 45, 51, 94
spare part numbers 54
USB ports, identifying 16, 17, 18
V
vents, identifying 18, 21
video, product description 4
W
webcam 8
webcam light, identifying 8
webcam, identifying 8
Webcamera
spare part number 45
webcamera/microphone module
removal 119
spare part number 38, 120
Windows
Refresh 139
Windows 7 operating system DVD
creating 140
Windows 7 operating system media
creating 140
Windows 8 operating system DVD
138
Windows applications key,
identifying 11
Windows button, identifying 11, 12
wireless antennas, identifying 8
wireless light 13, 14, 16
wireless, product description 4
WLAN antennas, identifying 8
WLAN bracket, illustrated 40
WLAN module
removal 75
spare part numbers 36, 44, 45,
54, 75
workstation guidelines 61
WWAN antennas, identifying 8
WWAN module
removal 74
spare part numbers 37, 45, 74