- Computers & electronics
- Audio & home theatre
- Audio amplifiers
- LY International Electronics
- PB-200P/PB-300P/PB-600P/PB-1000P
- Owner's manual
LY International Electronics | PB200P | PB-200P/PB-300P/PB-600P/PB-1000P | Owner's manual | owner`s manual
Add to My manuals5 Pages
advertisement
![LY International Electronics | PB200P | PB-200P/PB-300P/PB-600P/PB-1000P | Owner's manual | owner`s manual | Manualzz LY International Electronics | PB200P | PB-200P/PB-300P/PB-600P/PB-1000P | Owner's manual | owner`s manual | Manualzz](http://s3.manualzz.com/store/data/029844400_1-a55dcac5af1b327f3f9f11352e0531ac-360x466.png)
MIXER AMPLIFIER
PB200P
PB300P
PB600P
PB1000P
O W N E R ’ S M A N U A L
Before operating, please read this manual carefully.
FEATURES
Three microphone inputs, two auxiliary inputs, and one AUX output for link.
Transformer for the speaker outputs at 100V, 70V and 4Ω.
Muting function.
Individual volume control.
Low and high tone control.
A five-element LED level meter is provided for the quick and easy visual monitoring of sound level.
The protection and alarm in case of output short-circuit.
FRONT PANEL
1 LED power indicator 6 MIC volume control
For main power. Adjust microphone volume.
2 Power switch 7 AUX volume control
For main power. Adjust AUX input volume.
3 AED level meter 8 MIC1 input jack
Indicate output level. Connect to microphone of unbalanced
4 Bass control 30-600Ω with 1/4”phone plug.
Adjust bass response. The muting function is activated
5 Treble control while the signal is sent to MIC1.
Adjust treble response.
Note:
When all the five elements of the LED level meter remain lit, it indicates that the sound is distorted. In such a case, adjust each volume controlling button, until LED element 4 (+8dB) and LED element 5(+10dB) shall flash.
REAR PANEL
1 Mute control 4 AUX output
Adjust muting function. Connect to amplifier.
2 MIC2 input & MIC3 input 5 Output terminals
Connect to the microphones at unbalanced Connect to speakers.
30-600Ω with 1/4 phone plug. 6 AC power connector
The signals from MIC2 and MIC3 will Connect to AC power source.
be muted by the signal from MIC1. 7 AC fuse
3 AUX1 input & AUX2 input Prevent the excessive AC current flow.
Connect to auxiliary source equipment. 8 Fan intake window
Note:
When connecting to speakers, use one pair of speaker output terminals only.
Connections
DECK TUNER
100V COM AUX OUT AUX2 AUX1 MIC3 MIC2
Priority MIC or Chairman’s MIC
MUTING FUNCTION
This model provides muting function. The inputs from Mic2, Mic3, Aux 1 and Aux 2 are automatically muted by the input from Mic1, as the signal from
Mic1 overrides other input signals. The level of MUTE can be adjusted within the range from MAX to MIN by adjusting MUTE control button on the rear panel. It is preset at MAX
MUTE before shipping from the factory.
MAX MIN
PRECAUTION OF INSTALLATIOM
1. Do not block ventilation holes.
2. The amplifier should not be placed in any of the areas:
1) with poor ventilation;
2) exposed to direct sunlight;
3) with high ambient temperature or adjacent to heat-generating equipment;
4) with high humidity or heavy dust;
5) susceptible to vibration.
3. Make sure the power outlet conforms to the plug of the unit.
4. Do not use this unit if the electrical power cord is frayed or broken.
Always operate the unit with the AC ground wire connected to the
electrical system’s ground.
5. If an alarm rings after the power has been on and the signal has been
fed, there must be an of output short-circuit trouble. In a such case,
please turn the power off. Do not turn on the power again, until the
trouble shall be resolved.
SPECIFICATIONS
Model
Rated output
Output regulation
Speaker output
AUX output
Input sensitivity
Frequency response
Distortion
The ratio of signal to noise
Tone
60W
PB200P PB300P
120W
PB600P
250W
Less than 3dB, from off-load to full load
Balanced 4Ω, 70V, 100V
≥1V
Mic1,2,3 : 600Ω, ≤3mV, unbalanced
AUX1,2 : 10kΩ, ≤300mV, unbalanced
50Hz -16kHz (±3dB)
< 0.5% at 1kHz , 1/3rated power
Mic1,2 and 3 : 75dB
AUX1 and 2 : 80dB
Bass : ±10dB(100Hz)
Treble : ±10dB(10kHz)
PB1000P
350W
Protection
Muting function
Power requirements
Power consumption
Outer Packing Size (mm)
Unit Size (mm)
AC fuse; DC voltage; overload; short-circuit.
Mic 1 overrides other input signals with
0-( -30 )dB attenuation
AC 220V-240V/50Hz-60Hz
120W 250W
(L×W×H)520×430×195
(L×W×H)420×338×88
Gross weight 10.3kg 10.8kg
Net weight 8.5kg 9kg
Specifications are subject to change without notice
500W
14.8kg
13kg
650W
15.2kg
13.4kg
CAUTION
● When the “Power switcher” is off, please pull out the power cord from the socket.
Please keep the equipment out of water.
● To reduce the risk of electric shock, do not remove the cover.
● No user parts inside. Refer servicing to qualified service personnel.
LY International Electronics Co. Ltd.
Http://www.lyintlcorp.com
advertisement
Related manuals
advertisement