TM-T82II EN User`s Manual

English
User’s Manual
M00057800EN
TM-T88V User’s Manual 1
English
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. While every precaution has been taken in the preparation of this book, Seiko Epson
Corporation assumes no responsibility for errors or omissions. Neither is any liability assumed for damages
resulting from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties
for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or
abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.)
failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options
or any consumable products other than those designated as Original Epson Products or Epson Approved
Products by Seiko Epson Corporation.
EPSON is a registered trademark of Seiko Epson Corporation in Japan and other countries/regions.
NOTICE: The contents of this manual are subject to change without notice.
Copyright © 2012 by Seiko Epson Corporation, Nagano, Japan.
2 TM-T82II User’s Manual
English
Standards and Approvals
The following standards are applied only to the printers that are so labeled. (EMC is tested using the
Epson power supplies.)
Oceania:
AS/NZS CISPR22 Class A
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
The connection of a non-shielded printer interface cable to this printer will invalidate the EMC standards
of this device.
You are cautioned that changes or modifications not expressly approved by Seiko Epson Corporation
could void your authority to operate the equipment.
Important Safety Information
This section presents important information intended to ensure safe and effective
use of this product. Read this section carefully and store it in an accessible
location.
Key to Symbols
The symbols in this manual are identified by their level of importance, as defined
below. Read the following carefully before handling the product.
WARNING:
Warnings must be followed carefully to avoid serious bodily injury.
CAUTION:
Cautions must be observed to avoid minor injury to yourself, damage to your
equipment, or loss of data.
Note:
Notes have important information and useful tips on the operation of your equipment.
Safety Precautions
WARNING:
Shut down your equipment immediately if it produces smoke, a strange odor, or
unusual noise. Continued use may lead to fire or shock. Immediately unplug the
equipment and contact your dealer or a Seiko Epson service center for advice.
Never attempt to repair this product yourself. Improper repair work can be
dangerous.
Never disassemble or modify this product. Tampering with this product may
result in injury, fire, or shock.
Be sure to use the specified power source (EPSON PS-180 [model: M159B]).
Connection to an improper power source may cause fire.
Do not allow foreign matter to fall into the equipment. Penetration by foreign
objects may lead to fire.
TM-T82II User’s Manual 3
English
If water or other liquid spills into this equipment, unplug the AC cable
immediately, and then contact your dealer or a Seiko Epson service center for
advice. Continued usage may lead to fire.
Do not use aerosol sprayers containing flammable gas inside or around this
product. Doing so may cause fire.
Do not connect a telephone line to the drawer kick-out connector; otherwise
the printer and the telephone line may be damaged.
CAUTION:
Do not connect cables in ways other than those mentioned in this manual.
Different connections may cause equipment damage and burning.
Be sure to set this equipment on a firm, stable, horizontal surface. The product
may break or cause injury if it falls.
Do not use in locations subject to high humidity or dust levels. Excessive humidity
and dust may cause equipment damage or fire.
Do not place heavy objects on top of this product. Never stand or lean on this
product. Equipment may fall or collapse, causing breakage and possible injury.
Take care not to injure your fingers on the manual cutter
•
When you remove printed paper
•
When you perform other operations such as loading/replacing roll
paper
To ensure safety, unplug this product before leaving it unused for an extended
period.
Caution Labels
The caution labels on the product indicate the following precautions.
CAUTION:
Do not touch the thermal head because it can be very hot after printing.
Restriction of Use
When this product is used for applications requiring high reliability/safety, such
as transportation devices related to aviation, rail, marine, automotive, etc.;
disaster prevention devices; various safety devices, etc.; or functional/precision
devices, etc.; you should use this product only after giving consideration to
including fail-safes and redundancies into your design to maintain safety and
total system reliability. Because this product was not intended for use in
applications requiring extremely high reliability/safety, such as aerospace
equipment, main communication equipment, nuclear power control equipment,
or medical equipment related to direct medical care, etc., please make your own
judgment on this product’s suitability after a full evaluation.
Downloading Drivers, Utilities, and Manuals
The latest versions of drivers, utilities, and manuals can be downloaded from the
following URL.
http://download.epson-biz.com/?service=pos
4 TM-T82II User’s Manual
English
Unpacking
The following items are included with the standard specification printer.
If any item is damaged, contact your dealer.
Note:
Depending on the model, the accessories in the broken line box in the illustration below
may not be included.
The shape of accessories varies between models and areas.
Printer
AC adapter
AC cable
Setup Guide
Power switch
cover
Rubber feet for
vertical installation
TM-T82II Software
& Documents
Disc
Power switch
waterproof cover
Control panel label for
vertical installation
Roll paper
Wall hanging
bracket
Screws for wall
hanging bracket
58-mm width
paper guide plate
TM-T82II User’s Manual 5
English
Part Names
Roll paper cover
Control panel
Cutter cover
Cover open lever
Power switch
Control Panel
(Power) LED
This LED is on when the printer is on.
Error LED
This indicates an error.
Paper LED
On indicates a paper out. Flashing indicates standby.
Note:
To make the Paper LED light up when the roll paper is nearly out, enable the paper nearend sensor with the utility software for the TM-T82II, and use the printer horizontally
(with the paper exit on top).
Feed button
This button feeds paper.
6 TM-T82II User’s Manual
English
Connecting the Cables
CAUTION:
For using a serial interface, use a null modem cable.
For using a parallel interface, use an IEEE 1284 cable.
For using a USB interface, do not turn on the printer before installing the printer
driver.
For using an Ethernet (10Base-T/100Base-TX) interface, do not connect a
telephone line or a drawer kick-out cable to the Ethernet connector.
When LAN cables are installed outdoors, make sure devices without proper
surge protection are cushioned by being connected through devices that do
have surge protection. Otherwise, the devices can be damaged by lightning.
1.
2.
Make sure the printer is turned off.
Connect the interface cable to the printer.
For the shape of each connector, see the illustration below. (Mounted
interfaces vary by the printer model.)
IEEE1284
RS-232
DK
㩷
10BASE-T/
100BASE-TX
DC24V
(Drawer kick-out
connector)
USB
Note:
When connecting the USB cable, fix the USB cable with the hook shown in the illustration
below to prevent the cable from coming off.
Hook
3.
4.
Connect the other end of the interface cable to the computer.
Connect the AC cable to the AC adapter.
TM-T82II User’s Manual 7
English
5.
Connect the DC cable of the AC adapter to the power connector of the printer.
6.
Insert the AC plug into a power outlet.
Installing the Printer
You can install the printer horizontally on a flat surface (with the paper exit on
top) or vertically (with the paper exit at the front). Also, you can hang it on a wall
using the included accessories.
CAUTION:
Take measures to prevent the printer from moving by vibration during paper
cutting and when using a drawer. Affixing tape is provided as an option.
Installing the Printer Vertically
When installing the printer vertically, be sure to attach the included control panel
label for vertical installation on the roll paper cover, and attach 4 rubber feet in the
rectangular indents in the printer case, as shown in the illustration below.
Control panel label for
vertical installation
Rubber feet
8 TM-T82II User’s Manual
English
Note:
You can install the printer so that the roll paper cover is upright to the mounting surface
using the included wall hanging bracket.
1. Attach the control panel label for vertical installation on the roll paper cover.
2. Install the wall hanging bracket on the printer, and fix it using 2 included screws.
3. Attach 2 rubber feet in the rectangular indents in the printer case, and attach 2
rubber feet within the scribed line on the hanging bracket.
4. Place the printer with the wall-hanging-bracket-side down.
Control panel label for
vertical installation
3
Rubber feet
1
207 mm
{8.15"}
2
Wall hanging
bracket
TM-T82II User’s Manual 9
English
Hanging the Printer on a Wall
To hang the printer on the wall, follow the steps below.
CAUTION:
To fix the printer securely, install the wall hanging bracket on a wall made of
wood, concrete, or metal. The thickness of the wall should be 10 mm {0.4”} or
more.
Be sure to use metallic screws.
The screws on the wall side must have a pull-out strength of 150 N (15.3 kgf) or
more.
1.
Install 2 screws (screw diameter: 4 mm {0.16"}, head diameter: 7 to 9 mm {0.28
to 0.35"}) in the wall at an interval of 80 mm {3.15"}. Make sure the length of
the screw’s body in the wall is 10 mm {0.39"} or more, and the length outside
the wall is 3 to 4 mm {0.12 to 0.16"}.
3~ 4 mm
80 mm
7~ 9 mm
4 mm
10 mm or more
2.
3.
Remove the installed 2 screws from the printer, as shown in the illustration
below.
Install the wall hanging bracket on the printer, and fix it using the screws
removed in Step 2.
Screws
Wall hanging
bracket
10 TM-T82II User’s Manual
English
4.
Align the holes in the wall hanging bracket with the screws on the wall, and
hook it securely.
Installing Roll Paper
Follow the steps below to install the roll paper.
1. Use the cover open lever to open the roll paper cover.
Cover open lever
TM-T82II User’s Manual 11
English
2.
Remove the used roll paper core if any, and insert the roll paper. The correct
direction of the paper is shown in the illustration below.
3.
Pull out some paper, and close the roll paper cover.
When the printer power is on, the roll paper is automatically cut.
2
1
12 TM-T82II User’s Manual
English
Changing the Paper Width
You can change the paper width from 80 to 58 mm by installing the included
58-mm width paper guide plate. Follow the steps below to change the paper
width.
CAUTION:
Once you change the paper width from 80 to 58 mm, you cannot change it
back to 80 mm.
When changing the paper width, be sure to make the setting for the paper
width with the utility software for the TM-T82II.
1.
2.
Open the roll paper cover.
Align 3 projections on the 58-mm width paper guide plate with the
rectangular holes in the printer, and push it downwards.
58-mm width
paper guide plate
Rectangular holes
3.
4.
Install the roll paper.
Close the roll paper cover.
TM-T82II User’s Manual 13
English
Attaching Cover on the Power Switch
The enclosed power switch cover ensures that the power switch is not pressed
accidentally.
You can turn the power switch on and off by inserting a sharp-pointed object in
the holes in the power switch cover. To detach the cover, also use a sharp-pointed
object.
A waterproof cover for the power switch is also included.
To use these covers, install them as shown in the illustration below.
WARNING:
If an accident occurs with the power switch cover attached, unplug the AC
cable immediately. Continued use may cause fire or shock.
Power switch
cover
Power switch
waterproof cover
Troubleshooting
No lights on the control panel
Check whether the DC cable and AC cable are correctly connected to the printer
and the power outlet.
Error LED on with no printing
❏
❏
Check whether the roll paper cover is closed. If it is open, close it.
If the Paper LED is on, check whether the roll paper is correctly installed and
any roll paper remains.
Error LED flashing with no printing
❏
❏
❏
Check whether a paper jam has occurred. If paper is jammed, remove the
jammed paper referring to the description below and install the roll paper
correctly.
Printing stops if the head overheats and resumes automatically when it cools.
For other cases, turn the printer off, and after 10 seconds, back on.
14 TM-T82II User’s Manual
English
When a paper jam occurs
When a paper jam occurs, never pull out the paper forcibly. Open the roll paper
cover and remove the jammed paper.
CAUTION:
Do not touch the thermal head, because it can be very hot after printing.
If the roll paper cover does not open, follow the steps below.
1. Turn off the printer.
2. Put the fingers in the indents in both sides of the cutter cover, and slide it
toward the arrow in the illustration below to remove it.
Cutter cover
Indent
3.
Turn the knob until you see a triangle in the opening. This returns the cutter
blade to the normal position. See the operating instructions on the back of the
cutter cover.
Triangle
4.
5.
Knob
Install the cutter cover.
Open the roll paper cover and remove the jammed paper.
TM-T82II User’s Manual 15
English
Cleaning
Cleaning the Printer Case
Be sure to turn off the printer, and wipe the dirt off the printer case with a dry
cloth or a damp cloth.
CAUTION:
Never clean the product with alcohol, benzine, thinner, or other such solvents.
Doing so may damage or break the parts made of plastic and rubber.
Cleaning the Thermal Head
CAUTION:
After printing, the thermal head can be very hot. Be careful not to touch it and
to let it cool before you clean it.
Do not damage the thermal head by touching it with your fingers or any hard
object.
Turn off the printer, open the roll paper cover, and clean the thermal elements of
the thermal head with a cotton swab moistened with an alcohol solvent (ethanol
or IPA).
Epson recommends cleaning the thermal head periodically (generally every
3 months) to maintain receipt print quality.
Thermal head
16 TM-T82II User’s Manual
English
Specifications
80 mm paper width
58 mm paper width*1
Printing method
Thermal line printing
Printing speed
200 mm/s {7.87"/s} max.; 53.3 lps (3.75 mm {0.15"} feed)
Ladder bar code and 2D symbol: 100 mm/s {3.93"/s}
The above speed values are approximate.
The values are when the printer prints with density “Normal” at 25°C {77°F}.
Speed is adjusted automatically depending on the voltage applied and
head temperature.
Roll paper
(single-ply)
Width
79.5 mm ± 0.5 mm {3.13" ± 0.02"}
57.5 mm ± 0.5 mm {2.26" ± 0.02"}
Diameter Maximum outside diameter: 83 mm {3.27"}
Spool
Spool diameter: Inside: 12 mm {0.47"}; Outside: 18 mm {0.71"}
Thermal paper type
NTP080-80
Interface
Serial (RS-232)/Parallel (IEEE1284)/USB [Compliance: USB 2.0,
Communication speed: Full-speed (12 Mbps)]/Ethernet (10BASE-T/
100BASE-TX)
Power supply*2
Current
consumption
NTP058-80
AC adapter EPSON PS-180 (model: M159B) DC + 24 V ± 7%
Ready
Mean: Approx. 1.8 A
Sleep
Mean: Approx. 0.1 A
Temperature
Operating:
Storage:
5 to 45°C {41 to 113°F}
–10 to 50°C {14 to 122°F}, except for paper
Humidity
Operating:
Storage:
10 to 90% RH
10 to 90% RH, except for paper
Overall dimensions
146 × 140 × 199 mm {5.75 × 5.51 × 7.83"} (H × W × D)
Weight (mass)
Approx. 1.7 kg {3.74 lb}
Mbps: megabits per second
*1: The values are those when the paper width is changed to 58 mm by installing the 58-mm width
paper guide plate and making the paper width setting with utility software for the TM-T82II.
For how to install the 58-mm width paper guide plate, see “Changing the Paper Width” on page 13.
*2: Be sure to use a safety-standards-applied power source that meets the following specifications.
Rated output: 24 V/2.0 A or more, Maximum output: 240 VA or less.
TM-T82II User’s Manual 17