Untitled

DESCRIPTION OF CONTROLS ON FRONT CONTROL PANEL

6 9 8 19 4 17 18

MIC

MP3/USB/SD/BLUETOOTH/AUX/AM/FM RADIO PLMR20W

3 7 2 1 5 10 11

1. RESET button

2. SEL &VOL knob

3. POWER & MUTE button

4. LCD

5. MODE button

6&7. >>| and |<< buttons

8. BAND /AP button

9. CLK button

10. 1/>|| button

12 13 14 15 16

11. 2/INT button

12. 3/RPT button

13. 4/RDM button

14. 5/-10/HANG UP button

15. 6/+10/TEL button

16. AUX IN jack

17. Card slott

18. USB socke

19. BT MIC(microphone)

DESCRIPTION OF REMOTE CONTROL

20 19

1

2

3

4

5

6

8

18

17

16

15

14

13

12

11

7

1. Power button

2. Mute button

3. CLK button

4. MODE button

5. 1/>|| /TOP button

6. 2/INT button

7. 3/RPT button

8. 4/RDM button

9. 5/HANG UP button

10. 6/TEL button

11. SCAN button

12. LOC button

13. LOUD button

14. BAND button

15. ST button

16. A.P button

17. UP button

18. VOL +/VOL - button

19. SEL button

20. DOWN button

9 10

Page 1

WIRES CONNECTION

RED

WHITE

RCA OUTPUT

REAR RIGHT SPEAKER JACK

RCA OUTPUT

REAR LEFT SPEAKER JACK

RCA OUTPUT

FRONT RIGHT SPEAKER JACK

RCA OUTPUT

FRONT LEFT SPEAKER JACK

RED

WHITE

ANTENNA JACK

CONNECTOR A

1.

2.

3.

4. Memory +12V

5. Auto Antenna Output

6.

7. 12V (To Ignition Key)

8. GROUND

ISO SOCKET ISO SOCKET SKETCH

CONNECTOR B

1. Rear Right Speaker (+)

2. Rear Right Speaker (-)

3. Front Right Speaker (+)

4. Front Right Speaker (-)

5. Front Left Speaker (+)

6. Front Left Speaker (-)

7. Rear Left Speaker (+)

8. Rear Left Speaker (-)

SPECIFICATION

GENERAL

Supply Voltage DC 12V. Negative Ground

Current Consumption Max.7.5A

Power Output 4 x 60W(240W)

Number of channels 2 STEREO channels.

Unit Dimensions 178[W] X 108[D] X 50[H] mm.

FM SECTION

Frequency range 87.5MHz -107.9MHz

Effective sensitivity 3uV.

I.F Frequency 10.7MHz.

AM SECTION

Frequency Range 530KHz- 1710KHz

Effective Sensitivity 40dB.

Signal to noise 40dB

RCA LINE OUT

Output 1000mV @ MAX.

SD or USB PLAYBACK

System MP3 audio system.

Frequency characteristics 20Hz -100Hz <=5 dB

10KHz-20KHz <=5 dB.

Signal to noise (SD & USB) 50dB [1KHz]

Page 6

3. Dialing when in connection status

To make a call simply press the TEL button and enter the number you wish to

call using the mobile phone.

4. Accept/ Reject/ End Call

A) During ringing, press TEL button to accept the call.

B) During ringing, press HANG UP button to reject the call.

C) During talking, press HANG UP button to end the call.

5. Talking volume level setting

While talking, use volume control to adjust volume level, but this volume

level can not be saved.

6. Dialing or receiving calls while the unit is in sleep mode

When the car radio is in standby mode (Acc on and Power off), when dialing

or receiving a call, the car radio will power on automatically. After the call is

completed, the radio will revert to standby mode.

7. To transfer the audio of a file played by Mobile Phone to the Car Audio Player

If the mobile phone supports A2DP and could play audio or video files, when

the Mobile Phone plays an audio file(For some Mobile Phones, you must first

select Play by BT ), the playback will be transfered to the Car Audio Player.

In A2DP mode, if the Bluetooth device of the Mobile Phone supports AVRCP,

the functions of the >>|, |<< and PLAY/PAUSE buttons are the same as one

in media mode(no fast forward/backward functions for the >>|/|<< buttons).

The other buttons normally available in media mode are not available.

Page5

Common operation:

1. To turn the unit on/off .

When the unit is power Off, it may be switched On by pressing POWER button.

When the unit is switched On, press and hold POWER button for more than 1

second to turn off.

2. To select function mode

Press MODE button to change function mode as follows:

-->RADIO -->USB(after inserting USB stick)-->SD/MMC(after inserting SD card)

->AUX--> BT

When there is no media (USB/CARD), that mode will be skipped.

3. To adjust the volume level

Rotate VOL knob to adjust volume level during playback.

4. To mute or resume sound

Press MUTE button to eliminate or resume sound immediately during playback.

To resume the sound immediately, you can also rotate VOL knob to resume the

sound.

5. To set sound mode and menu

1).To set sound mode:

Press SEL button briefly and repeatedly to select mode of VOL(volume), BASS

(without preset DSP), TRE(treble)(without preset DSP), BAL(balance) and FAD

(fader) ,LOUD ON/LOUD OFF,EQ OFF(CLASSIC,POP,ROCK),DX/LOCAL,

STEREO/MONO in sequence and circulation. In each mode, the waiting

time is about 2 seconds, and when the waiting time is over, it will return to the last

display mode.

After selecting a mode, Rotate VOL KNOB to set or select.

2).To set radio area:

Press SEL button and hold for more than 2 seconds to turn on AREA EUROPE,

AREA USA mode. Rotate VOL KNOB to select.

6. To display and adjust clock

Press CLK button briefly to display time for 5 seconds on the LCD, and then

returns to its previous display unless the button is pressed again.

Press CLK button and hold for more than 1 second until the time flashes on

the LCD. Rotate the VOL KNOB to adjust the HOUR and press SEL button to

confirm. With the same method to adjust the MINUTE.

7. To reset unit

Before operating the unit for the first time, or after replacing the car battery or

changing the connections. You must reset the unit.

To reset the unit, remove the front control panel, then press RESET button with a

cuspidal object.

This operation will erase clock setting and some stored contents.

Page 2

RADIO OPERATION:

1. To select radio band

Press BAND button briefly and repeatedly to select a desired radio band in

sequence and circulation as follows:

-->FM1-->FM2-->FM3--> MW1--> MW2 .

2. To search for radio station manually or automatically

Press >>| or |<< button briefly to automatically tune up/down for a radio station

of strong signal.

Press and hold >>| or |<< button for 1 seconds switch to MANUAL seeking mode,

then Press >>| or |<< button briefly to manually tune up/down for your desired radio

stations step by step.

It will automatically switch to AUTO mode if no operation was done in about 3

seconds in the MANUAL seeking mode.

3. To store current station or turn on a preset one

1) Press one of the 6 number buttons and hold for more than 1 second to store the

current station in the preset memory bank of the number button for the current band.

In this way the unit can store 30 preset stations.

2) Press one of the 6 number buttons briefly to turn on the preset station stored in

the preset memory bank of the number button for the current band.

4. To scan for each preset station or auto search for the strongest stations

1) When pressing and holding BAND/AP button for more than 1 second, the radio

searches fro m the lowest fr equency and checks the signal strength level until the 6

strongest stations are found. And then the 6 strongest stations are preset to the

corresponding preset memory numbered bank. The auto-storage operation is

implemented in the each selected band. When the auto-storage operation is finished,

the radio executes Preset scan.

USB/Card OPERATION:

1. To insert or pull out SD card or USB stick

When needing to playback SD or USB music, insert SD card or USB stick into the

card slot or USB socket, the playing mode will be changed into SD or USB mode.

When SD card and USB stick are both inserted into the slot or socket, the playing

mode will be changed into the mode of the latter one and the play the first track of

SD or USB.

2. To select next or previous track to play

Press >>| or |<< button to select next or previous track to play.

3. To play fast forward or backward

Press and hold >>| or |<< button to play fast forward or backward.

4. To play previous or next 10th track/previous or next folder

Press 5/-10 or 6/+10 button to play previous or next 10th track;

Press and hold 5/-10 or 6/+10 button to play previous or next folder.

Page 3

5. How to use 1/>|| button

During playback, press 1/>|| button to pause playback. When in pause mode,

press 1/>|| button to play again.

Press and hold 1/>|| button to select the first track to playback.

6. To scan tracks

During playback, press INT button briefly to play the first 10 seconds of each track,

press INT button again to cancel INT function and retain playing the track currently

selected.

7. To repeat track(s)

During playback, press RPT button briefly to play the current track repeatedly, and

the LCD will display RPT ONE.

Press RPT button twice to play the tracks in the directory repeatedly, and the LCD will

display RPT DIR.

Press RPT button thrice to RPT ALL function, and the LCD will display RPT ALL.

8. To play tracks in random

During playback, press RDM button briefly to play all tracks in random. Press it again

to cancel RDM function.

9. Tracks search

Press and hold AP button, it will activate TRACK SEARCH mode . The LCD

will display TRK *** . Then rotate VOL knob to input track numbers.

For example, you want to play TRK 108, first inputting number 1,then inputting

number 0( after 0 jumps to high position), finally inputting number 8. With all

of the numbers input press SEL button for confirmation and playback.

Note: During inputting track numbers, briefly press the AP button to delete

the wrong input numbers.

Bluetooth Handsfree System:

1. Pairing

Turn on Bluetooth mode of mobile phone, then select the function for Finding

Bluetooth Device and enter it. After finishing finding, it will show the name of

Bluetooth Device if found, select it and enter it, then the LCD of the car audio

system will display CONNECT, BT ON and PHONE one by one.

2. Connection or disconnection

A) Use mobile phone to do connection or disconnection

1) In connection status, find the paired and connected Bluetooth Device, then

press the disconnection button to do disconnection.

2) In disconnection status, find the paired and disconnected Bluetooth Device,

then press the connection button to do connection.

B) When powering on (after Acc of the car was switched off ), the unit will search

and connect the last connected mobile phone automatically.

Note:

(1) PHONE appears on LCD only when in connection status.

(2) In connection status: Mobile phone transfers to car audio player whenever a

dialing takes place; Mobile phone transfers to car audio player whenever

receiving a call.

Page4