Acer
Aspire E700
Service Guide
Service guide files and updates are
available on the ACER/CSD web. For
more information, please refer to http:/
/csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates of Desktop Aspire E700 service guide.
Date
September 8, 2006
II
Chapter
Updates
first release
Copyright
Copyright© 2006 by Acer Incorporated. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of Acer
Incorporated.
III
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with
respect to the contents hereof and specifically disclaims any warranties of merchantability or
fitness for any particular purpose. Any Acer Incorporated software described in this manual is
sold or licensed “as is”. Should the programs prove defective following their purchase, the buyer
(and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary
servicing, repair, and any incidental or consequential damages resulting from any defect in the
software.
Acer is a registered trademark of Acer Incorporated.
Other brand and product names are trademarks and/or registered trademarks of their respective
holders.
IV
Conventions
The following conventions are used in this manual:
SCREEN MESSAGES
Denotes actual messages that appear on screen.
NOTE
Gives bits and pieces of additional information
related to the current topic.
WARNING
Alerts you to any damage that might result from
doing or not doing specific actions.
CAUTION
Gives precautionary measures to avoid possible
hardware or software problems.
IMPORTANT
Reminds you to do specific actions relevant to the
accomplishment of procedures.
V
Preface
Before using this information and the product it supports, please read the following general
information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's “global” product offering. To better fit local market requirements and enhance
product competitiveness, your regional office MAY have decided to extend the functionality of a
machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT
be covered in this generic service guide. In such cases, please contact your regional offices or the
responsible personnel/channel to provide you with further technical details.
2. Please note WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reason, if a part number change is made, it will not be
noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may
have a DIFFERENT part number code to those given in the FRU list of this printed Service Guide. You
MUST use the list provided by your regional Acer office to order FRU parts for repair and service of
customer machines.
VI
Table of Contents
Chapter 1 System Specification 1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Special Design Specification . . . . . . . . . . . . . 3
Wake-Up Event Specification . . . . . . . . . . . . . 4
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . 5
Main Board Placement . . . . . . . . . . . . . . . . 6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Acer Empowering Technology . . . . . . . . . 11
Empowering Technology password . . . . . .
Acer eRecovery Management . . . . . . . . . . .
Acer eDataSecurity Management . . . . . . .
Acer ePerformance Management . . . . . . .
11
12
13
15
Acer eRecovery . . . . . . . . . . . . . . . . . . . . . . 16
Create Backup . . . . . . . . . . . . . . . . . . . . . . . .
Restore from Backup . . . . . . . . . . . . . . . . . .
Create Factory Default Image CD . . . . . . . .
Re-install Bundled Software without CD . .
Change Password . . . . . . . . . . . . . . . . . . . . .
16
16
16
17
17
Acer Disc-to-Disc Recovery . . . . . . . . . . . . . 18
Restore without a Recovery CD . . . . . . . . . . 18
Multilingual Operating System Installation 18
Hardware Specification and Configuration
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Power Management Function . . . . . . . . . . 25
Device Standby Mode . . . . . . . . . . . . . . . . .
Global Standby Mode . . . . . . . . . . . . . . . . .
Suspend Mode . . . . . . . . . . . . . . . . . . . . . . .
ACPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
25
25
25
Chapter 2 Setup Utility 26
About the Setup Utility . . . . . . . . . . . . . . . 26
Control Keys . . . . . . . . . . . . . . . . . . . . . . . . . 26
TOC
VII
Entering the Setup Utility . . . . . . . . . . . . . 27
Product Information . . . . . . . . . . . . . . . . . 28
Standard CMOS Features . . . . . . . . . . . . . . 29
Advanced BIOS Features . . . . . . . . . . . . . . 30
Advanced Chipset Features . . . . . . . . . . . . 34
Integrated Peripherals . . . . . . . . . . . . . . . . 35
Power Management Setup . . . . . . . . . . . . 40
PnP/PCI Configurations . . . . . . . . . . . . . . . 42
PC Health Status . . . . . . . . . . . . . . . . . . . . . 43
Frequency Control . . . . . . . . . . . . . . . . . . . 44
Load Default Settings . . . . . . . . . . . . . . . . . .
Set Supervisor/User Password . . . . . . . . . . .
Save and Exit Setup . . . . . . . . . . . . . . . . . . .
Exit without Saving . . . . . . . . . . . . . . . . . . .
45
45
45
45
Chapter 3 Machine Disassembly and Replacement 46
General Information . . . . . . . . . . . . . . . . . 46
Before You Begin . . . . . . . . . . . . . . . . . . . . . 46
Aspire E700 Disassembly Procedure . . . . . 47
Chapter 4 Troubleshooting 53
Chapter 5 Jumper and Connector Location 54
Main Board Placement . . . . . . . . . . . . . . . 54
Introduction of Connectors and Headers . 56
System Board Jumper Setting . . . . . . . . . . . 56
System Board Header Setting . . . . . . . . . . . 56
Chapter 6 FRU (Field Replaceable Unit) List 62
Exploded Diagram . . . . . . . . . . . . . . . . . . . 63
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
VIII
TOC
Chapter 1
System Specification
Overview
Main Board
Description
Size
Max. 244 mm x 244 mm, MicroATX
Processor
• Socket type: Intel socket T LGA775 pin
• Socket quantity: one
• Intel Prescott 775 / Smithfield / Cedar Mill / Presler / Conroe, core speed
533/800/1066MHz
System Chipset
• GMCH: Intel G965
• ICH: Intel ICH8DH
• Super I/O: ITE8718
Memory
• Four DDR2 connectors
• Capacity:
• 256MB to 1GB DDR2 800/667/533 unbuffered SDRAM module support
• Feature support 2GB DDR2 800/667/533 unbuffered SDRAM module
when memory sample passes validation
• Max. 256MB to 4GB memory support
• Feature support to 8GB max. memory support when memory sample
passes validation.
• Dual-channel function enabled when plugging in two same memory
size DDR2 memory modules
Onboard Graphic
Solution
• Intel G965 on-die graphic (Intel GMA X3000) solution
• DVMT 4.0 technology support
• Enhanced 3D and clear video technology support
• Dual view function supported by Intel ADD2/ADD2+
• One D-sub VGA port on the rear side
PCI Express / PCI
Slots
• One PCI Express x16 slot
• One PCI Express x1 slot
• Two PCI 2.3 slots
FDD
• One slot for FDD
• 1.44MB / 3 mode 3.5” devices support
SATA
• Six SATA slots
• Storage type support:
• HDD / CD-ROM / CD-RW / DVD-ROM / DVD-RW / DVD+RW / DVD Dual /
DVD SuperMultiPlus / Blue-Ray ODD
Chapter 1
1
Audio
• Chip: HD audio codec ALC888 HD codec 7.1 with S/PDIF out
• Connectors support (at least):
• Rear six jacks that follow HD audio definition
• Front microphone in
• Front headphone out
• S/PDIF out header (1*4)
• AUX-in
• Front panel audio header (2*5) support
• HD de-pop CKT added
• S/N ration: 90 dB at rear output jack
LAN
• Controller: Intel ICH8DH
USB
• Controller: ICH8DH
• Ten port quantity:
• Four back panel ports
• Four ports for front daughter board
• Two ports for card reader + IR
• Connector pin: standard Intel FPIO pin definition
• Date transfer rate support: USB 2.0/1.1
1394
• Controller: Ti TSB43AB23PDTG4
• One onboard header
• One six-pin 1394 port
Front Panel IO
Header
2
Hardware Monitor
• Controller: Super I/O ITE8718
• Intel broadwater: ICH8 SST
• Voltage: Vcore / +12V / +5V / +3.3V / +12.5V / 5VSB
System LDE
Definition
• Power state LED:
• S0: blue steady
• S1/S3: blue blinking
• S4/S5: off
• Storage state LED:
• Active: blue blinking
• Idle: off
• LAN state LED:
• LAN active: blue blinking
• LAN idle: off
• Voltage bias: 5V
• Current: 10mA to 15 mA
Chapter 1
CIR & IR blaster
• Follow ITE’s pin define to support CIR & IR blaster function for Vista
home premium SKU
• Two IR blasters support
• BIOS needs to have the item to enable/disable this function. The factory
default is disabled (for XP MCE).
All Onboard
Connectors List
• Rear I/O connectors:
• One PS/2 keyboard port
• One PS/2 mouse port
• One parallel port
• One serial port
• One D-sub VGA port
• One RJ-45 LAN port
• Four USB ports (six audio jacks with MIC in and Line in definition)
• One six-pin 1394 port
• Onboard connectors:
• One LGA 775 CPU socket
• Four DDR2 memory sockets
• One PCI Express x16 socket
• One PCI Express x1 socket
• Two PCI slots
• One FDD slot
• Six SATA2 connectors
• Three 2*5 pin Intel FPIO specification USB pin connectors (follow Intel
FPIO standard specification)
• One 2*5 pin Intel FPIO specification microphone-in/headphone-out pin
connector
• One serial port 2*5 pin connector (2nd serial port)
• One AUX-in four-pin connector
• One four-pin CPU fan connector
• One three-pin system fan connector with linear circuit
• One two-pin intrusion alarm connector
• One 24-pin + four-pin ATX interface PS3/PS2 SPS connector
• One 2*7 pin front panel IO header
• One 1394 header
• One onboard buzzer
• One two-pin OBR header
• Color management for onboard connector
• Header for CIR & IR blaster function
Special Design Specification
Description
Thermal Design
• Intel MTM technology, default read/write enabled
•
•
•
•
Chapter 1
CPU overheat (120oC) power off protection
Compliant with Intel FMB 05A, 05B design
Compliant with Intel 2006 TDP
Slow boot-up fan speed design
3
Wake-Up Event Specification (Default Setting in BIOS)
S1
4
S3
S4
S5
Power Button
Enabled
Enabled
Enabled
Enabled
PS2 Keyboard/mouse
Disabled
Disabled
n/a
n/a
USB Keyboard/mouse
Enabled
Enabled
Disabled
n/a
PME
Enabled
Enabled
Enabled
Enabled
Modem (Ring)
Disabled
Disabled
Disabled
Disabled
RTC
Disabled
Disabled
Disabled
Disabled
Chapter 1
Block Diagram
Back Panel
VRD 11
4 Phase PWM
Intel ADD2/+ Card
or
VGA Connector
PCI Express x 16
External Graphics
Card
USB2.0 Port 0
USB2.0 Port 1
USB2.0 Port 3
USB2.0 Port 2
Back Panel
1394a Port 1
Front Panel
1394a Port 2
Header
USB2.0 Port 5
USB2.0 Port 4
USB2.0 Port 6
USB2.0 Port 8
USB2.0 Port 7
USB2.0 Port 9
ITE8718
Super I/O
Broadwater
GMCH
Firmware HUB
CK-505 Clock
Channel A DDR2
DIMM2
DIMM1
Channel B DDR2
DIMM2
DIMM1
LAN NINEVEH LAN
PCI Slot 2
PCI Slot 1
Slot 1
PCI Express x1
Realtek ALC888
HDA Codec
ESATA Connector 6
SATA Connector 5
SATA Connector 4
SATA Connector 3
SATA Connector 2
AHCI, RAID0,1,5,10
SATA Connector 1
Serial ATA Ş
PCI Express x1 port
SPI Flash
(BIOS)
PCI Express x1 port
DDR2 533/667/800
DDR2 533/667/800
1066/800/533 FSB
Socket T
Cedar Mill, Presler ,
Conroe & Allendale
LGA775 Processor
PCI Express x16 Port
4 Lanes
PCI I/F
ICH8
Direct Media Interface (DMI)
Controller Link
TI43AB23
LPC I/F
Floppy
Drive Connector
LPC I/F
Serial/LPT/KB/MS
5
Chapter 1
Main Board Placement
6
Chapter 1
Chapter 1
Item
Description
CPU_FAN1
CPU fan header
COM2
COM header 2
J11
Acer special requirement
J10
Acer special requirement
PWR1
24-pin power connector
FLOPPY1
Floppy connector 1
SYS_FAN1_1
System fan header 1_1 (three-pin)
CLR_CMOS
Clear CMOS
OBR
One button recovery
INTR1
Chassis intruder
FP1
Front panel switch/LED
TPM
Trusted platform module
interface
SATA_5
SATA data transfer connector 5
SATA_6
SATA data transfer connector 6
SATA_3
SATA data transfer connector 3
SATA_4
SATA data transfer connector 4
SATA_1
SATA data transfer connector 1
SATA_2
SATA data transfer connector 2
F_USB3
Front panel USB header 3
F_USB2
Front panel USB header 2
F_USB1
Front panel USB header 1
F_AUDIO1
Audio Aux Input
BIOS_SEL1
SPI & FWH BIOS select
PWR2
Four-pin power connector
KB/MS1
Keyboard & mouse PS2 port
COM1
COM port
PRT
Printer port
VGA
VGA port
1394_USB1
1394 and USB*2 port
NIC_USB
LAN and USB*2 port
Audio
Audio port
PCI-E1
PCI-Express x16 connector
BAT1
Battery connector
PCI-E2
PCI-Express x1 connector
F_1394
Front 1394 header
PCI1, PCI2
PCI connector
U25
FWH BIOS socket
U19
ICH8 series south bridge
U13
965 series north bridge
U10
LGA 775 CPU socket
DIMM1, DIMM2,
DIMM3, DIMM4
DDR2 memory connector
7
8
IR
Infrared function header
FLOPPY1
Floppy connector
BUZ1
Buzzer
Chapter 1
Front Panel
#
Chapter 1
Description
1
USB ports
2
Microphone-in jack
3
Speaker-out/Line-out port
4
Power button
5
CD reject button
6
Optical drive door
7
3.5” floppy disk drive
8
Card reader
9
Rear Panel
#
10
Description
#
Description
1
Six audio jacks (7.1 HD audio jack)
2
RJ-45 port
3
USB ports
4
1394 port
5
CRT/LCD port
6
Parallel port
7
Serial port
8
PS/2 keyboard
9
PS/2 mouse
10
Power cord port
11
SPDIF bracket
12
SPDIF port
13
Recovery switch holder
14
Lock handle
Chapter 1
Acer Empowering Technology
Acer’s innovative Empowering Technology makes it easy for you to access frequently used
functions and manage your new Acer notebook. It features the following handy utilities:
•
Acer eRecovery Management backs up and recovers data flexibly, reliably and completely.
•
Acer eDataSecurity Management protects data with passwords and advanced encryption
algorithms.
•
Acer ePerformance Management improves system performance by optimizing disk space, memory
and registry settings.
For more information, press the
key to launch the Empowering Technology menu, then click
on the appropriate utility and select the Help or Tutorial function.
Empowering Technology password
Before using Acer eRecovery Management, you must initialize the Empowering Technology
password. Right click on the Empowering Technology toolbar and select Password Setup to do
so. If you do not initialize the Empowering Technology password, you will be prompted to do so
when running Acer eRecovery Management for the first time.
Chapter 1
11
Acer eRecovery Management
Acer eRecovery Management is a powerful utility that does away with the need for recovery
disks provided by the manufacturer. The Acer eRecovery Management utility occupies space in a
hidden partition on your system’s HDD. User-created backups are stored on D:\ drive. Acer
eRecovery Management provides you with:
•
Password protection
•
Recovery of applications and drivers
•
Image/data backup:
•
•
Back up to HDD (set recovery point)
•
Back up to CD/DVD
Image/data recovery tools
•
Recovery from a hidden partition (factory defaults)
•
Recovery from the HDD (most recent user-defined recovery point)
•
Recovery from CD/DVD
For more information, please refer to Acer eRecovery Management.
Note: If your computer does not come with a Recovery CD or System CD, please use Acer eRecovery
Management’s System backup to optical disk feature to burn a backup image to CD or DVD. To
ensure the best results when you recover a system by using a CD or Acer eRecovery Management,
12
Chapter 1
detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer
ezDock.
Acer eDataSecurity Management
Acer eDataSecurity Management is a handy file encryption utility that protects your files from
being accessed by unauthorized persons. It is conveniently integrated with Windows explorer as
a shell extension for quick and easy data encryption/decryption and also supports on-the-fly file
encryption for MSN Messenger and Microsoft Outlook.
The Acer eDataSecurity Management setup wizard will prompt you for a supervisor password
and default encryption. This encryption will be used to encrypt files by default, or you can choose
to enter your won file-specific password when encrypting a file.
Note: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you
lose the password, the supervisor password is the only other key capable of decrypting the file. If you
lose both passwords, there will be no way to decrypt your encrypted file. Be sure to safeguard all
related passwords!
Chapter 1
13
14
Chapter 1
Acer ePerformance Management
Acer ePerformance Management is a system optimization tool that boosts the performance of
your Acer notebook. It provides and expresses optimization method to release unused memory
and disk space quickly. The user can also enable advanced options for full control over the
following option:
•
Memory optimization: to releases unused memory and check usage
•
Disk optimization: to remove unneeded items and files
•
Speed optimization: to improve the usability and performance of your Windows XP system
For more information, please refer to Acer eRecovery Management.
Note: If your computer does not come with a Recovery CD or System CD, please use Acer eRecovery
Management’s System backup to optical disk feature to burn a backup image to CD or DVD. To
ensure the best results when recovering your system using a CD or Acer eRecovery Management,
detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer
ezDock.
Chapter 1
15
Acer eRecovery
Acer eRecovery is a tool to quickly backup and restore the system. Users can create and save a
backup of the current system configuration to hard drive, CD, or DVD. Acer eRecovery consists of
the following functions:
1. Create backup
2. Restore from backup
3. Create factory default image CD
4. Re-install bundled software without CD
5. Change Acer eRecovery password
Create Backup
Users can create and save backup images to hard drive, CD, or DVD. Please follow the steps below
to create backup.
1. Boot to Windows XP.
2. Press <Alt> + <F10> to open the Acer eRecovery utility.
3. Enter the password to proceed. The default password is six zeros.
4. In the Acer eRecovery window, select Recovery settings and click Next.
5. In the Recovery settings window, select Backup snapshot image and click Next.
6. Select the backup method:
•
Use Backup to HDD to store the backup disc image on drive D:\
•
Backup to optical device to store the backup disc image on CD or DVD. This option is only
available on systems that include an optical disc burner.
7. After choosing the backup method, click Next.
Then follow the instruction on the screen to complete the process.
Restore from Backup
Users can restore backup previously created (as stated in the Create Backup section) from hard
drive, CD, or DVD. Please follow the steps below to restore from backup.
1. Boot to Windows XP.
2. Press <Alt> + <F10> to open the Acer eRecovery utility.
3. Enter the password to proceed. The default password is six zeros.
4. In the Acer eRecovery window, select Recovery actions and click Next.
5. Select the desired restore action and follow the instructions on screen to complete the restore process.
Create Factory Default Image CD
When the System CD and Recovery CD are not available, you can create them by using this
feature. Please follow the steps below to create factory default image CD.
1. Boot to Windows XP.
2. Press <Alt> + <F10> to open the Acer eRecovery utility.
3. Enter the password to proceed. The default password is six zeros.
4. In the Acer eRecovery window, select Recovery settings and click Next.
5. In the Recovery settings window, select Burn image to disc and click Next.
16
Chapter 1
6. In the Burn image to disc image, select Factory default image and click Next.
7. Follow the instruction s on screen to complete the process.
Re-install Bundled Software without CD
Acer eRecovery stores pre-loaded software internally for easy driver and application reinstallation.
1. Boot Windows XP.
2. Press <Alt> + <F10> to open the Acer eRecovery Utility.
3. Enter the password to proceed. The default password is six zeros.
4. In the Acer eRecovery window, select Recovery actions and Next.
5. In the Recovery settings window, select Re-install applications / drivers and click Next.
6. Select the desired driver / application and follow the instructions on screen to re-install.
After the first launch, Acer eRecovery prepared all the needed software and may take few
seconds to bring up the software content window.
Change Password
Acer eRecovery and Acer disc-to-disc recovery are protected by a password that can be changed
by users. Follow the steps below to change the password in Acer eRecovery.
1. Boot to Window XP.
2. Press <Alt> + <F10> to open the Acer eRecovery utility.
3. Enter the password to proceed. The default password is six zero.
4. In the Acer eRecovery window, select Recovery settings and click Next.
5. In the Recovery settings window, select Password: Change Acer eRecovery password and click
Next.
Follow the instructions on screen to complete the process.
Chapter 1
17
Acer Disc-to-Disc Recovery
Restore without a Recovery CD
This recovery process helps you restore the C:\ drive with the original software content that is
installed when you purchase your system. Follow the steps below to rebuild your C:\ drive.
Note: The C:\ drive will be reformatted and all data will be erased. It is important to back up all data
files before you use this option.
1. Restart the system.
2. While the Acer logo comes out, press <Alt> + <F10> to enter the recovery process.
3. The message The system has password protection. Please enter 000000: will be displayed.
4. Enter six zeros and continue.
5. The Acer Recovery main page appears.
6. Use the arrow keys to scroll through the items (operating system versions) and press <Enter> to select.
Multilingual Operating System Installation
Follow the instructions to choose the operating system and language you prefer when you first
power on the system.
1. Turn on the system.
2. Acer’s multilingual operating system selection menu will pop up automatically.
3. Use the arrow keys to scroll to the language version you want. Press <Enter> to confirm your selection.
4. The operating system and language you choose now will be the only option for future recovery
operations.
5. The system will install the operating system and language you choose.
18
Chapter 1
Hardware Specification and Configuration
Processor
Item
Specification
Type
Intel Prescott 775 / Smithfield / Cedar Mill / Presler / Conroe
Feature
• FSB: 533/800/1066MHz
• Socket type: Intel socket T LGA 775-pin
• HyperThreading Technology and FSB Dynamic Bus Inversion (DBI)
support
• 36-bit host bus addressing support, allowing the CPU to access the entire
GMCH memory address space
System Main Chipset
Item
Specification
Core logic
Intel G965 + Intel ICH8DH
Super I/O controller
ITE IT8718DX with hardware monitor
LAN controller
Intel 82566
Memory controller
Intel 965G
1394 controller
TI TSB43AB23PDTG4
Serial ATA
Six pendent SATA2 controller embedded in ICH8 each
supporting two devices
Audio subsystem controller
Realtek ALC888 (high definition audio)
VGA controller
Intel G965
North Bridge
Item
Specification
General
information
North bridge Broadwater is a Graphics Memory Controller Hub (GMCH)
designed for use with a LGA 775 (Land Grid Array) socket T processor. The
GMCH provides the CPU interface, DDR2 interface, PCI Express interface,
DMI (Direct Media Interface) and integrated graphics with display
interfaces. It communicates with the I/O Controller Hub (ICH8) over DMI
(Direct Media Interface).
Feature
• 1210 ball FC-BGA package
• Single processor support with 533/800/1066MHz data transfer rate
• Min. 128 MB memory capacity, assuming single channel mode by using
256MB technology
• Max. 8GB memory capacity in dual channel interleaved mode by using
1GB technology
• DMI 1.0 support
• PCI Express x16 graphics interface
• One 16-lane PCI Express port intended for graphics attach, fully
compliant to the PCI Express Base Specification revision 1.0a
Chapter 1
19
South Bridge
Item
Specification
General
Information
The Intel ICH8 is the other main component of the Intel Broadwater
chipset that integrates many I/O functions and provides the I/O subsystem
with access to the rest of the platform.
Feature
•
•
•
•
•
•
•
•
•
•
•
•
•
609-pin BGA package
Direct Media Interface (DMI) to the GMCH
PCI Express specification, revision1.0 compliant
Four PCI Express Root ports support
PCI local bus specification, revision 2.3 compliant with support for
33MHz PCI operations (seven PCI Request/Grant pairs support)
ACPI power management logic support
Enhanced DMA controller, interrupt controller, and timer functions
Integrated Serial ATA host controller with independent DMA operation
on four ports and AHCI support
USB host interface with support for eight USB ports; four UHCI host
controllers; one EHCI high speed USB 2.0 host controller
System Management Bus (SMBus) specification, version 2.0 with
additional support for I2C devices
Azalia specification support
Low pin count (LPC) interface support
I/O APIC 2.0
System Clock
Item
20
Specification
General
information
All clocks are generated by G965 and CK505.
Clock
synthesizer
•
•
•
•
•
•
•
•
•
•
•
Host: 133/200/266MHz (system bus 533/800/1066MHz)
Memory system (DDR2): 533/667/800MHz
PCI: 33MHz
PCI Express: 100MHz
DMI: 100MHz
USB: 48MHz
1394: 33MHz
SIO: 33MHz
ICH8: 14.318, 33, 48, and 100MHz
RTC: 32.768KHz
LAN: 25MHz
Chapter 1
System Memory
Item
Feature
Specification
• The GMCH system memory controller directly supports one or two
channels of memory (each channel consisting of 64 data lines).
• DDRII memory 533/667/800MHz support
• I/O voltage of 1.8V for DDRII
• Only unbuffered DIMMs support
• Max. memory bandwidth of 6.4GB/s in single channel or dual channel
asymmetric mode, or 12.8GB/s in dual channel interleaved mode
assuming DDRII 800MHz
• Four banks for all DDRII devices up to 512MB density support, eight
banks for 1GB DDRII devices
• Using 256MB technology, min. 128MB memory capacity, assuming single
channel mode
• Using 1GB technology dual channel interleaved mode, max. 8GB
memory capacity
• Max. 8GB DRAM address decode space
• Up to 32 simultaneous open pages per channel support (assuming four
banks of eight bank devices)
• Improved flexible memory architecture
Super I/O
Item
Description
Chip
ITE IT8718DX
Feature
•
•
•
•
•
Meets LPC specification 1.0
PS/2 keyboard and PS/2 mouse support
Up to four 3.5” disk drives support
Two serial ports, one EPP/ECP parallel port support
Three fans support (including fan speed control, speed monitoring
inputs)
• IrDA 1.0 SIR protocol with maximum baud rate up to 115.2K bps
• Hardware monitor support
USB Interface
Item
Description
Chip
ICH8DH
Feature
•
•
•
•
Chapter 1
Eight USB 2.0 ports support
Dual stack with RJ-45 back panel connector
Dual stack with 1394 connector in rear side
Two header supporting two USB ports for front panel cabling
21
Audio Interface
Item
Description
Chip
Realtek ALC888 (high definition audio)
Feature
• 48-pin LQFP green package
• High performance DACs with 95dB SNR (A-Weighting), ADCs with 85dB
SNR (A-Weighting)
• Meets performance requirements for audio on PC2001 systems and
Microsoft WLP 2.x
• Ten DAC channels 16/20/24bit PCM format support for 7.1 sound
playback, plus two channels of independent stereo sound output
(multiple streaming) through the front panel output
• Two stereo ADCs 16/20/24bit PCM format support, one for stereo
microphone, one for legacy mixer recording
• All DACs 44.1/48/96/192KHz sample rate support
• 16/20/24bit S/PDIF out supports 44.1/48/96/192KHz sample rate.
• 16/20/24bit S/PDIF in supports 44.1/48/96KHz sample rate.
• Up to four channels of microphone array input are supported for AEC/BF
application.
• High-quality analog differential CD input
• External PCBEEP input and built-in digital BEEP generator
• Reserve analog mixer architecture for backward compatibility with
AC’97
• Wide range (-80dB ~ +42dB) volume control with 1.5dB resolution of
analog to analog mixer gain
• Two GPIOs (General Purpose Input/Output) for customized applications
• Digital power support: 3.3V
• Analog power support: 3.5V ~ 5.25V
• Enhanced S/PDIF in circuitry ensures compatibility with consumer DVD
players.
• Pin compatible with the ALC880 and ALC882
1394 Interface
Item
Description
Chip
TSB43AB23PDTG
Feature
• Compliant with the IEEE 1394-1995 Release 1.0 and support IEEE 1394a
P2000 specifications with full 1394a P2000
• Compliant with the PCI V2.2 specification and card bus interfaces
support
• Three 1394a ports enable connections at 100/200/400Mbps
• Equipped with an OHCI compliant programming interface and I2C
EEPROMs or four-wire serial ROMs
22
Chapter 1
LAN Interface
Item
Description
Chip
Intel 82566
Feature
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
81-pin, 1.0 mm pitch, 10 mm x 10 mm FCMMAP (BGA) package
IEEE 802.3ab compliant
Robust end to end connections over various cable length
Full duplex at 10/100/1000Mbps and half duplex at 10 or 100Mbps
IEEE 802.3ab auto-negotiation with next page support
10/100 downshift: automatic link speed adjustment with poor quality
cable
Automatic MDI crossover
Advanced cable diagnostics
Footprint compatible with 82562V devices for a single-board dual design
(Gigabit and 10/100)
LCI interface for a very low power 10/100 link
Gigabit LAN connect interface: low pin count, high speed interface with
special low power idle modes and allows PHY placement proximity to I/O
back panel
Three LED outputs
Clock supplied to MAC
Full chip power down: lowest power state support
Power consumption less than 1.16W
Hardware Monitor Function
Item
Feature
Chapter 1
Description
• Smart fan control system, Thermal Cruise and Speed Cruise support
• Six VID input pins for CPU Vcore identification
• Two thermal inputs from optionally remote thermistors or 2N3904
transistors or Pentium 4 thermal diode output
• Four external voltage detect inputs
• Three intrinsic voltage monitoring (typical for Vbat, +5VSB, +5CC)
• Two fan speed monitoring inputs
• Two fan speed control (DC analog output)
• WATCHDOG comparison of all monitored items
• Overheat indication output
• Issue SMI#, IRQ, OVT# to activate system protection
23
BIOS ROM
Item
Description
Type
SST 39VF080
Package
40-pin TSOP
Block Size
64KB per block
Supply current
Active current: 15mA (typical)
Standby current: 4uA (typical)
Remark
The 32-pin PLCC package 1MB Flash ROM SST 39VF080 is used for BIOS,
keyboard encoder and power controller codes. It occupies system memory
area E0000-FFFFF. After posting system, the shadow RAM function will be
enabled.
BIOS
Item
Description
BIOS code
programmer
Phoenix Award
Version
Phoenix BIOS 6.00 PG
Feature
• ROM type: flash ROM
• ROM size: 4MB
• Protocol supported: PCIX 1.0, PCI 2.2, APM 1.2, VESA/DPMS (VBE/PM
V1.1), SMBIOS 2.3, E-IDE 1.1, ACPI 1.0b, ESCD 1.03, PnP 1.0a, Bootable
CD-ROM 1.0
• Boot from CD-ROM feature: yes
• LS-120 FDD drive support: yes
• BIOS boot block feature: yes
Note: The BIOS can be overwritten/upgraded by using the flash utility.
BIOS Hotkey List
Hotkey
DEL
Description
To enter BIOS Setup Utility: press the DEL key while the system is booting
to enter BIOS Setup Utility.
Environment Requirements
Item
Specification
Temperature
Operating
+5OC ~ +35OC
Non-operating
-20OC ~ +60OC (storage packed), -10OC ~ +60OC (unpacked)
Humidity
Operating
15% to 80% RH, non-condensing
Non-operating
10% to 90% RH, non-condensing at 40oC
Vibration
24
Operating
5 ~ 500Hz, 2.20g RMS random, 10 minutes per axis in all three axes
Non-operating
5 ~ 500Hz, 1.09g RMS random, one hour per axis in all three axes
Chapter 1
Power Management Function (ACPI Support Function)
Device Standby Mode
•
Independent power management timer for hard disk drive devices (zero to 15 minutes, time step =
one minute).
•
Hard disk drive goes into Standby mode (for ATA standard interface).
•
Disable V-sync to control the VESA DPMS monitor.
•
Resume method: device activated (keyboard for DOS, keyboard & mouse for Windows).
•
Resume recovery time: three to five seconds.
Global Standby Mode
•
Global power management timer (two to 120 minutes, time step = 10 minutes).
•
Hard disk drive goes into Standby mode (for ATA standard interface).
•
Disable H-sync and V-sync signals to control the VESA DPMS monitor.
•
Resume method: return to original state by pushing external switch button, modem ring in, keyboard
and mouse for APM mode.
•
Resume recovery time: seven to 10 seconds.
Suspend Mode
•
Independent power management timer (two to 120 minutes, time step = 10 minutes) or pushing
external switch button.
•
CPU goes into SMM.
•
CPU asserts STPCLK# and goes into the Stop Grant state.
•
LED on the panel turns amber color.
•
Hard disk drive goes into SLEEP mode (for ATA standard interface).
•
Disable H-sync and V-sync signals to control the VESA DPMS monitor.
•
Ultra I/O and VGA chip go into power saving mode.
•
Resume method: return to original state by pushing external switch button, modem ring in, keyboard
and mouse for APM mode.
•
Return to original state by pushing external switch button, modem ring in and USB keyboard for ACPI
mode.
ACPI
•
ACPI specification 1.0b
•
S0, S1, S3 and S5 sleep state support
•
Onboard device power management support
•
Onboard device configuration support
Chapter 1
25
Chapter 2
Setup Utility
About the Setup Utility
The computer uses the Phoenix Award BIOS (Basic Input and Output System) with support for
Windows Plug and Play. The CMOS chip on the main board contains the ROM setup instructions
for configuring the main board BIOS.
The BIOS Setup Utility displays the system’s configuration status and provides you with options to
set system parameters. The parameters are stored in Battery-backed-up CMOS RAM that saves
this information when the power is turned off. When the system is turned back on, the system is
configured with the values you have stored in CMOS.The BIOS Setup Utility enables you to
configure:
•
Hard drives, diskette drives and peripherals
•
Video display type and display options
•
Password protection from unauthorized use
•
Power management features
The settings made in the Setup Utility affect how the computer performs. Before using the Setup
Utility, ensure that you understand the Setup Utility options. This Setup Utility should be used:
•
when changing the system configuration
•
when a configuration error is detected and you are prompted to make changes to the Setup Utility
•
when trying to resolve IRQ conflicts
•
when making changes to the Power Management configuration
•
when changing the password or making other changes to the Security Setup
Control Keys
Item
Description
IKLJ
Move to the item you want to select
ENTER
Select the item you want or enter the sub-menu
ESC
Retreat from the current page
Pg Up
Increase the numeric value or make changes
Pg Dn
Decrease the numeric value or make changes
F1
General help
F5
Restore the previous CMOS value from CMOS
F7
Load the factory default setting
F10
Save all the CMOS changes
Exit
Leave the Setup Utility
Chapter 2
26
Entering the Setup Utility
Power on the computer and the system will start POST (Power On Self Test). When the message
Press DEL to enter SETUP appear on the screen, press the key DEL to enter the setup menu.
Once you enter the Phoenix Award BIOS CMOS Setup Utility, the main menu will appear on the
screen. Use arrow keys to select the item you want and press ENTER to make the setting or enter
the sub-menu.
27
Chapter 2
Product Information
This page displays product information about your system. You can press ESC to return to the
main menu setting page.
Chapter 2
28
Standard CMOS Features
Date and Time
The Date and Time items show the current date and time set on the computer. If you are running
a Windows OS, these items are automatically updated whenever you make changes to the
Windows Date and Time Properties utility.
SATA Devices
This main board features four SATA connectors supporting four SATA drives. SATA refers to Serial
ATA (Advanced Technology Attachment), the standard interface for the IDE hard drives which are
currently used in most PCs.
Drive A
This item will identify the type of floppy disk drive A that has been installed.
Halt On
This item determines whether the system stops or not if an error occurs during system boot-up.
At defaults All, But Keyboard, the boot will be interrupted for all errors except a keyboard
error.
Base Memory, Extended Memory, and Total Memory
These items are automatically detected by the system at start-up time. You can not make changes
to these fields.
29
Chapter 2
Advanced BIOS Features
Chapter 2
30
CPU Features
Scroll to this item and press ENTER to enter the sub-menu.
31
Chapter 2
Hard Disk Boot Priority
Scroll to this item and press ENTER to enter the sub-menu on next page.
Virus Warning
This item enables or disables the boot sector virus protection.
Quick Power On Self Test
You can enable this item to shorten the POST and have your system startup faster. You might like
to enable this item after you are confident that your system hardware is operating smoothly.
First / Second / Third Boot Device
Use this three items to select the priority and order of the devices that your system searches for
an operating system when the system is powering on.
Boot Other Device
When it is enabled, the system searches all other possible locations for an operating system. If it
fails to find on in the devices specified under the first, second, and third boot devices.
Boot Up NumLock Status
This item defines if the keyboard NumLock key is active when your system is booted.
Chapter 2
32
Gate A20 Option
This item defines how the system handles legacy software that was written for an earlier
generation of processors. Set this item for the default value.
Security Option
If you have installed password protection, this item defines if the password is required at system
start up, or if it is only required when a user tries to enter the Setup Utility.
APIC Mode
This item allows you to enable or disable the APIC (Advanced Programmable Interrupt Controller)
mode. APIC provides symmetric multi-processing (SMP) for systems.
MPS Version Control For OS
This item specifies which version of MPS (Multi-Processor Specification) this main board will use.
Set this item for its default setting.
Silent Boot
This item enables or disables the Silent Boot function.
Configuration Table
This item enables or disables the Configuration Table in BIOS setting.
33
Chapter 2
Advanced Chipset Features
These items define critical timing parameters of the main board. You should set these items for
their default values unless you are very familiar with the technical specification of your system
hardware. If you change the values incorrectly, you may introduce fatal errors or recurring
instability into your system.
PEG / OnChip VGA Control
This item allows you to choose the primary display card.
OnChip Frame Buffer Size
This allows you to set the VGA frame buffer size.
DVMT Mode
DVMT is Dynamic Video Memory Technology. This item helps you select video mode.
Chapter 2
34
Integrated Peripherals
35
Chapter 2
OnChip IDE Device
Scroll to this item and press ENTER to enter the sub-menu shown as below.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your
IDE hard drive supports block mode, select Enabled for automatic detection of the optimal
number of block read/write per sector the drive can support.
IDE DMA Transfer Access
This item allows you to enable the transfer access of the IDE DMA.
On-Chip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE interface with support for two IDE channels.
Select Enabled to activate each channel separately.
IDE Primary/Secondary Master/Slave PIO
Each IDE channel supports a master device and a slave device. These four items let you assign
which kind of PIO (Programmed Input/Output) is used by IDE devices. Choose Auto to let the
system auto detect which PIO mode is optimal, or select a PIO mode from zero to four.
IDE Primary/Secondary Master/Slave UltraDMA
This main board supports UltraDMA technology, which provides faster access to IDE devices. If
you install a device that supports UltraDMA, you can change the item on this list to Auto. You
Chapter 2
36
may have to install the UltraDMA driver supplied with this main board in order to use an
UltraDMA device.
Onboard Device
Scroll to this item and press Enter to enter the sub-menu shown as below.
USB Controller
You can enable or disable the onboard USB controller. We recommend users to keep the default
value. Disabling it might cause the USB devices not to work properly.
USB 2.0 Support
This item enables or disables the onboard USB 2.0.
USB Keyboard Support
You can enable this item if you want to use a keyboard connected through the USB port in a
legacy operating system (such as DOS) that does not support Plug and Play.
USB Mouse Support
You can enable this item if you want to use a mouse connected through the USB port in a legacy
operating system (such as DOS) that does not support Plug and Play.
Onboard 1394
This item allows users to enable or disable the onboard 1394 function.
37
Chapter 2
Onboard LAN Controller
This item allows users to enable or disable the onboard LAN Controller function.
Onboard LAN Boot ROM
This item allows you to enable or disable the onboard LAN Boot ROM function.
Super I/O Device
Scroll to this item and press ENTER to enter the sub-menu shown as below.
Onboard FDC Controller
If your system has a floppy disk controller (FDC) installed on the system board and you want to
use it, you can select Enabled. If you install an add-in FDC or the system has no floppy drive, select
Disabled in this field.
Onboard Serial Port 1
This option is used to assign the I/O address and interrupt request (IRQ) for onboard serial port 1
(COM1).
Onboard Serial Port 2
This option is used to assign the I/O address and interrupt request (IRQ) for onboard serial port 2
(COM2).
Chapter 2
38
Onboard Parallel Port
This option is used to assign the I/O address and interrupt request (IRQ) for the onboard parallel
port.
Parallel Port Mode
This item enables you to set the data transfer protocol for your parallel port. There are four
options: SPP (Standard Parallel Port), EPP (Enhanced Parallel Port), ECP (Extended Capabilities
Port), and ECP + EPP. SPP allows data output only. ECP and EPP are bi-directional modes, allowing
both data input and output. ECP and EPP modes are only supported with EPP- and ECP-aware
peripherals.
ECP Mode Use DMA
When the onboard parallel port is set for ECP mode, the parallel port can use DMA3 or DMA1.
39
Chapter 2
Power Management Setup
The system has various power-saving modes including powering down the hard disk, turning off
the video, suspending to RAM, and software power down that allows the system to be
automatically resumed by certain events.
The power-saving modes can be controlled by time-outs. If the system is inactive for a while, the
time-outs begin counting. If the inactivity continues so that the time-out period elapses, the
system enters a power-saving mode. If any item in the list of Reload Global Timer Events is
Enabled, then any activity on that item will reset the time-out counters to zero.
If the system is suspended or has been powered down by software, it can be resumed by a wake
up call that is generated by incoming traffic to a modern, a LAN card, a PCI card, or a fixed alarm
on the system real-time clock.
ACPI Function
This item allows users to enable or disable the ACPI power management function.
ACPI Suspend Type
You can use this item to define how your system suspends.
Run VGA BIOS if S3 Resume
This item allows the system to initialize the VGA BIOS from S3 (Suspend to RAM) sleep state.
Chapter 2
40
Soft-Off by PWR-BTTN
Under ACPI (Advanced Configuration and Power Management Interface) you can create a
software power down. In a software power down, the system can be resumed by Wake Up
Alarms. This item lets you install a software power down that is controlled by the power button
on your system. If the item is set for Instant-Off, then the power button causes a software power
down. If the item is set for Delay four Sec., then you have to hold the power button down for
four seconds to cause a software power down.
Energy Lake Function
This item enables or disables the Energy Lake Function.
Wake Up On LAN
When it is Enabled, you can remotely wake up a PC in Soft-Off condition via a LAN card that
supports the wake up function.
Power On by Ring
An input signal on the serial Ring indicator (RI) line (in other words, an incoming call on the
modem) awakens the system from soft off state.
USB KB/MS Wake-up S1/S3/S4
This option allows the activity of the USB devices (keyboard and mouse) to wake up the system
from S1/S3/S4 status.
PS2 KB/MS Wake-up S3
This option allows the activity of the PS2 keyboard and mouse to wake up the system from S3
status.
Resume by Alarm
When it is Enabled, additional fields become available and you can set the date, hour, minute
and second to turn on your system. When it is set for zero in the column of date, the alarm will
power on your system every day at the specified time.
41
Chapter 2
PnP/PCI Configurations
It configures how PnP (Plug and Play) and PCI expansion cards operate in your system. Both the
ISA and PCI buses on the main board use system IRQs (interrupt requests) and DMAs (direct
memory access). You must set up the IRQ and DMA assignments correctly through the PnP/PCI
Configurations Setup Utility for the main board to work properly. Selecting PnP/PCI
Configurations on the main program screen displays the menu below.
PCI/VGA Palette Snoop
This item is designed to overcome problems that can be caused by some non-standard VGA cards.
This board includes a built-in VGA system that does not require palette snooping so you must
leave this item disabled.
Maximum Payload Size
This item specifies the maximum TLP payload size for the PCE Express devices.
Chapter 2
42
PC Health Status
On the main board that supports hardware monitoring, you can monitor the parameters of
critical voltage, temperature and fan speed.
Advanced Fan Control
This item incorporates linear control metrics to provide optimal cooling. Under normal condition,
Advanced Fan Control keeps the fan speed low, minimizing acoustic noise. When the load
increases, Advanced Fan Control increases the fan speed to provide optimal cooling.
43
Chapter 2
Frequency Control
It enables you to set the clock speed and system bus for your system. The clock speed and system
bus are determined by the processor you have installed in your system.
CPU Clock Ratio
This item allow you to adjust the CPU clock to 200MHz. You can key in the number within the
range to make a precise and ideal adjustment.
Auto Detect PCI Clk
When it is enabled, BIOS will disable the clock signal of free DIMM and PCI slots.
Spread Spectrum
If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference)
generated by the system.
Chapter 2
44
Load Default Settings
This option opens a dialog box that lets you install optimized defaults for all appropriate items in
the Setup Utility. Press OK and then ENTER to install the defaults. Press CANCEL and then ENTER
to not install the defaults. If you only want to install setup defaults for a specific option, select
and display that option, and then press F9.
Set Supervisor/User Password
When this function is selected, the following message appears at the center of the screen to assist
you in creating a password.
Enter Password
Type the password, up to eight characters, and press ENTER. The password typed now will clear
any previously entered password from CMOS memory. You will be asked to confirm the
password. Type the password again and press ENTER. You can press ESC to abort the selection.
To disable password, just press ENTER when you are prompted to enter password. A message will
confirm the password being disabled. Once the password is disabled, the system will boot and
you can enter BIOS Setup freely.
Password Disabled
If you have selected System in Security Option of BIOS Features Setup menu, you will be
prompted for the password every time the system reboots or any time you try to enter BIOS
Setup.
If you have selected Setup in Security Option of BIOS Features Setup menu, you will be
prompted for the password only when you enter BIOS Setup.
Supervisor Password has higher priority than User Password. You can use Supervisor Password
when booting the system or entering BIOS Setup to modify all settings. Also you can use User
Password when booting the system or entering BIOS Setup but can not modify any setting if
Supervisor Password is enabled.
Save and Exit Setup
You can highlight this item and press ENTER to save the changes that you have made in the
Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears, press OK to
save and exit, or press CANCEL to return to the main menu.
Exit without Saving
You can highlight this item and press ENTER to discard any changes that you have made in the
Setup Utility and exit the Setup Utility. When the Exit without Saving dialog box appears, press
OK to discard changes and exit, or press CANCEL to return to the main menu.
NOTE: If you have made settings that you do not want to save, choose the Discard Changes and Exit
and press OK to discard any changes you have made.
45
Chapter 2
Chapter 3
Machine Disassembly and Replacement
General Information
This chapter contains step-by-step procedures on how to disassemble the Aspire E700 for
maintenance and troubleshooting.
To disassemble the notebook, you need the tools below:
•
Wrist ground strap and conductive mat for preventing electrostatic discharge
•
Small Philips screw driver
•
Flat head screw driver
•
Hexagonal driver
•
Tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
Before You Begin
Before proceeding with the disassembly procedure, you have to make sure that:
•
The system and all peripherals are powered off.
•
The AC adaptor and all power and signal cables from the system are unplugged.
•
The battery pack is removed.
NOTE: There are several types of screws used to secure the main unit. The screws vary in length. Please
refer to the screws table after the flowchart. Group the same type of screws together during service
disassembling. Please also remember the screw location for each screw type. If you fasten the screws
on the wrong location, the long screws may cause irrecoverable damage to the main board.
Chapter 3
46
Aspire E700 Disassembly Procedure
1. Place the system unit on a flat, steady and nonskid surface.
2. Release the lock handle then slide the left cover out.
3. Detach the VGA card.
4. Detach the modem card.
5. Disconnect the IR cable.
6. Disconnect the front bezel LED cable.
47
Chapter 3
7. Disconnect the SPDIF cable.
8. Disconnect the audio cable.
9. Disconnect the USB cables.
10. Disconnect the PA and the PD cables linked to the main board.
Chapter 3
48
11. Disconnect the P1 power supply cable and FDD data cable.
12. Disconnect the ODD power cable and the ODD data cable.
13. Disconnect the HDD power cable and the HDD data cable.
49
Chapter 3
14. Slide the HDD holder as shown below then take the HDD out from the chassis.
15. Release the three latches holding the front panel then remove the front panel.
16. Slide the ODD holder as shown below then take the ODD out from the chassis.
Chapter 3
50
17. Detach the card reader.
18. Detach the CPU cooler from the main board.
19. Pull the two latches at the same time to release the memory. Repeat this step to remove another
memory.
20. Release the four screws fastening the system fan then remove the system fan.
21. Push and release the CPU latch then detach the CPU.
51
Chapter 3
22. Release the screws marked below then remove the main board.
23. Release the four screws marked below then remove the system power supply.
Chapter 3
52
Chapter 4
Troubleshooting
Please refer to generic troubleshooting guide in the service guide database for information with
respect to following items:
•
Power-On Self-Test (POST)
•
POST Check Points
•
POST Error Messages List
•
Error Symptoms List
Chapter 4
53
Chapter 5
Jumper and Connector Location
Main Board Placement
Chapter 5
54
55
Item
Description
Item
Description
CPU_FAN1
CPU fan header
BIOS_SEL1
SPI & FWH BIOS select
COM2
COM header 2
PWR2
Four-pin power connector
J11
Acer special requirement
KB/MS1
Keyboard & mouse PS2
port
J10
Acer special requirement
COM1
COM port
PWR1
24-pin power connector
PRT
Printer port
FLOPPY1
Floppy connector 1
VGA
VGA port
SYS_FAN1_1
System fan header 1_1
(three-pin)
1394_USB1
1394 and USB*2 port
CLR_CMOS
Clear CMOS
NIC_USB
LAN and USB*2 port
OBR
One button recovery
Audio
Audio port
INTR1
Chassis intruder
PCI-E1
PCI-Express x16 connector
FP1
Front panel switch/LED
BAT1
Battery connector
TPM
Trusted platform module
interface
PCI-E2
PCI-Express x1 connector
SATA_5
SATA data transfer
connector 5
F_1394
Front 1394 header
SATA_6
SATA data transfer
connector 6
PCI1, PCI2
PCI connector
SATA_3
SATA data transfer
connector 3
U25
FWH BIOS socket
SATA_4
SATA data transfer
connector 4
U19
ICH8 series south bridge
SATA_1
SATA data transfer
connector 1
U13
965 series north bridge
SATA_2
SATA data transfer
connector 2
U10
LGA 775 CPU socket
F_USB3
Front panel USB header 3
DIMM1,
DIMM2,
DIMM3,
DIMM4
DDR2 memory connector
F_USB2
Front panel USB header 2
IR
Infrared function header
F_USB1
Front panel USB header 1
FLOPPY1
Floppy connector
F_AUDIO1
Audio Aux Input
BUZ1
Buzzer
Chapter 5
Introduction of Connectors and Headers
System Board Jumper Setting
Features
Default Setting
Remark (color and other)
Intruder pin (1*2) & default
setting
No active
Short will have the warning
message The case has been
opened, press F1 to continue.
BIOS_SEL1 (1*2) & default
setting
Enable SPI
Clear CMOS (1*3) & default
setting
2-3: normal (default)
OBR (1*2) & default setting
No active
System Board Header Setting
Front Panel
FP1
1
3
5
7
9
11
13
Orange1
Green2
Orange3
Green4
Blue5
Red6
Blue7
Red8
Orange13 Green14
Header_2X7_K10
Chapter 5
Pin Definition
Description
1
5V_SYS
Hard disk LED pull-up (330 ohm) to
5V_SYS
2
GPIO_GRN_HDR_R
Pull-up (330 ohm) to 5V_SB_SYS and
connect To to SIO GPIO
3
HDD_LED_R
Hard disk active LED
4
GPIO_YLW_HDR_R
Pull-up (330 ohm) to 5V_SB_SYS and
connect to SIO GPIO
5
GND
Reset button
6
PSIN
Power button
7
ICH_SYS_RSTJ
ICH_SYS_RSTJ
8
GND
Ground
9
5V_SYS
5V_SYS
10
Key
Key
11
NC
Reserved
12
GND
Ground
13
NC
Reserved
14
LAN_ACTJ
LAN active LED
2
4
6
8
Black9
Orange11 Green12
#
12
14
56
Front USB
#
Pin Definition
Description
1
VREG_FP_USBPWR0
Front panel USB power (ports 0 & 1)
2
VREG_FP_USBPWR0
Front panel USB power (ports 0 & 1)
3
USB_FP_P0-
Front panel USB port 0 negative signal
4
USB_FP_P1-
Front panel USB port 1 negative signal
5
USB_FP_P0+
Front panel USB port 0 positive signal
6
USB_FP_P1+
Front panel USB port 1 positive signal
7
GND
Ground
8
GND
Ground
9
Key
Key
10
USB_FP_OC0
Front panel USB over current signal (port 0
& 1)
#
Pin Definition
Description
1
AUD_MIC
Front panel microphone input signal
2
AUD_GND
Ground used by analog audio circuits
3
AUD_MIC_BIAS
Microphone power
4
AUD_VCC
Filtered +5V used by analog audio circuits
5
AUD_FPOUT_R
Right channel audio signal to front panel
6
AUD_RET_R
Right channel audio signal return from
front panel
7
HP_ON
RSVD for future use to control headphone
amplifier
8
Key
No pin
9
AUD_FPOUT_L
Left channel audio signal to front panel
10
AUD_RET_L
Left channel audio signal return from
front panel
Front Audio (AC’97)
57
Chapter 5
Front 1394
#
Signal Name
1
TPA+
2
TPA-
3
Ground
4
Ground
5
TPB+
6
TPB-
7
+12V (fused)
8
+12V (fused)
9
Key
10
Ground
#
Description
1
CD left channel
2
Ground
3
Ground
4
CD right channel
5
Key
#
Description
1
Ground
2
FANOUT
3
SIO FANSPD
4
Key
#
Description
1
Ground
2
FAN POWER 12V
3
SIO FANSPD
4
FANOUT
5
Key
AUX_IN
System Fan
CPU Fan
Chapter 5
58
Clear CMOS
#
Description
1
Ground
2
RTCRSTJ (Connect to ICH)
3
Connect to VCC_RTC
Pin 2-3: normal
Pin 1-2: clear CMOS
Intruder
#
Description
1
INTRUDERJ
2
Ground
#
Description
1
AGPIO1
2
Ground
J10
J11
#
Description
1
AGPIO2
2
Ground
One Button Recovery (OBR)
59
#
Description
1
ICH_GPIO8_PU
2
Ground
Chapter 5
TPM
#
Description
1
LCLK
2
GND
3
LFRAME#
4
KEY
5
LREST
6
NC_3
7
LAD3
8
LAD2
9
VDD
10
LAD1
11
LAD0
12
GND
13
NC_1
14
NC_4
15
NC_2
16
SERIRQ
17
GND
18
CLKRUN
19
LPCPD
20
NC_6
#
Description
1
COM_SER2_RLSD
2
COM_SER2_SIN
3
COM_SER2_SOUT
4
COM_SER2_DTR
5
Ground
6
COM_SER2_DSR
7
COM_SER2_RTS
8
COM_SER2_CTS
9
COM_SER2_RI
10
Key
CMO HEADER
Chapter 5
60
IR
61
#
Description
1
5V
2
IR_26
3
SIO_RSMRSTJ
4
RESETCONJ
5
IR_20
6
IR_27
7
IR_RE
8
IR_21
9
IR_RE
10
Key
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter offers the FRU (Field Replaceable Unit) list in global configuration of Aspire E700
desktop. Refer to this chapter whenever ordering the parts to repair or for RMA (Return
Merchandise Authorization).
Please note that when ordering FRU parts, you should check the most up-to-date information
available on your regional web or channel. For whatever reasons a part number is changed, it
will NOT be noted on the printed service guide. For Acer authorized service providers, your Acer
office may have a different part number code from those given in the FRU list of this printed
service guide. You MUST use the local FRU list provided by your regional Acer office to order FRU
parts for service.
Note: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose them properly, or follow the rules set by your regional Acer office on
how to return it.
Chapter 6
62
Exploded Diagram
63
Chapter 6
Item
Description
1
5.25” ROTATE COVER
2
A451 BEZEL
3
CD-ROM
4
FDD WITH PANEL
5
HDD-DISK
6
MOTHER BOARD
7
HDD-LOCK-SLIDE
8
FDD-LOCK-SLIDE
9
CDROM-LOCK-SLIDE
10
USB BOARD
11
USB BKT
12
RIGHT-SIDE
13
CHASSIS
14
POWER-SUPPLY
15
FAN
16
PCC-BKT
17
LEFT-SIDE
Chapter 6
64
Parts
PARTNAME
DESCRIPTION
ACER PART NO.
BOARD
DAUGHTER BOARD USB/AUDIO
USB BOARD
55.S46VF.001
MB FG965M FOR P4 LGA775 CPU INTEL
G965+ICH8DH DDR2 Gigabit LAN HD
codec W/I 1394 W/I CPU RM
FG965M
MB.S5909.002
"MB FG965M FOR P4 LGA775 CPU
INTEL G965+ICH8DH DDR2 Gigabit LAN
HD codec W/I 1394, CPU RM, I/O
SHIELDING (4 USB PORTS)"
FG965M
MB.S5909.001
"KYE CARD READER+1394+IR,
CR503U2, W/I HOUSING, W/I 1394
CABLE+USB CABLE"
CR503U2-5101
PZ.CR50J.001
"KYE CARD READER+1394+IR,
CR503U2, W/I HOUSING, W/I 1394
CABLE+USB CABLE"
CR503U2-5111
PZ.CR50J.003
LOGITECH WIRELESS BOARD
LOGITECH WIRELESS BOARD
RV.GPY01.005
LOGITECH WIRELESS RECEIVER
LOGITECH WIRELESS RECEIVER
RV.GPY01.006
POWER SWITCH/ HDD /LAN LED CABLE
POWER SWITCH/ HDD /LAN LED
CABLE
50.S55VF.001
HDD CABLE SATA_1
"SATA-HDD DATA CABLE, ROHS"
50.S46VF.001
SERIAL ATA DATA CABLE FOR ODD
SERIAL ATA DATA CABLE FOR ODD
50.P37VF.001
SERIAL ATA POWER CABLE FOR ODD
SERIAL ATA POWER CABLE
50.P37VF.002
USB CABLE
"USB CABLE (460MM) , ROHS"
50.S46VF.002
AUDIO CABLE
"AUDIO CABLE (560MM), ROHS"
50.S46VF.004
IDE FDD CABLE 34PIN
"FDD DATA CABLE, ROHS"
50.S46VF.007
SPDIF BOARD W/ CABLE
SPDIF BOARD W/ CABLE
55.S46VF.002
LED CABLE FOR THE LOGO
LED CABLE FOR THE LOGO
50.S46VF.005
IR CABLE
IR CABLE
50.S46VF.006
"FRONT BEZEL W/ POWER BUTTON,
5.25"" 3.5"" EMPTY COVER"
A451 BEZEL ASSY
60.S46VF.001
POWER BUTTON
POWER BUTTON
42.S46VF.001
ODD COVER 1 W/ HOLDER
A451 ODD-UPPER DOOR W/
HOLDER
42.S46VF.002
ODD COVER 2 W/ HOLDER
A451 ODD-LOWER DOOR W/
HOLDER
42.S46VF.003
TOP COVER ASSY
TOP COVER ASSY
60.S46VF.002
FRONT COVER WITH ACER LOGO
FRONT COVER WITH ACER LOGO
60.S46VF.003
"FILLER COVER FOR 3 1/2"" DEVICE"
"3.5"" FILLER PANEL"
42.S46VF.009
MAINBOARD
CARD READER
RF RECEIVER
CABLE
CASE/ COVER/ BRACKET ASSEMBLY
65
Chapter 6
PARTNAME
DESCRIPTION
ACER PART NO.
CHASSIS W/O SIDE DOOR W/O I/O
SHIELD H401
H401 CHASSIS W/O SIDE DOOR W/O
I/O SHIELD
60.S46VF.004
SIDE DOOR-LEFT
LEFT-BKT-DOOR (PAINTING )
60.S46VF.005
SIDE DOOR-RIGHT
RIGHT-BKT-DOOR (PAINTING)
60.S46VF.006
S-LOCK-HANDLE
S-LOCK-HANDLE
42.S46VF.004
ODD HOLDER ASSY
ODD HOLDER ASSY
42.S46VF.005
FDD HOLDER ASSY
FDD HOLDER ASSY
42.S46VF.006
HDD HOLDER ASSY
HDD HOLDER ASSY
42.S46VF.007
IO BRACKET HOLDER
PCI-BKT
42.S46VF.008
I/O BRACKET
COVER SLOT
33.S45VF.001
REAR I/O SHIELDING FOR FG965M MB
I/O SHIELDING
PZ.S5908.001
"PRONET PCI MODEM CARD HPI56M3F
W/ATX BKT, ROHS"
HPI56M3F
FX.56M03.003
MODEM CARD D-1156#A7A LITEON
D-1156I#/A7A
FX.15602.001
"PRONET WIRELESS PCI CARD WP61R
CHIP REALTEK RTL8185L W/ATX BTK,
ROHS"
WP61R
NI.61R08.002
WINTV-HVR1100 DVB-T PAL OXFORD
94500 REV C2A0 LF
WINTV-HVR-1100
TV.HAUDV.BT3
WINTV-HVR1110 DVB-T PAL OXFORD2
67559 REV B1B4
WINTV-HVR-1110
TV.HAUOX.BT2
ANALOGUE MULTI PAL / FM / HW
MPEG2 ENCODER / ATX BRACKET REV:
F089 LF
WINTV-PVR150MCE
TV.AMITY.HR1
HYBRID TV CARD ( WW. ANALOGUE /
DVB-T) / CABLES / FM ANTENNA
LR306N
TU.30605.005
"SP RADEON X1300 512MB HM
(ONBOARD 64MB) DDR(INFINEON) 32BITS VGA+TVO PAL W/ATX BKT,88AC94-0A-AC,ROHS"
88-AC94-0A-AC
54.X1300.H17
"SP RADEON X1300 512MB HM
(ONBOARD 64MB) DDR(INFINEON) 32BITS VGA+TVO NTSC W/ATX BKT,88AC94-0A-AC,ROHS"
88-AC94-0A-AC
54.X1300.H18
"SP RADEON X1300 512MB HM
(ONBOARD 64MB) DDR(INFINEON) 32BITS VGA+TVO PAL W/ATX BKT,88-AC-94-0A-AC,ROHS, REV 0.2"
88-AC94-0A-AC
54.X1300.H19
"SP RADEON X1300 512MB HM
(ONBOARD 64MB) DDR(INFINEON) 32BITS VGA+TVO NTSC W/ATX BKT,88AC94-0A-AC,ROHS, REV 0.2"
88-AC94-0A-AC
54.X1300.H20
"SAPPHIRE RADEON X1600 SE 256MB
128BIT DDR(INFINEON) VGA+TVO+DVII PAL W/ATX BKT ROHS, REV 0.1"
88-8C87-11-AC
54.X16SE.013
"SAPPHIRE RADEON X1600 SE 256MB
128BIT DDR(INFINEON) VGA+TVO+DVII NTSC W/ATX BKT ROHS, REV 0.1"
88-8C87-11-AC
54.X16SE.014
ADD-ON CARD
Chapter 6
66
PARTNAME
DESCRIPTION
ACER PART NO.
SAPPHIRE RADEON X1600 SE 256MB
128BIT DDR(INFINEON) VGA+TVO+DVII PAL W/ATX BKT ROHS
88-8C87-11-AC
54.X16SE.011
SAPPHIRE RADEON X1600 SE 256MB
128BIT DDR(INFINEON) VGA+TVO+DVII NTSC W/ATX BKT ROHS
88-8C87-11-AC
54.X16SE.012
"SP ATI RADEON X1650SE 512MB HM
ONBOARD 256M 64BIT DDR2(HYNIX)
VGA+TVO+DVI-I PAL W/ATX BKT, 889C92-0C-AC, ROHS"
88-9C92-0C-AC
54.X1650.S01
"SP ATI RADEON X1650SE 512MB HM
ONBOARD 256M 64BIT DDR2(HYNIX)
VGA+TVO+DVI-I NTSC W/ATX BKT, 889C92-0C-AC, ROHS"
88-9C92-0C-AC
54.X1650.S02
SHD-16S1S
KV.01604.009
GCC-H10N
KO.0520A.005
"16X DVD DUAL LAYER GSAH31N,LF,SATA"
GSA-H31N
KU.0160D.013
"16X DVD DUAL LAYER SHW-160S6S,
LF, SATA"
SHW-160S6S
KU.01604.009
CORE 2 DUO E6600 (2.4G 4M 1066FSB)
B2
HH80557PH0564M
KC.66001.DE0
CORE 2 DUO E6300 (1.86G 2M 1066FSB)
B2
HH80557PH0362M
KC.63001.DE0
DVD-ROM DRIVE
"16X DVD-ROM SHD-16S1S , LF , SATA"
COMBO MODULE
"52X COMBO , HLDS GCC-H10N , LF,
SATA"
DVD DUAL DRIVE
CPU/ PROCESSOR
PENTIUM D 945 (3.4G 2X2M 800FSB) C1
KC.DC001.945
PENTIUM D 940 (3.2G 2X2M 800FSB) C1
HH80553PG0884MH
KC.DC001.940
PENTIUM D 930 (3.0G 2X2M 800FSB) C1
HH80553PG0804MH
KC.DC001.930
PENTIUM D 915 (2.8G 2X2M 800FSB) C1
HH80553PG0724MN
KC.D0001.915
PENTIUM D 945 (3.4G 2X2M 800FSB) C1
945
KC.DC001.945
PENTIUM D 925 (3.0G 2X2M 800FSB) C1
925
KC.D0001.925
FOXCONN CPU COOLER
PKP249GB1U12 + PMD1208PKV1-A
"PKP249GB1U12 + PMD1208PKV1A P/N:B1411.F(8020+4P), 80*80*20
(REV5)"
HI.2490C.004
FOXCONN CPU COOLER
PKP367G01U12 + SUNON 9225
4200RPM FAN
PKP367G01U12 + SUNON 9225
4200RPM FAN
HI.3670C.001
"THERMALFLY CPU COOLER, V2.0,
ROHS"
P300L
HI.P300L.001
SYSTEM FAN KDE 1209/GP 92*92*25
(ROHS)
KDE1209PTV3
HI.S150F.002
ST3160812AS
KH.16001.018
FAN SINK
HARD DISK DRIVE
"160GB ST3160812AS W/NCQ, SATAII,
8MB, ROHS"
67
Chapter 6
PARTNAME
DESCRIPTION
ACER PART NO.
"200GB ST3200827AS W/NCQ, SATAII,
8MB, ROHS"
ST3200827AS
KH.20001.007
"250GB ST3250824AS W/NCQ, SATAII,
8MB, ROHS"
ST3250824AS
KH.25001.005
"300GB ST3300822AS W/NCQ, SATAII,
8M, ROHS"
ST3300822AS
KH.30001.008
"400GB ST3400833AS W/NCQ, SATAII,
8M, ROHS"
ST3400833AS
KH.40001.005
"200GB WD2000JS-22NCB1 W/NCQ,
SATAII, 8M, ROHS"
WD2000JS-22NCB1
KH.20008.019
"XL80III,250G,WD2500JS-22NCB1 W/
NCQ, SATAII, 8M, ROHS"
WD2500JS-22NCB1
KH.25008.015
"320GB HDT725032VLA380 SATAII
8M,ROHS"
HDT725032VLA380
KH.32007.001
"400GB HDT725040VLA380 SATAII
8M,ROHS"
HDT725040VLA380
KH.40007.006
USB KEYBOARD SK-9610 US VER.
104KS(WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.045
USB KEYBOARD SK-9610 T.CHINESE
VER. 104KS(WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.046
USB KEYBOARD SK-9610 S.CHINESE
104KS(WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.047
USB KEYBOARD SK-9610 INL US VER.
104KS(WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.048
USB KEYBOARD SK-9610 ARABIC VER.
104KS(WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.049
USB KEYBOARD SK-9610 THAI VER.
104KS(WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.050
USB KEYBOARD SK-9610 SPANISH VER.
105KS(WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.051
USB KEYBOARD SK-9610 PORTUGESE
VER. 105KS(WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.052
USB KEYBOARD SK-9610 CANADIAN/
FRENCH VER. 105KS(WITH EKEY VISTA)
ROHS
SK-9610
KB.9610B.053
USB KEYBOARD SK-9610 BRAZILIAN
VER. 107KS(WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.054
USB KEYBOARD SK-9610 JPNESE
109KS(WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.055
USB KEYBOARD SK-9610 GERMANY
VER. 105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.056
USB KEYBOARD SK-9610 ITALIAN VER.
105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.057
USB KEYBOARD SK-9610 FRENCH VER.
105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.058
USB KEYBOARD SK-9610 SWEDEN VER.
105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.059
USB KEYBOARD SK-9610 UK VER.
105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.060
KEYBOARD
Chapter 6
68
PARTNAME
69
DESCRIPTION
ACER PART NO.
USB KEYBOARD SK-9610 DUTCH VER.
105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.061
USB KEYBOARD SK-9610 SWISS VER.
105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.062
USB KEYBOARD SK-9610 BELGIUM VER.
105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.063
USB KEYBOARD SK-9610 ICELAND VER.
105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.064
USB KEYBOARD SK-9610 NORWEGIAN
VER. 105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.065
USB KEYBOARD SK-9610 HEBREW VER.
104KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.066
USB KEYBOARD SK-9610 POLISH VER.
105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.067
USB KEYBOARD SK-9610 SLOVENIAN
VER. 105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.068
USB KEYBOARD SK-9610 SLOVAKIAN
VER. 105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.069
USB KEYBOARD SK-9610 TURKEY QTYPE VER. 105KS (WITH EKEY VISTA)
ROHS
SK-9610
KB.9610B.070
USB KEYBOARD SK-9610 RUSSIAMVER.
104KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.071
USB KEYBOARD SK-9610 HUNGARIA
VER. 105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.072
USB KEYBOARD SK-9610 GREEK VER.
104KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.073
USB KEYBOARD SK-9610 DENMARK
VER. 105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.074
USB KEYBOARD SK-9610 CZECH VER.
104KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.075
USB KEYBOARD SK-9610 ROMANIAN
VER. 105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.9610B.076
USB KEYBOARD SK-9610 TURKEY FTYPE VER. 105KS (WITH EKEY VISTA)
ROHS
SK-9610
KB.9610B.077
USB KEYBOARD SK-9610
FRENCH+ARABIC 105KS (WITH EKEY
VISTA) ROHS
SK-9610
KB.9610B.078
USB KEYBOARD SK-9610 SPANISH
LATIN VER. 105KS(WITH EKEY VISTA)
ROHS
SK-9610
KB.9610B.079
USB KEYBOARD SK-9610 ITALIAN VER.
S1 105KS (WITH EKEY) ROHS
SK-9610
KB.USB0B.002
USB KEYBOARD SK-9610 ITALIAN VER.
S1 105KS (WITH EKEY VISTA) ROHS
SK-9610
KB.USB0B.001
USB KEYBOARD KU-0355 US VER.
104KS(WITH EKEY VISTA) ROHS
KU-0355
KB.KUS03.222
USB KEYBOARD KU-0355 T.CHINESE
VER. 104KS(WITH EKEY VISTA) ROHS
KU-0355
KB.KUS03.223
Chapter 6
PARTNAME
DESCRIPTION
ACER PART NO.
USB KEYBOARD KU-0355 S.CHINESE
104KS(WITH EKEY VISTA) ROHS
KU-0355
KB.KUS03.224
USB KEYBOARD KU-0355 INL US VER.
104KS(WITH EKEY VISTA) ROHS
KU-0355
KB.KUS03.225
USB KEYBOARD KU-0355 ARABIC VER.
104KS(WITH EKEY VISTA) ROHS
KU-0355
KB.KUS03.226
USB KEYBOARD KU-0355 THAI VER.
104KS(WITH EKEY VISTA) ROHS
KU-0355
KB.KUS03.227
USB KEYBOARD KU-0355 SPANISH VER.
105KS(WITH EKEY VISTA) ROHS
KU-0355
KB.KUS03.228
USB KEYBOARD KU-0355 CANADIAN/
FRENCH VER. 105KS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.230
USB KEYBOARD KU-0355 BRAZILIAN
VER. 107KS(WITH EKEY VISTA) ROHS
KU-0355
KB.KUS03.231
USB KEYBOARD KU-0355 JPNESE
109KS(WITH EKEY VISTA) ROHS
KU-0355
KB.KUS03.232
USB KEYBOARD KU-0355 FRENCH VER.
105KEYS (WITH EKEY VISTA) ROHS
KU-0355
KB.KUS03.262
USB KEYBOARD KU-0355 SPANISH
LATIN VER. 105KS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.264
USB KEYBOARD KU-0355 US VER.
104KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.233
USB KEYBOARD KU-0355 INL US VER.
104KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.234
USB KEYBOARD KU-0355 ARABIC VER.
104KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.235
USB KEYBOARD KU-0355 GERMANY
VER. 105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.236
USB KEYBOARD KU-0355 ITALIAN VER.
105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.237
USB KEYBOARD KU-0355 FRENCH VER.
105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.238
USB KEYBOARD KU-0355 SWEDEN VER.
105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.239
USB KEYBOARD KU-0355 UK VER.
105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.240
USB KEYBOARD KU-0355 SPANISH VER.
105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.241
USB KEYBOARD KU-0355 DUTCH VER.
105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.242
Chapter 6
70
PARTNAME
71
DESCRIPTION
ACER PART NO.
USB KEYBOARD KU-0355 PORTUGESE
VER. 105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.243
USB KEYBOARD KU-0355 SWISS VER.
105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.244
USB KEYBOARD KU-0355 BELGIUM
VER. 105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.245
USB KEYBOARD KU-0355 ICELAND VER.
105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.247
USB KEYBOARD KU-0355 NORWEGIAN
VER. 105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.248
USB KEYBOARD KU-0355 HEBREW VER.
104KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.249
USB KEYBOARD KU-0355 POLISH VER.
105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.250
USB KEYBOARD KU-0355 SLOVENIAN
VER. 105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.251
USB KEYBOARD KU-0355 SLOVAKIAN
VER. 105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.252
USB KEYBOARD KU-0355 TURKEY VER.
105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.253
USB KEYBOARD KU-0355 RUSSIAMVER.
104KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.254
USB KEYBOARD KU-0355 HUNGARIA
VER. 105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.255
USB KEYBOARD KU-0355 GREEK VER.
104KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.256
USB KEYBOARD KU-0355 DENMARK
VER. 104KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.257
USB KEYBOARD KU-0355 CZECH VER.
104KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.258
USB KEYBOARD KU-0355 ITALIAN NEW
LAYOUT 105KS JPN ABS(WITH EKEY
VISTA) ROHS
KU-0355
KB.KUS03.259
USB KEYBOARD KU-0355 ROMANIAN
VER. 105KS JPN ABS(WITH EKEY VISTA)
ROHS
KU-0355
KB.KUS03.260
Chapter 6
PARTNAME
DESCRIPTION
ACER PART NO.
USB KEYBOARD KU-0355 TURKEY/
FRENCH VER. 105KS JPN ABS(WITH
EKEY VISTA) ROHS
KU-0355
KB.KUS03.261
USB KEYBOARD KU-0355
FRENCH+ARABIC 105KS (WITH EKEY
VISTA) ROHS
KU-0355
KB.KUS03.263
"USB KEYBOARD,KU-0355,US
VER.,104KS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.177
"USB KEYBOARD,KU-0355,T.CHINESE
VER.,104KS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.178
"USB KEYBOARD, KU-0355, S.CHINESE,
104KS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.179
"USB KEYBOARD,KU-0355,INL US
VER.,104KS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.180
"USB KEYBOARD,KU-0355,ARABIC
VER.,104KS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.181
"USB KEYBOARD,KU-0355,THAI
VER.,104KS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.182
"USB KEYBOARD,KU-0355,SPANISH
VER.,105KS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.183
"USB KEYBOARD,KU-0355,PORTUGESE
VER.,105KS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.184
"USB KEYBOARD,KU-0355,CANADIAN/
FRENCH VER.,105KS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.185
"USB KEYBOARD,KU-0355,BRAZILIAN
VER.,107KS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.186
"USB KEYBOARD,KU0355,JPNESE,109KS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.187
"USB KEYBOARD,KU-0355,US
VER.,104KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.188
"USB KEYBOARD,KU-0355,INL US
VER.,104KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.189
"USB KEYBOARD,KU-0355,ARABIC
VER.,104KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.190
"USB KEYBOARD,KU-0355,GERMANY
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.191
"USB KEYBOARD,KU-0355,ITALIAN
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.192
"USB KEYBOARD,KU-0355,FRENCH
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.193
"USB KEYBOARD,KU-0355,SWEDEN
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.194
Chapter 6
72
PARTNAME
73
DESCRIPTION
ACER PART NO.
"USB KEYBOARD,KU-0355,UK
VER.,104KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.195
"USB KEYBOARD,KU-0355,SPANISH
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.196
"USB KEYBOARD,KU-0355,DUTCH
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.197
"USB KEYBOARD,KU-0355,PORTUGESE
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.198
"USB KEYBOARD,KU-0355,SWISS
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.199
"USB KEYBOARD,KU-0355,BELGIUM
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.200
"USB KEYBOARD,KU-0355,HOLLAND
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.201
"USB KEYBOARD,KU-0355,ICELAND
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.202
"USB KEYBOARD,KU0355,NORWEGIAN VER.,105KS,JPN
ABS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.203
"USB KEYBOARD,KU-0355,HEBREW
VER.,104KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.204
"USB KEYBOARD,KU-0355,POLISH
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.205
"USB KEYBOARD,KU-0355,SLOVENIAN
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.206
"USB KEYBOARD,KU-0355,SLOVAKIAN
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.207
"USB KEYBOARD,KU-0355,TURKEY
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.208
"USB KEYBOARD,KU0355,RUSSIAMVER.,104KS,JPN
ABS(WITH EKEY),ROHS"
KU-0355
KB.KUS03.209
"USB KEYBOARD,KU-0355,HUNGARIA
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.210
"USB KEYBOARD,KU-0355,GREEK
VER.,104KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.211
Chapter 6
PARTNAME
DESCRIPTION
ACER PART NO.
"USB KEYBOARD,KU-0355,DENMARK
VER.,104KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.212
"USB KEYBOARD,KU-0355,CZECH
VER.,104KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.213
"USB KEYBOARD,KU-0355,ITALIAN
NEW LAYOUT,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.214
"USB KEYBOARD,KU-0355,ROMANIAN
VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.215
"USB KEYBOARD,KU-0355,TURKEY/
FRENCH VER.,105KS,JPN ABS(WITH
EKEY),ROHS"
KU-0355
KB.KUS03.216
"USB KEYBOARD, KU-0355, FRENCH
VER., 105KEYS (WITH EKEY), ROHS"
KU-0355
KB.KUS03.217
"USB KEYBOARD, KU-0355,
FRENCH+ARABIC, 105KS (WITH EKEY),
ROHS"
KU-0355
KB.KUS03.218
"WIRELESS KB, COCOON, TC VER., 104
KEYS(WITH EKEY) ROHS, WITH STK
LABE"
Y-RAJ56A
KB.CCN04.030
"WIRELESS KB, COCOON, US VER., 104
KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.029
"WIRELESS KB, COCOON, TC VER., 104
KEYS(WITH EKEY) ROHS, WITH STK
LABE"
Y-RAJ56A
KB.CCN04.030
"WIRELESS KB, COCOON, INTL US VER.,
104 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.031
"WIRELESS KB, COCOON, ARABIC VER.,
104 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.032
"WIRELESS KB, COCOON, THAI VER.,
104 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.033
"WIRELESS KB, COCOON, GERMANY
VER., 105 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.034
"WIRELESS KB, COCOON, ITALIAN VER.,
105 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.035
"WIRELESS KB, COCOON, FRENCH VER.,
105 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.036
"WIRELESS KB, COCOON, SWEDEN
VER., 105 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.037
"WIRELESS KB, COCOON, SPANISH
VER., 105 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.038
"WIRELESS KB, COCOON, UK VER., 105
KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.039
"WIRELESS KB, COCOON, SWISS VER.,
105 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.040
"WIRELESS KB, COCOON, BELGIUM
VER., 105 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.041
Chapter 6
74
PARTNAME
75
DESCRIPTION
ACER PART NO.
"WIRELESS KB, COCOON, CZECH VER.,
104 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.042
"WIRELESS KB, COCOON, RUSSIAN
VER., 104 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.043
"WIRELESS KB, COCOON, DENMARK
VER., 105 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.044
"WIRELESS KB, COCOON, DUTCH VER.,
105 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.045
"WIRELESS KB, COCOON, PORTUGESE
VER., 105 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.046
"WIRELESS KB, COCOON, SLOVAK VER.,
105 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.047
"WIRELESS KB, COCOON, ICELAND
VER., 105 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.048
"WIRELESS KB, COCOON, NORWEGIAN
VER., 105 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.049
"WIRELESS KB, COCOON, HEBREW
VER., 105 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.050
"WIRELESS KB, COCOON, POLISH VER.,
105 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.051
"WIRELESS KB, COCOON, SLOVENIAN
VER., 105 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.052
"WIRELESS KB, COCOON, TURKEY VER.,
105 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.053
"WIRELESS KB, COCOON, HUNGARIA
VER., 105 KEYS(WITH EKEY) ROHS "
Y-RAJ56A
KB.CCN04.054
"WIRELESS KB, COCOON, GREEK VER.,
104 KEYS(WITH EKEY) ROHS"
Y-RAJ56A
KB.CCN04.055
"WIRELESS KB, COCOON, CANADIAN/
FRENCH VER., 105 KEYS(WITH EKEY)
ROHS "
Y-RAJ56A
KB.CCN04.056
WIRELESS KB COCOON US VER. 104
KEYS(WITH EKEY) SILVER HEAD ROHS
Y-RAJ56A
KB.CCN04.057
WIRELESS KB COCOON US VER. 104
KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.087
WIRELESS KB COCOON TC VER. 104
KEYS(WITH EKEY VISTA) ROHS WITH
STK LABEL
Y-RAJ56A
KB.CCN04.088
WIRELESS KB COCOON INTL US VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.089
WIRELESS KB COCOON ARABIC VER.
104 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.090
WIRELESS KB COCOON THAI VER. 104
KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.091
WIRELESS KB COCOON GERMANY VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.092
WIRELESS KB COCOON ITALIAN VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.093
WIRELESS KB COCOON FRENCH VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.094
Chapter 6
PARTNAME
DESCRIPTION
ACER PART NO.
WIRELESS KB COCOON SWEDEN VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.095
WIRELESS KB COCOON SPANISH VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.096
WIRELESS KB COCOON UK VER. 105
KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.097
WIRELESS KB COCOON SWISS VER. 105
KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.098
WIRELESS KB COCOON BELGIUM VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.099
WIRELESS KB COCOON CZECH VER. 104
KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.100
WIRELESS KB COCOON RUSSIAN VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.101
WIRELESS KB COCOON DENMARK VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.102
WIRELESS KB COCOON DUTCH VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.103
WIRELESS KB COCOON PORTUGESE
VER. 105 KEYS(WITH EKEY VISTA)
ROHS
Y-RAJ56A
KB.CCN04.104
WIRELESS KB COCOON SLOVAK VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.105
WIRELESS KB COCOON ICELAND VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.106
WIRELESS KB COCOON NORWEGIAN
VER. 105 KEYS(WITH EKEY VISTA)
ROHS
Y-RAJ56A
KB.CCN04.107
WIRELESS KB COCOON HEBREW VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.108
WIRELESS KB COCOON POLISH VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.109
WIRELESS KB COCOON SLOVENIAN
VER. 105 KEYS(WITH EKEY VISTA)
ROHS
Y-RAJ56A
KB.CCN04.110
WIRELESS KB COCOON TURKEY VER.
105 KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.111
WIRELESS KB COCOON HUNGARIA
VER. 105 KEYS(WITH EKEY VISTA)
ROHS
Y-RAJ56A
KB.CCN04.112
WIRELESS KB COCOON GREEK VER. 104
KEYS(WITH EKEY VISTA) ROHS
Y-RAJ56A
KB.CCN04.113
WIRELESS KB COCOON CANADIAN/
FRENCH VER. 105 KEYS(WITH EKEY
VISTA) ROHS
Y-RAJ56A
KB.CCN04.114
"DDR2 533 256MB,
32MX64,HYS64T32000HU-3.7-B
(0.09U), ROHS"
HYS64T32000HU-3.7-B
KN.25602.033
"DDR2 533 512MB,NT512T64U88A0BY37B(PB-FREE)"
NT512T64U88A0BY-37B
KN.51203.021
MEMORY
Chapter 6
76
PARTNAME
DESCRIPTION
ACER PART NO.
"DDR2 533
1024MB,NT1GT64U8HA0BY-37B (PBFREE)"
NT1GT64U8HA0BY-37B
KN.1GB03.007
"HYNIX DDR2 533
256MB,HYMP532U64BP6-C4 (0.09UM)"
HYMP532U64BP6-C4
KN.2560G.015
"HYNIX DDR2 533
512MB,HYMP564U64BP8-C4 (0.09UM)"
HYMP564U64BP8-C4
KN.5120G.016
"USB OPTICAL MOUSE, N12ROU,
ROHS"
N12ROU
MS.N1204.001
"USB OPTICAL MOUSE, MUV ACR1, W/
STK LABEL, ROHS"
M-UV ACR1
MS.MUV01.005
"LOGITECH WIRELESS MOUSE, MRAU95, ROHS"
M-RAU95
MS.RAF01.004
POWER SUPPLY FSP ATX-250PA(1)
(NON-PFC) (250W)
ATX-250PA(1)
PY.25008.018
POWER SUPPLY FSP ATX-250PA(1PF)
(PFC) (250W)
ATX-250PA(1PF)
PY.25008.019
"M-1118B,LF"
SP.11805.003
MOUSE
POWER SUPPLY
SPEAKER
"JS 2.0 SPEAKER, USB, M-1118B, ACER
LOGO,ROHS"
77
Chapter 6