VeritonM670G/M670/
S670G/S670
Service Guide
Service guide files and updates are
available on the AIPG/CSD web; for
more information please refer to
http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on VeritonM670G/M670/
S670G/S670 service guide.
Date
Chapter
Updates
II
Copyright
Copyright © 2008 by Acer Incorporated. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or
by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed
or implied, with respect to the contents hereof and specifically disclaims any
warranties of merchantability or fitness for any particular purpose. Any Acer
Incorporated software described in this manual is sold or licensed "as is".
Should the programs prove defective following their purchase, the buyer (and
not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of
all necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium 4 and Celeron are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks
of their respective holders.
III
Conventions
The following conventions are used in this manual:
SCREEN
Denotes actual messages that appear on screen.
MESSAGES
NOTE
Gives bits and pieces of additional information
related to the current topic.
WARNING
Alerts you to any damage that might result from
doing or not doing specific actions.
CAUTION
Gives precautionary measures to avoid possible
hardware or software problems.
IMPORTANT Remind you to do specific actions relevant to the
accomplishment of procedures.
IV
Preface
Before using this information and the product it supports, please read the
following general information.
1. This Service Guide provides you with all technical information relating to
the BASIC CONFIGURATION decided for Acer's "global" product offering.
To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the
functionality of a machine (e.g. add-on card, modem, or extra memory
capability). These LOCALIZED FEATURES will NOT be covered in this
generic service guide. In such cases, please contact your regional offices or
the responsible personnel/channel to provide you with further technical
details.
2. Please note WHEN ORDERING FRU PARTS, that you should check the
most up-to-date information available on your regional web or channel. If,
for whatever reason, a part number change is made, it will not be noted in
the printed Service Guide. For ACER-AUTHORIZED SERVICE
PROVIDERS, your Acer office may have a DIFFERENT part number code
to those given in the FRU list of this printed Service Guide. You MUST use
the list provided by your regional Acer office to order FRU parts for repair
and service of customer machines.
V
Chapter 1 System Specifications 1
Features……………………………………………………………………………………………... 1
Main board Placement…………………………………………………….……..……………..6
Block Diagram…………………………………………………………..………………...………..8
VeritonM670G/M670 Front Panel………………..…….……………………….…..……....9
VeritonM670G/M670 Rear Panel…………………………………………..…….………10
VeritonS670G/S670 Front Panel………………..…………………………..…..……...11
VeritonS670G/S670Rear Panel…………………………..………..…………………12
Hardware Specifications and Configurations………………….…….……..13
Power Management Function (ACPI support function)…………………………..…...18
Chapter 2 System Utilities 19
Entering Setup…………………………………………………………………………..20
Product Information………………………………………………………..21
Standard CMOS Setup………………………….…….……………………………………22
Advanced BIOS Features………………………………………..……………………23
Advanced Chipset Setup………………………...…………………………………………..25
Integrated Peripherals…………………………...…………………………………………..26
Power Management…………………………………………………………28
PC Health Status……………………………………………………………...29
Frequency/Voltage Control……………..………………………….…….30
BIOS Security Features…………..…………………………….…….31
Load Default Settings………………………………………………..……. 32
Save & Exit Setup………………………………………………….…………33
Exit Without Saving………………………………………………….……..34
Chapter 3 Machine Disassembly and Replacement 35
General Information………………………………………………………. 36
Disassembly Procedure……………………………………………………37
VeritonM670G/M670/S670G/S670 Disassembly Procedure……………38
Chapter 4 Troubleshooting 52
Chapter 5 Jumper and Connector Information 53
Jumper Setting…………………………………………………..………………..53
Chapter 6 FRU (Field Replaceable Unit) List 59
Exploded Diagram………………………………………………………….60
Chapter 1
System Specifications
Features
Operating System
…
Microsoft Windows Vista (Home Basic, Home Premium, Business)
Processor
…
Socket Type: Intel® Socket T LGA 775 pin
…
Processor Type:
…
Intel Conroe/Kensfield/Wolfdale/Yorkfield processor FSB
1333/1066/800 MHz
Chipset
…
Intel Q45+ ICH10DO
PCB
…
Form Factor: Micro ATX
…
Dimension/Layer: 244mm x244mm
Memory
…
512MB / 1GB / 2GB DDR3 /1066/800 Un-buffered Non-ECC DIMM
support
…
Support single channel 64 bit mode with maximum memory size up to 8GB
…
Support un-buffered DIMM (Intel Q35/Q33)
…
DIMM Slot: 4
…
Memory Max: 512MB to 8GB DDR2 memory technologies
PCI
…
PCI Express Slot Type: x16
…
…
PCI Express Slot Type: x1
…
…
PCI Express x16 Slot Quantity: 1
PCI Express x1 Slot Quantity: 1
PCI Slot Type: PCI 2.3 5V slots
1
…
PCI Slot Quantity: 2
FDD
…
Slot Quantity: 1
…
Design Criteria:
…
Should support 1.44MB/3 mode 3.5” Devices
SATA
…
Slot Type: SATA slot
…
Slot Quantity: 6
…
Storage Type support:
…
HDD/CD-ROM/CD-RW/DVD-ROM/DVD-RW/DVD+RW/DVD
Dual/DVD SuperMulti Plus/
Audio
…
Audio Type: HD audio codec
…
Audio Channel: 7.1 channel
…
Audio Controller /Codec: ALC888S HD codec 7.1
…
Connectors support:
…
Rear 6 jack follow HD audio definition, example as below
…
Audio jacks color coding: should meet Microsoft Windows Logo Program
Device Requirements: Audio-0002
…
1 S/PDIF-out header (1*4)
…
1 AUX-In header (1*4)
…
1 front panel audio header (2*5)
…
Add HD de-pop CKT (the attachment is the reference, please propose
your solution)
…
S/N ratio: 90 dB at rear output jack
LAN
…
MAC Controller: ICH10DO
2
…
10M/100M/1000M LAN
…
PHY: Intel Boazman 82567LM PCI-E Giga LAN
USB
…
Controller Type: Intel ICH10DO
…
Ports Quantity: 12
…
…
6 back panel ports
…
On-board: 3 2*5 headers
…
4 ports for front daughter board
…
2 ports reserved
…
Connector Pin: standard Intel FPIO pin definition
Data transfer rate support:
…
USB 2.0/1.1
BIOS
…
BIOS Type: Phoenix Award or AMI Kernel with Acer skin
…
Size: 32Mb
…
Note:
…
Boot ROM should be included (PXE function should be built in with
default and RPL function is optional by service BIOS)
…
BIOS shall auto detect FDD to avoid checksum error when boot
I/O Connector
…
Controller: Super I/O ITE 8720 (F stepping or after; must full support Intel
platform)
Rear I/O Connector
…
1 PS/2 Keyboard port,
…
1 PS/2 Mouse port
…
1 serial port
…
1 D-Sub VGA port
3
…
1 DVI-D VGA port
…
1 RJ45 LAN port
…
6 USB ports
…
7.1 channel phone jack (6 audio jacks)
On-board connectors
…
1 LGA 775 CPU socket
…
4 DDR3 memory sockets
…
1 PCI Express x16 slot
…
1 PCI Express x 1 slot
…
2 PCI slot
…
1 FDD slot
…
6 SATAII connectors
…
3 2*5 pin Intel FPIO specification USB pin connectors (follow Intel FPIO
standard Specification)
…
1 2*5 pin Intel FPIO spec. Microphone In/ Headphone Out pin connectors
…
1 serial port 2*5 pin connector (2nd serial port)
…
1 2*4 pin internal speaker header
…
1 4 pin CPU Fan connector
…
1 3 pin System FAN connector with linear circuit
…
1 2pin Intrusion Alarm connector
…
1 24pin + 4pin ATX interface PS3/PS2 SPS connector
…
1 2*7 pin front panel IO header
…
1 Jumper for clear CMOS
…
1 on board buzzer
…
1 2pin OBR header
…
2 reserved 2pin GPIO connector
…
Color management for on board connecter (pls refer to Acer spec)
4
…
1 x LTP 2*13pin header
…
1 2x5pin Front Audio header
…
1 3pin ME enable/disable connector (with 1 jumper)
Power Supply
…
…
Power Supply Mounting Features
…
Chassis accepts ATX-style power supply
…
Chasses accepts PS2, PS3 style power supply
…
Features for internal mounting tab
…
Location of 4 external mounting holes
Power Supply Electrical Design Feature
…
300W/250W in stable mode (Acer Assign System Power Unit)
…
Design for Intel Broadwater/ICH8 series chipset compatible system
…
Voltage design should be covered +5V, +3.3V, +12V, +5VSB, -12V
(attention to 12V output capability)
…
Demand for both PFC/Non-PFC solutions (two different quotations are
needed)
…
Minimum 2 Serial ATA power connector solution should be included (by
default)
…
Minimum 3 big 4-pin power connector included
…
Minimum 1 small 4-pin power connector included
…
PFC version will not provide switch selector for 115/230V AC input but it
should be universal for Europe and China
…
Non-PFC version should provide switch selector for 115/230V AC input
and universal for worldwide
…
PS2 style
5
Main board Placement
6
7
Block Diagram
8
VeritonM670G/ M670 Front Panel
Label
Description
1
USB ports
2
ACER Logo
3
FDD cover
4
LEDs
5
MIC connector
6
Audio connector
7
Optical drive
8
Card reader
9
Power Button
9
VeritonM670G/ M670 Rear Panel
Label
Description
Label
Description
1
Power card socket
8
Printer connector
2
Voltage selector switch
9
PS/2 mouse connector
3
PS/2 keyboard connector
10
Monitor connector
4
DVI port
11
LAN connector
5
USB 2.0 ports
12
Lock Handle
6
Audio connector
7
Fan aperture
10
VeritonS670G/S670 Front Panel
Label
Description
1
Power Button
2
Optical drive
3
FDD cover
4
ACER Logo
5
Audio connector
6
USB ports
7
Card reader
11
VeritonS670G/S670 Rear Panel
Label
Description
Label
Description
1
Power card socket
6
Audio connector
2
PS/2 keyboard connector
7
Com connector
3
PS/2 mouse connector
8
Monitor connector
4
DVI port
9
LAN connector
5
USB 2.0 ports
10
12
Hardware Specifications and Configurations
Processor
Item
Specification
Type
Processor Type: Intel Conroe /Kensfield /Wolfdale
/Yorkfield processor FSB 1333/1066/800 MHz CPUs
Socket
LGA 775 pin
FSB
800/1066/1333 MHz CPUs
Minimum operating speed
0 MHz (If Stop CPU Clock in Sleep State in BIOS
Setup is set to Enabled.)
BIOS
Item
Specification
BIOS code programmer
Phoenix Award or AMI Kernel with Acer skin
BIOS version
V6.0
BIOS ROM type
SPI Flash
BIOS ROM size
32Mb
Support protocol
SMBIOS (DMI) 2.4/DMI 2.0 (log file)
Device Boot Support
-
Support to LS-120 drive
YES
Support to BIOS boot block
feature
YES
1st priority: SATA HDD
2nd priority: CD-ROM
3rd priority: FDD
4th priority: LAN
5th priority: USB device
BIOS Hotkey List
Hotkey
Del
Function
Enter BIOS Setup Utility
Description
Press while the system is booting to enter
BIOS Setup Utility.
13
Main Board Major Chips
Item
Specification
North Bridge
South Bridge
Intel Q35 and Q33
Intel ICH9DO/ICH9
APG controller
Intel Q45
Super I/O controller
ITE 8718
Audio controller
HD audio codec ALC888S HD codec 7.1 (co-lay with LC888)
LAN controller
Intel Boazman 82567LM PCI-E Giga LAN
HDD controller
Intel ICH10DO
Keyboard controller
Super I/O ITE 8720
Memory Combinations
Slot
Memory
Total Memory
Slot 1
512MB, 1GB, 2GB
512MB~2GB
Slot 2
512MB, 1GB, 2GB
512MB~2GB
Maximum System Memory Supported
512MB~8GB
System Memory
Item
Specification
Memory slot number
4 slot
Support Memory size per socket
512MB/1GB/2GB
Support memory type
DDR3
Support memory interface
DDR3 800/1066MHz
Support memory voltage
1.8V
Support memory module package
240-pin DDR3
Support to parity check feature
Yes
Support to error correction code (ECC) feature
No
Memory module combinations
You can install memory modules in
any combination as long as they
match the above specifications.
14
Audio Interface
Item
Specification
Audio controller
Intel ICH9DO/ICH9
Audio controller type
ALC888S
Audio channel
codec 7.1
Audio function control
Enable/disable by BIOS Setup
Mono or stereo
Stereo
Compatibility
Sound Blaster Pro/16 compatible Mixed
digital and analog high performance
chip Enhanced stereo full duplex
operation High performance audio
accelerator and AC’97 support Full
native DOS games compatibility Virtual
FM enhances audio experience through
real-time FM-to-Wavetable
conversionMPU-401 (UART mode)
interface for Wavetable synthesizers and
MIDI devices Integrated dual game port
Meets AC’97and WHQL specifications
Music synthesizer
Yes, internal FM synthesizer
Sampling rate
48 KHz (max.)
MPU-401 UART support
Yes
Microphone jack
Supported
Headphone jack
Supported
SATA Interface
Item
Specification
SATA controller
Intel ICH10DO
SATA controller resident bus
PCI bus
Number of SATA channel
SATA X 6
Support bootable CD-ROM
YES
15
Floppy disk drive Interface
Item
Floppy disk drive controller
Specification
Super I/O ITE 8720
Floppy disk drive controller resident bus ISA bus
Support FDD format
360KB, 720KB, 1.2MB, 1.44MB, 2.88MB
USB Port
Item
Specification
Universal HCI
USB 2.0/1.1
USB Class
Support legacy keyboard for legacy mode
USB Connectors Quantity
4 ports for front daughter board
4 ports for rear I/O
2 ports for internal card reader.
Environmental Requirements
Item
Specification
Temperature
Operating
+5°C ~ +35°C
Non-operating
-20 ~ +60°C (Storage package)
Humidity
Operating
15% to 80% RH
Non-operating
10% to 90% RH
Vibration
Operating
(unpacked)
5 ~ 500 Hz: 2.20g RMS random, 10 minutes per axis in all 3 axes
5 ~500 Hz: 1.09g RMS random, 1 hour per axis in all 3 axes
16
Power Management
Devices
S1
S3
S4
S5
Power Button
V
V
V
V
USB Keyboard/Mouse
V
V
N/A
N/A
PME
Disabled
Disabled
Disabled
Disabled
RCT
Disabled
Disabled
Disabled
Disabled
WOR
Disabled
Disabled
Disabled
Disabled
…
…
Devices wake up from S3 should be less than
Devices wake up from S5 should be less than 10 seconds
17
18
Chapter 2
System Utilities
The manufacturer or the dealer already configures most systems. There
is no need to run Setup when starting the computer unless you get a Run
Setup message.
The Setup program loads configuration values into the battery-backed nonvolatile
memory called CMOS RAM.
This memory area is not part of the system RAM.
NOTE: If you repeatedly receive Run Setup messages, the battery may be bad/flat.
In this case, the system cannot retain configuration values in CMOS.
Before you run Setup, make sure that you have saved all open files. The system
reboots immediately after you exit Setup.
19
Entering Setup
Power on the computer and the system will start POST (Power On Self Test)
process. When the message of “Press DEL to enter SETUP” appears on the screen, press
the key of [Delete] to enter the setup menu.
NOTE: If the message disappears before you respond and you still wish to enter
Setup, restart the system by turning it OFF and On. You may also restart
the system by simultaneously pressing [Ctrl+ Alt+ Delete].
The Setup Utility main menu then appears:
20
The items in the main menu are explained below:
Parameter
Description
Production Information
This page shows the relevant information of the main
board
Standard CMOS Features
This setup page includes all the items in standard
compatible BIOS
Advance BIOS Features
This setup page includes all the items of Award special
enhanced features
Advance Chipset Features
This setup page includes all advanced chipset features
Integrated Peripherals
This setup page includes all onboard peripherals
Power Management Setup
This setup page includes all the items of Green function
features
PC Health Status
This setup page is the System auto detect Temperature,
voltage, and fan speed
Frequency/Voltage Control
This setup page is the System Frequency/Voltage setup
BIOS Security Features
Change, set or disable password. It allows you to limit
access to the System
Load Optimized Defaults
Load Optimized Settings Default Settings indicates the
value of the system parameters which the system would
be in best performance configuration
Save & Exit Setup
Save CMOS value settings to CMOS and exit setup
Exit Without Saving
Abandon all CMOS value changes and exit setup
21
Product Information
The screen below appears if you select Product Information from the main menu:
The Product Information menu contains general data about the system, such as the
product name, serial number, BIOS version, etc. This information is necessary for
troubleshooting (maybe required when asking for technical support).
The following table describes the parameters found in this menu:
Parameter
Description
Processor Type
This item lists the product processor model
Processor Speed
This item lists the processor frequency for the system
System Memory
Total memory size for the system
Product Name
This item lists the product name
Product Name
This item lists the system BIOS version
System Serial Number
This item lists the system serial number
System BIOS Version
This item lists the system BIOS version
BIOS Release Date
This item lists the BIOS release date
22
Standard CMOS Setup
Select standard CMOS features from the main menu to configure some basic
parameters in your system the following screen shows the standard CMOS features
menu:
The following table describes the parameters found in this menu.
Parameter
Description
Options
System Date
To set the date following
Week: From [Sun.] to [Sat.]. determined
the
by BIOS and is display only
weekday-month-date-year Day: from [1] to [31] (or the maximum
format
allowed in the month.
Year: from 1999 to 2099
System Time
To set the time following
the hour-minute-second
format
The items format is [hour]
[minute][second]. The time is calculated
base on the 24-hour timer clock.
Halt On
This item enables use to
select the situation if the
BIOS stops the POST
process and the
notification
All Errors
No Errors
All, But Keyboard
All, But Diskette
All, But Disk/Key
23
Advanced Setup
The following screen shows the Advanced Setup:
The following table describes the parameters found in this menu.
Parameter
Description
Options
Quick Boot
Allows BIOS to skip certain tests while
[Enabled],
booting. This will decrease the time needed to [Disabled]
boot the system
1 st Boot Device
The item allows you to see the sequence of
boot device where BIOS attempts to load the
disk operation system.
2 nd Boot Device
3 rd Boot Device
Hard Disk Drives
CD/DVD Drives
Specifies the boot device. Priority sequence
from available Hard Drives
Boot up Num-Lock On
Select Power-on state for Numlock
On,Off
Boot Sector Virus
Protection
This feature allows you to enable the VIRUS
warning function for Hard Disk boot sector
protection. If this function is enabled and
there is someone attempt to write data to this
area, BIOS will show a warning message on
screen and the alarm will beep.
[Enabled],
[Disabled]
USB Beep Message
Enables the beep during USB device
enumeration
[Enabled],
[Disabled]
24
Advanced Chipset Setup
The following table describes the parameters found in this menu.
Parameter
Description
Options
Intel EIST
For Intel platform
Disabled/Enabled
Intel XD Bit
For Intel platform
Disabled/Enabled
Intel VT-b
For Intel platform
Disabled/Enabled
Intel TXT
For Intel platform
Disabled/Enabled
Intel AMT
For Intel platform
Disabled/Enabled
ASF
For Veriton series with vPro or DASH solution
Disabled/Enabled
Memory Hole
Remapping
You can reserve this area of system memory
for ISA adapter ROM. When this area is
reserved, it cannot be cached. The user
information of peripherals that need to use
this area of system memory usually discuss
their memory requirements.
Disabled/Enabled
Primary Video
Priority for Auto : PCIE -> Onboard -> PCI
Auto/PCIE/Onbo
ard/PCI
25
Integrated Peripherals
26
The following table describes the parameters found in this menu.
Parameter
Description
Options
Onboard SATA Mode
This item is only available when
onboard SATA controller is enabled
Native
IDE/RAID/AHCI
Onboard USB Controller
Always enabled USB keyboard
during POST no matter what option
is set
Disabled/Enabled
Legacy USB Support
This item is only available when on
board USB controller is enabled
Disabled/Enabled
Onboard Audio Controller
Always enabled Audio POST no
matter what option is set
Disabled/Enabled
Onboard LAN Controller
Always enabled Audio POST no
matter what option is set
Disabled/Enabled
Onboard LAN Option ROM
This item is only available when
onboard LAN controller is enabled
Disabled/Enabled
Onboard Floppy Controller
Always enabled FloppyOST no
matter what option is set
Disabled/Enabled
Serial Port1 Address
Allows BIOS to select serial port1
base addresses
Disabled /
3F8/IRQ4 /
2F8/IRQ3 /
3E8/IRQ4 /
2E8/IRQ3
Serial Port2 Address
Allows BIOS to select serial port1
base addresses
Disabled /
3F8/IRQ4 /
2F8/IRQ3 /
3E8/IRQ4 /
2E8/IRQ3
Serial Port2 Mode
Allows BIOS to select serial port1
base Mode
Normal/IrDA/ASK
IR
Parallel Port Address
Allows BIOS to select parallel port
base addresses
Parallel Port
Address
Parallel Port Mode
Allows BIOS to select parallel port
base Mode
Normal//EPP/ECP
/EPP+ECP
Parallel Port IRQ
Allows BIOS to select parallel port
base IRQ
27
Power Management
The Power Management menu lets you configure your system to most effectively save
energy while operating in a manner consistent with your own style of computer use. The
following screen shows the Power Management parameters and their default settings:
The following table describes the parameters found in this menu.
Parameter
ACPI Aware O/S
ACPI Suspend Mode
Description
Control wake up event for
S1/S3/S4/S5
Options
No/Yes
S1(POS)/S3 (STR)
Power On by RTC Alarm
Disabled/Enabled
Power On by PCIE Devices
Disabled/Enabled
Power On by PCI Devices
Disabled/Enabled
Power On by Modem Ring
Disabled/Enabled
Wake Up by PS/2 KB/Mouse
Wake Up by USB KB//Mouse
Control wake up event for
S1/S3
Disabled/Enabled
Disabled/Enabled
28
PC Health Status
The following table describes the parameters found in this menu:
Parameter
Description
CPU/System Temperature
Detect CPU Temperature
automatically
CPU/SYSTEM FAN Speed (RPM)
Detect CPU/SYSTEM Fan Speed
Status automatically
CPU Smart FAN Control
The item displays the system Smart
Fan Function status. It is always
enabled by system.
Options
29
Frequency/Voltage Control
The following table describes the parameters found in this menu:
Parameter
Description
Options
Auto Detect DIMM/PCI Clk
Always auto detect DIMM/PCI
Clk
Disabled/Enabled
Spread Spectrum
Always auto detect Spread
Spectrum
Disabled/Enabled
30
BIOS Security Features
The following table describes the parameters found in this menu:
Parameter
Description
Options
Change Supervisor
Password
This item is only available when
supervisor password is installed, If clear
supervisor password, user password
should also be cleared. All setup items
will be view-only except user password
item when login with user password
Press Enter
TCG/TPM SUPPORT
This item is only available when TPM
controller/module is installed
No/Yes
Execute TPM Command
This item is only available when TPM
controller/module is installed and
TCG/TPM support is yes
Don't
Change/Disab
led/Enabled
Removable Device Boot
Control system booting from floppy, USB
handy drive, or memory card
Disabled/Ena
bled
Chassis Opened Warning
For Veriton series electron lock,
Disabled/Ena
bled/Clear
31
Load Default Settings
This option opens a dialog box that lets you install defaults for all appropriate items
in the Setup Utility.
The following table describes the parameters found in this menu:
Parameter
Description
Load Default
Settings
Select the field loads the factory defaults for BIOS and
Chipset Features, which the system automatically
detects. This option opens a dialog box that lets you
install optimized defaults for all appropriate items in
the Setup Utility.
Options
32
Save & Exit Setup
Highlight this item and press <Enter> to save the changes that you have made in the
Setup Utility and exit the Setup Utility.
The following table describes the parameters found in this menu:
Parameter
Description
Options
Save & Exit Setup Press <Enter> to save the changes that have made
in the Setup Utility and exit the Setup Utility.
Press<Y> to save and Exit or <N> to return to the
main menu.
33
Exit Without Saving
Highlight this item and press <Enter> to discard any changes that you have made in
the Setup Utility and exit the Setup Utility.
Parameter
Description
Exit Without Saving
Press<Enter> to discard any changes and
exit the Setup Utility
Options
34
Chapter 3
Machine Disassembly and Replacement
To disassemble the computer, you need the following tools:
Wrist grounding strap and conductive mat for preventing electrostatic
discharge.
Wire cutter.
Phillips screwdriver (may require different size).
NOTE: The screws for the different components vary in size. During the disassembly
process, group the screws with the corresponding components to avoid
mismatches when putting back the components.
35
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the
following:
1. Turn off the power to the system and all peripherals.
2. 2.Unplug the AC adapter and all power and signal cables from the system
36
Disassembly Procedure
This section tells you how to disassemble the system when you need to perform
system service. Please also refer to the disassembly video, if available.
CAUTION: Before you proceed, make sure you have turned off the system and all
peripherals connected to it.
37
VeritonM670G/M670/S670G/S670 Standard Disassembly
Process
Bezel
Process:
1.
According to the requirement, paste ATI, OS, CPU, HDMI and marketing label by SKU.
VeritonM670G/M670
VeritonS670G/S670
38
Remove side cover
Process:
1. Put the Computer on the worktable lightly.
2. Release left side cover with 2 screws then remove left side cover.
Screw location
Push the side cover lightly
Screw location
Remove CPU fan pipe
Process:
1.
Release the CPU fan pipe.
39
Remove Cards
Process:
1. Release the slot cover tooless
2. Remove VGA 、TV、Modem Card,the following list is for your reference about the mutual
location relation (Optional by SKU).
Modem card
TV card
VGA card
Notice:
I.
Remove card, don’t touch any electric parts on PCB.
VGA card
TV card
Modem card
slot cover
40
Remove HDD Data Cables
Process:
1. Remove master HDD data cable from M/B SATA1/SATA3.
2. Remove slave ODD data cable from M/B SATA2.
SATA4
SATA3
SATA2
SATA1
Remove slave HDD cable
Remove master HDD cable
41
Remove ODD DATA cable
Process:
1.
Remove master ODD data/power cable from Master ODD.
Remove master ODD
Power Cable
Remove master
ODD Data Cable
Remove HDD power cable
Process:
1.
Remove master HDD data cable from master HDD.
2. Remove slave HDD data cable from slave HDD
Remove slave HDD
Remove master HDD
42
Remove Cables
Process:
1.
2.
3.
4.
5.
Remove front panel light cable from“PANEL1" slot of M/B.
Remove USB1 cable from M/B"F_ USB3”。
Remove USB2 cable from M/B”F_ USB4”。
Remove Card reader cable from M/B"USB2”.
Remove audio cable from the “AUDIO" port on M/B.
Notice:
I.
Recovery switch cable is next to FDD port, and the black cable face to the top of
Chassis.
II.
Intrusion switches cable face to front bezel of chassis.
Remove HDD
Process:
1. Remove Master HDD from the first HDD location.
2. Remove Slave HDD from the second HDD location. (Optional by SKU)
43
Slave HDD
Master HDD
Remove card reader
Process:
1.
Remove card reader from chassis.
44
Remove FDD Cable
Process:
1.
Remove FDD digital cable just as pictures (Optional by SKU).
2. Plug 4 pins power cord from FDD slot.
Remove from FDD
Remove from M/B
“FDD1” slot
3. Remove front bezel light cable from PATA power cable
Remove Front bezel light cable
45
Remove ODD
Process:
1. Push the lock handle release ODD.
2. Remove Master ODD from the location.
3. Remove slave ODD from the location. (Optional by SKU)
Master ODD location
Slave ODD location
46
Remove Cables
Process:
1. Remove M/B power cable from M/B “ATX1”.
2. Remove 12 V power cable from M/B” JPW1”
3. Remove System Fan cable from M/B”SYS-F2”.
MB power cable
47
Remove System FAN
Process:
1.
Release four screws according to the following picture.
2. Remove Sys FAN (Optional by SKU)
Release four screws.
4
1
2
3
The direction of System FAN
48
Remove mother board
Process:
1. Release 8 pcs screws form the corresponding hole.
2. Release screws according to the following picture in turn.
3. Remove the Mother board from chassis.
49
Remove CPU cooler
Process:
1. Remove cooler power cable from M/B “CPU-F2”.
2. Release screw 1 first, then fixes screw 2, screw 3 & screw 4 (As Picture).
3. Remove Cooler from the Retention module.
Remove memory
Process:
1. Remove the first Memory from DIMM.
2. Remove the second Memory from DIMM2 (Optional by SKU).
50
Remove CPU
Process:
1. Remove CPU according following the pictures.
Lock the
Handle
Remove I/O shielding
Process:
1. Remove I/O Shielding.
51
Chapter 4
Troubleshooting
Please refer to generic troubleshooting guide for troubleshooting information relating to
following topics:
…
Power-On Self-Test (POST)
…
POST Check Points
…
POST Error Messages List
…
Error Symptoms List
52
Chapter 5
53
54
ATX_POWER: ATX 24-pin Power Connector
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Signal Name
+3.3
+3.3
COM
+5V
COM
+5V
COM
PWR OK
5VSB
+12V
+12V
+3.3V
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Signal Name
+3.3V
-12V
COM
PS_ON
COM
COM
COM
-5V
+5V
+5V
+5V
COM
55
56
57
58
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations
of Veriton M670G/M670/S670G/S670. Refer to this chapter whenever ordering
for parts to repair or for RMA (Return Merchandise Authorization).
NOTE: Please note WHEN ORDERING FRU PARTS, that you should check the most
up-to-date information available on your regional web or channel. For whatever
reasons a part number change is made, it will not be noted in the printed Service
Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may
have a DIFFERENT part number code to those given in the FRU list of this printed
Service Guide. You MUST use the local FRU list provided by your regional Acer
office to order FRU parts for repair and service of customer machines.
59
Exploded Diagram
NO
DESCRIPTION
NO
DESCRIPTION
1
CHASSIS
18
MOTHERBOARD
2
LINE-CLIP
19
PCI-BRACKET
3
USB-SHIELD NUT 6-32#
20
FAN
4
USB-SHIELDING
21
POWER SUPPLY
5
USB PCB MODULE
22
USB-TOP
6
SIDE FOOT RUBBER
23
LOGO-SUPPORT
7
RIGHT SIDE PLATE
24
MAIN-BEZEL
8
LED/SWITCH HDLDER
25
LEFT-WIRE-NETTING
9
CD-ROM
26
ODD-COVER
10
CARDREADER DEVICE
27
FDD-COVER
11
OBR HOLDER
28
HDD-LENS
12
PLASTIC FOOT
29
FRONT-LENS-STRIP
13
CD-ROM LOCK SLIDE
30
POWER-LENS
14
FDD-LOCK-SLIDE
31
POWER-BOTTON
15
SMALL LINE CLIP
32
FRONT-STRIP-MODULE
16
HDD MOVDLE
33
SWITCH-HOLDER
17
LEFT SIDE PLATE
34
RIGHT-WIRE-NETTING
60
NO
1
2
3
4
5
6
7
DESCRIPTION
POWER SUPPLY
ACER_16L_BASE
HDD-MOUDLE
HDD-CAGE
USB-MOUDLE
LENS-HOLDER
MAIN-BEZEL
NO
12
13
14
15
16
17
18
DESCRIPTION
HOLDER-SWITCH
ODD-CAGE
ACER_16L_CHASSIS
70X70X15FAN
ACER-16L-ODD-SUPPORT-BKT
ACER-16L-SUPPORT
ACER_16L_CHASSIS_SUPPORT
8
FRONT-STRIP
19
ACER_16L_TOP_DUCK
9
FDD-COVER
20
ACER_16L_FAN_DUCK
10
ODD-COVER
21
ACER_16L_REAR_CHASSIS
11
UPGBEZEL
22
61