ALFA 40-MS User's Manual
Add to my manuals17 Pages
Alfa 40-MS is a twin-tub washing machine with a variety of features to make laundry day easier. It has two separate tubs, one for washing and one for spinning, which allows you to wash and dry your clothes in one continuous cycle. The Alfa 40-MS also features a built-in water-filling entrance, a wash selector, and a spin timer, so you can customize your wash cycle to suit your needs. Additionally, the machine has a lint filter to catch lint and debris, and a drain hose to easily drain away wastewater.
advertisement
ALFA
Twin-tub Washing Machine
User's manual
Model: 40-MS
Please read this manual carefully before using.
Retain it for future reference.
Contents
Names of the parts
Safety precautions
Installation and adjustment
Preparation before washing
The musts in washing
Usage of the detergent
Washing sequence
Disposal after washing
Trouble-Shooting *Answer to question
Packing list *Specification
Names of the parts
Spin timer
Wash selector
Wash timer
Water-filling entrance
Control panel
Overflow filter
Lint filter(Installed by user)
Valve cover
Pulsator
Wash tub
Wash tub cover
Base frame
Outer cover of the spin tub
Inner cover of the spin tub
Spin tub frame
Spin tub
Cabinet
Meaning and description of the symbols
Warning sign
Forbidding sign
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict conformity to the contents, otherwise it may
cause damage of the machine or injure the personal safety of the user.
Contents marked with that symbol are actions
forbidden to perform. Performing of those actions may result in damage of the machine or injure the personal safety of the user.
Please check if the power receptacle has good earthing condition before using to guarantee your safety.
1
Safety precautions
Please insert the power cord into special receptacle with rated voltage.Be sure to use single-phase
three pins receptacle.The earthing
terminal of the receptacle must be
earthed reliably.If possible,please adopt electric leakage protector.
When the machine is normally using, please put the power plug at the location easily to be inserted and extracted by hand. Be sure to pull the plug off when there's power failure, or the machine is being moved, cleaned or when it is idle.
If the power cord is bad, to avoid risk it is required to replace it by the technicians of our special shop or the after-sale service department.
Keep the pin of the power plug clean.
Do not put the machine at damp place like the bathroom . Never wash it with water. Do not place wet laundries on the control panel.
Do not use water hotter than 50 C .
In case the washing machine is installed on ground with carpet , do not block the ventilation hole with carpet.
Ventilation hole at the bottom of the washing machine
Do not wash water-proof laundries like the raincoat, bike covers etc. to avoid abnormal vibrations in spinning.
2
Do not let the machine share one receptacle with other electric appliances. If the power plug is damaged, or the plugging into the receptacle is loose, do not use the plug any more.
Safety precautions
Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children.
Do not decompose, repair or alter the machine by yourself.
Do not put any hot or heavy items
( such as the kettle with hot water ) on the washing machine.
Do not wash laundries with volatile materials (such as thinner, petrol etc.).
Petrol
Thinner
Handicapped or children without care shall not use the machine.
Keep the machine away from direct sunlight and heat source like the
heater.
To protect your laundries and washing machine, please take out all of the coins, buttons, sand, hairpin and other foreign materials before washing.
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing
powder.
3
4
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating
the machine.
Install the lint filter
After opening the package,please take out the lint filter from the document bag,install it to the overflow filter of the wash tub.See to the figure.
Overflow filter
Lint filter
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than 1.2m ,
or the drainage will not be smooth enough and cause
incomplete drainage.
<1.2m
2.Do not step on or press the drain hose.
How to change the direction of the drain hoses
Figure 1 indicates the ex factory installation position of the drain hose.
Soft item
Extend the drain hose from the side of spin tub
Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. Take off the drain hose from the cabinet.
Take the hose out of the fixing groove.
(See to Figure 2).
Embed the drain hose into the groove along the side of the spin tub in the order of (1)~(3), heading
for the side of the spin tub. (See to Figure 3).
Soft item
Back
Front
Figure 1
Figure 2
Embed the drain hose into the groove with hands. Take care not to damage the drain hose in fastening the fixing clamp.
Extend the drain hose from the rear side
Extend to the spin tub side
Take out the drain hose from the fixing groove.
Extend it from the rear side as per the direction
of the arrow. (When the drainhose is extended
from the rear side, it can be hung on the point for drain hose at the two sides of the cabinet.)
(See to Figure 4).
Embed into the groove in turn
Figure 3
Figure 4
Install the water inlet hose; Select the water level
Water inlet hose
Insert the water inlet hose into the water-filling entrance on the control panel.
Water inlet
Select water level according to the quantity of the laundries.
Set the water level adjusting lever
to needed line.
Water level indicator
Maximum Max
Medium
Minimum
Med
Min
5
Preparation before washing
Preparation before washing
1.Connect the water inlet hose.
2.Confirm that the washing machine is earthed
reliably . Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.
Put the drain hose up to suitable position.
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
Pay attention to followings before washing the laundries
Check if the laundries has special requirement on washing
Clear the pocket. Take out the coins, sand, hairpins etc.
Tie the long strips; fasten the buttons; close zippers.
The quantity of the laundries shall not be too large. Stretch and loosen the laundries before putting them in the tub.
When the pulsator is running , the buttons of the laundries may cause noise. For the sake of discretion, please put the laundries with buttons into other laundries.
6 a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
d. For those laundries with heavy soil, please first remove the dirt like
mud or dust. For the parts with heavy soil, please apply detergent on
them in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn
it over before putting in.
f. Do not put those laundries polluted by chemicals into the washing
machine directly.
The musts in washing
The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can
be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity.
The thickness ,size , type of the cloth will influence the actual washing capacity. It is suitable to put in reasonable amount of laundries and the laundries can be turned round in washing for one time washing.
Do not select " Maximum " water level for
laundries less than 2.4kg, so as to avoid splashing of water.
It is suggested not to use high sudsing detergent.
Usage of the detergent
How to use the whitener How to use the washing powder
Fill water to decided level. Dilute
the whitener with container.
Pour it slowly into the washing tub.
Avoid using whitener on laundries with color or pattern as they
are prone to lose color.
The whitener shall not touch the laundries directly.
Refer to the user's manual for the usage and quantity of the whitener.
For powder whitener, please dissolve it before using.
Direct dissolved in the machine:
1.Fill small quantity of water.
2.Add the powder . Run for 30
seconds to dissolve it completely.
3.Put it in the laundries. Select suitable
water level.
The instant dissolving of the washing
powder:
1.Prepare warm water of 30 C and a
container.
2.Add the powder while stirring to fully
dissolve it.
The powder is more prone to pollute the laundries than the detergent. Therefore please use it with proper quantity.
Dosage of different washing powder is different. Please refer to the instruction of the washing powder for the detail dosage.
7
8
Washing sequence
Water inlet
Wash timer
(To set to below 2 minute, first set to 5 minute then turn it back. it can increase the service life of the timer).
OFF
Wash selector
(standard current,
soft current)
STANDARD
SOFT
DRAIN
WASH SELECTOR
WASH TIMER
Spin timer
(to set to below 1 minute,
first set to 2 minute then
turn it back. it can increase
the service life of the timer).
OFF
SPIN TIMER
Wash
1. Fill the water and add the dissolved washing
powder to make the water level reach the preset
position. (Figure 1)
Run washing program for some time to stir and
dissolve the powder completely.
STANDARD
SOFT
2.Put in the laundries. If the water quantity is
insufficient, please add water.
3.Select the current.
Select the strength of the current according to
the laundries. (Figure 2)
4.Select the washing time
Select the washing time according to the
laundries. (Figure 3)
5.After washing, set the "WASH SELECTOR"
at "DRAIN". (Figure 4).
WASH SELECTOR
OFF
WASH TIMER
STANDARD
SOFT
Figure 1
DRAIN
Figure 2
Figure 3
DRAIN
Figure 4
WASH SELECTOR
Spinning
1.
Put the laundries into the spin tub evenly and smoothly.
2.
Spin
(1) Put the gland in properly.
Please put in the gland properly even if the laundries quantity is small.
Push Gland
Push
Proper The laundries are slanting
Proper No gland
(2) Close the inner and outer cover of the spin tub.
Outer cover of
The spin tub
Inner cover of
The spin tub
(3). Spin
Select suitable spin time according to the laundries, and do spinning.
During spinning, if there's abnormal sound, it is generally owing to
slanting placement of the laundries. Please stop the machine
and re-order the laundries.
In spinning, it will pause the work if you open the outer cover of the spin
tub. Close it to resume the spinning.
To do spinning and drainin together, please first do spinning for around 1 minute, then
do draining . Otherwise the spinning will stop
owing to too much water stored in the spin
tub.
9
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine.
Please first pull off the power plug from the receptacle before cleaning.
Cleaning the lint filter
The lint filter must be used during washing.
It must be cleaned in time after each using.
1. Take off the lint filter
Put hand at the indicated position.
Push down to take it off. ( See to
Figure 1)
2. Clean the lint
Put it in water and clean while it is
still wet.(See to Figure 2)
Figure 1
3. Install the lint filter
After cleaning, insert the bottom
of the lint filter ( marked with
"down side") into the overflow filter ,
then push the upper part of the
Figure 2
filter in ( marked with " up side ").
(See to Figure 3)
10
Cleaning the overflow filter
Too much lint on the overflow filter will influence the normal usage of the machine. Please clean it every two months.
1 Take off the overflow filter.
Elastic fixing claw
As indicated in the figure, nip the elastic fixing
claw and pull it to the direction of the arrow to
take it off.
Figure 3
Cleaning the overflow filter
2. Cleaning the overflow filter
Clean the lint around the filter
and flush with tap water.
3. Install the overflow filter.
(1).Insert the mounting plate at
the bottom of the filter into
the valve cover.
(2).Hang up the hook at the left
upper side.
(3).Push the upper part in as
indicated in Figure .
Hook
Disposal of the complete unit
Wipe the complete unit with soft cloth twisted dry.
Wipe with neutral detergent if too dirty
Do not wash it directly by water
Alcohol
Petrol Thinner
After washing, dismount the water inlet hose.
Do not store water in the tub for long period. Discharge the water immediately after each using.
Pull off the power plug and hang up the power cord.
Hang up the drain hose.
Wipe off the water drops on the surface and inside the tub with clean soft cloth.
Open the cover of the wash tub and the inner/outer cover of the spin tub for some time (about one hour), then close them.
11
Trouble-shooting Answers to question
If the laundries fall to the outer side of the spin tub
If the laundries fall to the outer side of the spin tub, Please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself.
When the remained water is frozen
Prevent the freezing (be sure to discharge the water completely after
using)
After complete draining, set the "WASH SELECTOR" at "SOFT" or "STANDARD". If it is set at "DRAIN", it will be rather difficult for
the frozen water to melt.
When the water is frozen ,Pour hot water below 50 into the wash tub to soak it completely. Then turn the pulsator with hands gently.
Please confirm the drainage can work normally before next using.
Below 50
2~3L
12
Trouble-shooting Answer to question
(If there's breakdown, please pull off the power plug before checking) The following
phenomena are not breakdowns sometimes. Please confirm again before sending
it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself.
Phenomena The reason
The machine does
not act.
Is there power failure?
Is the power plug loose?
Is the pulsator twisted by foreign materials?
The draining does not work
Is the drain hose frozen?
Is the drain hose blocked by foreign material?
Are there laundries falling to the outer side of
the spin tub?
There's abnormal soundduring washing
Are there hair pin, coins or metal items brought
inside the tub?
There's abnormal sound and violent
vibration during spinning
Is the machine slanting?
Is the gland pressed evenly?
Are there laundries falling to the outer side of the spin tub?
Are the laundries in spin tub too much?
There may be some waterflowing out of the drain hose in the first use of the machine.
It is the water remained in the factory inspection of performance.
13
14
Packing list
Name
User's manual
Water inlet hose
Lint filter
Gland
Twin-tub washing machine
Quantity
One piece
One piece
One piece
One piece
One set
Specification
Water level/Water quantity (about) Maximum/40L Medium/32L Minimum/25L
Injection pressure(MPa ) 0.02
0.2
Rated washing / spinning capacity(kg) 4.0/3.5 (weight of standard dry cloth)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project