AMX RDM-2ZC Installation Sheet
Add to my manuals2 Pages
AMX RDM-2ZC is a high-performance digital dimming module designed for use with electronic fluorescent ballasts, electronic transformers, and incandescent lamps. It offers precise and reliable control over lighting systems, ensuring optimal illumination and energy efficiency.
Key Features and Capabilities:
- Dual 2400W Zero Cross Relay: Enables simultaneous control of two independent lighting circuits with a combined wattage capacity of 2400W.
- Universal Compatibility: Supports a wide range of lighting loads, including non-phase-dependent devices, making it suitable for various applications.
advertisement
The RDM-2ZC Dual Zero Cross Module is a dual 2400 W zero-cross relay built for long term, reliable switching of electronic fluorescent ballasts, electronic transformers and incandescent lamps. It is designed for use with the
RDA series of enclosures, in an AMX Lighting™ modular digital dimming system. The module's 120, 240, and 277 VAC ratings are CE, UL, and C-
UL approved.
Mounting points
Installation Sheet
RDM-2ZC Dual Zero Cross Module
2400 W
• This module may require extra power from the AXlink connection or an external power supply connected to the control card.
Connecting the RDM-2ZC to the AMX Lighting Master
Pin 4 (GND)
Pin 3 (RLY)
Pin 2 (DIM)
Pin 1 (+12 V)
RDM-2ZC 4-pin module connector
Line in (hot)
Load out
High-voltage connections
3 (-)
1 (+)
4-pin plug from RDM series module
NOTE: The 4-pin plugs from the module connector to the 4-pin connector on the master (black plug cover facing up).
Zero cross relay A
FIG. 2 RDM-2ZC connections
Lighting Application Drawing
All neutrals are common to the Neutral block in the enclosure. Provide a separate neutral for each load.
Zero cross relay B
(B) Load
(A) Load
Low-voltage control wiring: 4-pin connector to AMX Lighting master controller
(B) Line in (HOT)
(A) Line in (HOT)
FIG. 1 RDM-2ZC
RDM-2ZC UL and C-UL Ratings
• 120-277 VAC, 2400 W
• 240/277 VAC, 2400 W
Suggested Switched Loads
• Incandescent
• Electronic transformers
• HID ballast
• Electronic and magnetic ballast
Specifications
• Dimensions (HW): 10.00" x 2.75" (25.40 cm x 6.99 cm)
• Non-phase dependant
• Use wires rated at 75°C (167°F)
• Torque terminals to 7 in-lbs. (0.8 N/M)
• Max. wire size: 10 AWG (4 mm²)
• Wire stripping length: 0.28" (7 mm)
• Weight: 2.0 lbs. (0.91 kg)
• BTU/hr: 300
• Control current: 45 mA per relay (90 mA total) @ 12 VDC
Caution: Pre-Installation Notes
• All Class 1 wiring must be connected to proper terminals.
• All control wiring must be connected to proper terminals.
• Disconnect power while installing or connecting the unit.
• Keep top and bottom air vents clear at all times.
• Test loads for shorts before connecting.
• Use low voltage wires with a 300 volt rating or greater.
• Use field installed copper conductors.
• All electrical ratings are for continuous duty.
• For indoor use only.
Circuit breaker panel
FIG. 3 RDM-2ZC wiring configuration
Fluorescent Ballast
Ballast
Load
Neutral
Safety ground
Neutral
Load
Neon lights
(cold-cathode, on/off)
AMX Corporation reserves the right to alter specifications without notice at any time.
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
043-019-2201 8/01 ©2001 AMX Corporation. All rights reserved.
The AMX logo is a trademark of AMX Corporation. AMX Corporation reserves the right to alter specifications without notice at any time.
3000 research drive, richardson, TX 75082 USA • 469.624.8000 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project