English
ET2702I Series
User Manual
English
E8222
April 2013
First Edition
COPYRIGHT INFORMATION
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in
a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for
backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO
EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA,
INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING
FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective
companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE
SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS
ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING
THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Copyright © 2013 ASUSTeK COMPUTER INC. All Rights Reserved.
LIMITATION OF LIABILITY
Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to recover damages from
ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no
more than damages for bodily injury (including death) and damage to real property and tangible personal property; or any other
actual and direct damages resulted from omission or failure of performing legal duties under this Warranty Statement, up to the
listed contract price of each product.
ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this
Warranty Statement.
This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are
collectively responsible.
UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-PARTY CLAIMS AGAINST YOU FOR
DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3) SPECIAL, INCIDENTAL, OR INDIRECT DAMAGES OR FOR
ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR
RESELLER IS INFORMED OF THEIR POSSIBILITY.
SERVICE AND SUPPORT
Visit our multi-language web site at http://support.asus.com
English
Table of Contents
About this manual................................................................................................................................................. 5
Conventions used in this manual........................................................................................................................ 6
Icons............................................................................................................................................................................... 6
Typography.................................................................................................................................................................. 6
Safety information................................................................................................................................................. 7
Setting up your system........................................................................................................................................... 7
Care during use.......................................................................................................................................................... 7
Sound Pressure Warning......................................................................................................................................... 8
TV Tuner (on selected models)............................................................................................................................. 8
Adapter......................................................................................................................................................................... 8
DC Fan Warning.......................................................................................................................................................... 8
ET2702I Series CPU Configurations..................................................................................................................... 8
Package contents................................................................................................................................................... 9
Chapter 1: Hardware Setup
Getting to know your All-in-One PC................................................................................................................ 10
Front view..................................................................................................................................................................... 10
Rear view...................................................................................................................................................................... 12
Side views..................................................................................................................................................................... 15
Chapter 2: Using your All-in-One PC
Positioning your All-in-One PC.......................................................................................................................... 17
Placing on the table or desk.................................................................................................................................. 17
Setting up your All-in-One PC........................................................................................................................... 18
Connecting the wired keyboard and mouse................................................................................................... 18
Connecting the wireless keyboard and mouse.............................................................................................. 19
Turning your All-in-One PC on.............................................................................................................................. 20
Using the Device Share function...................................................................................................................... 21
Device Share Cable Requirement........................................................................................................................ 21
Using the On Screen Display (OSD) Menu.................................................................................................... 22
OSD function instruction........................................................................................................................................ 22
Input signal selection............................................................................................................................................... 23
Gestures........................................................................................................................................................................ 24
Configuring the audio output via an HDMI device.................................................................................... 26
All-in-One PC ET2702I
Table of Contents
English
Chapter 3: Working with Windows® 8
Starting for the first time..................................................................................................................................... 29
Windows® 8 lock screen........................................................................................................................................ 29
Windows® UI............................................................................................................................................................. 30
Start screen.................................................................................................................................................................. 30
Windows® apps.......................................................................................................................................................... 31
Hotspots....................................................................................................................................................................... 31
Working with Windows® apps............................................................................................................................ 34
Launching apps.......................................................................................................................................................... 34
Customizing apps...................................................................................................................................................... 34
Accessing All Apps.................................................................................................................................................... 35
Charms bar................................................................................................................................................................... 36
Snap feature................................................................................................................................................................ 38
Other keyboard shortcuts................................................................................................................................... 39
Turning your All-in-One PC off.......................................................................................................................... 40
Entering the BIOS Setup...................................................................................................................................... 41
Chapter 4: Connecting to the Internet
Wi-Fi connection.................................................................................................................................................... 43
Wired connection................................................................................................................................................... 45
Configuring a dynamic IP/PPPoE network connection............................................................................... 45
Configuring a static IP network connection.................................................................................................... 48
Chapter 5: Recovering your system
Resetting your All-in-One PC............................................................................................................................. 49
Recovering from a system image file.............................................................................................................. 50
Creating a USB recovery drive.............................................................................................................................. 50
Removing everything and reinstalling Windows....................................................................................... 51
Appendices
Notices....................................................................................................................................................................... 53
UL Safety Precaution................................................................................................................................................ 57
All-in-One PC ET2702I
About this manual
English
This manual provides information about the hardware and software features of your All-in-One
PC, organized through the following chapters:
Chapter 1: Hardware Setup
This chapter details the hardware components of your All-in-One PC.
Chapter 2: Using your All-in-One PC
This chapter provides you with information on using your All-in-One PC.
Chapter 3: Working with Windows® 8
This chapter provides an overview of using Windows® 8 in your All-in-One PC.
Chapter 4: Connecting to the Internet
This chapter provides information on connecting your All-in-One PC to a wired or Wi-Fi
network.
Chapter 5: Recovering your system
This chapter provides recovery options for your All-in-One PC.
Appendices
This section includes notices and safety statements for your All-in-One PC.
All-in-One PC ET2702I
Conventions used in this manual
English
To highlight key information in this manual, some text are presented as follows:
IMPORTANT! This message contains vital information that must be followed to complete a task.
NOTE: This message contains additional information and tips that can help complete tasks.
WARNING! This message contains important information that must be followed to keep you safe
while performing tasks and prevent damage to your All-in-One PC's data and components.
Icons
The icons below indicate the devices you can use for completing a series of tasks or procedures
on your All-in-One PC.
Use the touchscreen.
Use the keyboard.
Typography
Bold
= This indicates a menu or an item that must be selected.
Italic
= This indicates sections that you can refer to in this manual.
All illustrations and screenshots in this manual are for reference only. Actual product
specifications and software screen images may vary with territories. Visit the ASUS
website at www.asus.com for the latest information.
All-in-One PC ET2702I
Safety information
English
Your All-in-One PC ET2702I is designed and tested to meet the latest standards of safety for
information technology equipment. However, to ensure your safety, it is important that you
read the following safety instructions.
Setting up your system
•
•
•
•
•
•
Read and follow all instructions in the documentation before you operate your system.
Do not use this product near water or a heated source such as a radiator.
Set up the system on a stable surface.
Openings on the chassis are for ventilation. Do not block or cover these openings. Ensure
that you leave plenty of space around the system for ventilation. Never insert objects of any
kind into the ventilation openings.
Use this product in environments with ambient temperatures between 0˚C and 40˚C.
If you use an extension cord, ensure that the total ampere rating of the devices plugged
into the extension cord does not exceed its ampere rating.
Care during use
•
•
•
•
•
Do not walk on the power cord or allow anything to rest on it.
Do not spill water or any other liquids on your system.
When the system is turned off, a small amount of electrical current still flows. Always
unplug all power, modem, and network cables from the power outlets before cleaning the
system.
The touch screen requires periodic cleaning to achieve the best touch sensitivity. Keep the
screen clean from foreign objects or excessive dust accumulation. To clean the screen:
• Turn off the system and disconnect the power cord from the wall.
• Spray a small amount of a household glass cleaner onto the supplied cleaning cloth
and gently wipe the screen surface.
• Do not spray the cleaner directly on the screen.
• Do not use an abrasive cleaner or a coarse cloth when cleaning the screen.
If you encounter the following technical problems with the product, unplug the power cord
and contact a qualified service technician or your retailer.
• The power cord or plug is damaged.
• Liquid has been spilled into the system.
• The system does not function properly even if you follow the operating instructions.
• The system was dropped or the cabinet is damaged.
• The system performance changes.
All-in-One PC ET2702I
Sound Pressure Warning
English
Excessive sound pressure from earphones or headphones can cause hearing damage or loss.
Adjustment of the volume control as well as the equalizer to settings other than the center
position may increase the earphones or headphones output voltage and the sound pressure
level.
TV Tuner (on selected models)
Note to CATV System Installer—This reminder is provided to call the CATV systems installer’s
attention to Section 820-93 of the National Electric Code, which provides guidelines for
proper grounding and, in particular, specify that the Coaxial cable shield be connected to the
grounding system of the building as close to the point of cable entry as practical.
Adapter
1. Input voltage: 100–240Vac
Input frequency: 50–60Hz
Rating output current: 180W (2.5A)
Rating output voltage: +19.5Vdc/9.23A
2. The socket outlet must be near to the unit and easily accessible.
DC Fan Warning
Please note that the DC fan is a moving part that may cause DANGER. Ensure to keep your
body from the moving fan blades.
ET2702I Series CPU Configurations
i7 4770 @ 3.4 Ghz, Turbo Boost up to 3.9 GHz
i5 4430 @ 3 GHz, Turbo Boost up to 3.2 GHz
All-in-One PC ET2702I
English
Package contents
All-in-One PC ET2702 Series
Keyboard (wired or wireless, optional)
Mouse (wired or wireless, optional)
Quic
k Gu
ide
AC adapter
Remote Control (optional)
Power cord
Quick Start Guide
Warranty Card
KBM USB receiver dongle (optional)
Subwoofer (optional)
Device share cable (optional)
NOTE: The keyboard, mouse, power supply, remote control, and wireless USB receiver dongle
illustrations are for reference only. Actual product specifications may vary with territories.
All-in-One PC ET2702I
Chapter 1: Hardware Setup
English
Getting to know your All-in-One PC
Front view
Webcam LED
Indicates that the built-in webcam is enabled.
Webcam
The built-in webcam with the built-in digital microphone allows you to start video
chats online.
Digital microphone (built-in)
The built-in digital microphone can be used for video conferencing, voice narrations,
audio recordings, and multimedia applications.
10
All-in-One PC ET2702I
English
Remote control receiver
The remote control receiver receives the infrared signal from the remote control.
LCD display
The LCD display features optimal resolution. The touch-enabled panel on some
models also allows you to operate your All-in-One PC using touch screen gestures.
Mode button
Touch to switch the display signal source. When switched to HDMI-in, the All-in-One
PC can be used as a standard desktop LCD monitor.
Volume decrease button
When using the All-in-One PC as a standard desktop LCD monitor, touch this button to
decrease the volume.
MENU button
Touch to display the menu. Touch this button to enter/select the highlighted icon
(function) while the OSD is activated.
Volume increase button
When using the All-in-One PC as a standard desktop LCD monitor, touch this button to
increase the volume.
Audio speakers
The built-in audio speaker allows you to hear audio straight from the All-in-One PC.
The audio features of this All-in-One PC are software-controlled.
Power button
Press this button to turn on your All-in-One PC.
Drive activity indicator
This indicator lights up when your All-in-One is accessing the internal storage drives.
All-in-One PC ET2702I
11
Rear view
English
Antenna Input (optional)
The antenna input is for TV frequency signal and allows for use with the digital TV
antenna or input from subscription television services. The antenna can receive digital
TV. Cable service connection can receive digital TV, analog TV, depending on paid
services.
Subwoofer jack (on selected models)
The proprietary subwoofer jack is used to connect to the ASUS All-in-One PC
subwoofer. The subwoofer allows you to enjoy vibrant bass (low frequency) sounds in
your multimedia applications.
IMPORTANT! The subwoofer jack can ONLY be connected to All-in-One PC subwoofers
or sound devices by ASUS. DO NOT connect other devices to this jack. Doing so may
damage the device.
Kensington® security slot
The Kensington® security slot allows you to secure your All-in-One PC using
Kensington® compatible security products.
12
All-in-One PC ET2702I
English
Cable holder
Use this cable holder to organize your cables behind the All-in-One PC.
Power input
The supplied power adapter converts AC power to DC power for use with this jack.
Power supplied through this jack supplies power to the PC. To prevent damage to the
PC, always use the supplied power adapter.
WARNING! The power adapter may become warm or hot when in use. Do not cover the
adapter and keep it away from your body.
LAN port
The eight-pin RJ-45 LAN port supports a standard Ethernet cable for connection to a
local network.
Thunderbolt™ port (optional)
Use a Thunderbolt™ adapter to connect your All-in-One PC to external devices that
utilize high-resolution display features using Intel® Thunderbolt™ technology.
NOTE: The Thunderbolt™ adapter supports Display Port output and other
Thunderbolt™ devices only. Connect HDMI devices to your All-in-One PC via the
HDMI output port.
IMPORTANT! The devices to be connected should be Thunderbolt-certified for
Windows®. For the latest Thunderbolt-certified devices for Windows���������
®��������
, visit https://
thunderbolttechnology.net/products
NOTE: To ensure that the Thunderbolt-certified device for Windows functions properly,
visit the device vendor’s website.
HDMI input port
This port is for a HDMI (High-Definition Multimedia Interface) connector and is HDCP
compliant for HD DVD, Blu-ray, and other protected content playback.
HDMI output port
This port allows you to connect your All-in-One PC to another HDMI-compatible
device for file sharing or extending your display monitor.
All-in-One PC ET2702I
13
English
USB 2.0 combo with Device Share function for external devices
This USB (Universal Serial Bus) port is compatible with USB 2.0 or USB 1.1 devices such
as keyboards, pointing devices, flash disk drives, external HDDs, speakers, cameras,
and printers.
This port also comes with the Device Share function that allows you to share the
hardware functions of your All-in-One PC with a connected device and vice versa.
NOTE: For more details, refer to the Using the Device Share function in this manual.
IMPORTANT! When using the device share function, connect your keyboard, wireless
dongle, or wireless mouse using this port.
USB 2.0 port with AI Charger II
This USB (Universal Serial Bus) port is compatible with USB 2.0 or USb 1.1 devices such
as keyboards, pointing devices, flash disk drives, external HDDs, speakers, cameras,
and printers.
This port also comes with the AI Charger II function that allows you to quickcharge compatible devices. To enable the AI Charger II on your All-in-One PC, go to
Desktop>AI Suite II>AI Charger II then select Enable.
14
All-in-One PC ET2702I
English
Side views
Memory card reader
This built-in memory card reader supports SD, SDHC, and MMC card formats.
USB 3.0 ports
These USB 3.0 (Universal Serial Bus 3.0) ports provide a transfer rate of up to 5 Gbit/s
and are backward compatible to USB 2.0.
USB 3.0 port with Device Share function
This USB 3.0 (Universal Serial Bus 3.0) port provides a transfer rate of up to 5 Gbit/s and
are backward compatible to USB 2.0.
This port also enables the device share function of your All-in-One PC. Use only the
bundled device share cable that comes with your package to enable this function.
NOTE: For more details, refer to the Using the Device Share function in this manual.
All-in-One PC ET2702I
15
English
Headphone output and S/PDIF output combo jack port
This port allows you to connect your All-in-One PC to amplified speakers or
headphones. You can also use this port to connect your All-in-One PC to S/PDIF (Sony/
Philips Digital Interconnect Format) compliant devices.
Headphone jack
The stereo headphone jack (3.5mm) is used to connect the system’s audio out signal
to headphones. Using this jack automatically disables the built-in speakers.
Microphone jack
The microphone jack is designed to connect to a microphone used for video
conferencing, voice narrations, or simple audio recordings.
Optical disc drive
Your All-in-One PC’s optical drive may support several disc formats such as CDs, DVDs,
recordable discs, or rewritable discs.
Optical disc drive manual eject hole
The manual eject hole is used to eject the drive tray in case the electronic eject button
does not work.
WARNING! Use the manual eject hole only when the electronic eject button does not
work.
Optical disc drive eject button
Press this button to eject the optical drive tray.
16
All-in-One PC ET2702I
English
Chapter 2: Using your All-in-One PC
Positioning your All-in-One PC
Placing on the table or desk
To place on the table or desk:
1. Place your All-in-One PC on a flat surface such as a table or desk.
2. You may orient your All-in-One PC from a -5º up to a 20º angle.
IMPORTANT! Orient the display panel within the given range to avoid damaging your All-in-One
PC.
20O
All-in-One PC ET2702I
-5O
17
Setting up your All-in-One PC
English
Connecting the wired keyboard and mouse
Connect the keyboard and the mouse to the USB port on the rear panel. Y��������������������
ou may also connect
��������
the keyboard and mouse to the USB port on the left side of the panel if the keyboard cable is
not long enough��.
18
All-in-One PC ET2702I
English
Connecting the wireless keyboard and mouse
1. Install batteries to the wireless keyboard and mouse.
2. Connect the wireless dongle for keyboard and mouse to a USB port.
3. You can begin using the wireless keyboard and mouse.
NOTES:
•
Simply reconnect if the wireless keyboard and mouse lose connection. Avoid other
nearby WiFi devices at least 20 cm as they may interfere with the connection.
•
The illustrations above are for reference only. Actual appearances and specifications
(wired or wireless) of the keyboard and mouse may vary by territory.
All-in-One PC ET2702I
19
Turning your All-in-One PC on
English
WARNING! DO NOT connect the AC power cord to an AC outlet prior to connecting the DC plug
to the system. Doing so may damage the AC-DC adapter.
NOTE: For details on turning off your All-in-One PC, refer to the section Turning off your All-in-One
PC under Working with Windows® 8.
20
All-in-One PC ET2702I
Using the Device Share function
English
Using the Device Share function, you can share the display panel, rear USB ports, webcam, and
touch screen features of the All-in-One PC to any other Microsoft Windows®-based devices.
Device Share Cable Requirement
HDMI with Device Share
Device share cable
√
HDMI cable
√
1. Enable the Device Share function under the System Setup menu in the OSD. Refer to the
section of Using the On Screen Display (OSD) Menu on page 24 for details.
2. Connect one end of the bundled device share cable to your laptop, tablet PC, or desktop
PC. Connect the other end of the cable to the USB 3.0 port with Device Share function on
your All-in-One PC.
3. Prepare a male-to-male HDMI cable to enable the device share function between your Alin-One PC and external device. Connect one end of the HDMI cable to your laptop, tablet
PC, or desktop PC. Connect the other end of the cable to the HDMI port of your All-in-One
PC.
4. An Input Select OSD menu appears when you connect the HDMI cable to the rear HDMIinput or Display-input port. Use the Volume Increase ( ) / Decrease ( ) buttons to
select HDMI with Device Share press the MENU button to activate the option.
NOTE:
• The Device Share function supports a Microsoft Windows®-based laptop / desktop PC only.
• By default, your All-in-One PC is set to PC mode (All-in-One PC is the display input source). The
touch screen, webcam and rear USB ports will be controlled by the All-in-One PC even if the
Device Share function is enabled.
• When switching the display input source to HDMI (using your All-in-One PC as a desktop LCD
monitor), the touch screen, webcam and rear USB ports will be controlled by the external laptop /
desktop PC if the Device Share function is enabled.
• When using the Device Share function, it is strongly recommended to connect ONLY a USB
mouse or keyboard to the rear USB ports. External USB storage devices are not recommended.
• The Device Share function can be activated even if your All-in-One PC is not powered-on. If you
power on your All-in-One PC while using the Device Share function, an Input Select OSD menu
will appear for display signal selection.
All-in-One PC ET2702I
21
Using the On Screen Display (OSD) Menu
English
The On Screen Display (OSD) menu appears if you do the following:
•
Activate the OSD via pressing the Menu lock button at the left side of your All-in-One PC,
then press the Menu button at the front panel.
OSD function instruction
To display the OSD menu, press the MENU button on the front panel. To navigate through the
OSD functions or modify OSD settings, press the Menu up or Menu down keys. To activate the
selected function, press the MENU button.
Panel Off
This function allows you to turn off the display panel of the All-in-One PC on. Press the MENU
button to activate this function.
Color
• Brightness: The adjusting range is from 0 to 100.
• Contrast: The adjusting range is from 0 to 100.
• Color Temp.: Contains four color modes including Cool, Normal, Warm, and User mode.
Image
• Sharpness: The adjusting range is from 0 to 100.
• Aspect Control: Adjusts the aspect ratio to “Full” or “OverScan”. This function is configurable
only when you use the All-in-One PC as a standard desktop LCD monitor.
• Auto Adjust: Adjusts the horizontal position (H-Position) and the vertical position
(V-Position) of the image. This function is configurable only when you use the All-in-One PC
as a standard desktop LCD monitor and set the Display-input port as the input source.
Input Select
• PC: Sets the All-in-One PC as the display signal source.
• HDMI with Device Share: Enables the device share feature of your All-in-One PC
22
All-in-One PC ET2702I
System Setup
•
•
•
•
•
Adjusts the horizontal position (H-Position) / vertical position (V-Position) of the OSD
menu.
•
Adjusts the OSD timeout from 10 to 120 seconds.
•
Enables or disables the DDC/CI (Display Data Channel/Command Interface) function.•
English
• OSD Setup:
Information: Shows the monitor information.
Language: Allows you to set the OSD language.
All Reset: Allows you to reset all OSD settings.
Device Share: Turns the device share function on or off.
Input signal selection
An Input Select OSD menu appears when you connect the HDMI or Thunderbolt cable to
the rear HDMI-input or Display-input port. Use the Menu up or Menu down keys to navigate
through the input options and press the MENU button to activate the option. Refer to Input
Select in the previous section for details.
All-in-One PC ET2702I
23
Gestures
English
The gestures allow you to launch programs and access the settings of your All-in-One PC. The
functions can be activated by using the hand gestures to your All-in-One PC’s display panel.
Using gestures
Left edge swipe
Right edge swipe
Swipe from the left edge of the screen to
shuffle your running apps.
Swipe from the right edge of the screen to
launch the charms bar.
Top edge swipe
Finger slide
•
Slide your finger to scroll up and down and
slide your finger to pan the screen left or
right.
•
24
In the Start screen, swipe from the top
edge of the screen to view the All Apps
bar.
In a running app, swipe the from top
edge of the screen to view its menu.
All-in-One PC ET2702I
Zoom in
Bring together your two fingers on the
touch panel.
Spread apart your two fingers on the touch
panel.
Tap and hold
Tap/Double tap
•
•
•
•
To move an app, tap and hold the app
tile and drag it to a new location.
To close an app, tap and hold the top
side of the running app and drag it down
to the bottom of the screen to close it
All-in-One PC ET2702I
English
Zoom out
Tap an app to launch it.
On Desktop mode, double-tap an item to
launch it.
25
English
Configuring the audio output via an HDMI device
If you want to use a high-definition TV as an audio output device, connect it to the Home
Theater PC and follow the steps below to configure the audio settings.
To configure the audio output via an HDMI device:
1. From the Start screen, click Desktop to launch the Desktop Mode.
NOTE: For more details, refer to the section Start Screen under Working with Windows® 8.
2.����������������������������������������������������������
Right-click the Volume Mixer icon on the Windows® taskbar
and click Playback devices.
3. From the Playback screen, select Digital Audio
(HDMI).
4. Click Configure and the Speaker Setup window pops
up.
26
All-in-One PC ET2702I
English
5. Select Stereo and click Next.
6. Tick the Front left and right option, and click Next.
7. Click Finish to exit the speaker setup.
All-in-One PC ET2702I
27
English
28
All-in-One PC ET2702I
English
Chapter 3: Working with Windows® 8
Starting for the first time
When you start your computer for the first time, a series of screens appear to guide you in
configuring the basic settings of your Windows® 8 operating system.
To start for the first time:
1. Press the power button on your All-in-One PC. Wait for a few minutes until the setup
screen appears.
2. Pick a language to use on your All-in-One PC.
3. Carefully read the License Terms. Tick I accept the terms for using Windows then click
Accept.
4. Follow the onscreen instructions to configure the following basic items:
5.
•
Personalize
•
Wireless
•
Settings
•
Sign in to your PC
Once you are done configuring the basic items, a Windows®8 tutorial appears. Watch this
to learn more about Windows®8 functionalities.
6. The Start screen appears after successfully signing in to your user account.
Windows® 8 lock screen
The Windows®8 lock screen may appear when your All-in-One PC enters the Windows®8
operating system. To proceed, tap on the lock screen or press any key on your All-in-One PC's
keyboard.
All-in-One PC ET2702I
29
Windows® UI
English
The Window® User Interface (UI) is the tile-based display used in Windows® 8. It includes the
following features you can use while working on your All-in-One PC.
Start screen
The Start screen appears after successfully signing in to your user account. It helps organize all
the programs and applications you need in just one place.
live tiles
User account
Zoom in/out
button for apps
30
All-in-One PC ET2702I
English
Windows® apps
These are apps pinned on the Start screen and displayed on tiled-format for easy access.
IMPORTANT! A screen resolution of 1024 x 768 pixels or higher is required to run Windows® apps.
NOTE: Some apps require signing in to your Microsoft account before they are fully launched.
Hotspots
Onscreen hotspots allow you to launch programs and access the settings of your All-in-One
PC. The functions in these hotspots can be activated using your mouse.
Hotspots on a running app
All-in-One PC ET2702I
31
Hotspots on the Start screen
English
NOTE: Refer to the next page for the Hotspots’ functions.
32
All-in-One PC ET2702I
Action
upper left corner
Hover your mouse pointer then tap on the recent app’s thumbnail to
revert back to that running app.
English
Hotspot
If you launched more than one app, slide down to show all running
apps.
lower left corner
From a running app screen:
Hover your mouse pointer then tap on the Start screen’s thumbnail to
go back to the Start screen.
NOTE: You can also press the Windows key
to go back to the Start screen.
on your keyboard
From the Start screen:
Hover your mouse pointer then tap on the running app’s thumbnail to
go back to that app.
Hover your mouse pointer then click on the recent app’s thumbnail to
go back to that app.
top
Hover your mouse pointer until it changes to a hand icon. Drag then
drop the app to a new location.
NOTE: This hotspot function only works on a running app or when
you want to use the Snap feature. For more details, refer to Snap feature
under Working with Windows® apps..
upper and lower
right corner
All-in-One PC ET2702I
Hover your mouse pointer to launch the charms bar.
33
Working with Windows® apps
English
Use your All-in-One PC’s touchscreen or keyboard to launch and customize your apps.
Launching apps
Tap an app to launch it.
1. Press
2. Press
twice then use the arrow keys to browse through the apps.
to launch your selected app.
Customizing apps
You can move, resize, or unpin apps from the Start screen using the following steps.
Moving apps
Tap and hold the app tile and drag it to a new location.
Resizing apps
Swipe down the app tile to select and launch its settings bar. Tap
tap
to reduce or
to enlarge an app.
Unpinning apps
Swipe down the app tile to select and launch its settings bar. Tap
an app.
34
to unpin
All-in-One PC ET2702I
English
Closing apps
Tap and hold the top side of the running app then drag it down to the bottom of
the screen to close it.
From the running app’s screen, press
.
Accessing All Apps
Aside from the apps already pinned on your Start screen, you can also open other applications
like the exclusive ASUS Software apps bundled with your All-in-One PC through the Apps
screen.
Launching the Apps screen
Launch the Apps screen using your All-in-One PC's touchscreen or keyboard.
1. Swipe down the app tile to select and launch its settings bar.
2. Tap
to show all installed apps in your All-in-One PC.
From the Start screen, press
press
All-in-One PC ET2702I
to select the All Apps icon
then
.
35
Pinning more apps on the Start screen
English
You can pin more apps on the Start screen using your touchscreen.
1. Swipe down the app tile to select and launch its settings bar.
2. Tap
to pin the selected app to the Start screen.
Charms bar
The charms bar is a toolbar that can be triggered on the right side of your screen. It consists of
several tools that allow you to share applications and provide quick access for customizing the
settings of your All-in-One PC.
Charms bar
Launching the charms bar
NOTE: When called out, the charms bar initially appears as a set of white icons. The image above
shows how the charms bar looks like once activated.
Use your All-in-One PC’s touchscreen or keyboard to launch the charms bar.
Swipe the right edge of the screen.
Press
36
.
All-in-One PC ET2702I
English
Inside the charms bar
Search
This charm allows you to look for files, applications, or programs in your All-inOne PC.
Share
This charm allows you to share applications via social networking sites or email.
Start
This charm reverts the display back to the Start screen. From the Start screen,
you can also use this to revert back to a recently opened app.
Devices
This charm allows you to access and share files with the devices attached to your
All-in-One PC such as an external display or printer.
Settings
This charm allows you to access the PC settings of your All-in-One PC.
All-in-One PC ET2702I
37
Snap feature
English
The Snap feature displays two apps side-by-side, allowing you to work or switch between apps.
IMPORTANT! Ensure that your All-in-One PC’s screen resolution is set to 1366 x 768 pixels or
higher before using the Snap feature.
Snap bar
Using Snap
Perform the following steps to activate Snap using your All-in-One PC’s touchscreen or
keyboard.
1. Launch the app you wish to snap.
2. Hover the mouse point on the top side of your screen.
3. Once the pointer changes to a hand icon, drag then drop the app to the left or
right side of the display panel.
4. Launch another app.
1. Launch an app then
2. Press
.
3. To switch between apps, press
38
.
All-in-One PC ET2702I
Other keyboard shortcuts
\
English
Using the keyboard, you can also use the following shortcuts to help you launch applications
and navigate Windows®8.
Switches between the Start screen and the last running app
Launches the desktop
Launches the Computer window on Desktop mode
Opens the File search pane
Opens the Share pane
Opens the Settings pane
Opens the Devices pane
Activates the Lock screen
Minimizes the Internet Explorer window
Opens the Second screen pane
Opens the Apps search pane
Opens the Run window
All-in-One PC ET2702I
39
English
Opens Ease of Access Center
Opens the Settings search pane
Opens a menu box of Windows tools
Launches the magnifier icon and zooms in your screen
Zooms out your screen
Opens the Narrator Settings
Enables the print screen function
Turning your All-in-One PC off
Do either of the following to shut down your All-in-One PC:
40
the charms bar then tap
> Shut down to do a normal
•
Tap from
shutdown.
•
From the log-in screen, tap
•
If your All-in-One PC is unresponsive, press and hold the power button for at
least four (4) seconds until your All-in-One PC turns off.
> Shut down.
All-in-One PC ET2702I
Entering the BIOS Setup
English
BIOS (Basic Input and Output System) stores system hardware settings that are needed for
system startup in the All-in-One PC.
In normal circumstances, the default BIOS settings apply to most conditions to ensure optimal
performance. Do not change the default BIOS settings except in the following circumstances:
•
•
An error message appears on the screen during the system bootup and requests you to run
the BIOS Setup.
You have installed a new system component that requires further BIOS settings or update.
WARNING! Inappropriate BIOS settings may result to instability or boot failure. We strongly
recommend that you change the BIOS settings only with the help of a trained service personnel.
Quickly enter the BIOS
Windows® 8 boot time is quite fast, so we developed these three ways for you to quickly access
the BIOS:
•
•
•
When your All-in-One PC is off, press the power button for at least four (4) seconds to access
the BIOS directly.
Press the power button for at least four (4) seconds to shut down your All-in-One PC, then
press the power button again to turn your All-in-One PC back on, and press <F2> during
POST.
When your All-in-One PC is off, disconnect the power cord from your All-in-One PC’s power
connector. Reconnect the power cord and press the power button to turn on your All-inOne PC. Press <F2> during POST.
NOTE: POST (Power-On Self Test) is a series of software controlled diagnostic tests that run when
you turn on your All-in-One PC.
All-in-One PC ET2702I
41
English
42
All-in-One PC ET2702I
English
Chapter 4: Connecting to the Internet
Access emails, surf the Internet, and share applications via social networking sites on or from
your All-in-One PC using wireless/Wi-Fi or wired connection.
Wi-Fi connection
1. Launch the charms bar from the Start screen or from any application mode.
NOTE: For details, refer to the section charms bar under Working with Windows® apps.
Charm Bar
2. From the charms bar, select Settings and click the network icon
All-in-One PC ET2702I
.
43
3. Select the wireless network that you want to connect to from the list.
English
4. Click Connect.
NOTE: You may be prompted to enter a security key to connect to a secured wireless network.
44
All-in-One PC ET2702I
Wired connection
English
1. Use a network (RJ-45) cable to connect your All-in-One PC to a DSL/cable modem or a
local area network (LAN).
2. Turn on your computer.
3. Configure the necessary Internet connection settings.
NOTES:
•
For more details, refer to the sections Configuring a dynamic IP/PPPoE network connection
or Configuring a static IP network connection.
•
Contact your Internet Service Provider (ISP) for details or assistance in setting up your
Internet connection.
Configuring a dynamic IP/PPPoE network connection
To configure a dynamic IP/PPPoE or static IP network connection:
1. From the Start screen, click Desktop to launch the Desktop mode.
All-in-One PC ET2702I
45
English
2. From the Windows® taskbar, right-click the network icon
Sharing Center.
and click Open Network and
3. From the Open Network and Sharing Center screen, click Change Adapter settings.
4. Right-click on your LAN and select Properties.
5. Click Internet Protocol Version 4(TCP/IPv4) and click
Properties.
6. Click Obtain an IP address automatically and click OK.
NOTE: Continue to the next steps if you are using PPPoE connection.
46
All-in-One PC ET2702I
English
7. Return to the Network and Sharing Center and
then click Set up a new connection or network.
8. Select Connect to the Internet and click Next.
9. Select Broadband (PPPoE) and click Next.
10. Enter your Username, Password, and Connection
name. Click Connect.
11. Click Close to finish the configuration.
12. Click the network icon in the taskbar and click the
connection you just created.
13. Enter your user name and password. Click Connect to
connect to the Internet.
All-in-One PC ET2702I
47
Configuring a static IP network connection
English
To configure a static IP network connection:
1. Repeat steps 1 to 4 of the previous section Configuring a
dynamic IP/PPPoE network connection.
2
Click Use the following IP address.
3. Enter the IP address, Subnet mask and Gateway from your
service provider.
4. If needed, enter the preferred DNS Server address and
alternative address.
5. When done, click OK.
48
All-in-One PC ET2702I
English
Chapter 5: Recovering your system
Resetting your All-in-One PC
The Reset your PC option restores your PC to its factory default settings.
IMPORTANT! Back up all your data before using this option.
To reset your All-in-One PC:
1. Press <F9> during bootup.
IMPORTANT! To go through POST, follow any of the ways described in the section Quickly enter
the BIOS in Chapter 3.
2. From the screen, click Troubleshoot.
3. Select Reset your PC.
4. Click Next.
5. Select Only the drive where the Windows is installed.
6. Select Just remove my files.
7. Click Reset.
All-in-One PC ET2702I
49
Recovering from a system image file
English
You can create a USB recovery drive and use this to recover your All-in-One PC’s settings.
Creating a USB recovery drive
WARNING! All files on your USB storage device will be permanently deleted during the process.
Before you proceed, ensure that you back up all your important data.
To create a USB recovery drive:
1. Launch the Control Panel from the All Apps screen.
NOTE: For details, refer to Launching the All Apps screen under Working with Windows® apps.
2. From the Control Panel’s System and Security, click Find and fix problems.
3. Click Recovery > Create a recovery drive.
4. Click Next.
5. Select the USB storage device where you want to
copy the recovery files.
6. Click Next.
50
All-in-One PC ET2702I
English
7. Click Create. Wait for a while for the process to
complete.
8. When the process is completed, click Finish.
Removing everything and reinstalling Windows
Restoring your All-in-One PC to its original factory settings can be done using the Remove
everything and reinstall option in PC Settings. Refer to the steps below to use this option.
IMPORTANT!
Back up all your data before using this option.
NOTE: This process may take a while to complete.
1. Launch the charms bar.
2. Click Settings > Change PC Settings > General.
3. Scroll down to view the Remove everything and reinstall Windows option. Under this
option, click Get Started.
4. Follow the onscreen instructions to complete the reinstallation and reset process.
All-in-One PC ET2702I
51
English
52
All-in-One PC ET2702I
English
Notices
Appendices
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of
Chemicals) regulatory framework, we publish the chemical substances in our products at ASUS
REACH website at http://csr.asus.com/english/REACH.htm
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards
for protecting our environment. We believe in providing solutions for you to be able to
responsibly recycle our products, batteries, other components, as well as the packaging
materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling
information in different regions.
COATING NOTICE
IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is
applied to insulate the device except on the areas where the I/O ports are located.
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance
with manufacturer’s instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
All-in-One PC ET2702I
53
•
English
•
Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications not expressly approved by the guarantee of this
device could void the user’s authority to operate the equipment.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and
the antenna(s) used for this transmitter must be installed to provide a separation distance of
at least 20 cm from all persons and must not be co-located or operating in conjunction with
any other antenna or transmitter. End-users and installers must be provided with antenna
installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
This class B digital apparatus complies with Canadian ICES-003.
IC Radiation Exposure Statement for Canada
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. To maintain compliance with IC RF exposure compliance requirements, please
avoid direct contact to the transmitting antenna during transmitting. End users must follow
the specific operating instructions for satisfying RF exposure compliance.
Operation is subject to the following two conditions:
•
•
54
This device may not cause interference and
This device must accept any interference, including interference that may cause undesired
operation of the device.
All-in-One PC ET2702I
Declaration of Conformity (R&TTE directive 1999/5/EC)
•
•
•
•
•
•
•
English
The following items were completed and are considered relevant and sufficient:
Essential requirements as in [Article 3]
Protection requirements for health and safety as in [Article 3.1a]
Testing for electric safety according to [EN 60950]
Protection requirements for electromagnetic compatibility in [Article 3.1b]
Testing for electromagnetic compatibility in [EN 301 489-1] & [EN 301 489-17]
Effective use of the radio spectrum as in [Article 3.2]
Radio test suites according to [EN 300 328-2]
CE Mark Warning
This is a Class B product, in a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
CE marking for devices without wireless LAN/Bluetooth
The shipped version of this device complies with the requirements of the EEC directives
2004/108/EC “Electromagnetic compatibility” and 2006/95/EC “Low voltage directive”.
/
CE marking for devices with wireless LAN/ Bluetooth
This equipment complies with the requirements of Directive 1999/5/EC of the European
Parliament and Commission from 9 March, 1999 governing Radio and Telecommunications
Equipment and mutual recognition of conformity.
is for class II device.
Wireless Operation Channel for Different Domains
N. America
2.412-2.462 GHz
Ch01 through CH11
Japan
2.412-2.484 GHz
Ch01 through Ch14
Europe ETSI
2.412-2.472 GHz
Ch01 through Ch13
All-in-One PC ET2702I
55
English
NO DISASSEMBLY
The warranty does not apply to the products that
have been disassembled by users
Lithium-Ion Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
No Exposure to Liquids
DO NOT expose to or use near liquids, rain, or moisture. This product is not
waterproof or oil-proof.
This symbol of the crossed out wheeled bin indicates that the product (electrical, electronic
equipment, and mercury-containing button cell battery) should not be placed in municipal
waste. Check local regulations for disposal of electronic products.
DO NOT throw the battery in municipal waste. The symbol of the crossed out wheeled bin
indicates that the battery should not be placed in municipal waste.
56
All-in-One PC ET2702I
English
Global Environmental Regulation Compliance and Declaration
ASUS follows the green design concept to design and manufacture our products, and
makes sure that each stage of the product life cycle of ASUS product is in line with global
environmental regulations. In addition, ASUS disclose the relevant information based on
regulation requirements.
Please refer to http://csr.asus.com/english/Compliance.htm for information disclosure based
on regulation requirements ASUS is complied with:
Japan JIS-C-0950 Material Declarations
EU REACH SVHC
Korea RoHS
Swiss Energy Laws
UL Safety Precaution
To meet safety requirements, the All-in-One PC must be mounted to a bracket which
guarantees the necessary stability considering the weight of the All-in-One PC. The All-in-One
PC shall only be mounted and used with UL listed mounting adapters and brackets (e.g. VESA).
All-in-One PC ET2702I
57
ENERGY STAR complied product
English
ENERGY STAR is a joint program of the U.S. Environmental Protection Agency
and the U.S. Department of Energy helping us all save money and protect
the environment through energy efficient products and practices.
on the keyboard.
All ASUS products with the ENERGY STAR logo comply with the ENERGY STAR
standard, and the power management feature is enabled by default. The
monitor and computer are automatically set to sleep after 15 and 30 minutes
of user inactivity. To wake your computer, click the mouse or press any key
Please visit http://www.energy.gov/powermanagement for detail information on power
management and its benefits to the environment. In addition, please visit http://www.
energystar.gov for detail information on the ENERGY STAR joint program.
NOTE: ENERGY STAR is NOT supported on Freedos and Linux-based products.
58
All-in-One PC ET2702I
English
Manufacturer
Authorised
representative in
Europe
All-in-One PC ET2702I
ASUSTeK Computer Inc.
Tel:
+886-2-2894-3447
Address: 4F, No. 150, LI-TE RD., PEITOU, TAIPEI 112, TAIWAN R.O.C
ASUSTeK Computer GmbH
Address: HARKORT STR. 21-23, 40880 RATINGEN, GERMANY
59
English
60
All-in-One PC ET2702I