advertisement
E8997
First Edition
February 2014
Notebook PC
E-Manual
COPYRIGHT INFORMATION
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES
OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
(INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION
OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES
ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL
USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE
CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY
ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND
SOFTWARE DESCRIBED IN IT.
Copyright © 2014 ASUSTeK COMPUTER INC. All Rights Reserved.
LIMITATION OF LIABILITY
Circumstances may arise where because of a default on ASUS’ part or other liability, you are entitled to recover damages from ASUS. In each such instance, regardless of the basis on which you are entitled to claim damages from ASUS, ASUS is liable for no more than damages for bodily injury (including death) and damage to real property and tangible personal property; or any other actual and direct damages resulted from omission or failure of performing legal duties under this Warranty Statement, up to the listed contract price of each product.
ASUS will only be responsible for or indemnify you for loss, damages or claims based in contract, tort or infringement under this Warranty Statement.
This limit also applies to ASUS’ suppliers and its reseller. It is the maximum for which ASUS, its suppliers, and your reseller are collectively responsible.
UNDER NO CIRCUMSTANCES IS ASUS LIABLE FOR ANY OF THE FOLLOWING: (1) THIRD-PARTY CLAIMS
AGAINST YOU FOR DAMAGES; (2) LOSS OF, OR DAMAGE TO, YOUR RECORDS OR DATA; OR (3) SPECIAL,
INCIDENTAL, OR INDIRECT DAMAGES OR FOR ANY ECONOMIC CONSEQUENTIAL DAMAGES (INCLUDING
LOST PROFITS OR SAVINGS), EVEN IF ASUS, ITS SUPPLIERS OR YOUR RESELLER IS INFORMED OF THEIR
POSSIBILITY.
SERVICE AND SUPPORT
Visit our multi-language web site at http://support.asus.com
2 Notebook PC E-Manual
Table of Contents
Chapter 1: Hardware Setup
Chapter 2: Using your Notebook PC
Notebook PC E-Manual 3
4
Chapter 3: Working with Windows® 8.1
Configuring a dynamic IP/PPPoE network connection ....................................64
Chapter 4: Power-On Self-Test (POST)
Using POST to access BIOS and Troubleshoot......................................................72
Notebook PC E-Manual
Tips and FAQs
Appendices
DVD-ROM Drive Information (on selected models) ...........................................96
Blu-ray ROM Drive Information (on selected models).......................................98
Federal Communications Commission Interference Statement ...................101
FCC Radio Frequency (RF) Exposure Caution Statement .................................102
Declaration of Conformity (R&TTE directive 1999/5/EC) ..................................103
IC Radiation Exposure Statement for Canada ......................................................104
Déclaration d’Industrie Canada relative à l’exposition aux ondes radio ...105
Wireless Operation Channel for Different Domains ...........................................106
Notebook PC E-Manual 5
Nordic Lithium Cautions (for lithium-ion batteries) ...........................................110
CTR 21 Approval (for Notebook PC with built-in Modem) ..............................112
Global Environmental Regulation Compliance and Declaration ..................115
6 Notebook PC E-Manual
About this manual
This manual provides information about the hardware and software features of your Notebook PC, organized through the following chapters:
Chapter 1: Hardware Setup
This chapter details the hardware components of your Notebook
PC.
Chapter 2: Using your Notebook PC
This chapter shows you how to use the different parts of your
Notebook PC.
Chapter 3: Working with Windows® 8.1
This chapter provides an overview of using Windows® 8.1 in your
Notebook PC.
Chapter 4: Power-On Self-Test (POST)
This chapter shows you how to use POST to change the settings of your Notebook PC.
Tips and FAQs
This section presents some recommended tips, hardware FAQs, and software FAQs you can refer to for maintaining and fixing common issues with your Notebook PC.
Appendices
This section includes notices and safety statements for your
Notebook PC.
Notebook PC E-Manual 7
8
Conventions used in this manual
To highlight key information in this manual, some text are presented as follows:
IMPORTANT! This message contains vital information that must be followed to complete a task.
NOTE: This message contains additional information and tips that can help complete tasks.
WARNING! This message contains important information that must be followed to keep you safe while performing tasks and prevent damage to your Notebook PC's data and components.
Icons
The icons below indicate the devices you can use for completing a series of tasks or procedures on your Notebook PC.
= Use the touchpad.
= Use the keyboard.
Typography
Bold = This indicates a menu or an item that must be selected.
Italic = This indicates sections that you can refer to in this manual.
Notebook PC E-Manual
Safety precautions
Using your Notebook PC
This Notebook PC should only be used in environments with ambient temperatures between
5°C (41°F) and 35°C (95°F).
Refer to the rating label on the bottom of your
Notebook PC and ensure that your power adapter complies with this rating.
Do not leave your Notebook PC on your lap or near any part of your body to prevent discomfort or injury from heat exposure.
Do not use damaged power cords, accessories, and other peripherals with your Notebook PC.
While powered on, ensure that you do not carry or cover your Notebook PC with any materials that can reduce air circulation.
Do not place your Notebook PC on uneven or unstable work surfaces.
Notebook PC E-Manual
You can send your Notebook PC through x-ray machines (used on items placed on conveyor belts), but do not expose them to magnetic detectors and wands.
Contact your airline provider to learn about related inflight services that can be used and restrictions that must be followed when using your Notebook
PC in-flight.
9
10
Caring for your Notebook PC
Disconnect the AC power and remove the battery pack (if applicable) before cleaning your Notebook
PC. Use a clean cellulose sponge or chamois cloth dampened with a solution of nonabrasive detergent and a few drops of warm water. Remove any extra moisture from your Notebook PC using a dry cloth.
Do not use strong solvents such as thinners, benzene, or other chemicals on or near your
Notebook PC.
Do not place objects on top of your Notebook PC.
Do not expose your Notebook PC to strong magnetic or electrical fields.
Do not use or expose your Notebook PC near liquids, rain, or moisture.
Do not expose your Notebook PC to dusty environments.
Do not use your Notebook PC near gas leaks.
Notebook PC E-Manual
Proper disposal
Do not throw your Notebook PC in municipal waste.
This product has been designed to enable proper reuse of parts and recycling. The symbol of the crossed out wheeled bin indicates that the product
(electrical, electronic equipment and mercurycontaining button cell battery) should not be placed in municipal waste. Check local regulations for disposal of electronic products.
Do not throw the battery in municipal waste. The symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste.
Notebook PC E-Manual 11
12 Notebook PC E-Manual
Chapter 1:
Hardware Setup
Notebook PC E-Manual 13
Getting to know your Notebook PC
Top View
NOTE: The keyboard's layout may vary per region or country. The
Notebook view may also vary in appearance depending on the Notebook
PC model.
14 Notebook PC E-Manual
Camera
The built-in camera allows you to take pictures or record videos using your Notebook PC.
Camera indicator
The camera indicator lights up when the built-in camera is in use.
Microphone
The built-in microphone can be used for video conferencing, voice narrations, or simple audio recording.
Display panel
This high-definition display panel provides excellent viewing features for photos, videos, and other multimedia files on your
Notebook PC.
Power button
Press the power button to turn your Notebook PC on or off. You can also use the power button to put your Notebook PC to sleep or hibernate mode and wake it up from sleep or hibernate mode.
In the event that your Notebook PC becomes unresponsive, press and hold the power button for about four (4) seconds until your Notebook PC shuts down.
Capital lock indicator
This indicator lights up when the capital lock function is activated. Using capital lock allows you to type capitalized letters
(such as A, B, C) using your Notebook PC’s keyboard.
Notebook PC E-Manual 15
16
Keyboard
The keyboard provides full-sized QWERTY keys with a comfortable travel depth for typing. It also enables you to use the function keys, allows quick access to Windows®, and controls other multimedia functions.
NOTE: The keyboard layout differs by model or territory.
Touchpad
The touchpad allows the use of multi-gestures to navigate onscreen, providing an intuitive user experience. It also simulates the functions of a regular mouse.
NOTE: For more details, refer to the Using touchpad gestures section in this manual.
Fingerprint sensor
This built-in fingerprint sensor captures your fingerprint and uses it as biometric authentication for logging on to your Notebook
PC’s system and other programs inside Windows® 8.1.
NOTE: For more details, refer to the ASUS Fingerprint section in this manual.
Notebook PC E-Manual
Bottom
NOTE: The bottom side may vary in appearance depending on model.
WARNING! The bottom of the Notebook PC can get warm to hot while in use or while charging the battery pack. When working on your Notebook
PC, do not place it on surfaces that can block the vents.
IMPORTANT! Battery time varies by usage and by the specifications for this Notebook PC. The battery pack cannot be disassembled.
Notebook PC E-Manual 17
18
Battery pack
The battery pack is automatically charged when your Notebook
PC is connected to a power source. When charged, the battery pack supplies power to your Notebook PC.
Spring battery lock
The spring battery lock automatically locks the battery pack in place once it is inserted into the battery slot.
IMPORTANT! This lock should be held in an unlocked position when removing the battery pack.
Audio speakers
The built-in audio speaker allows you to hear audio straight from the Notebook PC. The audio features of this Notebook PC are software-controlled.
Manual battery lock
The manual battery lock is used to keep the battery pack secured. This lock should be manually moved to a locked or unlocked position to insert or remove the battery pack.
Air vents
The air vents allow cool air to enter and warm air to exit the
Notebook PC.
WARNING! Ensure that paper, books, clothing, cables, or other objects do not block any of the air vents or else overheating may occur.
Notebook PC E-Manual
Right Side
Headphone output/microphone input combo jack port
This port allows you to connect your Notebook PC to amplified speakers or headphones. You can also use this port to connect your Notebook PC to an external microphone.
USB 2.0 ports
These USB (Universal Serial Bus) ports are compatible with USB
2.0 or USB 1.1 devices such as keyboards, pointing devices, flash disk drives, external HDDs, speakers, cameras and printers.
Optical drive
Your Notebook PC’s optical drive may support several disc formats such as CDs, DVDs, recordable discs, or rewritable discs.
Optical disc drive eject button
Press this button to eject the optical drive tray.
Optical disc drive manual eject hole
The manual eject hole is used to eject the drive tray in case the electronic eject button does not work.
WARNING! Use the manual eject hole only when the electronic eject button does not work.
NOTE: For more details, refer to the Using the optical drive section in this manual.
Notebook PC E-Manual 19
Left Side
Kensington® security slot
The Kensington® security slot allows you to secure your
Notebook PC using Kensington® compatible Notebook PC security products.
Power (DC) input port
Insert the bundled power adapter into this port to charge the battery pack and supply power to your Notebook PC.
WARNING! The adapter may become warm to hot while in use.
Do not cover the adapter and keep it away from your body while it is connected to a power source.
20
IMPORTANT! Use only the bundled power adapter to charge the battery pack and supply power to your Notebook PC.
Air vents
The air vents allow cool air to enter and warm air to exit the
Notebook PC.
WARNING! Ensure that paper, books, clothing, cables, or other objects do not block any of the air vents or else overheating may occur.
Notebook PC E-Manual
VGA port
This port allows you to connect your Notebook PC to an external display.
LAN port
Insert the network cable into this port to connect to a local area network.
HDMI port
This port is for the HDMI (High-Definition Multimedia Interface) connector and is HDCP compliant for HD DVD, Blu-ray, and other protected content playback.
USB 3.0 port
This USB (Universal Serial Bus) 3.0 port provides a transfer rate of up to 5 Gbit/s and is backward compatible to USB 2.0.
USB 3.0 port with USB Charger+
This USB 3.0 (Universal Serial Bus 3.0) port provides a transfer rate of up to 5 Gbit/s and is backward compatible to USB 2.0.
The icon indicates this port’s USB Charger+ feature which allows you to quick-charge mobile devices even while your
Notebook PC has been turned off.
NOTE: For more details, refer to the USB Charger+ section in this manual.
Notebook PC E-Manual 21
Front Side
Memory card reader
This Notebook PC has a built-in memory card reader slot that supports MMC and SD card formats.
Status indicators
The status indicators help identify the current hardware status of your Notebook PC.
Power indicator
The power indicator lights up when the Notebook PC is turned on and blinks slowly when the Notebook PC is in sleep mode.
Two-color battery charge indicator
The two-color LED provides a visual indication of the battery’s charge status. Refer to the following table for details:
22 Notebook PC E-Manual
Color
Solid Green
Status
The Notebook PC is plugged to a power source and the battery power is between 95% and
100%.
Solid Orange The Notebook PC is plugged to a power source, charging its battery, and the battery power is less than 95%.
Blinking Orange The Notebook PC is running on battery mode and the battery power is less than 10%.
Lights off The Notebook PC is running on battery mode and the battery power is between 10% to 100%.
Drive activity indicator
This indicator lights up when your Notebook PC is accessing the internal storage drives.
Bluetooth / Wireless indicator
This indicator lights up when your Notebook PC’s wireless function (Bluetooth or Wi-Fi) is enabled.
Notebook PC E-Manual 23
24 Notebook PC E-Manual
Chapter 2:
Using your Notebook PC
Notebook PC E-Manual 25
Getting started
Charge your Notebook PC.
A. Connect the AC power cord to the AC/DC adapter.
B. Plug the AC power adapter into a 100V~240V power source.
C. Connect the DC power connector into your Notebook PC’s power
(DC) input.
Charge the Notebook PC for 3 hours before using it in battery mode for the first time.
NOTE: The power adapter may vary in appearance, depending on models and your region.
26
IMPORTANT!
Power adapter information:
• Input voltage: 100-240Vac
• Input frequency: 50-60Hz
• Rating output current: 3.42A (65W)
• Rating output voltage: 19V
Notebook PC E-Manual
IMPORTANT!
• Locate the input/output rating label on your Notebook PC and ensure that it matches the input/output rating information on your power adapter. Some Notebook PC models may have multiple rating output currents based on the available SKU.
• Ensure that your Notebook PC is connected to the power adapter before turning it on for the first time. We strongly recommend that you use a grounded wall socket while using your Notebook PC on power adapter mode.
• The socket outlet must be easily accessible and near your Notebook
PC.
• To disconnect your Notebook PC from its main power supply, unplug your Notebook PC from the power socket.
WARNING!
Read the following precautions for your Notebook PC’s battery.
• The battery used in this device may present a risk of fire or chemical burn if removed or disassembled.
• Follow the warning labels for your personal safety.
• Risk of explosion if battery is replaced by an incorrect type.
• Do not dispose of in fire.
• Never attempt to short-circuit your Notebook PC’s battery.
• Never attempt to dissamble and reassemble the battery.
• Discontinue usage if leakage is found.
• The battery and its components must be recycled or disposed of properly.
• Keep the battery and other small components away from children.
Notebook PC E-Manual 27
Lift to open the display panel.
Press the power button.
28 Notebook PC E-Manual
Gestures for the touchpad
Gestures allow you to launch programs and access the settings of your
Notebook PC. Refer to the following illustrations when using hand gestures on your touchpad.
Moving the pointer
You can tap or click anywhere on the touchpad to activate its pointer, then slide your finger on the touchpad to move the pointer onscreen.
Slide horizontally
Slide vertically
Slide diagonally
Notebook PC E-Manual 29
One-finger gestures
Left-click Right-click
•
•
In the Start screen, click an app to launch it.
•
In Desktop mode, doubleclick an application to launch it.
•
In the Start screen, click an app to select it and launch the settings bar. You can also press this button to launch the All Apps bar.
In Desktop mode, use this button to open the rightclick menu.
30 Notebook PC E-Manual
Tap/Double tap
•
•
In the Start screen, tap an app to launch it.
In Desktop mode, double-tap an application to launch it.
Drag and drop
Double-tap an item, then slide the same finger without lifting it off the touchpad. To drop the item to its new location, lift your finger from the touchpad.
Notebook PC E-Manual 31
Top edge swipe
• In the Start screen, swipe from the top edge to launch the All
Apps bar.
In a running app, swipe from the top edge to view its menu.
•
Left edge swipe Right edge swipe
Swipe from the left edge to shuffle your running apps.
Swipe the right edge to launch the
Charm bar.
32 Notebook PC E-Manual
Two-finger gestures
Two-finger scroll (up/down) Two-finger scroll (left/right)
Slide two fingers to scroll up or down.
Zoom out
Slide two fingers to scroll left or right.
Zoom in
Bring together your two fingers on the touchpad.
Spread apart your two fingers on the touchpad.
Drag and drop
Select an item then press and hold the left button. Using your other finger, slide down the touchpad to drag and drop the item to a new location.
Notebook PC E-Manual 33
Using ASUS Smart Gesture
The ASUS Smart Gesture app of your Notebook PC allows you to enable other touchpad gestures or disable selected gestures depending on your preference.
Enabling the rotate gesture
1. From the taskbar on your Desktop, click .
2. Double-click the icon to launch the ASUS Smart Gesture app.
34 Notebook PC E-Manual
3. In the ASUS Smart Gesture window, tick Rotate
4. Click Apply to save the changes then OK to exit the ASUS Smart
Gesture window.
Notebook PC E-Manual 35
Enabling the three-finger gestures
1. From the taskbar on your Desktop, click .
2. Double-click the icon to launch the ASUS Smart Gesture app.
36 Notebook PC E-Manual
3. In the ASUS Smart Gesture window, tick the gestures you would like to enable under Three Fingers
4. Click Apply to save the changes then OK to exit the ASUS Smart
Gesture window.
Notebook PC E-Manual 37
Using the rotate and three-finger gestures
Rotate Swipe left or swipe right
With one finger steady on the touchpad, rotate another finger clockwise or counterclockwise.
Swipe three fingers left or right to navigate pages.
Swipe up Swipe down
Swipe three fingers upward to show all running applications.
Swipe three fingers downward to show the Desktop mode.
38 Notebook PC E-Manual
Using the keyboard
Function keys
The function keys on your Notebook PC’s keyboard can trigger the following commands:
Puts the Notebook PC into Sleep mode
Turns Airplane mode on or off
NOTE: When enabled, the Airplane mode disables all wireless connectivity.
Decreases display brightness
Increases display brightness
Turns the display panel off
Activates the second screen
NOTE: Ensure that the second display is connected to your Notebook PC.
Enables or disables the touchpad
Turns the speaker on or off
Notebook PC E-Manual 39
Turns the speaker volume down
Turns the speaker volume up
Windows® 8.1 keys
There are two special Windows® keys on your Notebook PC’s keyboard used as below:
Press this key to go back to the Start screen. If you are already in the Start screen, press this key to go back to the last app you opened.
Press this key to simulate the right-click functions.
Keyboard as numeric keypad
This Notebook PC comes with 15 select keys that you can also use for numeric input.
40
Press to toggle between using these keys as number keys or as their original keyboard function.
Notebook PC E-Manual
Chapter 3:
Working with Windows® 8.1
Notebook PC E-Manual 41
Starting for the first time
When you start your computer for the first time, a series of screens appear to guide you in configuring your Windows® 8.1 operating system.
To start your Notebook PC for the first time:
1. Press the power button on your Notebook PC. Wait for a few minutes until the setup screen appears.
2. From the setup screen, pick your region and a language to use on your Notebook PC.
3. Carefully read the License Terms. Select I accept.
4. Follow the onscreen instructions to configure the following basic items:
• Personalize
• Get online
• Settings
• Your account
5. After configuring the basic items, Windows® 8.1 proceeds to install your apps and preferred settings. Ensure that your
Notebook PC is kept powered on during the setup process.
6. Once the setup process is complete, the Start screen appears.
42 Notebook PC E-Manual
Windows
®
UI
Windows® 8.1 comes with a tile-based user interface (UI) which allows you to organize and easily access Windows® apps from the Start screen.
It also includes the following features that you can use while working on your Notebook PC.
Start screen
The Start screen appears after successfully signing in to your user account. It helps organize all the applications you need in just one place.
Windows® Apps
These are apps pinned on the Start screen and displayed on tiled-format for easy access.
NOTE: Some apps require signing in to your Microsoft account before they are fully launched.
Notebook PC E-Manual 43
Hotspots
Onscreen hotspots allow you to launch programs and access the settings of your Notebook PC. The functions in these hotspots can be activated using the touchpad.
Hotspots on a running app
Hotspots on the Start screen
44 Notebook PC E-Manual
Hotspot upper left corner lower left corner
Action
Hover your mouse pointer on the upper left corner then tap/click on the recent app’s thumbnail to revert back to that running app.
If you launched more than one app, slide down to show all running apps.
From a running app screen:
Hover your mouse pointer on the lower left corner then tap/click to go back to the
Start screen.
NOTE: You can also press the Windows key
on your keyboard to go back to the
Start screen.
From the Start screen:
Hover your mouse pointer on the lower left corner then tap/click to go back to that app.
Notebook PC E-Manual 45
Hotspot top side
Action
Hover your mouse pointer on the top side until it changes to a hand icon. Drag then drop the app to a new location.
NOTE: This hotspot function only works on a running app or when you want to use the
Snap feature. For more details, refer to the
Snap feature under Working with Windows®
apps.
upper or lower right corner
Hover your mouse pointer on the upper or lower right corner to launch the Charms bar.
46 Notebook PC E-Manual
Start button
Windows® 8.1 features the Start button which allows you to switch between the two most recent apps that you opened. The Start button may be accessed from the Start screen, while on Desktop mode, and on any app that is currently open onscreen.
Start button on the Start screen
NOTE: The actual color of your Start button varies depending on the display settings you chose for your Start screen.
Hover your mouse pointer over the left corner of your Start screen or any opened app to call out the Start button.
Notebook PC E-Manual 47
Start button on Desktop mode
Context menu
The context menu appears as a box filled with quick access to some of the programs inside Windows® 8.1 when you right-click on the Start button.
The context menu also includes the following shut down options for your Notebook PC: sign out, sleep, shut down, restart.
48 Notebook PC E-Manual
Customizing your Start screen
Windows® 8.1 also enables you to customize your Start screen, allowing you to boot directly to the Desktop mode and customize the arrangement of your apps onscreen.
To customize the settings of your Start screen:
1. Launch the Desktop.
2. Right-click anywhere on the taskbar, except on the
Start button, to launch the pop-up window.
Properties then select the Navigation tab to tick the Navigation and Start screen options you want to use.
Notebook PC E-Manual 49
Working with Windows
®
apps
Use your Notebook PC’s touchpad, or keyboard to launch, customize, and close apps.
Launching apps
Position your mouse pointer over the app then left-click or tap once to launch it.
Press twice then use the arrow keys to browse through the apps. Press to launch an app.
Customizing apps
You can move, resize, unpin, or close apps from the Start screen using the following steps:
Moving apps
Double-tap on the app then drag and drop the app to a new location.
Resizing apps
Right-click on the app to activate the Customize bar, then tap/click and select an app tile size.
50 Notebook PC E-Manual
Unpinning apps
Right-click on the app to activate the Customize bar then tap/click .
Closing apps
1. Move your mouse pointer on the top side of the launched app then wait for the pointer to change to a hand icon.
2. Drag then drop the app to the bottom of the screen to close it.
From the running app’s screen, press .
Notebook PC E-Manual 51
Accessing the Apps screen
Aside from the apps already pinned on your Start screen, you can also open other applications through the Apps screen.
NOTE: Actual apps shown onscreen may vary per model. The following screenshot is for reference only.
Launching the Apps screen
Launch the Apps screen using your Notebook PC's touchpad or keyboard.
On the Start screen, click the button.
From the Start screen, Press then press .
52 Notebook PC E-Manual
Pinning more apps on the Start screen
You can pin more apps on the Start screen using your touchpad.
1. Launch the All Apps screen
2. Right-click on the apps that you want to add on the Start screen.
3. Tap/click on the icon to pin the selected apps on the Start screen.
Notebook PC E-Manual 53
Charms bar
The Charms bar is a toolbar that can be triggered on the right side of your screen. It consists of several tools that allow you to share applications and provide quick access for customizing the settings of your Notebook PC.
Charms bar
54 Notebook PC E-Manual
Launching the Charms bar
NOTE: When called out, the Charms bar initially appears as a set of white icons. The image above shows how the Charms bar looks like once activated.
Use your Notebook PC’s touchpad or keyboard to launch the Charms bar.
Move your mouse pointer on the upper or lower right corner of the screen.
Press
Notebook PC E-Manual 55
Inside the Charms bar
Search
This charm allows you to look for files, applications, or programs in your Notebook PC.
Share
This charm allows you to share applications via social networking sites or email.
Start
This charm reverts the display back to the Start screen.
From the Start screen, you can also use this to revert back to a recently opened app.
Devices
This charm allows you to access and share files with the devices attached to your Notebook PC such as an external display or printer.
Settings
This charm allows you to access the PC settings of your
Notebook PC.
56 Notebook PC E-Manual
Snap feature
The Snap feature displays two apps side-by-side, allowing you to work or switch between apps.
IMPORTANT! Ensure that your Notebook PC’s screen resolution is set to
1366 x 768 pixels or higher before using the Snap feature.
Snap bar
Notebook PC E-Manual 57
Using Snap
Use your Notebook PC’s touchpad or keyboard to activate and use Snap.
1. Launch the app you wish to snap.
2. Hover the mouse point on the top side of your screen.
3. Once the pointer changes to a hand icon, drag then drop the app to the left or right side of the display panel.
4. Launch another app.
1. Launch the app you wish to snap.
2. Press and the left or right arrow key to snap the app to the left or right pane.
3. Launch another app. This app is automatically placed in the empty pane.
58 Notebook PC E-Manual
Other keyboard shortcuts
Using the keyboard, you can also use the following shortcuts to help you launch applications and navigate Windows® 8.1.
\
Switches between the Start screen and the last running app
Launches the desktop
Launches the This PC window on Desktop mode
Opens the File option from the Search charm
Opens the Share charm
Opens the Settings charm
Opens the Devices charm
Activates the Lock screen
Minimizes all currently active windows
Notebook PC E-Manual 59
60
Launches the Project pane
Opens the Everywhere option from the
Search charm
Opens the Run window
Opens Ease of Access Center
Opens the Settings option under the Search charm
Opens the context menu of the Start button
Launches the magnifier icon and zooms in your screen
Zooms out your screen
Opens the Narrator Settings
Notebook PC E-Manual
Connecting to wireless networks
Wi-Fi
Access emails, surf the Internet, and share applications via social networking sites using your Notebook PC’s Wi-Fi connection.
IMPORTANT! The Airplane mode disables this feature. Ensure that
Airplane mode is turned off before enabling the Wi-Fi connection of your
Notebook PC.
Enabling Wi-Fi
Activate Wi-Fi in your Notebook PC using the following steps on your touchpad.
1. Launch the Charms bar.
2. Tap/click and tap/click .
3. Select an access point from the list of available Wi-Fi connections.
NOTE: You may be prompted to enter a security key to activate the Wi-Fi connection.
5. If you want to enable sharing between your
Notebook PC and other wireless-enabled systems, tap/click Yes. Tap/click No if you do not want to enable the sharing function.
Notebook PC E-Manual 61
Bluetooth
Use Bluetooth to facilitate wireless data transfers with other Bluetoothenabled devices.
IMPORTANT! The Airplane mode disables this feature. Ensure that
Airplane mode is turned off before enabling the Bluetooth connection of your Notebook PC.
Pairing with other Bluetooth-enabled devices
You need to pair your Notebook PC with other Bluetooth-enabled devices to enable data transfers. To do this, use your touchpad as follows:
1. Launch the Charms bar.
2. Tap/click then tap/click Change PC Settings.
PC Settings, select Devices then tap/click Add
a Device to search for Bluetooth-enabled devices.
4. Select a device from the list. Compare the passcode on your Notebook PC with the passcode sent to your chosen device. If they are the same, tap/click Yes to successfully pair your Notebook PC with the device.
NOTE: For some bluetooth-enabled devices, you may be prompted to key in the passcode of your Notebook PC.
62 Notebook PC E-Manual
Airplane mode
The Airplane mode disables wireless communication, allowing you to use your Notebook PC safely while in-flight.
Turning Airplane mode on
1. Launch the Charms bar.
2. Tap/click and tap/click .
3. Move the slider to the right to turn the Airplane mode on.
Press .
Turning Airplane mode off
1. Launch the Charms bar.
2. Tap/click and tap/click .
3. Move the slider to the left to turn the Airplane mode off.
Press .
NOTE: Contact your airline provider to learn about related inflight services that can be used and restrictions that must be followed when using your
Notebook PC in-flight.
Notebook PC E-Manual 63
Connecting to wired networks
You can also connect to wired networks, such as local area networks and broadband Internet connection, using your Notebook PC’s LAN port.
NOTE: Contact your Internet Service Provider (ISP) for details or your network administrator for assistance in setting up your Internet connection.
To configure your settings, refer to the following procedures.
IMPORTANT! Ensure that a network cable is connected between your
Notebook PC’s LAN port and a local area network before performing the following actions.
Configuring a dynamic IP/PPPoE network connection
1. Launch Desktop.
2. From the Windows ® taskbar, right-click the network icon then tap/click Open Network and
Sharing Center.
3. In the Network and Sharing Center window, tap/ click Change adapter settings.
4. Right-click on your LAN then select Properties.
Internet Protocol Version 4(TCP/IPv4) then tap/click Properties.
64 Notebook PC E-Manual
Obtain an IP address automatically then tap/click OK.
NOTE: Proceed to the next steps if you are using PPPoE connection.
7. Return to the Network and Sharing Center window then tap/click Set up a new connection or
network.
10. Type your User name, Password, and Connection name then tap/click Connect.
12. Tap/click on the taskbar then tap/click the connection you just created.
13. Type your user name and password then tap/click
Connect to start connecting to the Internet.
Configuring a static IP network connection
1. Repeat steps 1 to 5 under Configuring a dynamic
IP/PPPoE network connection.
3. Type the IP address, Subnet mask and Default gateway from your service provider.
4. If needed, you can also type the preferred DNS server address and alternate DNS server address then tap/click OK.
Notebook PC E-Manual 65
Turning your Notebook PC off
You can turn off your Notebook PC by doing either of the following procedures:
•
•
•
•
Tap/click from the Charms bar then tap/click shutdown.
> Shut down to do a normal
From the log-in screen, tap/click
down.
> Shut
You can also shut down your Notebook PC using
Desktop mode. To do this, launch the desktop then press alt + f4 to launch the Shut Down window. Select Shut Down from the drop-down list then select OK.
If your Notebook PC is unresponsive, press and hold the power button for at least four (4) seconds until your Notebook PC turns off.
Putting your Notebook PC to sleep
To put your Notebook PC on Sleep mode, press the power button once.
You can also put your Notebook PC to sleep mode using Desktop mode. To do this, launch the desktop then press alt + f4 to launch the Shut Down window.
Select Sleep from the drop-down list then select OK.
66 Notebook PC E-Manual
Windows
®
8.1 lock screen
The Windows® 8.1 lock screen appears when you wake your Notebook
PC from sleep or hibernate mode. It also appears when you lock or unlock Windows® 8.1.
The lock screen can be customized to regulate access to your operating system. You can change its background display and access some of your apps while your Notebook PC is still locked.
To proceed from the lock screen
1. Tap/click on the touchpad or press any key on your Notebook PC's keyboard.
2. (optional) If your account is password-protected, you need to key in the password to continue to the Start screen.
Notebook PC E-Manual 67
Customizing your lock screen
You can customize your lock screen to show your preferred photo, a photo slideshow, app updates, and quickly access your Notebook PC’s camera. To change the settings of your lock screen, you may refer to the following information:
Selecting a photo
1. Launch the Charms bar > Settings.
3. Under the Lock screen preview, click Browse to select the photo you would like to use as a background on your lock screen.
Playing a slideshow
1. Launch the Charms bar > Settings.
3. Under the Lock screen preview, move the Play
a slide show on the lock screen slide bar to On.
4. Scroll down to customize the following options for your lock screen’s slideshow:
68 Notebook PC E-Manual
Adding app updates
1. Launch the Charms bar > Settings.
3. Scroll down until you see the Lock screen apps option.
4. Use the following options to add the apps whose updates you would like to see from your lock screen:
Activating your Notebook PC camera from the lock screen
From the lock screen, you can swipe down to activate and use your
Notebook PC's camera. Refer to the following steps on how to enable this feature:
1. Launch the Charms bar > Settings.
3. Scroll down until you see the Camera option.
4. Move the slide bar to On.
Notebook PC E-Manual 69
70 Notebook PC E-Manual
Chapter 4:
Power-On Self-Test (POST)
Notebook PC E-Manual 71
•
•
The Power-On Self-Test (POST)
The Power-On Self-Test (POST) is a series of software-controlled diagnostic tests that run when you turn on or restart your Notebook PC.
The software that controls the POST is installed as a permanent part of the Notebook PC’s architecture.
Using POST to access BIOS and Troubleshoot
During POST, you can access the BIOS settings or run troubleshooting options using the function keys of your Notebook PC. You may refer to the following information for more details.
BIOS
The Basic Input and Output System (BIOS) stores system hardware settings that are needed for system startup in the Notebook PC.
The default BIOS settings apply to most conditions of your Notebook
PC. Do not change the default BIOS settings except in the following circumstances:
An error message appears onscreen during system bootup and requests you to run the BIOS Setup.
You have installed a new system component that requires further
BIOS settings or updates.
WARNING: Using inappropriate BIOS settings may result to system instability or boot failure. We strongly recommend that you change the
BIOS settings only with the help of a trained service personnel.
Accessing BIOS
Restart your Notebook PC then press during POST.
72 Notebook PC E-Manual
BIOS Settings
NOTE: The BIOS screens in this section are for reference only. The actual screens may differ by model and territory.
Boot
This menu allows you to set your boot option priorities. You may refer to the following procedures when setting your boot priority.
1. On the Boot screen, select Boot Option #1.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Boot Security Save & Exit
Boot Configuration
Sets the system boot order
Fast Boot [Enabled]
Launch CSM [Disabled]
Driver Option Priorities
Boot Option Priorities
Boot Option #1 [Windows Boot Manager]
Add New Boot Option
Delete Boot Option
→→ : Select Screen
→→ : Select Item
Enter: Select
+/— : Change Opt.
F1 : General Help
F9 : Optimized Defaults
F10 : Save & Exit
ESC : Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc.
Notebook PC E-Manual 73
2. Press and select a device as the Boot Option #1.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Boot Security Save & Exit
Boot Configuration
Fast Boot [Enabled]
Sets the system boot order
Launch CSM [Disabled]
Driver Option Priorities
Boot Option Priorities
Add New Boot Option
Delete Boot Option
Boot Option #1
Boot Option #1 [Windows Boot Manager]
Disabled
→→ : Select Screen
→→ : Select Item
Enter: Select
+/— : Change Opt.
F1 : General Help
F9 : Optimized Defaults
F10 : Save & Exit
ESC : Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc.
74 Notebook PC E-Manual
Security
This menu allows you to set up the administrator and user password of your Notebook PC. It also allows you to control the access to your
Notebook PC’s hard disk drive, input/output (I/O) interface, and USB interface.
NOTE:
• If you install a User Password, you will be prompted to input this before entering your Notebook PC's operating system.
• If you install an Administrator Password, you will be prompted to input this before entering BIOS.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Boot Security Save & Exit
Password Description
If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the user’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup, the User will have
Administrator rights.
Administrator Password Status NOT INSTALLED
User Password Status NOT INSTALLED
Set Administrator
Password. The password length must be in the following range:
Minimum length 3
Maximum length 20
Administrator Password
User Password
HDD Password Status : NOT INSTALLED
Set Master Password
Set User Password
I/O Interface Security
System Mode state User
Secure Boot state Enabled
Secure Boot Control [Enabled]
Key Management
→→
→→
: Select Screen
: Select Item
Enter: Select
+/— : Change Opt.
F1 : General Help
F9 : Optimized Defaults
F10 : Save & Exit
ESC : Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc.
Notebook PC E-Manual 75
To set the password:
1. On the Security screen, select Administrator Password or User
Password.
2. Type in a password then press .
3. Re-type to confirm the password then press .
To clear the password:
1. On the Security screen, select Administrator Password or User
Password.
2. Type in the current password then press .
3. Leave the Create New Password field blank then press
.
.
76 Notebook PC E-Manual
I/O Interface Security
In the Security menu, you can access I/O Interface Security to lock or unlock some interface functions of your Notebook PC.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Security
I/O Interface Security If Locked, LAN controller will be disabled.
LAN Network Interface [UnLock]
Wireless Network Interface [UnLock]
HD AUDIO Interface [UnLock]
USB Interface Security
Lock
UnLock
LAN Network Interface
→→ : Select Screen
→→ : Select Item
Enter: Select
+/— : Change Opt.
F1 : General Help
F9 : Optimized
Defaults
F10 : Save & Exit
ESC : Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc.
To lock an interface:
1. On the Security screen, select I/O Interface Security.
2. Select an interface you would like to lock then press
.
Notebook PC E-Manual 77
78
USB Interface Security
Through the I/O Interface Security menu, you can also access USB
Interface Security to lock or unlock ports and devices.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Security
USB Interface Security
If Locked, all
USB device will be disabled
USB Interface [UnLock]
External Ports [UnLock]
CMOS Camera [UnLock]
Card Reader [UnLock]
USB Interface
Lock
UnLock
→→ : Select Screen
→→ : Select Item
Enter: Select
+/— : Change Opt.
F1 : General Help
F9 : Optimized
Defaults
F10 : Save & Exit
ESC : Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc.
To lock the USB interface:
1. On the Security screen, select I/O Interface Security > USB
Interface Security.
2. Select an interface that you would like to lock then select
Lock.
NOTE: Setting the USB Interface to Lock also locks and hides the
External Ports and other devices included under USB Interface Security.
Notebook PC E-Manual
Set Master Password
In the Security menu, you can use Set Master Password to set up a password-enabled access to your hard disk drive.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Boot Security Save & Exit
Password Description
If ONLY the Administrator’s password is set,then this only limits access to Setup and is only asked for when entering Setup.
If ONLY the user’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup, the User will have Administrator rights.
Set HDD Master
Password.
***Advisable to
Power Cycle System after Setting Hard
Disk Passwords***
Administrator Password Status NOT INSTALLED
User Password Status NOT INSTALLED
Administrator Password
User Password
HDD Password Status : NOT INSTALLED
Set Master Password
Set User Password
I/O Interface Security
→→ : Select Screen
→→ : Select Item
Enter: Select
+/— : Change Opt.
F1 : General Help
F9 : Optimized
Defaults
F10 : Save & Exit
ESC : Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc.
To set the HDD password:
1. On the Security screen, select Set Master Password.
2. Type in a password then press .
3. Re-type to confirm the password then press .
Set User Password then repeat the previous steps to set up the user password.
Notebook PC E-Manual 79
Save & Exit
To keep your configuration settings, select Save Changes and Exit before exiting the BIOS.
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Boot Security Save & Exit
Save Changes and Exit
Discard Changes and Exit
Exit system setup after saving the changes.
Save Options
Save Changes
Discard Changes
Restore Defaults
Boot Override
Windows Boot Manager
Launch EFI Shell from filesystem device
→→ : Select Screen
→→ : Select Item
Enter: Select
+/— : Change Opt.
F1 : General Help
F9 : Optimized Defaults
F10 : Save & Exit
ESC : Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc.
80 Notebook PC E-Manual
To update the BIOS:
1. Verify the Notebook PC’s exact model then download the latest
BIOS file for your model from the ASUS website.
2. Save a copy of the downloaded BIOS file to a flash disk drive.
3. Connect your flash disk drive to your Notebook PC.
4. Restart your Notebook PC then press during POST.
5. From the BIOS menu, Select Advanced > Start Easy Flash, then press .
Aptio Setup Utility - Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Boot Security Save & Exit
Start Easy Flash
Internal Pointing Device [Enabled]
Wake on Lid Open [Enabled]
Power Off Energy Saving [Enabled]
SATA Configuration
Graphics Configuration
Intel (R) Anti-Theft Technology Corporation
USB Configuration
Network Stack
Press Enter to run the utility to select and update
BIOS.
→→ : Select Screen
→→ : Select Item
Enter: Select
+/— : Change Opt.
F1 : General Help
F9 : Optimized Defaults
F10 : Save & Exit
ESC : Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc.
Notebook PC E-Manual 81
6. Locate your downloaded BIOS file in the flash disk drive then press .
Current BIOS
Platform: Q502
Version: 101
Build Date: Oct 26 2012
Build Time: 11:51:05
FSO
FS1
FS2
FS3
FS4
ASUSTek Easy Flash Utility
FLASH TYPE: MXIC 25L Series
New BIOS
Platform: Unknown
Version: Unknown
Build Date: Unknown
Build Time: Unknown
0 EFI
<DIR>
[→→]: Switch [→→]: Choose [q]: Exit [Enter]: Enter/Execute
7. After the BIOS update process, select Exit > Restore Defaults to restore the system to its default settings.
82 Notebook PC E-Manual
Troubleshoot
By pressing during POST, you can access Windows® 8.1 troubleshoot options which includes the following:
•
•
•
Refresh your PC
Reset your PC
Advanced options
Refresh your PC
Use Refresh your PC if you want to refresh your system without losing your current files and applications.
To access this during POST:
1. Restart your Notebook PC then press during
POST.
2. Wait for Windows® to load the Choose an option screen then tap/click Troubleshoot.
4. In the Refresh your PC screen, read the bullet points to learn more about using this option then tap/click
Next.
5. Tap/click the account you would like to refresh.
6. Type your account password then tap/click
Continue.
Notebook PC E-Manual
IMPORTANT! Ensure that your Notebook PC is plugged in to a power source before refreshing your system.
83
Reset your PC
IMPORTANT! Back up all your data before performing this option.
Use Reset your PC to restore your Notebook PC to its default settings.
To access this during POST:
1. Restart your Notebook PC then press
POST.
during
2. Wait for Windows® to load the Choose an option screen then tap/click Troubleshoot.
4. In the Reset your PC screen, read the bullet points to learn more about using this option then tap/click
Next.
5. Tap/click your preferred reset option: Just remove
my files or Fully clean the drive.
6. Tap/click Reset.
IMPORTANT! Ensure that your Notebook PC is plugged in to a power source before resetting your system.
84 Notebook PC E-Manual
Advanced options
Use Advanced options to perform additional troubleshooting options in your Notebook PC.
To access this during POST:
1. Restart your Notebook PC then press during
POST.
2. Wait for Windows® to load the Choose an option screen then tap/click Troubleshoot.
4. In the Advanced options screen, select the troubleshooting option you wish to perform.
5. Follow the succeeding steps to complete the process.
Using System Image Recovery
Under Advanced options, you can use System Image Recovery to recover your system using your Notebook PC’s original image file.
To access this during POST:
1. Restart your Notebook PC then press
POST.
during
2. Wait for Windows® to load the Choose an option screen then tap/click Troubleshoot.
Notebook PC E-Manual 85
4. In the Advanced options screen, select System
Image Recovery.
5. Choose an account you would like to recover using a system image file.
6. Type your account password then tap/click
Continue.
Use the latest available system image
(recommended), then tap/click Next. You can also choose Select a system image if your system image is in an external device or DVD.
8. Follow the succeeding steps to complete the system image recovery procedure.
NOTE: We strongly recommend that you regularly backup your system to prevent data loss in case your Notebook
PC stops working.
86 Notebook PC E-Manual
Tips and FAQs
Notebook PC E-Manual 87
•
•
•
•
•
•
•
Useful tips for your Notebook PC
To help you maximize the use of your Notebook PC, maintain its system performance, and ensure all your data are kept secured, here are some useful tips that you can follow:
Update Windows® periodically to ensure that your applications have the latest security settings.
Use ASUS Live Update to update ASUS-exclusive applications, drivers and utilities in your Notebook PC. Refer to the ASUS Tutor installed in your Notebook PC for more details.
Use an anti-virus software to protect your data and keep this updated too.
Unless absolutely necessary, refrain from using force shutdown to turn off your Notebook PC.
Always backup your data and make it a point to create a backup data in an external storage drive.
Refrain from using the Notebook PC at extremely high temperatures. If you are not going to use your Notebook PC for a long period of time (at least a month), we recommend that you take out the battery if the battery is removable.
Disconnect all external devices and ensure you have the following items prior to resetting your Notebook PC:
- Product key for your operating systems and other installed applications
- Backup data
- Log in ID and password
- Internet connection information
88 Notebook PC E-Manual
Hardware FAQs
1. A black dot, or sometimes a colored dot, appears onscreen when I turn on the Notebook PC. What should I do?
Although these dots normally appear onscreen, they will not affect your system. If the incident continues and subsequently affects system performance, consult an authorized ASUS service center.
2. My display panel has an uneven color and brightness. How can I fix this?
The color and brightness of your display panel may be affected by the angle and current position of your Notebook PC. The brightness and color tone of your Notebook PC may also vary per model. You may use the function keys or the display settings in your operating system to adjust the appearance of your display panel.
3. How can I maximize my Notebook PC ‘s battery life?
You can try doing any of the following suggestions:
• Use the function keys to adjust the display brightness.
• Enable Battery Saving mode under Instant On.
• If you are not using any Wi-Fi connection, switch your system into Airplane mode.
• Disconnect unused USB devices.
• Close unused applications, especially those that take up too much system memory.
Notebook PC E-Manual 89
4. My battery LED indicator does not light up. What’s wrong?
• Check whether the power adapter or battery pack is attached correctly. You may also disconnect the power adapter or battery pack, wait for a minute, then reconnect them again to the power outlet and Notebook PC.
• If the problem still exists, contact your local ASUS service center for assistance.
5. Why is my touchpad not working?
• Press to enable your touchpad.
• Check if ASUS Smart Gesture has been set to disable the touchpad when connecting an external pointing device.
6. When I play audio and video files, why can’t I hear any sound from my Notebook PC’s audio speakers?
You can try doing any of the following suggestions:
• Press to turn up the speaker volume.
• Check if your speakers were set to mute.
• Check if a headphone jack is connected to your Notebook
PC and remove it.
• Unlock the I/O Interface Security in your system’s BIOS. For more details, refer to the I/O Interface Security section in this manual.
7. What should I do if my Notebook PC’s power adapter gets lost or my battery stops working?
Contact your local ASUS service center for assistance.
90 Notebook PC E-Manual
8. Why does audio still come out from my Notebook PC’s audio speakers even if I already connected my headphone into the right jack port?
Go to Control Panel > Hardware and Sound then access Audio
Manager to configure the settings.
9. My Notebook PC cannot do keystrokes correctly because my cursor keeps on moving. What should I do?
Make sure that nothing accidentally touches or presses on your touchpad while you type on the keyboard. You can also disable your touchpad by pressing .
10. My Notebook PC’s touchpad is not working. What should I do?
You can try doing any of the following suggestions:
• Check if ASUS Smart Gesture is set to disable touchpad by connecting an external pointing device to your Notebook
PC. If yes, disable this function.
• Press .
11. Instead of showing letters, pressing the “U”, “I”, and “O” keys on my keyboard displays numbers. How can I change this?
Press the key or (on selected models) on your Notebook PC to turn off this feature and use the said keys for inputting letters.
Notebook PC E-Manual 91
Software FAQs
1. When I turn on my Notebook PC, the power indicator lights up but not my drive activity indicator. System bootup does not happen as well. What can I do to fix this?
You can try doing any of the following suggestions:
• Force shutdown your Notebook PC by pressing the power button for more than four (4) seconds. Check if the power adapter and battery pack are inserted correctly then turn on your Notebook PC.
• If the problem still exists, contact your local ASUS service center for assistance.
2. What should I do when my screen displays this message:
“Remove disks or other media. Press any key to restart.”?
You can try doing any of the following suggestions:
• Remove all connected USB devices then restart your
Notebook PC.
• Remove any optical discs that are left inside the optical drive then restart.
• If the problem still exists, your Notebook PC might have a memory storage problem. Contact your local ASUS service center for assistance.
3. My Notebook PC boots slower than usual and my operating system lags. How can I fix this?
Delete the applications you recently installed or were not included with your operating system package then restart your system.
92 Notebook PC E-Manual
4. My Notebook PC does not boot up. How can I fix this?
You can try doing any of the following suggestions:
• Remove all connected devices to your Notebook PC then restart your system.
• Press F9 upon startup. When your Notebook PC enters
Troubleshooting, select Refresh or Reset your PC.
• If the problem still exists, contact your local ASUS service center for assistance.
5. Why can’t my Notebook PC wake up from sleep or hibernate mode?
• You need to press the power button to resume your last working state.
• Your system might have completely used up its battery power. Connect the power adapter to your Notebook PC and connect to a power outlet then press the power button.
Notebook PC E-Manual 93
6. How can I boot to DOS using my USB drive or ODD?
Refer to the following steps: a. Restart your Notebook PC and enter BIOS by pressing F2 on your keyboard.
b. Go to Boot > Launch CSM > Enabled. c. Go to the Security menu then set Secure Boot Control to
Disabled. d. Press F10 to save changes and exit BIOS. e. Press and hold ESC to launch boot menu when your
Notebook PC restarts.
94 Notebook PC E-Manual
Appendices
Notebook PC E-Manual 95
DVD-ROM Drive Information
(on selected models)
The DVD-ROM drive allows you to view and create your own CDs and DVDs. You can purchase an optional DVD viewer software to view DVD titles.
Regional Playback Information
Playback of DVD movie titles involves decoding MPEG2 video, digital AC3 audio and decryption of CSS protected content. CSS (sometimes called copy guard) is the name given to the content protection scheme adopted by the motion picture industry to satisfy a need to protect against unlawful content duplication.
Although the design rules imposed on CSS licensors are many, one rule that is most relevant is playback restrictions on regionalized content. In order to facilitate geographically staggered movie releases, DVD video titles are released for specific geographic regions as defined in “Region Definitions” below. Copyright laws require that all DVD movies be limited to a particular region (usually coded to the region at which it is sold). While DVD movie content may be released for multiple regions, CSS design rules require that any system capable of playing CSS encrypted content must only be capable of playing one region.
IMPORTANT! The region setting may be changed up to five times using the viewer software, then it can only play DVD movies for the last region setting. Changing the region code after that will require factory resetting which is not covered by warranty. If resetting is desired, shipping and resetting costs will be at the expense of the user.
96 Notebook PC E-Manual
Region Definitions
Region 1
Canada, US, US Territories
Region 2
Czech, Egypt, Finland, France, Germany, Gulf States, Hungary, Iceland, Iran,
Iraq, Ireland, Italy, Japan, Netherlands, Norway, Poland, Portugal, Saudi Arabia,
Scotland, South Africa, Spain, Sweden, Switzerland, Syria, Turkey, UK, Greece,
Former Yugoslav Republics, Slovakia
Region 3
Burma, Indonesia, South Korea, Malaysia, Philippines, Singapore, Taiwan, Thailand,
Vietnam
Region 4
Australia, Caribbean (Except US Territories), Central America, New Zealand, Pacific
Islands, South America
Region 5
CIS, India, Pakistan, Rest of Africa, Russia, North Korea
Region 6
China
Notebook PC E-Manual 97
Blu-ray ROM Drive Information
(on selected models)
The Blu-ray ROM Drive allows you to view high definition (HD) videos and other disc file formats such as DVDs and CDs.
Region Definitions
Region A
North, Central and South American countries, and their territories; Taiwan, Hong
Kong, Macao, Japan, Korea (South and North), South East Asian countries and their territories.
Region B
European, African, and South West Asian countries and their territories; Australia and New Zealand.
Region C
Central, South Asian, Eastern European countries and their territories; China and
Mongolia.
NOTE: Refer to Blu-ray Disc website at www.blu-raydisc.com/en/Technical/FAQs/BlurayDiscforVideo.aspx for more details.
Internal Modem Compliancy
The Notebook PC with internal modem model complies with JATE (Japan), FCC
(US, Canada, Korea, Taiwan), and CTR21. The internal modem has been approved in accordance with Council Decision 98/482/EC for pan-European single terminal connection to the public switched telephone network (PSTN). However due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems you should contact your equipment supplier in the first instance.
98 Notebook PC E-Manual
Overview
On 4th August 1998 the European Council Decision regarding the CTR 21 has been published in the Official Journal of the EC. The CTR 21 applies to all non voice terminal equipment with DTMF-dialling which is intended to be connected to the analogue PSTN (Public Switched Telephone Network).
CTR 21 (Common Technical Regulation) for the attachment requirements for connection to the analogue public switched telephone networks of terminal equipment (excluding terminal equipment supporting the voice telephony justified case service) in which network addressing, if provided, is by means of dual tone multi-frequency signalling.
Network Compatibility Declaration
Statement to be made by the manufacturer to the Notified Body and the vendor:
“This declaration will indicate the networks with which the equipment is designed to work and any notified networks with which the equipment may have interworking difficulties.”
Statement to be made by the manufacturer to the user: “This declaration will indicate the networks with which the equipment is designed to work and any notified networks with which the equipment may have inter-working difficulties.
The manufacturer shall also associate a statement to make it clear where network compatibility is dependent on physical and software switch settings. It will also advise the user to contact the vendor if it is desired to use the equipment on another network.”
Up to now the Notified Body of CETECOM issued several pan-European approvals using CTR 21. The results are Europe’s first modems which do not require regulatory approvals in each individual European country.
Non-Voice Equipment
Answering machines and loud-speaking telephones can be eligible as well as modems, fax machines, auto-dialers and alarm systems. Equipment in which the end-to-end quality of speech is controlled by regulations (e.g. handset telephones and in some countries also cordless telephones) is excluded.
Notebook PC E-Manual 99
This table shows the countries currently under the CTR21 standard.
Country
Austria 1
Belgium
Czech Republic
Denmark 1
Finland
France
Germany
Greece
Hungary
Iceland
Ireland
Italy
Israel
Lichtenstein
Luxemburg
The Netherlands 1
Norway
Poland
Portugal
Spain
Sweden
Switzerland
United Kingdom
No
Yes
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Applied
Yes
Yes
No
Yes
No
Yes
Yes
Still Pending
No
Yes
Yes
Yes
No
No
No
More Testing
No
No
Not Applicable
No
Not Applicable
No
No
Still Pending
No
No
No
Yes
No
Not Applicable
Not Applicable
Not Applicable
No
No
No
100 Notebook PC E-Manual
This information was copied from CETECOM and is supplied without liability. For updates to this table, you may visit http://www.cetecom.de/technologies/ctr_21.
html
1 National requirements will apply only if the equipment may use pulse dialling
(manufacturers may state in the user guide that the equipment is only intended to support DTMF signalling, which would make any additional testing superfluous).
In The Netherlands additional testing is required for series connection and caller
ID facilities.
Federal Communications Commission
Interference Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
•
•
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to Part 15 of the Federal Communications Commission
(FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Notebook PC E-Manual 101
•
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of a shielded-type power cord is required in order to meet
FCC emission limits and to prevent interference to the nearby radio and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
(Reprinted from the Code of Federal Regulations #47, part 15.193, 1993.
Washington DC: Office of the Federal Register, National Archives and Records
Administration, U.S. Government Printing Office.)
FCC Radio Frequency (RF) Exposure Caution
Statement
WARNING! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
“The manufacture declares that this device is limited to Channels 1 through 11 in the
2.4GHz frequency by specified firmware controlled in the USA.”
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. End users must follow the specific operating instructions for satisfying RF exposure compliance.
102 Notebook PC E-Manual
•
•
•
•
•
•
•
Declaration of Conformity (R&TTE directive
1999/5/EC)
The following items were completed and are considered relevant and sufficient:
Essential requirements as in [Article 3]
Protection requirements for health and safety as in [Article 3.1a]
Testing for electric safety according to [EN 60950]
Protection requirements for electromagnetic compatibility in [Article 3.1b]
Testing for electromagnetic compatibility in [EN 301 489-1] & [EN 301
489-17]
Effective use of the radio spectrum as in [Article 3.2]
Radio test suites according to [EN 300 328-2]
CE Marking
CE marking for devices without wireless LAN/Bluetooth
The shipped version of this device complies with the requirements of the EEC directives 2004/108/EC “Electromagnetic compatibility” and 2006/95/EC “Low voltage directive”.
CE marking for devices with wireless LAN/ Bluetooth
This equipment complies with the requirements of Directive 1999/5/EC of the
European Parliament and Commission from 9 March, 1999 governing Radio and
Telecommunications Equipment and mutual recognition of conformity.
Notebook PC E-Manual 103
IC Radiation Exposure Statement for Canada
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with IC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting. End users must follow the specific operating instructions for satisfying RF exposure compliance.
Operation is subject to the following two conditions:
• This device may not cause interference and
• This device must accept any interference, including interference that may cause undesired operation of the device.
To prevent radio interference to the licensed service (i.e. co-channel Mobile
Satellite systems) this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
This device complies with Industry Canada licence-exempt RSS standard(s).
104 Notebook PC E-Manual
Déclaration d’Industrie Canada relative à l’ exposition aux ondes radio
Cet appareil est conforme aux limites d’exposition aux radiations d’Industrie
Canada définies pour un environnement non-contrôlé. Pour maintenir la conformité avec les exigences d’exposition RF d’IC, veuillez éviter tout contact direct avec l’antenne pendant l’émission. Les utilisateurs finaux doivent suivre les instructions de fonctionnement spécifiques pour satisfaire la conformité aux expositions RF.
Son utilisation est sujette aux deux conditions suivantes :
• Cet appareil ne peut pas causer d’interférence, et
• Cet appareil doit accepter toute interférence, y compris les interférences qui pourraient causer un fonctionnement non souhaité de l’appareil.
Pour éviter les interférences radio avec le service sous licence (c’est à-dire le partage de canal avec les systèmes de téléphonie satellite), cet appareil est destiné
à être utilisé en intérieur et loin des fenêtres pour fournir un blindage maximal.
Tout appareil (ou son antenne d’émission) qui est installé en extérieur est sujet à cette licence.
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Notebook PC E-Manual 105
Wireless Operation Channel for Different
Domains
N. America
Japan
Europe ETSI
2.412-2.462 GHz
2.412-2.484 GHz
2.412-2.472 GHz
Ch01 through CH11
Ch01 through Ch14
Ch01 through Ch13
•
•
France Restricted Wireless Frequency Bands
Some areas of France have a restricted frequency band. The worst case maximum authorized power indoors are:
10mW for the entire 2.4 GHz band (2400 MHz–2483.5 MHz)
100mW for frequencies between 2446.5 MHz and 2483.5 MHz
NOTE: Channels 10 through 13 inclusive operate in the band 2446.6 MHz to 2483.5
MHz.
•
•
There are few possibilities for outdoor use: on private property or on the private property of public persons, use is subject to a preliminary authorization procedure by the Ministry of Defense, with maximum authorized power of 100mW in the
2446.5–2483.5 MHz band. Use outdoors on public property is not permitted.
In the departments listed below, for the entire 2.4 GHz band:
Maximum authorized power indoors is 100mW
Maximum authorized power outdoors is 10mW
106 Notebook PC E-Manual
Departments in which the use of the 2400–2483.5 MHz band is permitted with an
EIRP of less than 100mW indoors and less than 10mW outdoors:
01 Ain
05 Hautes Alpes
02 Aisne
08 Ardennes
03 Allier
09 Ariège
11 Aude 12 Aveyron 16 Charente
24 Dordogne 25 Doubs 26 Drôme
32 Gers
41 Loir et Cher
55 Meuse
60 Oise
64 Pyrénées Atlantique
68 Haut Rhin
36 Indre
45 Loiret
58 Nièvre
61 Orne
66 Pyrénées Orientales
70 Haute Saône
37 Indre et Loire
50 Manche
59 Nord
63 Puy du Dôme
67 Bas Rhin
71 Saône et Loire
75 Paris 82 Tarn et Garonne 84 Vaucluse
88 Vosges 89 Yonne 90 Territoire de Belfort
94 Val de Marne
This requirement is likely to change over time, allowing you to use your wireless
LAN card in more areas within France. Please check with ART for the latest information (www.arcep.fr)
NOTE: Your WLAN Card transmits less than 100mW, but more than 10mW.
Notebook PC E-Manual 107
•
•
UL Safety Notices
Required for UL 1459 covering telecommunications (telephone) equipment intended to be electrically connected to a telecommunication network that has an operating voltage to ground that does not exceed 200V peak, 300V peak-to-peak, and 105V rms, and installed or used in accordance with the National Electrical
Code (NFPA 70).
When using the Notebook PC modem, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
• DO NOT use the Notebook PC near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
• DO NOT use the Notebook PC during an electrical storm. There may be a remote risk of electric shock from lightning.
• DO NOT use the Notebook PC in the vicinity of a gas leak.
Required for UL 1642 covering primary (nonrechargeable) and secondary
(rechargeable) lithium batteries for use as power sources in products. These batteries contain metallic lithium, or a lithium alloy, or a lithium ion, and may consist of a single electrochemical cell or two or more cells connected in series, parallel, or both, that convert chemical energy into electrical energy by an irreversible or reversible chemical reaction.
Do not dispose the Notebook PC battery pack in a fire, as they may explode. Check with local codes for possible special disposal instructions to reduce the risk of injury to persons due to fire or explosion.
Do not use power adapters or batteries from other devices to reduce the risk of injury to persons due to fire or explosion. Use only UL certified power adapters or batteries supplied by the manufacturer or authorized retailers.
108 Notebook PC E-Manual
Power Safety Requirement
Products with electrical current ratings up to 6A and weighing more than 3Kg must use approved power cords greater than or equal to: H05VV-F, 3G, 0.75mm
H05VV-F, 2G, 0.75mm
2 .
2 or
TV Notices
Note to CATV System Installer—Cable distribution system should be grounded
(earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial
Cable – installation should include bonding the screen of the coaxial cable to the earth at the building entrance.
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and
Restriction of Chemicals) regulatory framework, we publish the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/
REACH.htm.
Macrovision Corporation Product Notice
This product incorporates copyright protection technology that is protected by method claims of certain U.S.A. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Prevention of Hearing Loss
To prevent possible hearing damage, do not listen at high volume levels for long periods.
Notebook PC E-Manual 109
Nordic Lithium Cautions (for lithium-ion batteries)
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. (English)
ATTENZIONE! Rischio di esplosione della batteria se sostituita in modo errato.
Sostituire la batteria con un una di tipo uguale o equivalente consigliata dalla fabbrica. Non disperdere le batterie nell’ambiente. (Italian)
VORSICHT! Explosionsgefahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ.
Entsorgung gebrauchter Batterien nach Angaben des Herstellers. (German)
ADVARSELI! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. (Danish)
VARNING! Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. (Swedish)
VAROITUS! Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan sousittelemaan tyyppiin. Hävitä käytetty paristo valmistagan ohjeiden mukaisesti. (Finnish)
ATTENTION! Il y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du mêre type ou d’un type
équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. (French)
ADVARSEL! Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner. (Norwegian)
(Japanese)
ВНИМАНИЕ! При замене аккумулятора на аккумулятор иного типа возможно его возгорание. Утилизируйте аккумулятор в соответствии с инструкциями производителя. (Russian)
110 Notebook PC E-Manual
Optical Drive Safety Information
Laser Safety Information
CD-ROM Drive Safety Warning
CLASS 1 LASER PRODUCT
WARNING! To prevent exposure to the optical drive’s laser, do not attempt to disassemble or repair the optical drive by yourself. For your safety, contact a professional technician for assistance.
Service warning label
WARNING! INVISIBLE LASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM OR
VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug
Administration implemented regulations for laser products on August 2, 1976.
These regulations apply to laser products manufactured from August 1, 1976.
Compliance is mandatory for products marketed in the United States.
WARNING! Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product installation guide may result in hazardous radiation exposure.
Coating Notice
IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is applied to insulate the device except on the areas where the I/O ports are located.
Notebook PC E-Manual 111
English
Finnish
French
CTR 21 Approval (for Notebook PC with built-in
Modem)
Danish
Dutch
112 Notebook PC E-Manual
German
Greek
Italian
Portuguese
Spanish
Swedish
Notebook PC E-Manual 113
ENERGY STAR complied product
ENERGY STAR is a joint program of the U.S. Environmental
Protection Agency and the U.S. Department of Energy helping us all save money and protect the environment through energy efficient products and practices.
All ASUS products with the ENERGY STAR logo comply with the ENERGY STAR standard, and the power management feature is enabled by default. The monitor and computer are automatically set to sleep after 15 and 30 minutes of user inactivity. To wake your computer, click the mouse or press any key on the keyboard. Please visit http://www.energy.gov/powermanagement for detail information on power management and its benefits to the environment. In addition, please visit http://www.energystar.gov for detail information on the
ENERGY STAR joint program.
NOTE: Energy Star is NOT supported on FreeDOS and Linux-based operating systems.
European Union Eco-label
This Notebook PC has been awarded the EU Flower label, which means that this product has the following characteristics:
1. Decreased energy consumption during use and stand-by modes.
4.
5.
2.
3.
Limited use of toxic heavy metals.
Limited use of substances harmful to the environment and health.
Reduction of the use of natural resources by encouraging recycling.
Designed for easy upgrades and longer lifetime through providing compatible spare parts such as batteries, power supplies, the keyboard, the memory, and if available the CD drive or DVD drive.
6. Reduced solid waste through takeback policy.
For more information on the EU Flower label, please visit the European Union Ecolabel website at http://www.ecolabel.eu.
114 Notebook PC E-Manual
Global Environmental Regulation Compliance and Declaration
ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements.
Please refer to http://csr.asus.com/english/Compliance.htm for information disclosure based on regulation requirements ASUS is complied with:
Japan JIS-C-0950 Material Declarations
EU REACH SVHC
Korea RoHS
Swiss Energy Laws
ASUS Recycling/Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http://csr.asus.com/ english/Takeback.htm for detailed recycling information in different regions.
Rechargeable Battery Recycling Service in
North America
For customers in US and Canada:
If you have rechargeable batteries of ASUS products that needs to be recycled, you may call 1-800-822-8837 (toll-free) for assistance.
Notebook PC E-Manual 115
Regional notice for Singapore
This ASUS product complies with IDA Standards.
Complies with
IDA Standards
DB103778
Regional notice for India
This product complies with the “India E-waste (Management and
Handling) Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls (PBBs), and polybrominated diphenyl ethers (PBDEs) in concentrations exceeding 0.1% by weight in homogenous materials for cadmium, except for the exemptions listed in Schedule-II of the Rule.
116 Notebook PC E-Manual
Notebook PC E-Manual 117
118 Notebook PC E-Manual
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project