®
Vintage-PH1
Barebone System
Quick Start Guide
Front panel features
N O T E . The photos in this guide are for reference only. For detailed
information on your system’s specifications, refer to the user guide.
External
Internal
5.25-inch bays
(drive not
included)
HDD bay
FDD bay
(drive not
included)
Reset Button
HDD LED
Power button
USB 2.0 ports
IEEE port1394 ports
Microphone port
Headphone port
Rear panel features
Power socket
Voltage selector
Power supply
module
PS/2 keyboard port
PS/2 mouse port
Serial port
VGA port
USB 2.0 ports
USB 2.0 ports
Center/Subwoofer port
Side Speaker Out port
Rear Speaker Out port
Microphone port
Line Out port
Line In port
ii
Parallel port
Chassis fan vent
I E E E 1 3 9 4 port
L AN (RJ-45) port
Expansion slots
Voltage selector
The switching power supply that came
with the system has a voltage selector
switch below the power socket. Use this
switch to select the appropriate voltage
according to the voltage supply in your
area.
115V/230V
Voltage selector
If the voltage supply in your area is
100-127V, set the switch to 115V.
C A U T I O N . Setting the
switch to 115V in a 230V
environment will seriously
damage the system!
If the voltage supply in your area is
200-240V, set the switch to 230V.
Internal components
1
3
4
5
2
6
1.
PFC power supply
4.
3.5” HDD drive bay
2.
Motherboard
5.
3.5” Floppy drive bay
3.
Two 5.25” optical drive bays
6.
Hard disk drive bays
iii
Removing the side plate and front cover
1
2
Screw
Remove the two screws on the rear
panel.
3
Side lock tab
I M P O R T A N T . Repeat
steps 1 and 2 to remove
the other side plate.
4
Release the side lock tabs.
Hinge-like tab
Swing the left edge of the front
panel outward, then unhook the
hinge-like tabs from the holes on
the right side of the front panel.
iv
Installing a CPU
C A U T I O N . Incorrect installation of the CPU into the socket may bend
the pins and severely damage the CPU!
PnP Cap
Retention tab
A
Load lever
B
This side of the cam
box should face you.
1
Press the load lever with your thumb (A) and move it to the left (B) until it
is released from the retention tab.
3
2
B
Load plate
A
Alignment key
Gold triangle mark
Lift the load lever in the direction
of the arrow to a 135º angle.Lift
the load plate with your thumb
and forefinger to a 100º angle (A),
then push the PnP cap from the
load plate window to remove (B).
4
Position the CPU over the socket,
making sure that the gold triangle is
on the bottom-left corner of the
socket. The socket alignment key
should fit into the CPU notch.
A
B
Close the load plate (A), then push the
load lever (B) until it snaps into the
retention tab.
v
Installing system memory
C A U T I O N . A DDR
DIMM is keyed with
a notch so that it
fits in only one
direction. DO NOT
force a DIMM into a
socket to avoid
damaging the DIMM.
2
1
1
DIMM notch
Socket break
Installing the fan and heatsink assembly
N O T E . Your boxed Intel® Pentium® 4 processor package should come
with installation instructions for the CPU, heatsink, and the retention
mechanism. If the instructions in this section do not match the CPU
documentation, follow the latter.
1
2
B
A
A
B
Fastener
Motherboard hole
Place the heatsink on top of the
installed CPU, making sure that the
four fasteners match the holes on
the motherboard.
vi
Push down two fasteners at a time
in a diagonal sequence to secure
the heatsink and fan assembly in
place.
I M P O R T A N T . Do not
forget to connect the CPU
fan connector! Hardware
monitoring errors can occur
if you fail to plug this
connector.
Installing an optical drive
2
1
1
Remove the drive bay plate.
3
4
Installing a hard disk drive
Audio cable
IDE ribbon cable
Red stripe to pin 1
Power cable
HDD label
side
1
2
3
4
Primary IDE connector
Connect the blue interface of the IDE ribbon cable
to the primary IDE connector (blue connector
labeled PRI_IDE1) on the motherboard.
IDE ribbon cable
Power cable
vii
Replacing the side plate and front cover
2
1
Hinge-like tab
Side lock tab
Snap the side lock tabs to secure
the front panel.
4
3
Screw
Replace the side plate.
Drive in two screws on the rear
panel.
I M P O R T A N T . Repeat steps 3 and 4 to replace the other side plate.
viii