TOA C-BC711W Specification Sheet

COMBINATION

DOME CAMERA SYSTEMS

PAL

For Outdoor Use

Combination Dome Cameras

For Indoor Use

For Outdoor Use

C-CC774

C-CC764 multi-function type

C-CC714 standard type with Ceiling Mount

Cover C-BC511C

Brackets and Covers

For Indoor Use

C-CC574

C-CC564 multi-function type

C-CC514 standard type

C-BC711P

Ceiling Suspension

Bracket

C-BC711PM

Pole Mounting

Bracket

C-BC511C

Ceiling Mount

Cover

C-BC511P

Ceiling Suspension

Bracket

C-BC511U

Flush Ceiling

Mounting Bracket

C-BC511A

Ceiling Mounting

Bracket

C-BC711W

Wall Mounting

Bracket

C-A711DM

Smoked Dome

Cover

C-BC511C-S

Ceiling Mount

Cover (Smoked)

C-BC511W

Wall Mounting

Bracket

Remote Controllers

C-BC511U-S

Flush Ceiling Mounting

Bracket (Smoked)

C-RM500

Remote Controller for Camera and Multiplexer

C-RM1000

Remote Controller for Camera and Digital Video Recorder

Combination Dome Cameras

Configuring a perfect surveillance system.

■

Higher resolution delivers better images.

TOA cameras now feature a higher horizontal resolution of

540* 1 lines to deliver images of enhanced quality.

■

All points coverage at high speed.

TOA's new combination dome cameras help to improve monitoring environments with an ideal coverage area that is made possible with a 360 ° rotation range to cover any possible position. Capable of a maximum rotating speed

(panning/tilting) of 360 °/second, these versatile cameras allow rotation speed to be slowed down as desired.

■

Intelligent image optimizing using the Wide

Dynamic Range function.*

2

If the area of coverage exhibits varying brightness levels, it causes various problems that prevent achieving superb image quality. These problems pose severe difficulties for cameras that utilize conventional technology for dealing with brightness variations. The following two examples illustrate the problem.

Placing the focus on the outdoors results in the indoors being too dark to see well.

(Photo A)

However, setting the focus on the indoors now "whites out" the outdoor area.

(Photo B)

■

Expanded zooming ability.

TOA cameras are capably equipped for zooming as needed.

C-CC574 and C-CC774 incorporate a 35X ultra wide-angle zoom lens for better coverage of a desired image. If even more zooming is required, 12X digital zooming can be activated, resulting in an extraordinary combined zoom factor of up to 420X*.

* C-CC574 and C-CC774 cameras are equipped with a high-speed, wide-angle lens having a 35X zoom while C-CC564 and C-CC764 cameras are equipped with a high-speed, wide-angle lens having a

23X zoom (C-CC514 and C-CC714 having a 22X zoom). With the

12X digital zoom activated, a total 420X zoom is possible for

C-CC574, 276X zoom for C-CC564 and C-CC764 cameras and

264X zoom for C-CC514 and C-CC714 cameras.

■

Electronic Image Stabilizer.*

1

Using the camera at high zoom settings makes it very susceptible to wind. Even if the camera shakes slightly, images blur. TOA incorporates an image stabilization feature in the camera that minimizes movement-induced blurring to maintain stable images. In addition, the camera is also equipped with an angle-speed sensor that can maintain stable images even if monitoring low-light locations.

■

Sophisticated autofocus modes add versatility.

TOA cameras are equipped with advanced auto-focusing.

Three independent modes are offered: Auto focus for normal operation is activated with a single push. Stop Auto Focus activates if the camera view or viewing angle changes. To keep auto focus working continuously, the Continuous auto focus can be engaged.

TOA Combination Dome Cameras incorporate a special Digital Signal

Processor (DSP) that works to optimize image, producing a single image of exceptional clarity that is comparable to the same image when viewed with human eyes.

■

Motion detection function initiates operation.*

2

When a moving object enters a camera's field of view, the camera will initiate a preprogrammed operation or a series of operations. The camera's view can be monitored onscreen with a window that is divided into

64 segments and from these,

8 areas can be selected as motion detection zones.

■

Color image clarity maintained with sensitivity boost.

In night or dark lighting conditions, the camera's shutter speed is automatically reduced so that more light can enter.

This function effectively increases the camera's sensitivity so that dark areas can be made up to 32 times brighter.

FEATURES

■

Day/Night operation improves low light performance.*

2

Combination dome cameras also incorporate a separate B/W mode. At night, as light intensity decreases, this mode automatically activates, boosting camera sensitivity and making it possible to capture clear images even in unsatisfactory light conditions. When light conditions are satisfactory, the camera will revert to its primary function as a color camera. Used together, the sensitivity boost and B/W modes allow TOA combination dome cameras to efficiently function for 24-hour monitoring.

Note: B/W mode allows monitoring target areas that are not possible in normal light conditions.

Sensitivity boost allows cameras to provide good color image quality for dark areas.

B/W mode.

(color image)

(B/W image)

■

Protecting privacy.

a) Privacy Masking function.* 2

Depending on system use requirements, there may be several areas that the system administrator decides does not require surveillance for whatever reason. Users are allowed to select in advance the locations they wish to be excluded from surveillance in a camera's field of view.

Onscreen selected areas can be masked with a rectangle and a maximum of 8 areas can be masked for privacy.

*C-CC564/C-CC764: 2 masked area/screen

*C-CC574/C-CC774: 4 masked area/screen b) Restricting camera movement.

In addition to masking areas for privacy, a hardware-oriented method is also available. A camera's rotation range in both horizontal and vertical directions can be restricted to exclude areas from surveillance.

■

Outdoor installation ready.

(meets IP66 standards)

C-CC714, C-CC764 and C-CC774 utilize a waterproof and dustproof design that fully conforms to IP66 standards and can be safely installed outdoors. Cameras are cased in a special housing that withstands outdoor conditions, allowing them to be installed outdoors, even if the location is directly exposed to rain.

■

Withstands cold weather conditions.

C-CC714, C-CC764 and C-CC774 incorporate a heating circuit that allows operation in severe temperatures down to

–40 °C. Heating is automatically turned on when ambient temperatures go below 0 °C and will automatically switch off when the temperatures rise.

Note: Turning the camera on if the camera interior is below 0 °C may not result in producing an immediately viewable image. Once the camera interior temperature rises above 0 °C, images will be viewable.

■

Route tracing facilitates subject monitoring.

In order to make it easy to follow a subject along a route, the camera can be set to automatically monitor preset points for up to 60 seconds. Two different routes can be programmed.

■

Configuring programmable tours.

Through combinations of the 255 preset positions and trace function, a camera can be programmed to automatically and continuously repeat a travel pattern as a tour. Up to 16 tour patterns can be programmed. Any tour program is able to have a different travel pattern that can be activated by an alarm input or timer.

■

Programmable camera operation initiated by alarm input.

A useful Alarm function allows programming camera operation that can be activated by an alarm input. Desired camera operations such as position replay, touring, tracing, and control of the auxiliary terminal can be programmed to activate when the camera receives an alarm input. Each camera is equipped with three (C-CC564 and C-CC574 have eight) alarm inputs and each alarm input can be set to respond with different preprogrammed operation.

■

Preset operation start with Timer program function.

A camera can conveniently be set to begin operation at a preset time with a built-in timer. Each camera has a clock function that can be set to initiate operation at a preset time.

The timer can be set for a specific date, day of the week, or daily. Up to 16 different timer programs can be set.

* 1 C-CC574/C-CC774 only.

* 2 C-CC564/C-CC574/C-CC764/C-CC774 only.

Combination Dome Cameras

FEATURES

■

Titling options.

To facilitate camera use, various titles can be input and displayed on the monitor. In addition to camera and position titles, other titles for display include trace title, displayed while the trace function is on, tour title, displayed when tour function is activated, and alarm title displayed when an alarm input is received.

■

Flexible installation options.

TOA cameras can easily be installed on ceilings, walls or on poles thanks to the wide range of mounting brackets available.

■

Software for maintenance.

TOA cameras include dedicated software that allows easy titles to be set and to create a backup of parameters with a PC.

• Confirmation of camera operation

• Menu-based settings and backup of settings data

• Create title data settings in advance

• Upload camera firmware

■

Freeze preset function*

2

Displays the still image during camera movement between preset positions.

■

Multi-language

• Menu: 4 languages

• Camera ID: 8 languages

■

Auto positional deviation correction

When the camera has rotated to some degree of deviation.

■

Auto Refresh Function

Cleans horizontal rotation contacts periodically.

■

Other functions.

• Tilt (vertical) range: +5 ° to –185°.* 2

• Auto flip function* 2

• Rotation speed can be varied to match lens zooming ratio in manual operation mode.

• Flicker-free operation

• Alarm inputs and auxiliary contact output.

• RS-485 protocol control.

*

2

C-CC564/C-CC574/C-CC764/C-CC774 only.

Combination Dome Camera Comparison Table

Function/Specification

Application

Water Dust Protection

Operating Temperature

Auto Iris Lens Zoom Ratio

Focal Length (f =)

Electronic Zoom Ratio

Image Device

Horizontal Resolution (at Center)

Minimum Required Illumination

350mV

140mV

High Sensitivity ON 350mV

High Sensitivity ON 140mV

Number of Preset Positions

Zoom Speed (WIDE end to TELE end)

Preset Operaition

Manual Operation

Rotating Range Panning

Tilting

Rotating Speed

Electronic Image Stabilizer

Wide Dynamic Range

Back Light Compensation

White Balance

Sensitivity Up (Color mode)

Day/Night operation (B/W mode)

Motion Detection

Privacy Masking

Alarm Input

Contact Output

Power Source

C-CC774

Outdoor

IP66

–40

°C to +50°C

35X

3.4 – 119.0 mm

12X

1/4 CCD

540 line

1 lx

0.3 lx

0.005 lx

0.0015 lx

255+Home

2.0 sec.

3.2 sec.

360

° endless

+5 ° to –185°

360

°/sec.

●

●

●

ATW/AWB

Max. 32 times

●

●

● Max 8 area

Up to 4/Screen

3

1

24V AC

C-CC764

Outdoor

IP66

–40

°C to +50°C

23X

3.6 – 82.8 mm

12X

1/4 CCD

480 line

3 lx

1 lx

0.03 lx

0.01 lx

255+Home

1.5 sec.

2.9 sec.

360

° endless

+5 ° to –185°

360

°/sec.

—

●

●

ATW/AWB

Max. 32 times

●

●

● Max 8 area

Up to 2/Screen

3

1

24V AC

C-CC714

Outdoor

IP66

–40

°C to +50°C

22X

4.0 – 88.0 mm

12X

1/4 CCD

480 line

1 lx

0.3 lx

0.03 lx

0.01 lx

255+Home

1.3 sec.

2.4 sec.

360

° endless

+5 ° to –90°

360

°/sec.

—

—

●

ATW/AWB

Max. 32 times

—

—

—

—

3

1

24V AC

C-CC564

Indoor

—

–10

°C to +50°C

23X

3.6 – 82.8 mm

12X

1/4 CCD

480 line

3 lx

1 lx

0.03 lx

0.01 lx

255+Home

1.5 sec.

2.9 sec.

360

° endless

+5 ° to –185°

360

°/sec.

—

●

●

ATW/AWB

Max. 32 times

●

●

● Max 8 area

Up to 2/Screen

8

2

24V AC

C-CC574

Indoor

—

–10

°C to +50°C

35X

3.4 – 119.0 mm

12X

1/4 CCD

540 line

1 lx

0.3 lx

0.005 lx

0.0015 lx

255+Home

2.0 sec.

3.2 sec.

360

° endless

+5 ° to –185°

360

°/sec.

●

●

●

ATW/AWB

Max. 32 times

●

●

● Max 8 area

Up to 4/Screen

8

2

24V AC

C-CC514

Indoor

—

–10

°C to +50°C

22X

4.0 – 88.0 mm

12X

1/4 CCD

480 line

1 lx

0.3 lx

0.03 lx

0.01 lx

255+Home

1.3 sec.

2.4 sec.

360

° endless

+5 ° to –90°

360

°/sec.

—

—

●

ATW/AWB

Max. 32 times

—

—

—

—

3

1

24V AC

SETTING GUIDE

SETTING GUIDE

The camera menu screens are comprised of the following setting item screens.

CAMERA MENU

PRESET

ID SETTING

CAMERA SETTING

AUTO MODE

ALARM

AUX

TIMER

MANUAL

MAINTENANCE

LANGUAGE

Setting Item

PRESET SETTING

MEMORY* 1

READJUST ALL POS

MEMORY RESET

MEMORY ALL RESET

AUTO RETURN

HOME

FREEZE PRESET *

3

ID SETTINGS

DISPLAY

ID SETTING

LOCATION * 2

FRAME ADJUST

ZERO POINT

CAMERA SETTING

WHITE BALANCE* 2

BACKLIGHT *

2

BRIGHTNESS*

2

DAY/NIGHT *

2

*

3

AUTO FOCUS

AGC * 2

SLOW SHUTTER * 2

SHUTTER SPEED *

2

E- ZOOM

ENHANCER *

2

CHROMA *

2

SYNC

EIS *

5

SENSITIVITY *

5

RESET (CAM SETTING)

AUTO MODE

AUTO KEY

AUTO PAN

SEQUENCE

TRACE

TRACE 1 PAUSE TIME

TRACE 2 PAUSE TIME

TOUR

Sets the stop duration of trace movements.

Sets the operation to be programmed.

ALARM Sets alarm operations.

Programs the camera position (camera orientation), displays setting status, and performs reset.

Programs the camera position.

Corrects all preset camera positions.

Resets preset camera position.

Resets all preset camera positions.

The camera returns to the preset position automatically when the preset period of time elapses by external control.

Designates the program the camera automatically returns to.

Displays the still image during camera movement between preset positions.

AUX

INPUT

REPORT

ACTIVE STATE

PRIORITY

ACTION

INTERVAL

RESET ACTION

ALARM DATA

Sets input number of alarm input.

Sets the terminal that transmits the alarm information.

Selects whether to activate the alarm input with make or break contacts.

Sets whether to forcibly execute action or to set priority order to operation.

Sets camera operation when alarm signal is received.

Sets the period of time that alarm conditions are maintained.

Sets camera operation when the alarm conditions are released.

Verify alarm logs.

Sets contact output.

AUX1

AUX2 * 4



Sets the title.

Sets to display or hides the title.

Sets ID.

Sets title display position and its length.

Sets the character display position.

Sets the origin point of the angle display.

Sets camera properties.

TIMER

PROGRAM

TIME DISPLAY

DATE DISPLAY

ENTER TIMER

ENTER DATE

SUMMER TIME

Sets the timer.

Sets predetermined operations to be performed at preset times.

Sets time display to 12-hour or 24-hour display formats.

Sets date display.

Sets the time.

Sets the date.

Sets the summer time (Daylight saving time).

Sets the camera's white balance.

Sets the backlight compensation.

Adjusts the camera's brightness.

Sets to give operation priority to black & white mode or slow shutter mode depending on the subject’s brightness.

Sets Auto Focus mode.

Sets AGC.

Sets slow shutter.

Sets shutter speed.

Sets a maximum enlargement of electronic zoom.

Sets contour enhancement.

Adjusts the chroma.

Switches sync. system and adjusts phase.

Electronic Image Stabilization settings.

Sensitivity-Up selection.

Return each item on the camera setting screen to the factory default status.

Sets automatic operation of Auto-Pan, Preset sequence, Trace and Tour.

Assigns automatic functions to the

Auto key.

Sets the Auto-Pan operations.

Sets the preset sequence order.

Stores trace movements.

Sets the stop duration of trace movements.

MANUAL

ZOOM SCALABLE P/T

P/T LIMIT

P/T LIMIT SETTING

MAX P/T SPEED

FLIP

UP LIMIT

MAINTENANCE

INITIALIZE

REFRESH

PASSWORD

MOTOR POWER

FACTORY PRESET

AUTO ADJUST

DATA BACKUP

MOTION DETECTION *

3

PRIVACY MASK *

3

Individual settings.

Resets zoom interlocking.

Designate the pan and tilt rotation limits.

Sets the pan and tilt rotation limits.

Sets the maximum speed of pan and tilt operation.

Sets whether to set the tilt rotation range to

90 or over.

Sets the tilt angle limit.

Sets functions during maintenance.

Corrects deviation of stepping motor.

Corrects deviation of position.

Sets the password required when activating maintenance menu screen.

Improves deviation of preset position.

Returns all setting to initial status set by the factory.

Automatically corrects deviation of position.

Sets data writing and reading.

Sets motion detection.

Sets privacy masking area.

LANGUAGE Selecting the language.

* 1 Setting for this item can be entered by the Main Menu screen not by the Camera Menu screen when the equipments other than the C-RM500 are connected.

* 2 Can also be changed for individual positions at the Camera setting screen for individual positions.

* 3 Can be only set for the C-CC564, C-CC574, C-CC764 and C-CC774.

* 4 Can be only set for the C-CC564 and C-CC574.

* 5 Can be only set for the C-CC574 and C-CC774.

C-CC774/C-CC764/C-CC714

COMBINATION DOME CAMERA (OUTDOOR USE)

C-CC774 FEATURES

• 255 preset positions + Home position

• 420X zoom (optical 35X, electronic 12X)

• Electronic Image Stabilizer

• Tilt rotation range +5 ° to -185°(using Auto-Flip function)

• Pan rotation range continuous 360 °

• Pan/tilt maximum rotating speed is 360

°/sec

• 1/4 type CCD image device

• 540 lines high resolution

• Wide dynamic range

• Autofocus

• High-sensitivity function (color and B/W modes)

• Preset sequency function

• Privacy masking function

• Restricting camera movement

• Auto-trace function

• Auto-tour function

• Motion detection function

• Auto-pan function

• Preset image freeze function

• Dust/Water Protection: IP66

• RS-485 protocol compatible




• Tilt rotation range +5

° to -185°(using Auto-Flip function)


• Pan/tilt maximum rotating speed is 360 °/sec




• Autofocus












C-CC774

SPECIFICATIONS

Power source

Power consumption

24V AC 50/60Hz (2P loose end)

10W (normal operation), 80W max. (2.8A max.)

Control

Video Output

RS-485 communications system (new protocol compatible)

VBS 1.0V(p-p), 75 Ω, BNC-R jack

Camera Control Terminal RS-485 camera control connector, multi-pair cable 8P, loose end (3P of 8P)

Alarm Input 3 channels, no-voltage make contact input, open voltage: 18V DC, short-circuit current; Under 2mA (settable alarm action), multi-pair cable 8P, loose end (3P of 8P)

Auxiliary Contact Output 1 channel, open collector output, withstand voltage: 20V DC, permissible current: Under 100mA, multi-pair cable 8P, loose end (1P of 8P)

Synchronization Internal synchronization/power synchronization

(phase adjustable when in power synchronization mode)

ID

No. of Preset Positions 255 Positions + Home

Automatic Operation Auto-pan, Preset sequence, Auto-trace (2 preset patterns (60s)), Tour (16 preset patterns)

Timer

8 characters (alphanumeric and symbols)

Camera, Position, Trace, Auto-pan, Tour, Home, Alarm, Sector, AUX

Language

Refresh: Starts at the preset time every day or every week by timer settings

Program: Settable 16 actions

Menu: English, German, French, Italian

ID: English, German, French, Italian, Russian, Polish, Spanish, Portuguese

Camera

Image device

Resolution

S/N ratio

Minimum Illumination

1/4 type CCD

Horizontal: 540 lines typ. (at center), 520 lines min

50dB

High-sensitivity function 0FF: 1 lx (350mV), 0.3 lx (140mV)

High-sensitivity function 0N: 0.005 lx (350mV), 0.0015 lx (140mV)

(Sensitivity-UP)

High-sensitivity function 0FF: 0.5 lx (350mV), 0.15 lx (140mV)


Backlight Compensation WIDE DYNAMIC/WIDE DYNAMIC 2/Pattern 1/Pattern 2/Pattern 3/OFF

Dynamic Range 52dB (backlight compensation: WIDE DYNAMIC operation)

High-Sensitivity Function B/W mode and slow shutter mode (32 times max.)

White Balance ATW/AWB

Iris

Flicker Reduction

Electronic Zooming

Auto-Focus

Automatic

Automatic correction

12x zooming

One push/stop AF/continuous

Lens

Zooming

Zoom Speed

Pan/Tilt Head

35x

Effective Focal Length f = 3.4 – 119mm (35X)

Effective Angle of View Horizontal: 55.8

° (W) – 1.7° (T), Vertical: 43.3° (W) – 1.3° (T)

Maximum Aperture F 1.4 (W) – F 4.2 (T)

WIDE end to TELE end Approx. 2s (preset operation), Approx. 3.2s (manual operation)

Rotating Range

Rotating Speed

Panning: Endless 360 ° rotation, Tilting: +5° to –185°

Panning/Tilting: 360 °/s max. (preset operation), 360°/s max. (manual operation)

Other Function

Operating Temperature –40˚C to +50˚C

Operating Humidity Under 90% RH (no condensation)

Application

Auto-Pan, Freeze Preset, Manual Limit, Privacy Masking (up to 8),

Motion Detection (each 8 presets at each 4 positions) EIS

Dust/Water Protection

Finish

Indoors and outdoors (except seaside, industrial districts and locations exposed to fine particles, where the unit is subject to corrosion, and heights that expose the unit to strong wind pressure)

IP66

Dimensions

Weight

Accessory

Option

Case, top cover and decorative frame: PC resin, light gray,

Sunshade: Aluminum, light gray, paint, Dome cover: PC resin (transparent)

Camera section external diameter: ø230 × 340 (H)mm

Dome external diameter: ø 150mm

4.4kg

Top cover mounting screw (Hexagon socket screw M4 × 8) × 3,

CD-R (Camera controller software, manual (PDF)) × 1

Wall mounting bracket: C-BC711W, Suspension bracket: C-BC711P,

Pole mounting bracket: C-BC711PM, Smoked dome cover: C-A 711DM

C-CC764 SPECIFICATIONS

Power source


24V AC, 50/60Hz (2P loose end)


Control RS-485 communications system (new protocol compatible)

Video Output VBS 1.0V(p-p), 75 Ω, BNC-R jack






ID



Timer



Language





Camera

Image device

Resolution

S/N ratio


1/4 type CCD

Horizontal: 480 lines (at center)

50dB

High-sensitivity function 0FF: 3 lx (350mV), 1 lx (140mV)


Backlight Compensation WIDE DYNAMIC/Pattern 1/Pattern 2/Pattern 3/OFF




Iris



Auto-Focus

Automatic


12x zooming


Lens

Zooming 23x

Effective Focal Length f = 3.6 – 82.8mm (23X)

Effective Angle of View Horizontal: 54 ° (W) – 2.5° (T), Vertical: 41.6° (W) – 1.9° (T)


Zoom Speed WIDE end to TELE end

Approx. 1.5s (preset operation), Approx. 2.9s (manual operation)

Pan/Tilt Head

Rotating Range

Rotating Speed

Panning: Endless 360

Panning/Tilting: 360

° rotation, Tilting: +5° to –185°

°/s max. (preset operation), 360°/s max. (manual operation)

Other Function



Application

Auto-Pan, Freeze Preset, Manual Limit, Privacy Masking (up to 8),

Motion Detection (each 8 presets at each 4 positions)


Finish


IP66

Dimensions

Weight

Accessory

Option

Case, top cover and decorative frame: PC resin, light gray

Sunshade: Aluminum, light gray, paint

Dome cover: PC resin (transparent)

Camera section external diameter: ø230 × 330.5 (H)mm


4.4kg









° to -90°





• Autofocus

• High-sensitivity function (color mode)








Brackets and Dome Cover

C-BC711P

Suspension Bracket

The C-BC711P is exclusively designed to be used to suspend TOA's outdoor combination camera from a ceiling or eaves.

Finish Base: Aluminum, light gray, paint

Pipe: Stainless steel (SUS304)

Dimensions 140 (W) × 164 (H) × 200 (D)mm

Weight

Accessory

1kg

Camera mounting screw (M5 ×12, with washer) × 3

Note: pay attention to the strength of the attaching portion.

C-BC711PM

Pole Mounting Bracket

Using the optional YS-60B and C-BC711W, the C-BC711PM can mount the outdoor combination camera on a pole.

Finish Stainless steel (SUS304)

Dimensions 140 (W) × 200 (H) × 60 (D)mm

Weight 700g

Note: Reinforce the pole mounting bracket and mounting band separately for security when installing the camera in locations exposed to vibration or strong winds.

Maintenance the unit, mounting bracket and mounting band periodically to ensure that there are no loose joint nor rickety parts.


Power source


24V AC, 50/60Hz (2P loose end)


Control

Video Output








ID



Timer



Language





Camera

Image device

Resolution

S/N ratio


1/4 type CCD


50dB



Backlight Compensation Pattern 1/Pattern 2/Pattern 3/OFF

High-Sensitivity Function Slow shutter mode (32 times max.)

White Balance

Iris

ATW/AWB

Automatic



Auto-Focus

Lens


12x zooming


Zooming 22x



° (W) – 2.2° (T), Vertical: 36.5° (W) – 1.7° (T)




Pan/Tilt Head

Rotating Range

Rotating Speed





Other Function Manual Limit


Operating Humidity

Application


Finish

Under 90% RH (no condensation)


IP66

Dimensions

Weight

Accessory

Option

Case, top cover and decorative frame: PC resin, light gray

Sunshade: Aluminum, light gray, paint

Dome cover: PC resin (transparent)

Camera section external diameter: ø230 × 330.5 (H)mm


4.4kg





C-BC711W

Wall Mounting Bracket

The C-BC711W is designed to be used to mount TOA's outdoor combination camera on a wall.

Finish Base: Aluminum, light gray, paint

Pipe: Stainless steel (SUS304)

Dimensions 140 (W) × 240 (H) × 188.1 (D)mm

Weight 1.3kg

Accessory Camera mounting screw (M5 ×12, with washer) × 3

Note: pay attention to the strength of wall surface.

C-A711DM

Smoked Dome Cover

The C-A711DM Smoked Dome Cover is specially designed to be used in conjunction with TOA's Combination Cameras.

The Dome Cover is used to make it difficult for individuals to see the camera's orientation.

Transmissivity Approx. 30%*

Finish Dome: PC resin, smoked

Frame: PC resin, light gray

Dimensions ø219.8 × 128 (H)mm

(Dome external diameter: ø150mm)

Weight 400g

*As a general guideline, the minimum object illumination of the camera equipped with the Smoked Dome Cover is approximately 3.3 times that of the camera without the cover.

Note: Be careful when installing the camera with this cover in low illumination location as the cover may cause camera sensitivity to decrease.

C-CC574/C-CC564/C-CC514

COMBINATION DOME CAMERA (INDOOR USE)




• Electronic Image Stabilizer

• Tilt rotation range +5 ° to -185°

(using Auto-Flip function)



°/sec




• Autofocus















° to -185°

(using Auto-Flip function)






• Autofocus











C-CC574

SPECIFICATIONS

Power source


24V AC 50/60Hz


Control

Video Output



Camera Control Terminal RS-485 camera control connector

Alarm Input

Auxiliary Contact Output 2 channels, open collector output, withstand voltage: 20V DC, permissible current: Under 100mA, relay contact output, permissible voltage: 20V DC, permissible current: Under 1A

Synchronization

8 channels, no-voltage make contact input, open voltage: 18V DC, short-circuit current; Under 2mA (settable alarm action)

ID

Internal synchronization/Power synchronization






Timer

Language





Camera

Image device

Resolution

S/N ratio


1/4 type CCD

Horizontal: 540 lines typ. (at center), 520 lines min

50dB



(Sensitivity-UP)

High-sensitivity function 0FF: 0.5 lx (350mV), 0.15 lx (140mV)


Backlight Compensation WIDE DYNAMIC/WIDE DYNAMIC 2/Pattern 1/Pattern 2/Pattern 3/OFF




Iris



Auto-Focus

Automatic


12x zooming


Lens

Zooming 35x



° (W) – 1.7° (T), Vertical: 43.3° (W) – 1.3° (T)


Zoom Speed WIDE end to TELE end Approx. 2s (preset operation),

Approx. 3.2s (manual operation)

Pan/Tilt Head

Rotating Range

Rotating Speed





Other Function Auto-Pan, Freeze Preset, Manual Limit, Privacy Masking (up to 8),

Motion Detection (each 8 presets at each 4 positions), EIS

Operating Temperature –10˚C to +50˚C (continuously active for operation at temperature below 0 °C)


Application

Finish

Indoor used

Dimensions

Weight

Accessory

Option

Base: PC/ABS resin, cool gray, Camera: PC/ABS resin, black

ø168 × 234 (H)mm

1.7kg

Camera mounting screw × 4, Safety wire × 1,


Ceiling mount cover: C-BC511C, C-BC511C-S

Flush ceiling mounting bracket: C-BC511U, C-BC511U-S

Ceiling suspension bracket: C-BC511P, Wall mounting bracket: C-BC511W

Ceiling mounting bracket: C-BC511A


Power source


24V AC, 50/60Hz


Control

Video Output




Alarm Input

Auxiliary Contact Output 2 channels, open collector output, withstand voltage: 20V DC, permissible current: Under 100mA, relay contact output, permissible voltage: 110V DC, 125V AC, permissible current: Under 1A

Synchronization

8 channels, no-voltage make contact input, open voltage: 18V DC, short-circuit current; Under 2mA (settable alarm action)

ID

Internal synchronization/Power synchronization




No. of Preset Positions 255 Positionss + Home


Timer

Language





Camera

Image device

Resolution

S/N ratio


1/4 type CCD


50dB

High-sensitivity function 0FF: 3 lx (350mV), 1 lx (140mV)


Backlight Compensation WIDE DYNAMIC/Pattern 1/Pattern 2/Pattern 3/OFF




Iris



Auto-Focus

Automatic


12x zooming


Lens

Zooming 23x

Effective Focal Length f = 3.6 – 82.8mm (23X)

Effective Angle of View Horizontal: 54 ° (W) – 2.5° (T), Vertical: 41.6° (W) – 1.9° (T)




Pan/Tilt Head

Rotating Range

Rotating Speed





Other Function Auto-Pan, Freeze Preset, Manual Limit, Privacy Masking (up to 8),

Motion Detection (each 8 presets at each 4 positions)



Application

Finish

Indoor used

Dimensions

Weight

Accessory

Option

Base: PC/ABS resin, cool gray

Camera: PC/ABS resin, black

ø168 × 234 (H)mm

1.7kg





Ceiling suspension bracket: C-BC511P

Wall mounting bracket: C-BC511W





• Tilt rotation range +5 ° to -90°



°/sec



• Autofocus

• High-sensitivity function (color mode)








Power source


24V AC, 50/60Hz

9W (normal operation), 19W max. (1.3A max.).

Control

Video Output




Alarm Input 3 channels, no-voltage make contact input, open voltage: 18V DC, short-circuit current; Under 2mA (settable alarm action)

Auxiliary Contact Output 1 channel, open collector output, withstand voltage: 20V DC, permissible current: Under 100mA



ID

No. of Preset Positions 255 Positionss + Home


Timer



Language





Camera

Image device

Resolution

S/N ratio


1/4 type CCD


50dB



Backlight Compensation Pattern 1/Pattern 2/Pattern 3/OFF

High-Sensitivity Function Slow shutter mode (32 times max.)

White Balance

Iris

ATW/AWB

Automatic



Auto-Focus

Lens


12x zooming


Zooming 22x



° (W) – 2.2° (T), Vertical: 36.5° (W) – 1.7° (T)




Pan/Tilt Head

Rotating Range

Rotating Speed





Other Function Manual Limit



Application

Finish

Indoor used

Dimensions

Weight

Accessory

Option

Base: PC/ABS resin, cool gray

Camera: PC/ABS resin, black

ø168 × 234 (H)mm

1.7kg





Ceiling suspension bracket: C-BC511P

Wall mounting bracket: C-BC511W


Brackets and Dome Covers

Finish

Dimensions

Weight

Accessory

C-BC511A

Ceiling Mounting Bracket

The C-BC511A is specially designed to mount TOA's Combination

Cameras directly on the ceiling. The bracket facilitates mounting of the camera on the plasterboard in the double ceiling or other locations where the mounting screws cannot be installed securely.

Surface-treated steel plate, black, paint

132 (W)

× 30 (H) × 70 (D)mm

160g

Camera mounting screw

× 4, Safety wire × 1, Pattern paper × 1

C-BC511C

Ceiling Mount Cover

The C-BC511C is a camera installation cover designed solely for mounting TOA's

Combination Cameras. The cover is used when mounting the Combination camera directly to a ceiling or wall or suspending it from the ceiling.

Finish

Dimensions

Weight

Case: PC/ABS resin, cool gray, Dome cover: Acrylic resin, transparent

ø168 × 182.2 (H)mm (Dome external diameter: ø125mm)

220g

C-BC511C-S

Ceiling Mount Cover (Smoked)

The C-BC511C-S is a camera installation cover designed solely for mounting

TOA's Combination Cameras. The cover is used when mounting the Combination camera directly to a ceiling or wall or suspending it from the ceiling. The cover is used to make it difficult for individuals to see the camera's orientation.


Finish

Dimensions

Weight

Case: PC/ABS resin, cool gray, Dome cover: Acrylic resin, smoked

ø168

× 182.2 (H)mm (Dome external diameter: ø125mm)

220g

*As a general guideline, the minimum object illumination of the camera equipped with the Ceiling Mount Cover is approximately 5 times that of the camera without the cover.

Note: Be careful when installing the camera with this cover in low illumination location as the cover may cause camera sensitivity to decrease.

C-BC511U

Flush Ceiling Mounting Bracket

The C-BC511U bracket is designed to be exclusively used for flush ceiling mounting of TOA's combination camera. Use this bracket when mounting the camera to the ceiling surface where the fixing screws cannot be securely installed, such as on the plaster panel of the dual-construction ceiling. Also, use this bracket to minimize the exposure of the camera.

Finish

Dimensions

Weight

Accessory

Bezel: PC/ABS resin, cool gray, Dome cover: Acrylic resin, transparent, Bracket: Aluminum, black, paint.


ø250

× 282.7 (D)mm (Dome external diameter: ø125mm)

1.2kg

Safety wire × 1, Pattern paper × 1

C-BC511U-S

Flush Ceiling Mounting Bracket (Smoked)

The C-BC511U-S bracket is designed to be exclusively used for flush ceiling mounting of TOA's combination camera. Use this bracket when mounting the camera to the ceiling surface where the fixing screws cannot be securely installed, such as on the plaster panel of the dual-construction ceiling. Also, use this bracket to minimize the exposure of the camera. The bracket is used to make it difficult for individuals to see the camera's orientation.


Finish

Dimensions

Bezel: PC/ABS resin, cool gray, Dome cover: Acrylic resin, smoked, Bracket: Aluminum, black, paint,


ø250

× 282.7 (D)mm (Dome external diameter: ø125mm)

Weight

Accessory

1.2kg

Safety wire × 1, Pattern paper × 1

* As a general guideline, the minimum object illumination of the camera equipped with the Flush Ceiling Mounting Bracket is approximately

5 times that of the camera without the bracket.

Note: Be careful when installing the camera with this bracket in low illumination location as the cover may cause camera sensitivity to decrease.

C-BC511P

Ceiling Suspension Bracket

The C-BC511P is a Ceiling Suspension Bracket designed solely for suspending

TOA's Combination Cameras from the ceiling.

Finish

Dimensions

Weight

Accessory

Top cover: PC/ABS resin, cool gray, Pipe: Stainless steel (SUS304).

Bracket: Surface-treated steel plate, black, paint

ø150

× 233mm

1.2kg

Top cover

× 4, Safety wire × 1, Pattern paper × 1

C-BC511W

Wall Mounting Bracket

The C-BC511W Wall Mounting Bracket is specially designed to mount

TOA's Combination Cameras to wall surfaces. Install the unit only in a location that can structurally support weight of the unit and camera.

Finish

Dimensions

Weight

Accessory

Top cover: PC/ABS resin, cool gray, Pipe: Stainless steel (SUS304).

Bracket: Surface-treated steel plate, black, paint

150 (W)

× 203 (H) × 203 (D)mm

1.1kg

Top cover

× 4, Safety wire × 1, Paper pattern × 1

C-RM500

REMOTE CONTROLLER

C-RM1000

REMOTE CONTROLLER

The C-RM500 Remote Controller is designed for use in camera-based systems that allow remote control from up to 1.2km away over RS-485 communication lines. It allows video images to be switched remotely and can handle a maximum of 16 TOA's Combination Dome Cameras when used together with the TOA Multiplexer. Easy-to-see LEDs inform status of control, alarm, focus and other functions.

FUNCTIONS

• Control up to 16 TOA's

Combination Dome Cameras

• Instant position recall

• Controls Multiplexer

• Alarm capability

• 2 Location Control

The C-RM1000 Remote Controller is used to remotely control the

9-CH/16-CH Digital Video Recorder (C-DR091/161 Series). It can also control combination cameras connected to the Digital Video Recorder.

A built-in 3-axis joystick allows main operations to be performed with one hand.

FUNCTIONS

• Digital Video Recorder Control

• Screen Display Operation

• Combination Dome Camera

Operation

• Preset Position Programming and Playback

• Quick Display Function

• Function Programming

• Digital Video Recorder Grouping

• Password Setting

• Monitor Locking

• Web Functions

APPEARANCE AND DIMENSIONAL DIAGRAM

326

10˚

57.9

APPEARANCE AND DIMENSIONAL DIAGRAM

25 31.7

185.2

323.6

56.8

10 °

65

Figure of the installed unit

SPECIFICATIONS

Power Source 12 V DC

Current Consumption 150 mA

Slave Remote Controller RS-485, screwless connector

Camera Control RS-485, screwless connector (* 1 )

Switcher Control

Alarm Input

Alarm Output/

Control Input

RS-485, screwless connector

RS-232C, D-sub connector (9 pins, male)

RS-232C, D-sub connector (9 pins, male)

Alarm output: 16 channels, NPN open collector output, withstand voltage: 30 V DC, control current: 20 mA

Alarm input: 1 channel, no-voltage make contact input, open voltage: 5 V DC, short-circuit current: 5 mA max.

Home position selection input:

1 channel, no-voltage make contact input, open voltage: 5 V DC, short-circuit current:

5 mA max.

D-sub connector (25-pins, female)

Display LED indication of control status, alarm status, alarm hold status, still picture status, defroster, auxiliary setting, auto, auto focus, and lens speed

LCD indication of key entry confirmation

Continuous alarm tone (can be turned on and off) Alarm Signal

Number of Unit

Connections

Up to 2 (one to be set for MASTER unit, another for

SLAVE unit)

1.2 km (* 2 ) (between the Remote controller and the Maximum Cable

Distance Combination cameras)

Operating Temperature 0 °C to +50°C

Operating Humidity Under 90% RH (no due condensation produced)

Finish

Dimensions

Weight

Accessory

Applicable Model

(option)

Panel: Surface-treated steel plate, sand gray, paint

Sides: Rubber

326 (W) × 62 (H) × 185.2 (D) mm

1.8 kg

D-sub connector (9 pins, male) × 1,

D-sub connector(25 pins, male) × 1

Combination dome camera: C-CC504S/554S/514/564/574/

C-CC714/764/774

Switcher: C-MS161D, C-MS91D

Slave remote controller: C-RM500

Interface unit: C-IF500

Alarm unit: C-AL80

(*

(*

1

2

) Can connect up to 31 units mixing with combination cameras and interface units.

) Applies to the system where the unit and combination camera are connected in a matched pair.

Represents the total of connected cable distances if multiple combination cameras or interface units are connected in the system (when the CPEV-S cable thicker than 0.65 mm in diameter is used).

181

Figure of the unit installed

SPECIFICATIONS

Power Source 12V DC (Supplied from the included AC adapter or from the digital video recorder)

80mA (use of the supplied AC adapter) Power Consumption

Digital Video Recorder

Control

Alarm Signal

Maximum Cable Distance

RS-485, RJ-11 (6P6C)

(when the included 5-meter modular cable is used)

RS-485 screwless connector (3 pins)

(with cable length of 3 meters and more, or when C-RF1000 is used)

Continuous alarm tone (can be turned on and off through the menu)

1.2km*

Function

Operating Temperature

Operating Humidity

Password setting, DVR Group setting, Abbreviation function (512 types),

Preset position setting, Language choice (English/French)

0 °C to +40°C

Under 80% RH (no dew condensation)

Finish

Dimensions

Panel: Surface treated steel plate, silver, painted

Sides: Rubber

323.6 (W) × 112.7 (H) × 181 (D) mm

Weight

Accessories

1.6kg (excluding AC adapter)

AC adapter (1.8m) × 1, Modular cable (3m) × 1

Applicable Model (option) Digital Video Recorder: C-DR091/C-DR161 Series

Interface Unit: C-RF1000

* Appllies to the system where the unit and a digital video reccorder are connected in a matched pair.

Represents the total of connected cable distances if multiple digital video recorders or Interface units are connected int the system.

C-IF500

INTERFACE UNIT

C-AL80

ALARM UNIT

A useful option for configuring camera systems, the C-IF500 functions as a splitter. It provides control over expanding a camera system when the distance is over 1.2km (max. 3km) between the dedicated C-RM500 Remote Controller and system cameras linked to it. It will also allow configuring a star connection. Receiving the

RS-485 communication line serial signals, the C-IF500 splits the signals into 4-channel data for slave units and converts into

RS-232C data to be used for public line or fiber optics communication. Data communication between master and slave terminals is bidirectional. The C-IF500 also allows easily setting the data communication speed by DIP switch to suit network requirements.

The C-AL80 Alarm Unit serves as the main controller for the alarm requirements of a system by converting alarm signals initiated by externally connected equipment into RS-232C-compatible signal data. In addition to its 32 alarm or remote inputs, the C-AL80 can also be linked to a maximum of 8 other C-AL80 units in master/ slave configurations. This provides a total of 256 alarm or remote inputs to be transmitted to the C-RM500 remote controller.

APPEARANCE AND DIMENSIONAL DIAGRAM APPEARANCE AND DIMENSIONAL DIAGRAM

210

284.1

279.8

420

335.8

319.8

Front cover

11

Enlarged figure for the inside of a front cover

Unit: mm

Unit: mm

SPECIFICATIONS

Power Source 12 V DC

Current Consumption 100 mA

External Control

Display

Maximum Cable

Distance

Master: RS-485, screwless connector terminating resistance (100 Ω) switch ON/OFF

Slave(* 1 ): 4 channel, RS-485, screwless connector

RS-232C, D-sub connector (9-pin, male)

Power LED indicator, communication LED indicators

(TX, RX)

RS-485: 1.2 km (* 2 )

RS-232C: 10 m

Communication Speed 4800 bps, 9600 bps, 19200 bps, 38400 bps

Operating Temperature -10 °C to +50°C

Operating Humidity Under 90% RH (no due condensation produced)

Finish Panel: Aluminum, black, 30% gloss, paint

Case: Pre-coated steel plate, 30% gloss, black

Dimensions

Weight

Option

210 (W) x 46 (H) x 284.1 (D) mm

1.4 kg

Rack mounting bracket:

M-15B-BK (for rack mounting one C-IF500 unit)

MB-15B-J (for rack mounting two C-IF500 units)

(* 1 ) Communications cannot be made between slave terminals.

Each slave terminal can connect up to 31 cameras. (except RS-232C port)

(* 2 ) Applies to the system where the unit and combination camera are connected in a matched pair.

Represents the total of connected cable distances if multiple combination cameras or Interface units are connected in the system (when the CPEV-S cable thicker than 0.65 mm in diameter is used).

SPECIFICATIONS

Power Source 220 – 240 V AC, 50/60 Hz

Power Consumption under 6 W (60mA)

Alarm/Remote Input 32 channels, no-voltage make contact input, open voltage: 5 V DC, short-circuit current: max. 5 mA, M3 screw terminal, distance between barriers: 7.62 mm

Control Input/Output 1 channel, RS-232C, D-sub connector (9 P, male)

(only valid for master unit), fixed to 38,400 bps

Master/sub Connection 2 channels, RS-485, maximum cable length: 1200m,

Terminal DIN connector (5 P)

Alarm Reset Input 1 channel, no-voltage make contact input, open voltage: 5 V DC, short-circuit current: max. 5 mA, D-sub connector (25 P)

Setting Switches Master/Slave: 3-bit DIP switch

(Selection of Master or Slave 1—7)

Alarm/Remote: 1-bit DIP switch

(Alarm/Remote selection)

Alarm time: 1-bit DIP switch (Edge/Level selection)

RS-485 terminal: Rear-mounted slide switch (RS-485 termination, Enable/Disable selection)

Application

Dimensions

Indoor use

Operating Temperature 0 °C to +40°C

Finish Panel: Aluminum extrusion, black, 30% gloss

Case: Pre-coated steel plate, black, 30% gloss

420 (W) × 96.6 (H) × 335.8 (D) mm

Weight

Accessory

Option

3.6 kg

DIN plug × 2, RS-232C cable (2 m) × 1, D-sub connector (25 P) × 2, Power cord (2 m) × 1

Rack mounting bracket: MB-23B

Application Model Remote controller: C-RM500

C-CC774/C-CC764/C-CC714

APPEARANCE AND DIMENSIONAL DIAGRAM

C-BC711W C-CC774

ø180

Multi-pair cable 8 P, loose end

Cable end: 2 P loose end

Power cord length

Approx. 1.8 m

BNC-R jack

Coaxial cable length

Approx. 1.8 m

Multi-pair cable length

Approx. 1.8 m

Safety wire length

Approx. 20 cm

140

100 4–ø11.4

279

Applicable camera

Wall mounting example

(option)

ø150

ø218.5

ø230

30 opening for cable entry ø24

Hook to connect safety wire

164

188.1

17

ø48.3

C-CC764/C-CC714

ø179.9

Multi-pair cable 8 P, loose end

Cable end: 2 P loose end

Power cord length

Approx. 1.8 m

BNC-R jack

Coaxial cable length

Approx. 1.8 m

Multi-pair cable length

Approx. 1.8 m

Safety wire length

Approx. 20 cm

C-A711DM

ø150

ø218.5

ø230

ø219.8

Safety wire fixing screw

C-BC711P

Hook to connect safety wire

30

20

ø48.3

140

100 4–ø11.4

Cable entry hole on a ceiling ø50

Applicable camera

(option)

Ceiling mounting example

C-BC711PM

57.6˚

140

100

ø80

Wall mounting bracket

C-BC711W (option)

Applicable camera

(option)

Pole mounting bracket

YS-60B (option)

Pole

ø90–

ø340

A

10 30

Figure as viewed from point A

Mounting example

4–ø11

Unit: mm

C-CC574/C-CC564/C-CC514

APPEARANCE AND DIMENSIONAL DIAGRAM

C-CC574C-CC564/C-CC514

4–ø4.5

Connector 1

BNC jack

60

Power supply terminal block

C-BC511A

13x35

(Anchor bolt mounting hole)

4–ø7

(Safety wire mounting hole)

4–ø4.5

(Electric work box mounting hole)

4–M4

(Camera mounting hole)

ø118

ø168

C-BC511C (option) or C-BC511C-S (option)

(View of an optional camera installation cover attached)

■INSTALLATION EXAMPLE

Mounting to a heavy-duty ceiling (such as a concrete ceiling)

1. When routing both the coaxial, power cables and signal cable from the speaker side.

2. When routing both the coaxial, power cables and signal cable from the ceiling panel.

ø80–ø90

Note: For anchor bolts, use the unit driving type female screws (M4).

Camera center

60

Anchor bolt

(female screw) mounting distance

C-BC511C/C-BC511C-S

ø125

ø168

ø168

Mounting

C-BC511C

C-BC511U/C-BC511U-S

228

Cable entry hole

2–10x20

(Safety wire mounting hole)

10x20

(Anchor bolt mounting hole)

4–ø6

Cable entry hole

Applicable camera

(option)

Safety wire (accessory)

(Connect this wire to an object other than the bracket.)

83.5

122

132

Anchor bolt

C-BC511A

Camera mounting screw (accessory)

ø140 – 145mm

(Mounting hole

in the ceiling)

Ceiling board

*When routing the wiring to the attic if the unit is used in conjunction with the N-CC2564.

the ceiling panel must be

9 – 40mm in thickness.

Ceiling mounting


Applicable camera

(option)

C-BC511P

4–ø5

(Ceiling mounting hole)

40

81

Drop prevention screw

(M5)

Note: When extending a pipe, use a commercial “88” stainless steel wound pipe or copper sheet wire tube (ø48.3 mm).

(In this event, make holes as illustrated.)



ø150

60

ø48.3

“C” channel bracket

Ceiling board

Ceiling hole

Top cover

(accessory)

Drop prevention screw

(M5) C-BC511C (option) or

C-BC511C-S (option)

4–M4

(Ceiling mountion hole)

Applicable camera

Ceiling mounting

(option)

Note: The mounting hole in the ceiling is

ø40–ø50 mm in diameter.

C-BC511W

ø125

ø250



Anchor bolt

C-BC511U

Ceiling board

Applicable camera

(option)

Note: The mounting hole

Ceiling mounting in the ceiling is

ø232–ø236 mm in diameter.

4–ø5

(Wall mounting hole)

81

40

ø48.3

ø150

203

128

C-BC511W

60

4–M4

(Camera mounting hole)


Applicable camera

(option)

Wall mounting

Unit: mm

SYSTEM EXAMPLES

1. Combination Dome Camera (1 unit)

Combination

Dome Cameras

C-CC564

Remote Controller

C-RM500

Monitor

2. Combination Dome Camera (16 units)

Combination

Dome Cameras

C-CC564

Remote Controller

C-RM500 max.

16 C-MS161D

Multiplexer

Monitor

3. When Combination Dome Camera and Remote

Controller are separated by more than 1.2km.

max. 3km

Combination

Dome Cameras

C-CC564

C-IF500

Interface Unit

C-IF500

Interface Unit

Remote Controller

C-RM500

CC-3331B

Cable Compensator

Monitor

4. Sensor-activated Dome Camera operation.

Sensor max. 8

Combination

Dome Cameras

C-CC564 max. 3 max. 3

C-CC514

C-CC764

C-MS161D

Multiplexer

Sensor max. 256

Remote Controller

C-RM500

RS-232C

Monitor

C-AL80

C-AL80

Alarm Unit

C-AL80

5. Digital Video Recorder System

Combination

Dome Camera

C-CC564

Combination

Dome Camera

C-CC764

Digital Video Recorder

C-DR161 Series

C-DR091 Series

Remote Controller

C-RM1000

Monitor

Digital Video Recorder

C-DR161 Series

C-DR091 Series

Remote Controller

C-RM1000

TOA Corporation

URL : http://www.toa.jp/

Specifications are subject to change without notice.

Printed in Japan (0701) 833-52-344-2B u

TOA C-BC711W Specification Sheet

COMBINATION

DOME CAMERA SYSTEMS

For Outdoor Use

Combination Dome Cameras

For Indoor Use

Brackets and Covers

Remote Controllers

C-RM500

C-RM1000

Configuring a perfect surveillance system.

Higher resolution delivers better images.

All points coverage at high speed.

Intelligent image optimizing using the Wide

Dynamic Range function.*

Expanded zooming ability.

Electronic Image Stabilizer.*

Sophisticated autofocus modes add versatility.

Motion detection function initiates operation.*

Color image clarity maintained with sensitivity boost.

FEATURES

Day/Night operation improves low light performance.*

Protecting privacy.

Outdoor installation ready.

(meets IP66 standards)

Withstands cold weather conditions.

Route tracing facilitates subject monitoring.

Configuring programmable tours.

Programmable camera operation initiated by alarm input.

Preset operation start with Timer program function.

FEATURES

Titling options.

Flexible installation options.

Software for maintenance.

Freeze preset function*

Multi-language

Auto positional deviation correction

Auto Refresh Function

Other functions.

Combination Dome Camera Comparison Table

SETTING GUIDE

COMBINATION DOME CAMERA (OUTDOOR USE)

Brackets and Dome Cover

C-BC711P

C-BC711PM

C-BC711W

C-A711DM

COMBINATION DOME CAMERA (INDOOR USE)

Brackets and Dome Covers

REMOTE CONTROLLER

REMOTE CONTROLLER

INTERFACE UNIT

ALARM UNIT

APPEARANCE AND DIMENSIONAL DIAGRAM

APPEARANCE AND DIMENSIONAL DIAGRAM

1. Combination Dome Camera (1 unit)

2. Combination Dome Camera (16 units)

3. When Combination Dome Camera and Remote

Controller are separated by more than 1.2km.

4. Sensor-activated Dome Camera operation.

5. Digital Video Recorder System

Related manuals

TOA

C-BC711P

TOA

C-BC511U-S

TOA

C-BC771PM

TOA

MB-WT1

TOA

C-A771DM

TOA

C-BL20

TOA

C-BC511U

TOA

C-CC564 NT

TOA

C-BC711W