AT&T 1185 User manual

I N S TA L L AT I O N

Table/Desk Installation

¥

NOTE: Install this telephone away from electronic equipment, such as personal computers,television sets or microwave ovens. Avoid excessive heat,cold, dust or moisture.

1 Connect the corded handset to the base.

2 Connect the telephone line cord. (figure a)

3 Connect the power cord to the base and an electrical outlet not controlled by a wall switch. (figure a) The answer ON/OFF light goes on, and CL flashes in the message window.

Use only the power cord supplied with this p ro d u c t . If you need a re p l a c e m e n t , call 1-800-

2 2 2 – 3 1 1 1 .

4 Check for dial tone .

• Lift the handset, you should hear a dial tone.

¥

NOTE: For Wall Mount Installation see page 5 in the

User Manual.

Handset Charger Installation

1 Connect the power cord. Be sure to plug the cord into an electrical outlet not controlled by a wall switch.

2 Install the handset batter y. Use NiCd Replacement

Battery 3301,SKU# 91076. (figure b)

3 Charge the handset batter y.

• Place the handset in the remote charging stand.The CHARGING light goes on.

• Charge the battery at least 12 hours.

4 Check for dial tone.

• After the batteries are charged,lift the handset and press ; you should hear a dial tone.

QUICK START GUIDE

2.4 GHz Corded Cordless

Telephone with Caller ID/Call

Waiting 1485/1185

Standard electrical outlet

Modular telephone jack

Power Cord figure a figure b a) Remove battery compartment cover by pressing on the indentation and sliding downward.

Line Cord c) Place battery pack in compartment with the wires in the lower left corner, along the bottom of the battery pack.

b) Align two holes in plug with socket pins, and snap the plug into place.

d) Replace cover by sliding it up into place.

F E ATURE SETUP

Set the time and date displayed on handset screen

If you subscribe to Caller ID service, the date and time will be set automatically with the first incoming call.

If you do not have Caller ID service, you can set the date and time manually.

• Press , then press until displayed. Press .

• The month is flashing. Use or to select the current month. Press .

is

• The day is flashing. Use or to select the correct day. Press .

•

• The hour is flashing. Use or to select the current hour. Press .

• The minute is flashing. Use or to select the correct minute. Press .

or is flashing. Use or between and . Press .

to choose

Set the phone for tone or pulse dialing (base only)

• Press on base.

• Press or until setting is displayed,then press and the current

.

• Use or to select the correct setting.

• Press to save the setting.

Set the language

• Press handset.

on the base or on the

• Press or until

• Press is displayed.

, the current setting is flashing.

or • Use or to select

.

• Press to save the setting.

,

© 2003 Advanced American Telephones.

All Rights Reserved.

AT&T and the Globe Design are trademarks of AT&T Corp., licensed to

Advanced American Telephones.

Printed in China. Issue 1AT&T 05/03

Answering System

P ress to turn the system on or off. When the system is on, you will hear “Machine on” and the ON/OFF light will be lit.

If you turn the system on at the first time, it works using the default setting and pre - re c o rded outgoing announcements. For details on re c o rding your own outgoing announcements and changing system s e t t i n g s , see “ANSWERING SYSTEM OPERATION

AT T H E BA S E

” starting on page 24 of your User’s Manu a l .

Set the Clock

1 Make sure the answering system is on.

2 Press .The system announces the clock setting then announces:“To change clock, press

.”

3 Press .

4 Press until the system announces the correct day, then press .

5 Press until the system announces the correct hour, then press .

6 Press until the system announces the correct minutes,then press .

7 Press until the system announces the correct years,then press . The system announces the current clock setting.

¥

NOTE:You can choose to set the day and time manually, or you can allow it to be set automatically with incoming Caller ID Information.

¥

NOTE: Press and hold to advance the minute or the year by 10.

¥

NOTE: The selection of the year is from 2000 to 2039.

Record Your Announcement

¥

NOTE: For complete details about recording announcements, see “Record Your Announcement” in the ANSWERING SYSTEM OPERATION section of your User’s Manual.

1 With the system set for the desired answer mode

(normal or Announce Only) press until you hear “Change announcement.”

2 Press . After you hear “ N ow re c o rd i n g ” followed by a beep, speak toward the base to record an nnouncement up to 90 seconds long.

3 Press any MAILBOX/STOP button to stop recording. The system plays back your recorded message.