Bajaj Electricals DB30 User's Manual

DB30 Doodle Bug Mini Bike
Read this manual carefully. It contains important safety information.
No one under the age of 16 should operate this Mini Bike without adult supervision.
OWNER’S MANUAL
Minimum Age Requirement: 16
Weight capacity: 200 lbs.
Rev. D
Always wear a helmet; It could save your Life!
Please obtain, review, and follow provincial / municipal government acts and regulations pertaining to owning and operating an off-road vehicle.
Congratulations on your purchase of the Baja
Motorsports DB30 Doodle Bug Mini Bike.
Your Mini bike is warranted to be free of manufacturing defects in
the material of workmanship for a period of 90 days from the date
of purchase. During the warranty period BAJA MOTORSPORTS, LLC
will at its option, repair, provide replacement parts or replace your
Baja Motorsports DB30 Doodle Bug Mini Bike at no charge. This
warranty does not cover normal wear items or damage caused by
neglect or misuse of the product.
Engine Warranty – 90 days
Frame Warranty – 90 days
Warranty is void if:
Frame is bent or broken due to abuse
If wheels are bent or broken
Fender bent or broken due to abuse
Any sign of impact, accident, jumping, spin-outs or roll over.
Should you experience a problem or need to return your Baja Motorsports DB30 Doodle Bug
Mini Bike for repair, please call the BAJA MOTORSPORTS customer service department TOLL
FREE at 1-888-863-BAJA (2252) between the hours of 7am and 5pm Monday thru Friday PST
and Saturday 8am to 4pm PST. During DST hours change to MT. You will be instructed how to
proceed.
A COPY OF THE SALES RECEIPT IS REQUIRED.
ii
!
WARNING
This manual should be considered as a permanent part
of the vehicle and should remain with the vehicle when
resold or otherwise transferred to a new user or operator.
The manual contains important safety information
and instructions which should be read carefully before
operating the vehicle. All operators should obtain, review,
and follow provincial and municipal government acts and
regulations pertaining to owning and operating an offroad vehicle. Children under the age of 16 should never
operate this vehicle.
iii
table of contents
SAFETY ----------------------------------------------------- 2
Safe Operation ------------------------------------ 3
Safety Gear ----------------------------------------- 4
Location of Labels -------------------------------- 5
SPECIFICATIONS ----------------------------------------- 6
LOCATION OF PARTS ----------------------------------- 7
OPERATION ----------------------------------------------- 8
Left and Right Hand Grip ----------------------- 8
Engine ON/ OFF switch and Pull Cord ------ 8
Fuel Fill ---------------------------------------------- 9
Fuel Valve ------------------------------------------- 9
INSPECTION BEFORE RIDING ------------------------- 10
ENGINE STARTING AND STOPPING ----------------- 11
INSPECTION AND MAINTENANCE ------------------ 12
Checking Oil --------------------------------------- 12
Changing Oil --------------------------------------- 13
Checking and cleaning Air Filter --------------14
Adjusting Throttle Cable ------------------------ 15
Adjusting Carburetor ---------------------------- 15
Adjustment of Rear Brake ---------------------- 16
Adjustment of Chain -----------------------------17
Clutch cleaning and maintenance ----------- 18
Vehicle Washing -----------------------------------19
Instruction for Storage -------------------------- 20
Resumption of Service after Storage -------- 21
MAINTENANCE SCHEDULE ----------------------------22
TROUBLE SHOOTING ------------------------------------23
ELECTRICAL SCHEMATIC ------------------------------- 24
safety
Please read this manual and follow all instructions carefully. To emphasize the special
information, the symbol and the words WARNING or CAUTION have some special meanings.
Pay great attention to the messages.
WARNING
Indicates a potential hazard that could result
in death or injury.
CAUTION
Indicates a potential hazard that could result
in vehicle damage.
NOTE: Indicating special information which is to make maintenance easier or instructions
clearer.
WARNING and CAUTION are arranged like this:
WARNING-or-CAUTION
The first part will identify a POTENTIAL HAZARD.
The second part will describe WHAT COULD HAPPEN
if you ignore the WARNING or CAUTION.
The third part will describe HOW TO AVOID THE
HAZARD.
This user’s manual contains important safety and maintenance information. Read it carefully
before riding. Failing to follow the warnings contained in this manual could result in INJURY
or DEATH.
It is important that this manual remain with the vehicle when you transfer it to another user or
owner.
All information, illustrations, photographs and specifications contained in this manual
are based on the latest product information available at the time of publication. Due to
improvements or other changes, there will be some discrepancies in this manual. We reserve
the right to make product changes at any time, without notice and without incurring any
obligation to make the same or similar changes to the vehicle previously built or sold.
safety
SAFE OPERATION
Rules for Safe Operation
·
A pre-operation check must be conducted, before starting the engine, insure safety,
prevent mishaps, and damage to components.
·
It is strongly suggested that all operators take a certified motorcycle rider’s course prior to
operating the vehicle.
·
Full attention is required during driving; paying close attention to the following points to
avoid any injury to you by other motorized vehicles:
·
Do not drive too close to other vehicles.
·
Never carry a passenger. This mini bike is for one operator only
·
Never operate this mini bike at night. Night is defined as the period of time 30 minutes
before sunset to 30 minutes after sunrise.
·
Driving at high speeds is the cause of many accidents; do not drive at a speed that the
actual situation does not permit.
·
This user’s manual contains important safety and maintenance information. Read it
carefully before riding. Failing to follow the warnings contained in this manual could
result in INJURY or DEATH.
·
It is important that this manual remain with the vehicle when you transfer it to another
user or owner.
·
All information, illustrations, photographs and specifications contained in this manual
are based on the latest product information available at the time of publication. Due
to improvements or other changes, there will be some discrepancies in this manual.
We reserve the right to make product changes at any time, without notice and without
incurring any obligation to make the same or similar changes to the vehicle previously
built or sold
·
Always avoid operating this mini bike on paved surfaces, including; sidewalks, paths,
parking lots, driveways, streets, roads, and highways. Never operated this or any Off-Road
Vehicle on a public street, road or highway where motor vehicles are in operation.
safety
SAFETY GEAR
A DOT approved motorcycle helmet is the most important part of you safety gear. A DOT
approved motorcycle helmet can help prevent a serious head injury. Choose a helmet that
fits snugly. Motorcycle dealers can help in selecting a good quality helmet which fits properly.
WARNING
Operating this Mini Bike without wearing an approved DOT motorcycle helmet, eye
protection, and protective clothing could be hazardous.
Operating without an approved DOT motorcycle helmet or eye protection increases
your chances of a severe head injury or death in an accident. Operating without
protective clothing also increases your chances of severe injury in an accident.
Always wear an approved DOT motorcycle helmet which fits properly. Always wear
eye protection (goggles or face shield). You should also wear gloves, boots, long sleeve
shirt or jacket, and long pants.
You should wear eye protection when you ride. If a rock or a branch hits your eyes, you could
be severely injured. Wear goggles or a face shield.
Wear proper clothing when you ride. The proper clothes can protect you from injury. Wear a
good pair of gloves, strong boots that are over the ankle, long pants, and a long sleeve shirt.
CAUTION
Never perform any unauthorized modifications to this vehicle. Only use original
replacement part which can be obtained through Baja Motorsports 888-863-2252.
safety
!••
LOCATION OF LABELS
4
1
3
1
5
2
3
! WARNING
-Moving parts
can crush and
cut.
-Keep hands
clear.
-Do not operate
with guard
removed.
THIS VEHICLE CAN BE HAZARDOUS TO OPERATER IF
DRIVEN CARELESSLY. SERIOUS INJURIES OR DEATH CAN
RESULT IF YOU DO NOT FOLLOW THESE INSTRUCTIONS:
• Read and familiarize yourself with owners manual and all labels
before operating this vehicle.
• Always wear an approved motorcycle helmet, eye gear and
protective clothing.
• Long hair, loose clothing or items worn by the operator must be
covered to prevent them from getting caught in moving parts of
the vehicle or surroundings while riding.
• All fenders and guards must be in place at all times while the
vehicle is in use or serious injury may occure
• Hands, Feet and loose articles must be kept away from the engine,
chain and drive components.
• Check that the throttle and brake controls work freely before
starting the engine.
• Before starting the engine, operator must be seated with
kickstand up.
• NO PASSENGERS
• This vehicle is not made for use on public streets, roads or
highways and is not intended to be used in such places.
• Do not speed on this vehicle, your risk of loosing control increases
if you ride at speeds too fast for specific terrains.
• No person under the age of 16 should operate this vehicle without
adult supervision.
• Do not jump, pop wheelies or try to perform any other stunts as
they can result in serious injury or death.
2
! WARNING
TIRE PRESSURES
• Improper tire pressure can cause loss of
control resulting in serious injury or death.
• Check pressures on all tires only when
tires are cold. 4 psi (27.6 kpa)
• Remove air from tires before demounting.
• Only use replacement tires specified by
manufacture.
! WARNING
4
IMPORTANT
REGULAR SERVICE PROCEDURES
1. Check oil before starting
2. Adjust chain as necessary
3. Clean clutch assembly every 5 hours as needed
4. Check tire pressure.
5. Lubricate chain.
6. For further help, refer to trouble shooting chart.
Do not return to retailer. Call 888-863-BAJA
5
STOP!
DO NOT RETURN THIS
PRODUCT TO STORE.
FOR TECHNICAL SUPPORT
GO!
TO OUR WEBSITE
WWW.bajamotorsports.net
OR CALL TOLL FREE
888-863-2252
FOR THE LATEST PRODUCT INFO
Specifications
MAIN DATA
Description
Data
Description
Data
Overall length
1295mm
(51 inches)
Bore x stroke
52x45
Overall width
476.2mm
(18.75 inches)
PTO shaft rotation
Counter clockwise
Overall height
863.6mm
(34 inches)
Displacement of
cylinder
97cc
Wheelbase
927.1mm
(36.5 inches)
Spark plug
NGK- 6RTF, BM4A,
BMR4A
Dead weight
33.57kg (74 lbs.) Spark plug gap
(0.6mm -0.7mm)
.024 inch - .028 inch
Payload
96.7kg (200lbs)
Ground clearance
127mm (5 inches)
Front wheel
145/70-6
See specified
pressure on tire
Ignition system
Non contact transitor
magneto
Rear wheel
145/70-6
See specified
pressure on tire
Tire Pressure
24 psi Max. to seat bead
4 psi Operating pressure
Brake Type
Disc
Capacity of gasoline 1.4L (.36 gal))
tank
Capacity of oil tank
0.45L (.40 qt)
Drive
Auto clutch
location of parts
Hand brake
Seat Cushion
Spark plug
Front Wheel
Rear Wheel
Oil fill plug
Clutch cover
Oil drain plug
Kick Stand
Drive Chain
Off Button
Throttle handle
Gas Tank
Air Filter
Foot pegs
Brake Caliber
Pull Start Cord
Operation
Left and right hand grip operation
Throttle control grip
Brake Lever
Right Hand Grip
Left Hand Grip
OFF button
Pulling in brake lever located on left hand grip will stop mini
bike.
Applying the hand throttle (moving throttle counter
clockwise ) will cause engine rpms to increase, causing mini
bike to move foreward.
Depressing “OFF” Button will turn off engine.
Engine pull cord operation
Pull Cord
Pulling the pull cord will start the
engine.
Operation
Fuel and fuel valve operation
Fuel filling
The capacity of the fuel tank is 4.2L (.95 gal) . Unscrew the gas cap by turning it counter
clockwise and carefully fill the tank with unleaded gasoline through the opening. DO NOT
MIX GAS AND OIL TOGETHER, THIS IS A 4-STROKE ENGINE. Replace the gas cap by carefully
aligning the threads on the cap and the tank and turning the cap clock wise. Wipe any spilled
fuel from the dirt bike using a cloth and dispose of the cloth properly. DO NOT SMOKE OR
REFUEL THE VEHICLE NEAR OPEN FLAMES OR NEAR HEATING UNITS. ONLY REFUEL THE
VEHICLE IN OPEN AREAS TO REDUCE THE LIKELIHOOD OF THE BUILD UP OF GASOLINE FUMES.
Filler neck
Fuel level
WARNING
Overfilling the fuel tank could be hazardous.
If you overfill the fuel tank, fuel may overflow when it expands. Expanding is due to
heat from engine or sun. Overheated fuel could easily catch fire.
Stop adding fuel when the fuel level reaches the bottom of the filler neck.
Fuel Valve operation
ON: With the handle of the fuel valve to “ON” position, the fuel supply will flow to the
carburetor. In this position the engine is able to start and run.
OFF: With the handle of the fuel valve to “OFF” position, the fuel supply is cut off to the
caburetor. In this position the mini bike will not start and will not run.
Fuel Valve Handle
ON
OFF
inspection before riding
ITEM TO CHECK
Steering
Brakes
Tires
Fuel
Engine stop switch
Engine oil
Throttle
General condition
CONTENT
Smoothness; No restriction of movement; No play or looseness
Proper brake lever free play; enough brake force.
Proper air pressure; Enough tread depth; No cracks, rips, or other
damages Note: Check tire pressure, spec is located on side of tire.
Enough fuel for the intended trip; Fuel hose connected securely; No
damage to fuel tank or cap; Fuel tank cap closed securely
Proper operation
Proper level – Check oil by inspecting Engine Oil Dip Stick. The
engine oil should be between the Minimum and Maximum lines.
Proper free play of throttle lever; smooth response; quick return to
idle position
Bolts and nuts are tight; no rattle from any parts of the engine when
running, no visible evidence of Damage
WARNING
Failing to inspect the Mini Bike before operating could be hazardous. Failing to perform
proper maintenance could also be hazardous.
Failing to inspect and maintain your Mini Bike could increases the chances of an
accident or equipment damage
Always inspect your Mini Bike each time before riding, and make sure it is in a safe operating
condition. Refer to the INSPECTION AND MAINTENANCE section in this manual.
WARNING
Operating this Mini Bike with improper tires, or improper tire air pressure could be hazardous.
If you use improper tires or improper air pressure, you may lose control of the Mini Bike.
This will cause an accident.
Always use the tires with size and type tires specified in this user’s manual. Always
maintain proper tire air pressure as described in the INSPECTION AND MAINTENANCE
section.
Engine starting and stopping
CAUTION
Verify fuel and oil level prior to starting (see page 12)
Starting the engine with low or no oil will damage the engine.
WARNING
Never start the engine in a closed place as the exhausted gas from the vehicle contains
toxic carbon monoxide.
1. Ensure there is fuel in fuel tank and oil in
crank case.
2. Set fuel valve lever to “ON” position
3. Place choke lever in “ON” position
4. Start engine with pull start cord.
5. Allow engine to idle until engine is warm
6. Move carburetor choke lever toward “OFF” position when engine has sufficiently warmed
up. Note: Engine may run ideally with choke lever placed between “ON” position and
“OFF” Position.
Choke Lever
OFF
ON
OFF
Fuel valve lever
CAUTION
Unnecessarily increasing RPM’s to a high level while the Mini Bike is warming up is
harmful to the engine.
Procedures for stopping engine:
1. Release throttle twist grip to slow down engine.
2. Depress stop button located on right hand grip. Depress button until engine comes to a complete stop
3. Set fuel valve lever (the fuel tank valve) handle to “OFF” position.
11
ON
inspection and maintenance
CHECKING THE OIL
Check engine oil each time prior to operating mini bike.
The oil level should be between upper and lower lines of oil gauge.
1. Set the Mini Bike on level ground, screw off the oil gage plug, wipe the oil gage rod clean and
then insert the gage plug into the crankcase again to check the oil level. There is no need to
screw the oil gage plug completely in the hole to check the oil.
2. Add lubricating oil up to the edge of the fuel plug.
3. Screw oil gage plug tightly.
CAUTION
Never start the engine when there is
insufficient lubricating oil. Otherwise, it will
cause harm to the engine.
Oil dip stick
Lubricating Oil Recommended
The lubricating oil is an important factor affecting the performance and service life of the engine.
Please refer to the chart for the correct grade of engine oil based on the environmental conditions
in your area. Do not use any other type of oil other than what is recommended in the chart. DO
NOT MIX OIL WITH THE GASOLINE.
.45L (.40qt) Oil
Lubricating oils of different
viscosity shall be employed
in different regions and at
different temperatures.
MACHINE
OIL
20W-40
20W-50
15W-40
15W-50
10W-40
10W-30
TEMP.
°C
-30
-20
-10
0
10
20
30
40
°F
-22
-4
14
32
50
68
86
104
12
inspection and maintenance
Changing the Oil
1. Remove the “Screw Plug” located at the bottom of the engine and let the oil drain into an
approved collection container. DO NOT PERFORM THIS PROCEDURE WHILE THE ENGINE IS
HOT. SERIOUS BURNS COULD RESULT FROM CONTACT WITH HOT OIL.
2. Dispose of the used oil properly. For proper disposal procedures, contact your local oil
recycling center.
3. Clean and replace the “Screw Plug” tighly.
4. Refill the engine with the proper amount of oil and recheck the amount of oil in the
engine by using the oil gauge plug.
Screw plug for oil draining
Check-up of Spark Plug
1. Remove the cap of spark plug and screw off the spark
plug using the plug wrench.
2. Clean the spark plug all around or replace it if it is
corroded or there is too much deposit on it.
3. Regulate the gap of the spark plug to .7mm - .79mm
(.028”-.031”).
3. The spark plug of the designated type should be used.
The applicable type of spark plug:
Autolite-255, AC-CS45,
Champion-CJ11,NGK-BM6A,
Bosch-WS8E
13
.7mm - .79mm
(.028” - .031”)
inspection and maintenance
Checking & Cleaning the Air Filter
1.
2.
3.
4.
Locate Air Filter Box at rear of engine
Remove air filter cover by unscrewing phillips head screw
Remove foam Air filter element.
Tap Air filter element gently to remove most of the dust and
dirt.
5. Wash foam element per instructions below then allow to
dry thouroghly.
6. Reinstall foam air filter element.
7. Reinstall air filter cover
Air Filter box
Phillips head
screw
Wash with mild soap
and water
Foam Air filter
element
Rinse with fresh water then
queeze out excess.
CAUTION
The air filter element must be intact or the engine will suck in dust and dirt, resulting in a
shorter service life of the engine.
Water should be prevented from entering into the filter when washing the vehicle.
The filter element shall be cleaned gently without twisting to prevent it from cracking.
Never wash it with gasoline or any acid, alkaline or organic volatile oil to avoid its aging,
which will result in reducing the effect of the air filter oil to catch particles before they
enter the engine. Replace the filter element with a new one if it is broken or cracked.
14
inspection and maintenance
Adjusting the Throttle Cable
Make sure the throttle cable is adjusted properly. To adjust throttle cable, rotate adjustment
nut located at the hand throttle.
Check if the throttle twist grip has the required free operating movement.
The required free operating movement: 2-6mm (.078 -.24in) . If the grip cannot be moved
freely, turn the adjusting nut to ensure proper operating movement.
After adjustment, start the engine and check for the operating movement again. Repeat the
adjustment if necessary until the desired operating movement is obtained.
Throttle cable adjust nut
Adjusting the Carburetor
Adjusting procedures of idling speed:
1. Support the vehicle by a stand.
2. Adjust the idle speed by the throttle stop screw to 1400 +200 RPM
-150.
CAUTION
Do not try to correct a malfunctioning carburetor by adjusting the idling speed. If the
carburetor is not functioning properly, it should be repaired by a service center.
Adjust idling speed only when the engine is warmed up or 10 minutes after operation.
15
inspection and maintenance
Adjustment of Rear Brake
1. The front brake hand grip should have free operating
movement of 5-7mm (.2-.3in) . Adjust with free play adjustment bolt.
5-7mm free play
(.2-.3in)
2. To make rear brake pad adjustment, turn rear adjusting
bolt clockwise to loosen and counter clockwise to tighten
brake tension.
3. Brake pads should be replaced by a qualified service
technition once brake shoes are worn .
4. Brakes are adjusted by turning in or out the rear brake
adjusting bolt
Rear brake adjusting bolt
16
Free play adjustment
bolt
inspection and maintenance
Adjustment of Chain
1. When chain adjustment is needed, loosen 4 bolts under engine.
2. Move engine forward to tighten chain or backward to loosen chain.
3. Tighten bolts under engine Torque bolts to 25 ft./lbs.
4. Repetitively check tension of chain.
Nut 2
Nut 1
Loosen
Chain
Engine adjusting bolts
Loosen
Chain
Tighten
Chain
Minor chain adjustment
1. When minor chain adjustment is needed, loosen
“Nut 2”. Turn “Nut 1” clockwise to tighten chain or
counterclockwise to loosen chain.
2. When adjustment is accomplished, tighten Nut 2.
19-25mm
3/4 in. - 1 in.
Greasing procedures to the driving chain
1. Shut off the engine
2. Add light amounts of machine oil or chain grease to the driving chain. (Too much machine
oil or chain grease may cause splattering to occur.)
Attention:
The chain should be replaced when the adjusting limit has reached it’s maximum.
17
inspection and maintenance
Clutch cleaning and maintenance
After every 5 hour of use, your clutch will need cleaning and lubrication. If clutch
becomes too dirty or has lack of lubrication, the clutch will have a tendancy to stick. This
will cause the Mini-Bike to want to take off before throttle is applied.
To clean and lubricate clutch, follow the instructions below:
1. Make sure engine is turned off and engine is cool before removing clutch cover.
2. Remove Clutch Cover
3. With compressed air, blow through holes to remove any dust and/or particles.
4. Oil Clutch bearing with a few drops of 30W motor oil Note: Make sure oil does not get
inside clutch itself.
5. Push Mini bike foreward without starting allowing oil to flow through beaing surface.
6. Re-install clutch cover
WARNING
Starting engine with clutch cover removed could be hazardous
Starting engine with clutch cover removed, increases the chance of getting your person
caught in moving components which could result in severe injury.
Never start Mini Bike with clutch cover removed.
Blow out clutch with compressed
air through large holes
Oil Clutch here ONLY
Clutch Cover
inspection and maintenance
Vehicle Washing
Cleaning the vehicle regularly can slow down the color fading of its body and make it easier
to check if there is any damage and any oil leakage.
CAUTION
Washing the Mini Bike with over-pressurized water may cause damage to some of its
components. Therefore, do use a pressure washer to clean the vehicle. The following
parts should be cleaned using low pressure water:
— Wheel hub
— Exhaust pipe
— Fuel tank and lower portion of cushion
— Carburetor
— Head lock and ignition switch
— Meters
1. After pre-wiping, the vehicle should be washed with clean water to remove dirty residues
so as to prevent corrosion. Plastic subassemblies should be cleaned by wiping with a
cloth or foam soaked in neutral detergent solution, followed by washing with clean water.
2. After the cleaned vehicle is air dried, grease the chain and run the engine at idling speed
for a few minutes.
3. Prior to driving, carefully check the braking system repeatedly and repair or adjust it if
necessary.
19
inspection and maintenance
Instructions for Storage
If the vehicle is not going to be used for a long period of time, for example, in winter time,
some steps should be taken to prevent malfunction of and damage to its components
which might be caused by long storage. Before storing the vehicle for a long period , proper
maintenance has to be carried in case maintenance is not completed when the vehicle is put
back into use after storage.
1. Change engine oil.
2. Drain off fuel from the fuel tank and carburetor, spray atomized anti-rust oil onto the
inside wall of the tank and then close the tank. Dispose of any drained fuel properly so as
not to adversely affect the environment.
Carburetor Drain screw
Attention:
If the storage will last for more than one month, fuel in the carburetor must be fully
drained. This will help ensure that the carburetor maintains its normal performance after
the storage.
WARNING
Gasoline is flammable and may cause fire and even an explosion under certain
conditions. Therefore, do not smoke, make a fire or have any fire around while draining
off fuel.
3. Take out the spark plug, pour about 15-20ml (.5 - .68 oz.) of clean engine oil into the
cylinder, step down on the kick lever repetitively several times so as to have machine oil
distributed all over the engine and finally fit the spark plug back on.
4. Wash the vehicle clean, wipe it dry and apply an even coat of wax to the painted surface
and a coat of anti-rust oil on the chrome-plated surfaces.
5. Inflate the tires as required and put the vehicle up on wooden blocks with the two wheels
clearing the ground.
6. Put the vehicle in a shady and cool place free from humidity and direct sunlight and cover
it properly (not with plastic or other painted materials). If there is a garage, store it within.
20
inspection and maintenance
Resumption of Service after Storage
1. Remove the covering and remove the wooden blocks used in storing the vehicle. Change
the engine oil if the vehicle has been out of service for over 4 months.
2. Drain off the remaining atomized anti-rust oil from the fuel tank, followed by filling it with
fresh gasoline therein.
3. Prior to driving, all the required check-ups must be made. It is better to drive it at a low
speed in an open area to test its performance before normal operation.
21
22
X
X
X
Chain tension - Check
*Brakes - Check
* Throttle - check
2. When Mini bike has exceeded the maximum figures specified in the table, maintenance should be still cycled according to the
intervals of time or hours stated herein.
Notes:
1. Maintenance should be conducted more frequently when Mini Bike is driven in dusty areas.
“**” means: This item can only be carried out by an authorized service center in order to ensure safety.
“*” means: This item of maintenance should be carried out at a service center. It may be also done by the user with reference to this
manual provided special tools and authorized spare parts are used. The user must also be capable of completing the procedure.
X
All nuts and bolts - Check for
tightness
X
Fuel Tube - Chcek
X Every
5 hours
operation
X
Fuel Tank and Filter- Clean
Cintrifugal Clutch - Clean and
Lube
X
X
Every Year or
300 hours
** Valve Clearance - Check, Adjust
X
X
X
Every 6
Months or
100 hours
X
X
X
Every 3
Months or
50 hours
Idle Speed - Check, Adjust
X
1st Month or
20 hours
X
X
X
Each Use
Spark plug - Replace
Spark Plug- Check - Adjust
* Carburetor Sediment cup - Clean
* Air Filter- Change
* Air Filter-Clean
Air Filter-Check
* Engine Oil - Change
Engine Oil- Check
Items of Maintenance
MAINTENANCE SCHEDULE
troubleshooting
Engine will not Start
1. Fuel Valve OFF
2. Choke OFF
3. Out of fuel
4. Bad fuel; engine stored
without treating or draining
gasoline, or refuled with bad
gasoline
5. Spark plug faulty, fouled,
or improperly gapped
6. Spark plug wet with fuel
(flooded engine)
7. Fuel filter clogged,
carburetor malfunction,
ignition malfunction, valves
stuck, etc.
Move Fuel valve lever to ON.
Move Choke Lever to ON
Refuel
Drain fuel and carburetor. Refuel with
fresh gasoline
Remove and inspect spark plug. Clean,
gap, or replace
Remove and inspect spark plug. Dry and
reinstall spark plug.
Take the engine to a qualified mechanic.
Replace or repair faulty components as
necessary
Engine Lacks Power
1. Filter element(s) clogged
2. Choke lever may be not
fully open
2. Bad fuel; engine stored
without treating or draining
gasoline, or refueled with
bad gasoline.
3. Fuel filter clogged,
carburetor malfunction,
ignition malfunction , valves
stuck, etc.
Check air filter
Cean or replace.
Check choke lever
Drain fuel tank and carburetor. Refuel with
fresh gasoline.
Take engine to a qualified mechanic.
Replace or repair faulty components as
necessary.
23
Electrical Schematic
Engine Switch
B1
Transistor Magnito
Spark Plug
Ignition Coil
B1
Baja Motorsports, LLC
2801 So. Fair Lane Ste. 101
Tempe, AZ 85282
Tel: 480-222-8280
Toll Free: 888-863-2252