Black & Decker 90528103 User's Manual

UK
Ireland
Australia
New Zealand
2
3
Intended use
Your Black & Decker cordless three-position pivot drill/
screwdriver has been designed for drilling in wood, metal
and plastics as well as for screwdriving purposes. This tool
is intended for consumer use only.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
! instructions. Failure to follow all instructions may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
1. The term "power tool" in all of the warnings listed below
refers to your mains operated (corded) power tool or
battery operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose
control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is
unavoidable, use a Residual Current Device (RCD)
4
protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is
in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch on
invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a fire.
d. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will make sure that the safety of the power tool is
maintained.
Additional power tool safety warnings
!
X
Warning! Additional safety warnings for cordless
drills and impact drills.
Wear ear protectors with impact drills. Exposure to
noise can cause hearing loss.
X
X
X
X
X
X
Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces when
performing an operation where the fastener may
contact hidden wiring or its own cord. Fasteners
contacting a "live" wire may make exposed metal parts
of the power tool "live" and shock the operator.
Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable
and may lead to loss of control.
Before drilling holes or driving screws into walls,
floors or ceilings, check for the location of wiring and
pipes.
This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety. Children should be
supervised to ensure that they do not play with the
appliance.
The intended use is described in this instruction
manual. The use of any accessory or attachment or
performance of any operation with this tool other than
those recommended in this instruction manual may
present a risk of personal injury and/or damage to
property.
Vibration
The declared vibration emission values stated in the
technical data and the declaration of conformity have been
measured in accordance with a standard test method
provided by EN 60745 and may be used for comparing one
tool with another. The declared vibration emission value may
also be used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons
regularly using power tools in employment, an estimation of
vibration exposure should consider, the actual conditions of
use and the way the tool is used, including taking account of
all parts of the operating cycle such as the times when the
tool is switched off and when it is running idle in addition to
the trigger time.
5
Labels on tools
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Additional safety instructions for batteries and chargers
Batteries
X
Never attempt to open for any reason.
X
Do not expose the battery to water.
X
Do not expose the battery to heat.
X
Do not store in locations where the temperature may
exceed 40 °C.
X
Charge only at ambient temperatures between 10 °C
and 40 °C.
X
Charge only using the charger provided with the tool.
X
When disposing of batteries, follow the instructions
given in the section "Protecting the environment".
Chargers
X
Use your Black & Decker charger only to charge the
battery with which it was supplied. Other batteries could
burst, causing personal injury and damage.
X
Never attempt to charge non-rechargeable batteries.
X
Have defective cords replaced immediately.
X
Do not expose the charger to water.
X
Do not open the charger.
X
Do not probe the charger.
The charger is intended for indoor use only.
Read the instruction manual before use.
+40ºC
+10ºC
Charge only at ambient temperatures between
10 °C and 40 °C.
Electrical safety
Your charger is double insulated; therefore no
earth wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
X
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
1.
2.
3.
4.
5.
6.
7.
8.
Quick release collar
Speed selector switch
Torque adjust collar
Pivot lock release button
Battery release buttons (on battery)
Battery
On/off trigger switch
Forward/reverse and lock-off button
Assembly
Fitting and removing the battery (fig. A)
Warning! Make sure that the lock-off button (8) is engaged
to prevent accidental switch actuation before removing or
installing a battery.
X
To fit the battery (6), line it up with the receptacle on the
tool. Slide the battery (6) into the receptacle and push
until the battery (6) snaps into place.
X
To remove the battery (6), push the two release buttons
(5) simultaneously while at the same time pulling the
battery (6) out of the receptacle.
Charging the battery (fig. C)
This battery is shipped in a partially charged state. Charge
the battery before first use using the mains charger (9) for
nine hours.
The battery (6) needs to be charged whenever it fails to
produce sufficient power on jobs that were easily done
before. When charging the battery (6) for the first time, or
after prolonged storage, it will only accept an 80% charge.
After several charge and discharge cycles, the battery (6)
will attain full capacity. The battery (6) may become warm
while charging; this is normal and does not indicate a
problem.
After normal usage the battery (6) will be fully charged in
approximately three to six hours.
To prolong battery life, do not leave the battery on charge for
extended periods of time (over 30 days without use). This
can significantly reduce battery life.
Fitting the battery cap (fig. D)
Warning! Fit the cap (10) to the battery (6) for transportation
and storage.
Use
Pivoting the tool head (fig. B)
The tool can be pivoted to three different positions (fig. B).
X
To avoid being pinched at the points indicated by the
arrows, hold the screwdriver at both ends and use your
6
X
thumb to press the pivot lock release button (4) when
changing positions.
Do not use the screwdriver as a pry bar in any position.
Switching on and off (fig. E)
X
To switch the tool on, press the on/off trigger switch (7).
X
To switch the tool off, release the on/off trigger
switch (7).
A forward/reverse and lock-off button (8) determines the
direction of the tool and also serves as a lock off button.
X
To select forward rotation, release the on/off trigger
switch (7) and move the forward/reverse and lock-off
button (8) to the left, looking forward.
X
To select reverse direction, move the forward/reverse
and lock-off button (8) in the opposite direction.
The centre position of the forward/reverse and lock-off
button (8) locks the tool in the off position. Make sure that the
on/off trigger switch (7) is released before changing the
position of the forward/reverse and lock-off button (8).
Torque control (fig. E)
Your tool is fitted with an adjustable clutch control feature.
When the tool reaches the pre-selected torque setting, the
clutch slips, therefore limiting how tightly a screw is driven.
The motor will continue to run as long as the on/off trigger
switch (7) is pressed.
X
To set the tools torque, rotate the torque adjust collar (3)
clockwise or counter-clockwise as required. The higher
the number, the higher the torque.
High/low speed selector (fig. E)
The 2-speed feature of your drill allows for greater versatility.
X
To select the low speed, high torque setting (position 1),
turn the tool off and allow it to stop. Move the speed
selector switch (2) towards the back.
X
To select the high speed, low torque setting (position 2),
turn the tool off and allow it to stop. Move the speed
selector switch (2) towards the front.
Warning! Do not move the speed selector switch with the
tool switched on.
Accessories (fig. F)
Your screwdriver is supplied with an accessory pack which
comprises the following 1/4” hex accessories:
X
3 x hex shank drill bits (1.5, 2.5 and 4 mm).
X
4 x 25mm screwdriver bits (Ph2, Slot4, Pz1 and Hex
(Allen) 4 mm).
X
2 x 50mm screwdriver bits (Pz2 and Slot6).
X
1 x magnetic holder.
Quick release collar (fig. G)
Note: The collar accepts 1/4" hex accessories only.
To install a drill bit or other accessory, pull the collar (1) back
and insert the bit into the collar until it locks into place.
To remove a drill bit or other accessory, pull the collar (1)
back. Remove the bit and release the collar.
Driving screws
X
When driving screws, the forward/reverse button (8)
should be pushed to the left.
X
Move the forward/reverse button (8) to the right for
removing screws.
Drilling
This tool is not recommended for drilling in masonry.
Use Black & Decker hex shank drill bits only.
X
Use sharp drill bits only.
X
Support and secure the work properly.
X
Run the drill very slowly, using light pressure, until the
hole is started.
X
Apply pressure in a straight line with the bit. Use enough
pressure to keep the bit biting but not so much as to stall
the motor or deflect the bit.
X
Hold the drill firmly with two hands to control its twisting
action.
X
Do not click the trigger of a stalled drill on and off in an
attempt to start it. Damage to the drill can result.
X
Minimize stalling on breakthrough by reducing pressure
and drilling slowly through the last part of the hole.
X
Keep the motor running while pulling the bit out of a
drilled hole. This will help reduce jamming.
X
With variable speed drills there is no need to centre
punch the point to be drilled. Use a slow speed to start
the hole and accelerate by squeezing the trigger harder
when the hole is deep enough to drill without the bit
skipping out. Operate at full speed after starting the bit.
Drilling wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits. These bits should be sharp and
should be pulled out frequently when drilling to clear chips
from the flutes of the drill.
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The
cutting lubricants that work best are sulfurized cutting oil or
lard oil.
Maintenance
Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
7
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
X
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
X
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
X
Regularly open the chuck and tap it to remove any dust
from the interior.
Protecting the environment
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product
available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again. Reuse of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
X
Safely dispose of the old plug.
X
Connect the brown lead to the live terminal in the new
plug.
X
Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have
reached the end of their working life. To take advantage of
this service please return your product to any authorised
repair agent who will collect them on our behalf.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
Batteries
Black & Decker batteries can be recharged many
times. At the end of their useful life, discard batteries
with due care for our environment:
X
X
8
Run the battery down completely, then remove it from
the tool.
NiCd, NiMH and Lithium Ion batteries are recyclable.
Take them to any authorised repair agent or a local
recycling station.
Technical data
Voltage
Output torque (max)
No load speed
Bit holder
Weight
Battery
Charger
Voltage
Approximate charging time
Weight
Vdc
Nm
rpm
mm
kg
type
HP362
3.6
6
0-200, 0-600
6.35
0.48
A36
Vac 230
hr 6
kg 0.24
EC declaration of conformity
HP362
Black & Decker declares that these products conform to:
98/37/EC, EN 60745
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 57.7 dB(A), uncertainty (K) 3 dB(A)
Acoustic power (LWA) 70.7 dB(A), uncertainty (K) 3 dB(A)
Vibration total values (triax vector sum) according to
EN 60745:
Screwdriving without impact (ah)= 0.98 m/s²,
uncertainty (K) = 1.5 m/s²
Drilling into Metal (ah)= 2.52 m/s², uncertainty (K) = 1.5 m/s²
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker
guarantees to replace defective parts, repair products
subjected to fair wear and tear or replace such products to
make sure of the minimum inconvenience to the customer
unless:
X
The product has been used for trade, professional or
hire purposes.
X
The product has been subjected to misuse or neglect.
X
The product has sustained damage through foreign
objects, substances or accidents.
X
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service
staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our aftersales service and contacts are available on the Internet at:
www.2helpU.com
Please visit our website www.blackanddecker.co.uk to
register your new Black & Decker product and to be kept up
to date on new products and special offers. Further
information on the Black & Decker brand and our range of
products is available at www.blackanddecker.co.uk.
The undersigned is responsible for compilation of the
technical file and makes this declaration on behalf of
Black & Decker
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
01-11-2007
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement
is in addition to and in no way prejudices your statutory
rights. The guarantee is valid within the territories of the
Member States of the European Union and the European
Free Trade Area.
9
10
11
$XVWUDOLD
%ODFN'HFNHU$XVWUDOLD3W\/WG
)OHWFKHU5RDG0RRURROEDUN
9LFWRULD
1HZ=HDODQG
%ODFN'HFNHU
7H$SXQJD3ODFH
0W:HOOLQJWRQ
$XFNODQG
8QLWHG.LQJGRP
%ODFN'HFNHU
%DWK5RDG
6ORXJK%HUNVKLUH6/<'
90528103
7HO
)D[
7HO
)D[
7HO
)D[
+HOSOLQH
12/07