TM
SPACEMAKER
8- C UP T H E R MA L
U NDE R T HE C A B I N E T CO F F E E MAKER
Use & Care Manual
SCM2000BD
Should you have any questions or concerns with your new product,
please call our Customer Service Line at
1-800-231-9786 (US and Canada).
Please do not return to the store.
2
PLEASE READ AND SAVE THIS USE AND CARE BOOK.
IMPORTANT SAFEGUARDS.
When using electrical appliances, always follow basic safety precautions to
reduce the risk of fire, electric shock, and/or injury, including the following:
• Do not use this appliance for anything other
than its intended purpose.
• Do not let cord hang over edge of table or
counter.
• Close supervision is necessary when any
appliance is being used by or near children.
• The use of accessory attachments not
recommended by the manufacturer may
result in fire, electrical shock or other injury.
• Always use handles or knobs. Do not touch
hot surfaces.
• Unplug unit when not in use and before
cleaning.
• Allow unit to cool prior to moving
detachable parts or cleaning.
• To disconnect, turn all controls to OFF, then
remove plug from wall outlet.
• Keep lid on the carafe during the brewing
cycle. Scalding may occur if it is removed.
• Do not use outdoors.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
• To reduce the risk of fire or electric shock:
• Do not rest cord on hot surfaces.
• Do not place on or near a hot gas or
electric burner, or in a heated oven.
• Do not mount this unit over or near any
portion of another heating or cooking
appliance.
• Do not place another heating or cooking
appliance beneath this appliance.
• Do not store anything directly on top of
the appliance.
• Do not immerse cord, plugs or
appliance in liquid.
• Do not mount over a sink.
• Do not operate if cord or plug or appliance
have been damaged, or after a malfunction
of any manner. Call the appropriate toll-free
number found in this manual.
SAVE THESE INSTRUCTIONS.
This product is for household use only.
SAFETY FEATURES
GROUNDED PLUG
As a safety feature, this product is equipped
with a grounded plug, which will only fit into a
three-prong outlet. Improper connection of the
grounding conductor may result in the risk of
electric shock. Consult a qualified electrician if
you are unsure whether the outlet is properly
grounded.
ELECTRICAL CORD
1) A short power-supply cord is provided to
reduce the risk resulting from becoming
entangled in or tripping over a longer cord.
2) Extension cords may be utilized if necessary.
Always exercise care with use.
3) If an extension cord is used:
a) The electrical rating of the cord should, at
a minimum, be as great as the electrical
rating of the appliance
b) T
he extension cord should be a
grounding-type 3-wire cord.
c) To minimize risk of being unintentionally
pulled on or tripped over, the cord should
be arranged so that it will not drape over
the counter or tabletop.
TAMPER-RESISTANT SCREW
A tamper-resistant screw secures the outer
cover. To reduce the risk of fire or electric
shock, do not attempt to remove this screw or
the outer cover. There are no user-serviceable
parts inside. Repairs should be completed by
authorized service personnel only.
Note: If the power supply cord is damaged, it
should be replaced by qualified personnel; in
Latin America, by an authorized service center.
3
WELCOME!
Congratulations on your purchase of the Black+Decker SpaceMaker™
8 Cup Thermal Coffeemaker. We have developed this guide to ensure
optimal product performance and your complete satisfaction.
Save this use and care manual and be sure to register your appliance
online at www.prodprotect.com/applica.
CO NTE NTS
Important Safeguards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Getting to Know Your Coffeemaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing your SpaceMaker™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programming Your Coffemaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Auto Brew Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1-4 Cup Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Before Brewing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Brewing Coffee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Care and Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Warranty and Customer Service Information. . . . . . . . . . . . . . . . . . . . . . . . . . 15
SAV E THE SE IN STR UC T I ONS.
4
G E T T I NG TO KN OW YO UR
SPACEMAKER™ 8 CUP THERMAL COFFEEMAKER
7
6
5
1
4
2
3
1.
6. Digital display
Brew basket
2. Sneak-A-Cup™ interrupt feature
7. Control panel
3. Thermal carafe with lid
8. C
ord management hook
(not shown)
4. Illuminated water reservoir with
water-level markings
5. Reservoir lid
9. P
lug receptacle
(not shown)
Product may vary slightly from what is illustrated.
5
M OU NT I NG
SCREWS
SPACERS
WASHERS
You will also need:
• M
ounting Parts
(Part # SDC-MOUNTING KIT)
16 Spacers
4: 1⁄2 "
4: 1⁄4"
4: 3⁄16 "
4: 1⁄16 "
12 Screws
4: 1"
4: 1 3⁄4"
4: 2 1⁄4"
4 Washers
• Tape
• Ruler
• Electric drill with a 1⁄4” drill bit and
a 1⁄32” drill bit
• Screwdriver
• Protective glasses
• A second person
• Mounting Template (in box)
Note: The use of all provided mounting hardware may not be
necessar y in the installation of all Space Maker ™ produc ts .
6
IN STAL L I NG YOUR SPAC E M A K E R™
G E T T I NG STARTE D
• Carefully unpack your coffeemaker, removing all packaging materials,
labels and/or stickers, and the plastic band around the power plug.
• Register your product at www.prodprotect.com/applica
• Remove and save literature.
• Remove mounting hardware and template. Set them safely aside.
• For warranty verification, do not remove cord tag.
Do not attempt to operate appliance until properly installed.
CH OOS E A LO C ATIO N
When choosing your location, consider the following:
• DO make sure to mount within reach of an electrical outlet.
• DO consider your normal work patterns in the kitchen when choosing location.
• DO NOT mount over any heating or cooking appliance such as your range or
oven.
• DO NOT mount over or near a sink.
• DO NOT mount under, in front of or behind any under-cabinet light
fixtures.
Note: If you are mounting multiple SpaceMaker™ appliances, they should
not be mounted flush to one another. Allow at least 1” of space between
appliances and 4” of space if you are installing a toaster oven. This is
necessary for adequate cooling.
Note: This appliance may feature a Save-A-Plug™ outlet receptacle to
connect smaller SpaceMaker™ appliances. Do not use this outlet for any
other purpose!
If you are connecting this appliance to the receptacle of another
SpaceMaker™ appliance such as the toaster oven or coffeemaker, make
sure you can easily unplug the appliance following use.
DE T E R M I NE C AB IN E T TY P E
Important: SpaceMaker™ appliances are only recommended to be installed
on cabinets without a top lip and with a flat bottom. It is not recommended
to install SpaceMaker™ appliances on cabinets with an overhang. See image
below for recommended cabinet types.
FLAT BOTTOM
TOP LIP
7
OVERHANG
STANDARD INSTALLATION FOR FLAT CABINETS ONLY
Important: Always wear protective glasses or goggles to prevent injury
when drilling.
Important: Do not align screw holes on the template directly under the
partition between cabinets, as this will prevent you from installing the
appliance properly. Pay close attention to where drill holes will be set so as
not to damage your cabinets during mounting. Drilling through your cabinet’s
partition may cause damage to cabinets and prevent proper installation.
1.
Clear countertop under installation area to avoid getting dust or
debris on other appliances or items. Open cabinets and remove
contents to make mounting easier.
2.
Clean both the underside and topside of the bottom panel of the
cabinet.
3.
Decide whether you will be drilling from the top down or from the
bottom up.
4.
IF DRILLING FROM THE BOTTOM UP: With cabinet doors open,
place mounting template against the
D
surface of the front edge of your cabinet.
Align the thick line on the template
(labeled “front edge of cabinet”) with the
lower front edge of your cabinet (D).
5.
Fold the balance of the template up
along the underside of your cabinet,
ensuring the “front edge of cabinet” line
remains aligned with the bottom front
cabinet edge.
6.
Make sure the template is smooth and
flush against the cabinet’s underside.
Pull template tight and tape down to
hold in place.
7.
IF DRILLING FROM THE TOP DOWN:
With cabinet doors open, place mounting
template against the surface of the front
edge of your cabinet. Align the thick line
on the template (labeled “front edge of
cabinet”) with the upper front edge of
your cabinet (E).
8.
Fold the balance of the template over
into the inside of your cabinet, ensuring
the “front edge of cabinet” line remains
aligned with the upper front cabinet
edge.
9.
Make sure the template is smooth and
flush against the cabinet’s inside. Pull
template tight and tape down to hold in
place.
8
E
Important: Always ensure you are drilling straight
up or straight down through the marked mounting
holes on the template. Drilling at an angle may
prevent proper installation and may damage
cabinets if the drill bit pierces the partition.
8. Using a 1⁄32” drill bit, drill from the underside
of the cabinet up or the top down, creating
pilot holes through the 4 holes marked on the
template. This will help guide the ¼” drill bit in
the next step. (F)
F
G
9. Switch to a ¼” drill bit and drill straight up or
straight down through the holes that have
just been created. (G)
10. Once holes are drilled, remove tape and
mounting template.
11. Wipe dust and debris off the top side and
the underside of the cabinet surface.
H
12. Place a washer inside the cabinet over each
of the 4 holes you drilled. (H)
11. Determine what size screws to use by placing
a screw through the hole in the cabinet
without the appliance in place. The screw
should be ½” exposed underneath the cabinet
to ensure the appliance is properly attached
to the cabinet. Once you have determined the
screw size, proceed to step 12. (I)
I
Note: Several standard screw lengths are
provided but may not fit all cabinet sizes.
12. Place one of the screws through each of the
washers covering the holes in the cabinet,
from the inside of the cabinet down.
13. Hold appliance up to the screws, aligning
the front of the appliance with the front
edge of the cabinet base. The screws in
the cabinet should align with the mounting
holes in the appliance. (J)
J
Note: It may require two people to ensure the
appliance is held in place while drilling.
14. Screwing from inside the cabinet down
into the appliance holes, use your drill or
screwdriver to tighten the four screws in
place. (K)
Note: Always tighten screws to properly secure
the appliance to the cabinet and to ensure
the appliance does not move or shake during
operation.
9
K
15. Pull out cord from cord storage behind the
appliance and plug into a standard electrical
outlet. Extra cord can be fed back into
storage or hung over cord management
hook behind the appliance. (L)
L
Note: If you are connecting this appliance to the
receptacle of another SpaceMaker™ appliance such
as the toaster oven or coffeemaker, make sure you
can easily unplug the appliance following use.
16. Your SpaceMaker™ appliance is now ready for use!
PR OGR A M M I NG YO UR CO F F E E MAKER
SETTING THE DIGITAL CLOCK
1.
Plug your coffeemaker into a standard electrical outlet.
2.
The entire digital clock will flash “12:00” to indicate that the time has
not yet been set.
3.
Press the HOUR and MIN (minute) buttons until the correct time
appears on the display.
*A “PM” symbol will appear to indicate afternoon time settings. This
symbol will not appear for AM settings.
4.
Your clock is now set.
SETTING THE AUTO BREW DELAY
1.
Ensure the digital clock has been set (see “SETTING THE DIGITAL
CLOCK” section for assistance).
2.
Press the PROG (program) button. The display will flash “12:00.”
3.
Press the HOUR and MIN buttons until they indicate the time you
would like automatic brewing to begin.
*A “PM” symbol will appear in the upper right hand corner of the
digital display to indicate afternoon time settings. This symbol will
not appear for AM settings.
4.
The Auto Brew display will flash for a few moments before switching
back to the digital clock.
TIP: After programming, press the PROG button to check the preset Auto
Brew time.
10
ACTIVATING THE AUTO BREW DELAY
1.
Ensure the Auto Brew delay time has been set
(see “SETTING THE AUTO BREW DELAY” section for assistance).
2
Press the AUTO button once. The word “AUTO” will appear and the
LED light above the AUTO button will illuminate.
3. When Auto Brew is activated, be sure to have both coffee
grounds and water in your coffeemaker. When the time of day
and programmed Auto Brew time match, your coffeemaker will
automatically brew a fresh pot of coffee.
4. To deactivate Auto Brew, press the AUTO button again. The AUTO
icon and light will disappear will turn off.
Note: If the unit is unplugged or power is interrupted, the digital clock
and Auto Brew settings will need to be reprogrammed.
THE 1-4 CUP SETTING
Simply push the “1-4 Cup” button and an icon will appear on the LCD
display indicating the setting has been activated.
Your coffeemaker will optimize water temperature and speed, to
maintain bold coffee flavor when brewing 1-4 cups of coffee.
BE FO R E B R E WIN G
•
lean all removable parts of your coffeemaker in warm, soapy water.
C
Rinse and dry these parts prior to placing them back into your
coffeemaker.
•
o remove any remaining dust or residue from the manufacturing
T
process, run two full brewing cycles using only water, no coffee.
•
Make sure your coffeemaker is plugged in. The water reservoir
light will be illuminated and remain on as long as the appliance
is plugged in.
•
Remove the integrated water reservoir and fill with fresh, cool
water. Replace water reservoir into coffeemaker. Be sure it snaps
into place securely.
•
Remove the brew basket and place an empty 8-12 cup basket
style paper filter into it. Do not add coffee grounds. Replace
brew basket. Be sure it snaps into place securely.
•
Place brew-through lid on empty carafe. Coffee may overflow if
brew-through lid is not properly aligned.
•
Insert carafe securely along slots of carafe holder. Ensure carafe
is fully inserted.
•
Press the On/Off button to start the brew cycle.
•
Once the brew cycle is finished, discard the water from the
carafe as well as the paper filter from brew basket.
•
Turn off appliance, unplug and allow unit to cool for 15 minutes
before repeating.
11
BR E W I NG COF F E E
1.
Fill water reservoir with desired amount of fresh, cool water using
water markings on water reservoir window. Do not exceed the
maximum marked level. Replace water reservoir into coffeemaker. Be
sure it snaps into place securely.
2. Remove the brew basket and place an empty 8-12 cup basket style
paper filter into it.
3. Add ground coffee into the filter (we suggest 1 tablespoon per cup).
4. Replace brew basket. Be sure it snaps into place securely.
5. Place brew-through lid on empty carafe. Coffee may overflow if
brew-through lid is not properly aligned.
6. Insert carafe securely along slots of carafe holder. Make sure carafe is
fully inserted.
7. For immediate brewing press the On/Off button. To use the Auto
Brew Delay Start, Brew Strength Selector or 1-4 Cup setting, follow
the instructions in the “PROGRAMMING YOUR COFFEEMAKER”
section of this guide.
8. While brewing, the Sneak-A-Cup™ feature stops coffee flow out of
the unit, allowing you to pour a cup of coffee before the brew cycle
finishes. Always return the carafe on to the carafe plate within 20
seconds to prevent coffee overflow.
9. Your coffeemaker will turn off when the brew cycle is complete. The
thermal carafe will keep brewed coffee hot for about 2 hours.
10. The freshness indicator LED will turn on and remain on for
20 minutes.
11. When the coffee grounds are cool, carefully remove and dispose
them as well as the used filter.
12. Clean your coffeemaker according to the instruction in the
“CARE AND CLEANING” section.
12
C AR E A N D C L EA N IN G
CLEANING:
Follow the directions below to clean your coffeemaker after each use.
1. Make sure your coffeemaker is unplugged and cool.
2. Open your coffeemaker’s filter basket lid and remove the brew basket.
3. If remaining, throw away the used paper filter and coffee grounds.
4. Wash the brew basket and carafe by hand in warm, soapy water or on
the top rack of your dishwasher (ensure carafe is applicable below).
5. Wipe the outside of the coffeemaker, power cord and carafe plate with a
soft, damp cloth.
6. To clean the inside of the filter basket lid, open the filter basket lid and
wipe any surfaces with a damp cloth.
Note: D
o not use abrasive cleansers or scouring pads on this product.
Never immerse the coffeemaker in water.
COFFEEMAKER PART
CLEANING INSTRUCTIONS
Housing
Carafe Plate
Power Cord
Wipe with a soft, damp cloth.
Carafe Lid
Brew Basket
Glass Carafes
Wash by hand in warm soapy water,
or in the dishwasher (top rack only).
Thermal Carafes
Wash by hand in warm soapy water
DESCALING WITH VINEGAR:
To remove mineral build up that can affect the taste and quality of your
coffee, descaling your coffeemaker with vinegar every 3 to 6 months is
recommended. To descale, follow the instructions below:
1. Open the filter basket lid and fill the water reservoir approximately half
way with white vinegar. Fill the remaining half of the water reservoir
with cool water.
2. Place a paper filter into the brew basket, close the lid and check to
ensure the empty carafe is placed on the carafe plate.
3. Push the POWER button to start the brewing cycle.
4. After approximately half the cleaning mixture has brewed into the
carafe, press the POWER button again to turn OFF the unit.
5. Let soak for a minimum of 15 minutes and then press POWER again to
turn the coffeemaker on.
6. Brew the remaining cleaning mixture into the carafe.
7. Following ‘Cleaning’ instructions from above.
8. Run a full brew cycle using only water. You may want to repeat this step
more than once.
9. Wash the brew basket and carafe as instructed above.
13
T RO U B L ES HO OTIN G
PROBLEM
POSSIBLE CAUSE
SOLUTION
Coffeemaker
does not turn on.
Coffeemaker is
not plugged in.
Check to be sure appliance is
plugged into a working outlet
and the ON/OFF (I/O) button
has been pressed.
Coffeemaker is
leaking.
Water reservoir
may be overfilled.
Make sure the water reservoir
has not been filled beyond the
MAX fill line.
Brewing takes
too long.
The coffeemaker
may need to be
descaled.
Follow procedure in
Descaling With Vinegar
section of this guide.
Coffee is not
brewing.
Water reservoir
might be empty.
Make sure water reservoir
has sufficient water to brew
desired number of cups of
coffee.
The coffeemaker
brews clear
water.
There may be no
coffee grounds in
the brew basket.
Add sufficient amount of
coffee grounds to filter lined
brew basket.
Brew basket
overflows.
Carafe may
be improperly
placed.
Remove carafe and insert
back into place. Ensure carafe
is placed correctly on and
is centered under the filter
basket.
Grounds in the
brewed coffee.
The filter and/or
the brew basket
are not properly
placed.
Reinsert paper filter into brew
basket and insert basket
properly into brew basket.
14
NE E D H E L P ?
For support or any questions regarding your appliance, call the appropriate
800 number listed within this section. Please DO NOT return the product
to the place of purchase. Also, please DO NOT mail product back to
manufacturer, nor bring it to a service center. You may also want to consult
our Product Protection Center at www.prodprotect.com/applica .
Two-Year Limited Warranty
(Applies only in the United States and Canada)
What does my warranty cover?
•Your warranty covers any defect in material or workmanship provided; however, the
liability of Spectrum Brands Inc. will not exceed the purchase price of product.
How long is the warranty period?
•Your warranty extends two years from the date of original purchase with proof of
purchase.
What support does my warranty provide?
•Your warranty provides you with a reasonably similar replacement product that is
either new or factory refurbished.
How do you get support?
•Save your receipt as proof of date of sale.
•Visit the online service website at www.prodprotect.com/applica, or call toll-free
1-800-231-9786, for general warranty service.
•If you need parts or accessories, please call 1-800-738-0245.
What does my warranty not cover?
•Damage from commercial use
•Damage from misuse, abuse or neglect
•Products that have been modified in any way
•Products used or serviced outside the country of purchase
•Glass parts and other accessory items that are packed with the unit
•Shipping and handling costs associated with the replacement of the unit
•Consequential or incidental damages (Please note, however, that some states do
not allow the exclusion or limitation of consequential or incidental damages, so
this limitation may not apply to you.)
How does state law affect my warranty?
•This warranty gives you specific legal rights. You may also have other rights that
vary from state to state or province to province.
15
TM
© 2014 The Black & Decker Corporation
and Spectrum Brands, Inc.,
Middleton, WI 53562
Made in People’s Republic of China
BLACK+DECKER and the BLACK+DECKER logo are trademarks of
The Black & Decker Corporation and are used under license. All rights reserved.
16
T22-5001378
2014/9/16/118