Blade ICE 831.48853 User's Manual

Model No. 831.488530
User's Manual
Setup
1, Firmly press the thumb
tab and pivot the
upright up until it locks in a nearly vertical position.
2.
Insert the handles into the stem until the
lock pins are visible in the holes in the
stem.
3. Open
the quick-release
lever. Depress the
lock pin on the stem and slide the stem
up until the lock pin is visible in one of
the three holes in the upright. When the
stem is at the desired height, close the
quick-release lever so that it is snug
against the upright. If the quick-release is
not snug, see ADJUSTING THE
QUICK-RELEASE
on the back of this
user's manual.
Before using the scooter, make sure that
the scooter is set up as descried
and that
all parts are securely tightened.
The decal shown at the right has been
placed on the scooter. If the decal is missing, or if it is not legible, please call our
Customer Service Department toll-free at
1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time, to
order a free replacement decal. Apply the
replacement
decal in the location shown.
t
Toprevent
serious Injury:
•Read, understand
and follow all warnlngs and instructions on the unit
and in the manual.
Carry
•Always wear protective equipment
Including helmet,
kneepads,
wast
guards, and elbow
pads.
• Keep away from
cars, stnlets or
areas that enter
vehicle traffic
routes.
.Neverddewhen
towedbehind blcycles, motorcycles, orvehlcles.
Right Side
Rear Brake
•Do not dde at
night or In poor
visibility.
Left Side
Storage
1. Open
thequick-release
lever. Depress the
lock pin on the stem and slide the stem
down into the upright. Close the quickrelease lever.
2.
Upright
Depress the lock pins and remove the
handles from the stem. Press the handles
into the storage clip on the upright.
3. Pull
the thumb tab and pivot the upright
down until it locks in the horizontal position.
Carry Strap notshown.
Clip
Part List/Exploded Drawing
Model No. 831.488530
No. Qt_
Desc_pfion
R0700A
1
2
3
1
1
1
Deck
Head Tube
Fork
4
5
6
7
1
1
2
2
Upright
Stem
Handle
Foam Pad
8
9
10
2
3
1
Handle Cap
Lock Pin
Handle Cord
11
12
13
14
15
16
17
18
19
20
21
1
1
1
1
2
2
2
1
1
2
2
Quick Release
Upright Clamp w/Ring
Bearing Nut
Bearing Cap
Bearing
Bearing Race
Bushing
Pivot Union Bolt Set
Front Union Bolt Set
Rear Union Bolt Set
Wheel
22
23
24
2
1
1
Rear Wheel Spacer
Brake Spring
Brake
25
26
27
28
1
1
2
1
Head Tube Spring
Storage Clip
Front Wheel Spacer
Lock Pin
29
*
*
1
1
1
Strap Clamp w/Ring
Carry Strap
User's Manual
26
16.
17
18
2O
19
*The user's manual and carry strap am not shown
24
21
Note: Specifications are subject to change without
notice.
Ordering Replacement Parts
To order replacement parts, call toll-flee 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time
(excluding holidays). When ordering parts, please mention the model number (831.488530) and the number and description of the parts needed.
Adjusting The Quick-Release
If the quick-release doesn't hold the stem snug in place,
you will need to adjust it.
Open the quick-release lever. Turn the adjustment nut
clockwise one half turn while keeping the lever from turning. Close the lever. Repeat this procedure until the stem is
held snug in place.
If the quick-release is too snug to close, you will need to
adjust it.
Quick
Close
Release
Adjustment
Nut
While the quick-release lever is open, turn the adjustment
nut counterclockwise
one quarter turn while keeping the
lever from turning. Close the lever. Repeat this procedure
until the stem is held snug in place and the quick-release is
closed.
Part No. 167661 R0700A Printed in China
© 2000 ICON Health & Fitness, Inc.