Brother HL-700 Series User's Manual

Please read this manual thoroughly before using the printer.
Brother Laser Printer
HL-700 Series
User’s Guide
Keep this manual in a convenient place for quick and easy reference at all times.
I
Shipment of the Printer
If for any reason you must ship your Printer, carefully package the
Printer to avoid any damage during transit. It is recommended that you
save and use the original packaging. The Printer should also be
adequately insured with the carrier.
Warning
When shipping the Printer, the DRUM UNIT assembly including the
TONER CARTRIDGE must be removed from the Printer and placed in
the plastic bag. Failure to remove and place it in the plastic bag
during shipping will cause severe damage to the Printer and will
VOID THE WARRANTY.
1 Remove the drum unit.
3 Re-pack the printer.
See “REPACKING THE PRINTER”
in Chapter 5.
II
2 Place it in the plastic bag and seal the
bag completely.
Laser Printer HL-700 Series User’s Guide
(For USA & CANADA Only)
For technical and operational assistance, please call:
In USA
In CANADA
1-800-276-7746
714-859-9700 Ext. 329
1-800-853-6660
514-685-6464
(outside California)
(within California)
(within Montreal)
If you have comments or suggestions, please write us at:
In USA
In CANADA
Printer Customer Support
Brother International Corporation
15 Musick
Irvine, CA 92718
Brother International Corporation (Canada), Ltd.
- Marketing Dept.
1, rue Hôtel de Ville
Dollard-des-Ormeaux, PQ, Canada H9B 3H6
BBS
For downloading drivers from our Bulletin Board Service, call:
In USA
1-714-859-2610
In CANADA
1-514-685-2040
Please log on to our BBS with your first name, last name and a four digit number for
your password. Our BBS supports modem speeds up to 14,400, 8 bits no parity, 1
stop bit.
Fax-Back System (For USA only)
Brother Customer Service has installed an easy to use Fax-Back System so you can
get instant answers to common technical questions and product information for all
Brother products. This is available 24 hours a day, 7 days a week. You can use the
system to send the information to any fax machine, not just the one you are calling
from.
Please call 1-800-521-2846 and follow the voice prompts to receive faxed
instructions on how to use the system and your index of Fax-Back subjects.
DEALERS/SERVICE CENTERS (USA only)
For the name of an authorized dealer or service center, call 1-800-284-4357.
SERVICE CENTERS (Canada only)
For service center addresses in Canada, call 1-800-853-6660
INTERNET ADDRESS
For technical questions and downloading drivers: http://www.brother.com
i
USER’S GUIDE
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Apple, the Apple Logo, and Macintosh are trademarks, registered in the
United States and other countries, and TrueType is a trademark of Apple
Computer, Inc.
Epson is a registered trademark and FX-80 and FX-850 are trademarks of
Seiko Epson Corporation.
Hewlett Packard is a registered trademark and HP LaserJet II, IIP, and IID
are trademarks of Hewlett-Packard Company.
IBM, IBM PC, and Proprinter are registered trademarks of International
Business Machines Corporation.
Microsoft and MS-DOS are registered trademarks of Microsoft
Corporation. Windows is a registered trademark of Microsoft Corporation
in the U.S. and other countries.
All other brand and product names mentioned in this User’s Guide are
registered trademarks of their respective companies.
Compilation and Publication Notice
Under the supervision of Brother Industries Ltd., this manual has been
compiled and published, covering the latest product’s descriptions and
specifications.
The contents of this manual and the specifications of this product are
subject to change without notice.
Brother reserves the right to make changes without notice in the
specifications and materials contained herein and shall not be responsible
for any damages (including consequential) caused by reliance on the
materials presented, including but not limited to typographical and other
errors relating to the publication.
©1997 Brother Industries Ltd.
ii
Definitions of Warnings, Cautions, and Notes
The following conventions are used in this User’s Guide:
Warning
Indicates warnings that must be observed to prevent possible
personal injury.
!
Caution
Indicates cautions that must be observed to use the printer properly or
prevent damage to the printer.
✒ Note
Indicates notes and useful tips to remember when using the printer.
To Use the Printer Safely
Warning
After you have just used the printer, some internal parts of the
printer are extremely hot. When you open the top cover of the
printer, never touch the shaded parts shown in the following
illustration.
High Temperature
Inside the Printer
Warning
There are high voltage electrodes inside the printer. Before cleaning
the printer, make sure to turn off the power switch and unplug the
power cord from the power outlet.
Turning off the Switch and Unplugging the Printer
iii
USER’S GUIDE
TABLE OF CONTENTS
REGULATIONS..................................................................................................................vi
CHAPTER 1 INTRODUCTION.....................................................................................1–1
ABOUT THE GUIDEBOOKS...........................................................................................1–1
Finding Out How to Use the Printer...............................................................................1–1
ABOUT YOUR PRINTER.................................................................................................1–2
Printer Overview ............................................................................................................1–2
System Requirements .....................................................................................................1–3
Features ..........................................................................................................................1–3
OPERATING AND STORAGE ENVIRONMENT ...........................................................1–6
Power Supply .................................................................................................................1–6
Environment ...................................................................................................................1–6
CHAPTER 2 PAPER HANDLING.................................................................................2–1
PAPER SPECIFICATIONS................................................................................................2–1
MULTI-PURPOSE SHEET FEEDER................................................................................2–4
Loading Paper into the Feeder........................................................................................2–5
Two Side Printing (Manual Duplexing) .........................................................................2–7
MANUAL FEED SLOT.....................................................................................................2–8
OUTPUT TRAY AND PAPER SUPPORT WIRE ...........................................................2–10
CHAPTER 3 CONTROL PANEL ..................................................................................3–1
LAMPS AND SWITCH .....................................................................................................3–1
Ready (Paper) Lamp.......................................................................................................3–1
Data (Toner) Lamp .........................................................................................................3–2
Drum Lamp ....................................................................................................................3–2
Alarm Lamp ...................................................................................................................3–2
Switch.............................................................................................................................3–3
Other Control Features ...................................................................................................3–3
Sleep Mode.................................................................................................................3–3
Test Print Mode ..........................................................................................................3–4
CHAPTER 4 OPTIONS...................................................................................................4–1
SERIAL INTERFACE BOARD RS100M (For HL-730 / 730Plus series Only) ..................4–1
Selecting the RS-422A (Apple) or RS-232C (IBM) Serial Interface .............................4–1
Setting the Serial Interface Parameters...........................................................................4–2
Connecting the Serial Interface Cable ............................................................................4–4
MEMORY BOARD ...........................................................................................................4–6
iv
TABLE OF CONTENTS
CHAPTER 5 MAINTENANCE ......................................................................................5–1
REPLACING THE TONER CARTRIDGE .......................................................................5–1
REPLACING THE DRUM UNIT......................................................................................5–6
ADJUSTING THE PRINT DENSITY.............................................................................5–10
CLEANING THE PRINTER ...........................................................................................5–11
Cleaning the Printer Exterior........................................................................................5–11
Cleaning the Printer Interior and Drum Unit................................................................5–12
RE-PACKING THE PRINTER ........................................................................................5–15
CHAPTER 6 TROUBLESHOOTING............................................................................6–1
ALARM INDICATIONS AT A GLANCE .........................................................................6–1
Operator Calls ................................................................................................................6–1
Service Calls...................................................................................................................6–4
PAPER JAMS.....................................................................................................................6–5
Q & A .................................................................................................................................6–8
Setting Up the Printer Hardware ....................................................................................6–8
Setting Up the Printer for Windows ...............................................................................6–8
Setting Up the Printer for DOS (For HL-730 / 730Plus series Only).............................6–9
Setting Up the Printer for Apple Macintosh Computers
(For HL-730 / 730Plus series Only) .............................................................................6–10
Paper Handling .............................................................................................................6–10
Printing .........................................................................................................................6–11
Print Quality .................................................................................................................6–12
APPENDIX A ..................................................................................................................A–1
PRINTER SPECIFICATIONS ..........................................................................................A–1
Printing ..........................................................................................................................A–1
Functions .......................................................................................................................A–2
Electrical and Mechanical .............................................................................................A–3
PARALLEL INTERFACE SPECIFICATIONS ................................................................A–4
RESIDENT FONTS (For HL-730 / 730Plus series Only) ................................................A–6
SYMBOL SETS/CHARACTER SETS (For HL-730 / 730Plus series Only) ...................A–7
INDEX ...................................................................................................................... Index–1
v
USER’S GUIDE
REGULATIONS
Federal Communications Commission Compliance Notice (For USA Only)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
❏ Reorient or relocate the receiving antenna.
❏ Increase the separation between the equipment and receiver.
❏ Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
❏ Consult the dealer or an experienced radio/TV technician for help.
Important
A shielded interface cable should be used in order to ensure compliance with the limits for a
Class B digital device.
Changes or modifications not expressly approved by Brother Industries, Ltd. could void the
user’s authority to operate the equipment.
Industry Canada Compliance Statement (For Canada Only)
This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur la matériel brouilleur du Canada.
International Energy Star Compliance Statement
The purpose of the International Energy Star Program is to promote the
development and popularization of energy-efficient office equipments, which
includes computers, monitors, printers, facsimile receivers and copy machines
world-wide.
As an International Energy Star partner, Brother Industries, Ltd. has decided that
this product meets the guideline of the program.
vi
REGULATIONS
Radio Interference (220-240 V Model Only)
This printer complies with EN55022(CISPR Publication 22)/Class B.
Before this product is used, ensure that you use a double-shielded interface cable with
twisted-pair conductors and that it is marked “IEEE 1284 compliant”. The cable must
not exceed 1.8 metres in length.
Laser Safety (For 110–120 V Model Only)
This printer is certified as a Class I laser product under the U.S. Department of Health and
Human Services (DHHS) Radiation Performance Standard according to the Radiation Control
for Health and Safety Act of 1968. This means that the printer does not produce hazardous
laser radiation.
Since radiation emitted inside the printer is completely confined within protective housings
and external covers, the laser beam cannot escape from the machine during any phase of user
operation.
FDA Regulations (For 110-120 V Model Only)
U.S. Food and Drug Administration (FDA) has implemented regulations for laser products
manufactured on and after August 2, 1976. Compliance is mandatory for products marketed
in the United States. One of the following labels on the back of the printer indicates
compliance with the FDA regulations and must be attached to laser products marketed in the
United States.
MANUFACTURED:
Brother Corporation (Asia) Ltd. Brother Buji Nan Ling Factory
Gold Garden Ind., Nan Ling Village, Buji, Rong Gang, Shenzhen, CHINA
This product complies with FDA radiation performance standards, 21 CFR Subchapter J
MANUFACTURED:
BROTHER INDUSTRIES (USA) INC.
2950 Brother Blvd., Bartlett, TN 38133, U.S.A.
This product complies with FDA radiation performance standards, 21 CFR Subchapter J
MANUFACTURED:
BROTHER INDUSTRIES LTD.
15-1 Naeshiro-cho Mizuho-ku Nagoya, 467 Japan
This product complies with FDA radiation performance standards, 21 CFR Subchapter J
Caution
Use of controls, adjustments or performance of procedures other than those specified in this
manual may result in hazardous radiation exposure.
vii
USER’S GUIDE
Declaration of Conformity (For Europe)
We, Brother International Europe Ltd.,
Brother House 1 Tame Street, Guide Bridge, Audenshaw, Manchester M34 5JE, UK.
declare that this product is in conformity with the following normative documents.
Safety:
EMC:
EN 60950,
EN 55022 Class B,
EN 60825
EN 50082-1
following the provisions of the Low Voltage Directive 73/23/EEC and the Electromagnetic
Compatibility Directive 89/336/EEC (as amended by 91/263/EEC and 92/31/EEC).
Issued by:
Brother International Europe Ltd.
European Technical Services Division
IEC 825 Specification (For 220–240 V Model Only)
This printer is a Class 1 laser product as defined in IEC 825 specifications. The label shown
below is attached in countries where required.
CLASS 1LASER PRODUCT
APPAREIL Å LASER DE CLASSE 1
LASER KLASSE 1 PRODUKT
This printer has a Class 3B Laser Diode which emits invisible laser radiation in the Scanner
Unit. The Scanner Unit should not be opened under any circumstances.
Caution
Use of controls, adjustments or performance of procedures other than those specified in this
manual may result in hazardous radiation exposure.
The following caution label is attached near the scanner unit.
viii
CAUTION
ADVARSEL
VARNING
VARO!
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.
AVOID DIRECT EXPOSURE TO BEAM. CLASS 3B LASER PRODUCT.
ADVARSEL
ATTENTION
VORSICHT
USYNLIG LASERSTRÅLING.UNNGÅ DIREKTE KONTAKT MED LASERENHETEN
NÅR TOPPDEKSELET ER ÅPENT. KLASSE 3B LASERPRODUKT.
ATENCIÓN
RADIACIÓN LASER INVISIBLE CUANDO SE ABRE
LA TAPA Y EL INTERRUPTOR INTERNO ESTÁ
ATASCADO. EVITE LA EXPOSICIÓN DIRECTA
DE LOS OJOS. PRODUCTO LASER CLASE 3B.
USYNLIG LASER STRÅLING NÅR KABINETLÅGET STÅR ÅBENT.
UNGDÅ DIREKTE UDSÆTTELSE FOR STRÅLING. KLASSE 3B LASER.
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR
ÄR URKOPPLADE. STRÅLEN ÄR FARLIG. KLASS 3B LASER APPARAT.
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN. LUOKAN
3B LASERLAITE.
RADIATIONS LASER INVISIBLES QUANDOUVERT ET VERROUILLAGE ENLEVE.
EVITER EXPOSITIONS DIRECTES AU FAISCEAU. PRODUIT LASER CLASSE 3B.
UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG
GEÖFFENT UND SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
SICHERHEITSKLASSE 3B.
REGULATIONS
For Finland and Sweden
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla tavalla saattaa
altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
Varning – Om apparaten används på annat sätt än i denna Bruksanvisning specificerats, kan
användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
IMPORTANT - For Your Safety
To ensure safe operation the three-pin electrical plug supplied must be inserted only into a
standard three-pin power point which is properly grounded through normal household wiring.
Extension cords used with the equipment must be three-pin plug type and correctly wired to
provide proper grounding. Incorrectly wired extension cords may cause personal injury and
equipment damage.
The fact that the equipment operates satisfactorily does not imply that the power is grounded
and that the installation is completely safe. For your safety, if in any doubt about the effective
grounding of the power, consult a qualified electrician.
Disconnect device
This printer must be installed near a power outlet, which is easily accessible. In case of
emergencies, you must disconnect the power cord from the power outlet in order to shut off
power completely.
Geräuschemission / Acoustic Noise Emission (For Germany Only)
Lpa < 70 dB (A) DIN 45635-19-01-KL2
ix
USER’S GUIDE
IMPORTANT - Wiring Information (For U.K. only)
If the power cord supplied with this printer is not suitable for your electrical outlet, remove
the plug from the mains cord and fit an appropriate three pin plug. If the replacement plug is
intended to take a fuse then fit the same fuse as the original.
If a moulded plug is severed from the power cord then it should be destroyed because a plug
with cut wires is dangerous if plugged into a live socket outlet. Do not leave it where a child
might find it.
In the event of replacing the plug fuse, fit a fuse approved by ASTA to BS1362 with the same
rating as the original fuse.
Always replace the fuse cover. Never use a plug with the cover omitted.
WARNING - THIS PRINTER MUST BE PROPERLY EARTHED.
The wires in the mains cord are coloured in accordance with the following code:
Green and yellow:
Blue:
Brown:
Ground
Neutral
Live
The colours of the wiring in the power lead of this printer may not correspond with the
markings which identify the terminals in your plug. If you need to fit a different plug,
proceed as follows.
Remove a length of the cord outer sheath, taking care not to damage the coloured insulation
of the wires inside.
Cut each of the three wires to the appropriate length. If the construction of the plug permits,
leave the green and yellow wire longer than the others so that, in the event that the cord is
pulled out of the plug, the green and yellow wire will be the last to disconnect.
Remove a short section of the coloured insulation to expose the wires.
The wire which is coloured green and yellow must be connected to the terminal in the plug
which is marked with the letter “E” or by the earth symbol or coloured green or green and
yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the
letter “N” or coloured black or blue.
The wire which is coloured brown must be connected to the terminal which is marked with
the letter “L” or coloured red or brown.
The outer sheath of the cord must be secured inside the plug. The coloured wires should not
hang out of the plug.
x
CHAPTER 1 INTRODUCTION
CHAPTER 1
INTRODUCTION
ABOUT THE GUIDEBOOKS
Finding Out How to Use the Printer
You have two guidebooks for this printer. Read each guidebook in the
following order:
1. Read the Quick Setup Guide to set up your printer and to ensure proper
connection with your computer. It also contains information for
installing the printer driver, fonts and Remote Printer Console Program.
(HL-730 /730Plus series only)
2. Read the User’s Guide to get information about the following.
• Features and operating environment requirements of your printer –
Chapter 1
• Paper Handling – Chapter 2
• Control Panel – Chapter 3
• Options – Chapter 4
• Maintenance – Chapter 5
• Troubleshooting – Chapter 6
• Specifications – Appendices
• Index
CHAPTER 1 –1
USER’S GUIDE
ABOUT YOUR PRINTER
Printer Overview
Paper Support
Multi-Purpose Sheet Feeder
Paper Guide
Manual Feed Slot
Top Cover
Extension Support Wire
Control Panel
Output Tray
Fig. 1-1 Front View
ON
12 3 4 5 6 78
RS-422A/RS-232C
Serial Interface Port
(HL-730/730Plus series only)
Power Switch
Parallel Interface Port
Power Cord
Fig. 1-2 Rear View
✒ Note
An RS-422A/RS-232C Serial Interface Port, containing an RS-422A/RS232C Slide Switch and DIP Switches for Serial setting is optionally
available. Some models may have this option pre-installed.
CHAPTER 1 –2
CHAPTER 1 INTRODUCTION
System Requirements in Brother Printing Solution for Windows
Check the following system requirements to setup and operate the printer
in Brother Printing Solution for Windows:
• IBM PC or compatible with 80486 SX or higher microprocessor
• Parallel interface (or printer port)
• 4 MB or more of memory (8 MB recommended)
• 10 MB of space available on your hard disk for the printer driver and all
fonts
• Microsoft Windows 95 or Windows 3.1/3.11
!
Caution
The HL-720 series printer has been designed specifically for Windows 95
and Windows 3.1/3.11. It cannot work in a DOS environment, such as
MS-DOS.
Features
This printer has the following features:
❏ 600 dpi Resolution and 6 ppm Printing Speed
True 600 dots per inch (dpi) with microfine toner and six pages per
minute (ppm) printing speed (A4 or Letter paper). The resolution and
printing speed may vary depending upon document complexity.
❏ Versatile Paper Handling
The printer has a multi-purpose sheet feeder and straight paper path
mechanism. Using this mechanism, you can load A4, letter, legal, B5,
A5 and executive sizes of paper, and various types of paper including
envelopes, postcards, organizer paper, and your custom paper size. The
multi-purpose sheet feeder also allows manual paper loading, so you
can also use labels and transparencies.
❏ Enhanced Printing Performance and User-Friendly Operation for
®
Windows
The dedicated printer driver and TrueType™-compatible fonts for
®
Microsoft Windows 95 and Windows 3.1 are available on the floppy
disk supplied with your printer. You can easily install them into your
Windows system using our installer program. The driver supports our
unique compression mode to enhance printing speed in Windows
applications and allows you to choose various printer settings including
toner saving mode, custom paper size, sleep mode, gray scale
adjustment, resolution and so forth. You can easily set these print
options through the Printer Setup Menu within the Windows Control
Panel.
CHAPTER 1 –3
USER’S GUIDE
❏ Remote Printer Console Program for DOS (For HL-730/730Plus
series Only)
The utility program, Remote Printer Console (RPC), is available on a
floppy disk supplied with your printer. When you operate your
computer in the DOS (Disk Operating System) environment, this
program allows you to easily change the default settings of the printer
such as fonts, page setup, emulations and so on.
This program also provides a status monitor program, which is a
Terminate-and-Stay Resident (TSR) program. It can monitor the
printer status while running in the background and report the current
status or errors on your computer screen.
❏ Popular Printer Emulation Support (For HL-730/730Plus series
Only)
This printer supports three popular printer emulation modes, HP
LaserJet IIP, Epson FX-850, and IBM Proprinter XL. When you use
DOS application software or Windows version 3.0 or earlier, you can
use any of these emulations to operate the printer in the 300 dpi
resolution mode. The printer also supports auto-emulation switching
between HP and Epson or HP and IBM. If you want to select the
printer emulation, you can do it using the Remote Printer Console
Program.
❏ Printer Status Monitor with Bi-directional Parallel Interface
The printer driver can monitor your printer’s status using bidirectional parallel communications. A high quality bi-directional
parallel printer cable is recommended.
The printer status monitor program can show the current status of
your printer. When printing, the animated dialog box appears on your
computer screen to show the current printing process. If an error
occurs, a dialog box will appear to let you know what to correct. For
example: when your printer is out of paper, the dialog box will display
“Paper Empty” and instructions for the proper corrective action.
®
❏ Optional Apple Macintosh Interface (For HL-730/730Plus series
Only)
An optional Apple Macintosh serial interface is available, which
allows your printer to be connected to Apple Macintosh computers.
With this option, you can use your printer with both an IBM PC, or
compatible, and an Apple Macintosh at the same time. This optional
interface board can be used as an RS-422A interface for Macintosh or
an RS-232C serial interface for an IBM PC or compatible.
CHAPTER 1–4
CHAPTER 1 INTRODUCTION
❏ Enhanced Memory Management
The printer provides its own data compression technology in the printer
hardware and the supplied printer driver software, which can
automatically compress graphic data and font data efficiently into the
printer’s memory. You can avoid memory errors and print most full
page 600 dpi graphic and text data, including larger fonts, with the
printer’s standard memory.
❏ Environment-Friendly
Economy Printing Mode
This feature will cut your printing cost by saving toner. It is useful to
obtain draft copies for proof-reading. You can select from two economy
modes—25% toner saving and 50% toner saving—through the
Windows printer driver supplied with your printer.
Sleep Mode (Power Save Mode)
When the printer is not used for a certain amount of time, sleep mode
automatically reduces power consumption. The printer consumes less
than 7 W when in sleep mode.
Low Running Cost
Since the toner cartridge is separate from the drum unit, you need to
replace only the toner cartridge after approximately 2,200 pages, which
is cost effective and ecologically friendly. (In USA, Canada and some
other areas the printer is supplied with a starter toner cartridge which
must be replaced after 1,000 pages.)
The actual number of pages printed with each toner cartridge may vary
depending on your average type of print job.
CHAPTER 1 –5
USER’S GUIDE
OPERATING AND STORAGE ENVIRONMENT
Please take note of the following before using the printer.
Power Supply
Use the printer within the specified power range.
AC power: ±10% of the rated power voltage in your country
Frequency: 50 Hz (220 V– 240 V) or 50/60 Hz (110–120 V)
The power cord, including extensions, should not exceed 5 meters (16.5
feet).
Do not share the same power circuit with other high-power appliances,
particularly an air conditioner, copier, shredder and so on. If it is
unavoidable that you must use the printer with these appliances, it is
recommended that you use an isolation transformer or a high-frequency
noise filter.
Use a voltage regulator if the power source is not stable.
Environment
The printer should be installed near a power outlet, which is easily
accessible.
Use the printer only within the following ranges of temperature and
humidity.
Ambient temperature: 10°C to 32.5°C (50°F to 90.5°F)
Ambient humidity:
20% to 80% (without condensation)
The printer should be used in a well ventilation room.
Place the printer on a flat, horizontal surface.
Keep the printer clean. Do not place the printer in a dusty place.
Do not place the printer where the ventilation hole of the printer is
blocked.
Do not place the printer where it is exposed to direct sunlight. Use a blind
or a heavy curtain to protect the printer from direct sunlight when the
printer is unavoidably set up near a window.
Do not place the printer near devices that contain magnets or generate
magnetic fields.
CHAPTER 1–6
CHAPTER 1 INTRODUCTION
Do not subject the printer to strong physical shocks or vibrations.
Do not expose the printer to open flames or salty or corrosive gasses.
Do not place objects on top of the printer.
Do not place the printer near an air conditioner.
Keep the printer horizontal when carrying.
Do not cover the slots in the top cover.
CHAPTER 1 –7
CHAPTER 2 PAPER HANDLING
CHAPTER 2
PAPER HANDLING
PAPER SPECIFICATIONS
The printer can handle paper that has the following specifications.
Paper Type
Cut sheet
Envelopes
Post Card
Organizer
Labels and
Transparencies
Paper Size
A4, Letter, Legal, B5, A5, Executive, Custom size
(70-216 x 127-356 mm, 2.75-8.5 x 5-14 inches)
DL, C5, COM-10, Monarch, 9” x 12”
70-216 x 127-356 mm, 2.75-8.5 x 5-11 inches
®
Day-Timer J, K, L, M
70-216 x 127-356 mm, 2.75-8.5 x 5-11 inches
70-216 x 127-356 mm, 2.75-8.5 x 5-14 inches
Paper Capacity in Feeder
Multi-purpose
Sheet Feeder: Up to 22 mm (0.87 inch) in height (up to the mark)
2
Approx. 200 sheets of 75 g/m (20 lb.) or 50 sheets of
2
158 g/m (42 lb.) A4/Letter paper, or 10 envelopes
2
Output Tray: Approx. 100 sheets of 75 g/m (20 lb.) A4/Letter paper
Basis Weight
Cut Sheet
2
60 to 158 g/m
(16 to 42 lb.)
Caliper
±0.03 to ±0.08 in.
(0.08 to 0.2 mm)
Moisture Content
Smoothness
4% to 6% by weight
100 to 250 (Sheffield)
Envelope
2
75 to 90 g/m
(20 to 24 lb.)
single thickness
0.0033 to 0.0058 in.
(0.084 to 0.14 mm)
single thickness
4% to 6% by weight
100 to 250 (Sheffield)
Recommended paper
Cut sheet:
Xerox 4200 (in USA) / Xerox 80 Premier Paper
(in Europe) or equivalent
Label:
Avery laser label or equivalent
Transparency: 3M CG3300 or equivalent
CHAPTER 2 –1
USER’S GUIDE
Remarks
It is recommended that you test paper, especially special sizes and types of
paper, on this printer before purchasing large quantities.
Avoid feeding labels with carrier sheets exposed, or your printer will be
damaged.
Avoid using coated paper, such as vinyl coated paper.
Avoid using preprinted or highly textured paper.
Use a recommended type of paper, especially plain paper and
transparencies, for optimum printing. For more information on paper
specifications, consult your nearest authorized sales representative or the
place of purchase of your printer.
We recommend you use label or transparencies which are designed for use
in laser printers.
We recommend you use long-grained paper for the best print quality.
If the paper has problems feeding from the multi-purpose sheet feeder, use
the manual feed slot and try again.
You can use recycled paper in this printer.
Before using paper with holes such as organizer sheets, you must fan the
stack well to avoid paper jams and misfeeds.
Before using any paper, make sure that it is not curled. If it is, you should
straighten the paper as much as possible. Feeding curled paper can cause
paper jams and misfeeds.
Fig. 2-1 Fan the Paper and
Straighten the Paper
CHAPTER 2 –2
CHAPTER 2 PAPER HANDLING
The following types of envelopes are not recommended for use.
• Damaged, curled, wrinkled, or irregularly shaped envelopes
• Extremely shiny or highly textured envelopes
• Envelopes with clasps
• Envelopes with self-adhesive closures
• Envelopes of baggy construction
• Envelopes not sharply creased
• Embossed envelopes
• Envelopes already printed by a laser printer
• Envelopes pre-printed on the inside
• Envelopes that cannot be arranged uniformly when placed in a pile
Fig. 2-2 Envelopes
Printable Area
The figure below shows the physically printable area.
(Except 9”x12” envelope)
Unprintable area
Approximately 4 mm(0.16 inch) for any sizes of paper
Fig. 2-3 Printable Area
CHAPTER 2 –3
USER’S GUIDE
MULTI-PURPOSE SHEET FEEDER
The printer has a multi-purpose sheet feeder that can feed plain paper,
envelopes, transparencies and organizer paper.
To use the multi-purpose sheet feeder, follow these steps:
1. Make sure that you have selected the proper paper source, paper size
and orientation.
✒ Note
• You may select the proper paper source, paper size, and orientation in
your application software.
• If your application software does not support your custom paper size,
select the next paper size up that is closest but larger than the custom
size. Then adjust the print area by changing the right and left margins in
your application software.
2. Make sure that the multi-purpose sheet feeder contains the selected size
of paper in the selected orientation. If necessary, change the paper in the
feeder.
3. Send your file or document to the printer.
When the printer receives data, it begins the print process by loading
paper from the multi-purpose sheet feeder. If the printer is in sleep
mode when it receives data, it will wake up and start the printing
process automatically.
CHAPTER 2 –4
CHAPTER 2 PAPER HANDLING
Loading Paper into the Feeder
To load paper into the feeder, follow these steps.
1. Open the multi-purpose sheet feeder by gently pulling the lid forward
towards you. ( ➀ ).
2. Load paper into the multi-purpose sheet feeder with the printing surface
face down. (➁ )
!
Caution
• The feeder can hold up to 200 sheets of plain paper (75 g/m , 20 lb.). If
you load too many sheets, paper jams could occur.
• Make sure that the paper is stacked below the ▼ mark.
• If there is still some paper in the feeder, you must first remove it, put it
together with the new paper and then insert the stack in the feeder.
2
Fig. 2-4 Opening the Feeder and
Loading Paper or Envelopes in the Feeder
✒ Note
If you load envelopes in the feeder, make sure they are inserted in the
direction shown above.
CHAPTER 2 –5
USER’S GUIDE
3. Move the paper guide to the paper width. ( ➀ )
!
Caution
Failure to set the paper guide to the paper size may cause paper skew or
jams.
4. Close the multi-purpose sheet feeder. ( ➁)
Fig. 2-5 Moving the Paper Guide
and Closing the Feeder
✒ Note
If the multi-purpose sheet feeder runs out of paper when you try to print,
the Alarm and Paper lamps blink to alert you to a paper empty error. You
have to load paper in the feeder and push the panel switch to cancel the
alarm and continue printing. If paper jams in the printer, the Alarm and
Paper lamps also blink. If the error is a paper jam, clear it referring to
“PAPER JAMS” in Chapter 6.
CHAPTER 2 –6
CHAPTER 2 PAPER HANDLING
Two Side Printing (Manual Duplexing)
The supplied printer driver for Windows 95 or Windows 3.1 enables
manual duplex printing. For more information about settings, see the help
text in the printer driver.
The printer prints all the even numbered pages on one side of the paper
first, and then prints all the odd pages on the reverse side of the paper.
When you have finished printing the even numbered sides of the paper, the
driver instructs you to re-insert the paper by a pop-up message on the
computer screen. Follow the instructions on how to reinsert the paper.
✒ Note
• Before re-inserting the sheets, you have to straighten them, or you will
get paper errors.
• The use of very thin or very thick paper is not recommended.
• If you encounter a double feeding error, we recommend that you hold
all sheets of paper except the front sheet while the paper is feeding.
Fig. 2-6 Notes for Manual Duplexing
✒ Note
When you use the Manual Duplex function, it is possible that paper jams
may occur or print quality might not be satisfactory.
CHAPTER 2 –7
USER’S GUIDE
MANUAL FEED SLOT
The multi-purpose sheet feeder also has a manual feed slot. You can
manually load paper sheet by sheet from this slot. You do not need to
remove paper from the multi-purpose sheet feeder when using the manual
feed slot.
❏ When you load one sheet of paper manually:
You do not need to choose manual feed in the Setup dialog box of your
printer driver. Holding the selected size of paper in the selected
orientation (Portrait or Landscape), place the side of the paper you wish
to print on face down into the manual feed slot. Align the paper at the
center of the manual feed slot, and be sure to insert it all the way. ( ➀ )
Move the paper guide of the manual feed slot to the paper width you are
using. ( ➁ )
Fig. 2-7 Moving the Paper Guide
❏ When you load more than one sheet of paper manually:
Open the Setup dialog box of the supplied Windows printer driver and
choose Manual Feed in the Paper Source section. Follow the above
instructions to load the first page. The printer automatically starts
printing. After the first page is printed, the dialog box appears and
prompts you to load the next page. Load a sheet and choose OK to
resume printing. Repeat these steps until you have finished printing all
the pages.
!
Caution
If bi-directional communication is not operational between the printer and
the computer, such as when the printer is shared on a network, the dialog
box will not appear to load the next page. Manual paper feeding is not
recommended when your printer is attached to a network.
CHAPTER 2 –8
CHAPTER 2 PAPER HANDLING
✒ Note
• Insert paper firmly into the manual feed slot.
• Be sure to load sheet by sheet when using the manual feed slot.
CHAPTER 2 –9
USER’S GUIDE
OUTPUT TRAY AND PAPER SUPPORT WIRE
The printer ejects paper with printed surfaces face down into the output tray
at the front of the printer.
When the output tray is closed, the ejected paper comes out sheet by sheet
through the slit at the front. When you open the tray, sheets can be stacked
on the tray.
Follow these steps to open the output tray:
1. Pull the top of the tray down (➀).
2. Extend the extension support wire (➁).
Fig. 2-8 Opening the Output Tray and
Extending the Extension Support Wire
You can stack up to 100 sheets in the output tray.
!
Caution
• When you use transparencies, remove each sheet immediately after
printing. Stacking sheets may cause paper curled or paper jam.
• Continuous printing with the output tray closed may cause
condensation inside the output tray.
CHAPTER 2 –10
CHAPTER 3 CONTROL PANEL
CHAPTER 3
CONTROL PANEL
LAMPS AND SWITCH
This section refers to the following lamps and switch on the printer control
panel.
Dru
m
Alar
m
R
Papeady
er
D
Tonata
er
Fig. 3-1 Lamps and Switch on Control Panel
✒ Note
When the power switch is off or the printer is in sleep mode, all lamps
including the Ready lamp are off.
Ready (Paper) Lamp
The Ready lamp indicates the current status of the printer.
Lamp
Off
❍
Blinking
❍↔●
Blinking
❍↔●
On
Printer status
The power switch is off or the printer is in sleep
mode. If the printer is in sleep mode, it will wake up
automatically when it receives data or you press the
control panel switch.
The printer is warming up.
(Blinking at 1 second intervals)
The printer is cooling down and stops printing until
the printers internal temperature lower.
(Blinking at 2 seconds intervals)
The printer is ready to print.
●
This lamp also works as the Paper lamp with the Alarm lamp. They blink
simultaneously to indicate a paper error. See “Operator Calls” in Chapter 6.
CHAPTER 3 –1
USER’S GUIDE
Data (Toner) Lamp
The Data lamp indicates the current status of the print data process.
Lamp
Off
Printer status
The printer has no print data.
❍
Blinking
❍↔●
On
●
The printer is receiving data from the computer or
the printer is processing data in memory.
Print data remains in the printer memory. If the Data
lamp is on for a long period of time and nothing has
printed, you need to press the switch to print the
remaining data.
This lamp also works as the Toner lamp with the Alarm lamp. They blink
simultaneously to indicate a toner error. See “REPLACING THE TONER
CARTRIDGE” in Chapter 5 and “Operator Calls” in Chapter 6.
Drum Lamp
The Drum lamp indicates the drum unit is nearly at the end of its life.
Lamp
Off
Printer status
The drum unit can be used.
❍
On
●
The drum unit is nearly at the end of its life.
Installing a new drum unit turns off this lamp. See
“REPLACING THE DRUM UNIT” in Chapter 5.
Alarm Lamp
The Alarm lamp blinks to indicate a printer error status such as “Cover
Open” and “Memory Full.” If any other error occurs, the printer indicates
the error by blinking the Alarm lamp with another lamp or by printing an
error report.
✒ Note
The Ready, Data and Drum lamps are used to indicate printer errors with
the Alarm lamp. See “ALARM INDICATIONS AT A GLANCE” in
Chapter 6 and take corrective action for the error.
CHAPTER 3 –2
CHAPTER 3 CONTROL PANEL
Switch
If you press the switch during printing, the printer immediately stops
printing and ejects the paper. It is recommended that you wait until the page
has finished printing, then press the switch, otherwise you will lose data on
the page.
If the printer is in sleep mode, pressing the switch wakes it up into the
ready state.
If the Data lamp is on, press the switch. The printer prints any data
remaining in the printer memory: this operation is called “Form Feed.”
If an error occurs, the printer will recover from some errors automatically.
If the error does not clear automatically, press the switch to clear the error
and continue printer operation.
Other Control Features
The printer has the following useful features:
Sleep Mode
When the printer does not receive data for a certain period of time (timeout), it enters sleep mode. Sleep mode acts as though the printer was turned
off. The default time-out is 5 minutes. While the printer is in sleep mode, all
the lamps are off and it is as if it was turned off, but the printer can still
receive data from the computer. Receiving a print file or document
automatically wakes up the printer to start printing. Pressing the switch also
wakes up the printer.
✒ Note
• When the printer goes into sleep mode, the fan will not stop until the
printer engine has cooled down.
• Sleep mode allows the print engine to cool, so the temperature of your
room and how long the printer has been in sleep mode affects the
warm-up time. This warm-up time can take up to 20 seconds. The
Ready lamp blinks to indicate that the printer is warming up.
• You can change the time out for the sleep mode with the supplied
printer driver or Remote Printer Console program. Refer to the Help
section in the printer driver or RPC program for more information
about the sleep mode setting.
CHAPTER 3 –3
USER’S GUIDE
Test Print Mode
The printer has the following test print mode. Follow these steps:
1. Make sure that the top cover is closed.
2. Hold down the switch and turn on the power switch. Keep the switch
depressed until the Drum lamp comes on.
The Drum lamp lights to indicate that the printer is in the test print
mode.
3. Press the switch again to execute the test print or hold down the
switch to select another option and release the switch to execute the
selected option.
The test print mode varies depending upon the printer model as
follows:
Lamp Lit
Drum
Choice
Test sample page
Alarm
Print Config & Print
Fonts I
Ready
Factory Reset
Data
Hex Dump Print
CHAPTER 3–4
Function
The printer prints a test sample page.
The printer returns to the ready status after
printing.
The printer prints the current configuration of
the printer and a list of the internal fonts.
The printer returns to the ready status after
printing.(HL-730/730Plus series only)
The printer is restored to the factory setting and
permanent fonts and macros are cleared.
The printer returns to the ready status after
printing.(HL-730/730Plus series only)
The printer can print data as hexadecimal values,
so that you can check data errors and problems.
To exit from this mode, you have to turn off the
printer. (HL-730/730Plus series only)
CHAPTER 4 OPTIONS
CHAPTER 4
OPTIONS
SERIAL INTERFACE BOARD RS100M (For HL-730 /
730Plus series Only)
To connect the printer to a DOS computer with a serial interface or to an
Apple Macintosh computer, you need to install the optional serial interface
board. When you have installed the serial interface board, you can share the
printer between two computers (two IBM compatible PCs or one IBM
compatible PC and one Apple Macintosh) using the parallel and serial
interfaces at the same time. Automatic interface selection is a standard
feature.
✒ Note
• The serial interface board for this printer is optional, but in some
countries the serial interface board may have been installed by either
the factory or dealer.
• The serial interface for Apple Macintosh (RS-422A) will only print at
300 dpi.
The serial interface board is installed onto the main controller board inside
the printer. For the details about installation, see the instruction guide
which was provided with the serial interface board.
Selecting the RS-422A (Apple) or RS-232C (IBM) Serial Interface
✒ Note
This section is only for printer models which have had the serial interface
installed.
!
Caution
Be sure to select the serial interface type to match your computer as
follows:
• For Apple Macintosh computers: you should not have to change any
settings because the Apple (RS-422A) setting is factory selected
(default).
• For IBM compatible PCs you should move the switch to the IBM
(RS-232C) setting.
• If you are using an Apple Macintosh on the RS-422A port and an IBM
compatible PC on the parallel port, it is not necessary to make any
changes to the switch setting.
CHAPTER 4 –1
USER’S GUIDE
If necessary, select the interface type as follows:
1. Make sure that the printer is in the off-line state.
2. Select the RS-422A(Apple) or RS-232C(IBM) interface by changing
the serial interface slide switch to the right for IBM(RS-232C) or to the
left side for Apple(RS-422A).
Fig. 4-1 Selecting the RS-422A (Apple)
or RS-232C (IBM) Serial Interface
Setting the Serial Interface Parameters
✒ Note
This section is only for printer models which have had the serial interface
installed.
!
Caution
Be sure to set the parameters to match your computer as follows:
• Never change the RS-422A parameters for Apple Macintosh
computers. Because the RS-422A parameters have been correctly set at
the factory for Apple Macintosh computers, you do not need to change
the settings. You may skip this section. If you change parameters for the
RS-232C serial interface and you switch back to RS-422A for Apple
Macintosh computers, be sure to restore the parameters to the factory
settings.
• Set the RS-232C parameters to match your computer. You can set serial
settings in several different places, within your DOS application, within
the Windows Printer Icon (for Windows application software only), or
within your AUTOEXEC.BAT file using MODE commands. For
information on serial interface parameters, see the user’s guide of your
computer or software.
CHAPTER 4 –2
CHAPTER 4 OPTIONS
If necessary, set the serial interface parameters as follow:
1. Make sure that the printer is in the off-line state.
2. Set the serial interface parameters by moving up (on) or down (off) the
selectors of the dual in-line package (DIP) switch.
ON
12 3 4 5 6 78
Fig. 4-2 Setting the Serial Interface Parameters
Table 1: Serial Interface Parameters Settings
Selector
1
2
3
4
5
6
7
8
Parameters
Baud Rate
Baud Rate
Data Length
Stop Bit
Parity
Parity
Protocol
Robust Xon
On (up)
— See Table 2.
— See Table 2.
7 bits
2 bits
— See Table 3.
— See Table 3.
Xon/Xoff + DTR
On
Off (down)
—
—
8 bits
1 bit
—
—
DTR only
Off
For RS-422A
57600
9600
1200
19200
For RS-232C
9600
4800
1200
19200
Table 2: Baud Rate Settings
Selector 1
Off
On
Off
On
Selector 2
Off
Off
On
On
CHAPTER 4 –3
USER’S GUIDE
Table 3: Parity Settings
Selector 1
On
On
Off
Selector 2
On
Off
—
Parity
Odd
Even
None
✒ Note
• The factory settings are indicated in bold.
• If the robust Xon setting is turned on with selector 8, the printer sends
Xon signals at one second intervals to the connected computer until it
receives data. It is effective only if selector 7 is set to the On position for
the Xon/Xoff plus DTR setting.
Connecting the Serial Interface Cable
✒ Note
This section is only for printer models which have had the serial interface
installed.
You need a serial interface cable with an 8-pin, DIN-type connector to
connect your printer and computer.
✒ Note
• Consult your dealer for a serial interface cable.
• If you are a Macintosh user, you can easily find the necessary cable at a
local computer store. Look for Apple serial cables labeled as
“Macintosh to ImageWriter II or “Macintosh to Personal
LaserWriter 300” or the “Apple System Peripheral 8 Cable”. Do not
purchase a serial cable labeled as “Straight-through” or
“LocalTalk.”
• If you are a PC user, you need to purchase a special serial cable from
your dealer. If you have a 9-pin connector on your computer, look for a
cable labeled “IBM AT to ImageWriter II” cable. If you have a 25-pin
connector, look for a cable labeled “DB25 to ImageWriter II.” These
cables most likely would be found in the Apple Macintosh section at
your computer dealer. For more information about the interface
specification, consult your dealer.
CHAPTER 4 –4
CHAPTER 4 OPTIONS
You can connect a parallel and a serial interface cable at the same time. The
auto interface selection function allows you to share the printer with two
computers. To do this, connect the parallel interface cable and then connect
the serial interface cable as follows:
1. Make sure that the power switch is turned off.
!
Caution
Be sure to turn off the power switch before connecting or disconnecting the
interface cables, or the printer may be damaged.
2. Insert and secure the parallel interface connector into the parallel
interface port of your printer.
3. Insert and secure the serial interface connector into the serial interface
port of your printer.
4. Turn on the power switch.
CHAPTER 4 –5
USER’S GUIDE
MEMORY BOARD
Additional memory is useful and maybe necessary if you printing a very
complex document. Since Brother Printing Solution for Windows relies
on effective data compression to ‘squeeze’ a large print job into a smaller
space, there are times when data compression cannot squeeze a complex
600 dpi document into a smaller space and a resulting “Print Overrun”
error message may occur. When this occurs, you may choose to purchase
additional memory, or make changes to your printer driver settings (such
as reduce print resolution from 600 to 300 dpi, or change Half Tone
setting to Line Art or Photo Graphics).
The HL-720 series printer has 0.5 MB of memory as standard. The
memory capacity can be expanded up to 2 MB with an optional memory
board. Only one size of memory board is available as an option, giving
1.5 MB memory expansion.
The HL-730 series printer has 0.5 MB of memory as standard. The
memory capacity can be expanded up to 2 MB with an optional memory
board. Two sizes of memory boards are optionally available: 1 MB
memory expansion (giving you a total of 1.5 MB) or 1.5 MB memory
expansion (giving you a total of 2 MB). Only one memory board can be
installed, so select your board carefully according to your printing needs.
The HL-730Plus series printer has 1.0 MB of memory as standard. The
memory capacity can be expanded up to 2 MB with an optional memory
board. Only one size of memory boards is available as an option, giving
1.0 MB memory expasion.
HL-720 series
HL-730 series
HL-730Plus series
1.0 MB
N/A
MB-110
MB-110
1.5 MB
MB-215W
MB-115
N/A
These memory options may be purchased directly from Brother or from
an authorized Brother dealer/retailer.
The memory board is installed onto the main controller board inside the
printer. For the installation details, please see the Instruction guide which
is provided with the memory board.
CHAPTER 4–6
CHAPTER 5 MAINTENANCE
CHAPTER 5
MAINTENANCE
REPLACING THE TONER CARTRIDGE
The printer can print approximately 2,200 pages with one toner cartridge.
When the toner cartridge is running low, the Alarm and Data (Toner) lamps
blink once every 5 seconds to indicate toner low. In USA, Canada and some
other areas the printer is supplied with a starter toner cartridge which must
be replaced after 1,000 pages.
✒ Note
• Actual page count will vary depending on your average document type.
(i.e.: standard letter, detailed graphics, etc.)
• It is recommended that you always keep a new toner cartridge ready for
use for when you get the toner low warning.
• Discard the used toner cartridge according to local regulations. If you
are not sure of them, consult your local dealer. Be sure to seal up the
toner cartridge tightly so that toner powder does not spill out of the
cartridge. Do not discard used toner cartridges together with domestic
rubbish.
• It is recommended that you clean the printer when you replace the toner
cartridge. See “CLEANING THE PRINTER” in this chapter.
Dru
m
Ala
rm
R
Papeady
er
D
Tonata
er
Fig. 5-1 Toner Low and Empty Indication
!
Caution
You may print approximately 100 pages after the first toner low indication.
Both Alarm and Data (Toner) lamps will blink continuously to indicate that
the toner is empty. Once this indication appears, your printer cannot resume
printing until you have installed a new toner cartridge.
CHAPTER 5 –1
USER’S GUIDE
!
Caution
Keep the drum unit level after removing the toner cartridge, to avoid
possible toner spill or scatter.
Follow these steps to replace the toner cartridge:
1. Turn off the power switch.
2. Close the output tray and open the top cover. Remove the drum unit by
holding each side of the drum and gently lifting the drum forwards
towards you.
✒ Note
Make sure that the top cover is correctly latched open, indicated by a click
Fig. 5-2 Removing the Drum Unit
✒ Note
It is recommended to put the drum unit on a piece of disposable paper or
cloth in case of accidental toner spill or scatter.
CHAPTER 5 –2
CHAPTER 5 MAINTENANCE
Warning
After you have just used the printer, some internal parts of the printer
are extremely hot. When you open the top cover of the printer, never
touch the shaded parts shown in the following illustration.
High Temperature
Fig. 5-3 Inside the Printer
3. Gently turn the lever on the toner cartridge forward until it stops.
✒ Note
The toner cartridge cannot be removed unless the shutter is completely
closed by turning the lever fully to the front.
Fig. 5-4 Turning the Lever to Close the Shutter
CHAPTER 5 –3
USER’S GUIDE
4. Remove the old toner cartridge from the drum unit by pulling it out
gently.
Fig. 5-5 Removing the Old Toner Cartridge
!
Caution
Handle the toner cartridge carefully. If toner scatters on your hands or
clothes, wipe or wash it off with cold water immediately.
5. Unpack the new toner cartridge, gently shake it five or six times and
then remove the protective part.
!
Caution
• Only unpack the toner cartridge immediately before installing it into the
printer. If toner cartridges are left unpacked for a long period of time,
the toner life is shortened.
• You can only use a Brother genuine toner cartridge (TN-200 series)
which is specially formulated to ensure top print quality. Using
another brand of toner cartridge could void your printer’s
warranty.
Fig. 5-6 Shaking the Toner Cartridge
and Remove the Protective Part
CHAPTER 5 –4
CHAPTER 5 MAINTENANCE
6. Install the new toner cartridge into the right hand side of the drum unit.
Make sure that the toner cartridge guide bar is exactly aligned with the
guide slot in the drum unit and pushed fully home into the drum unit to
ensure that the toner cartridge and the drum unit fit together correctly.
Fig. 5-7 Installing the Toner Cartridge
into the Drum Unit
7. Gently turn the lever on the toner cartridge backward until it stops.
Fig. 5-8 Turning the Lever to Open the Shutter
8. Re-install the drum unit into the printer and close the top cover. Then,
turn on the power switch.
CHAPTER 5 –5
USER’S GUIDE
REPLACING THE DRUM UNIT
The printer uses a drum unit to create the print images on paper. If the Drum
lamp is on, it indicates the drum unit is nearly at the end of its life. We
recommend you prepare a new drum unit to replace the current one. Even if
the Drum lamp is on, you may be able to continue to print without replacing
the drum unit for a while. If there is a noticeable deterioration in the output
print quality even before the Drum lamp lights, then the drum unit should
be replaced.
Dru
m
Ala
rm
R
Papeady
er
D
Tonata
er
Fig. 5-9 Drum Unit Nearly at the End of its Life
!
Caution
• When removing the drum unit, handle carefully as it may contain toner.
• You should clean the printer when you replace the drum unit. See
“CLEANING THE PRINTER” in this chapter.
✒ Note
The drum unit is a consumable, and it is necessary to replace it periodically.
There are many factors that determine the actual drum life, such as
temperature, humidity, type of paper and toner that you use, the number of
pages per print job, etc.. The drum life is estimated at approximately 20,000
pages at 20 pages per job and 8,000 pages at 1 page per job. The actual
number of pages that your drum will print may be significantly less than
these estimates. Because we have no control over the many factors that
determine the actual drum life, we cannot guarantee a minimum number of
pages that will be printed by your drum.
For best performance, use only genuine Brother toner, and the product
should only be used in a clean, dust-free environment with adequate
ventilation.
CHAPTER 5 –6
CHAPTER 5 MAINTENANCE
Follow these steps to replace the drum unit:
1. Turn off the power switch.
2. Close the output tray and open the top cover. Remove the old drum unit.
Fig. 5-10 Removing the Drum Unit
Warning
After you have just used the printer, some internal parts of the printer
are extremely hot. When you open the top cover of the printer, never
touch the shaded parts shown in the following illustration.
High Temperature
Fig. 5-11 Inside the Printer
3. Remove the toner cartridge from the drum unit and keep it in a safe
place. For more information, see “REPLACING THE TONER
CARTRIDGE” in this chapter.
✒ Note
• Discard the used drum unit according to local regulations. If you are not
sure of them, consult your local dealer/retailer. Be sure to seal up the
drum unit tightly so that toner powder does not spill out of the unit. Do
not discard used drum units together with domestic rubbish.
• It is recommended to put the drum unit on a piece of disposable paper or
cloth in case of accidental toner spill or scatter.
CHAPTER 5 –7
USER’S GUIDE
Fig. 5-12 Removing the Toner Cartridge
4. Unpack the drum unit and gently shake it five or six times horizontally.
Fig. 5-13 Shaking the Drum Unit
!
Caution
• Do not remove the starter sheet.
Starter Sheet
Fig. 5-14 Do Not Remove the Starter Sheet
• Only unpack a drum unit immediately before installing it into the
printer. If an unpacked drum unit is subjected to excessive direct
sunlight or room light, the unit may be damaged.
• Handle the toner cartridge and the drum unit carefully as it contains
toner. If toner scatters and your hands or clothes get dirty, wipe or wash
it off with cold water immediately.
CHAPTER 5 –8
CHAPTER 5 MAINTENANCE
5. Install the toner cartridge into the new drum unit. For more information,
see “REPLACING THE TONER CARTRIDGE” in this chapter.
6. Install the new drum unit into the printer.
Fig. 5-15 Installing the Drum Unit
7. Close the top cover.
8. Turn on the power switch. The printer can automatically ejects the
starter sheet. Ejecting this sheet resets the drum life alarm.
Starter Sheet
Fig. 5-16 Ejecting the Starter Sheet
CHAPTER 5 –9
USER’S GUIDE
ADJUSTING THE PRINT DENSITY
The print density dial is located inside the printer. You can use it to adjust
the amount of toner applied to the paper.
When the toner cartridge and drum unit are replaced, or if the operating
temperature and humidity are high or low, print conditions may change
causing darker or lighter printouts.
Use a screwdriver to turn the print density dial gently clockwise for darker
printouts and counterclockwise for lighter printouts. The dial has been
factory set to the middle position.
Fig. 5-17 Adjusting the Print Density Dial
Warning
After you have just used the printer, some internal parts of the printer
are extremely hot. When you open the top cover of the printer, never
touch the shaded parts shown in the following illustration.
High Temperature
Fig. 5-18 Inside the Printer
CHAPTER 5 –10
CHAPTER 5 MAINTENANCE
CLEANING THE PRINTER
Clean the printer exterior and interior periodically. If printed pages get
stained with toner, clean the printer interior and drum unit.
Cleaning the Printer Exterior
Clean the printer exterior as follows:
1. Turn off the power switch and unplug the power cord.
Warning
There are high voltage electrodes inside the printer. Before cleaning
the printer, make sure to turn off the power switch and unplug the
power cord from the power outlet
Fig. 5-19 Turning off the Switch and Unplugging
2. Remove the paper in the multi-purpose sheet feeder.
3. Use a damp cloth for cleaning.
!
Caution
Use water or neutral detergents for cleaning. Cleaning with volatile liquids
such as thinners or benzene will damage the surface of the printer.
4. Wipe dirt and dust away from the printer exterior and feeder with a
cloth.
5. Load paper into the multi-purpose sheet feeder, and plug in the power
cord.
CHAPTER 5 –11
USER’S GUIDE
Cleaning the Printer Interior and Drum Unit
Clean the printer interior and the drum unit as follows:
1. Turn off the power switch and unplug the power cord.
Warning
There are high voltage electrodes inside the printer. Before cleaning
the printer, make sure to turn off the power switch and unplug the
power cord from the outlet
Fig. 5-20 Turning off the Switch and Unplugging
2. Open the top cover of the printer.
3. Take the drum unit out of the printer and put it aside.
Warning
After you have just used the printer, some internal parts of the printer
are extremely hot. When you open the top cover of the printer, never
touch the shaded parts shown in the following illustration.
High Temperature
Fig. 5-21 Inside the Printer
CHAPTER 5 –12
CHAPTER 5 MAINTENANCE
4. Gently wipe the scanner window with a soft dry cloth.
Scanner Window
Fig. 5-22 Cleaning the Scanner Window
!
Caution
• Do not touch the scanner window with your finger.
• Do not wipe the scanner window with cleaning alcohol (isophorol).
5. Turn the drum unit upside down carefully.
!
Caution
Handle the drum unit carefully as it contains toner. If toner scatters and
your hands or cloths get dirty, wipe or wash it off with cold water
immediately.
✒ Note
It is recommended to put the drum unit on a piece of disposable paper or
cloth in case of accidental toner spill or scatter.
CHAPTER 5 –13
USER’S GUIDE
6. Clean the primary corona wire inside the drum unit by gently sliding the
tab to the right and left several times.
Home Position (▲)
Fig. 5-23 Cleaning the Primary Corona Wire
7. Return the tab to the home position (▲ mark position) before
reinstalling drum unit.
!
Caution
Be sure to position the tab at the home position, or printed pages may have
vertical stripes.
8. Install the drum unit into the printer.
See the section “REPLACING THE DRUM UNIT” in Chapter 5.
9. Close the top cover.
10. Plug in the power cord and turn on the power switch.
CHAPTER 5 –14
CHAPTER 5 MAINTENANCE
RE-PACKING THE PRINTER
!
Caution
Whenever you transport the printer, use the packing materials which are
provided with your printer. Also, follow the steps below to re-pack the
printer, or the printer may be damaged which will void the printer’s
warranty.
1. Turn off the power switch and unplug the printer from the AC outlet.
2. Open the top cover.
3. Remove the drum unit assembly, referring to the previous section.
✒ Note
Remove the drum unit assembly with the toner cartridge included.
Fig. 5-24 Removing the Drum Unit Assembly
CHAPTER 5 –15
USER’S GUIDE
4. Place the drum unit assembly in the plastic bag and seal the bag
completely.
Fig. 5-25 Placing the Drum Unit in the Plastic Bag
5. Close the top cover, the extension wire, and the output tray.
6. Wrap the printer in the plastic bag and place it in the original carton
box with the original Styrofoam packing material.
7. Place any documents (manual and any documentation describing the
reason for repacking printer), and drum unit assembly in the carton
box as shown below.
8. Close the carton box and tape it.
Manuals
Drum Unit
Including Toner
Cartridge
Printer
Carton
Fig. 5-26 Repacking the Printer
CHAPTER 5–16
CHAPTER 6 TROUBLESHOOTING
CHAPTER 6
TROUBLESHOOTING
ALARM INDICATIONS AT A GLANCE
Operator Calls
If a recoverable error occurs, the printer indicates an ‘operator call’ by
blinking the Alarm lamp and any of the following lamps.
Find the error and take the proper action to correct it. The printer
automatically recovers from most errors, but you may need to reset the
printer with the panel switch as described below.
Blinking Lamp
Paper ❍↔●
Alarm❍↔●
Error
Paper jam
Paper empty
Toner ❍↔●
Alarm❍↔●
(every 5 seconds)
Toner ❍↔●
Alarm❍↔●
(Fast blinking)
Misfeed
Toner low
Toner Empty
Action
Clear the paper jam referring to the next section
“PAPER JAMS” and press the panel switch if the
printer does not automatically resume printing.
Load paper in the printer referring to Chapter 2 and
press the panel switch.
Reinstall the paper and press the panel switch.
Indicates that the printer has approximately 100
pages of printing left before the toner cartridge is
empty. Prepare a new toner cartridge.
Replace the toner cartridge with a new one
referring to Chapter 5.
CHAPTER 6 –1
USER’S GUIDE
For errors shown below, the printer indicates an operator call by blinking
the Alarm lamp. If you use the printer with the supplied Windows driver,
the status monitor will appear to indicate the error on your computer
screen. (All of HL-700 series) The HL-730/730Plus series printer also
prints some error messages on paper.
Error
Cover Open
Print Overrun
Action
Close the top cover of the printer.
• Press the panel switch to print the data remaining in the printer.
• If you use the supplied Windows driver, try again after turning
on Error Recovery in the PRINT menu of your application
software, (Refer to Help section in Windows printer driver for
the details.) or expand the printer memory with an optional
memory board.
• If this does not clear the error, reduce the complexity of your
document or reduce the print resolution.
• Press the panel switch to print the data remaining in the printer.
• Reduce the print resolution or reduce the complexity of your
document.
• Expand the printer memory with an optional memory board.
Memory Full
(For HL-730/730Plus
series Only)
This error can occur
only when using DOS
or Macintosh.
Parallel Interface Line • Press the panel switch to resume printing.
• Check that the connection between your computer and printer is
Error
secure and correct, and check the interface cable.
• Press the panel switch to resume printing.
Serial Interface
• Check the communication parameters such as baud rate and
Framing Error
stop bit on both your computer and printer.
(For HL-730/730Plus
series Only)
Serial Interface Parity • Press the panel switch to resume printing.
• Check the communication parameters such as bit length and
Error
parity on both your computer and printer.
(For HL-730/730Plus
series Only)
• Press the panel switch to resume printing.
Serial Interface
• The interface hardware may be damaged. Consult your dealer.
Overrun Error
(For HL-730/730Plus
series Only)
Serial Interface Input • Press the panel switch to resume printing.
• Check the communication parameters such as the handshake
Buffer Overflow
protocols on both your computer and printer.
(For HL-730/730Plus
• If the error occurs again, the interface hardware may be
series Only)
damaged. Consult your dealer.
CHAPTER 6 –2
CHAPTER 6 TROUBLESHOOTING
✒ Note
If the printer does not operate as you expect it to, it is recommended that
you turn off the power switch, wait a few seconds and then turn it on again.
If you still have problems, consult your dealer or our authorized service
representative.
CHAPTER 6 –3
USER’S GUIDE
Service Calls
If an unrecoverable error occurs, the printer indicates the need for a service
call by lighting all the lamps and then the following combination of lamps
alternately:
Service Call
Drum
Alarm
Ready
Data
Fuser
malfunction
●
❍
❍
❍
Service Call
Drum
Alarm
Ready
Data
D-RAM error
●
❍
●
❍
Service A
❍
●
●
❍
Service B
●
●
●
❍
Service C
❍
❍
❍
●
Service Call
Drum
Alarm
Ready
Data
Service D
●
❍
❍
●
Service E0
❍
●
❍
●
Service E1
●
●
❍
●
Service P
❍
❍
●
●
Service Call
Drum
Alarm
Ready
Data
NV-RAM
error
●
❍
●
●
Laser BD
malfunction
❍
●
❍
❍
Scanner
malfunction
●
●
❍
❍
● ON
ROM error
❍
❍
●
❍
❍ OFF
If you see any of these service call indications, turn off the power switch,
wait a few seconds and then turn it on again and try to print again.
If you cannot clear the error and see the same service call indication after
turning on the printer, consult your dealer or our authorized service
representative. Report the error status and situation referring to the above
table.
✒ Note
Be sure that the top cover and the main controller board are firmly installed.
CHAPTER 6 –4
CHAPTER 6 TROUBLESHOOTING
PAPER JAMS
Before you can clear a paper jam error, you need to find the location of the
paper jams. Locate the position referring to the following figure.
Paper
Top Cover
Multi-Purpose
Sheet Feeder
Drum Unit
Fig. 6-1 Locating Paper Jam Position
After locating the position, clear the jammed paper referring to the
following descriptions. If the jammed paper is removed completely and the
top cover is closed, the printer may resume printing automatically. If the
printer does not resume printing, press the control panel switch.
Warning
After you have just used the printer, some internal parts of the printer
are extremely hot. When you open the top cover of the printer, never
touch the shaded parts shown in the following diagram.
High Temperature
Fig. 6-2 Inside the Printer
CHAPTER 6 –5
USER’S GUIDE
!
Caution
Do not pull jammed paper from the output tray. Be sure to open the top
cover to remove the jam, or the fuser may get dirty with toner powder and
may result in toner scatter on the next printed page or pages.
Fig. 6-3 Do Not Pull the Jammed Paper from the Output Tray
❏ Paper Jam in the Multi-Purpose Sheet Feeder
If a paper jam has occurred inside the multi-purpose sheet feeder, open
the multi-purpose sheet feeder to pull the jammed paper upward out of
the feeder; then close the multi-purpose sheet feeder. Also, open the top
cover and check that a torn piece of paper does not remain inside the
printer referring to the next section.
Fig. 6-4 Paper Jam in the Feeder
If the paper cannot be pulled up, see the next section “Paper Jam near
the Drum Unit.”
CHAPTER 6 –6
CHAPTER 6 TROUBLESHOOTING
❏ Paper Jam near the Drum Unit or at the Paper Output Tray
If a paper jam has occurred near the drum unit, open the top cover and
remove the drum unit. Then, pull the jammed paper upwards and out of
the printer. Install the drum unit and close the top cover.
Fig. 6-5 Paper Jam near the Drum Unit
❏ Paper Jam in the Fuser Unit
If a paper jam has occurred in the fuser unit, open the top cover and
remove the drum unit. Then, pull the jammed paper out of the fuser.
Install the drum unit and close the top cover.
Fig. 6-6 Paper Jam Inside the Printer
CHAPTER 6 –7
USER’S GUIDE
Q&A
This section contains questions and answers for using your printer. If you
have encountered a problem, find the question relating to your problem and
take the steps recommended to correct the problem.
Setting Up the Printer Hardware
Question
The printer does not work. All
lamps are off.
The printer does not print.
Recommendation
The printer may be in sleep mode. Press the panel
switch to wake up the printer. Check to see if the
printer is plugged into a live power source and the
power switch is on.
Check the following:
• The printer is turned on.
• All of the protective parts have been removed.
• The toner cartridge and drum unit are installed
properly.
• The interface cable is securely connected between
the printer and computer.
• Check to see if the Alarm lamp is blinking. If the
lamp is blinking, refer to the Operator Call section
of this manual.
• Check to see if the Ready lamp is blinking. If the
lamp is blinking fast, the printer might be cooling
down to lower the printers internal temperature.
Open the top cover of the printer to lower the
temperature.
Setting Up the Printer for Windows
Question
I cannot print from my
application software.
Sometimes I get a Print Overrun
error when printing certain
documents from Windows.
CHAPTER 6 –8
Recommendation
• Make sure the supplied Windows printer driver is
installed and selected with your application
software.
• If you use the serial interface, make sure that the
serial slide switch of the serial interface is in the
correct position and the interface settings are
correctly set up with the DIP switches. (For HL730/730Plus series Only)
• If you are using the supplied Windows driver, turn
error recovery operation on in the Setup dialog box
and try again.
• Reduce the print resolution or reduce the
complexity of your document and try again.
• Expand the printer memory by installing one of the
optional memory boards.
CHAPTER 6 TROUBLESHOOTING
Setting Up the Printer for DOS (For HL-730/730Plus series Only)
Question
I cannot print from my
application software.
The printer prints, but it prints
incorrect information.
Sometimes it prints a couple of
characters and then ejects the
page, etc.
The printer does not print when
I press the Print Screen Key.
(Data lamp On)
The printer prints the first part
of my document but does not
print the last page.
(Data lamp On)
How can I change the User
settings or default settings of
the printer?
Recommendation
• Check if the DOS application software interface
settings match that of your printer: for example, if
you are using a parallel printer cable, you would
most likely set your DOS software printer port to
LPT1.
• Check if the printer has any printer alarms active.
• If the serial interface is used, make sure that the
RS-232C serial interface is selected with the slide
switch. Make sure that the interface settings are
correctly set up with the proper DIP switches.
Make sure the serial parameters of baud rates,
parity and stop bits match between your application
software and the printer.
This is an indication that your application printer
emulation setting and the printer’s emulation do not
match. Check in your application software which
printer you have selected to make sure the printer is set
up correctly. Remember this printer emulates three
widely used printer selections: HP LaserJet IIP, Epson
FX-850, and IBM Proprinter XL. Try setting the
printer into HP emulation and then select the HP
LaserJet IIP printer in your application software.
Press the panel switch. The data has been sent to the
printer but the printer did not receive the Page Eject
command: print screens do not send this command.
This was a common problem with database software
and spreadsheet software when not correctly set up.
The data has been sent to the printer but the printer did
not receive the Page Eject command. Press the panel
switch to eject the page. Then check with your
software supplier on how to add a Page Eject (or Form
Feed) command to the end of your print job.
Use the remote printer console (RPC) program.
CHAPTER 6 –9
USER’S GUIDE
Setting Up the Printer for Apple Macintosh Computers When the
Optional RS-100M Serial Interface Is Installed into Your Printer
(For HL-730/730Plus series Only)
Question
I cannot print from my
application software.
Recommendation
• Make sure that the supplied Macintosh printer
driver is installed in the System Folder and it is
selected with Chooser.
• Check the PORT selection within the Chooser: it
should match the port to which you physically
attached the printer cable.
• The serial slide switch of the optional interface
board should be in the Apple (RS-422A) position.
• Check the printer cable type: you cannot use a
LocalTalk or straight-through cable. Refer to
Chapter 4 for details on printer cable type.
Paper Handling
Question
The printer does not load paper.
The printer does not load paper
from the manual feed slot.
How can I load envelopes?
What paper can I use?
How can I clear paper jams?
CHAPTER 6 –10
Recommendation
• Check to see if the “Paper Empty” message appears
on your computer screen or the Alarm and Paper
lamps are blinking on the printer control panel. If
so, the multi-purpose sheet feeder may be out of
paper or not properly installed. If it is empty, load a
new stack of paper into the feeder.
• If there is paper in the multi-purpose sheet feeder,
make sure it is straight. If the paper is curled, you
should straighten it before printing. Sometimes it is
helpful to remove the paper, turn the stack over and
put it back into the paper tray.
• Reduce the amount of paper in the multi-purpose
sheet feeder, then try again.
Re-insert the paper firmly, one sheet at a time.
You can load envelopes from either the multi-purpose
sheet feeder or the manual feed slot. Your application
software must be set up correctly to print on the
envelope size you are using. This is usually done in the
page setup or document setup menu of your software.
Refer to your application manual.
You can use plain paper, envelopes, transparencies,
labels, and organizer paper. For information on loading
paper, see “Paper Handling” in Chapter 2.
See “PAPER JAMS” in this chapter.
CHAPTER 6 TROUBLESHOOTING
Printing
Question
The printer prints unexpectedly
or it prints garbage.
The printer cannot print full
pages of a document. An error
message “Print Overrun”
occurs.
The printer prints the first
couple of pages correctly, then
some pages have text missing.
(For HL-730/730Plus series
Only)
The printer cannot print full
pages of a document. A
"Memory Full" error message
occurs.
(For HL-730/730Plus series
Only)
My headers or footers appear
when I view my document on
screen but do not show up when
I print them.
Recommendation
• Turn on and off the printer or reset the printer.
• Make sure your application software is correctly set
up to use this printer by checking the printer
settings in your application software.
• Check the printer emulation settings. If you can use
the supplied RPC program, use it to change the
settings as required. Also, you can print the current
setting list from the RPC program or Printer
Control Panel. (For HL-730/730Plus series Only)
• Make sure that the correct interface type and
settings are set up to match your computer. Be sure
to use the RS-422A serial interface for Macintosh
computers and the RS-232C serial interface for
PCs. Refer to “SERIAL INTERFACE BOARD
RS100M” in Chapter 4. (For HL-730/730Plus
series Only)
The printer received a very complex print job and
could not process part of the page. This may be solved
by the following ways.
• If you are using Windows 95 or Windows 3.1 with
the supplied printer driver, see the “Setting up the
Printer for Windows” section.
• Try to reduce the complexity of your document or
reduce the print resolution.
This is a problem usually relating to serial interface
settings. Your computer is not recognizing the printer’s
input buffer full signal. Causes could be incorrect
serial cable (incorrectly wired or too long) or incorrect
setting of your computer serial interface.
• Expand the printer memory by installing one of the
optional memory boards.
• Reduce the printer resolution.
• Reduce the complexity of your document and try
again.
• Reduce the graphic quality or the number of font
sizes within your application software.
Most laser printers have a restricted area that cannot be
printed on. Usually the first two lines and last two lines
of text cannot print (leaving 62 printable lines). Adjust
the top and bottom margins in your document to allow
for this.
CHAPTER 6 –11
USER’S GUIDE
Print Quality
!
Caution
You will clear a print quality problem by replacing the drum unit with a
new one if the Drum lamp is on. The drum unit is at the end of its life.
Question
Printouts are too dark or light.
Printed pages contain white
stripes.
Recommendation
Turn the print density dial counterclockwise for lighter
images and clockwise for darker images. It has been
factory set to the middle position. See “ADJUSTING
THE PRINT DENSITY” in Chapter 5.
You may clear the problem by wiping the scanner
windows with a soft cloth. (See “Cleaning the printer
interior and Drum unit.” in Chapter 5.)
Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together rightA
now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come togetherA
right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. A
Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to beA
free. Come together right now, over me. Here come Flat-top ,he come. Lucy in the sky with Diamonde. AA
One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,heAA
come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top
,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flattop ,he come. One thing I can tell you is you go to be free. Come together right now, over me. Lucy in the
sky with Diamonde. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. A
Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be
free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you goA
to be free. Come together right now, over me. Here come Flat-top ,he come. Lucy in the sky with AAAAA
Diamonde. One thing I can tell you is you go to be free. Come together right now, over me. Here come A
Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over me. HereA
come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over me. A
Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Flat-top ,he come. Lucy in the sky with Diamonde. One thing I can tell you is you go
to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you
go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is
you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell A
If the same problem occurs and the Drum lamp is still
on after cleaning, replace the drum unit with a new
one.
you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can
tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I
can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One A
thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come.
One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he A
come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top
,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flattop ,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come
Flat-top ,he come. Lucy in the sky with Diamonde. One thing I can tell you is you go to be free. Come AAA
Fig. 6-7 White Stripes or Faint
Images
Printed pages are stained with
toner or have vertical stripes.
Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together rightA
now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come togetherA
right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. A
Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to beA
free. Come together right now, over me. Here come Flat-top ,he come. Lucy in the sky with Diamonde. AA
One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,heAA
come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top
,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flattop ,he come. One thing I can tell you is you go to be free. Come together right now, over me. Lucy in the
sky with Diamonde. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. A
Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be
free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you goA
to be free. Come together right now, over me. Here come Flat-top ,he come. Lucy in the sky with AAAAA
Diamonde. One thing I can tell you is you go to be free. Come together right now, over me. Here come A
Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over me. HereA
come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over me. A
Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Flat-top ,he come. Lucy in the sky with Diamonde. One thing I can tell you is you go
to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you
go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is
you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell A
you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can
tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I
can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One A
thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come.
One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he A
come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top
,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flattop ,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come
Flat-top ,he come. Lucy in the sky with Diamonde. One thing I can tell you is you go to be free. Come AAA
• Clean the printer interior and the primary corona
wire of the toner cartridge. See “Cleaning the
Printer Interior and Drum Unit” in Chapter 5.
• Make sure that the tab of the corona wire is at the
home position.
If the same print problem occurs and the Drum lamp is
still on after cleaning, replace the drum unit with a new
one.
Fig. 6-8 Dark Stripes or Toner
Stains
Printed pages have white spots
in black text and graphics area.
Make sure that you use paper that meets the
specifications. Rough surface or thick media can cause
the problem.
If you still have the same problem and the Drum lamp
is on, replace the drum unit with a new one.
Fig. 6-9 White Spots
CHAPTER 6 –12
CHAPTER 6 TROUBLESHOOTING
Question
Toner scatters and stains the
printed page.
Recommendation
If toner scatters over the whole printing surface, adjust
the print density dial inside the printer counter
clockwise. See “ADJUSTING THE PRINT
DENSITY” in Chapter 5.
Clean the printer interior. See “Cleaning the Printer
Interior and Drum Unit” in Chapter 5.
Make sure that you use paper that meets specifications.
Fig. 6-10 Scattering Toner
The whole page is printed in
black.
If you still have the same problem and the Drum lamp
is on, replace the drum unit with a new one.
Wipe the electric terminals referring to “Cleaning the
Printer Interior and Drum Unit” in Chapter 5. Never
use heat-sensitive paper as it will cause this problem.
If the same problem occurs and the Drum lamp is still
on after cleaning, replace the drum unit with a new
one.
Fig. 6-11 Black Page
Nothing is printed on the page.
• Make sure that the toner cartridge is not empty.
• Wipe the electric terminals referring to “Cleaning
the Printer Interior and Drum Unit” in Chapter 5.
• Make sure that a torn piece of paper does not
remain on the scanner window.
Fig. 6-12 White Page
Printed pages are marked at
regular intervals.
Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together rightA
now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come togetherA
right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. A
Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to beA
free. Come together right now, over me. Here come Flat-top ,he come. Lucy in the sky with Diamonde. AA
One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,heAA
come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top
,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flattop ,he come. One thing I can tell you is you go to be free. Come together right now, over me. Lucy in the
sky with Diamonde. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. A
Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be
free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you goA
to be free. Come together right now, over me. Here come Flat-top ,he come. Lucy in the sky with AAAAA
Diamonde. One thing I can tell you is you go to be free. Come together right now, over me. Here come A
Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over me. HereA
come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over me. A
Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Flat-top ,he come. Lucy in the sky with Diamonde. One thing I can tell you is you go
to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you
go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is
you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell A
you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can
tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I
can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One A
thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come.
One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he A
come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top
,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flattop ,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come
Flat-top ,he come. Lucy in the sky with Diamonde. One thing I can tell you is you go to be free. Come AAA
Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together rightA
now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come togetherA
right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. A
Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to beA
free. Come together right now, over me. Here come Flat-top ,he come. Lucy in the sky with Diamonde. AA
One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,heAA
come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top
,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flattop ,he come. One thing I can tell you is you go to be free. Come together right now, over me. Lucy in the
sky with Diamonde. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. A
Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be
free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you goA
to be free. Come together right now, over me. Here come Flat-top ,he come. Lucy in the sky with AAAAA
Diamonde. One thing I can tell you is you go to be free. Come together right now, over me. Here come A
Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over me. HereA
come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over me. A
Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Flat-top ,he come. Lucy in the sky with Diamonde. One thing I can tell you is you go
to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is you
go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell you is
you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can tell A
you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I can
tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One thing I
can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come. One A
thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he come.
One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top ,he A
come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flat-top
,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come Flattop ,he come. One thing I can tell you is you go to be free. Come together right now, over me. Here come
Flat-top ,he come. Lucy in the sky with Diamonde. One thing I can tell you is you go to be free. Come AAA
Fig. 6-13 Example of Regular
Marking
The problem may disappear by itself. Try printing
multiple pages to clear this problem especially if the
printer has not been used for a long time.
If the surface of the drum has been scratched, replace
the drum unit with a new one.
If the problem does not disappear, it may be that the
drum has been marked or damaged due to excessive
exposure to light. In this case, replace the drum unit
with a new one.
CHAPTER 6 –13
USER’S GUIDE
Question
Printed pages are blurred at the
center or either edge.
Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together right now, over
me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together rightA
me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together rightA
me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together right now,
over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together rightA
now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come togetherA
now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come togetherA
now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come togetherA
right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. A
right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. A
right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come AAA
together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. A
Come together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to beA
Come together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to beA
Come together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to beA
free. Come together right now, over me. Here come Pat-top ,he come. Diamonde the skyLucy in with .
free. Come together right now, over me. Here come Pat-top ,he come. Diamonde the skyLucy in with .
free. Come together right now, over me. Here come Pat-top ,he come. Diamonde the skyLucy in with .
AA One thing I can tell you is you go to be free. Come in the sky right now, over me. Here come Pat-top
,heAA come. One thing I can tell you is you go to be free. Come together right now, over me. Here come
AA One thing I can tell you is you go to be free. Come in the sky right now, over me. Here come Pat-top
,heAA come. One thing I can tell you is you go to be free. Come together right now, over me. Here come
AA One thing I can tell you is you go to be free. Come in the sky right now, over me. Here come Pat-top
,heAA come. One thing I can tell you is you go to be free. Come together right now, over me. Here come
Pat-top ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over me. Here
Pat-top ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over me. Here
Pat-top ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over me. Here
come Flat-top ,he come. One thing I can tell you is you go to be free. Come tin the sky right now, over me.
in the sky Lucy Diamonde with . Here come Pat-top ,he come. One thing I can tell you is you go to be free.
come Flat-top ,he come. One thing I can tell you is you go to be free. Come tin the sky right now, over me.
in the sky Lucy Diamonde with . Here come Pat-top ,he come. One thing I can tell you is you go to be free.
come Flat-top ,he come. One thing I can tell you is you go to be free. Come tin the sky right now, over me.
in the sky Lucy Diamonde with . Here come Pat-top ,he come. One thing I can tell you is you go to be free.
Come AAA together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to
Come AAA together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to
Come AAA together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to
be free. A Come together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you
go to be free. together Comeright now, over me. Here come Pat-top ,he come. One thing I can tell you is
be free. A Come together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you
go to be free. together Comeright now, over me. Here come Pat-top ,he come. One thing I can tell you is
be free. A Come together right now, over me. Here come Pat-top ,he come. One thing I can tell you is you
go to be free. together Comeright now, over me. Here come Pat-top ,he come. One thing I can tell you is
you goA to be free. Come together right now, over me. Here come Pat-top ,he come. Lucy in the sky with
you goA to be free. Come together right now, over me. Here come Pat-top ,he come. Lucy in the sky with
you goA to be free. Come together right now, over me. Here come Pat-top ,he come. Lucy in the sky with
AAAAA Diamonde. One thing I can tell you is you go to be free. Come tin the sky right now, over me. Here
AAAAA Diamonde. One thing I can tell you is you go to be free. Come tin the sky right now, over me. Here
AAAAA Diamonde. One thing I can tell you is you go to be free. Come tin the sky right now, over me. Here
come A Pat-top ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over
me. HereA come Pat-top ,he come. One thing I can tell you is you go to be free. Come tin the sky right
come A Pat-top ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over
me. HereA come Pat-top ,he come. One thing I can tell you is you go to be free. Come tin the sky right
come A Pat-top ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over
me. HereA come Pat-top ,he come. One thing I can tell you is you go to be free. Come tin the sky right
now, over me. A Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together
now, over me. A Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together
now, over me. A Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together
right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come
together right now, over me. Here come v ,he come. Lucy Diamonde in the sky with . One thing I can tell
right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come
together right now, over me. Here come v ,he come. Lucy Diamonde in the sky with . One thing I can tell
right now, over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come
together right now, over me. Here come v ,he come. Lucy Diamonde in the sky with . One thing I can tell
you is you go to be free. Come tin the skyright now, over me. Here come Pat-top ,he come. One thing I
you is you go to be free. Come tin the skyright now, over me. Here come Pat-top ,he come. One thing I
you is you go to be free. Come tin the skyright now, over me. Here come Pat-top ,he come. One thing I
can tell you is you go to be free. Come in the sky right now, over me. Here come Pat-top ,he come. One
thing I can tell you is you go to be free. Come in the sky right now, over me. Here come Pat-top ,he come.
can tell you is you go to be free. Come in the sky right now, over me. Here come Pat-top ,he come. One
thing I can tell you is you go to be free. Come in the sky right now, over me. Here come Pat-top ,he come.
can tell you is you go to be free. Come in the sky right now, over me. Here come Pat-top ,he come. One
thing I can tell you is you go to be free. Come in the sky right now, over me. Here come Pat-top ,he come.
One thing I can tell A you is you go to be free. Come in the sky right now, over me. Here come Pat-top ,he
One thing I can tell A you is you go to be free. Come in the sky right now, over me. Here come Pat-top ,he
One thing I can tell A you is you go to be free. Come in the sky right now, over me. Here come Pat-top ,he
come. One thing I can tell you is you go to be free. Come in the sky right now, over me. Here come Pattop ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over me. Here come
come. One thing I can tell you is you go to be free. Come in the sky right now, over me. Here come Pattop ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over me. Here come
come. One thing I can tell you is you go to be free. Come in the sky right now, over me. Here come Pattop ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over me. Here come
Pat-top ,he come. One A thing I can tell you is you go to be free. Come in the sky right now, over me. Here
Pat-top ,he come. One A thing I can tell you is you go to be free. Come in the sky right now, over me. Here
Pat-top ,he come. One A thing I can tell you is you go to be free. Come in the sky right now, over me. Here
come Pat-top ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over me.
come Pat-top ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over me.
come Pat-top ,he come. One thing I can tell you is you go to be free. Come in the sky right now, over me.
Here come Pat-top ,he A come. One thing I can tell you is you go to be free. Come in the sky right now,
over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together right
Here come Pat-top ,he A come. One thing I can tell you is you go to be free. Come in the sky right now,
over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together right
Here come Pat-top ,he A come. One thing I can tell you is you go to be free. Come in the sky right now,
over me. Here come Pat-top ,he come. One thing I can tell you is you go to be free. Come together right
now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come tin the sky
now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come tin the sky
now, over me. Here come Flat-top ,he come. One thing I can tell you is you go to be free. Come tin the sky
right now, over me. Here come Pat-top ,he come. Lucy in the sky with Amesist. One thing I can tell you is
right now, over me. Here come Pat-top ,he come. Lucy in the sky with Amesist. One thing I can tell you is
right now, over me. Here come Pat-top ,he come. Lucy in the sky with Amesist. One thing I can tell you is
Fig. 6-14 Blurred Page
Ghost images show up on
printed pages.
Recommendation
Certain environmental conditions such as humidity,
high temperatures, etc. may cause this situation to
occur.
• Make sure that the printer is placed on a flat,
horizontal surface.
• Remove the drum unit with the toner cartridge
installed. Try shaking them from side to side.
• You may clear the problem by wiping the scanner
windows with a soft cloth. (See “Cleaning the
Printer Interior and Drum Unit.”)
If the same problem occurs after cleaning and
Drum lamp is still on, replace the drum unit with a
new one.
• Turn the print density dial counterclockwise for
lighter images. See “ADJUSTING THE PRINT
DENSITY” in Chapter 5.
• Make sure that you use paper that meets the
specifications. Rough surface or thick media can
cause the problem.
Fig. 6-15 Ghost Images
✒ Note
The drum unit is a consumable, and it is necessary to replace it periodically.
CHAPTER 6 –14
APPENDIX
APPENDIX A
PRINTER SPECIFICATIONS
Printing
Print Method
Electrophotography by semiconductor laser beam scanning
Laser
Wavelength: 780 nm
Output: 5 mW max
Resolution
HL-720 series: 600 dots/inch
(under Brother Printing Solution for
Windows)
HL-730 / 730Plus series:
600 dots/inch
(under Brother Printing Solution for
Windows)
300 dots/inch
(under DOS, Apple Macintosh and other
operating system)
Print Quality
Normal printing mode
Economy printing mode (up to 25% and 50% toner saving)
Print Speed
Up to 6 pages/minute (when loading A4 or letter-size paper
from the multi-purpose sheet feeder)
NOTE: Maximum print speed is obtained by printing several
copies of the same page. Print speed may vary depending on
interface type, emulation, processing power of the computer,
memory allocated to the print job, paper size and graphic
quality.
Warm-Up
20 seconds at 23°C (73.4°F)
(The warm up time depends on the ambient temperature and
humidity.)
First Print
20 seconds (when loading A4 or letter-size paper from the
multi-purpose sheet feeder)
Print Media
Toner cartridge:
Life Expectancy: 2,200 pages/new toner cartridge
1,000 pages/starter toner cartridge
(USA, Canada and some other areas only)
(when printing A4- or letter-size paper at 5% print coverage)
NOTE: Toner life expectancy will vary depending on the type
of average print job printed.
APPENDIX A–1
USER’S GUIDE
Drum Unit:
Life Expectancy: 20,000 pages at 20 pages per job
8,000 pages at 1 page per job
NOTE: There are many factors that determine the actual drum
life, such as temperature, humidity, type of paper and toner that
you use, the number of pages per print job, etc..
Functions
TrueType Fonts on disks
Emulation
TrueType-compatible soft-fonts for Windows on the supplied
disk
HL-720 series: Brother Printing Solution for Windows
HL-730 / 730Plus series:
Brother Printing Solution for Windows
Automatic emulation selection among HP
LaserJet IIP (PCL level 4), EPSON FX850, or IBM Proprinter XL
Printer Driver
Windows 3.1/3.11 and Windows 95 driver, supporting Brother
Native Compression mode and bi-directional capability
Optional Macintosh driver available for System 6.0.7 or higher
(For HL-730/730Plus series Only)
Interface
Bi-directional parallel
RS-422A/RS-232C serial interface (RS-100M) is optionally
available. (For HL-730/730Plus series Only)
Memory
HL-720 series :
Diagnostics
Self-diagnostic program
APPENDIX A–2
0.5 MB
Expandable up to 2 MB with an optional
memory board :
MB215W- 1.5 MB
HL-730 series:
0.5 MB
Expandable up to 2 MB with an optional
memory board (only 1 memory board can
be installed.):
MB110 - 1.0 MB
MB115 - 1.5 MB
HL-730Plus series: 1.0 MB
Expandable up to 2 MB with an optional
memory board:
MB110 - 1.0 MB
APPENDIX
Electrical and Mechanical
Power Source
U.S.A. and Canada:
Europe and Australia:
AC 110 to 120 V, 50 / 60 Hz
AC 220 to 240 V, 50 Hz
Power Consumption
Printing:
Stand-by:
Sleep:
150 W or less
35 W or less
7 W or less
Noise
Printing:
Sleep:
48 dB A or less
35 dB A or less
Temperature
Operating:
Storage:
10 to 32.5°C (50 to 90.5°F)
0 to 40°C (38 to 104°F)
Humidity
Operating:
Storage:
20 to 80% (without condensation)
20 to 80% (without condensation)
Dimensions (W x H x D)
366 x 250 x 353 mm (14.4 x 9.8 x 13.9 inches)
(when the output tray is closed.)
Weight
Approx. 6.5 kg (14.3 lb.) including the drum unit
APPENDIX A–3
USER’S GUIDE
PARALLEL INTERFACE SPECIFICATIONS
✒ Note
To ensure best quality performance use an IEEE 1284 compliant parallel
cable between the printer and your computer. Only IEEE 1284 cables
support all of the advanced printing capabilities, like bi-directional
communication. These cables will be clearly marked with “IEEE-1284”.
Interface Connector
Printer Side: Amphenol FCN-685J036-L/X or equivalent
A shielded cable should be used.
Pin Assignment
Pin No.
Signal
1
DATA STROBE
Input
2
3
4
5
6
7
8
9
10
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
DATA 8
APPENDIX A –4
Direction Pin No.
Signal
Direction
19
0V (S.G.)
–
ACKNLG
Input
Input
Input
Input
Input
Input
Input
Input
Output
20
21
22
23
24
25
26
27
28
0V (S.G.)
0V (S.G.)
0V (S.G.)
0V (S.G.)
0V (S.G.)
0V (S.G.)
0V (S.G.)
0V (S.G.)
0V (S.G.)
–
–
–
–
–
–
–
–
–
11
12
13
BUSY
PE
SLCT
Output
Output
Output
29
30
31
0V (S.G.)
0V (S.G.)
INPUT PRIME
–
–
Input
14
AUTO FEED
Input
32
FAULT
Output
15
16
17
18
N.C.
0V (S.G.)
0V (S.G.)
+5V
–
–
–
–
33
34
35
36
N.C.
N.C.
N.C.
–
–
–
Input
SLCT IN
APPENDIX
✒ Note
To use bi-directional communication, an interface cable which has the pin
connections above must be used.
Pin
1
18
2
19
3
4
20
5
6
21
7
8
22
9
10
24
11
23
12
13
14
25
16
15
17
Shield
Pin
1
19
2
20
3
21
4
22
5
23
6
24
7
25
8
26
9
27
10
28
11
29
12
17
13
15
14
30
31
33
32
34
36
35
18
16
Shield
Fig. A-1 Parallel Interface Cable
APPENDIX A–5
USER’S GUIDE
RESIDENT FONTS (For HL-730 / 730Plus series Only)
The following bitmapped fonts are resident in this printer.
Brougham 10 (12 point)
upright/normal
upright/bold
italic/normal
italic/bold
Brougham 12 (10 point)
upright/normal
upright/bold
italic/normal
italic/bold
Letter Gothic 16.66 (8.5 point)upright/normal
upright/bold
italic/normal
italic/bold
(Portrait and Landscape are available for the above.)
APPENDIX A –6
APPENDIX
SYMBOL SETS/CHARACTER SETS (For HL-730 / 730Plus
series Only)
* IBM mode
• PC-8
• PC-8 D/N
• PC-850
• PC-852
• PC-860
• PC-863
• PC-865
• PC-8 Turkish
* EPSON mode
• US ASCII
• German
• UK ASCII I
• French I
• Danish I
• Italy
• Spanish
• Swedish
• Japanese
• Norwegian
• Danish II
• UK ASCII II
• French II
• Dutch
• South African
• PC-8
• PC-8 D/N
• PC-850
• PC-852
• PC-860
• PC-863
• PC-865
• PC-8 Turkish
* HP mode
• ISO14 JIS ASCII
• ISO57 Chinese
• ISO11 Swedish
• HP Spanish
• ISO17 Spanish
• ISO10 Swedish
• ISO16 Portuguese
• ISO84 Portuguese
• ISO85 Spanish
• PC-8
• PC-8 D/N
• PC-8 Turkish
• PC-850
• PC-852
• PC-860
• PC-863
• PC-865
• Roman 8
• ISO Latin 1
(ECMA-94)
• ISO60 Norwegian 1
• ISO61 Norwegian 2
• ISO4 UK
• ISO25 French
• ISO69 French
• HP German
• ISO21 German
• ISO15 Italian
• ISO6 ASCII
• Legal
• ISO2 IRV
✒ Note
If you want to know what characters are in each symbol/character set, print
CHARSETS.PRN file from “Print form” option in Direct Access Menu of
the Remote Printer Console Program.
APPENDIX A –7
INDEX
INDEX
A
I
Alarm lamp ............................... 3–2, 6–1
auto-emulation switching .................. 1–4
interface ............................................A–2
error ...............................................6–2
B
J
baud rate............................................ 4–3
bitmapped font ................................. A–6
jammed paper ....................................6–5
C
character set...................................... A–7
control panel.............................. 1–2, 3–1
cover open......................................... 6–2
cut sheet ............................................ 2–1
D
data compression technology ............ 1–5
Data lamp .......................................... 3–2
data length......................................... 4–3
DIP switch................................. 1–2, 4–3
DOS................................................... 6–9
dpi ..................................................... 1–3
Drum lamp ........................................ 3–2
drum unit........................................... 5–6
life ................................................ A–2
DTR................................................... 4–3
duplex printing .................................. 2–7
E
economy mode .................................. 1–5
emulation...................................1–4, A–2
envelope ............................................ 2–1
error
message ......................................... 6–2
recoverable .................................... 6–1
unrecoverable ................................ 6–4
extension support wire ...................... 1–2
F
Factory Reset..................................... 3–4
H
hex dump print .................................. 3–4
L
label ...................................................2–1
M
Macintosh ................................1–4, 6–10
manual feed slot.........................1–2, 2–8
memory.............................................A–2
board ..............................................4–6
full..................................................6–2
misfeed...............................................6–1
multi-purpose sheet feeder.........1–2, 2–4
capacity ..........................................2–1
O
operator call ...............................6–1–6–3
organizer ............................................2–1
output tray................................1–2, 2–10
capacity ..........................................2–1
P
paper
capacity ..........................................2–1
empty .............................................6–1
jam .........................................6–1, 6–5
recommended.................................2–1
size .................................................2–1
type ................................................2–1
paper guide ........................................1–2
Paper lamp ................................. 3–1, 6-1
paper support .....................................1–2
parallel interface
pin assignment ..............................A–4
port.................................................1–2
parity..................................................4–4
post card.............................................2–1
Index–1
USER’S GUIDE
power cord ........................................ 1–2
power switch ..................................... 1–2
ppm ................................................... 1–3
primary corona wire ........................ 5–14
print
density ......................................... 5–10
method.......................................... A–1
overrun .......................................... 6–2
quality .......................................... A–1
speed ............................................ A–1
Print Config....................................... 3–4
Print Fonts I....................................... 3–4
printable area..................................... 2–3
printer driver .................................... A–2
printer status monitor ........................ 1–4
protocol ............................................. 4–3
R
Ready lamp ....................................... 3–1
Remote Printer Console .................... 1–4
resident font ..................................... A–6
resolution...................................1–3, A–1
robust................................................. 4–3
RPC ................................................... 1–4
RS-232C............................................ 4–2
RS-422A ........................................... 4–2
S
scanner window............................... 5–13
serial interface ................................... 4–1
cable .............................................. 4–4
parameter....................................... 4–3
RS-422A/RS-232C port ................ 1–2
service call......................................... 6–4
sleep mode ................................ 1–5, 3–3
slide switch................................. 1–2, 4-2
starter sheet ....................................... 5–9
stop bit............................................... 4–3
switch ................................................ 3–3
symbol set ........................................ A–7
T
test print mode................................... 3–4
test sample page ................................ 3–4
time-out ............................................. 3–3
toner
empty............................................. 6–1
low................................................. 6–1
toner cartridge ................................... 5–1
Index-2
life.................................................A–1
starter .............................................1–5
Toner lamp .................................3–2, 6–1
top cover ............................................1–2
transparency.......................................2–1
W
warm-up............................................A–1
Windows ............................................6–8
X
Xon/Xoff............................................4–3