Canon imageFORMULA ScanFront 330 Setup Guide

ScanFront 330
Setup and Operation Guide
Please read this manual before using the scanner.
After you finish reading this manual, keep it in a safe place
for future reference.
ScanFront 330
Setup Guide
Read This First
Please read this manual before using the scanner.
After you finish reading this manual, keep it in a safe place
for future reference.
International ENERGY STAR® Office Equipment
Program
As an ENERGY STAR® Partner, Canon
Electronics Inc. has determined that this
machine meets the ENERGY STAR® Program
guidelines for energy efficiency.
The International ENERGY STAR® Office
Equipment Program is an international program that promotes
energy saving through the use of computers and other office
equipment.
The program backs the development and dissemination of
products with functions that effectively reduce energy
consumption. It is an open system in which business
proprietors can participate voluntarily. The targeted products
are office equipment, such as computers, monitors, printers,
fax, machine, copiers, and scanners. The standards and logos
are uniform among participating nations.
This model doesn’t provide “setting options” for power
management.
Under factory default settings, the scanner will enter Low
Power mode after 12 minutes of inactivity. Although you can
change the period of time before the scanner enters Low
Power mode to up to 230 minutes, we recommend using the
default setting.
FCC REGULATIONS (For 120 V model)
Network Scanner, Model M11-1041/M11-1051/M11-1053
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician
for help.
Use of shielded cable is required to comply with class B limits
in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment
unless otherwise specified in the manual. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
Canon U.S.A. Inc.
One Canon Park, Melville, NY 11747, U.S.A.
Tel. No. (800)652-2666
RADIO INTERFERENCE REGULATIONS (For 120 V
models)
This digital apparatus does not exceed the Class B limits for
radio noise emissions from digital apparatus as set out in the
Interference-causing equipment standard entitled “Digital
Apparatus”, ICES-003 of the Industry Canada.
RÈGLEMENT SUR LE BROUILLAGE
RADIOÉLECTRIQUE (For 120 V models)
Cet appareil numérique respecte les limites de bruits
radioélectriques applicables aux appareils numériques de
Classe B prescrites dans la norme sur le matériel brouilleur:
“Appareils Numériques”, NMB-003 édictée par l’Industrie
Canada.
For CA, USA Only
Included battery contains Perchlorate Material - special
handling may apply.
See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/ for
detail.
European Union (and EEA) only.
This symbol indicates that this product is not to be
disposed of with your household waste, according
to the WEEE Directive (2002/96/EC) and your
national law. This product should be handed over
to a designated collection point, e.g., on an
authorized one-for-one basis when you buy a new similar
product or to an authorized collection site for recycling waste
electrical and electronic equipment (EEE). Improper handling
of this type of waste could have a possible negative impact on
the environment and human health due to potentially
hazardous substances that are generally associated with EEE.
At the same time, your cooperation in the correct disposal of
this product will contribute to the effective usage of natural
resources. For more information about where you can drop off
your waste equipment for recycling, please contact your local
city office, waste authority, approved WEEE scheme or your
household waste disposal service. For more information
regarding return and recycling of WEEE products, please visit
www.canon-europe.com/environment.
(EEA: Norway, Iceland and Liechtenstein)
Model Names
The following names may be provided for the safety
regulations in each sales region of the Network Scanner.
ScanFront 330: Model M11-1053
Trademarks
• Canon and the Canon logo are registered trademarks of
Canon Inc. in the United States and may also be trademarks
or registered trademarks in other countries.
• imageFORMULA is a trademark of Canon Electronics Inc.
• Microsoft, Windows, Internet Explorer, and Active
Directory are registered trademarks or trademarks of
Microsoft Corporation in the United States and other
countries.
• Adobe, Acrobat, and Adobe Reader are registered
trademarks or trademarks of Adobe Systems Incorporated in
the United States and other countries.
• Other product and company names herein may be the
trademarks of their respective owners.
Disclaimers
The information in this document is subject to change without
notice.
CANON ELECTRONICS INC. MAKES NO WARRANTY
OF ANY KIND WITH REGARD TO THIS MATERIAL,
EITHER EXPRESS OR IMPLIED, EXPECT AS
PROVIDED HEREIN, INCLUDING WITHOUT
LIMITATION, THEREOF, WARRANTIES AS TO
MARKETABILITY, MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE OF USE OR NONINFRINGEMENT. CANON ELECTRONICS INC. SHALL
NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY NATURE, OR
LOSSES OR EXPENSES RESULTING FROM THE USE
OF THIS MATERIAL.
CANON ELECTRONICS INC. IS NOT LIABLE FOR THE
STORAGE AND HANDLING OF DOCUMENTS
SCANNED WITH THIS PRODUCT, OR THE STORAGE
AND HANDLING OF RESULTING SCANNED IMAGE
DATA.
IF YOU INTEND TO DISCARD THE ORIGINALS OF
SCANNED DOCUMENTS, YOU THE CUSTOMER ARE
RESPONSIBLE FOR INSPECTING THE SCANNED
IMAGES AND VERIFYING THAT DATA IS INTACT.
THE MAXIMUM LIABILITY OF CANON
ELECTRONICS INC. UNDER THIS WARRANTY IS
LIMITED TO THE PURCHASE PRICE OF THE
PRODUCT COVERED BY THE WARRANTY.
Copyright
libtiff
Copyright (c) 1988-1996 Sam Leffler
Copyright (c) 1991-1996 Silicon Graphics, Inc.
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby
granted without fee, provided that (i) the above copyright
notices and this permission notice appear in all copies of the
software and related documentation, and (ii) the names of
Sam Leffler and Silicon Graphics may not be used in any
advertising or publicity relating to the software without the
specific, prior written permission of Sam Leffler and Silicon
Graphics.
THE SOFTWARE IS PROVIDED “AS-IS” AND
WITHOUT WARRANTY OF ANY KIND, EXPRESS,
IMPLIED OR OTHERWISE, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
IN NO EVENT SHALL SAM LEFFLER OR SILICON
GRAPHICS BE LIABLE FOR ANY SPECIAL,
INCIDENTAL, INDIRECT OR CONSEQUENTIAL
DAMAGES OF ANY KIND, OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE,
DATA OR PROFITS, WHETHER OR NOT ADVISED OF
THE POSSIBILITY OF DAMAGE, AND ON ANY
THEORY OF LIABILITY, ARISING OUT OF OR IN
CONNECTION WITH THE USE OR PERFORMANCE OF
THIS SOFTWARE.
libjpeg
Portions of this software are based in part on the work of the
Independent JPEG Group.
MD5
derived from the RSA Data Security, Inc. MD5 MessageDigest Algorithm
Copyright (c) 1998 - 2002, Paul Johnston & Contributors
All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
Neither the name of the author nor the names of its
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Copyright (c) 1991-2, RSA Data Security, Inc. Created 1991.
All rights reserved.
License to copy and use this software is granted provided that
it is identified as the “RSA Data Security, Inc. MD5 MessageDigest Algorithm” in all material mentioning or referencing
this software or this function.
License is also granted to make and use derivative works
provided that such works are identified as “derived from the
RSA Data Security, Inc. MD5 Message-Digest Algorithm” in
all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning
either the merchantability of this software or the suitability of
this software for any particular purpose. It is provided “as is”
without express or implied warranty of any kind.
These notices must be retained in any copies of any part of
this documentation and/or software.
II. The required acknowledgements for third party
components included in the OperaRBrowser engine
are as follows:
Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN
MERCURY AND MUST BE RECYCLED OR DISPOSED
OF ACCORDING TO LOCAL, STATE OR FEDERAL
LAWS.
THIS SOFTWARE IS BEING PROVIDED "AS IS",
WITHOUT ANY EXPRESS OR IMPLIED
WARRANTY.IN PARTICULAR, NEITHER THE
AUTHOR NOR LUCENT MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND
CONCERNING THE MERCHANTABILITY
OF THIS SOFTWARE OR ITS FITNESS FOR ANY
PARTICULAR PURPOSE.
Opera® or Opera Software™ are registered trademarks of
Opera Software ASA in Norway or other countries.
OPERA SOFTWARE ASA'S AND THIRD PARTY
SUPPLIER'S COPYRIGHT NOTICE AND
ACKNOWLEDGEMENTS
I. Opera Software ASAs browser/browser engine
Opera®Browser from Opera Software ASA. Copyright 19952008 Opera Software ASA. All rights reserved.
This software is being provided on an « as is »‚ basis. Opera
and its suppliers disclaim all warranties regarding the
software, either express or implied, statutory or otherwise,
including without limitation warranties of functionality,
fitness for a particular purpose or non-infringement.
1. David Gay's binary/decimal conversion code (dtoa
and strtod)
"The author of this software is David M. Gay.
Copyright (c) 1991, 2000, 2001 by Lucent Technologies.
Permission to use, copy, modify, and distribute this software
for any purpose without fee is hereby granted, provided that
this entire notice is included in all copies of any software
which is or includes a copy or modification of this software
and in all copies of the supporting documentation for such
software.
2. OpenSSL 0.9.8e (formerly SSLeay)
The OpenSSL toolkit stays under a dual license, i.e. both the
conditions of the OpenSSL License and the original SSLeay
license apply to the toolkit. See below for the actual license
texts. Actually both licenses are BSD-style Open Source
licenses. In case of any license issues related to OpenSSL
please contact openssl-core@openssl.org.
OpenSSL License
Copyright (c) 1998-2008 The OpenSSL Project. All rights
reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgment:
"This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/)"
4. The names "OpenSSL Toolkit" and "OpenSSL Project"
must not be used to endorse or promote products derived
from this software without prior written permission. For
written permission, please contact opensslcore@openssl.org.
5. Products derived from this software may not be called
"OpenSSL" nor may "OpenSSL" appear in their names
without prior written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the
following acknowledgment:
"This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit
(http://www.openssl.org/)"
THIS SOFTWARE IS PROVIDED BY THE OpenSSL
PROJECT ``AS IS'' AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE OpenSSL
PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric
Young (eay@cryptsoft.com). This product includes software
written by Tim Hudson (tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com)
All rights reserved.
This package is an SSL implementation written by Eric
Young (eay@cryptsoft.com).
The implementation was written so as to conform with
Netscapes SSL.
This library is free for commercial and non-commercial use as
long as the following conditions are aheared to. The following
conditions apply to all code found in this distribution, be it the
RC4, RSA, lhash, DES, etc., code; not just the SSL code. The
SSL documentation included with this distribution is covered
by the same copyright terms except that the holder is Tim
Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young's, and as such any Copyright
notices in the code are not to be removed.
If this package is used in a product, Eric Young should be
given attribution as the author of the parts of the library used.
This can be in the form of a textual message at program
startup or in documentation (online or textual) provided with
the package.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
The licence and distribution terms for any publically available
version or derivative of this code cannot be changed. i.e. this
code cannot simply be copied and put under another
distribution licence [including the GNU Public Licence.]
3. All advertising materials mentioning features or use of this
software must display the following acknowledgement:
"This product includes cryptographic software written by
Eric Young (eay@cryptsoft.com)"
The word 'cryptographic' can be left out if the rouines [SIC]
from the library being used are not cryptographic related
:-).
4. If you include any Windows specific code (or a derivative
thereof) from the apps directory (application code) you
must include an acknowledgement:
"This product includes software written by Tim Hudson
(tjh@cryptsoft.com)"
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS
IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
Copyright 2013 by CANON ELECTRONICS INC. All rights
reserved.
No part of this publication may be reproduced or transmitted
in any form or by any means, electronic or mechanical,
including photocopying and recording, or by any information
storage or retrieval system without the prior written
permission of CANON ELECTRONICS INC.
❏ Table of Contents
Introduction ............................................................. 1
Manuals for the Scanner ......................................... 2
Symbols Used in This Manual ................................. 2
Important Safety Instructions .................................. 3
Installation Location................................................. 3
Power ...................................................................... 3
Moving the Scanner................................................. 4
Handling .................................................................. 4
Disposal................................................................... 6
ScanFront Setup Overview ..................................... 7
1. Checking the Supplied Accessories .................... 8
2. Removing the Packing Materials and
Attaching the Feed Roller.................................... 9
3. Installing the Scanner and Connecting to a
Network ............................................................. 11
Connecting the AC Adapter................................... 11
Connecting the Network Cable.............................. 11
4. Turning the Power ON and OFF ....................... 12
Turning the Power ON........................................... 12
Turning the Power OFF ......................................... 12
5. Configuring the Scanner Settings ..................... 13
Network Settings ................................................... 14
Configuring the Date and Time and Confirming
the Time Zone ....................................................... 16
Mail Server Settings .............................................. 17
6. Scanning Procedure.......................................... 18
7. Supplied Applications ........................................ 21
ScanFront Service ................................................. 21
ScanFront Administration Tool .............................. 21
Introduction
Thank you for purchasing the Canon imageFORMULA ScanFront 330 network scanner.
Please read this manual thoroughly before using the scanner to familiarize yourself with its capabilities, and to make the most of its
many functions. After reading this manual, store it in a safe place for future reference.
About ScanFront 330
The ScanFront 330 is a network scanner that you can use without connecting to a computer.
You can transfer the data of an image scanned with the ScanFront 330 to a shared folder on a server PC or client PC on the network
or to an FTP server*, send it to a printer for printing**, or deliver it to a remote location via e-mail or Internet fax service. When
using the scanner without a network environment, you can also save the image files to USB memory.
* To send image files to a shared folder on a computer on a different segment of the network, the supplied ScanFront Service software must be
installed on a computer on the network.
** To send image files to a printer, the supplied ScanFront Service software must be installed on a computer on the network.
Shared Folder
(Server PC, Client PC)
Network
Printer
Save File
Save File
Send E-mail
Mail Server
Internet Fax Service
FTP Server
ScanFront
USB Memory
Conceptual Diagram of the ScanFront
1
❏ Manuals for the Scanner
The following manuals are provided with the Canon
ScanFront 330. Be sure to read these manuals thoroughly
before using the scanner.
Setup and Operation Guide (This Manual)*
Setup Guide
Describes the procedure for setting up the scanner for
scanning. Set up the ScanFront in accordance with the
Setup Guide. For details on the ScanFront, refer to the
Operation Guide and ScanFront 300/300P/330
INSTRUCTIONS (electronic manuals).
Operation Guide
Provides an overview of the functions of the scanner, and
describes the basic operations for using the ScanFront. For
details on the settings of the ScanFront, refer to the
ScanFront 300/300P/330 INSTRUCTIONS (electronic
manual).
* The printed version of Setup and Operation Guide may vary
depending on your region. PDF files of the Setup and Operation
Guide in other languages can be found on the application disc.
INSTRUCTIONS: Electronic Manual
Describes how to use the scanner, and includes
instructions for configuring the scanner settings, as well as
handling, maintenance, and troubleshooting information.
This manual is stored as a PDF file on the supplied
application disc and requires Adobe Reader to open. (You
can download Adobe Reader from the Adobe Web site.)
2
❏ Symbols Used in This Manual
The following symbols are used in this manual to explain
procedures, restrictions, handling precautions, and
instructions that should be observed for safety.
WARNING
Indicates a warning concerning operations that may lead to
death or injury to persons if not performed correctly. To
use the scanner safely, always pay attention to these
warnings.
CAUTION
Indicates a caution concerning operations that may lead to
injury to persons, or damage to property if not performed
correctly. To use the scanner safely, always pay attention
to these cautions.
IMPORTANT
Indicates operational requirements and restrictions. Be
sure to read these items carefully to operate the scanner
correctly, and avoid damage to the scanner.
Hint
Indicates a clarification of an operation, or contains
additional explanations for a procedure. Reading these
notes is highly recommended.
Important Safety Instructions
To ensure the safe operation of this scanner, be sure to read the safety warnings and precautions described below.
❏ Installation Location
The performance of this scanner is affected by the
environment in which it is installed. Make sure that the
location where the scanner is installed meets the following
environmental requirements.
● Provide adequate space around the scanner for
operation, maintenance, and ventilation.
At least
15.75"
(40 cm)
● Avoid exposing the scanner to rapid changes in
temperature. If the room in which the scanner is
installed is cold but rapidly heated, water droplets
(condensation) may form inside the scanner. This
may result in a noticeable degradation in scanning
quality.
The following conditions are recommended for
optimal scanning quality:
Room temperature: 10 °C to 32.5 °C (50 °F to
90.5 °F)
Humidity: 20% to 80% RH
● Avoid installing the scanner near equipment that
generates a magnetic field (e.g. speakers,
televisions, or radios).
❏ Power
At least
23.62" (60 cm)
● Avoid installing the machine in direct sunlight. If
this is unavoidable, use curtains to shade the
scanner.
● Avoid locations where a considerable amount of
dust accumulates.
● Avoid warm or humid locations, such as in the
vicinity of a water faucet, water heater, or
humidifier, and avoid locations where the fumes
from ammonia, paint thinner, or other volatile
chemicals may be present.
● Avoid locations that are subject to vibration.
● Connect only to a power outlet of the rated voltage
and power supply frequency (either 120 V, 60 Hz
or 220-240 V, 50/60 Hz, depending on your
region).
● Do not connect other electrical equipment to the
same power outlet to which the scanner is
connected. Also, when using an extension cord,
make sure that the extension cord is rated for the
current requirements of the scanner.
● Never try to disassemble the AC adapter or modify
it in any way, as this is extremely dangerous.
● The power cord and AC adapter may become
damaged if they are often stepped on or if heavy
objects are placed on them. Continued use of a
damaged power cord and AC adapter can lead to
an accident, such as a fire or electrical shock.
● Do not use the power cord while it is coiled.
3
● Do not pull directly on the power cord. When
disconnecting the power cord, grasp the plug and
remove it from the outlet.
● Keep the area around the power plug clear of
objects so that the power cord can be
disconnected easily in an emergency.
● Use only the AC adapter provided with this
scanner. Also, do not use the AC adapter provided
with the scanner with any other electrical devices.
Model: MG1-4558
● If you have any questions regarding the power
supply, contact your local authorized Canon dealer
or service representative for further information.
❏ Moving the Scanner
● When moving the scanner, always hold it with both
hands to avoid dropping it. The weight of the
scanner unit is approximately 7.9 lbs (3.6 kg).
● Before moving the scanner, make sure the
document tray is closed and the interface cable
and AC adapter are disconnected. If the scanner is
transported with these items connected, the plugs
and connectors may be damaged due to
excessive force applied to them during movement.
❏ Handling
WARNING
Note the following precautions whenever using the
scanner. Failure to do so may result in a fire or
electric shock.
■ Never use alcohol, benzene, paint thinner, aerosol
sprays, or any other highly flammable substance
near the scanner.
4
■ Do not cut, damage, or modify the power cord or
AC adapter. Do not place heavy objects on the
power cord or AC adapter, and do not pull or
excessively bend the power cord.
■ Never connect the power cord when your hands
are wet.
■ Do not connect the scanner to a multiplug power
strip.
■ Do not knot or coil the power cord, as this may
result in a fire or electric shock. When connecting
the power cord, make sure that the power plug is
securely and completely inserted into the power
outlet.
■ Do not use power cords and AC adapters other
than the power cord and AC adapter provided with
this scanner.
■ Never try to take the scanner apart or modify it in
any way.
■ Never try to take the AC adapter apart or modify it
in any way, as this is dangerous and may lead to a
fire or electric shock.
■ Do not use flammable aerosol sprays near the
scanner.
■ When cleaning the scanner, turn the power OFF
and disconnect the power cord from the power
supply.
■ Clean the scanner using a slightly dampened cloth
which has been well wrung out. Never use alcohol,
benzene, paint thinner, or any other flammable
substances.
■ If the scanner makes strange noises, or gives off,
smoke, heat, or strange odors, or the scanner
does not function or other abnormalities occur
when you use the machine, immediately turn the
power OFF, and disconnect the power plug from
the power outlet. Then, contact your local
authorized Canon dealer or service representative
for further information.
■ Do not drop the scanner, or subject it to impact or
strong shock. Should the scanner ever become
damaged, immediately turn the power OFF, and
disconnect the power plug from the power outlet.
Then, contact your local authorized Canon dealer
or service representative to have the unit serviced.
■ Before moving the scanner, make sure to turn the
power OFF, and disconnect the power plug from
the power outlet.
CAUTION
■ Do not install the scanner on a surface that is
unstable or tilted, or in an area subject to
excessive vibrations, as this may cause the
scanner to fall, resulting in personal injury or
damage to the scanner.
■ Do not block the ventilation openings. Doing so
could cause the scanner to overheat, creating a
risk of fire.
■ Never place small metal objects such as staples,
paper clips, or jewelry on the scanner. These items
may fall into the scanner, and cause a fire or
electric shock. Should such objects ever fall inside
the scanner, immediately turn the power OFF, and
disconnect the power plug from the power outlet.
Then, contact your local authorized Canon dealer
or service representative to have the unit serviced.
■ Do not install the scanner in a humid or dusty
location. Doing so may result in a fire or electric
shock.
■ Do not place objects on top of the scanner, as they
may tip over and fall, resulting in personal injury.
■ Do not use the scanner with a power supply
voltage other than 120/220-240 VAC. Doing so
might cause fire or electric shock.
■ When disconnecting the power cord, grasp it firmly
by its plug. Do not pull directly on the power cord,
as this may damage or expose the cord’s internal
wiring, resulting in a fire or electric shock.
■ Leave sufficient space around the power plug so
that it can be disconnected easily. If objects are
placed around the power plug, you will be unable
to disconnect it in an emergency.
■ Do not allow water or flammable substances
(alcohol, paint thinner, benzene, etc.) to spill into
the scanner, as this may result in a fire or electric
shock.
■ Turn OFF the power for safety when not using the
scanner for a long period of time, such as
overnight. Also, turn OFF the power, and
disconnect the AC adapter from the scanner and
disconnect the power cord from the power outlet
for safety when the machine will not be used for an
extended period of time, such as during
consecutive holidays.
■ Do not wear loose clothing or jewelry that may get
caught in the scanner while you are using it. This
may result in personal injury. Be extra careful of
neckties and long hair. If anything becomes caught
in the scanner, immediately disconnect the power
cord to stop the scanner.
■ Be careful when placing paper in the scanner and
when removing jammed paper. It is possible to cut
your hand on the edge of a sheet of paper.
5
❏ Disposal
● Prior to disposing of the scanner, initialize the
scanner to ensure that the registered data is
deleted.
● When disposing of the scanner, make sure to
follow all local ordinances and laws or consult with
the retailer who sold you the scanner.
6
ScanFront Setup Overview
Follow the procedures below to set up the ScanFront.
1. Checking the Supplied Accessories (See p. 8)
Confirm that all of the supplied accessories are included.
2. Removing the Packing Materials and Attaching
the Feed Roller (See p. 9)
Remove the packing materials protecting the scanner, and
attach the supplied feed roller. (See p. 9.)
3. Installing the Scanner and Connecting to a
Network (See p. 11)
Move the scanner to the desired installation site, and
connect the AC adaptor and network cable.
4. Turning the Power ON and OFF (See p. 12)
Use the power switch to turn the scanner ON, and press
[Power off] on the touch panel to turn it OFF.
5. Configuring the Scanner Settings (See p. 13)
To set up the scanner, configure the administrator settings
on the scanner and the Web Menu settings from your
computer’s Web browser. This guide describes how to
configure the network settings from the scanner, how to set
the date and time and confirm the time zone from the Web
Menu, and how to configure mail server settings for
sending e-mail.
For details on other settings, refer to the Operation Guide
and ScanFront 300/300P/330 INSTRUCTIONS
(electronic manual).
• Configuring the Date and Time and Confirming the
Time Zone
Set the date and time and confirm the time zone by
logging in to the Web Menu. (See p. 16.)
• Mail Server Settings
Configure the mail server to be used for sending e-mail.
(See p. 17.)
6. Scanning Procedure (See p. 18)
This section gives an overview of the procedure for
scanning a document, using the example of scanning from
the Home screen. For more details on this procedure, refer
to the Operation Guide and ScanFront 300/300P/330
INSTRUCTIONS (electronic manual).
7. Supplied Applications (See p. 21)
This section describes the applications (ScanFront Service
and ScanFront Administration Tool) that are included on
the supplied application disc.
* For a Web browser, use Microsoft Internet Explorer 6.0 or later
or Firefox 3.5 or later.
• Network Settings
From the [Administrator setting] screen on the scanner,
configure the [Device Name] and [IP Address] settings
needed to connect to the network. (See p. 14.)
7
1. Checking the Supplied Accessories
After unpacking the scanner, confirm that the following accessories are included. In the unlikely event that any of these accessories
are missing or damaged, contact your local authorized Canon dealer.
Setup and Operation Guide (this manual)
The printed version of Setup and Operation
Guide may vary depending on your region.
PDF files of the Setup and Operation Guide
in other languages can be found on the
application disc.
ScanFront
Application Disc**
The following manuals are stored as PDF
files on this disc:
• INSTURCTIONS
• Setup and Operation Guide
Feed Roller
The feed roller must be attached to the
scanner during installation. (See p. 9.)
AC Adapter*
(Cord length: 4.9 ft. (1.5 m))
Warranty Card
(U.S.A. and Canada only)
Power Cord*
(Cord length: 3.3 ft. (1 m))
Registration Card
(U.S.A. and Canada only)
0880281099-L5T1P7-BR01
The shape of the power plug varies by
country and region.
CANON CANADA INC.
6390 DIXIE RD
MISSISSAUGA
ON
L5T
9Z9
* Make sure to use only the supplied AC adapter and power cord.
** The PDF files stored on the disc require Adobe Acrobat or Adobe Reader to open. (You can download Adobe Reader from the Adobe Web site.)
8
2. Removing the Packing Materials and Attaching the Feed Roller
Remove all of the packing materials protecting the scanner, and attach the feed roller.
1. Remove the orange tape (3 pieces) securing the
outer case.
CAUTION
The open/close movement of the panel unit is linked to the up/
down movement of the document eject tray. Do not press on the
document eject tray when you open the panel unit.
2. Gently open the document eject tray.
4. Remove the orange tape (2 pieces) securing the
roller covers.
3. Pull the lock lever toward you and then fully open the
panel unit.
5. Open the roller cover for the feed roller.
Lock lever
9
6. Lift up the roller lock lever a, and slide it in the
direction of the arrow b.
7. Align the notch in the shaft of the roller with the shaft
of the scanner, and place the feed roller into position.
9. Lower the roller lock lever to lock the feed roller into
position.
10. Close the roller cover. Make sure you hear a click,
which indicates the cover has returned to its original
position.
8. Move the lock lever in the direction of the arrow, then
insert it into the hole in the feed roller.
11. Gently close the panel unit. Press on both sides of
the unit until you hear a click, which indicates the unit
is locked.
12. Gently close the document eject tray.
10
3. Installing the Scanner and Connecting to a Network
Before setting up the scanner, you need to move it to the installation site, and connect the AC adaptor and network cable.
IMPORTANT
For information on installation safety, see p. 3.
❏ Connecting the AC Adapter
Follow the procedure shown below to connect the AC adapter.
CAUTION
Make sure to use only the AC adapter and power cord included with the scanner.
The shape of the power plug
varies by country and region.
a Connect the power cord and AC adapter.
b Insert the plug of the AC adapter into the power connector.
c Connect the power cord to the wall outlet.
❏ Connecting the Network Cable
Insert the network cable connector (RJ-45) into the LAN port.
11
4. Turning the Power ON and OFF
Use the power switch to turn the scanner ON, and press the [Power off] button on the touch panel to turn it OFF.
❏ Turning the Power ON
❏ Turning the Power OFF
Press the power switch to turn the scanner ON. The power
indicator lights, and the Home screen or the login screen
appears.
Press the [Power off] button displayed at the bottom left of
the panel to turn the scanner OFF.
Power switch
Home screen
Power
indicator
IMPORTANT
IMPORTANT
• It takes approximately 40 seconds for the Home screen to
appear after the power switch is turned on.
• If users have been registered, the login screen appears.
(Refer to “Login screen” on p. 5-4 of the ScanFront 300/300P/
330 INSTRUCTIONS.)
• When the power indicator is lit but nothing appears on the
touch panel, Display Off has activated to turn the panel display
off. You can touch the panel to restore the display. (Refer to
“Display Off” on p. 6-31 of the ScanFront 300/300P/330
INSTRUCTIONS.)
• When the power indicator is flashing but nothing appears on
the touch panel, the Low Power mode has activated to
temporarily stop scanner operations. To switch out of Low
Power mode, press the power switch or touch the touch panel.
(Refer to “Low Power Mode” on p.6-31 of the ScanFront 300/
300P/330 INSTRUCTIONS.)
12
• When restarting the scanner, wait at least 5 seconds after
turning the power OFF before turning it ON again.
• If the scanner stops responding, press and hold the power
switch to shut down the system, and then press the power
switch to turn the scanner ON again. In such cases, settings
configured immediately before shutting down may be lost.
5. Configuring the Scanner Settings
To set up the scanner, you must configure the [Network setting] items under [Administrator setting] on the scanner unit, and
configure settings on the Web Menu (Administrator Mode).
This section describes the network settings configured under [Administrator setting] on the scanner (see p. 14), and date/time
configuration and time zone confirmation in the Web Menu (Administrator Mode) (see p. 16), and mail server settings for sending
images via e-mail (see p. 17).
For details on other settings, refer to the ScanFront 300/300P/330 INSTRUCTIONS (electronic manual).
The following items are only a few of the availavle settings. The necessary configuration differs, depending on the scale of the
network environment in which you plan to use the scanner. To use the scanner with the minimum required settings, you must
register addresses to the Shared Address Book in addition to configuring the [Network setting] items.
Setting Item
Description
Administrator setting
Web Menu
(Administrator Mode)
Network setting
Set the Device Name and IP Address.
Yes
No
Administrator password
Set the password required to login to
[Administrator setting] and the Web Menu.
Yes
Yes
Login type
Select the screen that appears when users log in.
Yes
Yes
Register user
Register the users who will use the ScanFront.
No
Yes
Register Shared Address
Book
Register entries in the Shared Address Book
available to all users.
No
Yes
Register Shared Job Button
Register the Shared Job Button available to all
users.
No
Yes
Device Configuration
Set the basic operations of the ScanFront
(including network settings).
No
Yes
E-mail server settings
Register the SMTP server to be used for sending email.
No
Yes
Authentication server settings
Register a domain server that can search users with
Active Directory.
No
Yes
Address book server settings
Register an LDAP server that can search e-mail
address books.
No
Yes
13
❏ Network Settings
Follow the procedure below to confirm and configure the
device name and IP address needed to connect the scanner to
a network.
2. Press [OK] to display the [Administrator setting]
screen.
No administrator password is set by default.
IMPORTANT
• The device name is the name used to identify the scanner on
the network and is set to the 14 alphanumeric characters of
the SF+MAC address by default. When changing this setting,
make sure to select a unique name that is different from those
of all other devices.
• Under default settings, the IP address is assigned
automatically by the DHCP server. When a DHCP server is
not used, clear the [DHCP server Enable] check box, and
enter a fixed address. For details, contact your network
administrator.
• The device name or IP address is used as the URL when
accessing the Web Menu. Be sure to write down both the
device name and IP address in case you forget them.
1. Press [Administrator setting].
The [Administrator Password] input box appears.
14
3. Press [Network setting].
4. Confirm the [Device name] and [IP address].
Press [Shift] to switch, the entry screen to capital letters.
6. Enter the new device name (or IP address), and
press [OK].
IMPORTANT
• The device name is the name used to identify the scanner on
the network. When changing this setting, make sure to select
a unique name that is different from those of all other devices.
• The device name can be a combination of letters (A-Z, a-z),
numbers (0-9), and hyphens (-) up to 15 characters long.
• The device name must begin with a letter. You cannot end the
device name with a hyphen.
7. Confirm the new device name and IP address, and
5. Press [Device name] (or [IP address]).
press [OK].
A keyboard entry screen appears.
8. Press [Close] to return to the Home screen.
9. Press [Power off] to restart the scanner.
15
❏ Configuring the Date and Time and
Confirming the Time Zone
When you finish configuring the network settings, log in to
the Web Menu to set the date and time and confirm the time
zone.
For details on other settings, refer to the Operation Guide and
ScanFront 300/300P/330 INSTRUCTIONS (electronic
manual).
IMPORTANT
Make sure that the time zone is set to your region of use. If the
time zone is set to the wrong region, the recorded sending times
and time stamps for image files will not match the time setting
displayed on the scanner.
1. Turn the scanner ON.
5. Click [Login] to log in to the Web Menu (Administrator
Mode).
Hint
No administrator password is set by default. If you set a
password under the administrator settings, enter the password
to log in. (See p. 13.)
2. Log in to [Administrator setting], open the network
settings, and confirm the IP address. (See “Network
Settings” on p. 14.)
3. Launch the Web browser on the computer.
4. Enter the device name or the IP address as the URL
to open the Web Menu.
Ex.) http://scanfront when the device name is ScanFront, and
http://172.19.xxx.xxx for the IP address.
6. Click [Device Configuration].
The [Device Configuration] screen appears.
Hint
If the Web Menu does not appear in the desired language,
select the desired language in the [Language] box to switch the
Web Menu display.
16
7. Check the [Language/Timezone] setting.
IMPORTANT
• If the correct time zone is not set, the time stamps that are
saved for the send time of e-mail messages, and for the saved
image files will be incorrect.
• When [Enable daylight saving time] is selected, the correct
time may not be reflected. In this case, set the correct time.
❏ Mail Server Settings
To send scanned images via e-mail, open the Server
Settings screen from the Web Menu and register a mail
server. For details, refer to “Server Settings” on p. 6-33 of
the ScanFront 300/300P/330 INSTRUCTIONS (electronic
manual).
Hint
To change the setting, click [Language/Timezone] or [Setting].
Language/Timezone Setting Screen
17
6. Scanning Procedure
This section gives an overview of the procedure for sending scanned images from the Home screen.
For more details, refer to the Operation Guide or the ScanFront 300/300P/330 INSTRUCTIONS (electronic manual).
1. Place a document in the scanner.
2. Select a transfer destination by pressing a
destination button.
Hint
• You can change the transfer destination by changing the
[Address type].
• The following icons are used to indicate the types of address.
:E-mail
:Shared folder
:Fax
:FTP
:Group
• Pressing an address adds a checkmark (
) to the icon and
selects the address. Pressing a selected address again clears
the selection.
• Each time you press an e-mail or group icon, the send
condition changes (To, Cc, Bcc).
:To
:Cc
:Bcc
:Selection cleared
IMPORTANT
If an address has a shaded background but no check mark, it is
not selected.
The [Address selection] screen appears.
4. If there are no addresses registered in the address
book, press [Edit] to register addresses.
Hint
You can change the transfer destination from the [Address
selection] screen.
3. Press one of the displayed addresses to select it.
Hint
If the address you want to register is for your private use,
register it in My Address Book. For details, refer to “Registering
and Editing Addresses” on p. 3-23 of the Operation Guide.
18
5. Confirm that the selected address has a check mark,
and press [Next].
The [Scan / Delivery Options] screen appears.
6. Confirm the scan settings, and press [Start].
• Press [Abort] to cancel the scanned images and return to
the Scan/Delivery Options screen.
• Press the [Continue] button to resume scanning.
• Press [Complete] to go to the Send screen.
7. Press [Continue].
8. Check the scanned image.
Scanning starts, and stops when the document has been
scanned.
: Display the image of the next page.
: Display the image of the previous page.
: Move the viewing area around an image
when an enlarged view of the image is shown.
: Rotate the image 90 degrees counterclockwise.
: Rotate the image 90 degrees clockwise.
: Enlarge the image.
: Reduce the image.
19
Hint
When the preview image is enlarged, you can drag your finger
on the image to scroll.
10. Confirm the address and press [OK] to send the
scanned image.
The scanner sends the image file and returns to the Home
screen.
Hint
The screen that appears after images are sent can be selected
in the settings. For details, refer to the Operation Guide.
9. Press [Send].
An address confirmation message appears.
20
7. Supplied Applications
The following applications are included on the supplied application disc.
❏ ScanFront Service
ScanFront Service is software that supplements the
network functions of the ScanFront. By installing the
software onto a computer on the same network as the
ScanFront, you can send scanned images from the
ScanFront to devices for which direct transfer would be
otherwise disabled (printers, computers on a different
segment, etc.).
Double-click the installer located in the following folder
on the application disc to install the software.
Q:\ScanFrontService\setup.exe
(“Q” is the letter assignment for the disc drive)
For details on operations, refer to the separate ScanFront
300/300P/330 INSTRUCTIONS (electronic manual).
❏ ScanFront Administration Tool
ScanFront Administration Tool is software that allows you
to manage multiple ScanFront scanners at one time. This
software allows you to perform operations such as
checking the current status of the ScanFront scanners on
the network, configuring ScanFront settings, managing
users, and backing up and restoring configuration data.
To use the software, install it on a computer connected to
the same network as the ScanFront scanners. Double-click
the installer in the following folder on the application disc
to install the software.
Q: \AdministrationTool\setup.exe (“Q” is the letter
assignment for the disc drive)
For details on operations, refer to the separate ScanFront
300/300P/330 INSTRUCTIONS (electronic manual).
21
22
ScanFront 330
Operation Guide
Please read this manual before using the scanner.
After you finish reading this manual, keep it in a safe place
for future reference.
International ENERGY STAR® Office Equipment
Program
As an ENERGY STAR® Partner, Canon
Electronics Inc. has determined that this
machine meets the ENERGY STAR® Program
guidelines for energy efficiency.
The International ENERGY STAR® Office
Equipment Program is an international program that promotes
energy saving through the use of computers and other office
equipment.
The program backs the development and dissemination of
products with functions that effectively reduce energy
consumption. It is an open system in which business
proprietors can participate voluntarily. The targeted products
are office equipment, such as computers, monitors, printers,
fax, machine, copiers, and scanners. The standards and logos
are uniform among participating nations.
This model doesn’t provide “setting options” for power
management.
Under factory default settings, the scanner will enter Low
Power mode after 12 minutes of inactivity. Although you can
change the period of time before the scanner enters Low
Power mode to up to 230 minutes, we recommend using the
default setting.
FCC REGULATIONS (For 120 V model)
Network Scanner, Model M11-1041/M11-1051/M11-1053
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician
for help.
Use of shielded cable is required to comply with class B limits
in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment
unless otherwise specified in the manual. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
Canon U.S.A. Inc.
One Canon Park, Melville, NY 11747, U.S.A.
Tel. No. (800)652-2666
RADIO INTERFERENCE REGULATIONS (For 120 V
models)
This digital apparatus does not exceed the Class B limits for
radio noise emissions from digital apparatus as set out in the
Interference-causing equipment standard entitled “Digital
Apparatus”, ICES-003 of the Industry Canada.
RÈGLEMENT SUR LE BROUILLAGE
RADIOÉLECTRIQUE (For 120 V models)
Cet appareil numérique respecte les limites de bruits
radioélectriques applicables aux appareils numériques de
Classe B prescrites dans la norme sur le matériel brouilleur:
“Appareils Numériques”, NMB-003 édictée par l’Industrie
Canada.
For CA, USA Only
Included battery contains Perchlorate Material - special
handling may apply.
See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/ for
detail.
European Union (and EEA) only
This symbol indicates that this product is not to be
disposed of with your household waste, according
to the WEEE Directive (2002/96/EC) and your
national law. This product should be handed over
to a designated collection point, e.g., on an
authorized one-for-one basis when you buy a new similar
product or to an authorized collection site for recycling waste
electrical and electronic equipment (EEE). Improper handling
of this type of waste could have a possible negative impact on
the environment and human health due to potentially
hazardous substances that are generally associated with EEE.
At the same time, your cooperation in the correct disposal of
this product will contribute to the effective usage of natural
resources. For more information about where you can drop off
your waste equipment for recycling, please contact your local
city office, waste authority, approved WEEE scheme or your
household waste disposal service. For more information
regarding return and recycling of WEEE products, please visit
www.canon-europe.com/environment.
(EEA: Norway, Iceland and Liechtenstein)
Model Names
The following names may be provided for the safety
regulations in each sales region of the Network Scanner.
ScanFront 330: Model M11-1053
Trademarks
• Canon and the Canon logo are registered trademarks of
Canon Inc. in the United States and may also be trademarks
or registered trademarks in other countries.
• imageFORMULA is a trademark of Canon Electronics Inc.
• Microsoft, Windows, Internet Explorer, and Active
Directory are registered trademarks or trademarks of
Microsoft Corporation in the United States and other
countries.
• Adobe, Acrobat, and Adobe Reader are registered
trademarks or trademarks of Adobe Systems Incorporated in
the United States and other countries.
• Other product and company names herein may be the
trademarks of their respective owners.
Disclaimers
The information in this document is subject to change without
notice.
CANON ELECTRONICS INC. MAKES NO WARRANTY
OF ANY KIND WITH REGARD TO THIS MATERIAL,
EITHER EXPRESS OR IMPLIED, EXPECT AS
PROVIDED HEREIN, INCLUDING WITHOUT
LIMITATION, THEREOF, WARRANTIES AS TO
MARKETABILITY, MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE OF USE OR NONINFRINGEMENT. CANON ELECTRONICS INC. SHALL
NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY NATURE, OR
LOSSES OR EXPENSES RESULTING FROM THE USE
OF THIS MATERIAL.
CANON ELECTRONICS INC. IS NOT LIABLE FOR THE
STORAGE AND HANDLING OF DOCUMENTS
SCANNED WITH THIS PRODUCT, OR THE STORAGE
AND HANDLING OF RESULTING SCANNED IMAGE
DATA.
IF YOU INTEND TO DISCARD THE ORIGINALS OF
SCANNED DOCUMENTS, YOU THE CUSTOMER ARE
RESPONSIBLE FOR INSPECTING THE SCANNED
IMAGES AND VERIFYING THAT DATA IS INTACT.
THE MAXIMUM LIABILITY OF CANON
ELECTRONICS INC. UNDER THIS WARRANTY IS
LIMITED TO THE PURCHASE PRICE OF THE
PRODUCT COVERED BY THE WARRANTY.
Copyright
libtiff
Copyright (c) 1988-1996 Sam Leffler
Copyright (c) 1991-1996 Silicon Graphics, Inc.
Permission to use, copy, modify, distribute, and sell this
software and its documentation for any purpose is hereby
granted without fee, provided that (i) the above copyright
notices and this permission notice appear in all copies of the
software and related documentation, and (ii) the names of
Sam Leffler and Silicon Graphics may not be used in any
advertising or publicity relating to the software without the
specific, prior written permission of Sam Leffler and Silicon
Graphics.
THE SOFTWARE IS PROVIDED “AS-IS” AND
WITHOUT WARRANTY OF ANY KIND, EXPRESS,
IMPLIED OR OTHERWISE, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.
IN NO EVENT SHALL SAM LEFFLER OR SILICON
GRAPHICS BE LIABLE FOR ANY SPECIAL,
INCIDENTAL, INDIRECT OR CONSEQUENTIAL
DAMAGES OF ANY KIND, OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE,
DATA OR PROFITS, WHETHER OR NOT ADVISED OF
THE POSSIBILITY OF DAMAGE, AND ON ANY
THEORY OF LIABILITY, ARISING OUT OF OR IN
CONNECTION WITH THE USE OR PERFORMANCE OF
THIS SOFTWARE.
libjpeg
Portions of this software are based in part on the work of the
Independent JPEG Group.
MD5
derived from the RSA Data Security, Inc. MD5 MessageDigest Algorithm
Copyright (c) 1998 - 2002, Paul Johnston & Contributors
All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
Neither the name of the author nor the names of its
contributors may be used to endorse or promote products
derived from this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT
HOLDERS AND CONTRIBUTORS “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
Copyright (c) 1991-2, RSA Data Security, Inc. Created 1991.
All rights reserved.
License to copy and use this software is granted provided that
it is identified as the “RSA Data Security, Inc. MD5 MessageDigest Algorithm” in all material mentioning or referencing
this software or this function.
License is also granted to make and use derivative works
provided that such works are identified as “derived from the
RSA Data Security, Inc. MD5 Message-Digest Algorithm” in
all material mentioning or referencing the derived work.
RSA Data Security, Inc. makes no representations concerning
either the merchantability of this software or the suitability of
this software for any particular purpose. It is provided “as is”
without express or implied warranty of any kind.
These notices must be retained in any copies of any part of
this documentation and/or software.
II. The required acknowledgements for third party
components included in the OperaRBrowser engine
are as follows:
Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN
MERCURY AND MUST BE RECYCLED OR DISPOSED
OF ACCORDING TO LOCAL, STATE OR FEDERAL
LAWS.
THIS SOFTWARE IS BEING PROVIDED "AS IS",
WITHOUT ANY EXPRESS OR IMPLIED
WARRANTY.IN PARTICULAR, NEITHER THE
AUTHOR NOR LUCENT MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND
CONCERNING THE MERCHANTABILITY
OF THIS SOFTWARE OR ITS FITNESS FOR ANY
PARTICULAR PURPOSE.
Opera® or Opera Software™ are registered trademarks of
Opera Software ASA in Norway or other countries.
OPERA SOFTWARE ASA'S AND THIRD PARTY
SUPPLIER'S COPYRIGHT NOTICE AND
ACKNOWLEDGEMENTS
I. Opera Software ASAs browser/browser engine
Opera®Browser from Opera Software ASA. Copyright 19952008 Opera Software ASA. All rights reserved.
This software is being provided on an « as is »‚ basis. Opera
and its suppliers disclaim all warranties regarding the
software, either express or implied, statutory or otherwise,
including without limitation warranties of functionality,
fitness for a particular purpose or non-infringement.
1. David Gay's binary/decimal conversion code (dtoa
and strtod)
"The author of this software is David M. Gay.
Copyright (c) 1991, 2000, 2001 by Lucent Technologies.
Permission to use, copy, modify, and distribute this software
for any purpose without fee is hereby granted, provided that
this entire notice is included in all copies of any software
which is or includes a copy or modification of this software
and in all copies of the supporting documentation for such
software.
2. OpenSSL 0.9.8e (formerly SSLeay)
The OpenSSL toolkit stays under a dual license, i.e. both the
conditions of the OpenSSL License and the original SSLeay
license apply to the toolkit. See below for the actual license
texts. Actually both licenses are BSD-style Open Source
licenses. In case of any license issues related to OpenSSL
please contact openssl-core@openssl.org.
OpenSSL License
Copyright (c) 1998-2008 The OpenSSL Project. All rights
reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
3. All advertising materials mentioning features or use of this
software must display the following acknowledgment:
"This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/)"
4. The names "OpenSSL Toolkit" and "OpenSSL Project"
must not be used to endorse or promote products derived
from this software without prior written permission. For
written permission, please contact opensslcore@openssl.org.
5. Products derived from this software may not be called
"OpenSSL" nor may "OpenSSL" appear in their names
without prior written permission of the OpenSSL Project.
6. Redistributions of any form whatsoever must retain the
following acknowledgment:
"This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit
(http://www.openssl.org/)"
THIS SOFTWARE IS PROVIDED BY THE OpenSSL
PROJECT ``AS IS'' AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE OpenSSL
PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT
OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric
Young (eay@cryptsoft.com). This product includes software
written by Tim Hudson (tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com)
All rights reserved.
This package is an SSL implementation written by Eric
Young (eay@cryptsoft.com).
The implementation was written so as to conform with
Netscapes SSL.
This library is free for commercial and non-commercial use as
long as the following conditions are aheared to. The following
conditions apply to all code found in this distribution, be it the
RC4, RSA, lhash, DES, etc., code; not just the SSL code. The
SSL documentation included with this distribution is covered
by the same copyright terms except that the holder is Tim
Hudson (tjh@cryptsoft.com).
Copyright remains Eric Young's, and as such any Copyright
notices in the code are not to be removed.
If this package is used in a product, Eric Young should be
given attribution as the author of the parts of the library used.
This can be in the form of a textual message at program
startup or in documentation (online or textual) provided with
the package.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the copyright
notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above
copyright notice, this list of conditions and the following
disclaimer in the documentation and/or other materials
provided with the distribution.
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS
SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
The licence and distribution terms for any publically available
version or derivative of this code cannot be changed. i.e. this
code cannot simply be copied and put under another
distribution licence [including the GNU Public Licence.]
3. All advertising materials mentioning features or use of this
software must display the following acknowledgement:
"This product includes cryptographic software written by
Eric Young (eay@cryptsoft.com)"
The word 'cryptographic' can be left out if the rouines [SIC]
from the library being used are not cryptographic related
:-).
4. If you include any Windows specific code (or a derivative
thereof) from the apps directory (application code) you
must include an acknowledgement:
"This product includes software written by Tim Hudson
(tjh@cryptsoft.com)"
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS
IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
Copyright 2013 by CANON ELECTRONICS INC. All rights
reserved.
No part of this publication may be reproduced or transmitted
in any form or by any means, electronic or mechanical,
including photocopying and recording, or by any information
storage or retrieval system without the prior written
permission of CANON ELECTRONICS INC.
Introduction
Thank you for purchasing the Canon imageFORMULA ScanFront 330 network scanner.
Please read this manual thoroughly before using the scanner to familiarize yourself with its capabilities, and to make the most of its
many functions. After reading this manual, store it in a safe place for future reference.
About ScanFront 330
The ScanFront 330 is a network scanner that you can use without connecting to a computer.
You can transfer the data of an image scanned with the ScanFront 330 to a shared folder on a server PC or client PC on the network
or to an FTP server*, send it to a printer for printing**, or deliver it to a remote location via e-mail or Internet fax service. When
using the scanner without a network environment, you can also save the image files to USB memory.
* To send image files to a shared folder on a computer on a different segment of the network, the supplied ScanFront Service software must be
installed on a computer on the network.
** To send image files to a printer, the supplied ScanFront Service software must be installed on a computer on the network.
Shared Folder
(Server PC, Client PC)
Network
Printer
Save File
Save File
Send E-mail
Mail Server
Internet Fax Service
FTP Server
ScanFront
USB Memory
Conceptual Diagram of the ScanFront
i
❏ Manuals for the Scanner
The following manuals are provided with the Canon
ScanFront 330. Be sure to read these manuals thoroughly
before using the scanner.
Setup and Operation Guide (This Manual)*
Setup Guide
Describes the procedure for setting up the scanner for
scanning. Set up the ScanFront in accordance with the
Setup Guide. For details on the ScanFront, refer to the
Operation Guide and ScanFront 300/300P/330
INSTRUCTIONS (electronic manuals).
Operation Guide
Provides an overview of the functions of the scanner, and
describes the basic operations for using the ScanFront. For
details on the settings of the ScanFront, refer to the
ScanFront 300/300P/330 INSTRUCTIONS (electronic
manual).
* The printed version of Setup and Operation Guide may vary
depending on your region. PDF files of the Setup and Operation
Guide in other languages can be found on the application disc.
INSTRUCTIONS: Electronic Manual
Describes how to use the scanner, and includes
instructions for configuring the scanner settings, as well as
handling, maintenance, and troubleshooting information.
This manual is stored as a PDF file on the supplied
application disc and requires Adobe Reader to open. (You
can download Adobe Reader from the Adobe Web site.)
❏ Symbols Used in This Manual
The following symbols are used in this manual to explain
procedures, restrictions, handling precautions, and
instructions that should be observed for safety.
WARNING
Indicates a warning concerning operations that may lead to
death or injury to persons if not performed correctly. To
use the scanner safely, always pay attention to these
warnings.
CAUTION
Indicates a caution concerning operations that may lead to
injury to persons, or damage to property if not performed
correctly. To use the scanner safely, always pay attention
to these cautions.
IMPORTANT
Indicates operational requirements and restrictions. Be
sure to read these items carefully to operate the scanner
correctly, and avoid damage to the scanner.
Hint
Indicates a clarification of an operation, or contains
additional explanations for a procedure. Reading these
notes is highly recommended.
ii
❏ How This Manual is Organized
This manual consists of the following chapters.
Chapter 1 Before Use
This chapter provides an overview of the ScanFront.
Chapter 2 Handling
This chapter describes the types of documents that can be
scanned, and the basic operations of the scanner.
Chapter 3 Operating Procedures
This chapter describes the basic operating procedures for
the scanner.
Chapter 4 Web Menu (User Mode)
This chapter describes the Web menu for the user to
configure settings.
Chapter 5 Troubleshooting
This chapter describes how to respond when problems
occur or warning messages appear.
Chapter 6 Index
iii
❏ Table of Contents
Introduction............................................................... i
Manuals for the Scanner ..........................................ii
Symbols Used in This Manual .................................. ii
How This Manual is Organized................................ iii
Chapter 1 Before Use
1. Important Safety Instructions............................1-2
Installation Location.............................................. 1-2
Power ................................................................... 1-2
Moving the Scanner.............................................. 1-3
Handling ............................................................... 1-3
Disposal................................................................ 1-5
Chapter 3 Operating Procedures
1. Flow of Scanner Operations.............................3-2
2. Turning the Power ON and OFF ......................3-3
Turning the Power ON.......................................... 3-3
Turning the Power OFF ........................................ 3-3
3. Login Screen .................................................... 3-4
Login Screen Types.............................................. 3-4
When Using Server Authentication....................... 3-4
List Type Login ..................................................... 3-5
Key in Type Login................................................. 3-6
4. Screen Displayed after Login ........................... 3-7
Home Screen........................................................ 3-7
Job Button Screen ................................................ 3-7
2. Names and Functions of Parts .........................1-6
5. User Settings Screen .......................................3-8
Front and Document Feed and Eject Trays.......... 1-6
Side and Rear....................................................... 1-7
6. Scanning Procedures .......................................3-9
Change Password ................................................ 3-8
Plain Paper ........................................................... 2-2
Business Card ...................................................... 2-2
Card...................................................................... 2-3
Scanning From the Home Screen ........................ 3-9
Scanning From the Job Button Screen............... 3-10
Address Selection Screen .................................. 3-11
USB Memory Screen.......................................... 3-13
Print Settings Screen.......................................... 3-14
Scanning............................................................. 3-15
2. Preparing the Scanner......................................2-4
7. Registering and Editing Addresses ................ 3-19
Preparing the Document Feed Tray and
Eject Tray ............................................................. 2-4
Feed Selection Lever............................................ 2-5
USB Port............................................................... 2-5
Registering a New Address ................................ 3-19
Modifying an Address ......................................... 3-22
Copying an Address ........................................... 3-22
Chapter 2 Handling
1. Documents .......................................................2-2
3. Placing Documents...........................................2-6
Placing a
Placing a
Placing a
Placing a
Document ............................................. 2-6
Folded Document ................................. 2-7
Long Document .................................... 2-7
Card ...................................................... 2-8
8. Scan/Delivery Options.................................... 3-24
Scan Settings ..................................................... 3-25
File Formats........................................................ 3-29
Security Settings for PDF Files........................... 3-30
Delivery Options ................................................. 3-31
4. Clearing a Paper Jam or Double Feed Error ....2-9
iv
Chapter 4 Web Menu (User Mode)
1. Web Menu Overview ........................................ 4-2
2. Logging In to the Web Menu ............................ 4-3
3. User Settings.................................................... 4-4
User Settings ........................................................ 4-5
4. Address Book Settings ..................................... 4-9
Registering New Addresses ............................... 4-11
Copying Addresses ............................................ 4-14
Exporting and Importing Address Books ............ 4-14
5. Job Button Settings ........................................ 4-16
Registering New Job Buttons ............................. 4-18
Scan Settings Overview ..................................... 4-19
Copying Job Buttons .......................................... 4-23
Editing Jobs ........................................................ 4-24
Exporting and Importing Job Buttons ................. 4-24
Chapter 5 Troubleshooting
1. Troubleshooting ............................................... 5-2
Chapter 6 Index
1. Index ................................................................ 6-2
v
Chapter 1 Before Use
1. Important Safety Instructions ........................... 1-2
Installation Location ..............................................1-2
Power ....................................................................1-2
Moving the Scanner ..............................................1-3
Handling ................................................................1-3
Disposal ................................................................1-5
2. Names and Functions of Parts......................... 1-6
Front and Document Feed and Eject Trays ..........1-6
Side and Rear .......................................................1-7
1. Important Safety Instructions
To ensure the safe operation of this scanner, be sure to read the safety warnings and precautions described below.
❏ Installation Location
The performance of this scanner is affected by the
environment in which it is installed. Make sure that the
location where the scanner is installed meets the following
environmental requirements.
● Provide adequate space around the scanner for
operation, maintenance, and ventilation.
At least
15.75"
(40 cm)
❏ Power
At least
23.62" (60 cm)
● Avoid installing the machine in direct sunlight. If
this is unavoidable, use curtains to shade the
scanner.
● Avoid locations where a considerable amount of
dust accumulates.
● Avoid warm or humid locations, such as in the
vicinity of a water faucet, water heater, or
humidifier, and avoid locations where the fumes
from ammonia, paint thinner, or other volatile
chemicals may be present.
● Avoid locations that are subject to vibration.
1-2
● Avoid exposing the scanner to rapid changes in
temperature. If the room in which the scanner is
installed is cold but rapidly heated, water droplets
(condensation) may form inside the scanner. This
may result in a noticeable degradation in scanning
quality.
The following conditions are recommended for
optimal scanning quality:
Room temperature: 10 °C to 32.5 °C (50 °F to
90.5 °F)
Humidity: 20% to 80% RH
● Avoid installing the scanner near equipment that
generates a magnetic field (e.g. speakers,
televisions, or radios).
● Connect only to a power outlet of the rated voltage
and power supply frequency (either 120 V, 60 Hz
or 220-240 V, 50/60 Hz, depending on your
region).
● Do not connect other electrical equipment to the
same power outlet to which the scanner is
connected. Also, when using an extension cord,
make sure that the extension cord is rated for the
current requirements of the scanner.
● Never try to disassemble the AC adapter or modify
it in any way, as this is extremely dangerous.
● The power cord and AC adapter may become
damaged if they are often stepped on or if heavy
objects are placed on them. Continued use of a
damaged power cord and AC adapter can lead to
an accident, such as a fire or electrical shock.
● Do not use the power cord while it is coiled.
❏ Moving the Scanner
● When moving the scanner, always hold it with both
hands to avoid dropping it. The weight of the
scanner unit is approximately 7.9 lbs (3.6 kg).
● Before moving the scanner, make sure the
document tray is closed and the interface cable
and AC adapter are disconnected. If the scanner is
transported with these items connected, the plugs
and connectors may be damaged due to
excessive force applied to them during movement.
❏ Handling
WARNING
Note the following precautions whenever using the
scanner. Failure to do so may result in a fire or
electric shock.
■ Never use alcohol, benzene, paint thinner, aerosol
sprays, or any other highly flammable substance
near the scanner.
■ Do not cut, damage, or modify the power cord or
AC adapter. Do not place heavy objects on the
power cord or AC adapter, and do not pull or
excessively bend the power cord.
■ Never connect the power cord when your hands
are wet.
■ Do not connect the scanner to a multiplug power
strip.
■ Do not knot or coil the power cord, as this may
result in a fire or electric shock. When connecting
the power cord, make sure that the power plug is
securely and completely inserted into the power
outlet.
■ Do not use power cords and AC adapters other
than the power cord and AC adapter provided with
this scanner.
■ Never try to take the scanner apart or modify it in
any way.
■ Never try to take the AC adapter apart or modify it
in any way, as this is dangerous and may lead to a
fire or electric shock.
■ Do not use flammable aerosol sprays near the
scanner.
■ When cleaning the scanner, turn the power OFF
and disconnect the power cord from the power
supply.
■ Clean the scanner using a slightly dampened cloth
which has been well wrung out. Never use alcohol,
benzene, paint thinner, or any other flammable
substances.
1-3
1
Before Use
● Do not pull directly on the power cord. When
disconnecting the power cord, grasp the plug and
remove it from the outlet.
● Keep the area around the power plug clear of
objects so that the power cord can be
disconnected easily in an emergency.
● Use only the AC adapter provided with this
scanner. Also, do not use the AC adapter provided
with the scanner with any other electrical devices.
Model: MG1-4558
● If you have any questions regarding the power
supply, contact your local authorized Canon dealer
or service representative for further information.
■ If the scanner makes strange noises, or gives off,
smoke, heat, or strange odors, or the scanner
does not function or other abnormalities occur
when you use the machine, immediately turn the
power OFF, and disconnect the power plug from
the power outlet. Then, contact your local
authorized Canon dealer or service representative
for further information.
■ Do not drop the scanner, or subject it to impact or
strong shock. Should the scanner ever become
damaged, immediately turn the power OFF, and
disconnect the power plug from the power outlet.
Then, contact your local authorized Canon dealer
or service representative to have the unit serviced.
■ Before moving the scanner, make sure to turn the
power OFF, and disconnect the power plug from
the power outlet.
CAUTION
■ Do not install the scanner on a surface that is
unstable or tilted, or in an area subject to
excessive vibrations, as this may cause the
scanner to fall, resulting in personal injury or
damage to the scanner.
■ Do not block the ventilation openings. Doing so
could cause the scanner to overheat, creating a
risk of fire.
■ Never place small metal objects such as staples,
paper clips, or jewelry on the scanner. These items
may fall into the scanner, and cause a fire or
electric shock. Should such objects ever fall inside
the scanner, immediately turn the power OFF, and
disconnect the power plug from the power outlet.
Then, contact your local authorized Canon dealer
or service representative to have the unit serviced.
1-4
■ Do not install the scanner in a humid or dusty
location. Doing so may result in a fire or electric
shock.
■ Do not place objects on top of the scanner, as they
may tip over and fall, resulting in personal injury.
■ Do not use the scanner with a power supply
voltage other than 120/220-240 VAC. Doing so
might cause fire or electric shock.
■ When disconnecting the power cord, grasp it firmly
by its plug. Do not pull directly on the power cord,
as this may damage or expose the cord’s internal
wiring, resulting in a fire or electric shock.
■ Leave sufficient space around the power plug so
that it can be disconnected easily. If objects are
placed around the power plug, you will be unable
to disconnect it in an emergency.
■ Do not allow water or flammable substances
(alcohol, paint thinner, benzene, etc.) to spill into
the scanner, as this may result in a fire or electric
shock.
■ Turn OFF the power for safety when not using the
scanner for a long period of time, such as
overnight. Also, turn OFF the power, and
disconnect the AC adapter from the scanner and
disconnect the power cord from the power outlet
for safety when the machine will not be used for an
extended period of time, such as during
consecutive holidays.
■ Do not wear loose clothing or jewelry that may get
caught in the scanner while you are using it. This
may result in personal injury. Be extra careful of
neckties and long hair. If anything becomes caught
in the scanner, immediately disconnect the power
cord to stop the scanner.
■ Be careful when placing paper in the scanner and
when removing jammed paper. It is possible to cut
your hand on the edge of a sheet of paper.
❏ Disposal
● Prior to disposing of the scanner, initialize the
scanner to ensure that the registered data is
deleted.
● When disposing of the scanner, make sure to
follow all local ordinances and laws or consult with
the retailer who sold you the scanner.
1
Before Use
1-5
2. Names and Functions of Parts
The names and functions of the parts of the ScanFront are shown below.
❏ Front and Document Feed and Eject Trays
e Lock Lever
Locks the panel unit. Pull the lever toward you to unlock
the panel unit. (See p. 2-10.)
f Document Guides
Adjust these to match the width of the document. (See
p. 2-6.)
g Document Feed Tray
Place documents here. (See p. 2-4.)
h USB Port (Front)
Connect a USB1.1/Hi-Speed USB2.0 compatible USB
memory device, USB keyboard, or USB mouse.
i Power Switch
Use this to turn the power ON. (See p. 3-3.)
* Use the Power OFF button on the touch panel to turn the
power OFF.
a Tray Extension
Open this to prevent scanned documents from slipping off.
b Document Eject Tray
Open this tray when using the ScanFront. If scanned
documents curl in the document eject tray, remove the
entire tray. (See p. 2-4.)
c Panel Unit
Open this when there is a paper jam or to perform
maintenance. (See p. 2-10.)
d Touch Panel
Touch this screen to operate the ScanFront.
1-6
j Feed Selection Lever
Use this lever to change the feed method for documents.
(See p. 2-5.)
k Power Indicator
Lights when the power is ON. (See p. 3-3.)
❏ Side and Rear
1
Before Use
l USB Port (Rear Left)
Connect a USB1.1/Hi-Speed USB2.0 compatible USB
memory device, USB keyboard, or USB mouse.
m Power Connector (24 VDC)
Connect the plug of the supplied AC adapter.
n Kensington Slot
This is an anti-theft slot that enables a key chain or lock to
be connected to prevent theft.
o Service Switch
This is a service switch. Do not insert any object into this
hole.
p LAN Port (RJ-45)
Connect an RJ-45 (10Base-T/100Base-TX) compatible
network cable.
q USB Ports (Rear Right)
Connect a USB1.1/Hi-Speed USB2.0 compatible USB
memory device, USB keyboard, or USB mouse.
r Ventilation Holes
1-7
1-8
Chapter 2 Handling
1. Documents....................................................... 2-2
Plain Paper............................................................2-2
Business Card.......................................................2-2
Card ......................................................................2-3
2. Preparing the Scanner ..................................... 2-4
Preparing the Document Feed Tray and
Eject Tray ..............................................................2-4
Feed Selection Lever ............................................2-5
USB Port ...............................................................2-5
3. Placing Documents .......................................... 2-6
Placing a Document ..............................................2-6
Placing a Folded Document ..................................2-7
Placing a Long Document .....................................2-7
Placing a Card.......................................................2-8
4. Clearing a Paper Jam or Double Feed Error ... 2-9
1. Documents
The ScanFront can scan documents in a range of sizes from business cards to Legal/A4.
It is possible to feed documents of the following sizes and thicknesses depending on the feeding method used.
❏ Plain Paper
Size
Width: 2" to 8 1/2" (50.8 mm to 216 mm)
Length: 2 1/8" to 14" (53.9 mm to 355.6 mm)
(up to 39.3" (1,000 mm) in Long Document mode)
Thickness for Page Separation ON
14 lb to 57 lb bond (52 g/m2 to 209 g/m2)
Thickness for Page Separation OFF
11 lb to 57 lb bond (40 g/m2 to 209 g/m2)
IMPORTANT
A document must meet the following criteria to be scannable:
• When scanning a multipage document, pages must be
grouped together so that they have the same size, thickness,
and weight. Scanning different types of paper at one time can
cause the scanner to jam.
• Always make sure that the ink on a document is dry before
scanning it. Scanning documents with the ink still wet may soil
the rollers or scanning glass, cause lines or smudges to
appear on images, or dirty other documents.
• Always clean the rollers or scanning glass after scanning a
document written in pencil. Scanning documents with pencil
written on them may soil the rollers or scanning glass, cause
stripes to appear in images, or dirty other documents.
• When scanning a two-sided document that is printed on thin
paper, the image on the opposite side of each page may show
through. Adjust the brightness in the scanning conditions
before scanning the document.
2-2
• Note that scanning the following types of documents can
cause a paper jam or malfunction. To scan such a document,
make a photocopy of the document and then scan the
photocopy.
Wrinkled or creased
documents
Carbon paper
Curled documents
Coated paper
Torn documents
Extremely thin,
translucent paper
Documents with
paper clips or staples
Document with square
punch holes
❏ Business Card
Size
Width: 2" (50.8 mm) and above
Length: 2 1/8" (53.9 mm) and above
Thickness
82 lb Cover (300 g/m2) and below
IMPORTANT
• If the stack of business cards that you placed is not fed
properly, reduce the number business cards.
• Business cards may sometimes be stacked in the wrong order
when they are ejected, depending on the size and thickness
of the business cards, and the orientation that they are loaded.
❏ Card
Size
2.12" × 3.37" (53.9 × 85.5 mm) (Conforming to ISO
Standards)
Thickness
0.0299" (0.76 mm) and below
2
Insertion orientation
Landscape
Handling
IMPORTANT
• Insert cards one at a time.
• Be careful when inserting cards to avoid damaging them.
2-3
2. Preparing the Scanner
When placing a document in the scanner, pull out the document eject tray so that it matches the size of the document, and then move
the feed selection lever to the appropriate position for the desired feed method (Page Separation ON or OFF) for the document.
❏ Preparing the Document Feed Tray and
Eject Tray
Prepare the trays in accordance with the type of document.
1. Open the document feed tray a.
2. Open the document eject tray b.
Hint
Open the center tray extension when output documents are
likely to fall out of the tray.
Hint
If the output documents curl in the eject tray when scanning
particularly thin documents, remove the eject tray.
To remove the document eject tray, push in on the illustrated
portions of the tray on both sides in the direction of the arrows
a and pull out b.
To reattach the eject tray, insert the protrusions on both sides of
the tray into the holes on the scanner.
After connecting the tray, make sure that it is attached securely.
2-4
❏ Feed Selection Lever
❏ USB Port
Change the position of the lever to the desired feed method
for the document.
You can insert a USB memory device to store image files.
Page Separation ON
Move the lever downward to separate a stack of documents
one page at a time in order to continuously feed the
documents.
2
Page Separation
ON
USB Memory
You can also connect a USB keyboard and USB mouse to
operate the ScanFront.
Page Separation
OFF
Feed selection lever
IMPORTANT
Moving the lever upward (Page Separation OFF) and then
scanning a stack of documents will cause multiple pages to be
fed at the same time.
IMPORTANT
• The scanner will not start if you turn the power ON while a USB
memory device is inserted. Insert the USB memory device
after the scanner starts up and the Home screen appears.
• Use USB memory that is not write-protected. If the USB
memory is write-protected, data cannot be written to the USB
memory.
• This scanner does not support USB memory equipped with
password security, data encryption, or functions other than
data storage.
• Make sure that the USB memory has sufficient space to store
images.
2-5
Handling
Page Separation OFF
Move the lever upward to feed a document with multiple
pages attached together such as an invoice one page at a
time without separating the pages.
3. Placing Documents
When placing documents into the scanner, place them face down into the tray with the top edge of the document at the bottom of
tray.
❏ Placing a Document
Follow the procedure below to place a document.
3. Place the document face down with its top edge at
the bottom of the tray.
1. Adjust the document guides to be wider than the
width of the document.
4. Adjust the document guides to fit the width of the
document.
2. Fan the document to offset the pages so that the top
edge of the first page is the lowest.
2-6
IMPORTANT
IMPORTANT
Make sure that document stacks placed in the feed tray do not
exceed the document guides.
The number of sheets that you can place in the scanner at
one time varies by paper size as follows.
Legal/A4 Size or Smaller:
50 sheets (stack 5 mm thick) or less
Sizes Larger than Legal/A4:
30 sheets (stacks 3 mm thick) or less
❏ Placing a Folded Document
Folio Scan enables you to scan documents that are larger
than Legal/A4 and therefore do not fit in the feeder. (The
maximum size is 11" X 17"/A3.) To use the function, fold
the document in half lengthwise and place it into the
feeder. The ScanFront will scan both sides and combine
the scanned images into a single image.
Hint
• When scanning folded documents, switch the feed selection
lever to OFF. (See p. 2-5.)
• When placing folded documents, place the document into the
scanner so that the fold is on the right side. The side of the
folded document facing you will become the right side of the
combined image.
• When scanning a document that is folded in half, set
[Scanning Side] to [Folio].
• The maximum size for combined images is A3. When
scanning a folded document of a size other than the standard
formats, set [Page Size] to [Auto size].
• When scanning a document that is folded in half, set
[Resolution (dpi)] to 300 dpi or less.
• When scanning a document that is folded in half, the [Double
feed detection by Ultrasonic] function cannot be used.
❏ Placing a Long Document
You scan documents up to 39.3" (1,000 mm) in length.
IMPORTANT
• When scanning a long document, set [Page Size] to [Auto size
(Long)].
• When scanning a long document, set [Resolution (dpi)] to 200
dpi or less.
• You cannot set [Scanning Side] to [Folio] when scanning a
long document.
2-7
2
Handling
Loading mark
• When folding the document, align the right and left sides and
create a sharp, straight fold. Otherwise the document may jam
or the image may not be aligned properly.
• The fold line itself will not be scanned. Keep this in mind if
there is content such as photos, diagrams, or text that spans
the fold.
• For Folio scanning, only the Page Separation OFF mode can
be used. Place documents one at a time.
• Adjust the document guides to fit the width of the document.
Otherwise, the image may scan as skewed or shifted.
❏ Placing a Card
When you want to scan a card, follow the procedure below
to place the card.
1. Move the feed selection lever upward (OFF).
IMPORTANT
When scanning cards, set the feed selection lever to OFF and
make sure to scan the cards one at a time.
CAUTION
• A card placed into the document feed tray in the portrait
orientation may not be output properly because a load is
placed on it during feeding. Furthermore, removing a card that
has caused a feeding error may damage the card, so make
sure to correctly insert the card.
• Pull the lock lever and open the panel unit before removing a
placed card. Inserting a finger into the scanner while the panel
unit is closed may result in an injury.
2. Adjust the document guides to match the width of the
card.
Lock lever
3. Place the card face down with the top edge at the
bottom of the tray.
2-8
4. Clearing a Paper Jam or Double Feed Error
When a paper jam or double feed error is detected, feeding and scanning stops.
1. Check the displayed message.
If a paper jam or double feed error is detected at the first
page of a document, the following messages appear.
If a paper jam or double feed error is detected in the middle
of a document, the following messages appear.
2
Handling
Hint
Hint
• If you press [Complete], the display returns to the previous
screen.
• If you want to continue scanning, reset the document before
progressing with screen operations. Press [Continue] to
resume scanning.
• If you press [Abort], the scanned images are canceled, and
the display returns to the previous screen.
• If you want to continue scanning, clear the document first
before touching the screen. After you reset the cleared
document, press [Continue] to resume scanning.
• If you press [Complete], the scanned images up until the
paper jam or double feed error are saved and scanning
completes. The display switches to the Send screen.
2-9
4. Pull out the jammed document in the direction that
IMPORTANT
When the message above is displayed and the scanner
transitions to Low Power Mode, all of the data scanned up until
that point is discarded. (See p. 3-3.)
seems the easiest to remove it.
2. Remove the scanned documents from the document
eject tray, and any documents remaining in the
document feed tray.
3. Pull the lock lever toward you and then fully open the
panel unit.
5. Close the panel unit and then place the document
again.
Lock lever
CAUTION
The open/close movement of the panel unit is linked to the up/
down movement of the document eject tray. Do not press on the
document eject tray when you open the panel unit.
6. Press [Continue] to resume scanning.
IMPORTANT
• If double feed errors occur repeatedly, reduce the number of
sheets you place in the document feed tray to about 10.
• A dirty or worn feed roller, or documents stuck together as a
result of static electricity are common causes of paper jams or
double feed errors.
If the feed roller is dirty, clean it. If paper jams or double feed
errors continue to occur even after cleaning, purchase an
Exchange Roller Kit and replace the rollers (feed roller and
retard roller), and document holding guides.
2-10
Chapter 3 Operating Procedures
1. Flow of Scanner Operations .............................3-2
2. Turning the Power ON and OFF.......................3-3
7. Registering and Editing Addresses ................ 3-19
Turning the Power ON.......................................... 3-3
Turning the Power OFF ........................................ 3-3
Registering a New Address ................................ 3-19
Modifying an Address ......................................... 3-22
Copying an Address ........................................... 3-22
3. Login Screen ....................................................3-4
8. Scan/Delivery Options.................................... 3-24
Login Screen Types.............................................. 3-4
When Using Server Authentication....................... 3-4
List Type Login ..................................................... 3-5
Key in Type Login................................................. 3-6
Scan Settings ..................................................... 3-25
File Formats........................................................ 3-29
Security Settings for PDF Files........................... 3-30
Delivery Options ................................................. 3-31
4. Screen Displayed after Login ...........................3-7
Home Screen........................................................ 3-7
Job Button Screen ................................................ 3-7
5. User Settings Screen........................................3-8
Change Password ................................................ 3-8
6. Scanning Procedures .......................................3-9
Scanning From the Home Screen ........................ 3-9
Scanning From the Job Button Screen............... 3-10
Address Selection Screen .................................. 3-11
USB Memory Screen.......................................... 3-13
Print Settings Screen.......................................... 3-14
Scanning............................................................. 3-15
1. Flow of Scanner Operations
The procedure and screen transitions for the process from turning the scanner ON, to sending an image file are as follows. For
descriptions of the various settings, refer to the appropriate reference pages.
Turn the power ON
(See p. 3-3.)
Users are registered (device/server authentication)
No user is registered
* When no user is registered and only
the Shared Address Book and Shared
Job Button are used
Login screen
(See p. 3-4.)
User Settings screen
(See p. 3-8.)
Home screen
(See p. 3-7.)
Password setting screen
(See p. 3-8.)
Address selection screen
(See p. 3-11.)
* Set the screen that appears after login in the user settings.
* When you use server authentication, the user that logged in
is registered automatically.
Job Button screen
(See p. 3-7.)
Scan/Delivery Options screen
(See p. 3-24.)
* Users restricted by [Use only Job
Buttons] in the function
restrictions cannot scan from the
Home screen.
Scanning starts immediately after a
job button is pressed.
Scan (The process after scanning differs depending on the Delivery Options)
(See p. 3-31.)
* Delivery Options
settings are also applied
to job buttons.
Scanning finishes (A document confirmation message appears)
(See p. 3-16.)
Send/Image Confirmation screen
(See p. 3-17.)
The image is sent
without the address
being confirmed.
The document and
image are not checked
Address Confirmation screen
(See p. 3-18.)
Send (The screen displayed after sending differs depending on the Delivery Options)
(See p. 3-31.)
Home screen
3-2
Job Button screen
Login screen
After scanning of the
document ends, the image is
sent as is and the process
ends.
2. Turning the Power ON and OFF
Use the power switch to turn the scanner ON, and press the [Power off] button on the touch panel to turn it OFF.
❏ Turning the Power ON
❏ Turning the Power OFF
Press the power switch to turn the scanner ON. The power
indicator lights, and the Home screen or the login screen
appears.
Press the [Power off] button displayed at the bottom left of
the panel to turn the scanner OFF.
Power switch
Home screen
3
Power
indicator
Hint
• It takes approximately 40 seconds for the Home screen to
appear after the power switch is turned on.
• If users have been registered, the login screen appears. (See
“Login Screen” on p. 3-4.)
• When the power indicator is lit but nothing appears on the
touch panel, Display Off has activated to turn the panel display
off. You can touch the panel to restore the display.
• When the power indicator is flashing but nothing appears on
the touch panel, the Low Power mode has activated to
temporarily stop scanner operations. To switch out of Low
Power mode, press the power switch or touch the touch panel.
• Contact the ScanFront administrator for details on the Display
off mode and Low Power mode settings.
3-3
Operating Procedures
IMPORTANT
• When restarting the scanner, wait at least 5 seconds after
turning the power OFF before turning it ON again.
• If the scanner stops responding, press and hold the power
switch to shut down the system, and then press the power
switch to turn the scanner ON again. In such cases, settings
configured immediately before shutting down may be lost.
3. Login Screen
The login screen appears at the startup when the scanner is turned ON.
❏ Login Screen Types
There are two types of login screen: a list type login screen
for selecting from a list of registered users, and a key in
type login screen for entering a user name and password.
List Type Login Screen
Hint
Set the type of login screen from [Device Operation] of the Web
menu (refer to p. 6-31 on the ScanFront 300/300P/330
INSTRUCTIONS) or [Login type setting] in the administrator
settings of the ScanFront (refer to p. 3-10 on the ScanFront 300/
300P/330 INSTRUCTIONS).
❏ When Using Server Authentication
The login screen when you use server authentication is a
key in type, and a list box is displayed for selecting Device
Authentication and Server Authentication.
Key in Type Login Screen
IMPORTANT
When you use server authentication to log in, you are registered
as a new user of server authentication.
3-4
❏ List Type Login
3. Enter a password and then press [OK].
Use the procedure below to log in to the list type login
screen.
1. Select the user to log in as from the list, and then
press [Next].
3
4. Press [Login] to log in to the scanner.
The password input screen appears.
2. Press [Password].
5. The Home screen (or Job Button screen) appears.
The keyboard screen appears.
3-5
Operating Procedures
IMPORTANT
Passwords are case-sensitive. Make sure to enter the password
correctly.
❏ Key in Type Login
3. Press [Login] to log in to the scanner.
In the key in type login screen, enter your user name and
password to log in.
1. Press [User name] ([Password]).
4. The Home screen (or Job Button screen) appears.
The keyboard screen appears.
2. Enter your user name (password) and then press
[OK].
IMPORTANT
• User names and passwords are case-sensitive. Make sure to
enter the user and password registered during device
authentication correctly.
• If you do not know the user name and password registered for
server authentication, contact the domain server
administrator.
3-6
4. Screen Displayed after Login
You can set the screen (Home screen or Job Button screen) that is displayed after a user logs in. (See p. 4-4.)
❏ Home Screen
❏ Job Button Screen
This screen enables you to select a job button to scan using
the conditions registered to the job button, and then send
the image file. (See “Scanning Procedures” on p. 3-9.)
3
a
c
a Select destination (E-mail, FTP, FAX, Shared
folder, USB memory, and Printer) buttons
These buttons open an address selection screen. (See
“Scanning Procedures” on p. 3-9.)
Hint
• The USB memory button is enabled when USB memory is
inserted in a USB port.
• [Printer] is enabled when the ScanFront is connected to a
network environment that is running ScanFront Service.
b [User settings] button
Enables setting of the user password. (See “User
Settings Screen” on p. 3-8.)
c [Administrator setting] button
Opens the Administrator Settings screen.
IMPORTANT
• The document is scanned immediately after you press the job
button. Make sure to place your document before you press
the job button. (See “Placing Documents” on p. 2-6.)
• Perform job button registration and editing via the Web menu.
• If you are unable to edit a job button, the editing of job buttons
has been restricted by the ScanFront administrator. For
details, contact the administrator.
IMPORTANT
If a user whose use of the Home screen is restricted logs in, the
Home screen is not available. For details, contact the
administrator.
3-7
Operating Procedures
b
5. User Settings Screen
The User Settings screen enables you to edit the user password.
❏ Change Password
You can register a new user password or change a user
password registered via the Web menu.
Hint
The old password does not need to be entered in order to
change a password. The new password that you entered is
registered.
3-8
6. Scanning Procedures
You can perform scanning from the Home screen or the Job Button screen.
❏ Scanning From the Home Screen
Press a destination selection (E-mail, FTP, Fax, Shared
folder, or USB memory) button to open an address
selection screen and then select an address to send an
image file.
IMPORTANT
If the network environment to which the ScanFront is connected
is not running ScanFront Service, [Printer] is grayed out and
cannot be selected.
3
If you select an address and then press [Next], the Scan/
Delivery Options screen appears. Set the scanning
conditions and then start scanning.
If you press the Printer destination selection button,
configure the printer settings.
3-9
Operating Procedures
If you press the USB memory destination selection button,
press [Downward] and specify the folder in the USB
memory to which you want to save the image file.
❏ Scanning From the Job Button Screen
If you press a job button, the Scan/Delivery Options screen
appears. Confirm the address and scanning settings
registered to the job button and then start scanning.
For details on the scanning procedure, read from the
setting of scanning conditions in Step 5.
IMPORTANT
• The settings screen display and the screen displayed after
scanning differ depending on the job button settings. For
details on the overall flow from configuring settings to sending
an image file, see “Flow of Scanner Operations” on p. 3-2.
• Job buttons cannot be used to save image files to USB
memory or send them to printers for printing.
3-10
❏ Address Selection Screen
From the address selection screen, you can select the address to send an image file and register addresses.
a
b
h
c
d
3
a Address Book type
Selects the address book type (Shared Address Book or
My Address Book). If the address book server setting is
enabled, [LDAP Address Book] is added.
b Address type
If you select the type of address (e-mail, fax, shared
folder, FTP, and groups) to display in the address list,
addresses of the selected type are displayed.
c Address List
Displays registered addresses and enables you to select
the address to send an image file.
Hint
• The following icons are used to indicate the types of address.
:E-mail
:Shared folder
:Fax
:FTP
:Group
• Pressing an address adds a checkmark (
) to the icon and
selects the address. Pressing a selected address again clears
the selection.
• An address is not selected as an address if there is no
checkmark added to the icon, even if the background of the
address is colored and the address appears selected.
Operating Procedures
e
f
g
• Each time you press an e-mail or group icon, the send
condition changes (To, Cc, Bcc).
:To
:Cc
:Bcc
:Selection cleared
d Jump Keys
If there are many addresses and the address you want is
not displayed in the address list, you can use these keys
to specify a keyword to search for and display the
address.
e [Clear All] button
Clears all address selections.
f [Edit] button
Enables you to register new addresses and edit
addresses.
g [Details] button
Displays detailed information for the address.
3-11
h My E-mail address
If “E-mail to my mailbox” is enabled in the user
settings of the Web menu, the mail address of the
logged in user is displayed.
When Sending to Fax Machines Directly Is
Enabled
If you are logged in as a user that has the “Permit to send
to FAX directly” enabled in the function restrictions in the
Web menu (Administrator Mode), a fax can also be sent to
an address that is not registered in the address book if you
directly enter the fax number in the address selection
screen.
3-12
❏ USB Memory Screen
The USB Memory screen enables you to specify the folder in the USB memory to save the image file.
a
b
c
d
3
e
f
Hint
• lIf you insert two or more USB memory sticks, numbers are
allocated to sticks from the second one onwards. For
example, the first one that was inserted is displayed as “USB
memory”, and the second one inserted is displayed as “USB
memory 2”.
• If you want to insert or replace a USB memory stick while the
USB memory screen is open, press the [Back] button to return
to the Home screen, update the USB memory information,
and then reopen the USB memory screen.
c [Upward] button
Enables you to move to a higher level folder when a
lower level folder is selected in the memory.
d [Downward] button
Enables you to move to a lower level folder in the USB
memory.
e [Edit] button
Enables you to register new folders and edit folders.
f [Format] button
Enables you to format the USB memory.
3-13
Operating Procedures
a Path
Enter the folder path of the USB memory. You can also
press [Downward] to select a folder.
b USB Memory Display
Displays the inserted USB memory.
❏ Print Settings Screen
The print settings screen enables you to specify the printer, paper size, and other print settings.
a
b
c
d
e
f
g
a Printer name
Select the printer that will be used to print the scanned
images. Printers that are compatible with the ScanFront
Service Server can be selected.
b Paper size
Select the paper size.
c Print format
Specify the method in which the scanned image is
scaled for printing.
• Actual size
Prints the scanned image in the same size as the
original document.
• Fit to paper
Prints while expanding or reducing the scanned image
to fit the paper size.
• Actual pixel
Prints while matching the resolution of the scanned
image.
d Orientation
Press [Portrait] or [Landscape] to specify the
orientation for printing.
3-14
e Copy number
Specify the number of copies to print.
f Duplex print
When you want to perform duplex printing, light this
button by pressing it.
g Color print
When you want to perform color printing, light this
button by pressing it.
IMPORTANT
The print settings you can configure will vary depending on your
printer. Settings and functions that are not supported by your
printer cannot be configured in this screen.
❏ Scanning
This section describes the procedure for scanning.
If you want to save the image file to USB memory, specify
the folder in the USB memory to save the image file in
Steps 2 to 4. (See “USB Memory Screen” on p. 3-13.)
3. Press a displayed address to select it.
A checkmark (
) is added to the icon for the selected
address. Pressing a selected address again clears the
selection.
1. Select a destination.
Press a destination button to select a destination.
3
4. Make sure the selected address has a checkmark
The address selection screen appears.
and then press [Next].
Hint
When a different type of address is selected, you can confirm
the selected address by pressing [Selected address] in the
Address type drop-down list.
2. Use [Address Book type] and [Address type] to
display the address to send the image file.
The Scan/Delivery Options screen appears.
3-15
Operating Procedures
IMPORTANT
An address is not selected as an address to send data to if there
is no checkmark, even if the background is shaded.
6. Press [Start] to start scanning.
Scanning stops after the document has been scanned.
5. Set the scan conditions. (See “Scan/Delivery
Options” on p. 3-24.)
IMPORTANT
When you use a job button for scanning, the subsequent
procedure varies as follows in accordance with the job button
settings. For details, see “Registering New Job Buttons” on
p. 4-18.
• If [When you select this Job Button] is set to [Skip Scan Setting
Screen] and you press a job button, scanning is started
without displaying the Scan/Delivery Options screen of Step 4.
• If [Send the files immediately after scanning] is set to [ON],
scanning ends without displaying the continue to scan
confirmation screen of Step 7 and then the address
confirmation screen of Step 10 appears.
• If [Confirm addresses before sending] is set to [OFF], the
image is sent without displaying the address confirmation
screen of Step 10 and the operation ends.
IMPORTANT
• If [Send the files immediately after scanning] is set to [ON] in
Delivery Options of the Scan/Delivery Options screen,
scanning ends without displaying the continue to scan
confirmation screen, and the address confirmation screen of
Step 10 appears.
• When the confirmation message is left displayed and the
scanner transitions to Low Power Mode, all of the data
scanned up until that point is discarded. (See p. 3-3.)
7. Check the document and go to the next step.
• Press [Abort] to cancel the scanned images and return to the
Scan/Delivery Options screen.
• Press the [Continue] button to resume scanning.
• Press [Complete] to go to the Send screen.
3-16
8. Check the scanned images.
Hint
When the preview image is enlarged, you can drag your finger
on the image to scroll.
3
Operating Procedures
: Display the image of the next page.
: Display the image of the previous page.
: Move the viewing area around an image
when an enlarged view of the image is shown.
: Rotate the image 90 degrees counterclockwise.
: Rotate the image 90 degrees clockwise.
: Enlarge the image.
: Reduce the image.
3-17
9. Press [Send].
10. Confirm the address and press [OK] to send the
scanned image.
The address confirmation message appears.
IMPORTANT
If a send error message appears, check the address settings
and send destination and try again.
11. Returns to the screen set for [Screen after sending]
in Delivery Options of the Scan/Delivery Options
screen.
IMPORTANT
If [Confirm addresses before sending] is set to [OFF] in Delivery
Options of the Scan/Delivery Options screen, the image is sent
without displaying the address confirmation screen and the
operation ends.
3-18
7. Registering and Editing Addresses
If an address to which you want to send an image file is not registered in the address book or the information of a registered address
has not been updated, use the procedure below to register a new address or modify an address in the address book.
❏ Registering a New Address
1. Make selections for [Address Book type] and
[Address type], press [Edit], and then press [New].
• Name
Enter the name to appear in the address book.
• E-mail address
Enter the sender’s address for when image files are sent
by e-mail.
3
Shared Folder Registration Screen
Operating Procedures
2. Register the address in accordance with the setting
conditions of the address type.
E-mail Registration Screen
• Name
Enter the name to appear in the address book.
• Host name
Enter the name of the computer containing the publicly
shared folder. When the ScanFront Service is running,
you can enter the IP address instead of a host name.
• Folder path
Enter the name of the shared folder and the path of the
sub-folder to register.
3-19
Hint
If the path of the sub-folder is unknown, use the procedure
below to specify the sub-folder.
1. Enter the host name, user name, password, and domain, and
then press [Browse] to access the computer that is making
the shared folder public.
2. Specify any sub-folder within the displayed folder.
3. Press [Downward] to move to a level lower than the selected
folder, or press [Edit] and [Create a new folder] to create a
new folder.
• User name/Password
Enter the user name and password of an account with
write permission for the shared folder.
• Domain/Workgroup
If the computer containing the shared folder is part of a
domain, enter the domain name.
• Save password
Save the entered password.
FTP Registration Screen
• Folder path
Enter the path of the sub-folder when specifying a subfolder on the FTP server.
Hint
If the path of the sub-folder is unknown, use the procedure
below to specify the sub-folder.
1. Enter the server address, user name, and password, and
click [Browse] to log in to the FTP server.
2. Specify any sub-folder at the level of the displayed folder and
click [OK].
• User name/Password
Enter the user name and password for logging in to the
FTP server.
IMPORTANT
Enter the user name and password of an account with write
permission for the FTP server.
• Port number
Enter the port number. The standard port number is 21.
• Save password
Save the entered password.
• Use passive mode
Use passive mode for sending to the FTP server.
IMPORTANT
Use passive mode when normal communication with the FTP
server cannot be established. However, be aware that
communication may not be possible if the network is not
functioning properly.
• Name
Enter the name to appear in the address book.
• FTP server
Enter the address of the FTP server.
3-20
Fax Registration Screen
• [Add] button
Select addresses to register to the group from [Address
Book type] and [Address type]. The selected addresses
are displayed in the list.
3
Group Registration Screen
IMPORTANT
• When you add shared folders to groups, do not add multiple
shared folders with different access privileges to one group.
• Using a group to simultaneously send to shared servers and
the like and multiple shared folders with different access
privileges may result in a send error.
• Name
Enter the name that you want to appear in the address
book.
3-21
Operating Procedures
• Name
Enter the name to appear in the address book.
• Fax number
Enter the recipient fax number.
❏ Modifying an Address
Modify an address when there is a send error because the
information of the transfer destination registered for the
address is wrong or has been changed.
1. Select the type of the address to modify and press
[Details].
4. Modify the address.
Hint
For details on editing items, see “Registering a New Address”
on p. 3-19.
❏ Copying an Address
You can copy addresses between My Address Book and
Shared Address Book.
1. Select the address book entry to copy.
2. Select the address, press [Edit], and then press
[Copy].
Detailed information for the address appears.
2. Check the detailed information for the selected
address.
3. Press [Edit], and then press [Modify].
The selected address is copied to memory.
3. Select the address book type, press [Edit], and then
press [Paste].
The edit screen for the address appears.
3-22
A confirmation message appears.
3
Operating Procedures
4. Press [New] and paste the address.
Hint
If the address book already has an address with the same name
as the pasted one, the following message appears.
• If you select [New], an address with the same name is created
in the address book.
• If you select [Overwrite], the existing address with the same
name is overwritten.
3-23
8. Scan/Delivery Options
This section describes the scan settings and send settings for the scanner.
g [Default] button
Resets any modified settings to the default values of the
scanner.
c
a
IMPORTANT
b
d
e
i
j
f
k
g
h
a Address Display Area
Displays the selection that you made on the address
selection screen or the addresses registered to the job
button.
b Details
Displays detailed information for the address with the
colored background.
c Scan Settings
Sets the scan conditions. (See “Scan Settings” on p. 3-25.)
d Detailed settings
Configures detailed settings for scan conditions. (See
“Detailed Settings” on p. 3-26.)
e File format
Checks the displayed file format and press the [File
format] button to configure the settings. (See “File
Formats” on p. 3-29.)
f Delivery Options
Sets the send conditions. (See “Delivery Options” on
p. 3-31.)
3-24
If you press [Default] in the Scan/Delivery Options screen
opened from a job button, the settings are reset not to the
setting values registered to the job button, but to the default
values of the scanner.
h [Start] button
Starts scanning.
i [Deskew] button
The scanner detects from the scanned image that the
document was fed askew and then straightens the image.
j [Prescan] button
When scanning starts, the first page of the document is
scanned and then scanning stops. You can view the image
of the first page to check and adjust the brightness and
contrast before scanning the entire document.
Hint
• Scanning pauses after the first page of the document is
scanned, and the image of the first page is displayed.
• Use the displayed image to confirm and adjust the brightness
and contrast. Press [Continue] to confirm the adjusted
brightness and contrast for the first image and continue
scanning.
k [Back] button
Returns the display to the previous screen.
❏ Scan Settings
TIFF
JPEG
PDF
The scan settings include basic condition settings (page
size, mode, resolution, scanning side, and brightness) and
detailed settings for scanning.
Basic Condition Settings
Paper size
Mode
Resolution
Scanning
side
Resolution
Select the resolution for scanning.
IMPORTANT
Paper Size
Select the size of the document you want to scan.
Hint
• Select [Auto size] to automatically detect the size of the
scanned document.
• When scanning a long document, select [Auto size (Long)].
IMPORTANT
A resolution of [300 dpi] or more cannot be set when [Auto size
(Long)] is selected.
Mode
Select the mode for scanning.
IMPORTANT
• The selection of modes is limited depending on the setting set
for File Format (see p. 3-29).
• A resolution of [300 dpi] or more cannot be set when [Auto size
(Long)] is selected for [Page Size].
• A resolution of [400 dpi] or more cannot be set when [Folio] is
selected for [Scanning Side].
• When you are using the scanner in Web Application Mode
(ScanFront 330 only), [Resolution] cannot be set to [600 dpi]
when [Mode] is set to [Color].
Scanning Side
Select the method for scanning the document (Simplex,
Duplex, Skip Blank Page).
Hint
• The Skip Blank Page option scans both sides of a document
and skips saving any image it determines to be a blank page.
• Selecting Skip Blank Page enables the skip blank page setting
in the detailed settings. (See “Skip Blank Page” on p. 3-26.)
• When you select Folio, documents that are folded in half for
which duplex scanning is performed can be scanned as a
single image.
IMPORTANT
• The scanning speed may be reduced when [Skip Blank Page]
is selected.
3-25
3
Operating Procedures
• When [Text enhance] is selected, [Bleed-through reduction] in
the Detailed Settings screen is grayed out and cannot be
selected.
• The [Auto Color Detection] function cannot be used
simultaneously with the color drop-out or prescan function.
• The scanning speed may be reduced when the Auto Color
Detection function is used.
• A resolution of [400 dpi] or more cannot be set when [Folio] is
selected. In addition, [Double feed detection by Ultrasonic] is
grayed out and cannot be selected.
Brightness
Adjust the brightness to match the density of the
document.
Hint
When you want to scan both sides of a document that has front
and back sides of different densities, you can change the
settings for the brightness of the front side and back side
separately in the detailed settings and then perform scanning.
Detailed Settings
Press the [Detailed settings] button to open the Detailed
Settings screen.
Double feed detection by Ultrasonic (Only
Available with the ScanFront 330)
The scanner uses an ultrasonic sensor to detect when two
or more documents are fed together, and stops feeding
when a double feed is detected.
IMPORTANT
• This method is effective when documents overlap by 1.97"
(50 mm) or more. It does not function if only a slight portion of
the document is overlapping.
• When [Scanning Side] is set to [Folio], [Double feed detection
by Ultrasonic] is grayed out and cannot be selected.
Double feed detection by length
The scanner detects by document length when two or more
documents are fed together, and stops feeding when a
double feed is detected.
IMPORTANT
• Using the length of the first page of the document as a
reference, the scanner determines a double feed when it
detects a document with a length at least 1.38" (35 mm)
longer or shorter than the reference length.
• Set [Double feed detection by length] to [OFF] when scanning
a document that contains pages of different lengths.
Skip Blank Page
When [Skip Blank Page] is selected in the scanning side
settings, this setting is enabled, and you can adjust the
sensitivity level for skipping blank pages.
3-26
Hint
Deskew
• The initial value for the Skip Blank Page option is set to “90.”
• As you lower the value from the default setting, pages of the
document with text become more likely to be skipped as well.
• As you raise the value from the default setting, pages of the
document that are blank become less likely to be skipped.
IMPORTANT
• As you lower the Skip Blank Page value from the default
setting, it is then set so that pages of the document with text
are more likely to be skipped.
• As you raise the Skip Blank Page value from the default
setting, it is then set so that blank pages of the document are
less likely to be skipped.
IMPORTANT
If you select [Prefer Quality], the scanning speed is reduced. If
you are scanning a large number of pages, select [Prefer
Speed] to prevent a decrease in scanning speed.
Rotates the scanned image a specified amount.
Bleed-through reduction
Hint
If you select [Auto], the orientation of text within the document is
detected and the image is rotated so that the orientation of the
text is correct.
IMPORTANT
The scanning speed may be reduced when [Auto] is selected.
Eliminates bleed-through images, in which images on the
reverse side of a scanned document appear on the scanned
page, such as when scanning thin documents with text or
images on both sides.
IMPORTANT
Bleed-through reduction cannot be set when the [Text enhance]
mode is selected.
3-27
3
Operating Procedures
Document orientation
The scanner detects from the scanned image that the
document was fed askew and then straightens the image.
• Prefer Quality
Image processing is performed to minimize the loss of
quality of an image that has deteriorated as result of
deskewing.
• Prefer Speed
The image deteriorates slightly as a result of deskewing.
Hint
When using bleed-through reduction, adjust the bleed-through
reduction level to match the type of document.
Contrast
The color drop-out function has a “drop-out” effect that
leaves out a specified color (red, blue, or green) while
scanning, and a “color enhancement” effect that
emphasizes a specified color. You can set each of these
effects for the front side and back side.
IMPORTANT
The color drop-out settings are disabled when the scanning
mode is set to [Color].
Auto Color Detection Settings
Adjust the contrast for the images to scan.
Back side Brightness/contrast
This is enabled when you scan both sides of a document
and should be used when the document has front and back
sides of different density. Select [Use back side brightness
(contrast)] to change the settings for the brightness and
contrast of the front and back sides of the document.
Front side (Back side) color drop-out
This is enabled when Auto Color Detection is selected, and
allows you to configure the following detection settings
for determining whether to scan a document in color or
black and white.
• Mode in case of binary
Specify the scanning mode to use when a black and white
document is detected.
• Threshold intensity to judge the document as color
Adjust the sensitivity to colors in a document.
• Aresize to judge the document as color
Specify the ratio of colored regions in a document.
IMPORTANT
• The [Auto Color Detection] function cannot be used
simultaneously with the color drop-out or prescan function.
• The scanning speed may be reduced when the Auto Color
Detection function is used.
3-28
❏ File Formats
PDF format
You can select from the three available file formats TIFF,
JPEG, and PDF, and the modes available for scanning
vary, depending on the file format setting. (See “Mode” on
p. 3-25.)
TIFF format
3
JPEG format
Select the compression rate for JPEG compression.
3-29
Operating Procedures
Select [Single page (Front/back separate file)] to save each
side of each page as a separate image file, [Single page
(Front/back same file)] to save each page as a separate
image file, or [Multi page] to save one image file
containing multiple pages when scanning multiple pages.
Configure the following settings for saving in PDF format.
• Compression
Select the compression method.
• Quality
Adjust the quality for the specified compression method.
• Multi page settings
Select [Single page (Front/back separate file)] to save
each side of each page as a separate image file, [Single
page (Front/back same file)] to save each page as a
separate image file, or [Multi page] to save one image
file containing multiple pages when scanning multiple
pages.
• OCR (Character Recognition)
If OCR is set to On, character recognition is performed
for the text within the scanned document, and the text is
embedded in the PDF file as text information.
The [Language setting] button enables you to select the
language for character recognition.
• Encryption (Security)
If you set encryption to On and then press the [Security
settings] button, the Security settings screen appears, and
you can configure the security settings for the PDF file.
For details, see “Security Settings for PDF Files” on
p. 3-30.
❏ Security Settings for PDF Files
Apply security to the PDF file.
Encryption Level
High (128-bit RC4) and low (40-bit RC4) level settings are
available.
IMPORTANT
Using the High (128-bit RC4) level setting is recommended. The
Low (40-bit RC4) level setting provides less security.
Requires a password to open the document
Viewing of the document is restricted by a password.
IMPORTANT
Take care not to forget the password once it is set. If you forget
the password, the document can no longer be opened.
3-30
Use permissions password to restrict editing
security settings
The following settings are restricted by the permissions
password.
• Printing allowed
This permits printing of the PDF file with a printer.
• Changes allowed
This permits editing of the PDF file; for example, adding
and deleting pages.
• Enable copying of text, images, and accessibility.
This enables the copying of text information embedded
with OCR software and reading of the PDF file with
voice software.
IMPORTANT
• Password protection is recommended when the permissions
of the PDF file are restricted.
• You can change the permissions and cancel password
protection for a password protected PDF file in an application
capable of editing PDF files such as Adobe Acrobat.
❏ Delivery Options
Action when the same named file exists
Set the action to perform when there is already a file of the
same name at the destination.
• Display a message
Display a message to confirm overwriting of the file.
• Abort sending
Cancel sending.
• Overwrite the file
Overwrite the file at the destination.
3
Operating Procedures
E-mail settings (subject, message)
Set the subject and message for sending via e-mail.
File name
Specify a name for the image file to be sent.
Auto file name
The scanner adds 17 digits that indicate the date and time
to the file name of the image to be sent.
Ex.) May 14, 2013, 3:40:30 p.m.
yyyymmdd: File name + 20130514154030123
mmddyyyy: File name + 05142013154030123
ddmmyyyy: File name + 14052013154030123
* The last three digits indicate the number of milliseconds.
When custom file name settings are configured in the Web
Menu, you can select [Custom] to add the custom file
name to the file name of the scanned image (see p. 4-6).
Send the files immediately after scanning
Send images without checking them when scanning
completes.
Confirm addresses before sending
Confirm the addresses before sending images when
scanning completes.
IMPORTANT
• Make sure you set either [File name] or [Auto file name]. A
message appears if you do not enter a file name and then set
[Auto file name] to [None].
• If you select [Single page] of TIFF format, or JPEG format, a
4-digit sequential number starting with “0001” is added
automatically to the end of file names.
• The following characters cannot be used to set the custom file
name:
/:?*"<>|
3-31
Screen after sending
Select the screen to display after sending images.
• Home screen (Job Button screen)
Redisplay the Home screen (Job Button screen) after
sending images.
IMPORTANT
• The [Screen after Login] setting that is set via the Web menu
by the user applies to the Home screen (Job Button screen)
setting.
• The Job Button screen is displayed for a user for which use of
the Home screen is restricted by the ScanFront administrator.
• Logout
The user is logged out after sending images.
• Select screen after sending
A dialog box for selecting the screen after sending
images is displayed.
Hint
When no user is registered, the Logout option does not appear.
Send index file
Specify whether to send index files (metadata) with
images.
When sending index files, enter an index string.
Index files are created according to the settings configured
in the Web Menu (see p. 4-7).
IMPORTANT
The following characters cannot be used in strings contained in
the index file:
&"'<>
3-32
Chapter 4 Web Menu (User Mode)
1. Web Menu Overview........................................ 4-2
2. Logging In to the Web Menu............................ 4-3
3. User Settings ................................................... 4-4
User Settings.........................................................4-5
4. Address Book Settings..................................... 4-9
Registering New Addresses................................4-11
Copying Addresses .............................................4-14
Exporting and Importing Address Books.............4-14
5. Job Button Settings........................................ 4-16
Registering New Job Buttons..............................4-18
Scan Settings Overview ......................................4-19
Copying Job Buttons ...........................................4-23
Editing Jobs.........................................................4-24
Exporting and Importing Job Buttons ..................4-24
1. Web Menu Overview
The Web Menu function enables you to access and configure the scanner from the Web browser of a remote computer. From the
Web Menu, you can register address books and job buttons.
Computer (Web Menu)
Settings
Network
ScanFront
IMPORTANT
•
•
•
•
For a Web browser, use Microsoft Internet Explorer 6.0 or later or Firefox 3.5 or later.
In some cases, settings cannot be changed from the Web Menu when the ScanFront administrator or another user is logged in to the scanner.
Use the device name or IP address assigned to the scanner as the URL for logging in to the Web Menu. (See p. 4-3.)
When you open the Web Menu, an SSL-certificate warning will appear. However, you can proceed and open the Web Menu safely.
Web Menu (User Mode)
a
b
c
a User Settings (See “User Settings” on p. 4-5)
Use to change the user settings.
b Address Book Settings (See “Address Book Settings”
on p. 4-9)
Use to register and manage entries in the Shared Address
Book available to all users, and the My Address Book
provided for each user.
4-2
c Job Button Settings (See “Job Button Settings” on
p. 4-16)
Use to register and manage the Shared Job Button
available to all users, and the My Job Button provided for
each user.
2. Logging In to the Web Menu
You can log in to the Web Menu using the following procedure.
Hint
Use the device name or the IP address assigned to the scanner as the URL for accessing the Web Menu. Contact the ScanFront administrator
for the device name and the IP address.
1. Turn the scanner ON.
2. Confirm the IP address with the administrator.
3. Launch the Web browser on the computer.
4. Enter the device name or the IP address as the URL
to open the Web Menu.
Ex.) http://scanfront when the device name is ScanFront, and
http://172.19.xxx.xxx for the IP address.
IMPORTANT
If [Authentication Method] appears above [User name] on the
login screen, users can log in from an account registered on a
domain server (Server Authentication), instead of logging in
from an account registered on the scanner (Device
Authentication). For details, consult the ScanFront
administrator.
4
Menu.
Hint
If the Web Menu is set to Administrator Mode, click [To User
Mode].
IMPORTANT
User names and passwords are case-sensitive. Make sure to
enter them correctly.
4-3
Web Menu (User Mode)
5. Enter a user name and password to log in to the Web
3. User Settings
From the User Settings screen, you can change the information of a user logged in by Device Authentication.
a
a Setting (See “User Settings” on p. 4-4)
Allows you to edit a user’s settings.
4-4
❏ User Settings
Click [Setting] to edit the user information.
User Settings
Home Screen
4
Job Button Screen
Web Menu (User Mode)
• User name
Enter a new user name.
• Change Password
Select the [Change Password] check box, and then enter
the new password and confirmation password.
• Mail Address (Not Changeable)
To change the e-mail address, contact the ScanFront
administrator.
• SMTP/POP Before SMTP Authentication
Appears when [Auth Method] is configured to any
setting other than [SMTP] by the administrator in the
mail server settings. Enter the [User name] and
[Password] that will be used for mail server
authentication here.
• Screen after Login
Select the Home screen or the Job Button screen as the
first screen to appear after the user logs in.
IMPORTANT
• When entering a [Password], select the [Change Password]
check box before entry.
• [Change Password] updates the password information
saved on the scanner, but does not alter the password
registered on the server.
• For a user logged in by Server Authentication, you can only
select a setting for [Screen after Login].
• E-mail address may not be registered for a user logged in by
Server Authentication. For details on e-mail address
settings, consult the ScanFront administrator.
IMPORTANT
• The setting for the startup screen after login also affects which
screen appears after a scanned image is sent. (See “Delivery
Options” on p. 4-18.)
• If the ScanFront administrator has restricted use of the Home
screen, only [Job Button screen] is available for the [Screen
after Login] setting. For details, consult the ScanFront
administrator.
4-5
• Default Address Book screen
Select “My Address Book” or “Shared Address Book”
for the address book type when the address selection
screen is displayed from the Home screen.
• Default Job Button screen
Select “My Job Button” or “Shared Job Button” for the
job button type when the job button screen is displayed
after login.
• E-mail to my mailbox
Select the [Enable] check box to display the e-mail
address of the logged in user in the address book.
If an e-mail address is set for the user, the user’s e-mail
address will be displayed even if it has not been
registered in the address book.
The user’s e-mail address is displayed at the very top of
the address list.
Custom File Name Settings
Specify the method in which file names used for saving
scanned images are created. When you select to use
custom file names during a scanning procedure, the image
files will be saved under file names that are determined by
the settings configured here. Components of the custom
file name will be included in the order that they appear on
this screen.
4-6
IMPORTANT
The following characters cannot be used to set the custom file
name:
/:?*"<>|
• Separator
Select the [Enable] check box to include a separator
between character strings in the file name, and select a
character to use as the separator in the list box.
• String
Specify a string to include in the file name.
• User name
Select the [Enable] check box to include the user name in
the file name.
• Date
Select the [Enable] check box to include the date in the
file name, and select a format for the date in the list box.
• Time
Select the [Enable] check box to include the time in the
file name, and select a format for the time in the list box.
• Device name
Select the [Enable] check box to include the device name
in the file name.
• Counter/Start number/Number of digits
Select the [Enable] check box to include a counter in the
file name. When this is enabled, you can specify the
starting value and number of digits used for the counter.
Index Settings
Specify the content of index files (metadata) that are
attached to scanned image files. Components of the index
file will be included in the order that they appear on this
screen.
• Index string/Field name
Enter a string for the index. You can change the default
field name (“String”) as necessary.
• User name
Select the [Enable] check box to include the user name in
the index file. You can change the default field name
(“User”) as necessary.
4-7
4
Web Menu (User Mode)
IMPORTANT
The following characters cannot be used in strings contained in
the index file:
&"'<>
• Date
Select the [Enable] check box to include the date in the
index file, and select a format for the date in the [Format]
list box. You can change the default field name (“Date”)
as necessary.
• Time
Select the [Enable] check box to include the time in the
index file, and select a format for the time in the [Format]
list box. You can change the default field name (“Time”)
as necessary.
• Device name
Select the [Enable] check box to include the device name
in the index file. You can change the default field name
(“Device”) as necessary.
• Counter/Start number/Number of digits
Select the [Enable] check box to include a counter in the
index file. When this is enabled, you can specify the
starting value and number of digits used for the counter.
You can change the default field name (“Counter”) as
necessary.
• File name
Select the [Enable] check box to include the file name in
the index file. You can change the default field name
(“FileName”) as necessary.
• File size
Select the [Enable] check box to include the file size in
the index file. You can change the default field name
(“FileSize”) as necessary.
• Number of Pages
Select the [Enable] check box to include the number of
pages that are in the scanned image in the index file. You
can change the default field name (“PageNumber”) as
necessary.
• Destination path
Select the [Enable] check box to include the destination
path in the index file. You can change the default field
name (“Folder”) as necessary.
• Index file format
Specify a file format for the index files.
[OK] button
Updates the user information with the changed settings.
4-8
4. Address Book Settings
From the Address Book Settings screen, you can register entries in the Shared Address Book, which is available to all users, and
the My Address Book, which is provided for each user.
a
d
e
b
f
g
c
h i
j
4
f [Select All] button
Selects all of the displayed addresses.
g [Except All] button
Deselects all of the displayed addresses.
h [Copy] button
Copies the selected address. Only enabled when an
address is selected. (See “Copying Addresses” on p. 4-14.)
i [Delete] button
Deletes the selected address. Only enabled when an
address is selected.
j Address List
Displays the registered addresses.
• Check box: Select this check box to select an address.
• Address type (icon)
: FTP
: Shared folder
: E-mail
: Fax
: Group
• Edit: Click to edit an address.
4-9
Web Menu (User Mode)
a Type of Address Book
Selects the address book (Shared Address Book or My
Address Book) to edit.
The LDAP Address Book is also selectable if the address
book server settings are enabled and permission to use the
LDAP address book has been granted to the user. The
address type is set to [E-mail] when the LDAP Address
Book is selected.
b Export from ScanFront
Exports the address book data as a file in CSV format. (See
“Exporting and Importing Address Books” on p. 4-14.)
c Import to ScanFront
Imports a previously exported address book data file. (See
“Exporting and Importing Address Books” on p. 4-14.)
d Address type
Selects the type of addresses (E-mail, FTP Server, Shared
folder, Group, or All) to display.
e [New Address] button
Registers a new address book entry.(See “Registering New
Addresses” on p. 4-11.)
IMPORTANT
If the ScanFront administrator has restricted editing of the address books, the following Address Book settings apply. For details, consult the
ScanFront administrator.
• If editing is restricted for only one address book (either the My Address Book or the Shared Address Book), users can only copy addresses
from the restricted address book and paste them into the unrestricted address book.
• If editing is restricted for both the My Address Book and the Shared Address Book, users can only view detailed address information.
4-10
❏ Registering New Addresses
Select the type of address book (Shared Address Book or
My Address Book), and click [New Address] to register a
new address.
Address type: FTP Server
This option registers a network FTP server.
IMPORTANT
FTP servers that require firewall settings cannot be registered.
Hint
• The number of addresses that can be registered to the Shared
Address Book (My Address Book) is up to 1000 in combination
with the total number of addresses included in the Shared Job
Button (My Job Button).
• For the number mentioned above, the count for a group is the
number of addresses registered to the group (maximum of 99
addresses) plus the group name, so a group with 99
addresses registered to it is counted as having 100
addresses.
• The available settings vary, depending on the type of address
(E-mail, FTP Server, Shared folder, Fax, or Group).
4
Name
Enter the name to display on the scanner.
Address type: E-mail
FTP server
Enter the IP address or host name of the FTP server.
Folder path
To specify a subfolder on the FTP server, enter the path to
the subfolder.
Hint
Enter the destination e-mail address.
If you are unsure of the subfolder’s path, use the following
procedure to specify the subfolder:
1. After entering the [FTP server], [User name], and [Password],
click [Browse] and log in to the FTP server.
2. In the folder that appears, specify any subfolder and click
[OK].
[OK] button
User name/Password
Registers a new e-mail address with the specified
parameters.
Enter the user name and password required to log in to the
FTP server.
Name
Enter the name to display on the scanner.
E-mail Address
IMPORTANT
Make sure to enter the user name and password of an account
with the authority to write data to the FTP server.
Port number
Enter the port number. The standard port number is 21.
4-11
Web Menu (User Mode)
This option registers an e-mail address.
Save Password
[Browse] button
Saves the entered password.
Shows a list of computers connected to the network for
you to specify a shared folder.
Passive Mode
Uses passive mode to send transmissions to the FTP
server.
IMPORTANT
Use passive mode when normal communication with the FTP
server cannot be established. However, be aware that
communication may not be possible if the network is not
functioning properly.
[OK] button
Registers a new FTP server with the specified parameters.
Address type: Shared folder
This option registers a folder shared publicly on the
network.
Hint
You can display the shared folders using the following
procedure.
1. After entering the computer name, user name, password,
and domain/workgroup, click [Browse]. Access the computer
containing the publicly shared folder.
2. Specify any subfolder from the displayed computer and click
[OK].
IMPORTANT
• If you click [Browse] without entering the user account
information, only computers and workgroups within the same
network address will display.
• When displaying workgroups that are not part of a domain,
you cannot display computers or workgroups with different
network addresses.
• Not all workgroups and computers in the network can be
displayed immediately after the ScanFront is started. If some
workgroups and computers are not displayed, wait a few
minutes and then press [Browse].
• A new folder cannot be created in a specified folder via the
Web Menu. If you want to create a new folder, use the
computer set as the FTP server or the address editing
functions of the ScanFront to create a folder beforehand.
User name/Password
Name
Enter the name to display on the scanner.
Computer Name (Host Name)
Enter the name of the computer containing the publicly
shared folder. When the ScanFront Service is running, you
can enter the IP address instead of a host name.
Folder path
Enter the path to the subfolder that you want to register as
the name of the shared folder.
4-12
Enter the user name and password of an account with the
authority to write data to the shared folder.
Domain/Workgroup
If the computer containing the shared folder is part of a
domain, enter the domain name.
IMPORTANT
• If the computer containing the publicly shared folder is part of
a domain, enter the user name and password registered with
the domain, and the domain name.
• If the computer containing the publicly shared folder is not part
of a domain, there is no need to enter a [Domain/Workgroup].
Save Password
Select this check box to save the password to the address.
IMPORTANT
If you do not save the password, password entry will be required
each time you send.
[OK] button
Registers a new shared folder with the specified
parameters.
Address type: Group
This option registers several registered addresses together
as a group.
Hint
Different types of address, such as e-mail addresses and
shared folders, can be registered as a group, and up to 99
addresses can be registered to 1 group.
Address type: Fax
This option registers a fax destination.
4
Name
Enter the fax number of the destination.
[OK] button
Registers a new fax destination with the specified
parameters.
Enter the name to display on the scanner.
Add from Address Book
Allows you to select an address from an address book, add
it to the group, and display it in the list.
[OK] button
Registers a new group with the specified parameters.
4-13
Web Menu (User Mode)
Fax number
❏ Copying Addresses
You can copy an address and register it as a new address.
You can also copy an address from one address book to
another.
As an example, this section describes how to copy from the
Shared Address Book to the My Address Book.
Hint
Use this function when you want to copy an address between
the Shared Address Book and My Address Book or copy an
address and register it as a different address in the same
address book after changing some of the settings.
1. Select Shared Address Book for the [Type of Address
Book].
❏ Exporting and Importing Address Books
You can back up your address books as files in CSV
format, and import the backed up address book data to
another ScanFront unit.
Hint
If you have multiple ScanFront units, you can use the same
address books on all of them by importing the address book
settings file registered on one ScanFront unit to the other units.
Exporting from the Scanner
You can save the address book data to a specified folder.
1. Click [Export from ScanFront].
2. Add a checkmark to the check box of the address you
want to copy and then click [Copy].
2. Click [Save], specify a save location, and save the
address book data.
Hint
3. Select My Address Book for the copy destination, and
click [OK].
4. Confirm the copied address.
4-14
• You can open the saved CSV file with software that supports
CSV files such as spread sheet software in order to check the
structure of the file.
• You can match the structure of a CSV file created in another
mailer to that of a CSV file saved on the ScanFront, and then
import the address book of the other mailer and use it on the
ScanFront.
Importing to the Scanner
You can import previously exported address book data to
the scanner.
1. Click [Import to ScanFront].
2. Click [Browse] and specify a previously exported
address book settings file.
3. Select a processing method for importing the
address book settings file.
• Replaces the whole data: Deletes all currently
registered address book entries and overwrites them with
the imported address book data.
• Appends data: Adds the imported address book data to
the currently registered address book.
4
Web Menu (User Mode)
4. Click [Execute].
Confirm the message that appears, and click [OK] to
import the data.
Hint
When importing is completed, the following message appears.
Click [OK] to return to Address Book Settings and confirm the
imported address data.
4-15
5. Job Button Settings
From the Job Button Settings screen, you can register the Shared Job Button, which is available to all users, and the My Job Button,
which is provided for each user.
a
d
b
e
f
c
g h
i
a Job Button Type
Select the job button (Shared Job Button or My Job
Button) that you want to edit.
b Export from ScanFront
Exports the job button data as a file in DAT format. (See
“Exporting and Importing Job Buttons” on p. 4-24.)
c Import to ScanFront
Imports a previously exported job button data file. (See
“Exporting and Importing Job Buttons” on p. 4-24.)
d [New Job Button] button
Registers a new job button. (See “Registering New Job
Buttons” on p. 4-18.)
e [Select All] button
Selects all of the displayed job buttons.
4-16
f [Except All] button
Deselects all of the displayed job buttons.
g [Copy] button
Copies the selected job button. Only enabled when a job
button is selected. (See “Copying Job Buttons” on
p. 4-23.)
h [Delete] button
Deletes the selected job button. Only enabled when a job
button is selected.
i Job Button List
Displays the registered job buttons.
• Check box: Select this check box to select a job button.
• Edit: Click to edit a job button.
IMPORTANT
If the ScanFront administrator has restricted editing of the job buttons, the following Job Button settings apply. For details, consult the ScanFront
administrator.
• If editing is restricted for only one set of job buttons (either the My Job Button or the Shared Job Button), users can copy job buttons from the
restricted set of job buttons and paste them into the unrestricted set.
4
Web Menu (User Mode)
• If editing is restricted for both the My Job Button and the Shared Job Button, users can only view detailed job button information.
4-17
❏ Registering New Job Buttons
Address
Click [New Job Button] to register a new job button.
Job Button Settings
Click [Add from Address Book], open the Address page,
and select the address to send to.
IMPORTANT
Name of Job Button
Enter the job button name to display on the touch panel.
Hint
• Job buttons are sorted and displayed by job button name. If
you want to set to display job buttons in a particular order,
insert sequential letters or numbers before the name when
registering each job button. Ex.) 01_xxxx
• If you enter a job button name that is two lines long, the job
button display will be two lines long.
Color of Job Button
• You can register up to 100 addresses to a job button.
• For the number mentioned above, the count for a group is the
number of addresses registered to the group (maximum of 99
addresses) plus the group name, so a group with 99
addresses registered to it is counted as having 100
addresses.
Scan Settings/Detailed settings
For details on Scan Settings/Detailed settings, see “Scan
Settings Overview” on p. 4-19.
E-mail settings
Specify a color for the job button.
When you select this Job Button
• Display Scan Setting Screen
Displays the Scan Setting screen when the job button is
pressed.
• Skip Scan Setting Screen
Starts scanning without displaying the Scan Setting
screen when the job button is pressed.
Subject
Enter a subject for the e-mail message.
Message
Enter the text of the e-mail message.
IMPORTANT
If you select [Skip Scan Setting Screen], scanning starts as
soon as the job button is pressed, whether a document is
inserted or not.
4-18
Delivery Options
Action when the same named file exists
Select the action to take when a file of the same name
exists at the destination.
• Display a message
Displays a message confirming that the file will be
overwritten.
• Abort sending
Cancels sending.
• Overwrite the file
Overwrites the identically named file without displaying
a confirmation message.
Send the files immediately after scanning
• ON
Starts sending when scanning completes.
• OFF
Starts sending after you confirm the scanned image when
scanning completes.
Index Settings
Specify whether to attach metadata (index files) to scanned
images.
❏ Scan Settings Overview
The scan settings include basic and detailed settings for
scanning parameters and individual settings by file format.
Scan Settings
4
Web Menu (User Mode)
Confirm addresses before sending
• ON
Displays the Address Confirmation screen, and then
starts sending after you confirm the address.
• OFF
Sends the image without confirming the address.
Screen after sending
Select the screen to display after an image is sent.
• Initial Screen
Returns to the startup screen set for [Screen after Login]
in the User Settings.
• Logout
Logs out after the images are sent.
• Select screen after sending
Displays a message dialog for selecting from the above
actions after the images are sent.
Page Size
Select the size of the document to scan from the list.
Hint
• The [Auto size] option automatically detects the size of the
scanned document during scanning.
• When scanning a long document, select [Auto size (Long)]
IMPORTANT
A resolution of [300 dpi] or more cannot be set when [Auto size
(Long)] is selected.
4-19
Mode
Select the scanning mode (Black and White, Error
Diffusion, Text enhance, Gray, Color, Auto Color
Detection).
When [Auto Color Detection] is selected, the scanner
automatically detects whether the document is color or
black and white. When this option is selected, you can also
configure the following settings.
• When [Text enhance] is selected, [Bleed-through reduction]
cannot be selected.
Resolution (dpi)
Select the scanning resolution (100, 150, 200, 300, 400, or
600 dpi).
Scanning Side
Select the method for scanning the document (Simplex,
Duplex, Skip blank page, Folio).
Hint
• Mode in case of binary
Specify the scanning mode to use when a black and white
document is detected.
• Threshold intensity to judge the document as color
Adjust the sensitivity to colors in a document.
• Aresize to judge the document as color
Specify the ratio of colored regions in a document.
IMPORTANT
TIFF
JPEG
PDF
Yes
No
Yes
Error Diffusion
Yes
No
Yes
Text enhance
Yes
No
Yes
Gray
No
Yes
Yes
Color
No
Yes
Yes
Auto Color Detection
No
No
Yes
4-20
IMPORTANT
• The scanning speed may be reduced when [Skip Blank Page]
is selected.
• A resolution of [400 dpi] or more cannot be set when [Folio] is
selected. In addition, [Double feed detection by Ultrasonic]
cannot be selected.
Prescan
• The [Auto Color Detection] function cannot be used
simultaneously with the color drop-out or prescan function.
• Depending on the selected mode, the file formats available for
saving may be limited. A warning message appears when an
unavailable combination is selected.
Black and White
• The Skip Blank Page option scans both sides of a document
and skips saving any image it determines to be a blank page.
• You can adjust the sensitivity of the Skip Blank Page option
under [Contents detection sensitivity].
• The initial value for the Skip Blank Page option is set to “90.”
As you lower the value from the default setting, pages of the
document with text become more likely to be skipped as well.
As you raise the value from the default setting, pages of the
document that are blank become less likely to be skipped.
Enables you to preview an image of the first page of the
document before scanning the entire document.
Hint
• Scanning pauses after the first page of the document is
scanned, and the image of the first page is displayed.
• Use the displayed image to confirm and adjust the brightness
and contrast. Press [Continue] to confirm the adjusted
brightness and contrast for the first image and continue
scanning.
File name
Specify a name for the image file to be sent.
Add Date to File name
PDF:
The scanner adds 17 digits that indicate the date and time
to the file name of the image to be sent.
Ex.) May 14, 2013, 3:40:30 p.m.
yyyymmdd: File name + 20130514154030123
mmddyyyy: File name + 05142013154030123
ddmmyyyy: File name + 14052013154030123
Configure the settings for compression ratio, multi page,
OCR (optical character recognition), and security.
* The last three digits indicate the number of milliseconds.
You can select [Custom] to configure additional file name
settings. The additional settings are identical to those in
“Custom File Name Settings” on p. 4-6.
When you select this Job Button
Specify whether the file name entry screen appears when
you start scanning using the job button.
File format
4
Compression Method
Specify a compression level by selecting [Standard] or
[High Compression] as the compression method.
TIFF: Multi page settings
OCR (Optical Character Recognition)
Select [Single page (Front/back separate file)] to save each
side of each page as a separate image file, [Single page
(Front/back same file)] to save each page as a separate
image file, or [Multi page] to save one image file
containing multiple pages when scanning multiple pages.
JPEG: Compression
When OCR is set to [ON], the scanner performs character
recognition on textual portions of the document, and
embeds the detected characters as editable text
information in the PDF file.
Hint
When you set OCR to [ON], make sure to select the OCR
language that matches the document text.
Encryption
Apply security to the PDF file.
IMPORTANT
Using the High (128-bit RC4) level setting is recommended. The
Low (40-bit RC4) level setting provides less security.
Protect Document
Select a compression ratio for images saved in JPEG
format.
The ability to view the document is protected by a
password.
IMPORTANT
Take care not to forget the password once it is set. If you forget
the password, the document can no longer be opened.
4-21
Web Menu (User Mode)
Select a file format for the image file, and configure the
corresponding settings.
Protect Permission
Brightness (Back)
Permissions for printing and editing the PDF file are
protected by a password.
Enables the PDF file to be printed from a printer.
Enabled for duplex scanning. Use this option when the
front and back sides of a document are shaded differently.
To change the brightness settings for the front and back
sides, clear the [Same as front] check box.
Changes allowed
Contrast (Front)
Enables editing of the PDF file, such as adding or deleting
pages.
Adjusts the contrast of the image to be scanned.
Contrast (Back)
Enable copying of text, images, and
accessibility
Enabled for duplex scanning. Use this option when the
front and back sides of a document are shaded differently.
To change the contrast settings for the front and back sides,
clear the [Same as front] check box.
Printing allowed
Enables text information embedded by OCR to be copied
and the PDF file to be read aloud by text-to-speech
software.
IMPORTANT
• Protecting PDF file permissions is recommended when the
permissions have been restricted.
• You can change the permissions and cancel password
protection for a password protected PDF file in an application
capable of editing PDF files such as Adobe Acrobat.
Detailed settings
Double feed detection by Ultrasonic (Only
available with the ScanFront 330)
The scanner uses an ultrasonic sensor to detect when two
or more documents are fed together, and stops feeding
when a double feed is detected.
IMPORTANT
• This method is effective when documents overlap by 1.97"
(50 mm) or more. It does not function if only a slight portion of
the document is overlapping.
• When [Scanning Side] is set to [Folio], [Double feed detection
by Ultrasonic] cannot be selected.
Double feed detection by length
The scanner detects by document length when two or more
documents are fed together, and stops feeding when a
double feed is detected.
IMPORTANT
Brightness (Front)
Adjusts the brightness of the image to be scanned.
4-22
• Using the length of the first document page as a reference, the
scanner detects a double feed when a subsequent page is
longer or shorter than the reference page by 1.38" (35 mm) or
more.
• Set [Double feed detection by length] to [OFF] when scanning
a document that contains pages of different lengths.
Document orientation
Color drop-out
Rotates the scanned image to the specified angle.
The color drop-out function has a “drop-out” effect that
leaves out a specified color (red, blue, or green) while
scanning, and a “color enhancement” effect that
emphasizes a specified color.
Hint
When [Auto] is selected, the scanner detects text orientation
within the document and rotates the image so that the
orientation of the text is correct.
IMPORTANT
The scanning speed may be reduced when [Auto] is selected.
Deskew
IMPORTANT
If you select [Prefer Quality], the scanning speed is reduced. If
you are scanning a large number of pages, select [Prefer
Speed] to prevent a decrease in scanning speed.
Bleed-through reduction
Eliminates bleed-through images, in which images on the
reverse side of a scanned document appear on the scanned
page, such as when scanning thin documents with text or
images on both sides.
Hint
The OCR recognition rate is sometimes improved by deleting
colored ruled lines and other objects with the color drop-out
function.
❏ Copying Job Buttons
You can copy the settings of a job button and register it as
a new job button.
As an example, this section describes how to copy from the
Shared Job Button to the My Job Button.
Hint
Use this function when you want to copy a job button between
the Shared Job Button and My Job Button or register it as a
different job button after changing some of the settings.
1. Select Shared Job Button for the [Job Button Type].
2. Select the job button you want to copy, and click
[Copy].
IMPORTANT
The bleed-through reduction setting is disabled when the
scanning mode is set to [Text enhance].
Hint
When using bleed-through reduction, adjust the bleed-through
reduction level to match the type of document.
4-23
4
Web Menu (User Mode)
Detects when a document has been fed askew from the
scanned image, and then straightens the image.
• Prefer Quality
Image processing is performed to minimize the loss of
quality of an image that has deteriorated as result of
deskewing.
• Prefer Speed
The image deteriorates slightly as a result of deskewing.
IMPORTANT
The color drop-out setting is disabled when the scanning mode
is set to [Color].
3. Select My Job Button for the copy destination, and
click [OK].
Exporting from the Scanner
You can save the job button settings file to a specified
folder.
1. Click [Export from ScanFront].
4. Confirm the copied job button.
2. Click [Save], specify a save location, and save the job
button settings file.
Importing to the Scanner
You can import a previously exported job button settings
file to the scanner.
❏ Editing Jobs
1. Click [Import to ScanFront].
You can edit the settings of a registered job by clicking
[Edit] in the job button list. The settings that can be edited
are identical to those in “Registering New Job Buttons” on
p. 4-18.
❏ Exporting and Importing Job Buttons
You can back up your job button data as a settings file in
DAT format, and import the backed up job button settings
file to another ScanFront unit.
Hint
If you have multiple ScanFront units, you can use the same job
buttons on all of them by importing the job button settings file
registered on one ScanFront unit to the other units.
4-24
2. Specify a previously exported job button settings file.
3. Select a processing method for importing the job
button settings file.
• Replaces the whole data: Deletes all currently
registered job buttons and overwrites them with the
imported job buttons.
• Appends data: Adds the imported job buttons to the
currently registered job buttons.
4. Click [Execute].
Confirm the message that appears, and click [OK] to
import the data.
Hint
When importing is completed, the following message appears.
Click [OK] to return to Job Button Settings and confirm the
imported job button.
4
Web Menu (User Mode)
4-25
4-26
Chapter 5 Troubleshooting
1. Troubleshooting ............................................... 5-2
1. Troubleshooting
If any of the following problems occurs, solve the problem as described in the corresponding solution.
Network, Web Menu
Cannot log in to the Web menu
Cannot use an LDAP address
book (certain users only)
Cause
Solution
Cause
Solution
Cause
Cannot update the settings in
the Web menu
Solution
Cause
Solution
Cause
Cannot access the Web menu
Cannot create a new folder
(shared folder/FTP server)
Specifying a mail address as the
address and then starting
scanning results in an error
Cannot edit the address book/
job buttons (certain users only)
Can only select certain
destinations. For example, can
only select shared folders
(certain users only)
Cannot connect to an FTP
server that can be accessed
from outside the company
5-2
JavaScript is disabled in the Web browser.
Enable JavaScript.
The administrator has set user function restrictions.
Contact the administrator of the ScanFront.
The ScanFront is being used or a user has not logged out.
Check the ScanFront status and then try again.
The Web browser has become unstable.
Delete the cache and cookies and reset the settings of the Web browser.
The IP address assigned from the DHCP server has changed.
Solution
Contact the administrator of the ScanFront, and check the IP address
assigned to the ScanFront.
Cause
Permission to write to the shared folder has not been granted for the
user name and password that were entered.
Solution
Cause
Solution
Cause
Solution
Cause
Solution
Cause
Solution
Contact the administrator of the shared folder.
The mail server settings have not been registered, or have been deleted.
Contact the administrator of the ScanFront.
The administrator has set user function restrictions.
Contact the administrator of the ScanFront.
The administrator has set user function restrictions.
Contact the administrator of the ScanFront.
The scanner cannot connect to an FTP server that requires firewall
settings to be configured.
Use an FTP server that does not require firewall settings to be
configured.
The wrong send time is
displayed for an e-mail message
received at the destination
The sender’s address is not
displayed at the destination of
an e-mail message
Cannot connect to the network
(IP address conflict problem)
Cannot connect to the network
(LAN cable connection problem)
Cannot connect to the network
(device name conflict problem)
Cause
(1) The date and time settings are incorrect. (2) The time zone is set to a
different country.
Solution
Contact the administrator, and check the “Language/Timezone” setting.
Cause
Solution
The IP address that was set is already being used by another device.
Solution
Contact the system administrator of the network, and change the IP
address setting.
Cause
The LAN cable is not connected properly.
Solution
Check the connections of the LAN cable.
Cause
The device name that was set is already being used by another device.
Solution
Contact the system administrator of the network, and change the device
name setting. When you install two or more ScanFront scanners, take
care to ensure duplicate device names are not set.
Cause
Cause
Cause
Solution
Cause
Cannot log in
Solution
Cannot browse shared folders
during address registration.
Cause
Solution
Data has been saved to the folder.
5
Contact the administrator of the shared folder.
Permission to change the shared folder has not been granted for the user
name and password that were entered.
Contact the administrator of the shared folder.
The administrator has set user function restrictions.
Contact the administrator of the ScanFront.
Uppercase and lowercase letters were not entered correctly.
(See p. 4-3 and p. 3-5.)
Enter the uppercase and lowercase letters for the user name and
password correctly.
You are attempting to browse folders on a computer running Windows 7
or Windows Server 2008 R2.
Enter the full path of the shared folder manually.
5-3
Troubleshooting
Solution
Cannot scan from the Home
screen (certain users only)
Contact the administrator, and register the e-mail addresses.
Cause
Solution
Cannot delete a folder
The e-mail addresses of the user and administrator have not been
registered.
Cause
Cannot send image files to
devices and folders on different
segments of the network.
Solution
A ScanFront Service Server does not exist on the network. (A
ScanFront Service Server has not been configured or is not running.)
Install ScanFront Service on a computer on the same network as the
scanner. If a ScanFront Service Server has been implemented, check the
necessary settings. In addition, you must start the ScanFront Service
Server before turning ON the ScanFront.
Scan
Cause
Streaks appear in images
Solution
Cause
Paper becomes jammed
Paper jams occur frequently
Solution
Cause
Solution
Cause
Documents are double fed
Solution
Cause
Solution
A stack of documents are fed
together
Scanning starts immediately
after I press a job button (certain
users only)
5-4
Cause
Solution
Cause
Solution
The scanning glass is dirty.
Refer to the ScanFront 300/300P/330 INSTRUCTIONS (electronic
manual) and clean the scanning glass. If there are scratches on a
scanning glass, contact your local authorized Canon dealer.
The rollers are dirty.
Refer to the ScanFront 300/300P/330 INSTRUCTIONS (electronic
manual) and clean the rollers.
The rollers (consumable parts) have worn out.
Contact the administrator of the ScanFront and then replace the rollers.
Static electricity is causing the pages of the document to stick to each
other.
Before you load a stack of documents, fan the documents.
The type of paper of the documents is causing a paper feed error.
Load no more than ten pages of documents. (See p. 2-10.) Use bypass
feeding to scan the pages one by one.
The feed selection lever is set to Page Separation OFF. (See p. 2-5.)
Set the feed selection lever to page separation feeding.
The job buttons are designed to work that way. See “Skip Scan Setting
Screen” on p. 4-18.
Place the document and then press a job button.
Hardware
Cause
Cannot turn on the power
Solution
The scanner does not turn ON
when the power switch is
pressed.
Cause
Solution
The AC adapter is not connected properly or the power plug is not
inserted.
Check the connections of the AC adapter and power plug. If the
problem is not resolved after checking the connections, contact your
local authorized Canon dealer.
A USB memory device in inserted in the scanner.
Remove the USB memory device, and restart the scanner.
5
Troubleshooting
5-5
5-6
Chapter 6 Index
1. Index ................................................................ 6-2
1. Index
A
F
AC Adapter ................................................................... 1-7
Address
Copying .......................................................3-22, 4-14
Modifying ............................................................. 3-22
New ..............................................................3-19, 4-11
Address Book Settings .................................................. 4-9
Address Selection Screen ............................................ 3-11
Address Type
E-mail ..........................................................3-19, 4-11
Fax ........................................................................ 4-13
FTP Server ...................................................3-20, 4-11
Group ...........................................................3-21, 4-13
Shared Folder ...............................................3-19, 4-12
Feed Selection Lever .....................................................2-5
Feed Tray .......................................................................2-4
File Formats ....................................................... 3-29, 4-21
Flow Up Until Sending an Image File ...........................3-2
H
Handling ........................................................................1-3
Home Screen .................................................................3-7
I
Index Settings ...................................................... 4-7, 4-19
Installation Location ......................................................1-2
Introduction .......................................................................i
J
Job Button Screen ..........................................................3-7
Job Button Settings ............................................ 4-16, 4-18
Address Settings ....................................................4-18
Delivery Options ...................................................4-18
Detailed Settings ...................................................4-18
E-mail Settings ......................................................4-18
Scan Settings .........................................................4-18
C
Card ............................................................................... 2-3
Conceptual Diagram of the ScanFront .............................. i
Copying Job Buttons ................................................... 4-23
Custom File Name Settings .......................................... 4-6
D
Delivery Options ......................................................... 3-31
Detailed Settings ................................................3-26, 4-22
Device Authentication ...........................................3-4, 4-3
Disposal ........................................................................ 1-5
Documents .................................................................... 2-2
Double Feed Error ........................................................ 2-9
E
Eject Tray ...................................................................... 2-4
Exporting and Importing Address Books ................... 4-14
Exporting and Importing Job Buttons ......................... 4-24
6-2
K
Key in Type Login .........................................................3-6
L
List Type Login .............................................................3-5
Loading Mark ................................................................2-7
Lock Lever ...................................................................2-10
Logging In to the Web Menu ........................................4-3
Login Screen
Key in Type .............................................................3-4
List Type .................................................................3-4
Server Authentication ..............................................3-4
M
W
Moving the Scanner ...................................................... 1-3
N
Names and Functions of Parts ...................................... 1-6
Web Menu
User Mode ...............................................................4-2
Web Menu Overview ....................................................4-2
P
Paper Jam ...................................................................... 2-9
Placing a Card ............................................................... 2-8
Placing a Folded Document .......................................... 2-7
Placing a Long Document ............................................ 2-7
Placing Documents ....................................................... 2-6
Plain Paper .................................................................... 2-2
Preparing the Scanner ................................................... 2-4
R
Registering New Job Buttons ..................................... 4-18
S
Safety Instructions ........................................................ 1-2
Scan Settings ...................................................... 3-25, 4-19
Basic Condition Settings ...................................... 3-25
Detailed Settings .................................................. 3-26
Scan/Delivery Options ................................................ 3-24
Scanning ..................................................................... 3-15
Security Settings ......................................................... 3-30
Server Authentication ............................................ 3-4, 4-3
6
T
Index
Troubleshooting ............................................................ 5-2
Turning Off the Power .................................................. 3-3
Turning On the Power .................................................. 3-3
U
USB Memory .............................................................. 3-13
USB Memory Screen .................................................. 3-13
USB Port ....................................................................... 2-5
User Settings ................................................................. 4-4
User Settings Screen ..................................................... 3-8
Change Password ................................................... 3-8
6-3
CANON ELECTRONICS INC.
1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN
CANON U.S.A. INC.
ONE CANON PARK, MELVILLE, NY 11747, U.S.A.
CANON CANADA INC.
6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA
CANON EUROPA N.V.
BOVENKERKERWEG 59, 1185 XB AMSTELVEEN, THE NETHERLANDS
CANON LATIN AMERICA, INC.
703 WATERFORD WAY, SUITE 400 MIAMI, FLORIDA 33126, U.S.A.
CANON AUSTRALIA PTY. LTD.
1 THOMAS HOLT DRIVE, NORTH RYDE, SYDNEY. N.S.W, 2113. AUSTRALIA
CANON SINGAPORE PTE. LTD.
1 HARBOUR FRONT AVENUE #04-01, KEPPEL BAY TOWER, SINGAPORE 098632
CANON HONGKONG COMPANY LTD.
19TH FLOOR, THE METROPOLIS TOWER, 10 METROPOLIS DRIVE, HUNGHOM, KOWLOON, HONG KONG.
CANON KOREA BUSINESS SOLUTIONS INC.
168-12 SAMSEONG-DONG, GANGNAM-GU, SEOUL, KOREA
CANON INDIA PVT. LTD
7TH FLOOR, TOWER B DLF CYBER TERRACES DLF PHASE III GURGAON - 122002 HARYANA, INDIA
PUB. CE-IE-0919
© CANON ELECTRONICS INC. 2013