Canon imageRUNNER ADVANCE 6255 Operation Guide

Basic Operation Guide
After you finish reading this guide, store it in a safe place for future reference.
ENG
How to Use This Manual
How to Use This Manual
This manual describes the following functions, operations, and maintenance procedures.
•
•
•
•
•
Functions that can be operated from the touch panel display of the machine
Remote UI functions that can operate the machine from a computer
Printing from a computer
Routine Maintenance Procedures
Clearing paper jams/staple jams
Store this manual next to the machine so it can be used when the user encounters trouble operating the machine.
* Some functions explained in this manual may require optional equipment.
* Screen shots used in this manual may differ from the ones you actually see.
Contents
■ Before You Start Using This Machine
What This Machine Can Do• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •10
Main Power and Energy Saver Key• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •12
Parts and Their Functions • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •14
Control Panel and Touch Panel Display • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •17
Main Menu Screen Settings • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •20
Changing Settings According to Your Needs • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •22
■ Flow of Basic Operations
How to Make a Copy• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •24
Things You Can Do with the Copy Functions • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •26
Sending a Fax • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •30
Things You Can Do with the Fax Functions • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •32
Sending Scanned Data (E-Mail/I-Fax/File Servers) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •36
Things You Can Do with the Scan and Send Functions • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •38
Storing Scanned Data • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •42
Things You Can Do with the Scan and Store Functions • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •44
Printing Stored Data • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •46
Sending Stored Data• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •48
Things You Can Do with the Access Stored Files Functions (File Operation)• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •50
Things You Can Do with the Access Stored Files Functions (Print) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •51
Things You Can Do with the Access Stored Files Functions (Send) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •54
Operating the Machine from a Computer (Remote UI) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •56
Printing from a Computer • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •58
■ Routine Maintenance
Loading Paper • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •62
Replacing the Stamp Cartridge (Duplex Color Image Reader Unit-G1)• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •83
Replacing the Staple Cartridge (For Optional Products) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •86
Removing Punch Waste (External 2/3 Hole Puncher-A1) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •92
Replacing the Toner Cartridge • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •94
Routine Cleaning • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •99
Consumables• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •108
2
How to Use This Manual
■ Troubleshooting
Clearing Paper Jams • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •112
Reducing the Frequency of Paper Jams • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •162
Clearing Staple Jams (For Optional Products)• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •163
If Memory Becomes Full During Scanning • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •169
When an Error Message Is Displayed • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •171
When an Error Code Is Displayed• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •172
Printer/Fax Driver Troubleshooting • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •173
Service Call Message• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •174
Frequently Asked Questions • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •180
3
How to Use This Manual
Refer to the following manuals included with your machine according to your needs.
●
Before Using This Machine
■ Describes precautions for using the machine.
Before Using This Machine
■ Includes the specifications of the machine.
Read this guide first.
Please read this guide before operating this product.
After you finish reading this guide, store it in a safe place for future reference.
●
ENG
Setup Guide
■ Describes the settings required before using functions, such as the
network settings for sending e-mail.
Setup Guide
■ Describes how to add applications and update the firmware.
After you finish reading this guide, store it in a safe place for future reference.
●
ENG
Basic Operation Guide (This Manual)
■ Provides an overview of the functions and describes the basic
operations.
Basic Operation Guide
■ Describes the maintenance and troubleshooting procedures for the
machine.
After you finish reading this guide, store it in a safe place for future reference.
4
ENG
How to Use This Manual
●
e-Manual
■ Describes all the functions of the machine. Also provided with a
search function that is useful for finding and checking information.
■ Includes “Practical Workflows,” which introduces flows of practical
operations using functions of the machine.
●
Driver Installation Guide
■ Provides instructions on installing the printer, fax, and other drivers.
• Printer Driver Installation Guide
• Mac Printer Driver Installation Guide
• Fax Driver Installation Guide
• Network ScanGear Installation Guide
■ Included on the same CD-ROM as each driver.
Symbols Used in This Manual
The following symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions that
should be observed for safety.
Indicates a warning concerning operations that may lead to death or injury to persons if not performed
correctly. To use the machine safely, always pay attention to these warnings.
Indicates a caution concerning operations that may lead to injury to persons if not performed correctly.
To use the machine safely, always pay attention to these cautions.
Indicates operational requirements and restrictions. Be sure to read these items carefully to operate the
machine correctly, and avoid damage to the machine or property.
Indicates a clarification of an operation, or contains additional explanations for a procedure. Reading
these notes is highly recommended.
Indicates an operation that must not be performed. Read these items carefully, and make sure not to
perform the described operations.
5
How to Use This Manual (e-Manual)
●
Follow the procedure below to install the e-Manual.
● Windows
1. Insert the e-Manual CD-ROM into your computer.
2. Select the language for the e-Manual.
3. Select [Install].
If you select [Display Manuals], the e-Manual is displayed without installation.
4. Read the License Agreement, and then click [Yes].
The e-Manual is saved in the [Documents]* folder on your computer. If the shortcut icon is created on the Desktop or if the [index. html] file is
double-clicked, the e-Manual is displayed.
* The folder name differs, depending on your operating system. The folder name is [Documents] if you are using Windows Vista/7 and [My Documents] if you
are using Windows 2000/XP.
● Macintosh
1. Insert the e-Manual CD-ROM into your computer.
2. Drag-and-drop the [iRADV_6275_Manual_us] folder to the location you want to save it.
3. Double-click the index.html file inside the [iRADV_6275_Manual_us] folder to display the e-Manual.
• Depending on the operating system you are using, a security protection message may appear. In this case, allow the content to be
displayed.
• When you start the e-Manual, the following page (the top page) appears.
■ If the e-Manual (CD-ROM) Does Not Start
The CD-ROM auto run function may be disabled. In this case, perform the following procedure.
• Windows 7
1. Click [Start] on the task bar  click [Computer].
2. Double-click the e-Manual icon.
3. Double-click [Maninst.exe].
• Windows XP/Vista
1. Click [Start] on the taskbar  click [My Computer].
2. Double-click the e-Manual icon.
3. Double-click [Maninst.exe].
• Windows 2000
1. Double-click [My Computer] on the desktop.
2. Double-click the e-Manual icon.
3. Double-click [Maninst.exe].
6
4
5
How to Use This Manual
3
6
1
7
2
8
12
1
2
8
Enter keyword(s) here
Enter a keyword in the search dialog box, and press
search results page is displayed.
. The
Select from functions
The instructions of each function and operation method are described.
3
[Top]
The top page of the e-Manual is displayed.
4
[Site map]
The site map of the e-Manual is displayed.
5
[Help]
The usage of the e-Manual is displayed.
6
11
10
9
Select from purpose
This section includes the introduction of functions of the machine for
each purpose.
9
[Office Locations]
Inquiries for the machine are displayed.
10
[Trademarks]
The trademarks are displayed.
11
[Copyright]
The information of copyrights is displayed.
12
[Disclaimers]
The disclaimers are displayed.
[Glossary]
The glossary is displayed.
7
First of all…
This section describes the required information to use the machine,
and the information of optional product and software.
■ Performing a Search
Enter a keyword in the entry field which is located at the top of the “Top page” or on the search area in the “Topic page,” and then click
to display the search results.
■ Printing a Topic Page
• On a topic page, you can print by category or by topic.
• Depending on the settings of the Web browser, the background color and images of the topic page may not be printed.
7
MEMO
8
What This Machine Can Do
Before You Start Using This
Machine
1
What This Machine Can Do . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Main Power and Energy Saver Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Parts and Their Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
External View• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 14
Internal View • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 16
Control Panel and Touch Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Main Menu Screen Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Changing Settings According to Your Needs . . . . . . . . . . . . . . . . . . . . . . . . 22
9
Before You Start Using This Machine
What This Machine Can Do
Revolutionary Documentation Work with an Evolving Multitasking
Machine
Send Outside
the Company Fax
Original
Color Scan
Function
Fax
Function
1
2
3
4
Copy
Function
Send
Function
Telephone Line
I-Fax
Internet
MEAP
Function
E-Mail
Copy/Print
1
2
Print
Function
LAN
Remote UI
Function
3
4
In-Company
Computer
File Server
E-Mail
The imageRUNNER ADVANCE 6275/6265/6255 incorporates a rich array of input and output features that can greatly enhance your efficiency. Equipped
with features that meet the needs of document work in a digitized office, the imageRUNNER ADVANCE 6275/6265/6255 represents the ultimate in a digital
multitasking machines.
● Copy
● Fax
You can make two-sided copies from one-sided originals or copy two
pages onto one side of the paper to reduce printing cost. There are
other modes, such as the Collate modes. (p. 24)
Scanned documents as well as stored files and computer data can be
sent by facsimile. You can also send documents to multiple addresses
and forward received facsimile to another destination. Also, by using
Remote Fax sending function, you can share the Fax function on the
same network. (p. 30)
10
You can send scanned documents by e-mail or I-fax, as well as store
them on a network file server. You can also store sent documents in
the Mail Box. (p. 36)
● Use Memory Media
You can scan and store documents in the memory media connected to
the USB port. You can also print stored files directly from the memory
media. (p. 42, p. 46)
● Use Mail Box (Store/Print/Send)
● Use Advanced Box
You can store scanned documents or data from a computer in a mail
box. You can print documents stored in a mail box, and sent them to
other destinations. (p. 42, p. 46)
You can set a file format to the scanned document so that it can be
accessed from your computer. You can also store files in the Advanced
Box with a file format that can be used on your computer.
The stored data can be shared by accessing it from a computer.
The Advanced Box can also be accessed from other imageRUNNER
ADVANCE machines for operations, such as printing stored data. (p. 42,
p. 46)
● Use Remote Scanner
● Print Secured File
You can use this machine as a remote scanner by TWAIN compatible
computer software. You can scan up to 11” x 17” in size at a resolution
of 600 x 600 dpi. (See e-Manual > Scanner.)
You can send print data protected with a PIN/password from a
computer to the machine. This data can be printed only by entering
the correct PIN/password on the machine. This enables you to print
without unauthorized people viewing your data. (See e-Manual >
Secure Print.)
● Printing a Fax/I-Fax File in the Memory RX
inbox
● View Web Page
If Memory RX is set, files received by Fax/I-Fax function are not printed,
but stored in the Memory RX Inbox. You can print the stored files
whenever necessary. This can help prevent outputs being forgotten at
the machine. (See e-Manual > Fax/I-Fax Inbox.)
You can use this machine to browse Web pages from the touch panel
display of the machine or print PDF files on the Web pages. (See
e-Manual > Web Access.)
* Some functions explained in this manual may require optional equipment.
11
Before You Start Using This Machine
● Send Documents (E-Mail/Fax/I-Fax/File
Server/Store in Mail Box)
Main Power and Energy Saver Key
This section describes how to use the main power switch and the Energy Saver key.
Do not connect or disconnect the power cord with wet hands, as this may result in electrical
shock.
● How to Turn ON the Main Power
Make sure that the power plug is firmly inserted into the power outlet, and then turn ON the main power of the machine following the
procedure below.
1.
2.
3.
Open the main power switch cover.
Press the main power switch to the “I” side.
Close the main power switch cover.
• If you are using a login service, log in using the procedure for the login
service you are using.
• If the main power indicator on the control panel does not light even
though the main power switch is ON, be sure to check the breaker to see
if it is OFF.
• If you want to turn OFF the main power and then back ON again, wait for
at least 10 seconds after the main power indicator is turned OFF before
turning ON the main power.
12
Before You Start Using This Machine
● Shutting Down the Machine
This machine performs a procedure to protect hard disk when the machine is shut down. This enables the machine to be shut down safely, even
if there are any jobs being processed, or a MEAP application is running while the machine is shutting down.
1.
2.
3.
Open the main power switch cover.
Press the main power switch to the “
Close the main power switch cover.
” side.
• Do not turn the main power OFF while using the Fax/I-Fax function.
Sending or receiving I-fax or fax documents cannot be done when the
main power is turned OFF.
• If the message <Backing up stored data from the Remote UI...> is
displayed on the touch panel display, do not turn the main power OFF.
This may cause the machine to fail to back up the stored data.
• Data stored in the machine may be damaged if the Advanced Box is
accessed by another imageRUNNER ADVANCE machine or a computer
immediately before the machine shuts down.
• The machine may take some time to completely shutdown. Do not
unplug the power cord until the main power indicator of the machine is
OFF.
• If the main power is turned OFF during scanning or printing, a paper jam
may occur.
• If you set [Quick Startup Settings for Main Power] to ‘On’ in [Preferences]
(Settings/Registration), the tone sounds when turning OFF the main
power of the machine. (Depending on the situations, the machine does
not startup quickly and the tone does not sound.)
● Energy Saver Key
If the machine is idle for a certain period of time, the machine will enter the Auto Sleep mode to minimize energy consumption. Press
(Energy Saver) to cancel the Sleep mode and resume normal machine operations.
Control Panel (Flat)
Upright Control Panel-B1
13
Parts and Their Functions
This section provides you with the names and functions of all the parts on the outside and inside of the main unit.
External View
The Copy Tray-Q1 and Duplex Color Image Reader Unit-G1 are attached:
2
1
3
4
5
6
7
11
8
10
9
14
Before You Start Using This Machine
13
12
14
15
16
17
1
Control Panel
Includes the keys, touch panel display, and indicators required for
operating the machine. (See “Control Panel and Touch Panel Display,”
on p. 17.)
10
11
2
USB Port (1)
Use the USB port to connect a USB device.
3
LAN Port
Use a LAN cable to connect the machine to a network.
4
USB Connector
Use a USB cable to connect the machine to a computer.
5
USB Port (2)
Use the USB port to connect external hard disks and other devices to
the machine.
6
Multi-Purpose Tray
Use the multi-purpose tray to feed paper manually, and for loading
nonstandard paper stock.
7
Main Unit’s Upper Right Cover
Open this cover when clearing a paper jam inside the main unit.
Paper Drawer 3, 4
Holds up to approximately 550 sheets of paper (20 lb bond (80 g/m2))
or 680 sheets of paper (17 lb bond (64 g/m2)).
Paper Drawer 1, 2 (Right/Left)
Holds up to approximately 1,500 sheets of paper (20 lb bond (80 g/
m2)) or 1,700 sheets of paper (17 lb bond (64 g/m2)).
12
LINE 1
Use this port to connect a fax line to the machine.
13
LINE 4
Holds up to approximately Use this port to connect the Super G3
3rd/4th Line Fax Board to the machine.
14
LINE 3
Holds up to approximately Use this port to connect the Super G3
3rd/4th Line Fax Board to the machine.
15
LINE 2
Use this port to connect the Super G3 2nd Line Fax Board to the
machine.
16
Breaker
Detects excess current or leakage current.
8
Main Unit’s Lower Right Cover
Open this cover when clearing a paper jam inside the main unit.
17
Test Button
Press this button to periodically test the circuit breaker.
9
Main Power Switch
Press to the “I” side to turn the power ON. (See “Main Power and Energy
Saver Key,” on p. 12.)
15
Parts and Their Functions
Internal View
The Copy Tray-Q1 and Duplex Color Image Reader Unit-G1 are attached:
1
2
3
1
Toner Replacement Cover
Open this cover to replace the toner cartridge.
2
Front Cover
Open this cover to clear a paper jam in the fixing transport unit.
16
3
Fixing Transport Unit
Pull the fixing transport unit out to clear a paper jam.
Control Panel and Touch Panel Display
This section provides you with the names and functions of all the parts of the control panel and touch panel display.
Before You Start Using This Machine
2
1
20
19
3
4
5
6
18
7
8
17
1
16
15
Energy Saver key
Press to set or cancel the Energy Saver mode/Sleep mode. Lights when
the machine enters the Energy Saver mode/Sleep mode.
2
USB Port
Use the USB port to connect a USB device.
3
Settings/Registration key
Press to specify settings/registration.
4
Counter Check key
Press to display the copy and print count totals on the touch panel
display.
5
Clear key
14 13
6
12
11
10
9
Stop key
Press to stop a job in progress, such as a scan, copy, or fax (scanning
only) job.
7
Start key
Press to start an operation.
8
Edit Pen
Use when operating the touch panel display, such as to enter
characters. If you lose the edit pen, contact your local authorized
Canon dealer. Do not use an object with a sharp end on the control
panel, such as a pencil or ballpoint pen, in place of the edit pen.
9
Main Power Indicator
Lights when the main power is turned ON.
Press to clear entered values or characters.
17
Control Panel and Touch Panel Display
10
Error Indicator
Flashes or lights if there is an error in the machine. When the Error
indicator flashes, follow the instructions that appear on the touch
panel display. When the Error indicator maintains a steady red light,
contact your local authorized Canon dealer.
11
Brightness Adjustment Dial
17
Volume Settings key
Press to display the screen for adjusting settings, such as the
transmission volume and fax sending/receiving alarm volume.
Processing/Data Indicator
Flashes or blinks green when the machine is performing operations,
and maintains a steady green light when fax data is stored in memory.
12
16
Use to adjust the brightness of the touch panel display.
Reset key
18
Status Monitor/Cancel key
Press to check the status of jobs or to cancel print jobs. Also, press to
check status of the machine, such as checking the amount of paper
remaining.
Press to restore the standard settings of the machine.
19
13
ID (Log In/Out) key
Press to log in/out when a login service such as Department ID
Management or SSO-H has been set.
14
Numeric keys
Press to enter numerical values.
15
Touch Panel Display
The settings screen for each function is shown on this display. Eight
function keys are displayed by default.
18
Quick Menu key
Press to retrieve favorite functions stored in Quick Menu. Also, if you
are using authentication, Quick Menu set for each individual user can
be displayed.
20
Main Menu key
Press to return to the Main Menu screen, such as when you want to
switch functions.
Before You Start Using This Machine
● Use Quick Menu
If functions that are frequently used are set in the Quick Menu beforehand, you can recall the function
by pressing
(Quick Menu). If you are using a login service, Quick Menu screen set for each user
appears. To register a function in the Quick Menu, set the function and press [Register to Quick Menu]
from
.
● Logging In/Out
If you are managing the machine with a login service, such as Department ID Management or SSO-H
(Single Sign-On H), a log in screen appears. If the log in screen appears, enter the Department ID and
PIN or the user name and password  press
(Log In/Out) or [Log In] on the screen. Press
(Log
In/Out) or [Log Out] after you finish using the machine to log out.
● Use Help
If
(Help) is displayed on the top right of the function setting
screen, press
(Help) to check the explanation of the function
or how to specify settings. Press to check the explanation of the
function or how to specify settings.
19
Main Menu Screen Settings
You can specify settings for the displayed screen by pressing
an administrator.
on the top right of the screen. To perform this procedure, log in to the machine as
• The items displayed when
is pressed may differ, depending on the function.
• If authentication function is used, items displayed may differ or
may not be
available, depending on the login user’s privileges.
● Specifying the Main Menu Settings
You can set the number of buttons and the layout displayed on the Main Menu screen.
1. Press
 [Main Menu Button Display Settings].
2. Press
or
to select the number of buttons and the layout to be displayed.
3. Select the function that appears on the list  change the order in which it is displayed.
4. Press [OK].
• Select the function that appears on the list and press [Up] or [Down] to change the order
in which it is displayed.
• You can place or delete one blank button space by pressing [Add Blank] or [Delete Blank],
respectively.
Example of Customized Screen
● Top Buttons Settings
You can display up to two function shortcut buttons on the top of the screen.
1. Press
 [Top Buttons Settings].
2. Select the shortcut button and the function to assign to it.
3. Press [OK].
If you do not want to select a function, press [Unassigned].
Example of Registration
20
Before You Start Using This Machine
● Setting the Main Menu Wallpaper
You can select the wallpaper for the Main Menu screen.
1. Press
 [Main Menu Wallpaper Settings].
2. Select the wallpaper.
3. Press [OK].
Example of Customized Screen
● Other Main Menu Settings
You can set whether the shortcut buttons for modes, such as changing the displayed language or
changing the paper settings for copying/printing are displayed on the Main Menu screen.
1. Press
 [Other Main Menu Settings].
2. Specify the other settings.
3. Press [OK].
If <Display [Language/Keyboard Switch]> is set to ‘On’,
screen.
appears on the Main Menu
If <Display [Settings/Reg.Shortcut]> is set to ‘On’, [Settings/Reg.Shortcut] appears on the
Main Menu screen.
From [Settings/Reg.Shortcut], you can select shortcut buttons to the setting screens for
[Auto Adjust Gradation], [Paper Settings], and [Paper Type Management Settings].
Example of Customized Screen
If <Display [Show All]> is set to ‘On’, [Show All] appears on the Main Menu screen.
For more information on [Language/Keyboard Switch], [Auto Adjust Gradation], [Paper
Settings], and [Paper Type Management Settings], see e-Manual > Settings/Registration.
21
Changing Settings According to Your Needs
The Settings/Registration screen appears when you press
(Settings/Registration) on the control panel.
The machine provides various settings that enable you to use it more conveniently and easily. You can register or change the settings according to your
needs. For more information, see e-Manual > Settings/Registration.
●
Preferences
You can specify basic settings for using the machine, such as changing the paper size to load, changing the default screen to display, setting the date
and time, setting the time it takes to enter the low power mode, and specifying the settings for connecting to a network.
●
Adjustment/Maintenance
You can specify settings for using the machine more comfortably, such as adjusting the density, adjusting the gradation, and cleaning the feeder.
●
Function Settings
You can specify and register settings for using each function more conveniently, such as registering shortcut buttons for the Copy function, setting
automatic redialing for the Fax function, and setting the maximum data size to send via e-mail.
●
Set Destination
You can register fax and e-mail destinations in the address book. In addition to registering frequently used destinations, you can also register multiple
destinations as a group, enabling you to send to those destinations at the same time. You can also register different types of destinations (e-mail and
file server) as a group.
●
Management Settings
You can set the administrator settings for managing the machine. This enables you to set an ID and password for each department, manage
confidential information, and count the number of pages printed for each ID. You can also register licenses and certificates.
22
Flow of Basic Operations
Flow of Basic Operations
2
How to Make a Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Things You Can Do with the Copy Functions . . . . . . . . . . . . . . . . . . . . . . . . 26
Sending a Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Things You Can Do with the Fax Functions . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Sending Scanned Data (E-Mail/I-Fax/File Servers) . . . . . . . . . . . . . . . . . . . 36
Things You Can Do with the Scan and Send Functions . . . . . . . . . . . . . . . 38
Storing Scanned Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Things You Can Do with the Scan and Store Functions . . . . . . . . . . . . . . . 44
Printing Stored Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Sending Stored Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Things You Can Do with the Access Stored Files Functions
(File Operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Things You Can Do with the Access Stored Files Functions (Print) . . . . 51
Things You Can Do with the Access Stored Files Functions (Send) . . . . 54
Operating the Machine from a Computer (Remote UI) . . . . . . . . . . . . . . . 56
Printing from a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
23
How to Make a Copy
This section describes the flow of basic copy operations.
An optional product is required to use the Copy function.
1
2
Placing Originals
Place the original on the feeder or the platen glass.
Placing originals in the feeder
Selecting Function
Select [Copy] from the Main Menu screen.
Press [Copy].
Adjust the slide guides to fit the size of your originals. Neatly place
your originals with the side to be copied face up.
Copy Basic Features Screen is displayed.
Placing originals on the platen glass
Open the feeder/platen cover.
Place your originals face down.
You can set various copying functions. For more
information, see from p. 26 to p. 29 in this manual.
Gently close the feeder/platen cover.
• If a log in screen for Department ID Management or SSO-H appears, you must enter the applicable authentication information (ID, password/
PIN). If the Copy Card Reader-F1 is attached, first insert a control card.
• If a login service, such as Department ID Management or SSO-H has been set, press
(Log In/Out) to log out.
24
3
4
Enter the number of copies.
Press the numeric keys to enter the desired copy quantity (1 to 999).
If you make a mistake when entering values, press
(Clear) enter the correct value.
Start Copying
After specifying the settings, press
Press
Flow of Basic Operations
Setting the Number of Copies
(Start).
(Start).
If the following screen appears, press
(Start) to
scan the next original. After all of the originals are
scanned, press [Start Copying].
The specified copy quantity appears on the screen,
as shown below.
When copying is complete, remove your originals.
25
Things You Can Do with the Copy Functions
To use Copy functions, press [Copy] on the Main Menu screen. This section describes the functions you can use on the Copy Basic Features
screen and the [Options] (1/3) screen. The [Options] screen is divided into three screens. Pressing
or
on the bottom right of the
screen displays the next or previous screen. An optional product is required to use the Copy function.
3
2
4
5
1
6
8
7
8
Regular Copy Basic Features Screen
1
2
3
4
[Direct]/[Copy Ratio]
You can specify the copy ratio for a copy job. You can change
the zoom ratio by reducing/enlarging a scanned document to
a preset paper size, or by entering a value to specify a desired
scan ratio.
6
[Select Paper]
You can select the paper size/type and the paper source.
You can also set the machine to automatically recognize the
original size and the copy ratio, and then copy.
7
[Favorite Settings]
You can register frequently used copy settings. You can recall
the registered frequently used settings for future use.
[Previous Settings]
You can recall the three most recent copy jobs, and make
copies using the recalled copy settings.
Shortcuts to [Options]
Press to select a [Options] mode. [Finishing], [2-Sided],
[Density], and [Original Type] are set as default.
[Copy Sample]
You can check the copy result of one set before making
multiple sets of copies. You can also copy a specified page.
[Check Settings]
You can check, edit, or clear the current copy settings.
Quickly Make Settings and Copy
You can set the settings on the Regular Copy Basic
Features screen quickly by using the Express Copy
Basic Features screen. For instructions on displaying
the Express Copy Basic Features Screen, see e-Manual >
Settings/Registration.
26
5
8
[Interrupt]
You can temporarily stop the current copy job and give
priority to a rush copy.
3
1
4
Flow of Basic Operations
2
12
11
5
6
10
9
8
7
[Options] 1/3
1
[Book
2 Pages]
7
2
3
[2-Sided]
You can make one-sided copies from two-sided originals, or
make two-sided copies of your originals.
8
9
[Booklet]
You can layout the scanned documents to make a booklet.
You can also print a cover sheet or make a saddle stitch
booklet.
10
6
[Insert Sheets]
Press to insert blank sheets or chapter pages between
specified pages.
11
[N on 1]
You can reduce multiple pages of the original to copy onto a
single page. You can also change the order of the page layout.
[Transparency Cover Sheets]
The machine automatically interleaves a sheet of
paper between each transparency when copying onto
transparencies.
[Job Build]
You can scan originals that are too many to be placed at once,
by dividing them into multiple batches. After all originals are
scanned, copying is started.
* To make a saddle stitch booklet, optional products are required.
5
[Different Size Originals]
You can make copies of different size originals at the same
time without separating the documents. If the paper setting is
set to Auto, the machine automatically selects the appropriate
paper size.
* To staple printed sheets, optional products are required.
4
[Density]
Change the exposure. You can press
to make the
exposure darker or
to make the exposure lighter. You
can set the machine to automatically adjust the exposure.
[Finishing]
You can collate copies in page order or into groups of the
same page.
You can staple the printed sheets.
[Original Type]
Image quality for scanning is adjusted according to the type
of original, such as [Text/Photo], [Printed Image], [Photo
Printout], or [Text].
You can copy facing pages in a book onto separate sheets of
paper.
12
[Add Cover]
You can add covers.
27
Things You Can Do with the Copy Functions
This section describes the functions you can use on the [Options] (2/3 and 3/3) screen of the Copy function. The [Options] screen is
divided into three screens. Pressing
or
on the bottom right of the screen displays the next or previous screen. An optional
product is required to use the Copy function.
2
1
10
12
11
9
3
5
4
10
8
7
9
6
5
[Options] 2/3
1
2
3
4
5
[Secure Watermark]
You can embed hidden text, such as “CONFIDENTIAL” in the
background of copies. The embedded text appears when the
copies are printed, helping prevent unauthorized copying and
information leakage.
7
[Document Scan Lock]
You can embed tracking information in copies. This increases
security by preventing unauthorized copies.
8
[Erase Frame]
This mode enables you to erase shadows that appear when
scanning various types of originals. You can also erase
shadows of the punch holes.
9
[Print Date]
You can copy the date (day, month, and year) onto the output.
You can specify the size, position, or direction of the date.
[Watermark]
This mode enables you to copy a watermark and user-defined
text onto the output. You can specify the size, position, or
direction of the watermark.
[Page Numbering]
You can copy with page numbers. You can also specify the
size, position, or direction of the page number.
[Copy Set Numbering]
This mode enables you to print copy set numbers. You can
specify the size, position, or direction of the copy set number.
[Gutter]
This mode enables you to make copies with the entire original
image shifted by a designated width to create a margin on the
copies. You can set different width values for the each side of
the paper.
[Shift]
This mode enables you to make copies with the entire image
shifted to the center or a corner. You can use the numeric keys
to specify the location.
Functions with this mark require an optional product(s).
28
6
10
[Sharpness]
This mode enables you to adjust image quality for copying.
You can use this mode when you want to soften and sharpen
text, lines, or the outline of the image.
How to Make a Copy
3
1
4
10
5
Flow of Basic Operations
2
6
9
8
7
[Options] 3/3
1
2
3
4
5
[Print & Check]
This mode enables you to confirm scanned images page by
page before copying when you scan originals on the platen
glass.
[Nega/Posi]
6
7
This mode enables you to copy the original image with the
hues and gradations inverted.
[Repeat Images]
This mode enables you to repeatedly copy the entire original
image in either the vertical or horizontal direction.
[Merge Job Blocks]
This mode enables you to scan multiple batches of originals
with different copy settings and copy them as one document.
[Print on Tab]
This mode enables you to copy onto the tabs on tab paper.
8
9
10
[Cascade Copy]
This mode enables you to print copies from the machine and
a cascade copy printer.
[Superimpose Image]
This mode superimposes an image (image form) previously
scanned, registers it in the memory of the machine, and then
places it on the image of the original.
[Store in Mail Box]
You can store the scanned originals in the User Inbox. The
specified copy mode is also stored.
[Job Done Notice]
Press to have the machine notify the user through e-mail
when the copy job is done.
[Mirror Image]
This mode enables you to copy the original image reversed, as
if it were a reflection in a mirror.
29
Sending a Fax
This section describes the flow of basic fax operations.
An optional product is required to use the Fax function.
2
1
Placing Originals
Place the original on the feeder or the platen glass.
Placing originals in the feeder
Selecting Function
Select [Fax] from the Main Menu screen.
Press [Fax].
Adjust the slide guides to fit the size of your originals. Neatly place
your originals with the side to be copied face up.
Fax Basic Features screen is displayed.
Placing originals on the platen glass
Open the feeder/platen cover.
Place your originals face down.
You can set various facsimile functions. For more
information, see from p. 32 to p. 35 in this manual.
Gently close the feeder/platen cover.
• If a log in screen for Department ID Management or SSO-H appears, you must enter the applicable authentication information (ID, password/
PIN). If the Copy Card Reader-F1 is attached, first insert a control card.
• If a login service, such as Department ID Management or SSO-H has been set, press
(Log In/Out) to log out.
• The send settings for the last send job may be retained.
- To cancel the settings, press
(Reset).
- The specified destinations are not retained.
30
3
4
Enter the fax number.
Enter the fax number using the numeric keys.
If you want to enter two or more fax numbers, press
[OK]  enter the next destination.
You can specify the destination using the
one-touch buttons or [Address Book]. For more
information on storing the destination, see
e-Manual > Fax.
Start Sending the Fax
After specifying the settings, press
Press
Flow of Basic Operations
Specify the destination.
(Start).
(Start).
If the following screen appears, press
(Start)
to scan the next original. After all of the originals
are scanned, press [Start Sending].
When sending is complete, remove your originals.
After a job is sent, the send settings may be
retained except the specified destinations.
(Reset).
To cancel the settings, press
To send other jobs with the same settings,
specify destinations for the jobs as the
destination specified for the previous job is not
retained.
31
Things You Can Do with the Fax Functions
To use the Fax functions, press [Fax] on the Main Menu screen. This section describes the main functions on the Fax Basic Features screen. An
optional product is required to use the Fax function.
4
5
3
6
2
7
1
8
13
12
11
10
9
Fax Basic Features Screen
1
2
3
4
5
6
32
[Details]
You can check the detailed information for the destination
selected from the Address Book. You can also change the new
destination.
[Delete Dest.]
You can delete the displayed destination.
7
8
[Tone]
Resolution
If the resolution is high, you can send fine text and images
clearly. If the resolution is low, the data size becomes smaller
and you can reduce the time it takes to send.
Scan Size
You can select the original scanning size. If you press [Auto],
the machine automatically recognizes the size of the original
when scanning.
Press when you want to directly call an extension line that is
connected to a PBX (Private Branch eXchange) which accepts
only tone signals. If you press [Tone], the letter <T> appears.
9
[PIN Code]
10
[Direct Send]
11
[On-Hook]
12
[Address Book]
13
One-Touch Buttons
Press to enter the PIN (Personal Identification Number) code.
You can press this key only if [Option] is selected for PIN code
position. If [Prefix], [Suffix], or [Off ] is selected for PIN code
position, this key is grayed out.
[To Remote Add. Book]
You can specify destinations registered in the one-touch
buttons of a server machine by accessing from a client
machine on the network.
[Previous Settings]
You can recall the three most recent destinations or fax
settings. You can send a fax using the recalled destination or
settings.
Register One-Touch Button
Press to register destinations in one-touch buttons.
Check that the recipient can receive the facsimile, and then
start scanning the originals. You can directly send without
storing the original in the memory.
When using the fax information service, you can perform
operation, such as entering number while listening to the
automated audio response from the speaker of the machine.
Press to select a destination from the Address Book. You can
also register frequently used destinations in the Address Book.
Press to recall the destinations stored in a one-touch button.
1
4
3
Screen for Specifying the Fax Destination
1
2
[Pause]
Press to insert a pause of several seconds in the fax number
that you are dialing. If you insert a pause, the letter <p>
appears between the numbers, and the letter <P> appears
at the end of the number. When dialing an overseas number,
insert a pause after the country code, and at the end of the
telephone number.
[Backspace]
3
4
[Set Details]
Displayed when multiple lines are set to be used. Press to set
the subaddress and password, or to select the telephone line
to use for transmission.
[Subaddress]
You can send or receive fax documents with increased
security by attaching a subaddress and a password to your fax
transactions.
Press when you enter an incorrect number to delete the
number before the cursor.
Functions with this mark require an optional product(s).
33
Flow of Basic Operations
2
Things You Can Do with the Fax Functions
This section describes the functions you can use on the [Options] (1/2 and 2/2) screen of the Fax function. The [Options] screen is divided
into two screens. Pressing
or
on the bottom right of the screen displays the next or previous screen. An optional product is required
to use the Fax function.
2
3
1
4
12
11
5
6
10
9
8
7
[Options] 1/2
1
[Original Type]
Image quality for scanning is adjusted according to the type
of original, such as [Text], [Map], or [Photo].
8
[Sender Name (TTI)]
You can register a department name or personal name in
advance, and show this on the destination fax machine.
* Set the Sender Name after specifying the destination.
2
3
[2-Sided Original]
Set to send two-sided originals. You can select [Book Type] or
[Calendar Type].
[Book
2 Pages]
You can scan facing pages, such as in a book one sheet at a
time.
4
5
6
7
34
9
10
[Density]
11
[Sharpness]
12
[Copy Ratio]
[Different Size Originals]
You can scan originals of different size fed together in one
group.
[Erase Frame]
This mode enables you to erase shadows that appear when
scanning various types of originals. You can also erase
shadows of the punch holes.
[Direct Send]
Check that the recipient can receive the facsimile, and then
start scanning the originals. You can directly send without
storing the original in the memory.
[Select Line]
You can select the telephone line to use for sending a
facsimile.
[Job Build]
You can scan originals that are too many to be placed at once,
by dividing them into multiple batches. After all originals are
scanned, sending is started.
Change the exposure. You can press
to make the
exposure darker or
to make the exposure lighter. You
can set the machine to automatically adjust the exposure.
This mode enables you to scan the originals with a sharper
or softer contrast. You can use this mode when you want to
soften and sharpen text, lines, or the outline of the image.
Specify the desired zoom ratios. You can change the zoom
ratio by reducing/enlarging a scanned document to a preset
paper size, or by entering a value to specify a desired scan
ratio.
Functions with this mark require an optional product(s).
3
1
4
Flow of Basic Operations
2
[Options] 2/2
1
2
[Delayed Send]
This mode enables you to store a send job in memory, and
have it sent at a later time.
[Preview]
This mode enables you to preview the scanned data of your
originals and to check the page count before sending a fax.
You can also delete a specified page.
3
4
[Finished Stamp]
You can print a stamp (approximately 1/8” (3 mm) in diameter)
on the front side of scanned and sent originals.
[Job Done Notice]
Press to have the machine notify the user through e-mail
when the fax job is done.
35
Sending Scanned Data (E-Mail/I-Fax/File Servers)
This section describes the flow of basic scan and send operations.
Depending on the file format, optional products are required to use the Scan function.
1
2
Placing Originals
Place the original on the feeder or the platen glass.
Placing originals in the feeder
Selecting Function
Select [Scan and Send] from the Main Menu screen.
Press [Scan and Send].
Adjust the slide guides to fit the size of your originals. Neatly place
your originals with the side to be copied face up.
Scan and Send Basic Features screen is displayed.
Placing originals on the platen glass
Open the feeder/platen cover.
Place your originals face down.
You can set various send functions. For more
information, see from p. 38 to p. 41 in this manual.
Gently close the feeder/platen cover.
• If a log in screen for Department ID Management or SSO-H appears, you must enter the applicable authentication information (ID,
password/PIN). If the Copy Card Reader-F1 is attached, first insert a control card.
• If a login service, such as Department ID Management or SSO-H has been set, press
(Log In/Out) to log out.
• The send settings for the last send job may be retained.
- To cancel the settings, press
(Reset).
- The specified destinations are not retained.
36
3
4
Press [Address Book]  select destination  press [OK].
Press [Address Book].
If you are sending to only one destination, select a destination. If you
are sending to multiple destinations, select the destinations  press
[OK].
Start Sending
After specifying the settings, press
Press
Flow of Basic Operations
Specify the Destination
(Start).
(Start).
If the following screen appears, press
(Start)
to scan the next original. After all of the originals
are scanned, press [Start Sending].
For more information on storing the destination
in the address book, see e-Manual > Scan and
Send.
When sending is complete, remove your originals.
You can specify the destination using the onetouch buttons or frequently used settings. Also,
if you want to send to a new destination not
yet stored, press [New Destination]  enter the
destination.
After a job is sent, the send settings may be
retained except the specified destinations.
(Reset).
To cancel the settings, press
To send other jobs with the same settings,
specify destinations for the jobs as the
destination specified for the previous job is not
retained.
37
Things You Can Do with the Scan and Send Functions
To use the Send functions, press [Scan and Send] on the Main Menu screen. This section describes the main functions on the Scan and
Send Basic Features screen. Depending on the file format, optional products are required to use the Scan function.
2
3
1
3
6
5
4
Scan and Send Basic Features Screen
1
2
3
38
[Address Book]
Press to select a destination from the Address Book. You
can also register frequently used e-mail, I-fax, or file server
destinations in the Local Address Book.
[One-Touch]
If a frequently used destination is stored in a one-touch
button, you can specify the destination quickly. Press [To
Remote Add. Book] to specify destinations registered in the
one-touch buttons of a server machine by accessing from a
client machine on the network.
[New Destination]
Press to specify a new destination not stored in the Address
Book or one-touch buttons.
4
5
6
[Send to Myself]
You can specify your own e-mail address as the destination.
The administrator can restrict general users to send e-mail
only to their addresses.
[Specify Destinations]
Press to display the methods for specifying destinations or the
destination list.
[Personal Folder]
You can specify your personal folder as the destination. The
administrator can restrict destination for file transmission to
the operator’s personal folder.
Flow of Basic Operations
1
2
3
4
5
6
9
7
8
Scan and Send Basic Features Screen (Destination Set)
1
2
3
4
5
[Previous Settings]
You can recall the three most recent destinations or send
settings. You can send using the recalled destination or
settings.
[Favorite Settings]
You can register frequently used destination and settings. You
can recall the registered frequently used settings for future
use.
[Select Color]
You can select the Full Color, Grayscale, or Black-and-White
mode. You can also set the machine to automatically select a
color mode according to the original.
[Resolution]
If the resolution is high, you can send fine text and images
clearly. If the resolution is low, the data size becomes smaller
and you can reduce the time it takes to send.
6
7
8
9
[File Format]
If you are sending to an e-mail address or file server, you can
specify the file format. You can select from PDF, XPS, OOXML
(pptx), JPEG, or TIFF.
[Cc Bcc]
In addition to the destination for the documents, you can
specify e-mail address destinations for the Cc and Bcc
addresses.
[Delete Dest.]
You can delete the selected destination from the destination
list.
[Details]
You can check the detailed information for the destination
selected from the destination list. You can also change the
new destination.
[Scan Size]
You can select the original scanning size. If you press [Auto
Size], the machine automatically recognizes the size of the
original when scanning.
39
Things You Can Do with the Scan and Send Functions
This section describes the functions you can use on the [Options] (1/2 and 2/2) screen of the Scan and Send function. The [Options] screen
is divided into two screens. Pressing
or
on the bottom right of the screen displays the next or previous screen. Depending on the file
format, optional products are required to use the Scan function.
2
3
1
4
5
9
8
7
6
[Options] 1/2
1
2
3
[Original Type]
Image quality for scanning is adjusted according to the type
of original, such as [Text], [Map], or [Photo].
6
[2-Sided Original]
Set to send two-sided originals. You can select [Book Type] or
[Calendar Type].
[Book
7
2 Pages]
You can scan facing pages, such as in a book one sheet at a
time.
8
4
5
40
[Different Size Originals]
You can scan originals of different size fed together in one
group.
[Erase Frame]
This mode enables you to erase shadows that appear when
scanning various types of originals. You can also erase
shadows of the punch holes.
9
[Copy Ratio]
Specify the desired zoom ratios. You can change the zoom
ratio by reducing/enlarging a scanned document to a preset
paper size, or by entering a value to specify a desired scan
ratio.
[Sharpness]
This mode enables you to scan the originals with a sharper
or softer contrast. You can use this mode when you want to
soften and sharpen text, lines, or the outline of the image.
[Job Build]
You can scan originals that are too many to be placed at once,
by dividing them into multiple batches. After all originals are
scanned, sending is started.
[Density]
Change the exposure. You can press
to make the
exposure darker or
to make the exposure lighter. You
can set the machine to automatically adjust the exposure.
Useful Send Functions (Last Page)
3
1
4
Flow of Basic Operations
2
5
8
7
6
7
[Options] 2/2
1
2
3
4
[Delayed Send]
This mode enables you to store a send job in memory, and
have it sent at a later time.
[Preview]
This mode enables you to preview the scanned data of your
originals and to check the page count before sending your
document. You can also delete a specified page.
5
6
7
[Finished Stamp]
You can print a stamp (approximately 1/8” (3 mm) in diameter)
on the front side of scanned and sent originals.
[Job Done Notice]
Press to have the machine notify the user through e-mail
when the send job is done.
8
[E-Mail Priority]
You can set a priority level when sending e-mail.
[Reply-to]
You can specify a reply-to address when sending an e-mail or
I-fax.
[Subject/Message]
You can specify a subject and enter a message when sending
an e-mail or I-fax. If you do not specify a subject, it will be
specified automatically.
[File Name]
If you set PDF(OCR), XPS(OCR), or OOXML(OCR) as the file
format, you can set [Auto (OCR)] to ‘On’ to automatically
extract the first text block in the document for use as its
filename.
41
Storing Scanned Data
This section describes the flow of basic Scan and Store operations. It also describes an example of how to store scanned data in a mail
box. Depending on the file format, optional products are required to use the Scan function.
1
2
Placing Originals
Place the original on the feeder or the platen glass.
Placing originals in the feeder
Selecting Function
Select [Scan and Store] from the Main Menu screen.
Press [Scan and Store].
Adjust the slide guides to fit the size of your originals. Neatly place
your originals with the side to be copied face up.
Select [Mail Box] from the screen where you can select the type of
storage location.
Placing originals on the platen glass
Open the feeder/platen cover.
Place your originals face down.
Gently close the feeder/platen cover.
• If a log in screen for Department ID Management or SSO-H appears, you must enter the applicable authentication information (ID, password/
PIN). If the Copy Card Reader-F1 is attached, first insert a control card.
• If a login service, such as Department ID Management or SSO-H has been set, press
(Log In/Out) to log out.
42
3
4
Specify the mail box that you want to store the file in.
Select the desired mail box.
Start Scanning
After specifying the settings, press
Press
Flow of Basic Operations
Select Storage
(Start).
(Start).
You may need to enter a PIN when specifying the mail box.
Press [Scan].
If the following screen appears, press
(Start)
to scan the next original. After all of the originals
are scanned, press [Start Storing].
The Scan screen is displayed.
You can set various scan functions. For more
information, see from p. 44 to p. 45 in this
manual.
When scanning is complete, remove your originals.
43
Things You Can Do with the Scan and Store Functions
To scan the original and store it, press [Scan and Store] on the Main Menu screen. This section describes the functions you can use on the
Scan and Store Basic Features screen and the [Options] screen. If you press [Scan] after selecting the storage location, the screen below
appears. Depending on the file format, optional products are required to use the Scan function.
3
2
4
1
5
6
11
7
10
9
8
Scan Screen
1
2
3
4
5
6
44
[Select Color]
You can select the Full Color or Black mode. You can also set
the machine to automatically select a color mode according
to the original.
[Resolution]
7
8
If the resolution is high, you can store fine text and images
clearly. If the resolution is low, the data size becomes smaller.
[Direct]/[Copy Ratio]
9
This mode enables you to change the copy ratio by enlarging/
reducing a copy to a preset paper size, or by entering a value
to specify a desired copy ratio.
[Scan Size]
You can select the original scanning size. If you press [Auto],
the machine automatically recognizes the size of the original
when scanning.
[File Format]
[Restore Default Set.]
This mode is useful if you want to clear all settings and reset
the settings. All settings are cleared.
[2-Sided Original]
Set to scan two-sided originals. You can select [Book Type] or
[Calendar Type].
[Density]
Change the exposure. You can press
to make the
exposure darker or
to make the exposure lighter. You
can set the machine to automatically adjust the exposure.
10
[File Name]
11
[Original Type]
You can specify a file name for the data to be scanned.
Image quality for scanning is adjusted according to the type
of original, such as [Text/Photo], [Printed Image], [Photo
Printout], or [Text].
You can set a file format, such as a PDF format to the scanned
document so that it can be accessed from your computer.
[Favorite Settings]
You can register frequently used scan settings. You can recall
the registered frequently used settings for future use.
The available functions may differ, depending on the storage
location.
3
1
4
8
5
7
Flow of Basic Operations
2
6
[Options]
1
2
3
4
5
[Book
2 Pages]
You can scan facing pages, such as in a book one sheet at a
time.
[Booklet Scan]
You can scan with booklet settings.
6
7
[N on 1]
You can scan multiple pages of the original and reduce the
size of the images to fit onto a single page. You can also
change the order of the layout.
8
[Nega/Posi]
This mode enables you to scan and record the original image
by inverting the hues and gradations.
[Job Build]
You can scan originals that are too many to be placed at once,
by dividing them into multiple batches. After all originals are
scanned, storing is started.
[Different Size Originals]
You can scan originals of different size fed together in one
group.
[Erase Frame]
This mode enables you to erase shadows that appear when
scanning various types of originals. You can also erase
shadows of the punch holes.
[Sharpness]
This mode enables you to adjust image quality for copying.
You can use this mode when you want to soften and sharpen
text, lines, or the outline of the image.
The available functions may differ, depending on the storage
location.
45
Printing Stored Data
This section describes the flow of basic Access Stored Files operations. The procedure for printing files stored in a mail box is used here
as an example.
1
2
Selecting Function
Select [Access Stored Files] from the Main Menu screen.
Press [Access Stored Files].
Select Storage
Specify the storage location for the file.
Select [Mail Box] from the Storage Selection screen.
Select the desired mail box.
You may need to enter a PIN when specifying the mail box.
• If a log in screen for Department ID Management or SSO-H appears, you must enter the applicable authentication information (ID, password/
PIN). If the Copy Card Reader-F1 is attached, first insert a control card.
(Log In/Out)to log out.
• If a login service, such as Department ID Management or SSO-H has been set, press
46
3
4
Select the file that you want to print  press [Print].
Select the file to print.
Start Printing
Flow of Basic Operations
Select File
After specifying the settings, press [Start Printing].
Press [Start Printing].
Press [Print].
You can set various print settings on the screen
displayed when [Change Print Settings] is pressed.
For more information, see from p. 51 to p. 53 in this
manual.
The Print screen is displayed.
When printing is complete, the display returns to the
Mail Box Selection screen.
47
Sending Stored Data
This section describes the flow of basic Access Stored Files operations. The procedure for sending a file stored in a mail box is used here
as an example.
1
2
Selecting Function
Select [Access Stored Files] from the Main Menu screen.
Press [Access Stored Files].
Select Storage
Select [Mail Box].
Select [Mail Box] from the Storage Selection screen.
Select the desired mail box.
You may need to enter a PIN when specifying the mail box.
• If a log in screen for Department ID Management or SSO-H appears, you must enter the applicable authentication information (ID, password/
PIN). If the Copy Card Reader-F1 is attached, first insert a control card.
(Log In/Out) to log out.
• If a login service, such as Department ID Management or SSO-H has been set, press
48
3
4
Select the file that you want to send  press [Send].
Select the file to send.
Start Sending
Flow of Basic Operations
Select File
Specify the destination  press [Start Sending].
Press [Address Book].
Select the destinations  press [OK].
Press [Send].
Press [Start Sending].
You can set various send functions. For more
information, see p. 54 to p. 55 in this manual.
49
Things You Can Do with the Access Stored Files Functions (File Operation)
To perform various operations on stored files, press [Access Stored Files] on the Main Menu screen. This section describes the functions
you can use to edit files stored in a mail box. Select the file that you want to edit from the list of stored files, press [Edit File], and the
following screen is displayed.
2
10
9
1
3
8
7
6
5
15 14
4
File Selection Screen
1
2
3
4
5
6
7
8
[Clear Selection]
9
[Delete]
You can delete stored files. You can erase unnecessary files
and arrange the storage location.
10
[Merge Multiple Files]
11
[Insert Pages]
12
[Delete Pages]
13
[Add Files (Scan and Store)]
14
[Change File Name]
15
[Move/Duplicate]
Press to select view settings of the files stored in a mail box.
[Print List]
You can print a list of files stored in a mail box.
12 11
Edit File Screen
Press to cancel the selection of a file. For a mail box, if you
cancel a selection, this switches to [Select All (Max 100 Files)].
List/Thumbnail
13
[Print]
You can combine multiple files in the mail box into one file.
Then you can print the combined files as one file.
You can insert a specified file from the mail box in front of the
specified page of another file from the same mail box.
Press to display the Print Settings screen.
[Send]
Press to send a file stored in the mail box.
[Edit File]
Press to display the menu for adding or deleting a file, or
displaying the detailed information of a file.
[Display Image]
This mode enables you to preview the stored file and check
the page count.
[Details]
This mode enables you to erase specified page from a file that
is stored in a mail box.
You can scan the original and store the new file in the selected
storage location.
You can change a file name.
You can move or duplicate files stored in the mail box.
You can check the detailed information of the stored file.
The available functions may differ, depending on the storage
location.
50
Things You Can Do with the Access Stored Files Functions (Print)
This section describes the functions on the Print Settings screen that you can use when printing stored files. If you select the file that
you want to print from the list of stored files and press [Print], the following screen is displayed. Optional products are required to
print PDF/XPS files.
4
13
5
1
6
7
12
11 10
9
8
Print Screen
Print Settings Screen
1
2
3
4
5
6
7
8
[Select Paper]
You can select the paper size/type and the paper source. You
can also set the machine to automatically select the paper size
to match the size of the stored original.
[Print Sample]
9
* Displayed only when print settings have not been changed.
10
You can check the print result of one set before making
multiple sets of prints. You can also print a specified page.
[Restore Settings]/[Change Print Settings]
You can change or restore the print settings.
Press to store the print settings.
11
[2-Sided Printing]
12
[Finishing]
This mode enables you to print successive pages of a stored
file on both sides of a sheet of paper.
You can collate prints in page order or into groups of the same
page. You can staple the printed sheets.
* To staple printed sheets, optional products are required.
[Merge Files and Print]
Press to merge multiple files and print as one file. This key is
displayed only when multiple files are selected.
[Store Settings]
* Displayed only when using the Mail Box. Cannot be used when
multiple files are selected.
[Favorite Settings]
This mode enables you to register frequently used print
settings. You can recall the registered frequently used settings
for future use.
[Change No. of Copies]
Press to set the number of prints when multiple files are
selected.
13
Print Range
You can set the print range using [All Pages] or [Specify Pages].
[Delete File After Printing]
Press to have a file automatically deleted after it is printed.
[Restore Default Set.]
Press to cancel all settings.
[Start Printing]
Press to start printing.
The available functions may differ, depending on the storage
location.
51
Flow of Basic Operations
3
2
Things You Can Do with the Access Stored Files Functions (Print)
This section describes the functions you can use on the [Options] (1/2 and 2/2) screen of the Access Stored Files function. The [Options]
screen is divided into two screens. Pressing
or
on the bottom right of the screen displays the next or previous screen.
2
13
3
1
4
12
5
11
6
10
9
8
7
[Options] (Mail Box)
1
2
3
[Add Cover]
You can add covers.
8
[Insert Sheets]/[Job Separator]
Press to insert blank sheets or chapter pages between
specified pages. When multiple files are selected, job
separator sheets are inserted.
9
5
6
7
10
[Secure Watermark]
11
[Document Scan Lock]
12
[Superimpose Image]
13
[Print on Tab]
[Shift]
You can embed hidden text, such as “CONFIDENTIAL” in the
background of prints. The embedded text appears when the
copies are printed, helping prevent unauthorized copying and
information leakage.
You can shift the position of the image to print to the desired
position.
[Gutter]
This mode enables you to print with the entire original image
shifted by a designated width to create a margin on the prints.
You can set different width values for the each side of the
paper.
[Print Date]
This mode enables you to print the date onto the output. You
can specify the size, position, or direction of the date.
[Watermark]
This mode enables you to print a watermark and user-defined
text onto the output. You can specify the size, position, or
direction.
Functions with this mark require an optional product(s).
52
[Page Numbering]
You can print with page numbers. You can also specify the
size, position, or direction of the page number.
[Booklet]
You can layout the files to print a booklet. You can also print a
cover sheet or make a saddle stitch booklet.
* To make a saddle stitch booklet, optional products are required.
4
[Copy Set Numbering]
This mode enables you to print copy set numbers. You can
specify the size, position, or direction of the copy set number.
You can embed tracking information in prints. This increases
security by preventing unauthorized copies.
This mode superimposes an image (image form) previously
scanned, registers it in the memory of the machine, and then
combines it with the file to print.
Load tab paper in the paper drawer, and you can print onto
the tabs using the Print on Tab mode.
3
1
4
8
7
6
Flow of Basic Operations
2
9
5
11
10
[Options]
(Advanced Box, the Advanced Box of Another Machine on the Same Network, Memory Media)
1
[Resolution]
If the resolution is high, you can print fine text and images
clearly.
7
[Booklet]
This mode enables you to print documents in such a way that
the prints are made into a booklet.
* To make a saddle stitch booklet, optional products are required.
2
3
4
5
6
[Halftones]
You can select the adjustment methods to use when printing
with halftones.
[Match Paper Size]
You can enlarge/reduce a file image to match the paper size.
[Enlarge Print Area]
You can set the blank borders at each side of the page to 0” (0
mm), and print all the way to the edges of the page.
[Password to Open a Doc.]
You can print password protected PDF files by entering the
password required to open them.
8
9
[N on 1]
You can scan a file with multiple pages and reduce the size of
the pages to print onto a single page. You can also specify the
order in which to print.
[Enlarge/Reduce]
You can set the machine to enlarge or reduce data from JPEG
or TIFF image files to fit the desired paper size.
10
[Print Position]
11
[Image Orientation]
You can select whether to print JPEG and TIFF image data
centrally or in the top left, or specify to set the print position
automatically.
You can set the machine to compare the size of JPEG and
TIFF image data and automatically change the orientation of
the image to fit the desired paper size, or you can specify the
orientation of the image manually for printing.
[Print Comments]
You can print the PDF file and all the comments.
The available functions may differ, depending on the file format.
53
Things You Can Do with the Access Stored Files Functions (Send)
This section describes things you can do when sending a file stored in a mail box, and the modes available on the [Options] screen. Select the
file that you want to send from the list of stored files, press [Send], and the following screen is displayed. An optional product is required to
use the Fax function.
3
2
8
1
9
6
10
7
11
12
5
4
Send Basic Features Screen (Access
Stored Files)
1
2
3
4
5
6
54
[Address Book]
Press to select a destination from the Address Book. You can
also register frequently used e-mail, I-fax, file server, or fax
destinations in the Local Address Book.
[One-Touch]
If a frequently used destination is stored in a one-touch
button, you can specify the destination quickly. Press [To
Remote Add. Book] to specify destinations registered in the
one-touch buttons of a server machine by accessing from a
client machine on the network.
Screen for Specifying the Destination
(Access Stored Files)
7
8
9
[Details]
You can check the detailed information for the destination
selected from the address list. You can also change a new
destination.
File Format
If you are sending to an e-mail address or file server, you
can specify the file format. You can select from PDF, XPS,
OOXML(pptx), JPEG, or TIFF.
[Delete File After Sending]
Press to delete certain pages from a file.
[New Destination]
This mode enables you to specify a new destination not stored
in the Address Book or one-touch buttons.
10
[Delete Dest.]
[Send to Myself]
11
[Cc Bcc]
12
[Start Sending]
You can specify your own e-mail address as the destination.
The administrator can restrict general users to send e-mail
only to their addresses.
[Specify Destinations]
Press to display the methods for specifying destinations or the
destination list.
[Personal Folder]
You can specify your personal folder as the destination. The
administrator can restrict destination for file transmission to
the operator’s personal folder.
Press to delete a destination displayed in the destination list.
Press to specify e-mail address destinations for the Cc and Bcc
addresses.
Press to start sending.
3
1
4
Flow of Basic Operations
2
5
7
6
7
[Options]
1
2
3
4
[Delayed Send]
This mode enables you to store a send job in memory, and
have it sent at a later time.
[Job Done Notice]
5
6
Press to have the machine notify the user through e-mail
when the send job is done.
[File Name]
If you set PDF(OCR), XPS(OCR), or OOXML(OCR) as the file
format, you can set [Auto (OCR)] to ‘On’ to automatically
extract the first text block in the document for use as its file
name.
7
[E-Mail Priority]
You can set a priority level when sending e-mail.
[Reply-to]
You can specify a reply-to address when sending an e-mail or
I-fax.
[Subject/Message]
You can specify a subject and enter a message when sending
an e-mail or I-fax. If you do not specify a subject, it will be
specified automatically.
[Sender Name (TTI)]
You can register a department name or personal name in
advance, and show this on the destination fax machine.
* Set the Sender Name after specifying the destination.
55
Operating the Machine from a Computer (Remote UI)
The Remote UI (User Interface) is preinstalled software in the machine that enables you to access the machine’s functions by using your
computer’s Web browser. For example, the Remote UI enables you to access the machine to check job status, execute jobs, and specify various
settings.
To be able to use the Remote UI, all you need is a Web browser and a
network connection between your computer and the machine.
The Remote UI Is Useful in the Following Situations:
●
●
●
If you want to check the job status
If you want to edit Address Book from your computer
If you want to check the remaining amount of paper or toner from your seat
■ To enable the Remote UI:
• Log in as the administrator  specify the following settings.
1. Press
(Settings/Registration).
2. Press [Management Settings]  [License/Other]  [Remote UI].
3. Press [On]  [OK].
4. Turn OFF the main power of the machine, and then turn ON the main power again.
• The [Remote UI] setting is made effective only after turning the machine’s main power OFF, and then ON. For instructions on turning
ON/OFF the machine, see p.12, 13 in this manual.
56
Remote UI (Last Page)
1
2
Access the Remote UI from a Web browser.
Enter the IP address of the machine in the address bar of the Web
browser.
Checking the Job Status and Specifying
the Settings
Flow of Basic Operations
Accessing the Remote UI from a Web
Browser.
Check the job status and specify the settings.
To check the job status:
Click [Status Monitor/Cancel].
Press [ENTER] on the keyboard.
To login as the administrator, enter the System
Manager ID and System PIN  click [Administrator
Login].
To specify the settings:
Click [Settings/Registration].
To login as a general user, click [General User Login].
If the Log In screen is displayed, enter the user name
and password  click [Log In].
If a login service, such as Department ID
Management or SSO-H has been set, enter the
appropriate login information.
57
Printing from a Computer
If you install a printer driver in your computer, you can use the machine to print data created using application software. This section describes
the flow of basic operations to print data from your computer.
1
2
Display Print Settings Screen
Select [Print] from the [File] menu.
From the [File] menu in the application software, click [Print].
Display Properties Screen of Printer
Driver
Select the printer to use.
Select the printer to use in [Printer]  click [Properties].
The print dialog box is displayed.
The properties screen of the printer driver appears.
The default setting for [Print Style] is [2-sided
printing]. However, for some driver versions,
[1-sided printing] is the default setting.
• Printing methods may differ, depending on the applications you are using. For details, see the instruction manuals provided with the
application software.
• The screens may differ, depending on the operating system, and the type and version of the printer driver you are using.
58
* A printer driver is software required for printing from application software.
3
4
Specify the print settings.
Specify the desired settings  click [OK].
Start Printing
Flow of Basic Operations
Specify Print Settings
After specifying the settings, click [OK].
Click [OK].
When printing is complete, collect the output.
To display detailed descriptions for each print
setting, click [Help] on the bottom right of the
Properties screen.
The print job status can be checked from the
Remote UI. For more information, see p. 57 in
this manual.
59
MEMO
60
Routine Maintenance
Routine Maintenance
3
Loading Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Loading Paper into a Paper Drawer • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 62
Adjusting a Paper Drawer to Hold a Different Paper Size• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 66
Loading Pre-Punched Paper • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 68
Loading Transparencies • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 68
Loading Tab Paper Using the Tab Feeding Attachment Kit-B1 (Optional) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 69
Loading Paper into the Paper Deck Unit-A1/Paper Deck Unit-D1 (Optional) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 72
Loading Paper into the Document Insertion/Folding Unit-H1/Document Insertion Unit-L1 (Optional) • • • • • • • • • • • • • • • • • • • • • • • • • • • 81
Replacing the Stamp Cartridge
(Duplex Color Image Reader Unit-G1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Replacing the Staple Cartridge (For Optional Products) . . . . . . . . . . . . . 86
Replacing the Staple Cartridge in the Stapler Unit (Staple Finisher-P1/Booklet Finisher-P1) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 86
Replacing the Staple Case in the Saddle Stitcher Unit (Booklet Finisher-P1) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 89
Removing Punch Waste (External 2/3 Hole Puncher-A1) . . . . . . . . . . . . . 92
Replacing the Toner Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Routine Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Platen Glass and Underside of the Feeder • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 99
Manual Feeder Cleaning • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 100
Automatic Feeder Cleaning • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 104
Wire Cleaning • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 105
Drum Cleaning • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 106
Cleaning the Touch Panel Display • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 107
Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
61
Loading Paper
This section describes how to load paper.
Loading Paper into a Paper Drawer
If the selected paper runs out, or the selected paper drawer runs out of paper during printing, a screen prompting you to load
paper appears on the touch panel display.
Follow the procedure below to load paper into the paper drawers.
When handling paper, take care not to cut your hands on the edges of the paper.
• A screen prompting you to load paper also appears if the selected paper drawer is not fully inserted into the machine. Make
sure that the paper drawer is properly in place.
• Do not load the following types of paper into the Paper Drawer (Right/Left). Doing so may cause a paper jam.
•
•
•
•
•
•
•
•
•
•
Severely curled or wrinkled paper
Thin straw paper
Heavy paper (more than 80 lb cover (220 g/m2))
Paper which has been printed on using a thermal transfer printer
The reverse side of paper which has been printed on using a thermal transfer printer
Coated paper
Transparencies
Tracing paper
Tab paper
Labels
• Do not load the following types of paper into the Paper Drawer 3 and 4. Doing so may cause a paper jam.
•
•
•
•
•
•
•
•
•
Severely curled or wrinkled paper
Thin straw paper
Heavy paper (more than 80 lb cover (220 g/m2))
Paper which has been printed on using a thermal transfer printer
The reverse side of paper which has been printed on using a thermal transfer printer
Coated paper
Transparencies
Tracing paper
Labels
• Make sure that you fan the sheets of paper well before placing them. Thin paper, recycled paper, pre-punched paper, heavy
paper, and tab papers should be fanned particularly well before loading it.
• Never place paper or any other items in the empty part of the drawer next to the paper stack. Doing so may cause paper jams.
• When you are printing in the Staple mode, do not remove the output sheets that are waiting to be stapled. (Printing and
stapling resume after you clear the paper jam.)
• Register the size and type of the loaded paper in [Paper Settings] in [Preferences] (Settings/Registration).
• You can use custom paper sizes. For more information, see e-Manual > Settings/Registration > Registering/Editing/Deleting
Custom Paper Sizes.
• You can name, register, and edit custom paper types. For more information, see e-Manual > Settings/Registration >
Registering/Editing Custom Paper Types.
• The following paper sizes can be loaded into the Paper Drawer (Right/Left), and Paper Drawer 3 and 4:
• Paper Drawer (Right/Left): LTR
• Paper drawer 3 and 4: 11” x 17”, LGL, LTR, LTRR, STMTR, EXEC, and custom size (5 1/2” x 7 1/8” to 11 3/4” x 19 1/4” (139.7 mm x 182 mm to 297 mm x 487.7 mm))
• The paper size of the paper deck is fixed to LTR. For instructions on changing the paper size that can be loaded in the Paper
Deck Unit-A1, contact your local authorized Canon dealer.
• For more information on the paper types that can be loaded in paper drawers, see e-Manual > Basic Operations.
• If a message prompting you to load paper appears during printing, the remaining prints are automatically made after you load
the correct paper. If you select a different paper source, the remaining prints are made after you press [OK].
• Press [Cancel] to cancel printing.
62
1
Open the paper drawer.
1. Press the open button on
the paper drawer in which
you want to load paper.
2. Grip the handle, and pull
out the paper drawer until it
stops.
Routine Maintenance
Paper Drawer (Right/Left)
Paper Drawer 3 and 4
2
Prepare the paper to load.
Open the packaging for the
paper, and remove the paper
stack.
• For high-quality printouts, use paper recommended by Canon.
• Before loading paper, always fan the sheets several times, and align the edges to facilitate feeding.
63
3
Load the paper stack into the paper drawer.
Paper Drawer (Right/Left)
1. Make sure that the paper
size plate of the paper
drawer matches the size
of the paper loaded in the
paper drawer.
2. Load the paper stack against
the right wall of the paper
drawer.
3. Gently push the paper
drawer back into the
machine until it clicks into
place in the closed position.
Paper Drawer 3 and 4
When returning the paper drawer to its original position, be careful not to get your fingers
caught, as this may result in personal injury.
• Paper which is curled must be straightened out before loading it into the paper deck unit.
• You will not be able to make copies or print if you load paper that exceeds the loading limit mark (
is not completely pushed into the machine.
• Make sure that the height of the paper stack does not exceed the loading limit mark (
).
• Always check that the paper drawers are in place.
64
), or if the paper drawer
• If you print on the paper which has absorbed moisture, steam may come out from the output area of the machine. This is
because the moist on the paper evaporates when the high temperature is applied when a toner is fixed to the paper. It is not a
malfunction. (This especially happens in low room temperature.)
65
Routine Maintenance
• When loading paper into the paper drawer for the first time, set the paper size dial to match the paper size being loaded. (See
“Adjusting a Paper Drawer to Hold a Different Paper Size,” on p. 66.)
• Paper Drawer (Right/Left) hold approximately 1,500 sheets of paper (20 lb bond (80 g/m2)) or 1,700 sheets of paper (17 lb bond
(64 g/m2)).
• The number of sheets that can be loaded in the Paper Drawer 3 and 4 is 550 sheets of paper (20 lb bond (80 g/m2)) or 680
sheets of paper (17 lb bond (64 g/m2)).
• If there are instructions on the paper package about which side of the paper to load, follow those instructions.
• When the paper is loaded into the paper drawer, the side facing down is the one printed on.
• If problems, such as poor print quality or paper jams occur, try turning the paper stack over and reloading it.
• For more information on the print direction of preprinted paper (paper which has logos or patterns already printed on it), see
e-Manual > Copy.
• Rewrap any remaining paper in its original package, and store it in a dry place, away from direct sunlight.
• If paper runs out and printing is stopped, load a new paper stack. Printing restarts after the new paper stack is loaded.
Adjusting a Paper Drawer to Hold a Different Paper Size
If you want to load a different size paper into a paper drawer, follow the procedure described below to adjust the paper drawer
guides.
When handling paper, take care not to cut your hands on the edges of the paper.
1
Remove the paper loaded in the paper drawer.
2
Adjust the position of the paper drawer guides.
1. Press the open button on
the paper drawer for which
you want to adjust the paper
size.
2. Grip the handle, and pull
out the paper drawer until it
stops.
3. Remove all of the remaining
paper.
1. Slide the left guide while
squeezing it on the top to
align it with the mark for the
desired paper size.
2. Slide the front guide while
squeezing it on the top to
align it with the mark for the
desired paper size.
Slide the guides until they click into place. If the left guide and front guide are not aligned correctly, the
paper size will not correctly appear on the touch panel display. It is also necessary to adjust the guides
correctly to avoid causing a paper jam, dirty prints, or making the inside of the machine dirty.
66
3
Load the appropriate size paper into the paper drawer.
4
Change the paper drawer’s paper size plate to match the new paper size.
Routine Maintenance
1. Make sure that the paper
size setting of the paper
drawer matches the size
of the paper to load in the
paper drawer.
2. Load the paper stack against
the right wall of the paper
drawer.
1. Open the inside cover of the
paper drawer, and lift up the
plate.
2. Rotate the plate so that the
new paper size is on the
right side of the plate.
3. Insert the plate straight
down, and close the inside
cover.
The paper size that cannot be used depending on the model and settings is also listed on the paper size
plate.
5
Gently push the paper drawer back into the machine until it clicks into place in
the closed position.
When returning the paper drawer to its original position, be careful not to get your fingers
caught, as this may result in personal injury.
67
Loading Pre-Punched Paper
You can load pre-punched paper to the following paper source:
• Paper Drawers of the main unit
• Multi-purpose Tray
• Paper Deck Unit-A1
• Paper Deck Unit-D1
When loading pre-punched paper, take note of the orientation of the binding holes and the image.
When pre-punched paper is loaded in the paper drawer of the main unit, the side facing down is the one printed on.
When pre-punched paper is loaded in the Multi-purpose Tray, Paper Deck Unit-A1, or Paper Deck Unit-D1, the side facing up is
the one printed on.
• If you are making one-sided prints, select [Face Up (Reverse Order)] in [Face Up/Face Down]. (See e-Manual > Copy.)
• If you want to output prints with the printed face down, select plain paper with horizontal (landscape) orientation in [Select
Paper]. (See e-Manual > Copy.)
Loading Transparencies
You can load transparencies only in the multi-purpose tray.
Transparencies have a front and back side. To achieve sharp printing results, the side facing up is the one printed on.
• You can load only LTR or LTRR size transparencies.
• You cannot load the transparencies into the Paper Decks 3 and 4, Paper Deck (Right/Left), Paper Deck Unit-A1, Paper Deck
Unit-D1, Document Insertion/Folding Unit-H1, or Document Insertion Unit-L1.
• When loading transparencies, make sure to hold only the edges of the sheets and avoid touching the print surface.
• Do not load transparencies while the machine is printing. Doing so may cause a paper jam.
• Use only transparencies intended for use with this machine. If you use other transparencies, you may cause damage to the
machine.
• It is recommended that output transparencies are immediately removed from the output tray to avoid folding of the
transparencies and paper jams.
• Return the remaining transparencies to their original package for storage, avoiding locations subject to high temperatures and
humidity. Leaving transparencies loaded for an extended period of time may cause the sheets to stick together and result in a
paper jam.
• Leaving transparencies loaded for an extended period of time may cause the sheets to stick together and result in difficulties
feeding the transparencies. In this case, fan the loaded transparency sheets, or if you have loaded 100 or more sheets, reduce
the number of sheets to less than 100 or use new transparencies.
• When printing on transparencies, depending on the type of image, the image may become dense. When this happens, adjust
the density for the output image.
If a paper jam occurs, fan the loaded transparency sheets well.
68
Loading Tab Paper Using the Tab Feeding Attachment Kit-B1
(Optional)
This section describes how to load tab paper.
You can load tab paper to the following paper source:
• Paper Drawer 3 and 4 of the main unit
• Document Insertion/Folding Unit-H1/Document Insertion Unit-L1
Routine Maintenance
Only LTR tab paper can be used.
When you load tab paper into the paper drawer, make sure to register the paper type. (See e-Manual > Settings/Registration.)
How to Load Tab Paper
There are two kinds of tab paper: right order tab paper and reverse order tab paper.
1
1
2
2
3
3
4
4
Right Order Tab Paper
Reverse Order Tab Paper
If you load tab paper into the Paper Drawer 3 and 4 or Document Insertion/Folding Unit-H1/Document Insertion Unit-L1, load
reverse order tab paper face down with the tabs to the left side.
1
2
3
4
You cannot make copies or prints on tab paper that is loaded in the Document Insertion/Folding Unit-H1/Document Insertion
Unit-L1.
• You can use tab paper set in the Document Insertion/Folding Unit-H1/Document Insertion Unit-L1 for Add Cover, Insert Sheets
or Job Separator.
• If you want to insert printed tab paper as a chapter pages, insert a blank paper where the tab paper will be inserted.
• For more information on selecting the paper size or type of theDocument Insertion/Folding Unit-H1/Document Insertion
Unit-L1, see “Loading Paper into the Document Insertion/Folding Unit-H1/Document Insertion Unit-L1 (Optional),” on p. 81.
69
Loading Tab Paper
1
Open the paper drawer.
2
Adjust the position of the paper drawer guides.
1. Press the button on the
paper drawer in which you
want to load tab paper.
2. Grip the handle, and pull
out the paper drawer until it
stops.
1. Squeeze the upper part
of the left guide. Without
releasing it, slide the left
guide to the left as far as it
will go.
2. Squeeze the upper part of
the front guide. Without
releasing it, slide the front
guide to align it with the
mark for tab paper (LTR).
Slide the front guide until it clicks into place. If the front guide is not adjusted properly for the paper size
loaded in the paper drawer, the correct paper size may not appear on the touch panel display.
Adjust the front guide correctly to avoid causing a paper jam, dirty prints, or make the inside of the machine
dirty.
3
70
Remove the Tab Feeding Attachment Kit-B1.
1 Slide the Tab Feeding
Attachment Kit-B1 to the
left.
2 Remove the Tab Feeding
Attachment Kit-B1.
4
Place the Tab Feeding Attachment Kit-B1 aligning the mark for tab paper.
5
Place the Tab Feeding Attachment Kit-B1 aligning the mark for tab paper.
1 Place the Tab Feeding
Attachment Kit-B1 aligning
the mark for tab paper.
2 Slide the Tab Feeding
Attachment Kit-B1 to the
back of the paper drawer.
Routine Maintenance
1 Load the tab paper face
down with the tabs facing
left.
Even out the edges of the paper
stack.
Load the paper stack against the
right wall of the paper drawer.
2 Gently push the paper
drawer back into the
machine until it clicks into
place in the closed position.
When returning the paper drawer to its original position, be careful not to get your fingers
caught, as this may result in personal injury.
• Paper which has been rolled or curled must be straightened out prior to use.
• You will not be able to make copies or print if you load paper that exceeds the loading limit mark (.
) or
if the paper drawer is not completely pushed into the machine.
• Make sure that the height of the paper stack does not exceed the limit mark (
) at the back of the paper
drawer.
• Always check that the paper drawers are in place.
• Never place paper or any other items in the empty part of the drawer next to the paper stack. Doing so may
cause paper jams.
• When you are not loading tab paper, make sure to return the Tab Feeding Attachment Kit-B1 to its holder.
Using the Tab Feeding Attachment Kit-B1 for storing paper other than tab paper may cause a paper jam.
71
Loading Paper into the Paper Deck Unit-A1/Paper Deck Unit-D1
(Optional)
If you attach the Paper Deck Unit-A1 or Paper Deck Unit-D1 to the machine, you have one additional source of paper for
printing jobs.
The Paper Deck Unit-A1 or Paper Deck Unit-D1 hold up to 3,500 sheets of paper (20 lb bond (80 g/m2)).
If the machine is in the Sleep mode (the touch panel is not displayed, and only
(Energy Saver) is lit), you may be unable to
open the paper deck unit. In this case, press
(Energy Saver) to reactivate the machine, and then press the open button on the
paper deck unit.
• The Paper Deck Unit-A1 and Paper Deck Unit-D1 are optional products.
• The following paper sizes can be loaded into the Paper Deck Unit-A1 or Paper Deck Unit-D1:
• Paper Deck Unit-A1: LTR
• Paper Deck Unit-D1: 11” x 17”, LGL, LTR, and LTRR
• The paper size of the Paper Deck Unit-A1 is fixed to LTR. For instructions on changing the paper size that can be loaded in the
Paper Deck Unit-A1, contact your local authorized Canon dealer.
Loading Paper into the Paper Deck Unit-A1/Paper Deck Unit-D1
If you select the paper deck when it has no paper, or if the paper deck runs out of paper during a print job, a screen prompting
you to load paper appears on the touch panel display.
Follow the procedure below to load paper into the paper deck.
When handling paper, take care not to cut your hands on the edges of the paper.
• The Paper Deck Unit-A1 and Paper Deck Unit-D1 can only accommodate paper from 14 lb bond to 80 lb cover (52 to 220 g/m2)
in weight.
• If paper runs out and printing is stopped when you are printing in the Staple mode, do not remove the output sheets that are
waiting to be stapled. (Printing and stapling resume after you clear the paper jam.)
If a message prompting you to load paper appears during printing, the remaining prints are automatically made after you load
the correct paper. If you select a different paper source, the remaining prints are made after you press [OK].
72
1
Open the paper deck unit.
2
Prepare the paper to load.
1. Press the open button.
2. Open the paper deck unit.
The inside lifterautomatically
descends to the paper loading
position.
Routine Maintenance
Open the packaging for the
paper, and remove the paper
stack.
• For high-quality printouts, use paper recommended by Canon.
• Before loading paper, always fan the sheets several times, and align the edges to facilitate feeding.
3
Load the paper stack into the paper deck unit.
1 Load the paper stack against
the inner paper guide of the
paper deck unit.
2 Close the paper deck unit.
The inside lifter automatically
ascends, and the machine
becomes ready for printing.
When closing the paper deck unit, be careful not to get your fingers caught, as this may result in
personal injury.
73
• Do not load the following types of paper into the Paper Deck Unit-A1/Paper Deck Unit-D1. Doing so may cause a paper jam.
•
•
•
•
•
•
•
•
•
•
Severely curled or wrinkled paper
Thin straw paper
Heavy paper (more than 80 lb cover (220 g/m2))
Paper which has been printed on using a thermal transfer printer
The reverse side of paper which has been printed on using a thermal transfer printer
Coated paper
Tracing paper
Transparencies
Tab paper
Labels
• Paper which is curled must be straightened out before loading it into the paper deck unit.
• Do not load paper into the Paper Deck Unit-A1/Paper Deck Unit-D1 that has been previously copied onto, as this may result in
a malfunction or damage to the machine. Always use the multi-purpose tray to feed paper when you want to copy onto the
back of a sheet of paper that already has something copied on its front side (2nd side of 2-Sided copy).
• Never place paper or any other items in the empty part of the paper deck unit next to the paper stack. Doing so may cause
paper jams.
• You will not be able to make copies or print if you load paper that exceeds the loading limit mark (
), or if the paper
drawer is not completely pushed into the paper deck unit.
• Make sure that the height of the paper stack does not exceed the loading limit mark (
).
• Always check that the paper deck unit is in place.
• Load the paper stack in stages, adding approximately 550 sheets of paper at a time. If the Paper Deck Unit-A1/Paper Deck
Unit-D1 can accommodate more paper, the lifter will descend.
• If there are instructions on the paper package about which side of the paper to load, follow those instructions.
• When paper is loaded in the Paper Deck Unit-A1/Paper Deck Unit-D1, the side facing up is the one printed on.
• If problems, such as poor print quality or paper jams occur, try turning the paper stack over and reloading it.
• Rewrap any remaining paper in its original package, and store it in a dry place, away from direct sunlight.
• If paper runs out and printing is stopped, load a new paper stack. Printing restarts after the new paper stack is loaded.
74
Changing the Paper Size for the Paper Deck Unit-D1
This section explains how to change the paper size for the Paper Deck Unit-D1.
1
Register the desired paper size for the Paper Deck Unit-D1 in [Paper Settings] in
[Preferences] (Settings/Registration).
2
Remove all of the loaded paper and the paper size sheet in the paper deck.
Routine Maintenance
For instructions on registering the paper size for the Paper Deck Unit-D1, see e-Manual > Settings/
Registration.
1. Press the open button.
2. Open the paper deck.
The inside lifter automatically
descends to the paper loading
position.
3. Remove all of the loaded
paper and the paper size
sheet.
It may take some time for the paper deck to open, even if you press the open button.
3
Remove the white screw on the top of the back size switch plate A by turning it
counterclockwise.
*
* Back Size Switch Plate A
75
4
Remove the back size switch plate A.
5
Remove the white screw on the back size switch plate B.
*
* Back Size Switch Plate B
6
76
Remove the back size switch plate B.
7
Align the back size switch plate B with the marks for the desired paper size.
Routine Maintenance
• If the back size switch plate B is not adjusted properly for the paper size loaded in the paper deck, the
correct paper size may not appear on the touch panel display.
• Adjust the back size switch plate B correctly to avoid causing a paper jam, dirty prints, or make the inside of
the machine dirty.
8
Fix the back size switch plate B to the paper deck with the white screw by turning
it clockwise.
77
9
Insert and align the back size switch plate A with the marks for the desired paper
size.
• f the back size switch plate A is not adjusted properly for the paper size loaded in the paper deck, the
correct paper size may not appear on the touch panel display.
• Adjust the back size switch plate A correctly to avoid causing a paper jam, dirty prints, or make the inside of
the machine dirty.
10
Fix the back size switch plate A with the white screw by turning it clockwise.
11
Remove the white screw on the front size switch plate by turning it
counterclockwise.
*
* Front Size Switch Plate
78
13
Align the front size switch plate with the marks for the desired paper size.
Routine Maintenance
12
Remove the front size switch plate.
• If the front size switch plate is not adjusted properly for the paper size loaded in the paper deck, the correct
paper size may not appear on the touch panel display.
• Adjust the front size switch plate correctly to avoid causing a paper jam, dirty prints, or make the inside of
the machine dirty.
14
Fix the front size switch plate to the paper deck with the white screw by turning it
clockwise.
79
15
Insert the correct underlay sheet that matches the new paper size into the paper
deck.
16
Load the paper stack into the paper deck.
17
Place a size sticker indicating the new paper size that is loaded in the Paper Deck
Unit-D1.
18
Close the paper deck.
80
Align the arrow on the underlay sheet with the guide on the paper deck’s left wall.
The inside lifter automatically rises, and prepares the paper deck for feeding.
When closing the paper deck, be careful not to get your fingers caught, as this may result in
personal injury.
Loading Paper into the Document Insertion/Folding Unit-H1/
Document Insertion Unit-L1 (Optional)
Follow the procedure below to load the paper into the Document Insertion/Folding Unit-H1 or Document Insertion Unit-L1.
• The Document Insertion/Folding Unit-H1 and Document Insertion Unit-L1 are optional products.
• The following paper sizes can be loaded into the Document Insertion/Folding Unit-H1 or Document Insertion Unit-L1:
• 11” x 17”, LGL, LTR, LTRR, and EXEC
1
Adjust the slide guides to fit the paper size.
2
Prepare the paper to load.
Open the packaging for the
paper, and remove the paper
stack.
• For high-quality printouts, use paper recommended by Canon.
• Before loading paper, always fan the sheets several times, and align the edges to facilitate feeding. Also,
you should always fan paper that has just been removed from a newly opened paper package.
81
Routine Maintenance
• For more information on available paper stock that can be loaded into the Document Insertion/Folding Unit-H1 or Document
Insertion Unit-L1, see e-Manual > Basic Operations.
3
4
Load the paper stack into the document insertion unit.
Load the paper face up.
Select the desired paper size  press [Next].
Select the same paper size that is loaded in the Document Insertion/Folding Unit-H1 or Document Insertion
Unit-L1.
To select an A or B series paper size, press [Inch Size].
5
Select the desired paper type  press [OK].
When printing on special types of paper, such as heavy paper, be sure to correctly set the paper type. If the
type of paper is not set correctly, it could adversely affect the quality of the image. Moreover, the fixing unit
may become dirty and require a service repair, or the paper could jam.
• Only load paper for use as a cover.
• You cannot make copies or prints on paper that is loaded in the Document Insertion/Folding Unit-H1 or
Document Insertion Unit-L1.
• You can load the coated paper (29 lb bond to 140 lb index (106 to 256 g/m2)) into the Document
Insertion/Folding Unit-H1 or Document Insertion Unit-L1. You cannot load the coated paper into the
Paper Drawer (Right/Left), Paper Drawer 3 and 4, multi-purpose tray, Paper Deck Unit-A1, or Paper Deck
Unit-D1.
• A maximum of 100 sheets of paper (20 lb bond (80 g/m2)) can be loaded in the tray of Document
Insertion/Folding Unit-H1 or Document Insertion Unit-L1.
82
Replacing the Stamp Cartridge
(Duplex Color Image Reader
Unit-G1)
Originals sent via the Duplex Color Image Reader Unit-G1 can be stamped to indicate that they have been sent. Replace the
stamp cartridge when the stamp mark is faint or no longer visible.
The Duplex Color Image Reader Unit-G1 is an optional product.
1
Open the feeder, and open the document scan cover.
1. Open the feeder.
2. Pull the lever above the
feeder, and open the
document scan cover.
Open the document scan cover carefully, as not to scratch the platen glass.
2
Open the stamp cover.
83
Routine Maintenance
When replacing the stamp cartridge, take care not to allow ink to come into contact with your hands or clothing. If ink gets onto
your hands or clothing, wash it off immediately with cold water.
3
Insert the stamp cartridge.
1. Remove the old stamp
cartridge, using tweezers.
2. Push in the new stamp
cartridge until it clicks.
• Insert the stamp cartridge so that it is not slanted.
• Insert the stamp cartridge properly, or paper jams may occur.
4
Close the stamp cover.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
84
5
Close the document scan cover, and the feeder.
1. Close the document scan
cover.
2. Close the feeder.
Routine Maintenance
• When closing the document scan cover and the feeder, be careful not to get your fingers caught,
as this may result in personal injury.
• Be aware that the light emitted from the platen glass may be very bright when closing the
feeder.
85
Replacing the Staple Cartridge
(For Optional Products)
This section describes how to replace the staple case and staple cartridge in the stapler unit and saddle stitcher unit.
Replacing the Staple Cartridge in the Stapler Unit (Staple
Finisher-P1/Booklet Finisher-P1)
When the stapler unit of the Staple Finisher-P1 or Booklet Finisher-P1 is almost out of staples and the staple cartridge in the stapler
unit must be replaced, a screen prompting you to replace the staple cartridge appears on the touch panel display. Follow the
procedure described below to replace the staple cartridge.
Remove the orange seal that holds the staples together after you place the staple cartridge into the staple case.
• The Staple Finisher-P1 and Booklet Finisher-P1 are optional products.
• We recommend that you order staple cartridges from your local authorized Canon dealer before your stock runs out.
• Use only staple cartridges intended for use with this machine.
86
1
Open the front cover of the finisher.
Routine Maintenance
*1
*2
*1 Booklet Finisher-P1
*2 Staple Finisher-P1
2
Pull out the staple case, holding it by the green tab.
3
Pull out the empty staple cartridge from the staple case.
1. Press the areas indicated by
PUSH on both sides of the
staple case.
2. Once you have released the
spring-loaded case, pull out
the staple cartridge.
1
PUS
H
1
2
87
4
Insert a new staple cartridge into the staple case.
1. Insert a new staple cartridge.
2. Press the spring-loaded
case down until it clicks into
place.
3. Remove the seal holding the
staples together, by pulling
it straight out.
2
1
3
• Do not remove the seal that holds the staples together before you place the staple cartridge into the
staple case.
• Only one staple cartridge can be inserted at a time.
• Make sure that you pull the seal straight out. If you pull it out at an angle, it may tear.
5
Gently push the staple case back into the finisher and push down firmly until it
is securely in place.
6
Close the front cover of the finisher.
When closing the front cover of the finisher, be careful not to get your fingers caught, as this may
result in personal injury.
After the cover is closed, the stapler unit may automatically perform a “dry” stapling operation to reposition
the staples.
88
Replacing the Staple Case in the Saddle Stitcher Unit (Booklet
Finisher-P1)
When the saddle stitcher unit of the Booklet Finisher-P1 is almost out of staples and the staple cartridge in the saddle stitcher
unit must be replaced, a screen prompting you to replace the staple cartridge appears on the touch panel display. Follow the
procedure described below to replace the staple cartridge.
Routine Maintenance
If necessary, remove all output paper in the booklet tray before replacing the staple cartridge of the saddle stitcher unit.
• This procedure is necessary only if the Booklet Finisher-P1 is attached (the Booklet Finisher-P1 is an optional product).
• We recommend that you order staple cases from your local authorized Canon dealer before your stock runs out.
• Use only staple cases intended for use with this machine.
• Remove the black part on the end before inserting the staple case.
89
1
Open the front cover of the finisher.
2
Pull out the saddle stitcher unit, and then push the stapler unit up.
*2
*1
1. Grip the handle of the
saddle stitcher unit, and
pull out until it stops.
2. Pull the stapler unit of
the saddle stitcher unit
towards you, and then
push it up.
*1 Stapler Unit
*2 Saddle Stitcher Unit
3
Insert the new staple case.
1. Pull out the empty staple
case, holding it by its left
and right sides.
2. Push the new staple case
in until it clicks into place.
\
• Only one staple case can be inserted at a time.
• When replacing the staple cases, replace both the front and back staple cases.
90
4
Push the saddle stitcher unit back into its original position.
Routine Maintenance
1. Pull the stapler unit of
the saddle stitcher unit
towards you, and then
push it down into its
original position.
2. Grip the handle of the
saddle stitcher unit, and
return it to its original
position.
When pushing the saddle stitcher unit back into its original position, be careful not to get your
fingers caught, as this may result in personal injury.
5
Close the front cover of the finisher.
When closing the front cover of the finisher, be careful not to get your fingers caught, as this may
result in personal injury.
When you have replaced the staple case, be sure to manually reposition the staples in the saddle stitcher
unit. (See e-Manual > Settings/Registration.)
91
Removing Punch Waste (External
2/3 Hole Puncher-A1)
This section describes how to remove punch waste from the puncher.
When the punch waste tray of the Puncher becomes full, a screen prompting you to remove the punch waste appears on the
touch panel display. Follow the procedure described below to remove the punch waste.
• The External 2/3 Hole Puncher-A1 is an optional product.
• The External 2/3 Hole Puncher-A1 is available only when the Staple Finisher-P1 or Booklet Finisher-P1 is attached.
1
Pull out the punch waste tray.
2
Discard the punch waste.
1. Open the front cover of the
puncher.
2. Pull out the punch waste
tray.
Make sure that the punch waste tray is completely emptied.
92
3
Return the punch waste tray to its original position.
1. Push the punch waste
tray back into its original
position.
2. Close the front cover of the
puncher.
Routine Maintenance
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
If the punch waste tray is not securely in place, you cannot make copies or prints in the Hole Punch mode.
93
Replacing the Toner Cartridge
When the message <Replace toner cartridge.> is displayed on the touch panel display, press
replace the toner cartridge.
on the bottom right and
When the toners run out completely and prints can no longer be made, a screen with instructions on how to replace the toner
cartridge appears on the touch panel display. Follow the procedure described below to replace the toner cartridge.
If you press [Close], you can continue operations, such as setting modes and scanning originals, even if you do not replace the
toner cartridge immediately.
• Do not burn or throw used toner cartridges into open flames, as this may cause the toner to ignite,
resulting in burns or a fire.
• If you accidentally spill or scatter toner, carefully gather the toner particles together or wipe them up
with a soft, damp cloth in a way that prevents inhalation. Never use a vacuum cleaner that does not have
safeguards against dust explosions to clean up spilled toner. Doing so may cause a malfunction in the
vacuum cleaner, or result in a dust explosion due to static discharge.
• Keep toner out of the reach of small children.
• If toner is ingested, consult a physician immediately.
• If toner gets onto your hands or clothing, wash it off immediately with cold water. Washing it off with
warm water will set the toner, and make it impossible to remove the toner stains.
94
•
•
•
•
Use only toner cartridges intended for use with this machine.
For information on the supported Canon genuine toner, see “Consumables,” on p. 108.
Do not replace toner cartridges until the message prompting you to do so appears.
You can replace a toner cartridge while the machine is printing.
1
Press [
2
Open the toner replacement cover, by holding the left and right handles.
Routine Maintenance
• Complete instructions on how to replace the toner cartridge can be accessed by pressing [Previous] or [Next] on the touch
panel display.
• If toner runs out during a print job, the remaining prints are made after you replace the toner cartridge.
• After replacing toner cartridges, if printed gradation and density are different from the gradation and density printed before
you replaced the toner cartridges, perform an [Auto Adjust Gradation] in [Adjustment/Maintenance] (Settings/Registration).
(See e-Manual > Settings/Registration.)
].
If a screen with instructions on how to replace the toner cartridge appears on the touch panel display, this
step is not necessary.
If equipment such as finisher is attached, open the cover by holding the right handle.
95
3
Turn the locking lever to the right until it stops.
Make sure to turn the locking lever to the right until it stops. (Otherwise, you may not be able to remove the
toner cartridge.)
4
Remove the toner cartridge, supporting it with both hands.
Do not burn or throw used toner cartridges into open flames, as this may cause the toner
remaining inside the cartridges to ignite resulting in burns or a fire.
Never touch the tip of the toner cartridge or subject it to shock by hitting it. Doing so may cause the toner
cartridge to leak.
96
6
Twist the red protective cap of the new toner cartridge in the direction of the
arrow to remove it.
7
Insert the new toner cartridge.
Routine Maintenance
5
Prepare the new toner cartridge.
Align the end of the toner cartridge with the toner supply port as shown by the arrow in the
illustration below, and insert the toner cartridge straight into the machine.
• Only use toner cartridges intended for use in this machine. You cannot insert the toner cartridge not
intended for use in this machine, because the shape of the toner cartridge does not match the toner
supply port of the machine.
• Insert the toner cartridge horizontally into the machine. Otherwise, the toner cartridge may leak.
97
8
Turn the locking lever to the left until it stops, and close the toner replacement
cover.
1 Turn the locking lever to the
left until it stops.
2 Close the toner replacement
cover.
The toner confirmation screen is displayed.
When closing the toner replacement cover, be careful not to get your fingers caught, as this may
result in personal injury.
Make sure to turn the locking lever to the left until it stops. (Otherwise, you may not be able to close the
toner replacement cover.)
98
Routine Cleaning
If the original is not copied clearly or streaks appear on printed output, clean the following parts of the machine. For highquality printouts, we recommend cleaning these parts once or twice a month.
● Platen glass
● Underside of the feeder
● Drums
If the touch panel display becomes dirty and the screen may not be seen clearly, clean the touch panel display. Since the touch
panel display becomes dirty from normal use, we recommend that you clean it once a week or every 10 days.
• When cleaning the machine, first turn OFF the main power switch, and disconnect the power cord.
Failure to observe these steps may result in a fire or electrical shock.
• Disconnect the power cord from the power outlet regularly, and clean the area around the base of
the power plug’s metal pins and the power outlet with a dry cloth to ensure that all dust and grime is
removed. If the power cord is connected for a long period of time in a damp, dusty, or smoky location,
dust can build up around the power plug and become damp. This may cause a short circuit and result in
a fire.
• When cleaning with a cloth, do not dampen it too much, as this may damage the original or break the machine.
• Do not use alcohol, benzene, paint thinner, or other solvents for cleaning. Doing so may result in damage to the plastic parts.
The Duplex Color Image Reader Unit-G1 is an optional product.
Platen Glass and Underside of the Feeder
If the platen glass or the underside of the feeder is dirty, the original may not be scanned clearly, or the size of the original may
be detected incorrectly. Clean the platen glass and the underside of the feeder by following the procedure below.
This procedure is necessary only if the Duplex Color Image Reader Unit-G1 is attached.
1
Clean the platen glass and the underside of the feeder with a cloth which is
wrung after being dampened in water or a mild detergent, and then wipe them
clean with a soft, dry cloth.
1. Clean the platen glass.
2. Clean the underside of the
feeder.
99
Routine Maintenance
● Wires
Manual Feeder Cleaning
If originals that have been fed through the feeder have streaks or appear dirty, clean the feeder’s scanning area and the rollers.
Clean the rollers of the feeder with a cloth which is wrung after being dampened in water, and then wipe them clean with a
soft, dry cloth.
• Spin the rollers while cleaning them.
• If the document feed scanning area is dirty, documents may not be scanned clearly, and the size of the document may not be
detected correctly.
This procedure is necessary only if the Duplex Color Image Reader Unit-G1 is attached.
Cleaning the Original Scanning Area of the Feeder
1
Clean the original Scanning area (thin glass strip).
2
Open the covers.
1 Open the feeder.
2 Clean the original scanning
area (thin glass strip) with
a cloth dampened in water,
and then wipe the area with
a soft dry cloth.
1 Pull the lever above the
feeder, and open the
document scan cover.
2 Hold the blue tab above the
inside cover, and open the
inside cover in the direction
of the arrow.
Open the document scan cover carefully, as not to scratch the platen glass.
100
4
Close the covers and the feeder.
Routine Maintenance
3
Clean the feed scanning area with a cloth dampened in water or a mild
detergent, and then wipe the area with a soft dry cloth.
1 Close the inside cover.
2 Close the document scan
cover.
3 Close the feeder.
• When closing the covers and the feeder, be careful not to get your fingers caught, as this may
result in personal injury.
• Be aware that the light emitted from the platen glass may be very bright when closing the
feeder.
101
Cleaning the Feeder’s Rollers
Spin the rollers while cleaning them.
1
Pull the lever, and open the feeder cover.
2
Clean the rollers (a total of five places) inside the feeder cover with a cloth
dampened with water. Then, wipe the area with a soft, dry cloth.
3
Clean the rollers inside the inner cover.
102
1 Open the inner cover,
holding it by its front tab.
2 Clean the rollers (a total
of five places) inside the
inner cover with a cloth
dampened with water. Then,
wipe the area with a soft dry
cloth.
4
Close the covers.
5
Clean the resin roller.
1 Close the inner cover.
2 Close the feeder cover.
• When closing the feeder, be careful not to get your fingers caught, as this may result in personal
injury.
• Be aware that the light emitted from the platen glass may be very bright when closing the
feeder.
103
Routine Maintenance
1 Open the feeder.
2 Clean the left side of the
rubber roller with a cloth
dampened with water. Then,
wipe the area with a soft dry
cloth.
3 Close the feeder.
Automatic Feeder Cleaning
If your originals have black streaks or appear dirty after scanning them through the feeder, perform an automatic feeder
cleaning for the rollers of the feeder.
This procedure is necessary only if the Duplex Color Image Reader Unit-G1 is attached.
1
2
3
Press
(Settings/Registration).
Press [Adjustment/Maintenance]  [Maintenance]  [Clean Feeder].
Place 10 sheets of blank paper into the feeder  press [Start].
It takes approximately 20 seconds to clean the feeder.
Use normal LTR size paper.
When cleaning is complete, try scanning again.
• Feeder Cleaning cannot be performed during printing.
• To cancel feeder cleaning while it is in progress, press [Cancel].
104
Wire Cleaning
If streaks appear on printed output or random parts of the printed image are missing, clean the corona assembly wires inside
the main unit.
2
3
(Settings/Registration).
Routine Maintenance
1
Press
Press [Adjustment/Maintenance]  [Maintenance]  [Clean Wire].
Press [Start].
It takes approximately 35 seconds to clean the wire.
When cleaning is complete, try printing again.
Wire cleaning cannot be performed during printing.
105
Drum Cleaning
Printed images may be light or distorted when the machine is used immediately after installation or after a long period time of
not using the machine. If printed images are light or distorted, clean the drum inside the machine as necessary.
1
2
3
106
Press
(Settings/Registration).
Press [Adjustment/Maintenance]  [Maintenance]  [Clean Drum].
Press [Start].
It takes approximately 5 minutes to clean the drum.
When cleaning is complete, try printing again.
Drum cleaning cannot be performed during printing.
Cleaning the Touch Panel Display
If the touch panel display becomes dirty and the screen may not be seen clearly, clean the touch panel display.
Routine Maintenance
1
Wipe the touch panel display with a cloth dampened in water or a mild cleaning
agent, and then wipe the area clean with a soft, dry cloth.
Control Panel (Flat)
Upright Control Panel-B1
107
Consumables
The following consumables are available from Canon. For more information, contact your local authorized Canon dealer. We
recommend that you order paper stock and toner from your local authorized Canon dealer before your stock runs out.
● Recommended Paper
In addition to plain paper (11” x 17”, LGL, LTR, and STMT size), recycled paper, color paper, transparencies (recommended
for this machine), tracing paper, labels, and other types of paper stock are available.
Do not store paper in places exposed to open flames, as this may cause the paper to ignite, resulting in
burns or a fire.
• Some commercially available paper types are not suited for this machine. Contact your local authorized Canon dealer when
you need to purchase paper.
• To prevent moisture build-up, tightly wrap any remaining paper in its original package for storage.
For high-quality printouts, use paper recommended by Canon.
● Toner
If a message prompting you to replace the toner cartridge appears on the touch panel display, replace the used toner
cartridge with a new one.
Only use toner cartridges intended for use with this machine.
For optimum print quality, using Canon genuine toner is recommended.
Product Name
imageRUNNER ADVANCE
6275/6265/6255
108
Supported Canon Genuine Toner
Canon GPR-38 Black Toner
• Do not burn or throw used toner cartridges into open flames, as this may cause the toner remaining
inside the cartridges to ignite, resulting in burns or a fire.
• Do not store toner cartridges in places exposed to open flames, as this may cause the toner to ignite,
resulting in burns or a fire.
• If you accidentally spill or scatter toner, carefully gather the toner particles together or wipe them up
with a soft, damp cloth in a way that prevents inhalation. Never use a vacuum cleaner that does not have
safeguards against dust explosions to clean up spilled toner. Doing so may cause a malfunction in the
vacuum cleaner, or result in a dust explosion due to static discharge.
• Store toner cartridges in a cool location, away from direct sunlight. (The recommended storage conditions are temperatures
below 86°F, and humidity below 80%.)
• [Be careful of counterfeit toners]
Please be aware that there are counterfeit Canon toners in the marketplace. Use of counterfeit toner may result in poor print
quality or machine performance. Canon is not responsible for any malfunction, accident or damage caused by the use of
counterfeit toner.
For more information, see http://www.canon.com/counterfeit.
● Stamp Cartridge
The stamp cartridge is used to stamp originals. Use the tweezers provided to remove and replace the stamp cartridge.
Stamp Ink Cartridge-C1
109
Routine Maintenance
Keep toner out of the reach of small children. If toner is ingested, consult a physician immediately.
● Staple Cartridge in the Stapler Unit
Finisher
Staple Finisher-P1
Booklet Finisher-P1
Name
Shape
Staple-J1
● Staple Cartridge in the Saddle Stitcher Unit
Finisher
Name
Shape
Staple Cartridge-D2
Booklet Finisher-P1
Staple Cartridge-D3
● Genuine Supplies
Canon has developed and manufactured Toner, Parts, and Supplies specifically for use in this machine. For optimal print
quality and for optimal machine performance and productivity, we recommend that you use Genuine Canon Toner, Parts,
and Supplies.
Contact your Canon Authorized Dealer or Service Provider for Genuine Canon Supplies.
110
Troubleshooting
Troubleshooting
4
Clearing Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Locations of Paper Jams • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 113
Main Unit• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 117
Paper Sources • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 123
Duplex Color Image Reader Unit-G1 (Optional) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 131
Document Insertion/Folding Unit-H1/Document Insertion Unit-L1 (Optional)• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 134
External 2/3 Hole Puncher-A1 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 144
Staple Finisher-P1/Booklet Finisher-P1 (Optional) • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 148
Copy Tray-Q1 (Optional)• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 158
Reducing the Frequency of Paper Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Clearing Staple Jams (For Optional Products). . . . . . . . . . . . . . . . . . . . . . 163
Locations of Staple Jams • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 163
Stapler Unit of the Staple Finisher-P1/Booklet Finisher-P1 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 164
Saddle Stitcher Unit of the Booklet Finisher-P1 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 166
If Memory Becomes Full During Scanning . . . . . . . . . . . . . . . . . . . . . . . . . 169
For the Copy Function • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 169
For the Fax/Scan and Send Function• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 169
For the Scan and Store Function • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 170
When an Error Message Is Displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
When an Error Code Is Displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Printer/Fax Driver Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
Service Call Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Contacting Your Local Authorized Canon Dealer • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 175
Setting the Limited Functions Mode from the Service Call Message Screen • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 177
Functions Available When the Printer/Scanner Cannot Be Used Due to an Error • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 178
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
111
Clearing Paper Jams
If a paper jam occurs, a screen indicating the location of the paper jam and how to clear the jam appears on the touch panel
display. Follow the instructions on the screen to clear the paper jam. The screen is displayed repeatedly until the paper jam
is cleared. If you press [Close], you can continue operations, such as setting modes or scanning originals, even if the jammed
paper is not removed immediately.
Some areas inside the machine are subject to high-voltages. When removing jammed paper or when
inspecting the inside of the machine, do not allow necklaces, bracelets, or other metal objects to touch
the inside of the machine, as this may result in burns or electrical shock.
• When removing jammed originals or paper, take care not to cut your hands on the edges of the originals
or paper. If you cannot remove the paper, contact your local authorized Canon dealer.
• When removing paper which has become jammed inside the machine, take care not to allow the toner
on the jammed paper to come into contact with your hands or clothing, as this will dirty your hands or
clothing. If they become dirty, wash them immediately with cold water. Washing them with warm water
will set the toner, and make it impossible to remove the toner stains.
• When removing paper which has become jammed inside the machine, remove the jammed paper gently
to prevent the toner on the paper from scattering and getting into your eyes or mouth. If the toner gets
into your eyes or mouth, wash them immediately with cold water and immediately consult a physician.
• The fixing unit and its surroundings inside the machine may become hot during use. When removing
jammed paper or when inspecting the inside of the machine, do not touch the fixing unit and its
surroundings, as doing so may result in burns or electrical shock.
• After clearing all paper jams, remove your hands from the machine immediately. Even if the machine is
not in operation, your hands, hair, or clothing may get caught in the feed rollers, which could result in
personal injury or damage if the machine suddenly starts printing.
• If a paper jam occurs in the feeder, you cannot continue operating the machine. Follow the directions on the touch panel
display to clear the paper jam. (See “Duplex Color Image Reader Unit-G1 (Optional),” on p. 131.)
• Some areas that are shown to have paper jams may not actually have paper jams. However, always check all locations indicated
on the touch panel display in the order that is given.
• If a paper jam occurs and printing is stopped when you are printing in the Staple mode, do not remove the paper from the
areas except those which are shown to have paper jams on the touch panel display. For example, if paper is jammed in the
main unit, do not remove the output sheets on the finisher which does not have paper jams. (Printing and stapling resume
after you clear the paper jam in the main unit.)
If paper is jammed in several locations, remove the jammed paper in the order indicated on the touch panel display.
112
Locations of Paper Jams
Paper jams may occur in the following parts of the machine. See the applicable section to clear the paper jam.
Multi-purpose Tray (p. 123)
Fixing Transport Unit (p. 119)
Paper Drawers (Right/Left) (p. 125)
Paper Drawers 3 and 4 (p. 124)
113
Troubleshooting
Inside the Upper and Lower Right Covers (p. 117)
Duplex Color Image Reader Unit-G1
(Optional) (p. 131)
Copy Tray-Q1 (Optional) (p. 158)
114
Paper Deck Unit-A1/Paper Deck
Unit-D1 (Optional) (p. 127)
Insertion Unit (p. 134)
Troubleshooting
Inside the Insertion Unit (p. 137)
External 2/3 Hole Puncher-A1 (p. 144)
Folding Unit (p. 140)
115
Output Area (p. 150)
Inside the Top Cover (p. 148)
Saddle Stitcher Unit of the Booklet
Finisher-P1 (p. 155)
Front Cover of the Booklet
Finisher-P1 (p. 153)
116
Main Unit
If a paper jam occurs in the main unit area, a screen prompting you to remove the jammed paper appears on the touch panel
display. Check the location of the paper jam, and follow the procedure described below, while referring to the directions that
appear on the touch panel display, to remove the jammed paper.
The Copy Tray-Q1, Paper Deck Unit-A1, Paper Deck Unit-D1 are the optional products.
Inside the Upper and Lower Right Covers
1
Remove any jammed paper from the upper right cover of the main unit.
1 Open the upper right cover.
2 Remove any jammed paper.
3 Close the upper right cover.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
117
Troubleshooting
When the Paper Deck Unit-A1/Paper Deck Unit-D1 is attached, move the Paper Deck Unit-A1/Paper Deck Unit-D1 away from the
main unit beforehand.
2
Remove any jammed paper from the lower right cover of the main unit.
1. Open the lower right cover.
2. Remove any jammed paper.
3. Close the lower right cover.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
When thePaper Deck Unit-A1/Paper Deck Unit-D1 is attached, reconnect the Paper Deck Unit-A1/Paper
Deck Unit-D1 to the main unit.
3
118
Follow the instructions on the touch panel display.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
Fixing Transport Unit
If the Copy Tray-Q1 is attached to the main unit, follow the procedures described in “Copy Tray-Q1 (Optional),” on p. 158. to
remove the jammed paper.
2
Turn the dial in the direction of the arrow (counterclockwise) 10 times.
Troubleshooting
1
Open the front cover of the main unit.
This procedure makes it easier to remove the jammed paper in the following procedures, because the jammed
paper moves to the fixing transport unit.
119
3
Pull out the fixing transport unit.
4
Remove any jammed paper from the left guide.
5
Remove any jammed paper from the fixing unit.
1. Move the green lever in the direction
of the arrow.
2. Pull out the fixing transport unit.
1. Open the left guide.
2. Remove any jammed paper.
If you cannot pull out the jammed paper, proceed to the next step. Do not pull out jammed paper by force,
as this may leave torn pieces inside the machine and cause the machine to malfunction.
120
6
Remove any jammed paper from the lower guide.
1 Open the lower guide, holding by
the green tab.
2 Remove any jammed paper.
3 Close the lower guide.
Troubleshooting
When closing the guide, be careful not to get your fingers caught, as this may result in personal
injury.
7
Remove any jammed paper from the fixing unit.
1 Pull the paper gently.
2 Turn the knob to the left to remove
any jammed paper.
3 Close the left guide.
When closing the guide, be careful not to get your fingers caught, as this may result in personal
injury.
121
8
Push the fixing transport unit back into its original position, and close the front
cover.
1 Push the fixing transport unit back
into its original position.
2 Return the green lever to its original
position.
3 Close the front cover.
When returning the unit to its original position or closing the cover, be careful not to get your
fingers caught, as this may result in personal injury.
9
122
Follow the instructions on the touch panel display.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
Paper Sources
If a paper jam occurs in paper sources, a screen prompting you to remove the jammed paper appears on the touch panel
display. Check the location of the paper jam, and follow the procedure described below, and the procedure that appears on the
touch panel display, to remove the jammed paper.
The Paper Deck Unit-A1 and Paper Deck Unit-D1 are optional products.
Multi-purpose Tray
1
Remove the paper that is not jammed from the multi-purpose tray.
1 Open the upper right cover.
2 Remove all of the paper
that is not jammed from the
multi-purpose tray.
123
Troubleshooting
When the Paper Deck Unit-A1/Paper Deck Unit-D1 is attached, move the Paper Deck Unit-A1/Paper Deck Unit-D1 away from the
main unit beforehand.
2
Remove any jammed paper from the upper right cover.
1 Remove any jammed paper.
2 Close the upper right cover.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
When the Paper Deck Unit-A1/Paper Deck Unit-D1 is attached, reconnect the Paper Deck Unit-A1/Paper
Deck Unit-D1 to the main unit.
3
Follow the instructions on the screen.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
Paper Drawers 3 and 4
1
124
Remove any paper jammed in the paper drawer.
1 Press the open button of the
paper drawer that is feeding
the paper.
2 Grip the handle, and pull
out the paper drawer until it
stops.
3 Remove any jammed paper.
2
Gently push the paper drawer back into the machine until it clicks into place in
the closed position.
3
Follow the instructions on the screen.
When returning the paper drawer to its original position, be careful not to get your fingers
caught, as this may result in personal injury.
Troubleshooting
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
Paper Drawers (Right/Left)
1
Pull out the paper drawer.
1 Press the open button of the
paper drawer that is feeding
the paper.
2 Pull out the paper drawer
until it stops.
If the paper drawer seems to be stuck, do not pull it out by force. Push it back into the machine, press the
release button again, and then pull it back out.
125
2
Remove any jammed paper, and push the paper drawer back into the machine.
1 Remove any jammed paper.
2 Gently push the paper
drawer back into the
machine until it clicks into
place in the closed position.
When returning the paper drawer to its original position, be careful not to get your fingers
caught, as this may result in personal injury.
3
126
Follow the instructions on the screen.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
Paper Deck Unit-A1/Paper Deck Unit-D1 (Optional)
Paper Deck Unit-A1 and Paper Deck Unit-D1 are optional product.
1
Move the paper deck away from the main unit.
2
Remove any paper jammed in the side of the paper deck.
Troubleshooting
1. Press the release button.
2. Move the paper deck away
from the main unit.
Paper can also be jammed in the feeding slot on the side of the main unit. Remove any jammed paper from the
feeding slot.
127
3
Reconnect the paper deck to the main unit.
If the paper jam message is no longer displayed when you reconnect the paper deck, proceed to
step 7.
When reconnecting the paper deck to main unit, be careful not to get your fingers caught, as this
may result in personal injury.
4
Open the paper deck.
1 Press the open button.
2 Open the paper deck.
The inside lifter automatically
descends to the paper loading
position.
If the machine is in the Sleep mode (the touch panel is not displayed, and only
(Energy Saver)is lit), you
may be unable to open the paper deck unit. In this case, press
(Energy Saver)to reactivate the machine,
and then press the open button on the paper deck unit.
5
Remove any jammed paper.
Look carefully, as jammed paper may be difficult to see.
128
6
Close the paper deck.
7
Follow the instructions on the screen.
When closing the paper deck, be careful not to get your fingers caught, as this may result in
personal injury.
Troubleshooting
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
129
Procedure to Remove the Jammed Paper Effectively from the Paper Drawers
If a paper jam occurs in the paper drawers and you do not perform correct operations, paper jam may occur continuously. This
section explains how to clear the paper jam effectively in the paper drawers.
: Do not apply (OK)
: Apply (No Good (NG))
A paper jam occurs.
1.
Check that there is a problem with paper.
● Paper is loaded diagonally.
● Paper appears dirty and has tears.
● Several sheets of paper are attached.
● Paper is already curled.
Step 3
● Align the edges of paper and reload it.
● Remove the paper with a problem.
 Check that the machine operates normally.
Finish
3.
Fan all four borders of paper well.
Check that the machine operates normally.
Finish
4.
Check that the paper stack is not curled.
Turn the paper stack over and check that the paper stack is not curled
to the opposite direction.
Step 7
5.
Turn the paper stack over and reload it.
 Check that the machine operates normally.
Finish
6.
Gently bend the paper in the direction opposite to the curl.
Reload the paper with less than ±1/5” (5 mm) curls.
 Check that the machine operates normally.
Finish
2.
7.
130
Use a new paper stack or change the paper type.
Duplex Color Image Reader Unit-G1 (Optional)
Check the location of the paper jam, and follow the procedure described below, while referring to the directions that appear on
the touch panel display, to remove the jammed original.
The Duplex Color Image Reader Unit-G1 is an optional product.
2
Remove any originals from the feeder cover.
3
Open the inner cover, holding it by its front tab.
Troubleshooting
1
Remove originals from the original supply tray.
1. Pull the lever, and open the feeder
cover.
2. Remove any jammed originals.
If there is difficulty in removing jammed
paper, do not try to remove it forcibly, and
proceed to step 3.
131
4
Turn the green feed dial, and remove any jammed originals.
5
Close the inner cover and the feeder cover.
1. Turn the green feed dial.
2. Remove any jammed originals.
1. Close the inner cover.
2. Close the feeder cover.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
132
6
Remove any jammed originals from the feeder.
1 Lift the feeder.
2 Remove any jammed originals.
3 Close the feeder.
Troubleshooting
• When closing the feeder, be careful not to get your fingers caught, as this may result in personal
injury.
• Be aware that the light emitted from the platen glass may be very bright when closing the
feeder.
If there is difficulty in removing jammed paper, close the feeder and open the feeder cover and the inner
cover, and then proceed to step 4.
7
Follow the instructions on the screen.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
133
Document Insertion/Folding Unit-H1/Document Insertion
Unit-L1 (Optional)
If a paper jam occurs inside Document Insertion/Folding Unit-H1 or Document Insertion Unit-L1, a screen prompting you to
remove the jammed paper appears on the touch panel display. Check the location of the paper jam, and follow the procedure
described below, while referring to the directions that appear on the touch panel display, to remove the jammed paper.
• The insertion unit of the Document Insertion/Folding Unit-H1 or the Document Insertion Unit-L1 may interfere with the
External 2/3 Hole Puncher-A1 or the finisher when clearing jams. Lift up the insertion unit before removing jams from the
External 2/3 Hole Puncher-A1 or the finisher.
• Take care when handling the optional equipment that is attached to the machine. When an optional unit’s cover is opened to
replace a staple cartridge and a staple case, discard the punch waste, or clear paper or staple jams, prints may still be output if
other optional units are operating normally, and are not involved in the paper or staple jam removal procedure.
The Document Insertion/Folding Unit-H1, Document Insertion Unit-L1, and External 2/3 Hole Puncher-A1 are optional products.
Insertion Unit
1
134
Open the top cover of the Document Insertion/Folding Unit-H1 or Document
Insertion Unit-L1.
2
Remove any jammed paper from the top cover.
1 Remove the paper that is
not jammed.
2 Remove any jammed
paper.
3 Close the top cover.
Troubleshooting
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
3
Open the front cover and the insertion unit.
1 Open the front cover.
2 Open the insertion unit.
135
4
Remove any jammed paper from the delivery unit.
1. Open the delivery unit.
2. Remove any jammed
paper.
3. Close the delivery unit.
When closing the delivery unit, be careful not to get your fingers caught, as this may result in
personal injury.
5
Close the insertion unit and the front cover.
1 Close the insertion unit.
2 Close the front cover.
When closing the insertion unit and the cover, be careful not to get your fingers caught, as this
may result in personal injury.
6
136
Follow the instructions on the screen.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
Inside the Insertion Unit
2
Open the upper delivery guide.
3
Remove any jammed paper.
Troubleshooting
1
Open the front cover of the Document Insertion/Folding Unit-H1 or Document
Insertion Unit-L1.
137
4
Close the upper delivery guide.
When closing the guide, be careful not to get your fingers caught, as this may result in personal
injury.
5
138
Open the lower delivery guide.
6
Remove any jammed paper from the lower delivery guide.
1 Remove any jammed
paper.
2 Close the lower
delivery guide.
Troubleshooting
When closing the guide, be careful not to get your fingers caught, as this may result in personal
injury.
7
Close the front cover.
8
Follow the instructions on the screen.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
139
Folding Unit
1
Open the front cover of the Document Insertion/Folding Unit-H1.
2
Open the lower delivery guide.
3
Pull out the folding unit.
140
4
Remove any jammed paper from the exit slot.
5
Remove any jammed paper from the left guide.
1 Push out any jammed
paper toward the exit
slot.
2 Remove any jammed
paper.
Troubleshooting
1 Open the left guide.
2 Remove any jammed
paper from the inside
guide.
3 Remove any jammed
paper from the
outside guide.
141
6
Remove any jammed paper from the right guide.
1 Open the right guide.
2 Remove any jammed
paper.
3 Close the right guide.
When closing the guide, be careful not to get your fingers caught, as this may result in
personal injury.
7
Close the left guide, and return the folding unit to its original position.
1 Close the left guide.
2 Return the folding
unit to its original
position.
When closing the guide and returning the unit to its original position, be careful not to get
your fingers caught, as this may result in personal injury.
142
8
Close the lower delivery guide and the front cover.
1 Close the lower
delivery guide.
2 Close the front cover.
Troubleshooting
When closing the guide and cover, be careful not to get your fingers caught, as this may
result in personal injury.
9
Follow the instructions on the screen.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the
paper jam is cleared.
143
External 2/3 Hole Puncher-A1
If a paper jam occurs inside the puncher, a screen prompting you to remove the jammed paper appears on the touch panel
display. Check the location of the paper jam, and follow the procedure described below, while referring to the directions that
appear on the touch panel display, to remove the jammed paper.
The External 2/3 Hole Puncher-A1 is an optional product.
1
Open the front cover of the puncher waste tray.
2
Set the green knob to the fixed position.
144
3
Open the front cover of the finisher.
Troubleshooting
*1
*2
*1 Booklet Finisher-P1
*2 Staple Finisher-P1
If the Document Insertion/Folding Unit-H1 or Document Insertion Unit-L1 is attached, open the insertion unit.
4
Open the top cover of the finisher.
If the Document Insertion/Folding Unit-H1 is attached, lift the insertion unit.
5
Open the delivery guide.
*
* Delivery Guide
145
6
Open the top cover of the puncher unit.
7
Remove any jammed paper from the puncher unit and the finisher.
8
Close the delivery guide.
When closing the guide, be careful not to get your fingers caught, as this may result in personal
injury.
146
9
Close the top cover of the finisher.
Troubleshooting
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
Close the covers.
10
1 Close the front cover of the
finisher.
2 Close the top cover of the
puncher unit.
If the Document Insertion/
Folding Unit-H1 or Document
Insertion Unit-L1 is attached to
the main unit, close the insertion
unit.
3 Close the front cover of the
puncher waste tray.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
Follow the instructions on the touch panel display.
11
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
147
Staple Finisher-P1/Booklet Finisher-P1 (Optional)
If a paper jam occurs in the Staple Finisher-P1 or Booklet Finisher-P1, a screen prompting you to remove the jammed paper
appears on the touch panel display. Check the location of the paper jam, and follow the procedure described below, while
referring to the directions that appear on the touch panel display, to remove the jammed paper.
The Staple Finisher-P1, Booklet Finisher-P1, Document Insertion/Folding Unit-H1, and Document Insertion Unit-L1 are optional
products.
Inside the Top Cover
1
Open the front cover of the finisher.
*1
*2
*1 Booklet Finisher-P1
*2 Staple Finisher-P1
If the Document Insertion/Folding Unit-H1 or Document Insertion Unit-L1 is attached, open the
insertion unit.
2
148
Open the top cover of the finisher.
3
Remove any paper jammed from the top cover of the finisher.
1 Remove any jammed paper.
2 Close the top cover of the
finisher.
If you open the Document Insertion/
Folding Unit-H1 or Document
Insertion Unit-L1 in step 1, close the
insertion unit.
Troubleshooting
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
4
Close the front cover of the finisher.
5
Follow the instructions on the screen.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
149
Output Area
1
Open the output slot on the outside of the finisher, and remove any jammed
paper that is visible.
If you cannot see any jammed paper, check if any jammed paper is stuck inside the output area of
the finisher.
1 Open the output slot.
2 Remove any jammed paper.
3 Close the output slot.
If a paper jam occurs when you are printing in the Staple mode, do not remove the output sheets that are
waiting to be stapled. (Printing and stapling resume after you clear the paper jam.)
2
Open the front cover of the finisher.
*1
*2
*1 Booklet Finisher-P1
*2 Staple Finisher-P1
If the Document Insertion/Folding Unit-H1 or Document Insertion Unit-L1 is attached, open the
insertion unit.
150
4
Open the delivery guide.
5
Remove any jammed paper.
Troubleshooting
3
Open the top cover of the finisher.
151
6
Close the delivery guide.
When closing the delivery guide, be careful not to get your fingers caught, as this may result in
personal injury.
7
Close the top cover and front cover of the finisher.
1 Close the top cover.
If you open the Document
Insertion/Folding Unit-H1 or
Document Insertion Unit-L1 in
step 2, close the insertion unit.
2 Close the front cover.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
8
152
Follow the instructions on the screen.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
Front Cover of the Booklet Finisher-P1
1
Open the front cover of the finisher.
Troubleshooting
If the Document Insertion/Folding Unit-H1 or Document Insertion Unit-L1 is attached, open the
insertion unit.
2
Open the top cover of the finisher.
153
3
Remove any jammed paper from the upper delivery guide.
1 Tilt the upper delivery guide to
the right.
2 Remove any jammed paper.
When releasing the upper delivery guide, be careful not to get your fingers caught, as this may
result in personal injury.
Springs are attached to the upper delivery guide, so it returns to its original position when released.
4
Remove any jammed paper from the lower delivery guide.
1 Tilt the lower delivery guide to
the right.
2 Remove any jammed paper.
3 Return the lower delivery guide
to its original position.
When releasing the upper delivery guide, be careful not to get your fingers caught, as this may
result in personal injury.
154
5
Close the top cover and front cover of the finisher.
1 Close the top cover of the
finisher.
If you open the Document Insertion/
Folding Unit-H1 or Document
Insertion Unit-L1 in step 1, close the
insertion unit.
2 Close the front cover of the
finisher.
Troubleshooting
When closing the covers, be careful not to get your fingers caught, as this may result in personal
injury.
6
Follow the instructions on the screen.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
Saddle Stitcher Unit of the Booklet Finisher-P1
1
Open the front cover of the finisher.
155
2
Turn the small knob on the right in the direction of the arrow
(counterclockwise).
3
While pushing in the larger knob on the left, turn it in the direction of the arrow
(clockwise).
4
Remove any jammed paper protruding from the saddle stitcher unit.
156
5
Remove any jammed paper from the lower delivery guide.
1 Tilt the lower delivery guide to
the right.
2 Remove any jammed paper.
3 Return the lower delivery guide
to its original position.
Troubleshooting
When returning the lower delivery guide to its original position, be careful not to get your fingers
caught, as this may result in personal injury.
6
Close the front cover of the finisher.
7
Follow the instructions on the screen.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
157
Copy Tray-Q1 (Optional)
If a paper jam occurs inside the Copy Tray-Q1, a screen similar to the one shown below appears on the touch panel display.
Check the location of the paper jam, and follow the procedure described below, and the procedure that appears on the touch
panel display, to remove the jammed paper.
The Copy Tray-Q1 is an optional products.
1
Remove the outputted paper from the output tray.
2
Remove any jammed paper.
If you pull the jammed paper gently and you can pull out, remove the paper.
If you pull jammed paper gently and fail to pull out, proceed to the next step. Do not pull out jammed
paper by force, as this may leave torn pieces inside the machine and cause the machine to malfunction.
158
3
Open the front cover of the main unit, and pull out the fixing transport unit.
4
Remove any jammed paper from the left guide.
5
Remove any jammed paper from the fixing unit.
1 Open the front cover.
2 Move the green lever in the
direction of the arrow.
3 Pull out the fixing transport unit.
Troubleshooting
1 Open the left guide.
2 Remove any jammed paper.
If you cannot pull out the jammed paper, proceed to the next step. Do not pull out jammed paper by force,
as this may leave torn pieces inside the machine and cause the machine to malfunction.
159
6
Remove any jammed paper from the lower guide.
1 Open the lower guide, holding
by the green tab.
2 Remove any jammed paper.
3 Close the lower guide.
When closing the guide, be careful not to get your fingers caught, as this may result in personal
injury.
7
Remove any jammed paper from the fixing unit.
1 Pull the paper gently.
2 Turn the knob to the left to
remove any jammed paper.
3 Close the left guide.
When closing the guide, be careful not to get your fingers caught, as this may result in personal
injury.
160
8
Push the fixing transport unit back into its original position, and close the front
cover.
1 Push the fixing transport unit
back into its original position.
2 Return the green lever to its
original position.
3 Close the front cover.
Troubleshooting
When closing the cover and returning the unit to its original position, be careful not to get your
fingers caught, as this may result in personal injury.
9
Follow the instructions on the touch panel display.
The screen indicating the directions on how to clear the paper jam is displayed repeatedly until the paper
jam is cleared.
161
Reducing the Frequency of Paper
Jams
If paper jams occur frequently, even though there is no apparent problem with the machine, either one of the following two
reasons may be the cause. Follow the instructions described below to reduce the frequency of paper jams.
● There are torn pieces of paper left inside the machine.
Pulling jammed paper out of the machine by force may leave parts of the paper torn inside, leading to frequent paper
jams. If paper tears while you are trying to remove jammed paper from the machine, make sure that you remove all of the
torn pieces.
● The paper loaded in the paper drawer differs from the setting.
Make sure that the paper loaded in the paper drawer matches the paper size/type registered in [Paper Settings] in
[Preferences] (Settings/Registration).
162
Clearing Staple Jams (For
Optional Products)
If a staple jam occurs, a screen indicating the location of the staple jam and how to clear the jam appears on the touch panel
display. Follow the instructions on the screen to clear the staple jam. The screen is displayed repeatedly until the staple jam
is cleared. If you press [Close], you can continue operations, such as setting modes or scanning originals, even if the jammed
staple is not removed immediately.
Troubleshooting
Locations of Staple Jams
For information on the parts of the machine in which staple jams occur and instructions on clearing staple jams, see the
following.
Saddle Stitcher Unit of the
Booklet Finisher-P1 (p. 166)
Stapler Unit of the Staple
Finisher-P1/Booklet Finisher-P1
(p. 164)
B
A
163
Stapler Unit of the Staple Finisher-P1/Booklet Finisher-P1
Check the location of the staple jam, and follow the procedure described below, while referring to the directions that appear on
the touch panel display, to remove the jammed staple.
Make sure to close all covers and paper drawers of the machine before clearing any staple jams.
The Staple Finisher-P1 and Booklet Finisher-P1 are optional products.
1
Open the front cover of the finisher.
*1
*2
*1 Booklet Finisher-P1
*2 Staple Finisher-P1
2
164
Lift and pull out the staple case from the stapler unit, holding it by the green
tab.
3
Remove any staples jammed in the staple case.
3
2
1
1. Push down the tab on the
staple case.
2. Remove all of the staples
that slide from the staple
cartridge.
3. Return the tab on the staple
case to its original position.
5
Close the front cover of the finisher.
Troubleshooting
4
Gently push the staple case back into the finisher and push down firmly until it
is securely in place.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
After the cover is closed, the stapler unit may automatically perform a “dry” stapling operation to reposition
the staples.
165
Saddle Stitcher Unit of the Booklet Finisher-P1
Check the location of the staple jam, and follow the procedure described below, while referring to the directions that appear on
the touch panel display, to remove the jammed staple.
• Make sure to close all covers and paper drawers of the machine before clearing any staple jams.
• Before clearing a staple jam in the saddle stitcher unit, remove all paper that has been output to the booklet tray.
The Booklet Finisher-P1 is an optional product.
1
Open the front cover of the finisher.
2
Pull out the saddle stitcher unit.
*1
*1 Stapler Unit of the Saddle Stitcher Unit
*2 Saddle Stitcher Unit
166
*2
1 Grip the handle of the
saddle stitcher unit, and
pull out until it stops.
2 Pull the stapler unit of
the saddle stitcher unit
towards you, and then
push it up.
4
Push up the tab on the staple case.
Troubleshooting
3
Pull out the staple cartridge containing the jammed staples, holding it by its
left and right sides.
1 Push down Part A to
unlock.
2 Push up Part B.
B
A
5
Remove any jammed staples.
1 Remove any jammed
staples.
2 Return Part B to its
original position.
B
167
6
Return the staple case to its original position.
Push the staple case in until it clicks into place.
7
Gently push the saddle stitcher unit back into its original position.
1 Pull the stapler unit
towards you, and then
push it down into its
original position.
2 Grip the handle of the
saddle stitcher unit, and
return it to its original
position.
When returning the saddle stitcher unit to its original position, be careful not to get your fingers
caught, as this may result in personal injury.
8
Close the front cover of the finisher.
When closing the cover, be careful not to get your fingers caught, as this may result in personal
injury.
When you have cleared the staple jam, be sure to manually reposition the staples in the saddle stitcher
unit. (See e-Manual > Settings/Registration.)
168
If Memory Becomes Full During
Scanning
The machine’s memory can store up to approximately 20,200 pages of scanned images. Approximately 20,000 pages of that
total is shared by the various functions, including the Copy; Fax; Scan and Send; Scan and Store (Store in Mail Box); Fax/I-Fax
Inbox; and, printing from computer functions. In addition, each function is guaranteed to be able to store the following number
of pages:
For example, the Copy function can store up to approximately 20,100 pages of scanned images.
20,000 + 100 = 20,100 pages (approximate figures)
However, the number of pages that the machine’s memory can store may differ, depending on the amount of memory required
for files stored in the Mail Box and Fax/I-Fax Inbox, and jobs that are in the print queue.
If memory becomes full during the scanning of originals, a message will appear on the touch panel display.
• When using Fax/Scan and Send, you can send up to 999 pages at one time.
• Delete any unnecessary files in the Mail Box and Fax/I-Fax Inbox to free up memory.
For the Copy Function
Follow the directions below based on the message that appears on the touch panel
display.
● If the message <Scanning will be canceled because the memory is full. Do you want to print the
scanned pages?> appears:
Select [Yes] or [No].
[Yes]:
[No]:
The pages scanned into memory are printed. When printing is complete, scan the remaining originals.
The pages scanned into memory are not printed.
● If the message <Scanning will be canceled because the memory is full. Wait a moment, then try again.>
appears:
Select [OK].
[OK]:
Returns to the Basic Features screen of the function you are using. Scan the job again when the current job is
complete.
For the Fax/Scan and Send Function
Follow the directions below based on the message that appears on the touch panel
display.
● If the message <Scanning will be canceled because the memory is full. Do you want to send the
scanned pages?> appears:
Select [Yes] or [No].
[Yes]:
[No]:
The pages scanned into memory are sent. When storing is complete, scan the remaining originals.
The pages scanned into memory are not sent.
169
Troubleshooting
Copy: 100 pages
Print From Computer: 100 pages (excluding Secure Print jobs)
For the Scan and Store Function
Follow the directions below based on the message that appears on the touch panel
display.
● If the message <Scanning will be canceled because the memory is full. Do you want to store the
scanned pages?> appears:
Select [Yes] or [No].
[Yes]:
[No]:
The pages scanned into memory are stored. When storing is complete, scan the remaining originals.
The pages scanned into memory are not stored.
● If the message <Scanning will be canceled because the memory is full. Wait a moment, then try again.>
appears:
Select [OK].
[OK]:
170
Returns to the Basic Features screen of the function you are using.
When an Error Message Is
Displayed
Error messages may appear on the touch panel display of the machine or the Web browser.
Self-diagnostic error messages appear in the following cases:
Troubleshooting
● When scanning or printing cannot be performed because of an operational error
● When you need to make a decision or take some action during scanning or printing
● When you need to make a decision or take some action while browsing the network
Example of an Error Message on the Touch Panel Display
Example of an Error Message on the Web Browser
For information on error messages and instructions on resolving errors, see e-Manual > Problem Solving.
171
When an Error Code Is Displayed
If a job or operation does not complete successfully, the error code is displayed on the Details screen for Log on the Status
Monitor/Cancel screen.
You can check the error code in the following locations:
● Details screen for Log on the Status Monitor/Cancel screen:
When a job or operation is not completed normally:
● Results row of the Communication Management Report:
If an error occurs during a send, receive, or fax job, the error code is printed.
04/12/2012
iRADVXXXX
DEVICE INFORMATION COMMUNICATION LOG REPORT
START TIME
END TIME
TYPE
DELIVER
DELIVER
DELIVER
DELIVER
TO/FROM
DATA DETAILS
RESULT
DEPT.ID
ADDRESS BOOK
DEPT.ID
ADDRESS BOOK
DEPT.ID
ADDRESS BOOK
DEPT.ID
ADDRESS BOOK
For information on error codes and instructions on resolving errors, see e-Manual > Problem Solving.
172
Printer/Fax Driver
Troubleshooting
See “Troubleshooting” in the driver help to resolve problems when using the printer driver or fax driver for Windows.
The following screens indicate the directions on how to display “Troubleshooting” from the screen for the printer driver.
The screens may differ, depending on the operating system, and the type and version of the printer driver you are using.
Troubleshooting
173
Service Call Message
If a malfunction occurs and the machine cannot operate normally, a screen prompting you to contact your local authorized
Canon dealer is displayed.
If a screen such as the one above is displayed, contact your local authorized Canon dealer. (See “Contacting Your Local
Authorized Canon Dealer,” on p. 175.)
If a screen such as the one below is displayed and the print or scan function does not operate normally, some functions may
still be available.
● When [Limited Functions Mode] Is Displayed:
If [Limited Functions Mode] is displayed, you can temporally set the Limited Functions Mode to continue to use the
machine until the cause of the malfunction is cleared. For more information, see “Setting the Limited Functions Mode from
the Service Call Message Screen,” on p. 177.
● When a Service Call Message Is Displayed on the Bottom of the Screen:
Even if a message prompting you to call your service representative appears on the bottom of the screen, some functions
may still be available.
For more information, see “Functions Available When the Printer/Scanner Cannot Be Used Due to an Error,” on p. 178.
174
Contacting Your Local Authorized Canon Dealer
If a screen prompting you to contact your local authorized Canon dealer is displayed, follow the procedure described below.
1. Open the main power switch
cover.
2. Press the main power switch
to the “ ” side.
3. Close the main power switch
cover.
If you turn OFF the main power switch when there is a job waiting to print, that job is erased.
2
Wait at least 10 seconds after the Main Power Indicator is turned off, and then
turn the main power switch back to ON.
1. Open the main power switch
cover.
2. Press the main power switch
to the “I” side.
3. Close the main power switch
cover.
175
Troubleshooting
1
Turn OFF the main power of the main unit.
3
If the machine still does not operate normally, follow the procedure below, and
then contact your local authorized Canon dealer.
1. Turn the main power switch OFF.
2. Remove the power plug from the power outlet.
Do not connect or disconnect the power cord with wet hands, as this may result in electrical
shock.
Always grasp the power plug when disconnecting the power cord. Pulling on the power cord may
expose or snap the core wire, or otherwise damage the power cord. If the power cord is damaged,
this could cause current to leak, resulting in a fire or electrical shock.
When you contact your local authorized Canon dealer, have the following information available:
• Product name
• Details of the malfunction
• The error code displayed on the touch panel display
176
Setting the Limited Functions Mode from the Service Call
Message Screen
When [Limited Functions Mode] is displayed, follow the procedures below.
If you turn OFF the main power switch when there is a job waiting to print, that job is erased.
1
Troubleshooting
If you set Limited Functions Mode to ‘On’ from the Service Call Message screen, [Limited Functions Mode] in [Management
Settings] (Settings/Registration) is also set to ‘On’. (See e-Manual > Security.)
Press [Limited Functions Mode]  [Yes].
A message prompting you to restart the machine (turning the main power switch OFF, and then
ON) appears.
2
Turn OFF the main power of the main unit.
3
Wait at least 10 seconds after the Main Power Indicator is turned off, and then
turn the main power switch back to ON.
1. Open the main power switch
cover.
2. Press the main power switch
to the “ ” side.
3. Close the main power switch
cover.
1. Open the main power switch
cover.
2. Press the main power switch
to the “I” side.
3. Close the main power switch
cover.
The machine starts up in the Limited Functions mode.
177
Functions Available When the Printer/Scanner Cannot Be Used
Due to an Error
You can use the following functions even when the Print and Scan functions are restricted:
● Main Menu Screen
: Available
-: Unavailable
Available Functions
Copy
When the Print function is
restricted
When the Scan function is
restricted
-
-
Fax
*1
Scan and Send
-
Scan and Store
*2
Access Stored Files
-
Fax/I-Fax Inbox
-
Secure Print
-
*3
Remote Scan
-
Web Access
Shortcut to Settings/Registration
-
-
-
-
Tutorial
Workflow Composer
Document Scan Code Analyzer
for MEAP*4
-
Other MEAP Applications*5
● Control Panel
: Available
-: Unavailable
Available Functions
When the Print function is
restricted
When the Scan function is
restricted
Quick Menu*6
The Status Monitor/Cancel Screen
Settings/Registration
178
*7
-
-
● Operation From a Computer
: Available
-: Unavailable
Available Functions
When the Print function is
restricted
When the Scan function is
restricted
Remote UI
MEAP Application*5
Sending a fax from a computer is not available.
*2
[Print List] on the Mail Box Selection screen is not available.
*3
[Add Files (Scan and Store)] on the Edit File screen is not available.
*4
Document Scan Code Analyzer is included in the Document Scan Lock Kit. For more information, see e-Manual > Optional
Products.
*5
Available by installing each MEAP application. May not be available, depending on the restricted functions.
*6
The registered button may not be available, depending on the restricted functions.
*7
[Print List] on the Job Log screen and [Register] on the Consumable screen are not available.
Troubleshooting
*1
• A print job is automatically canceled when the Print function is restricted. A scan job is automatically canceled when the Scan
function is restricted.
• The machine may not enter the Sleep mode completely when a function is restricted due to an error.
If the target function is restricted due to an error, the function is not available when you use the shortcut key on the top of the
Main Menu screen or when you use the Quick Menu.
179
Frequently Asked Questions
This section includes frequently asked questions and answers regarding the machine. Use this section if you have trouble using the
machine.
Question
Applicable Page
Q1
I want to make a rush copy, but I cannot because of the long copy job.
p. 182
Q2
When copying, the Scan screen for the next document is displayed. Is there a way to not display this screen?
p. 182
Q3
Can a mark be applied to the document that has been scanned?
p. 183
Q4
Do I need to enter the address of the recipient every time?
p. 183
Q5
Can I send a fax to multiple destinations?
p. 184
Q6
Can you give me information on how to send to the SMB server and specify its settings?
p. 185
Q7
Can I move the Address Book registered on another Canon machine onto this machine?
p. 187
Q8
Can I forward the data received via fax/I-fax?
p. 187
Q9
When sending a fax, can the machine be set so that the sender’s fax number and name be displayed?
p. 188
Q10
How do I change the default settings (scan settings and file format) of the Scan and Send Basic Features screen?
p. 188
Q11
Is there a way to prevent a transmission error when sending a facsimile to a new destination?
p. 189
Q12
The quality of the image sent by fax is not good.
p. 190
Q13
How can I make use of multiple telephone lines?
p. 190
Q14
How do I register/edit destinations in a one-touch button?
p. 191
Q15
Can I add an arbitrary subject when sending e-mail?
p. 192
Q16
How do I change the storage period for the scanned file stored in the Mail Box?
p. 192
Q17
How do I access the Advanced Box from a computer?
p. 193
Q18
How do I forward received data to the Advanced Box?
p. 193
Q19
How do I set to create a booklet with a file in a mail box?
p. 194
Q20
I cannot print PDF files stored in the Advanced Box. Are optional products required?
p. 194
Q21
When printing from the computer, booklet was not made even though saddle stitch booklet mode was set.
p. 194
Q22
The content of the reverse side appears on the copies.
p. 195
Q23
The printed paper appears dirty. Also, the color appears to be different from the original.
p. 196
Q24
The printed paper is warped.
p. 196
Q25
I had printed from the computer, but I did not find the output. I am afraid that someone may have taken it by mistake.
p. 197
Q26
Can I specify the scan settings from the computer and then store for the original loaded in the machine?
p. 197
Q27
Can I make copies or send a facsimile of different size originals at the same time?
p. 198
Q28
Can I print on the reverse side of the preprinted paper?
p. 199
180
Question
Applicable Page
Can I output paper to a different tray according to the function?
p. 199
Q30
What are the types of paper that I can use?
p. 200
Q31
How do I print data received via fax/I-fax on paper specified in advance?
p. 200
Q32
How can I manage documents that failed to be forwarded?
p. 201
Q33
When a fax fails to be sent, both the TX Report and the Fax TX Report are output. Is there a way to not output the Fax
TX Report?
p. 201
Q34
How do I print the data received from specific destinations only?
p. 202
Q35
What is the model number of the staple cartridge for the finisher or the stamp cartridge for the feeder?
p. 202
Q36
A paper jam has occurred. How do I solve this problem?
p. 203
Q37
Numbers, such as #751 and #801 are displayed on the touch panel display. What do they mean?
p. 204
Q38
I cannot print from the computer. Did the machine malfunction?
p. 204
Q39
It seems as though turning OFF the machine is different from the previous imageRUNNER. I am afraid that this may be
a wrong operation.
p. 205
Q40
The touch panel display is completely black.
p. 205
Q41
I have just sent an important document via facsimile. Can I check to make sure that it was sent correctly?
p. 206
Q42
Can I restrict the number of copies/prints?
p. 206
Q43
Can I change the language displayed on the touch panel display?
p. 207
Q44
Can I change the screen or the order that the functions are displayed on the touch panel display when the power is
turned ON?
p. 208
Q45
I want to check the IP address for this machine to run the Remote UI, but I do not know how to check it.
p. 209
Q46
Can I change the default settings of the printer driver?
p. 210
Q47
Is there a way to adjust the sound heard when fax sending/receiving is complete?
p. 211
Q48
What is MEAP?
p. 212
Troubleshooting
Q29
181
Q&A
2
1
I want to make a rush copy, but I
When copying, the Scan screen for
cannot because of the long copy
the next document is displayed.
job.
Is there a way to not display this
screen?
You can temporarily stop the
current copy job and give priority
When [Job Build] is set, the Scan
to a rush copy by using the
screen for the next document is
Interrupt mode. You can also give
displayed. By canceling the [Job
priority to a rush copy/print from
Build] setting, the screen is not
the Status Monitor/Cancel screen.
displayed.
■ Interrupt Function:
1. Press [Copy]  [Interrupt].
2. Set the desired copy mode.
■ Canceling the Job Build mode
1. Press [Copy]  [Options]  [Job Build].
2. Press [Close].
■ Interrupt/Priority Print
Function:
1. Press
(Status Monitor/Cancel).
2. Press [Copy/Print]  [Job Status] from
the [Print] drop-down list.
3. Select the job  press [Interrupt/Priority
Print].
4. Press [Interrupt and Print].
Additional Information
You can scan the original even if the
machine is waiting or printing (Reserved
Copying). For more information, see
e-Manual > Copy.
182
Q&A
Additional Information
The Job Build mode is useful if you cannot
load the originals all at once. This mode
enables you to divide the originals into
several parts, scan them, and then print
them all together.
After the original is sent, you can also
send a job done notice to the specified
e-mail address (Job Done Notice). For more
information, see e-Manual > Scan and Send,
or Fax.
Troubleshooting
3
Additional Information
4
Can a mark be applied to the
Do I need to enter the address of
document that has been scanned?
the recipient every time?
The machine can print a stamp on
You can store frequently used
the scanned document by using
destination in the Address
the Stamp mode.
Book. If the destination is stored
beforehand, you do not need to
enter the destination every time.
Position at which
stamp is applied
Vertical Placement
■ Storing from the Remote UI:
1. Click [Address Book]  select the
destination to register.
2. Click [Register New Destination] 
select the type of destination  enter
necessary items.
3. Click [OK].
Position at which
stamp is applied
Horizontal Placement
■ Setting procedure:
1. Press [Scan and Send] or [Fax] 
[Options].
2. Press [Finished Stamp]  [Close].
183
Q&A
■ Storing from the Touch Panel
Display:
1. Press [Scan and Send] or [Fax] 
[Address Book]  [Register/Edit].
2. Press [Register New Dest.]  enter
information following the instructions
on the touch panel display  press [OK].
5
Can I send a fax to multiple
destinations?
You can send a fax to multiple
destinations at the same time
using the following methods.
■ Specifying Multiple
Destinations from the Fax
Screen
1. Enter a fax number using
(numeric keys),
, or
 press [OK].
2. Continue entering the other fax numbers
 press [OK].
3. Press
Additional Information
You can also store frequently used
destination as a one-touch button on the
Scan and Send Basic Features screen or
the Fax Basic Features screen. For more
information, see e-Manual > Scan and Send,
or Fax.
184
(Start).
■ Specifying Multiple
Destinations from the Address
Book
1. Press [Fax]  [Address Book]  select
multiple destinations  press [OK].
2. Press
(Start).
Q&A
■ Registering Multiple
Destinations from the Address
Book as a Group Destination
and Selecting a Group
Destination
Can you give me information on
Registering a group destination in the
Address Book
1. Press [Address Book]  [Register/Edit] 
[Register New Dest.].
2. Press [Group]  enter the name and
register the group in the Address Book.
3. Press [Add from Address Book]  select
the addresses to register.
4. Press [OK]  [OK].
You can specify the settings using
2. Press
(Start).
Additional Information
• You cannot specify destinations registered
in the address book and destinations
registered in a one-touch button at the
same time.
• You can also register a group destination
in a one-touch button to send to multiple
destinations at the same time. For
information on registering one-touch
buttons, see e-Manual > Scan and Send,
or Fax.
how to send to the SMB server and
specify its settings?
Troubleshooting
Selecting the group destination as a
destination
1. Press [Address Book]  select the
registered group destination  press
[OK].
6
the following method.
■ Setting the Shared Folder on
the Computer-Side:
Using Windows 7
1. Right-click the new folder  click
[Property]  [Sharing].
2. Click [Sharing]  select the users you
want to authorize access.
3. Click [Add]  select [Read/Write] for
<Permission Level> for the added users.
4. Click [Sharing]  [End].
5. Click [Advanced Sharing]  select [Share
this folder]  click [Permission].
6. Select the users you want to authorize
access  select [Allow] for [Full Control].
7. Click [OK]  [OK]  [Close].
Using Windows Vista
1. Right-click the new folder  click
[Property]  [Sharing].
2. Click [Share]  select the users you want
to authorize access  click [Add].
3. Select [Co-owner] for <Permission Level>
for the added users  click [Share] 
[End].
4. Click [Advanced Sharing]  select [Share
this folder]  click [Permission].
5. Add the users you want to authorize
access  select [Allow] for [Full Control].
6. Click [OK]  [OK]  [Close].
Using Windows XP
1. Right-click the new folder  click
[Sharing and Security]  select [Share
this folder].
2. Click [Permissions]  select Everyone 
click [Delete].
3. Click [Add]  add the users you want
to authorize access  select [Allow] for
[Full Control].
4. Click [OK]  [OK]  [Close].
Using Windows 2000
1. Right-click the new folder  click
[Sharing]  select [Share this folder].
2. Click [Permissions]  select Everyone 
click [Delete].
3. Click [Add]  add the users you want
to authorize access  select [Allow] for
[Full Control].
4. Click [OK]  [OK].
185
Q&A
The item names may differ, depending on
the type of operating system you are using.
For more information, check the manual
documentation for the personal computer
operating system you are using.
■ Specifying the File Server by
Browsing:
1. Press [Scan and Send]  [New
Destination]  [File].
2. From the protocol drop-down list, press
[Windows (SMB)]  [Browse].
3. Select the work group name and file
server specify each settings  press
[OK].
Additional Information
■ Specifying the File Server on
the Touch Panel Display:
You can use the following procedure to
check the IP address of your computer.
Specifying the File Server by Host Search:
* The procedures may differ, depending on the
type of operating system you are using.
1. Press [Scan and Send]  [New
Destination]  [File].
2. From the protocol drop-down list, press
[Windows (SMB)]  press [Search Host].
3. On the search criteria screen, enter the IP
address for the computer you are using
 press [Start Searching].
4. Specify the file server  confirm the
settings  press [OK].
186
1. On the [Start] menu, click [Run]  enter
<cmd>.
2. Click [OK]  enter <ipconfig>  press
[ENTER] on the keyboard.
Q&A
8
7
Can I move the Address Book
Can I forward the data received via
registered on another Canon
fax/I-fax?
machine onto this machine?
You can use the import and export
settings, you can forward received
mode of the Remote UI to move
documents that matches the
the Address Book.
previously set conditions to the
■ Exporting the Address Book
from Another Canon Machine:
Confidential Fax Inbox of this
1. Click [Settings/Registration]  select
[Data Management] for <Management
Settings>.
2. Click [Address Lists] for <Import/Export
Individually>  [Export...].
3. Select the Address List and the format of
the file  click [Start Exporting].
4. Specify the location to store the file 
[Store].
Troubleshooting
If you specify the forwarding
machine, other machines, or the
file server.
Forward
* The key names may differ, depending on the type
of the model you are using.
■ Importing the Address Book to
the Machine:
1. Click [Settings/Registration]  select
[Data Management] for <Management
Settings>.
2. Click [Address Lists] for <Import/Export
Individually>  [Import...].
3. Select the file you want to import and
specify the desired settings  click [Start
Importing].
Confidential
Fax Inbox
■ Setting procedure:
1. Press
(Settings/Registration)
[Function Settings]  [Receive/Forward]
 [Common Settings].
2. Press [Forwarding Settings]  [Register]
 specify the forwarding conditions.
3. Press [Close].
Additional Information
• To perform this procedure, you must
have administrator privileges. For more
information, see e-Manual > Security.
• You can also export and import
forwarding settings. For more information,
see e-Manual > Remote UI.
187
Q&A
Additional Information
• To perform this procedure, you must
have administrator privileges. For more
information, see e-Manual > Security.
• If frequently used e-mail addresses are
stored in the Address Book, you can
specify the address quickly. For more
information, see e-Manual> Settings/
Registration.
Additional Information
For more information, see e-Manual >
Settings/Registration.
10
How do I change the default
settings (scan settings and file
format) of the Scan and Send Basic
9
Features screen?
When sending a fax, can the
machine be set so that the
sender’s fax number and name be
You can store the current settings
displayed?
as the default settings from
on
the Scan and Send Basic Features
screen.
After registering the sender’s
name, you can specify to print the
TX Terminal ID when sending a fax.
Date
Time
I-Fax Address
or
Fax Number
09/05/2012 TUE 15:00 FAX (404)XXX-XXXX
Sender's
Name (TTI)
Destination
Name
Page Number
CANON SALES
Atlanta office
001/001
Sender Information
■ Registering the sender’s name:
Before Change
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Send] 
[Fax Settings].
3. Press [Register Sender Name (TTI)] 
[Register/Edit]  enter the sender’s
name.
4. Press [OK].
■ Displaying/Printing the TX
Terminal ID:
1. Press [Fax]  [Options]  [Sender Name
(TTI)].
2. Select the sender’s name  press [OK].
188
After Change
Q&A
■ To register the settings as the
default settings:
1. Press [Scan and Send]  specify the scan
settings and the file format.
 [Change Default Settings]
2. Press
 [Yes].
11
Is there a way to prevent a
transmission error when sending a
facsimile to a new destination?
Troubleshooting
If [Confirm Entered Fax Number]
in
(Settings/Registration) is
set, a screen to enter the number
for confirmation is displayed. By
entering the number again, you
can reduce the risk of transmission
error.
■ Setting procedure:
Additional Information
For more information on each file format,
see e-Manual > Scan and Send.
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Send] 
[Fax Settings].
3. Press [Confirm Entered Fax Number] 
[On]  [OK].
Additional Information
• To perform this procedure, you must
have administrator privileges. For more
information, see e-Manual > Security.
• You can also restrict sending to a
destination that is not stored in the
Address Book. For more information, see
e-Manual > Security.
189
Q&A
Additional Information
12
The quality of the image sent by
fax is not good.
Change the scan type or settings
If [Register Options Shortcuts] is selected
from
, you can register the [Options]
shortcut button on the Fax Basic Features
screen.
13
according to the type of original.
How can I make use of multiple
Press [Preview] to check the
telephone lines?
document before sending.
■ Setting the Original Type and
Density settings:
Press [Fax]  [Options]  specify the
settings for [Original Type] or [Density].
Text/Photo Mode
Photo Mode
You can specify the settings using
the following method.
Text Mode
■ Selecting a telephone line when
sending:
1. Press [Fax]  [Options]  [Select Line].
2. Select the telephone line  press [OK]
 [Close].
■ Viewing the preview:
1. Press [Fax]  specify the destination.
2. Press [Options]  [Preview]  [Close].
3.Press
(Start).
■ Setting the sending and
receiving lines from [Select TX
Line]:
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Send] 
[Fax Settings].
3. Press [Set Line]  [Select TX Line]  set
the line to use for sending in [Priority
TX]  set the line to use for receiving in
[Prohibit TX].
4. Press [OK].
Preview Screen
190
Q&A
■ Setting forwarding conditions
for the receiving line:
1. Press [One-Touch]  [Register]  select
the button to register/edit.
2. Press [Register/Edit] register/edit the
address  press [Close].
Troubleshooting
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Receive/
Forward]  [Common Settings].
3. Press [Forwarding Settings]  select the
line from the <Receive> drop-down list
 select [Register]  set the forwarding
conditions.
4. Press [Close].
■ Registering/Editing from the
Scan and Send Screen
Additional Information
For more information on the forwarding
conditions, see e-Manual > Settings/
Registration.
Additional Information
14
How do I register/edit destinations
in a one-touch button?
Press
• For information on how to register/edit
a destination in a one-touch button, see
e-Manual > Scan and Send, or Fax.
• When registering from the Fax screen,
you can only register fax destinations or
groups that include fax destinations.
on the Fax screen or
[One-Touch] on the Scan and Send
screen.
■ Registering/Editing from the
Fax Screen
1. Press
 select the button to
register/edit  press [Register/Edit].
2. Register/edit the address  press
[Close].
191
Q&A
15
16
Can I add an arbitrary subject when
How do I change the storage
sending e-mail?
period for the scanned file stored
in the Mail Box?
You can enter an e-mail subject in
[Subject/Message] in [Options].
You can change the time until files
are automatically erased from [Set/
■ Setting procedure:
1. Press [Scan and Send]  specify the
destination  press [Options].
2. Press [Subject/Message]  enter the
subject.
3. Press [OK]  [Close].
Register Mail Boxes] in
(Settings/
Registration). Change the setting,
as necessary.
* You can set the time until the files are
automatically erased to 0 (none), 1, 2, 3, 6, 12
hours, 1, 2, 3, 7, 30 days. The default setting is
‘3’ days.
■ Setting procedure:
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Store/
Access Files]  [Mail Box Settings].
3. Press [Set/Register Mail Boxes]  select
the inbox number set the time until
files are automatically erased  press
[OK].
Additional Information
• You can also enter the message for the
e-mail in [Message].
• If you do not specify the subject, the string
registered in [Default Subject] in
(Settings/Registration) is inserted as the
subject. The default setting is ‘Attached
Image.’
Additional Information
In the Mail Box settings, you can also
register a name for the Mail Box and change
the password. For more information, see
e-Manual > Settings/Registration.
192
Q&A
18
How do I access the Advanced Box
How do I forward received data to
from a computer?
the Advanced Box?
If the Advanced Box is opened with
Specify an Advanced Box
SMB, check the following.
destination registered in the
■ Checking the settings for [Open
to Public]:
Address Book as the forwarding
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Store/
Access Files] [Advanced Box Settings].
3. Press [Open to Public]  check whether
[By SMB] is selected.
■ Registering an Advanced Box
Destination in the Advanced
Box:
Troubleshooting
17
destination.
1. Press
(Settings/Registration).
2. Press [Set Destination]  [Register
Destinations]  [Register New Dest.].
3. Press [File]  register the Advanced Box
destination.
■ Checking the settings for
[Prohibit Writing from External]:
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Store/
Access Files]  [Advanced Box Settings].
3. Check whether [Prohibit Writing from
External] is set to ‘Off’.
■ Registering an Advanced Box
Destination as a Forwarding
Destination:
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Receive/
Forward]  [Common Settings].
3. Press [Forwarding Settings]  [Register]
 specify the forwarding conditions.
4. Press [Forwarding Destination] 
[Address Book]  specify the Advanced
Box destination.
Additional Information
For more information, see e-Manual >
Security.
193
Q&A
Additional Information
Additional Information
• For information on registering an
Advanced Box destination in the Address
Book, see e-Manual > Scan and Send.
• For more information on forwarding
settings, see e-Manual > Settings/
Registration.
• For details on the Booklet mode settings,
see e-Manual > Access Stored Files.
• Use a document that was stored with the
[Booklet Scan] mode set.
• For details on the Booklet Scan mode
settings, see e-Manual > Scan and Store.
19
20
How do I set to create a booklet
I cannot print PDF files stored in
with a file in a mail box?
the Advanced Box. Are optional
products required?
You can create a booklet using
the Booklet mode. Specify the
The following optional products
following settings.
are required to print PDF files:
■ Setting procedure:
PS Printer Kit
Direct Print Kit (for PDF/XPS)
1. Press [Access Stored Files]  [Mail Box]
 select a stored document.
2. Press [Print]  [Change Print Settings] 
[Options].
3. Press [Booklet]  [Booklet Scan]  [Fold
+ Saddle Stitch].
4. Specify the cover settings, orientation,
and detailed settings  press [OK].
Additional Information
If you are using the PS Printer Kit, the Direct
Print Kit (for PDF/XPS) is unnecessary.
21
When printing from the computer,
booklet was not made even though
saddle stitch booklet mode was
set.
The Saddle Stitch mode cannot be
used if you exceed the maximum
number of sheets that can be
saddle stitched. In that case, you
can use the Divided Booklet mode.
194
Q&A
■ The maximum number of
sheets that can be saddle
stitched is:
The content of the reverse side
appears on the copies.
Troubleshooting
16 sheets (16 to 20 lb bond (60 to 80 g/m2))
10 sheets (21 to 28 lb bond (81 to 105 g/m2))
5 sheets (29 to 40 lb bond (106 to 150 g/m2))
4 sheets (56 lb cover to 110 lb index (151 to
209 g/m2))
If the number of sheets is more than the
number stated above, the output is printed
without being saddle stitched.
22
You can erase the background
color of the original and prevent
the original image on the reverse
■ Setting a Divided Booklet
(Windows):
Click [Booklet]  [Divide into Sets].
side of thin originals from
appearing on the copies by using
[Background Density].
Original
Copy
■ Setting procedure:
1. Press [Copy]  [Options]  [Density].
2. Press [Background Density]  [Auto] or
[Adjust].
• If [Auto] is pressed, the exposure of the
original image on the reverse side is
automatically adjusted.
• If [Adjust] is pressed, the exposure of the
original image on the reverse side can be
manually adjusted.
Additional Information
Additional Information
• You cannot set the Divided Booklet mode
from the Macintosh printer driver.
• For information on the number of sheets
that can be saddle stitched at one time,
see e-Manual > Optional Products/
Software.
For more information, see e-Manual > Copy.
195
Q&A
23
The printed paper appears dirty.
Also, the color appears to be
different from the original.
■ Automatic gradation
adjustment:
1. Press
(Settings/Registration).
2. Press [Adjustment/Maintenance] 
[Adjust Image Quality]  [Auto Adjust
Gradation].
3. [OK]  [Start Printing].
If streaks are printed on the paper
or the image is not printed evenly,
the inside of the feeder may be
dirty. Follow the procedure below
to clean the feeder. You can also
automatically correct the gradation
of the image from [Auto Adjust
Gradation].
■ Cleaning the feeder:
1. Press
(Settings/Registration).
2. Press [Adjustment/Maintenance] 
[Maintenance]  [Clean Feeder].
3. Load 10 sheets of blank paper in the
feeder  press [Start].
Additional Information
For more information on Automatic
Gradation Adjustment, see e-Manual >
Settings/Registration.
24
The printed paper is warped.
If you print an original filled with
an image or an original with a
high image density, the paper may
become warped. To reduce the
warping, try the following.
■ Use heavy paper:
If you are using thin paper, replace it with
heavy paper with a weight of approximately
20 lb bond (80 g/m2).
196
Q&A
■ Use paper with a low moisture
content:
When printing from the computer, you
can set a password for printing (Secured
Printing). You can prevent another user
from taking the output by mistake or
prevent outputs from being left behind
because the print job cannot be started
until the password is entered on the touch
panel display of the machine. For more
information, see e-Manual > Practical
Workflows.
Troubleshooting
When you remove paper from its packaging,
load it into the paper source immediately.
When there is paper remaining in the
packaging after you have loaded the paper,
store it with the packaging closed properly
to prevent the paper from absorbing
moisture.
Additional Information
Additional Information
For information on loading paper, see
e-Manual > Maintenance.
25
I had printed from the computer,
26
Can I specify the scan settings from
the computer and then store for
the original loaded in the machine?
but I did not find the output. I am
afraid that someone may have
taken it by mistake.
It is possible if you are using
Windows. Install the Network
ScanGear Driver in your computer,
You can check the Print Logs from
and then switch the network scan
the touch panel display of this
function to online.
machine. If the job is listed as ‘OK’
on the Log and you did not find
■ To Install the Driver:
the output, the print job may have
Install using the UFR II User Software CDROM that comes with the machine.
intermixed with another user’s
output.
■ To check:
1. Press
(Status Monitor/Cancel).
2. Press [Copy/Print]  [Log]  press the
drop-down list.
3. Select the job type to display and check
the log.
197
Q&A
■ To Switch the Network Scan
Function to Online:
27
Press [Scanner]  [Online].
Can I make copies or send a
facsimile of different size originals
at the same time?
You can make copies or send a
facsimile of different size originals
at the same time by using the
Different Size Originals mode.
* The Different Size Originals mode enables you to
copy/scan different size originals with the same
widths (11” x 17” and LTR, or LTRR and STMT, etc.)
or different widths (11” x 17” and LGL, or LTR and
STMT, etc.) together.
■ Setting procedure:
1. Press [Copy] or [Fax]  [Options] 
[Different Size Originals].
2. Select the type of different size originals
 press [OK].
Additional Information
For instructions on installing the Network
ScanGear Driver, see the Network ScanGear
User’s Guide on the UFR II User Software
CD-ROM.
Additional Information
For more information, see e-Manual > Copy,
or Fax.
198
Q&A
29
Can I print on the reverse side of
Can I output paper to a different
the preprinted paper?
tray according to the function?
You can use [2nd Side of 2-Sided
You can set the output tray for
Page] for the multi-purpose tray to
each function and set priorities for
print on paper already printed on.
outputting paper.
■ Setting procedure:
1. Load the paper in the multi-purpose tray
with the side to print on face up.
2. Select the paper size  press [Next].
3. Select the paper type  press [2nd Side
of 2-Sided Page]  [OK].
4. Press [OK].
5. Press
(Start).
Troubleshooting
28
* The output trays indicated by Tray A, B, and C
differ according to the optional product attached
to the machine.
■ Setting procedure:
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Common] 
[Paper Output Settings].
3. Press [Output Tray Settings].
4. Set the function and tray priority for Tray
A, B, and C  press [OK].
Additional Information
A paper jam is more likely to occur with
paper already printed on compared to new
paper.
199
Q&A
Additional Information
For more information on setting the output
tray for each function, see e-Manual >
Settings/Registration.
31
How do I print data received via
fax/I-fax on paper specified in
advance?
30
What are the types of paper that I
can use?
You can change the paper
source from [Paper Drawer Auto
Selection On/Off] in
You can load and print on the
(Settings/
Registration).
following paper:
■ Setting procedure:
Paper Drawer 3 and 4
Weight:
14 lb bond to 80 lb cover (52 to 220
g/m2)
Size:
11” x 17”, LGL, LTR, LTRR, STMTR,
EXEC, Custom size (5 1/2” x 7 1/8” to
11 3/4” x 19 1/4” (139.7 mm x 182
mm to 297 mm x 487.7 mm))
Type:
Thin, Plain, Recycled, Color, PrePunched, Bond, Heavy 1, Heavy 2,
Tab, Letterhead
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Common] 
[Paper Feed Settings].
3. Press [Paper Drawer Auto Selection On/
Off]  [Receive/Fax]  set the paper
source you want to use for printing
received data to ‘On’  set the paper
sources you do not want to use to ‘Off’.
4. Press [OK]  [OK].
Paper Drawer (Right/Left)
Weight:
14 lb bond to 80 lb cover (52 to
220 g/m2)
Size:
LTR
Type:
Thin, Plain, Recycled, Color, PrePunched, Bond, Heavy 1, Heavy 2,
Letterhead
Multi-Purpose Tray
Weight:
14 lb bond to 140 lb index (52 to
256 g/m2)
Size:
11” x 17”, LGL, LTR, LTRR, STMTR,
EXEC, Custom size (4” x 5 7/8” to 11
3/4” x 19 1/4” (100 mm x 148 mm to
297 mm x 487.7 mm))
Type:
Thin, Plain, Recycled, Color, PrePunched, Bond, Heavy 1, Heavy
2, Heavy 3, Tracing, Transparency,
Labels, Letterhead
Additional Information
For more information on the available paper
types, see e-Manual > Basic Operations.
200
Additional Information
For more information, see e-Manual >
Settings/Registration.
Q&A
32
33
How can I manage documents that
When a fax fails to be sent, both
failed to be forwarded?
the TX Report and the Fax TX
Report are output. Is there a way to
Troubleshooting
not output the Fax TX Report?
You can specify how to manage
jobs that failed to be forwarded
in [Handle Files with Forwarding
Disable the output function for
Errors] in
the Fax TX Report. Specify the
(Settings/Registration).
following settings.
■ Setting procedure:
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Receive/
Forward]  [Common Settings].
3. Press [Handle Files with Forwarding
Errors]  select how to manage the
forwarding errors  press [OK].
• If you select [Always Print], jobs with
forwarding errors are always printed.
• If you select [Store/Print], jobs with
forwarding errors are stored in Memory
RX Inbox.
• If Fax Memory Lock or I-Fax Memory Lock
is set to ‘Off,’ jobs with forwarding errors
are printed.
• If you select [Off], no jobs with forwarding
errors are printed.
■ Disabling output of the Fax TX
Report:
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Send] 
[Fax Settings].
3. Press [Fax TX Report]  [Off]  [OK].
Additional Information
For more information, see e-Manual >
Settings/Registration.
Additional Information
For more information, see e-Manual >
Settings/Registration.
201
Q&A
Additional Information
34
How do I print the data received
from specific destinations only?
You can set the Store/Print
• If the Fax Memory Lock is being used,
received data is stored in the Memory RX
Inbox without being printed.
• For more information, see e-Manual >
Settings/Registration.
35
Received File mode in Forwarding
Settings to print the data received
What is the model number of the
from specific destinations only.
staple cartridge for the finisher or
the stamp cartridge for the feeder?
■ Printing for Specific
Destinations Only
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Receive/
Forward]  [Common Settings].
3. Press [Forwarding Settings] 
[Register]  specify the destinations in
[Conditions].
4. Set <Store/Print Received File> to ‘On’ 
press [OK]  [Close].
The model numbers of the
consumables for the feeder and
finisher are as follows:
■ Stamp Ink Cartridge-C1
For the feeder
■ Staple-J1
For the Staple Finisher-P1 and Booklet
Finisher-P1
■ Staple Cartridge-D2/Staple
Cartridge-D3
For the Booklet Finisher-P1
Additional Information
■ Forwarding to the Confidential
Fax Inbox for Other
Destinations
1. Press
(Settings/Registration).
2. Press [Function Settings]  [Receive/
Forward]  [Common Settings].
3. Press [Forwarding Settings]  [Forward
w/o Conditions]  specify the
Confidential Fax Inbox as the forwarding
destination.
4. Press [OK]  [Close].
202
For information on replacing the staple
cartridges and stamp cartridges, see
Chapter 3, “Routine Maintenance.”
Q&A
36
■ Feeder
A paper jam has occurred. How do I
solve this problem?
Troubleshooting
The procedure for clearing a paper
jam is displayed on the touch panel
display.
Follow the instructions to clear the
paper jam.
■ Fixing Transport Unit (Inside the
Main Unit)
Additional Information
If the problem is still not resolved, see
Chapter 4, “Troubleshooting.”
203
Q&A
t remove the toner cartridge after the toner replacement cover is opened.
37
38
Numbers, such as #751 and #801
I cannot print from the computer.
are displayed on the touch panel
Did the machine malfunction?
display. What do they mean?
Check the following possible
These are error codes indicating
causes:
that a job or operation did not
complete successfully. They are
displayed on the Details screen
■ Is the network cable
disconnected?
from [Log] on the Status Monitor/
Cancel screen.
Ethernet Cable
Hub
■ Is it possible that there is a
network problem?
Perform the necessary procedures after
referring to the causes and remedies for
the error codes described in e-Manual >
Problem Solving.
■ Is the machine turned ON?
Additional Information
For instructions on using
(Status
Monitor/Cancel), see e-Manual > Status
Monitor/Cancel.
■ Is there a paper jam or a toner
shortage?
■ Did you exceed the maximum
number of prints set by the
Department ID Management?
Additional Information
When network trouble occurs or for
information on Department ID Management
settings, contact your System Manager.
204
Q&A
39
40
It seems as though turning OFF
The touch panel display is
the machine is different from the
completely black.
previous imageRUNNER. I am
Troubleshooting
afraid that this may be a wrong
operation.
The main power has not been
turned ON, or the machine may
have entered the Auto Sleep
For the previous imageRUNNER,
mode to save energy. Follow the
you needed to press and hold the
procedure below.
control panel power switch for
more than three seconds before
the machine entered the Shutdown
mode.
However, for the imageRUNNER
ADVANCE, you just need to open
■ Turning the main power ON
1. Check whether the power plug is firmly
inserted into the outlet.
2. Open the main power switch cover
located on the right side of the machine
and switch the main power switch to the
“I” side to turn the power ON.
the main power switch cover
located on the right side of the
machine, and push the main power
switch toward the “ ” side.
■ Recovering from the Auto Sleep
mode
Press the
Additional Information
For more information, see Before Using This
Machine.
(Energy Saver).
Additional Information
• For more information on the Auto Sleep
mode and Energy Saver mode, see
e-Manual > Basic Operations.
• Follow the procedure below to change the
Auto Sleep Time.
1. Press
(Settings/Registration).
2. Press [Preferences]  [Timer/Energy
Settings]  [Auto Sleep Time].
3. Specify the time  press [OK].
205
Q&A
41
42
I have just sent an important
Can I restrict the number of copies/
document via facsimile. Can I
prints?
check to make sure that it was sent
correctly?
If Department ID Management is
used, you can restrict the copy or
You can check the send job status
print output within groups.
from the Status Monitor/Cancel
screen or receive notification of the
sending result via e-mail.
■ To check from the Status
Monitor/Cancel screen:
1. Press
(Status Monitor/Cancel).
2. Press [Send]  [Log].
■ To receive send result via
e-mail:
1. Press [Fax]  [Options]  [Job Done
Notice].
2. Specify the e-mail address where you
want to receive the result notification.
Additional Information
If the Fax TX Report is set, you can output
and check the Fax TX Report every time.
Also, if the Fax Activity Report is set, you can
output and check Fax Report from the past.
For more information, see e-Manual > Basic
Operations.
206
■ Setting the Department ID
Management and Registering
the Password:
1. Press
(Settings/Registration).
2. Press [Management Settings]  [User
Management]  [Department ID
Management].
3. Press [On]  [Register PIN]  [Register].
4. Enter the Department ID and PIN 
press [OK].
■ Setting the Page Limits:
1. Press
(Settings/Registration).
2. Press [Management Settings]  [User
Management]  [Department ID
Management].
3. Press [On]  [Register PIN]  [Register].
4. Press [Turn Limits On/Off and Set Page
Limits]  specify the page limit settings
 press [OK].
Q&A
Additional Information
To perform this procedure, you must
have administrator privileges. For more
information, see e-Manual > Security.
1. Press
(Settings/Registration).
2. Press [Preferences] [Display Settings]
 [Language/Keyboard Switch On/Off].
3. Press [On]  [OK]  [Language/
Keyboard Switch].
4. Select the language to display  press
[OK].
Troubleshooting
43
■ Setting procedure:
Can I change the language
displayed on the touch panel
display?
You can change the language
displayed from [Language/
Keyboard Switch] in
(Settings/
Registration).
Additional Information
• You can follow the procedure below to
display a shortcut to the language switch
on the Main Menu screen.
1. Press
 [Other Main Menu Settings]
 ‘On’ for <Display [Language/Keyboard
Switch]>.
2. Press [OK].
• For more information, see e-Manual >
Basic Operations.
Displayed Language: English
Displayed Language: Other
207
Q&A
■ Changing the Displayed
Function:
44
Can I change the screen or the
order that the functions are
displayed on the touch panel
1. Press
.
2. Press [Main Menu Button Display
Settings].
3. Select the layout or the order to display
the function key  press [OK].
display when the power is turned
ON?
You can change the default display
that appears after the machine is
turned ON from [Default Screen
after Startup/Restoration] in
(Settings/Registration). You
can also change the order that
the functions are displayed or the
layout from [Main Menu Button
Display Settings] in
.
■ Setting the Default Display That
Appears after the Machine Is
Turned ON:
1. Press
(Settings/Registration).
2. Press [Preferences]  [Display Settings]
 [Default Screen after Startup/
Restoration].
3. Select the settings  press [OK].
208
Additional Information
To perform this procedure, you must
have administrator privileges. For more
information, see e-Manual > Security.
You can also recall the settings that are
previously stored as settings for frequently
used functions from
(Main Menu).
For more information, see e-Manual > Quick
Menu.
Q&A
45
I want to check the IP address for
this machine to run the Remote UI,
but I do not know how to check it.
Additional Information
• To perform this procedure, you must
have administrator privileges. For more
information, see e-Manual > Security.
• If you cannot start the Remote UI, specify
the following settings.
Troubleshooting
1. Press
(Settings/Registration).
2. Press [Management Settings] 
[License/Other]  [Remote UI].
3. Press [On]  [OK].
You can check the IP address from
the touch panel display of this
machine.
■ Checking the IP Address of This
Machine:
IPv4 Address
1. Press
(Settings/Registration).
2. Press [Preferences]  [Network]  [TCP/
IP Settings].
3. Select [IPv4 Settings]  [Use IPv4] 
[On].
4. Press [IP Address Settings].
IPv6 Address
1. Press
(Settings/Registration).
2. Press [Preferences]  [Network]  [TCP/
IP Settings].
3. Select [IPv6 Settings]  [Use IPv6] 
[On].
4. Press [Manual Address Settings].
■ Starting the Remote UI:
Run the Web browser for the computer 
enter ‘http://<IP address of the machine>’ in
the address bar.
209
Q&A
46
Can I change the default settings of
the printer driver?
You can change the print settings
■ Using a Macintosh:
Page Settings:
1. Click [Page Setup] from the [File] menu in
the application software.
2. Select each item as indicated below.
Setting: [Page Attributes]
Printer: The name of your printer
3. Click the <Settings> drop-down list 
[Save As Default]  [OK].
of the printer driver from the
computer you are using.
■ Using Windows:
1. On the [Start] menu, click [Control Panel]
 [Printer].
2. Right-click the printer icon  click
[Printing Preferences]  specify the
printer settings.
3. Click [OK].
Print Settings:
1. Click [Print] from the [File] menu in the
application software.
2. Click the <Printer> drop-down list 
select the name of your printer.
3. Click the <Presets> drop-down list 
[Save As].
4. Specify [Save Preset As]  click [OK].
210
Q&A
5. Click the <Presets> drop-down list 
select the saved preset name  click
[Print].
47
Is there a way to adjust the sound
heard when fax sending/receiving
is complete?
Troubleshooting
You can use
(Volume Settings)
on the control panel to adjust the
volume.
■ Setting procedure:
1. Press
(Volume Settings) on the
control panel.
2. Press
or
to adjust the Alarm
Volume and Monitor Volume  press
[OK].
211
Q&A
48
What is MEAP?
MEAP stands for Multifunctional
Embedded Application Platform
and is a software platform for the
Canon multitasking machines.
You can expand the functions
or customize them by installing
the MEAP application from the
computer to the multitasking
machine.
■ Workflow Composer
The Workflow Composer is an application
that increases the efficiency of operations
that use multiple functions of the machine.
By creating and registering combinations
of functions that are frequently used on the
machine, you can repeatedly reuse the same
combination of functions.
SMS
Application
Install
Machine
Additional Information
For more information, see e-Manual > MEAP.
212
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON U.S.A., INC.
One Canon Plaza, Lake Success, NY 11042, U.S.A.
CANON CANADA INC.
6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada
CANON EUROPA N.V.
Bovenkerkerweg 59-61 1185 XB Amstelveen, The Netherlands
(See http://www.canon-europe.com/ for details on your regional dealer)
CANON LATIN AMERICA, INC.
703 Waterford Way Suite 400 Miami, Florida 33126 U.S.A.
CANON AUSTRALIA PTY. LTD
1 Thomas Holt Drive, North Ryde, Sydney, N.S.W. 2113, Australia
CANON CHINA CO., LTD
15F Jinbao Building No.89 Jinbao Street, Dongcheng District, Beijing 100005, China
CANON SINGAPORE PTE. LTD.
1 HarbourFront Avenue #04-01 Keppel Bay Tower, Singapore 098632
CANON HONGKONG CO., LTD
19/F., The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kowloon, Hong Kong
FT5-4702 (000)
XXXXXXXXXX
© CANON INC. 2012
PRINTED IN CHINA