Canon PIXMA MX7600 Instruction Guide

1
Easy Setup Instructions for Preparing the Machine
Office All-In-One
• Please confirm the included items against the illustration printed on the lid of the packing box.
• A USB cable is necessary to connect the machine with your computer.
Unpack the Machine
1 Prepare the Machine
Important
When cleaning the exterior of the machine, use a soft cloth to wipe it gently. For details, refer to “Cleaning Your Machine” in the Quick Start Guide.
2 Install the Print Head
aLocate the machine on a level place.
dPlug the power cord in the back of the machine and connect the
Caution
Since this machine weights approximately 36.6 lbs. (16.6 kg), it is recommended
that two people move or relocate the machine.
other end to the wall outlet.
aFirmly raise the Print Head Lock Lever until it stops. The Print
Head Lock Lever may feel heavy.
ePush the Print Head to hold it in place, and lower the Print Head
Lock Lever.
Document Cover
Note
Be sure to remove the tapes and protective material before you turn on the machine.
When lifting the machine with two people
When lifting the machine alone
Important
• Make sure that the Document Cover is closed.
• Do NOT connect the USB cable at this stage.
ePress the ON/OFF button to turn on the machine.
Place your fingers in the indented
portions on the bottom of the machine.
Do not hold this part!
The machine will initialize. Wait until the COPY button stops flashing and
remains lit green.
Important
• Make sure that the machine is turned on and the COPY button lights green.
• Make sure that the Print Head Holder has moved to the center.
bRemove the Print Head from its package.
bRemove the protective material in the ADF (Auto Document
Do not touch!
Feeder).
Protective Material
Proceed to the step 3 on the reverse side.
fPress the { or } button on the Operation Panel to select the
language for the LCD, then press the OK button.
Note
• The tape or the protective material position is subject to change.
Installing cleaning sheets
• Cleaning sheets can be stored in the Cleaning Sheet Holder. For details on installing
cleaning sheets, refer to “Cleaning the Inside of the Machine (Sheet Cleaning)” in the
Quick Start Guide.
(1) Press the { or }
button to select the
language.
(2) Press the OK button.
Caution
There may be some transparent or light blue ink on the inside of the bag the print
head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items.
cRemove the orange protective cap from the Print Head and
discard it.
Electrical Contacts
Important
If an unintended language is displayed on the LCD, press the Back button on the
Operation Panel to return to the Language selection screen.
This machine comes with
five cleaning sheets.
cConnect the telephone line and any necessary external device.
You can connect an external device (telephone or answering machine) if
necessary.
Remove the Telephone connector cap to connect the external device.
Once the message “Install the print head and set the ink tank.” appears, go
to g.
gLift the Scanning Unit (Printer Cover) until it locks into place.
The Paper Output Tray will open automatically and the Print
Head Holder moves to the center. Then open the Output Tray
Extension.
Print Head Nozzles
If the Paper Output Tray does not open automatically, press the Open button to
open it.
Telephone connector cap
Protective Cap
Important
Do not touch the print head nozzles or the electrical contacts.
Connect the telephone line cable to the wall jack.
dInsert the Print Head.
Connect external devices as follows:
External Device Jack
Telephone Line Jack
Telephone or answering machine
Telephone or
answering machine
Telephone
line
Machine
Built-in computer modem and telephone
Telephone
line
Important
If the Scanning Unit (Printer Cover) is left open for more than 10 minutes, the
Print Head Holder moves to the right. Close and reopen the Scanning Unit (Printer
Cover) to return the Holder to the center.
LINE TEL
Computer
Machine
Important
Be sure to use the bundled telephone line cable.
Telephone
Caution
For your safety, always firmly grip the areas illustrated when lifting the Scanning
Unit (Printer Cover).
Important
If the Document Cover is opened, you cannot open the Scanning Unit (Printer
Cover). Be sure to open the Scanning Unit (Printer Cover) with the Document
Cover closed.
Do not touch!
3 Install the Ink Tanks
Note
For the ink tanks compatible with this machine, refer to the back cover of the Quick
Start Guide.
4 Install the Clear Ink Tank
5 Align the Print Head
aRemove the orange tape in the direction of the arrow to peel
aClose the Paper Output Tray and pull out the Cassette from the
off the protective film from the clear ink tank.
machine.
To use a fax, you need to set the telephone line type setting properly
on the machine.
Do not touch!
aRemove and discard the orange protective cap located on the
For fax users
bottom of the ink tank.
If you are unsure of your telephone line type, contact your telephone
company.
Protective Cap
Ink Port
Select the receive mode according to your needs.
• When you receive mainly faxes and sometimes voice calls:
→ FAX priority mode
Electrical Contacts
bPush the tab and open the Clear Ink Tank Locking Cover.
Do not press!
Important
• Do not touch the electrical contacts.
• Do not touch the ink port.
bLoad four sheets of plain paper in the Cassette with the
printing side facing DOWN and the leading edge to the
far side, align the paper stack against the right side of the
Cassette, then slide the Paper Guides to fit to the loaded paper
stack.
• When you have a dedicated telephone line for fax use only:
→ FAX only mode
• When you receive mainly voice calls and sometimes faxes:
→ TEL priority mode
• When you subscribe to a ring pattern detection service provided by
your telephone company, and you want to receive a fax only if the
machine detects the pattern for fax:
bInsert the ink tank into the right-hand slot and press the
mark on the ink tank until it clicks into place.
→ DRPD
For details on how to confirm and change the settings, refer to the
Quick Start Guide.
Paper Guide
cBe sure that the clear ink tank is properly aligned when
inserting.
cInsert the Cassette into the machine.
Push the Cassette all the way into the machine.
For USB connection and software installation, proceed to “2
Easy Setup Instructions for USB Connection and Software
Installation.”
dMake sure that Yes is selected in the message requesting
dClose and press the round, indented portion on the Clear Ink
For wired LAN connection, refer to the Network Setup Guide.
head alignment, then press the OK button.
Tank Locking Cover until it snaps firmly into place, locking the
ink tank.
cMake sure the ink lamp lights red.
Refer to the color guide on
the Print Head Lock Lever.
Note
Print Head alignment takes about 9 minutes to complete. Do not start another
operation until the machine has stopped making operating noises.
eClose the Scanning Unit (Printer Cover).
The pattern is printed. And Print Head is aligned automatically.
OK
Caution
For your safety, always firmly grip the areas illustrated when closing the Scanning Unit (Printer Cover).
Important
The machine starts the preparatory operation. It takes about 2 minutes. Do not
start another operation until the machine has stopped making operating noises.
Note
If the Alarm lamp lights and an error message is displayed on the LCD, refer to “An
Error Message Is Displayed on the LCD” in the Quick Start Guide.
Note
• The pattern is printed in black and blue.
• When Automatic Print Head Alignment cannot be executed correctly, the message
“Auto head align has failed.” is displayed on the LCD. Refer to “An Error Message
Is Displayed on the LCD” in the Quick Start Guide.
Hardware setup and Print Head alignment are complete.
Part no. QT5-0072-V02 © 2008 Canon Inc.
XXXXXXXX
Printed in THAILAND