advertisement
▼
Scroll to page 2
of 35
Dear Customer, You have just acquired a DE DIETRICH dishwasher and we would like to thank you. Our research teams have created this new generation of appliances for you. Their quality, design, features and technological advances make them exceptional products, and reveal our unique know-how. Your new DE DIETRICH dishwasher will blend harmoniously into your kitchen and will perfectly combine washing and drying performance and ease of use. We wanted to offer you a product of excellence. In the DE DIETRICH product range, you will also find a wide choice of hobs, ovens, microwaves, hoods, cookers, fridges, freezers, that you can coordinate with your new DE DIETRICH dishwasher. Visit our website www.dedietrich-electromenager.com, where you will find our latest innovations as well as useful and complementary information. DE DIETRICH Setting New Values As part of our commitment to constantly improving our products, we reserve the right to make changes to them based on technical advances to their technical and functional features and appearance. Warning : Before installing and using your appliance, please carefully read this Guide to Installation and Use, which will allow you to quickly familiarise yourself with its operation. 34 EN CONTENTS 1/ FOR THE USER’S ATTENTION • Safety instructions ______________________________________ • Protection of the environment______________________________ • Economical, environmentally friendly washing ________________ 2/ DESCRIPTION OF YOUR APPLIANCE • General presentation of the dishwasher ____________________ • Presentation of the control panel __________________________ 3/ INFORMATION ______________________________________________ 4/ WHAT TO DO BEFORE FIRST USING THE MACHINE • Measure the water hardness and select the type of detergent __ • Hardness table__________________________________________ 5/ DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER • For traditional products __________________________________ • For multi-purpose products ________________________________ 6/ LOADING OF REGENERATING SALT __________________________ 7/ LOADING OF RINSING PRODUCT ____________________________ 8/ YOUR DISHWASHER’S EQUIPMENT • The lower basket ________________________________________ • The upper basket ________________________________________ • The cutlery basket ______________________________________ 9/ SETTING THE PARAMETERS__________________________________ 10/ WASHING PROGRAMMES TABLE ____________________________ 11/ PROGRAMMING __________________________________________ 12/ YOUR DISHWASHER’S SAFETY SYSTEMS ____________________ 13/ CLEANING YOUR APPLIANCE • Cleaning the waste filters ________________________________ 14/ IF OPERATING ABNORMALITIES OCCUR ______________________ • Changing the bulb ______________________________________ 15/ AFTER-SALES SERVICE ____________________________________ 16/ INDICATIONS FOR THE TESTING LABORATORIES ______________ 35 36 37 37 38 39 40 41 41 42 43 44 45 46 47 48 49 50 52 54 55 57 62 63 64 EN 1/ FOR THE USER’S ATTENTION • Children’s safety Important : — This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely. — This appliance must only be used by adults. Ensure that children do not touch it and do not use it as a toy. Ensure that they do not operate the appliance’s controls. — Keep young children away from the appliance when it is operating. — Detergents contain irritant and abrasive substances. These products can have caustic effects on the eyes, the mouth or the throat. They can be extremely dangerous if ingested. Avoid any contact with the skin and the eyes. Ensure that the appliance’s detergent container is empty at the end of the washing cycle. — Place detergents out of children’s reach and do not put any detergent in the machine until just before you start the washing programme. — The water in your dishwasher is not drinking water; this is why children must not go near the appliance when its door is open. — Do not let your children play or sit on the door when it is open. — Once you have unpacked your appliance, place the packaging out of children’s reach. — Keep all the packaging materials (e.g. plastic bags, polystyrene, etc.) out of children’s reach because they can be dangerous for children (ie. risk of suffocation). Keep this user’s manual with your appliance. If the appliance is sold or transferred to someone else, ensure that the manual is with it. Please take note of these instructions before installing and using your appliance. They have been drawn up for your own and other people’s safety. • SAFETY INSTRUCTIONS • Installation — When you receive your appliance, unpack it or have it unpacked immediately. Check that it has not suffered any damage during transport. Express any reservations in writing on the delivery note, of which you keep a copy. Never connect up a damaged machine. If your appliance is damaged, please contact your dealer. — Before proceeding to connect up your machine, please refer to the instructions in your Installation Guide. — Your dishwasher must be kept disconnected from the mains supply throughout the whole of the installation process. — The electrical connection details on your appliance’s description plate must comply with those for the mains supply. — The socket must still be accessible once your appliance has been installed. — Do not alter or attempt to alter the appliance’s characteristics. This could put you at risk. — If your installation has to be altered, only entrust the electrical and plumbing work to a qualified electrician or plumber respectively. — Your appliance is designed for normal domestic use. Do not use it for industrial or commercial purposes or for any other purpose than that for which it has been designed. — The dishwasher’s walls must not be pierced under any circumstances. • Use — This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. — When machine is running, do not open door. This may provoke steam leakage or splattering of water. 36 EN 1/ FOR THE USER’S ATTENTION — Only use products specially designed for your dishwasher (water softening salt, detergent and rinsing products). — As far as possible, avoid opening the dishwasher’s door when it is operating, and in particular during the heating phases, because scalding steam may escape or you may be splashed with hot water. The machine is fitted with a safety system that immediately blocks the dishwasher’s operation if the door is opened. — Never use chemical solvents in your appliance because these could cause an explosion. — Always close your appliance’s door after loading or removing your items. — Do not lean or sit on your appliance’s door when it is open. — You are strongly advised to disconnect the machine after use and turn off the water supply. — Unplug your machine before carrying out any technical work on it. — Avoid placing your machine immediately next to a cooking or heating appliance to prevent any risk of heat damage; — Do not place any items in your machine, which are not certified as dishwasher safe. — If you have removed an item before the end of the washing programme, it is important to rinse it carefully to remove any residual washing products. — If your appliance breaks down, never attempt to repair it yourself. Any repairs made by non-qualified personnel can cause significant damage or lack of control. — The machine complies with applicable safety regulations. Any repairs should be carried out by qualified technicians. Repairs or changes that do not conform may be dangerous for the users. In case of replacement, only use original parts. — If the machine malfunctions due to other causes than those mentioned in this booklet, disconnect the machine (remove the plug) or break the circuit concerned and contact Kleenmaid’s after-sales service. • ENVIRONMENTAL PROTECTION This appliance’s packaging material is recyclable. Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose. Your appliance also contains a great amount of recyclable material. It is marked with this label to indicate that in countries that are a members of the European Union the used appliances should not be mixed with other waste. This way, the appliance recycling organised by your manufacturer will be done under the best possible conditions, in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home. We thank you doing your part to protect the environment. • ECONOMICAL, ENVIRONMENTALLY FRIENDLY WASHING — Remove any food residue from your crockery (bones, pips, etc.) — Do not pre-wash your items by hand (useless waste of water). — Utilise your dishwasher’s capabilities to the full for an economical, environmentally friendly wash. — Always select a washing programme suitable for the crockery type and how dirty they are. — Avoid overdosing with detergent, regenerating salt and rinsing liquid. Follow the recommendations in this guide (pages 43-44-45) and the instructions on the product packs. — Ensure that the water softener is correctly set (see pages 42-43). 37 EN 2/ DESCRIPTION OF YOUR APPLIANCE • GENERAL PRESENTATION OF THE DISHWASHER A B C D E F G H I Fig. 01 A Upper basket F Waste filter B Washing products dispenser G Main filter C Anti-blocking gauge wire H Rinsing product dispenser D Lower sprinkler arm I Description plate (After-Sales Ref) E Regenerating salt tank Advice: This user’s guide is applicable to several models. There may be some slight differences in the details and the equipment between your appliance and the descriptions provided here. 38 EN 2/ DESCRIPTION OF YOUR APPLIANCE • PRESENTATION OF THE CONTROL PANEL Fig. 02 C A A On/Off: Press this button to start your dishwasher. B D E F G F Delaying the end of a programme: Press one of the buttons or the other to select the time for the programme to end. B Choosing a programme: briefly press one button or the other in succession to select your programme. G Start/Cancel: Briefly press this button to start your programme. If you make an error, to cancel a selection or cancel a programme while it is running, hold down this button for 3 seconds. C : Intelligent Control System press this button to select the Automatic programme. The indicator lights: Salt: D Set : • A long press: Access to the Settings menus: - Set the current time, - Set the water softener, - Activate or deactivate the “Regenerating Salt” and/or “Rinsing Product” lights, or the “AUTO 4/1” function (depending on the water softener setting on the following pages). - Beep at end of programme, - Set screen brightness. When lit, it indicates lack of regenerating salt Rinsing liquid: When lit, it indicates lack of rinsing product Multipurpose products: lit; shows you that the “AUTO 4/1” feature is turned on and that the programmes are now automatically adjusted if a multi-function tablet is used. E The screen shows you the current time, the finishing time, the remaining time for the programme and the parameter settings. Programme progress : This shows you the programme’s progress. Advice: A short audible signal (beep) confirm the button’s selection, except for the “On/Off” button. 39 EN 3/ INFORMATION Important: Important: Never use normal washing-up liquid. To obtain impeccable washing and drying results from your dishwasher without any marks, you must set it carefully using the water softening system, which utilises regenerating salt. For ease of use and in certain water hardness conditions only (< 25°F), multi-purpose products can make the use of regenerating salt and rinsing liquid unnecessary. • “Two-in-one” tablets contain detergents and rinsing liquid or an agent serving the function of the salt. • “Three-in-one” tablets contain detergents and rinsing liquid as well as an agent serving the function of the salt. • “Four-in-one” tablets also contain additives that prevent wear on poor quality glasses or the risk of stainless items corroding. As rainwater infiltrates into the ground it picks up mineral salts; some minerals are found in solid form and are commonly called ‘lime’. This reduces the detergent’s washing performance and leaves white marks on the crockery. The more lime there is in the water, the ‘harder’ the water is. - Use the most suitable washing products for the hardness of your town’s water supply. - There are several types of products: Important: Follow the instructions in the user’s manual and the recommendations on the multi-purpose detergent’s pack. NB: If in any doubt, please contact the detergent’s manufacturer if the items are very wet at the end of the programme or if chalky deposits appear. For an impeccable clean, opt for using traditional products together: ① Washing product for a perfect clean (standard powder, liquid or tablets). ② Regenerating salt for your dishwasher’s water softener to work correctly. ③ Rinsing liquid to assist drying and eli- minate drip marks. 40 EN 4/ WHAT TO DO BEFORE FIRST USING THE MACHINE • MEASURE THE WATER HARDNESS AND SELECT THE TYPE OF DETERGENT: TRADITIONAL OR MULTI-PURPOSE In one simple action, you can test the your water’s lime content using the testing strip supplied with your dishwasher. Alternatively, contact your local water utility to ascertain your water’s hardness. — Let the water run from the tap for a few moments. — Fill a glass with water. — Take the test strip from its holder and immerse it for 3 seconds. — Wait 1 minute, shake it and look at the colours to ascertain your water’s hardness. • HARDNESS TABLE Test strip Hardness Water Water softening and use of salt > 70°F 10-18°F 18-25°F 25-40°F 40-55°F 55-70°F Very hard Slightly hard Slightly hard Hard Hard Hard Essential if Essential if Optional using traditional using traditional Mandatory Mandatory Mandatory Mandatory products products 0-10°F Soft Possible use of traditional products ➊ ➊ or ➋ or + + Use only of traditional products ➊ R or Multi-purpose + + R ➋ ➊ Traditional products: P : Powder detergent or L : Liquid detergent + S : Regenerating Salt + R : Rinsing product Multi-purpose tablets ➋ Multi-purpose products: 41 EN 5/ DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER • FOR TRADITIONAL PRODUCTS • Your machine must be specially adjusted to use traditional products. • Proceed as follows to adjust the water softener on the control panel: — This feature is adjusted using the “SET” ; button; hold down this button to access the menu. Then press twice to set the softener level. — The softener level is then shown on the screen from H0 to H6 . The default level is H4 . — To change the level from H0 to H6 , depending on the water hardness, press either arrow button several times the screen displays the level you have set. — The setting is validated automatically after 10 seconds if the “SET” button in not pressed again. — Pressing “SET” enables you to validate the setting and move on to the next parameter. Testing strip Hardness 0-10°F Traditional product H0 10-18°F 25-40°F 18-25°F HI H2 H3 40-55°F 55-70°F H4 H5 > 70°F H6 Factory setting : H4 Important: It is very important to set the water softener correctly. - If the setting is too low, there is the risk of chalky marks appearing. - if the setting is too high, there is the risk of causing clouding of the glasses. If you relocate, adjust the water softener setting as required. • Traditional tablets Non-multipurpose tablets should be placed in the external compartment (Fig 04) or, for optimum performance, pull out the dispenser drawer and lay the tablet inside (Fig 05). • Powders or liquids (Fig 13) Fill at least up to the minimum mark for slightly dirty crockery and to the maximum mark for dirty crockery. If the crockery is very dirty and for programmes with a pre-wash we recommend that you add 5g of detergent (a dessert spoonful) into your dishwasher’s tub in accordance with the programmes table. Important: Keep these products out of children’s reach and away from dampness. Only use products specially designed for dishwashers. Fig. 03 Fig. 04 Fig. 05 42 EN 5/ DETERGENT PRODUCTS AND ADJUSTING THE WATER SOFTENER • FOR MULTI-PURPOSE PRODUCTS (Water hardness < at 25°F) • Your appliance automatically adapts to using multipurpose products when the water hardness is < 25°F. • Proceed to set the water softener — This feature is adjusted using the “SET” ; button; hold down this button to access the menu. Then press twice to set the softener level. — The softener level is then shown on the screen from H0 to H6 . The default level is H4 . — In order to use multi-function tablets, you need to adjust the setting. To do this, press either arrow button several times until you have selected H0 or H I or H2 depending on the water hardness. • Proceed to set the “ ” function (optional) — Hold down the “SET” button until the “AUTO 4/1” light flashes, then press one or other of the selection buttons . — : deactivates the “AUTO 4/1” option. : corresponds to activation of the “AUTO 4/1” function with the setting for “Sparkling Clean”. — . This enables you to prioritise a brilliant finish for your crockery. — : corresponds to activation of the “AUTO 4/1” function with the setting for “Extra Dry”.. “Extra dry” enhances the drying results if performance is reduced. — The setting is validated automatically after 10 seconds if the “SET” button in not pressed again. — The “AUTO 4/1” light then illuminates permanently if this option has been selected. Testing strip Hardness “Rinsing” light lit 0-10°F 10-18°F 18-25°F Multi-purpose products Function Deactivated H0 OFF HI OFF H2 OFF Multi-purpose products Sparkling Clean H0 OH HI OH H2 OH Multi-purpose products Extra Dry H0 OH HI OH H2 OH “Drying” light lit “multi-purpose” light flashing NB: You can deactivate the “Salt” and “Rinsing” product lights if you are using multi-purpose products; this is done by using the “SET” button (page 49) • Loading the multi-purpose tablet dispenser To assist in loading the detergent, the distributor is situated on the front of the upper basket. It is compatible with all the products recommended for dishwashers. • Place the tablet in the external compartment (Fig 04 on previous page) or, for optimum results, pull out the distributor’s drawer and lay the tablet inside (Fig 05 on previous page). - Close the dispenser. 43 EN 6/ LOADING OF REGENERATING SALT • Loading of regenerating salt (Fig 06) Filling with salt is essential for providing a good wash without marks. It regenerates the resins that soften the water, by removing its lime content (unless the mains water supply is soft enough). Refer to “Setting the water softener”. A Important : SSEalt L Only use special dishwasher regenerating salt. Do not use table salt or any type of cooking salt, this could damage your appliance’s water softener. A Unscrew and remove the stopper on the salt tank. B B Fill the tank with regenerating salt specially designed for dishwashers. er wEaAtU C Use the funnel supplied with your dishwasher. The first time, top up with water up to the rim of the tank. • Regenerating salt indicator: C This illuminates when salt must be added. After the tank has been filled with regenerating salt, the indicator light may remain lit until the salt has dissolved sufficiently, usually after one cycle (of if the tank has not been filled completely; for example, when first putting the machine into service using the sample). This can be deactivated as indicated in the paragraph “For multi-purpose products” setting table. Fig. 06 Important If the salt overflows when filling the tank, to avoid oxidization of the tub it is advisable to remove the salt crystals or to run a Prewash programme (or Rapid programme depending on the model). 44 EN 7/ LOADING OF RINSING PRODUCT • Loading of rinsing product (Fig. 07) Important : Only use a rinsing product designed for dishwashers. The rinsing product ensures your items shine and are well dried. A A B When first putting the machine into service, fill the tank until the level is flush with the top of the adjustment lever. Pour in at least all the rinsing product provided. The tank contains 120 ml (approximately one glass) The original setting is in the centre (middle position: reference mark 2). If you encounter marks or poor drying after a few cycles, you can adjust the setting using the adjustment lever (fig 07 C ; Reference mark 3 will increase the setting). - Close the tank lightly 3 12 B • Rinsing liquid indicator light: This illuminates when rinsing product is required. It can be deactivated as shown in the paragraph “For multi-purpose products” setting table. 3 12 C Important : If any of the product overflows during filling, sponge up the excess to avoid producing foam. Fig. 07 45 Adjustment lever EN 8/ YOUR DISHWASHER’S EQUIPMENT Very important Items not suitable for washing in a dishwasher: - Wooden cutting boards - Stainless steel utensils or plastic utensils that are not heat-resistant - Copper or pewter items - Glued crockery and cutlery - Cutlery with wooden, horn or mother-of-pearl handles - Antique or hand-painted porcelain When purchasing crockery, glasses or cutlery, ensure that it is dishwasher-safe • THE LOWER BASKET Arrange your items so that the water can circulate freely and spray over all the utensils. Place large diameter dishes and pans at the sides. Do not intersperse, jam together or superimpose flat plates and concave dishes (Fig. 08). The flexible racking spikes makes it easier to arrange your large dishes (Fig. 09). Advice: When you re-insert the lower basket, ensure that nothing catches on the oversize plate barrier to avoid blocking the rotating spray arm. Fig. 08 Unloading your items Empty the lower basket to avoid drips from the upper basket falling onto the lower basket. Fig. 09 46 EN 8/ YOUR DISHWASHER’S EQUIPMENT • THE UPPER BASKET This basket is particularly designed to take glasses, cups, ramekins, small salad bowls, bowls and saucers. Arrange your items methodically to save on space (arranging glasses, cups or bowls together). You can also arrange cups, ladles, etc. on the folding cup racks (Fig. 10) Advice: Position the cavities of glasses, cups or bowls facing downwards. Cutlery basket Fig. 10 • Adjusting the height of the upper basket For large dishes to be loaded in the lower basket, the upper basket must be set the to high position. This can be done with the basket fully loaded (Fig. 11) ① Setting in HIGH POSITION: Gently raise your basket on each side until it engages. Fig. 11 ② Setting in LOW POSITION: Raise your basket completely on both sides to unlock it and then lower it to the low position. Important : Check that the two slides are set to the same height and the basket is horizontal. 47 EN 8/ YOUR DISHWASHER’S EQUIPMENT • THE CUTLERY BASKET The cutlery basket slides to allow flexible loading. It can be placed anywhere in the lower basket. You can therefore make a variety of loads depending on the items (Fig. 12). If your cutlery items or your dishes are too large, alter the height setting for the upper basket. Fig. 12 Movable grills are available for if you wish to load your cutlery in an orderly manner (Fig. 13). For optimum washing and drying, use these separation grills partially or totally. Point the handles on the cutlery downwards. Important : Fig. 13 For safety reasons, we recommend that you place knives with pointed ends with the point facing downwards in the cutlery basket (to avoid the risk of an accident). Long-bladed knives and other sharp kitchen utensils must be placed flat in the upper basket. Avoid washing cutlery with horn handles in your dishwasher. Separate silverware from other metals using the separation grill. 48 EN 9/ SETTING THE PARAMETERS • SETTINGS POSSIBLE USING THE “SET” AND SELECTION BUTTONS: • 1 long press on the “SET” button and then a short press enables you to move on to the following parameters. Set the parameters by pressing one of the programme selection buttons or the other. Move on to the next parameter by pressing “SET”. 1 long press Briefly press the “SET” button once and then press one or other of the selection buttons Display > Setting the clock (hour) To do this, hold down the “SET” button. When the time starts to flash, press one of the selection buttons or the other until you reach the desired time. Press SET to move on to the next parameter. > Setting the clock (minutes) Proceed in the same way as above; press one of the selection buttons or the other to set the minutes. > Setting the water softener Set to the level corresponding to the hardness of your water: H0 to H6. > Product use You can cancel display of the relevant indicators, depending on the products used: - Salt Set to OFF if you do not use salt or f you are using multi-purpose tablets. - Rinsing product Set to OFF if you do not use a rinsing product or if you are using multi-purpose tablets. or > Multipurpose tablets and the “AUTO 4/1” function - For optimum product performance (depending on the water softener setting table on page 43), set: to deactivate the “AUTO 4/1” function. to activate the “AUTO 4/1” “Extra Dry” function (default selection) to activate the “AUTO 4/1” “Sparkling Clean” function. > Beep at the end of the programme On to activate the function; OFF if you do not wish not to hear the beep at the end of the program. > Screen brightness Set the screen brightness to suit yourself from Lu1 minimum to Lu5 maximum. Advice: The setting is confirmed automatically when you move on to the next parameter or if the “Set” button is not pressed again within the next 10 seconds. 49 EN 10/ WASHING PROGRAMMES • PROGRAMMES TABLE ITEM TYPE (porcelain, pans, cut lery, glasses) FOOD RESIDUE: Quantity, type and amount Resistant Mixed Mixed Very dirty Normally dirty Normally dirty A large amount of dried-on residue, baked-on stains, grease, residue from frying, cooked cheese, sauce, etc. A normal amount of dried-on and greasy residue on everyday items. Faster, but consumes more energy. A normal amount of dried-on, adhering residue on everyday items. Normal PROGRAMMES PROGRAMME SEQUENCE As an indication only: Duration in min Water (L) Energy (Kwh) Hot pre-wash Pre-wash Pre-wash Washing at 70°C Washing at 65°C Washing at 55°C Rinse Rinse Rinse Hot rinse Hot rinse Hot rinse Air Drying Air Drying Air Drying 130’ 17 1,7 90’ 17 1,5 130’ 15 1,3 These values refer to normal conditions of use with separate products (detergent, salt, rinsing product). They may vary according to the load, the temperature, if you use combined washing products, the water hardness and the supply voltage. 50 EN 10/ WASHING PROGRAMMES Mixed Glassware Mixed Mixed Normally dirty For delicate glasses and dishware. This Crystal + feature maintains the shine of your glasses longer by automatically adjusting the optimum softener level depending on the water hardness. Very short 30minute wash specially designed for a small amount of daily items with a limited amount of non-greasy residue, not dried on. Automatically detects the amount of washing up and the level of soiling. Normal amount of dried on residue on everyday items. Faster, but consumes more energy. Recommanded for normally soiled load, less consuming in energy. Fragile Rapid Pre-wash Washing at 50°C Washing at 45°C Washing at 45°C Washing at 55/65°C Rinse Rinse Rinse Rinse Hot rinse Hot rinse Hot rinse Hot rinse Air Drying Air Drying Natural drying Air Drying 30’ 11 0,8 90’ - 110’ 17 - 19 1,3 - 1,5 145’ 12 1,05 85’ 14 0,8 51 EN 11/ PROGRAMMING Fig. 02 C A B D Advice: E F G Consult the Programmes table on the preceding pages to determine the programme you need for the type of items, the quantity and the amount of food residue. • Starting the appliance On/Off” button A to switch the Press the “O machine on. • Starting a programme immediately Select your programme by pressing one of the selection buttons B . — The Auto programme can be accessed by pressing the “ICS” button C . — The fbutton scrolls the programmes to the left (if the “BOOST” programme is selected, pressing this button causes the “Rapid ” programme to be selected). — The button scrolls the programmes to the right (if the “Rapid ” programme is selected, pressing this button causes the “BOOST” programme to be selected). — When a programme is selected, the relevant indicator light illuminates. The screens shows the envisaged time that the programme will end. Press “Start/C” G ; the programme starts and the screen shows the amount of time remaining for the programme. A short audible signal (beep) confirm the button’s selection, except for the “On/Off” button. 52 Finishing time Programme time remaining, progress End of programme EN 11/ PROGRAMMING • Delaying the end of a Waiting for delayed start programme F Programme the finishing time, in quarter of an hour stages, by pressing the + or – buttons until you reach the desired time. Programme time remaining, progress Confirm by pressing “Start” G . The screen counts down hour by hour until the programme starts. End of programme • Cancelling a programme Hold down the “Start / Cancel” G button for a few seconds. • Stopping the appliance When the programme has finished, press the “On/Off” button A . • Setting the audible signal Beep activated The setting enables you to activate or de-activate the beep at the end of the programme. — Access the setting holding down the “SET” button D until you hear a double signal (long beep). Keep on pressing “Set” successively until you have access to the parameter: Beep de-activated The setting is confirmed automatically after 10 seconds or by pressing “SET” (switching to the next parameter “Screen brightness”). 53 EN 12/ YOUR DISHWASHER’S SAFETY SYSTEMS • SAFETY SYSTEMS • Door poorly closed After confirming the programme (“Start” button), your dishwasher issues three short high-pitched beeps to indicate that the door is not closed and the light for the selected programme flashes. • Programme access lock Throughout the period the programme is running, or the full duration of the programme, the programme selector and the buttons are automatically protected from any kind of manipulation. This unlocks automatically at the end of the programme or when the programme is cancelled by holding down the “Start” button for 3 seconds. • Advice on cleaning the filters Approximately every month, your dishwasher advises you to proceed to service the filters (see Section “Cleaning the waste filters” - Fig. 14-15). • Anti-overflow system This system activates the drain pump automatically if the water in the tank reaches an abnormal level. • Anti-leak protection system This system cuts off the water supply if a leak is detected under the appliance. • Total safety This supply pipe is fitted with a device to cut off the water supply directly at the tap if there is a leak. • Alarm light For programme errors or incidents (please refer to Section 14 "If an operating abnormality occurs"). NB: To unlock, hold down the Start / Cancel button for three seconds. 54 EN 13/ CLEANING YOUR APPLIANCE • CLEANING THE WASTE FILTERS ➀ The filtration system consists of several elements: A - The waste filter B - The large main filter B A C - The micro filter ➁ The filters are located in the centre of the tub and must be washed regularly to obtain optimum washing results. Actions : ➀ Before removing the filters, remove any waste on the large main filter B with a sponge so that the waste does not block the sprinkler arms. Rotate the spray arm as shown in the drawing. (Fig. 14) A ③ ➁ Loosen the waste filter a quarter of a turn and then remove it A ③ Remove the main filter B ④ Remove the micro filter C B C ④ C ⑤ Carefully clean filters A , B and C under running water (Fig. 15) Fig. 14 ⑤ Re-installation: Proceed in reverse order, inserting filters C and B and then A A Important : Fig. 15 Remember to lock the waste filter A in place by pushing it in fully and turning it a quarter turn. 55 B C EN 13/ CLEANING YOUR APPLIANCE • Periodically Every 3 or 4 months, in order to remove any deposits, run a special maintenance programme, without any items in the machine, using a special dishwasher cleaning product. Important : Keep this product out of children’s reach. • If not using your dishwasher for a prolonged period: Clean your dishwasher completely and then unplug it from the electricity supply and close the water tap. Protect your machine from potential frost. Advice : Do not use abrasive powders, metal sponges and alcohol-based or thinner-based products. Use a cloth or a sponge. If you are moving house, run a soaking programme first of all, in order to avoid any water escaping. 56 EN 14/ IF OPERATING ABNORMALITIES OCCUR • SUMMARY OF THE FAULTS Flashing LED(s) for models without a display Flashing LED(s) d01 : water supply fault (tap) d07 : overflow / anti-leak fault d02 : draining fault d08 : sprinkling distribution fault d03 : heating fault d11 : pressure sensor fault d04 : temperature fault d12 : filling fault (water inlet detection system) d05 : fault – motor under load d13 : overheating fault d06 : fault - motor overload d14 : pump filling fault or insufficient flow from the water tap. • BEFORE CALLING FOR SERVICE Problem Possible Causes What to do? The door falls heavily when - Door springs not tensioned - Tighten the two tensioning opened (integratable model) enough to compensate for the screws accessible in the botweight of the panel. tom section above the front feet. The door does not stay horizontal - Door springs tensioned too - Loosen the two tensioning when open or returns too quickly much. screws accessible in the bot(integratable model) tom section above the front feet. - Fit a temporary wooden panel - No wooden panel. on the appliance and adjust the springs. The door catches when closing - Appliance not stable - Door not centred on the tub - Adjust the feet. - Re-centre by adjusting the rear feet. The upper basket does not stay - Poor manipulation (the basket - Act more progressively (see in the high position is being pulled upwards too instructions), one side and quickly) then the other. Small leak around or under the - Leak from the tap. appliance (move the appliance - Leak from the appliance. to locate the leak) (Cf. table fault d07). Small leak at the door - Check that a seal is fitted and retighten the nut. - Close the water tap and call a technician. - Appliance not stable or not level - Adjust the feet. - Door not centred on the tub. - Re-centre by adjusting the rear feet. 57 EN 14/ IF OPERATING ABNORMALITIES OCCUR • THE INDICATOR LIGHTS Problem The salt light does not go out Possible Causes What to do? - No salt or an insufficient quan- - Refill the tank and wait for the tity of salt in the tank to trigger cycle to end. If you have soft the float. water that requires no salt, the light is constantly lit. The lights all light up one after - Wrong programme. the other A light flashes and the pro- - Programme selector wrongly gramme does not start positioned (between two notches) - Cancel the current programming by holding down the Start button for 3 seconds and then re-programme. - Reposition the selector on a programme. • RELATING TO PROGRAMMING, DISPLAY Problem The cycle lasts too long Possible Causes What to do? - The energy-saving programmes last longer because the agitation and drying times are longer to compensate for the lower washing and drying temperatures - Use these programmes preferably at night when it is not so important how long the programme lasts or when it ends. The appliance trips the circuit - Insufficient amperage to supbreaker ply all the appliances being operated simultaneously. - Internal fault in the appliance. The appliance does not start - Check the socket’s amperage (10A minimum) and the meter’s capacity. - Call a technician. - No mains power to the socket. - Check the socket and the fuse - Tap closed (Cf. table fault d01). - Check the tap is open. - Check the hose line is OK. - Water supply hose kinked. - Selection error or programme - Cancel by holding down Start for 3 secs and re-programme. blocked. - Start button pressed too long - Just press Start briefly to start the programme. (greater than 2 secs). - Appliance in Safety mode (anti- - Call a technician. leak) (Cf. table fault d07). 58 EN 14/ IF OPERATING ABNORMALITIES OCCUR Problem Possible Causes What to do? The appliance will not restart - Door opened during a washing cycle. - Wait for the time delay to end (controlled internally by the appliance). The appliance does not drain (Cf. table fault d02). - The cover has not been remo- - Remove the cover. ved from the sink’s U-bend. - Check the drain hose line - Drain hose kinked. behind the machine is OK. - Remove and clean the filters - Filters totally blocked. and the drain. Initiate a Soaking programme - Pump blocked. If the fault persists, call a technician. • POOR WASHING RESULTS Problem Possible Causes What to do? Food traces and deposits in the - Items poorly arranged (mas- - Arrange the items properly. glasses ked by another larger item or Use the most appropriate situated underneath it, items areas and accessories for each nested or jammed together). type of item (see instructions). - Upper spray arm blocked by - Check that the spray arm cutlery or a dish etc. rotates freely. Set the basket in the high position if necessary. - Check the filter’s facing and that - Filter poorly locked and lifting the filter is locked in place (push it in fully, turning it to the right). during washing. - Remove all the filters and clean them (in warm water), including - Micro filter screen clogged. the micro filter’s screen (once a month). - Remove the spray arm by turn- One or more holes in the spray ing the lever a quarter of a turn and clean it under the tap (do arm blocked. not use any tool that could damage the holes). Re-install the spray arm. Traces of grease - Detergent dose too low; inefficient detergent; stale product. - Inappropriate programme (temperature too low; duration too short). 59 - Increase the dose; try another detergent. - Select a programme with a higher temperature. EN 14/ IF OPERATING ABNORMALITIES OCCUR • POOR WASHING RESULTS... Problem White marks (identify what type) Possible Causes - Chalky film (removable with vinegar). - Traces of salt (items have a salty taste). White marks (identify what type) - Glass cloudy because water too soft (cannot be removed). Coloured marks (tea, wine, cof- - Items poorly arranged fee) - Detergent dose too low; inefficient detergent - Programme temperature too low. - If you use a multifunction product. What to do? - Check that there is salt in the tank (light unlit = OK). - Check the water hardness at the tap and that the water softener is set correctly. Adjust it to a higher level if necessary. - Water too hard for using a “4in-1” detergent without the addition of salt. - Check that the stopper on the salt container is closed correctly. - Check the water hardness at the tap and that the water softener is set correctly. Some detergents in pellet form are more aggressive to glasses and decorations (change the product and use a protective product if necessary). - Turn the cavities in the items towards the jets. - Increase the dose; try another detergent. - Select a more suitable programme with a higher temperature. - Use the “4-in-1” option (depending on the model). Streaks or dried droplets on - Lack or insufficient amount of - Check the indicator light and glasses fill the tank completely. Adjust rinsing product. the dispensing unit to a higher position if necessary. - Rinsing product out-of-date or - Use a recent product (a good inefficient. product dilutes easily and foams in cold water). - If you use a multifunction - Use the “4-in-1” option with a product. setting prioritizing drying (parametering from the menu – depending on the model). Dried-on marks on glasses, dull- - If you use a multifunction - Use the “4-in-1” option with a ness. product. setting prioritizing brilliance (parametering from the menu – depending on the model). 60 EN 14/ IF OPERATING ABNORMALITIES OCCUR • POOR OPERATION Problem Possible Causes What to do? Constant filling - Drain hole situated too low for - Drain wand has fallen on the the appliance (Cf. table fault floor. d012). A lot of waste on the large filter - The filters and drain outlets are - Remove and clean the filters blocked with too much and the bottom of the drain at the end of the cycle. residue. outlets. Remove large residue from the plates before putting them in the machine. Traces of rust on stainless steel - Quality of the stainless steel ; - Use “special dishwasher-safe” not dishwasher-safe (knives in cutlery. - Check that the lid on the salt conparticular) tainer is closed correctly. • POOR DRYING RESULTS Problem Possible Causes What to do? A lot of droplets on the glasses - Lack or insufficient amount of - Check the indicator light and rinsing product. fill the tank completely. - The dose has not been distrib- - If the tank is not empty after uted. approximately 60 washings, call a technician. - Positioning of the items. - Arrange the items to restrict water retention as much as possible. Leave the door ajar for a few minutes, if possible Droplets on plastic items, Tefal - These items have a low calori- - Arrange the items in the upper coatings, etc. fic mass. basket. Poorer drying on rapid programmes - On rapid programmes, the drying - Leave the door ajar for a few temperature and drying period are minutes. reduced to cut down the duration of the cycle as much as possible. Condensation on the wall of the - Condensation may form on the inside door or the tub. walls, particularly after the appliance has cooled down (sound insulation increases this occurance) 61 EN 14/ IF OPERATING ABNORMALITIES OCCUR • CHANGING THE BULB You can change the bulb (halogen type G412V-5W) located on the left under the top cover. To do this: Important : Unplug the power cable before changing the bulb. (depending on the model) — Remove the top cover by unscrewing the two screws under the top cover’s lip (Fig. 16 A ). — Remove the top cover by unclipping it from the back of the appliance and then pushing it a few centimetres (Fig. 16 B ). — Lift off your dishwasher’s top cover (Fig. 16 B ). — Remove the 2 top screws from the protective plate and remove the plate (Fig. 16 C ). Screw A (depending on the model) B Important : For safety reasons, do not touch the two other screws. — Open the cover by pinching the 2 clips (Fig. 16 D ). — Remove the bulb/bulb holder assembly from its housing (Fig.16 E ). Important : C Use a soft cloth to manipulate the bulb. D — Change the bulb by freeing it from its housing (Fig.16 F ). — To re-install the bulb, follow the above instructions in reverse order. E F Fig. 16 62 EN 15/ AFTER-SALES SERVICE • INTERVENTION WORK Any intervention work on your appliance must be performed by a qualified professional approved by the manufacturer. When you call, please mention the full reference for your appliance (model, type and serial number). This information is shown on the description plate (see Fig. 17) ORIGINAL PARTS When maintenance is being carried out, ask for only certified original spare parts to be used. Fig. 17 63 EN 15/ INDICATIONS FOR THE TESTING LABORATORIES • Details common to all models — Washing capacity - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12 standard place settings — Arrangement of the items - - - - - - - - - - - - - - - - - - - - - - - - - - - - Figs. A-B-C; see next page — Loading as per the indications on next page, without side shelves — Setting for upper basket - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Low position — Setting for rinsing product distributor - - - - - - - - - - - - - - - - - - 3 — Adjusting the water softener - - - - - - - - - - - - - - - - - - - - - - - - - - H2 For detailed information on the comparison tests regarding the level of soiling, the types of crockery and cutlery, etc., contact the equipment manufacturer before commencing the tests. • Tests to Standard EN 50242: — Recommended programme - - - - - - - - - - - - - - - - - - - - - - - - - - — Dosage of detergent - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 30g of detergent B • Tests according to the mixed IEC 436/DIN 44990 method — Recommended programme - - - - - - - - - - - - - - - - - - - - - - - - - - — Dosage of detergent - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - “Eco” 5 + 25g. NB: When conducting tests using a multi-function tablet: H0 or H1 or H2 - Check that the water softener is correctly set for the water hardness — Pull out the detergent distribution drawer and place the tablet in the interior compartment. • Measuring the noise level in accordance with Standard EN60704-2-3: — Align the plinth on the housing unit with the door panel. 64 EN 15/ INDICATIONS FOR THE TESTING LABORATORIES A B 1 NOK NOK 2 3 4 OK 5 6 7 8 3 32 65 8 8 8 8 8 8 1 1 1 1 1 1 33 3333 2 33 3 222 1 8 8 8 6 6 8 8 8 5 444 3 4 4 4 44 4 11 C 7 2 2 2 2 2 111 22 444 EN NOTES 66 EN NOTES 67 After Sales Service: NL De eventuele ingrepen in de machine moeten worden uitgevoerd : - of door uw vakhandelaar, - of door een andere gekwalificeerd technicus van dit merk. Tijdens het telefoneren, dient u de complete referentie op te geven van uw machine (model, type, serienummer). Deze informatie staat op het typeplaatje op de machine. Any maintenance on your equipment should be undertaken by: - either your dealer, - or another qualified mechanic who is an authorized agent for the brand appliances. When making an appointment, state the full reference of your equipment (model, type and serial number). This information appears on the manufacturer's nameplate attached to your equipment. Service après vente : PL Wszelkie czynności serwisowe wykonywane na urządzeniu muszą być wykonane przez: - sprzedawcę, - wyspecjalizowany zakład naprawczy posiadający atest producenta. Aby przyspieszyć i ułatwić obsługę prosimy o podanie dokładnych danych dotyczących urządzenia (model, typ, numer seryjny). Wszystkie te dane znajdują się na tabliczce znamionowej umieszczonej na urządzeniu. Les éventuelles interventions sur votre appareil doivent être effectuées : - soit par votre revendeur, - soit par un autre professionnel qualifié dépositaire de la marque. Lors de votre appel, mentionnez la référence complète de votre appareil (modèle, type et numéro de série). Ces renseignements figurent sur la plaque signalétique fixée sur votre appareil. DE Kundendienst : CS Eingriffe an Ihrem Gerät dürfen nur: - von Ihrem Händler oder - von einem sonstigen Fachmann und Vertragshändler der Marke durchgeführt werden. Geben Sie bei der Meldung einer Störung die vollständige Typenbezeichnung Ihres Gerätes an (Modell, Typ, Seriennummer). Diese Angaben finden Sie auf einem an Ihrem Gerät angebrachten Schild. ES Servicio postventa : RU Cepcoe ocyae: , : - , ; - , . ( , ). ! ", . Serviços autorizados : EL Tεχνική υποστήριξη: Οι ενδεχόμενες επεμβάσεις πάνω στη συσκευή σας θα πρέπει να διενεργούνται: - είτε από τον προμηθευτή σας, - είτε από το κατά τόπους εξουσιοδοτημένο σέρβις. Σε περίπτωση που τηλεφωνήσετε, θα πρέπει να αναφέρετε όλα τα στοιχεία της συσκευής σας (μοντέλο, τύπο και αριθμό σειράς).Τα στοιχεία αυτά αναγράφονται στην ετικέτα των χαρακτηριστικών του κατασκευαστή που βρίσκεται πάνω στη συσκευή. Qualquer intervenção no seu aparelho deve ser realizada: - quer pelo seu revendedor, - quer por outro profissional qualificado autorizado pela marca. Ao chamá los, indique a referência completa do seu aparelho (modelo, tipo e número de série). Estas informações figuram na placa de identificação fixada no aparelho. DA Záruční servis: Případné opravy na přístroji může provádět pouze : - váš prodejce - nebo záruční opravna, která má smlouvu s výrobcem Při telefonickém styku uvádějte úplné označení vašeho přístroje (model, typ a výrobní číslo). Tyto údaje jsou uvedeny na výrobním štítku přístroje. Las intervenciones que requiera la máquina deberán ser efectuadas: - por el revendedor, - o por cualquier profesional cualificado depositario de la marca. Al llamar, mencione la referencia completa de la máquina (modelo, tipo y número de serie). Estos datos figuran en la placa de identificación situada en la máquina. PT Usługi serwisowe : Kundeservice : Eventuel vedligeholdelse af apparatet skal foretages: - enten af Deres forhandler, - eller af en kvalificeret fagmand, som er anerkendt til dette mærke. Når De ringer op, skal De angive apparatets fulde reference (model, type, serienummer). Disse oplysninger står på typeskiltet, der sidder på apparatet. Photographie de couverture/front cover photography: Michel Gibert 68 DVH740,- B3798-B-1/3-01/07 FR Serviceafdeling: Brandt Appliances - SAS au capital de 10.000.000 euros - RCS Nanterre 440 302 347 EN
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project