Casio CASIO 5096 Operation Guide

Add to my manuals
3 Pages

advertisement

Casio CASIO 5096 Operation Guide | Manualzz
MA0909-EA
Operation Guide 5096 (OC)
Power Levels
Congratulations upon your selection of this CASIO watch.
B
You can get an idea of the watch’s power level by observing the movement of the
x Second Hand in the regular timekeeping.
••If the x Second Hand is moving normally at one-second intervals, power is at
Level 1.
••If the x Second Hand is moving at two-second intervals, power is at Level 2,
which is quite low. Expose the watch to light as soon as possible so it can
charge.
+
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss suffered by you
or any third party arising through the use of this product or its malfunction.
About This Manual
B
@ + >
Level
Button operations are indicated using the letters A through C shown in the
illustration.
Hand Functions
Moves at two-second
intervals.
<Regular timekeeping>
z Hour Hand
x Second Hand
c Minute Hand
v 24-hour Hand
*
6
<Stopwatch>
b Stopwatch Second Hand
n Stopwatch Minute Hand
Function Status
Normal.
All functions enabled
2
x Second Hand moves at two-second
intervals.
Time calibration signal reception
disabled
3
z Hour Hand, x Second Hand and
c Minute Hand stopped at 12 o’clock.
All functions disabled
••When power drops to Level 3, all functions will be disabled but the watch will
continue to keep time internally for about one week. If you recharge the battery
sufficiently during this period, the analog hands will move automatically to the
correct setting and regular timekeeping will resume. After one week, all settings
(including timekeeping) will be cleared. Recharging the battery will reset all
settings to their initial factory defaults.
Charging Times
This User’s Guide uses numbers shown above to identify watch hands.
Important!
The A button is designed to protect against accidental pressing. Use a thin
pointed object to press the depression of the button to operate it.
@
Hand Movement
1
Daily Operation
*1
Exposure Level (Brightness)
Level 1
8 minutes
3 hours
35 hours
Window sunlight (10,000 lux)
30 minutes
8 hours
134 hours
Window sunlight on cloudy day (5,000 lux)
48 minutes
13 hours
216 hours
8 hours
149 hours
–––
**1 Approximate exposure each day to generate power for normal daily operation.
**2 Approximate exposure to take power up one level.
••The above times are for reference only. Actual times depend on lighting conditions.
••For details about the operating time and daily operating conditions, see the “Power Supply” section of the
Specifications.
Things to check before using the watch
1. Press C to enter the regular timekeeping, observe the movement of the x Second Hand.
Is the x Second Hand moving smoothly at one-second intervals?
NO
YES
The watch is charged sufficiently. For details
about charging, see “Charging the Watch”.
NEXT
YES
Power is low. Charge the watch by placing it in a
location where it is exposed to light. For details, see
“Charging the Watch”.
Level 2
Outdoor sunlight (50,000 lux)
Indoor fluorescent lighting (500 lux)
Is the x Second Hand moving at two-second intervals
or is it stopped completely?
Level Change *2
Level 3
Go to step 2.
Power Saving
Power Saving enters a sleep state automatically whenever the watch is left for one week in an area where it
is dark.
What happens when the watch is in the sleep state
••All hands move to 12 o’clock and stop.
••Auto Receive becomes disabled.
••Internal timekeeping functions continue to operate normally.
To recover from the sleep state
Move the watch to a well-lit area or press any button.
Radio Controlled Atomic Timekeeping
2. Check the current location setting.
Use the procedure under “Specifying Your Current Location and Setting the Time” to configure your location
setting.
This watch receives a time calibration signal and updates its time setting accordingly. However, when using
the watch outside of areas covered by time calibration signals, you will have to adjust the settings manually as
required. See “Specifying Your Current Location and Setting the Time” for more information.
Important!
Proper time calibration signal reception and time settings depend on correct location setting. Make sure you
configure these settings correctly.
This section explains how the watch updates its time settings when the city name selected as the current
location is in Japan or China, and is one that supports time calibration signal reception.
3. Set the current time.
••To
set the time using a time calibration signal
See “To get ready for a receive operation”.
••To
set the time manually
See “Specifying Your Current Location and Setting the Time”.
If your location setting is this:
The watch can receive the signal from the transmitter located here:
HONG KONG (HKG)
Shangqiu City (China)
TOKYO (TYO)
Fukushima (Japan), Fukuoka/Saga (Japan)
Approximate Reception Ranges
Japanese Signal
The watch is now ready for use.
••For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic
Timekeeping”.
Chinese Signal
Fukushima
500 kilometers
Shangqiu
Shanghai
Chengdu
Hong Kong
Charging the Watch
The face of the watch is a solar cell that generates power from light. The generated power charges a built-in
rechargeable battery, which powers watch operations. The watch charges whenever it is exposed to light.
1,000 kilometers
Charging Guide
When wearing the watch, make
sure that its face is not blocked
from light by the sleeve of your
clothing.
••The watch may enter a sleep
state if its face is blocked by your
sleeve even only partially.
Warning!
Leaving the watch in bright light for charging can cause it to become quite hot. Take care when
handling the watch to avoid burn injury. The watch can become particularly hot when exposed to the
following conditions for long periods.
••On the dashboard of a car parked in direct sunlight
••Too close to an incandescent lamp
••Under direct sunlight
Important!
••Keep the watch in an area normally exposed to bright light when storing it for long periods. This helps to
ensure that power does not run down.
••Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is
blocked from exposure to light can cause power to run down. Make sure that the watch is exposed to bright
light whenever possible.
Changchun
Beijing
Fukuoka/Saga
Whenever you are not wearing
the watch, leave it in a location
where it is exposed to light.
••Best charging performance
is achieved by exposing
the watch to light that is as
strong as possible.
500 kilometers
1,500 kilometers
••Even when the watch is within range of a transmitter, signal reception may be impossible due to the effects
of geographic contours, structures, weather, the time of year, the time of day, radio interference, etc. The
signal becomes weaker at distances of approximately 500 kilometers, which means that the influence of the
above conditions becomes even greater.
••Signal reception may not be possible at the distances noted below during certain times of the year or day.
Radio interference may also cause problems with reception.
−−Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)
−−Shangqiu (China) transmitter: 500 kilometers (310 miles)
••As of January 2009, China does not use Daylight Saving Time (DST). If China does go to the Daylight
Saving Time system in the future, some functions of this watch may no longer operate correctly.
To get ready for a receive operation
1. The antenna of this watch is located on its 12 o’clock side. Position the watch with 12 o’clock facing towards
a window as shown in the nearby illustration. Make sure there are no metal objects nearby.
••Signal reception normally is better at night.
••The receive operation takes from two to seven minutes, but
in some cases it can take as long as 14 minutes. Take care
12 o’clock
that you do not perform any button operation or move the
watch during this time.
or
1
Operation Guide 5096 (OC)
••Signal reception may be difficult or even impossible under the conditions described below.
Inside or among
buildings
Inside a vehicle
Near household
appliances,
office equipment,
or a mobile
phone
Near a
construction
site, airport, or
other sources of
electrical noise
Near hightension power
lines
Among or behind
mountains
2. What you should do next depends on whether you are using Auto Receive or Manual Receive.
••Auto Receive: Leave the watch over night in the location you selected in step 2. See “Auto Receive” for
details.
••Manual Receive: Perform the operation under “To perform manual receive”.
Specifying Your Current Location and Setting the Time
Use the procedure in this section to specify the location where you will be using the watch. You also can adjust
the time when the watch is unable to receive a time calibration signal.
1. In the regular timekeeping, keep A depressed (for about five seconds) as
@
the x Second Hand and b Stopwatch Second Hand go through the sequence
described below.
••x Second Hand: Last signal reception result → RC → Current location setting
••b Stopwatch Second Hand: 30 (Indicates the setting mode.)
2. Press C to select the location you want.
••Each press of C cycles through the three settings shown below.
City Name
*
Auto Receive
••With Auto Receive, the watch performs the receive operation each day automatically up to three times
between the hours of 2 a.m. and 4 a.m. (1 a.m. and 3 a.m. for the Chinese calibration signal). When any
receive operation is successful, none of the other receive operations for that day are performed.
••When a calibration time is reached, the watch will perform the receive operation only if it is in the regular
timekeeping. The receive operation is not performed if a calibration time is reached while you are
configuring settings.
@
When the x Second Hand is
pointed here:
It means this:
Receiving (RC)
Reception is in progress.
YES (Y)
Reception was completed successfully.
NO (N)
Reception failed for some reason.
3. The receive operation is complete when the x Second Hand moves to YES (Y)
or NO (N) for about five seconds, and then resumes regular timekeeping.
••You can return to the regular timekeeping manually by pressing A while the
x Second Hand is pointing to YES (Y) or NO (N).
••When the receive operation is successful, the watch adjusts the time setting
accordingly. It does not adjust the setting if the operation failed.
*
>
Note
••To interrupt a receive operation and return to the regular timekeeping, press
any button.
@
Timekeeping
B
@ + >
Hand Functions
<Regular timekeeping>
z Hour Hand
x Second Hand
c Minute Hand
v 24-hour Hand
*
6
<Stopwatch>
b Stopwatch Second Hand
n Stopwatch Minute Hand
Receive off*
4. Use the C (+1 minute) and B (–1 minute) buttons to change the current time
setting.
••Holding down either button for about two seconds and then releasing it starts
high-speed hand movement in the applicable direction.
••Pressing C and B at the same time will start high-speed hand movement,
which will continue until the hands complete a 24-hour rotation.
••To stop high-speed hand movement, press any button.
••Check the v 24-hour Hand to make sure that the time is set properly
(1:00 a.m. = 1 o’clock, 1:00 p.m. = 13 o’clock).
Using the Stopwatch
The stopwatch measures elapsed time.
Hand Functions
Note
••The x Second Hand will indicate NO (N) if you have adjusted the time setting
manually since the latest receive operation.
Radio-controlled Atomic Timekeeping Precautions
••Strong electrostatic charge can result in the wrong time setting.
••Even if a receive operation is successful, certain conditions can cause the time setting to be off by up to
one second.
••If you are in an area where signal reception is not possible, the watch keeps time with the precision noted
in “Specifications”.
••The receive operation is disabled under any of the following conditions.
−−While power is at Level 2 or lower
−−When the watch is in the function sleep state (“Power Saving”)
OFF
5. After the setting is the way you want, press A.
••This will exit the setting mode and the x Second Hand will resume regular
timekeeping.
••For best timekeeping accuracy, press A on a time signal from the TV or radio.
••The watch will exit the setting mode automatically if you do not perform any
button operation for about two or three minutes.
@
To check the result of the latest receive operation
In the regular timekeeping, press A.
••The x Second Hand will move to YES (Y) for five seconds if the latest receive
operation was successful, or NO (N) if it was not. After that, regular timekeeping
will resume.
••You can return to the regular timekeeping manually by pressing A while the
x Second Hand is pointing to YES (Y) or NO (N).
China
3. Press A. What you should do next depends on the location setting you selected
in step 2.
••If you selected OFF, the x Second Hand and b Stopwatch Second Hand
will move to 12 o’clock, which indicates the hour and minute setting mode.
Proceed to step 4, below.
••If you selected TOKYO (TYO) or HONG KONG (HKG) for the location setting,
pressing A will return to regular timekeeping. The hands of the watch will
move to the current time in the location you selected, which completes this
setting procedure.
@
2. The x Second Hand indicates the operations the watch is currently performing.
Japan
HONG KONG (HKG)
**Select OFF for the location setting whenever using the watch in any other
geographic area other than Japan or China. When OFF is selected, the watch
does not receive any time calibration signal, so you will need to adjust the time
setting manually as required.
TOKYO (TYO)
To perform manual receive
1. In the regular timekeeping, keep A depressed (for about two seconds) as the x Second Hand goes
through the following sequence.
••Moves to YES (Y) or NO (N) to indicate the last signal reception result, then to Receiving (RC).
Location
TOKYO (TYO)
b S
topwatch Second Hand
n Stopwatch Minute Hand
To perform an elapsed time operation
B
Start
*
B
Stop
B
(Restart)
B
(Stop)
C
Reset
6
Note
••The Stopwatch Mode can indicate elapsed time up to 20 minutes, 00 seconds.
••Resetting the stopwatch will cause the n Stopwatch Minute Hand and b Stopwatch Second Hand to rotate
counterclockwise until they reach their 12 o’clock positions. In some cases, the stopwatch second hand will
move counterclockwise to 12 o’clock and then make one full rotation clockwise before stopping.
Hand Home Position Adjustment
If the time setting of your watch is not correct even though time calibration signal reception is being performed
normally, use the procedure in this section to check the home positions of the hands and make adjustments
as required.
Note that you do not need to perform the following operation if your watch is showing the correct time.
Important!
••When performing the following procedure, it is recommended that after you move to a home position, you
press the B button to move the setting back one step. Next, press the C button to return it to the home
position. This helps to ensure better home position adjustment accuracy.
@
+
1. In the regular timekeeping, hold down A for about 10 seconds until the
c Minute Hand and x Second Hand move to 12 o’clock.
••The x Second Hand goes through the sequence described below.
Last signal reception result → RC → Current location setting → Keep A
depressed until the x Second Hand starts to move counterclockwise. You can
release A at this time.
••The c Minute Hand and x Second Hand are in their correct home positions if
they are pointed precisely at 12 o’clock. If the hands are in the correct home
positions, advance to step 4.
2
Operation Guide 5096 (OC)
If the current home positions are within ±15 minutes 00 seconds
2. Use C (+1 second) and B (–1 second) to adjust the hand positions so they
@
+
point to 12 o’clock.
••Holding down either button for about two seconds and then releasing it starts
high-speed hand movement in the applicable direction.
••To stop high-speed hand movement, press any button.
••After adjusting the home positions, go to step 4.
If the current home positions is greater than ±15 minutes 00 seconds
2. After performing step 1, hold down the C and B buttons at the same time until
B@
+
the z Hour Hand, c Minute Hand, x Second Hand, and v 24-hour Hand all
move to 12 o’clock.
>
*
6
Specifications
Accuracy at normal temperature: ± 15 seconds a month (with no signal calibration)
Timekeeping: Hour, minutes (hand moves every 10 seconds), seconds, 24-hour
Time Calibration Signal Reception: Auto receive up to three times a day; Manual receive
Receivable Time Calibration Signals:
Fukushima, Japan (Call Sign: JJY, Frequency: 40.0 kHz); Fukuoka/Saga, Japan (Call Sign: JJY,
Frequency: 60.0 kHz); Shangqiu City, Henan Province, China (Call Sign: BPC, Frequency:
68.5 kHz)
Stopwatch: Measuring capacity: 20’00”
Measuring unit: 1 second
Measuring mode: Elapsed time
Other: Power Saving
Power Supply: Solar cell and one rechargeable battery
Approximate battery operating time: 8 months (no exposure to light after a full charge; signal reception of
approximately 3 minutes per day)
3. Use C (+1 second) and B (–1 second) to adjust the hand positions so they
point to 12 o’clock.
••Holding down either button for about two seconds and then releasing it starts
high-speed hand movement in the applicable direction.
••To stop high-speed hand movement, press any button.
••The v 24-hour Hand is synchronized with the z Hour Hand and c Minute
Hand, so separate adjustment is not required.
••After adjusting the home positions, go to step 4.
4. Press A. This will cause the n Stopwatch Minute Hand and b Stopwatch
Second Hand to move to 12 o’clock for home position adjustment.
••The n Stopwatch Minute Hand and b Stopwatch Second Hand are in their
correct home positions if they are pointed precisely at 12 o’clock. If the hands
are in the correct home positions, advance to step 6.
5. Use C (+1 second) and B (–1 second) to adjust the hand positions so they
point to 12 o’clock.
••Holding down either button for about two seconds and then releasing it starts
high-speed hand movement in the applicable direction.
••To stop high-speed hand movement, press any button.
••After adjusting the home positions, go to step 6.
6. Press A to exit home position correction and return to regular timekeeping.
Troubleshooting
Hand Movement and Position
x Second Hand is moving at two second intervals.
■■The
■■All
the watch’s hands are stopped at 12 o’clock and none of the buttons work.
Power may be low. Expose the watch to light until the x Second Hand starts moving normally, at one-second
intervals.
■■The hands of the watch suddenly start moving at high speed, even when I do not perform any
operation.
This could be due to any one of the following causes. In all cases, the hand movement does not indicate
malfunction, and should stop shortly.
••The watch is recovering from a sleep state.
••The time setting is being adjusted following a successful auto time calibration signal receive operation.
■■The current time setting is off by hours.
Your location setting may be wrong. Check your location setting and correct it, if necessary.
■■The hands are off.
This could indicate that the watch has been exposed to magnetism or strong impact, which has caused
problems with proper hand alignment. Adjust the watch’s hand home position alignment.
Charging
■■The
watch does not resume operation after I expose it to light.
This can happen after the power level drops to Level 3. Continue exposing the watch to light until the x
Second Hand starts moving normally (at one-second intervals).
x Second Hand starts to move at one-second intervals, but then suddenly returns to moving at
■■The
two-second intervals.
The watch probably is not sufficiently charged yet. Continue keeping it exposed to light.
Time Calibration Signal
The information in this section applies only when HONG KONG (HKG) or TOKYO (TYO) is selected as the
current location. You need to adjust the current time manually when OFF is selected as the current location.
x Second Hand indicates NO (N) when I check the result of the latest receive operation.
■■The
Possible Cause
Remedy
••You are wearing or moving the watch, or performing a
button operation during the signal receive operation.
••The watch is in an area with poor reception conditions.
Keep the watch in an area where reception conditions
are good while the signal receive operation is being
performed.
You are in an area where signal reception is not possible
for some reason.
See “Approximate Reception Ranges”.
The calibration signal is not being transmitted for some
reason.
••Check the website of the organization that maintains the
time calibration signal in your area for information about
its down times.
••Try again later.
■■The
current time setting changes after I set it manually.
You may have the watch configured for Auto Receive of the time calibration signal, which will cause the time to
be adjusted automatically according to your currently selected location. If this results in the wrong time setting,
check your location setting and correct it, if necessary.
■■Auto
Receive is not performed or I cannot perform Manual Receive.
Possible Cause
Remedy
Your location setting is wrong.
Check your location setting and correct it, if necessary.
There is not enough power for signal reception.
Expose the watch to light to charge it.
■■Signal
reception is being performed successfully, but the time is wrong.
Possible Cause
Remedy
Your location setting is wrong.
Check your location setting and correct it, if necessary.
The watch may have been exposed to magnetism or
strong impact, which has caused problems with proper
hand alignment.
Adjust the watch’s hand home positions.
3

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement