Casio Watch 2654 User's Manual

MO0302-A
USER’S GUIDE 2534/2654
Getting Acquainted
About This Manual
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to carefully read this manual and keep it on hand for later reference
when necessary.
Expose the watch to bright light to charge its battery before using it.
You can use this watch even as its battery is being charged by exposure to bright
light.
• Be sure to read “Battery” of this manual for important information you need
to know when exposing the watch to bright light.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
(Light)
If the display of the watch is blank...
If the SLEEP indicator is on the display, it means that the
display is blank because the watch’s Power Saving
function has turned off the display to conserve power.
Power Saving automatically turns off the display and puts
the watch into a sleep state whenever your watch is left for
a certain period where it is dark.
• The initial factory default setting is Power Saving on.
• The watch recovers from the sleep state if you move it to
a well-lit area , if you press any button, or if you angle
the watch towards your face for reading.
It can take up to five seconds for the display to turn on.
• See “Power Saving Function” for more information.
*
*
Telememo Mode
General Guide
World Time Mode
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
▲
▲
Timekeeping Mode
Press C.
▲
▲
Stopwatch Mode
Countdown Timer Mode
▲
Alarm Mode
H
Timekeeping
Hour : Minutes Seconds
Year
Use the Timekeeping Mode to set and view the current
time and date.
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Seconds
Hour
Minutes
12/24-Hour
Format
To create a new Telememo record
1. In the Telememo Mode, use B and D to cycle through
Name area
the record screens until the new data screen appears.
• The new data screen is the one that is blank (contains
no name and telephone number).
• If the message FULL appears on the display, it
means that memory is full. To store another record,
you will first have to delete some of the records stored
in memory.
Number area
New Data Screen
Day of week
Month – Day
Power Saving
PM indicator
Day
Month
2. Hold down A until the flashing cursor (_) appears in
the name area of the display.
3. In the name area, use D and B to cycle through
characters at the cursor position. The characters cycle
in the sequence shown below.
Year
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Setting
Screen
Button Operation
Seconds
Press D to reset to 00.
Hour, Minutes
Use D (+) and B (–) to change the setting.
12/24-Hour
Format
Press D to toggle between 12-hour (12H) and
24-hour (24H) timekeeping.
Year,Month,Day
Use D (+) and B (–) to change the setting.
Power Saving
Press D to toggle Power Saving on (ON) and
off (OFF).
4. Press A to exit the setting screen.
• See “Power Saving Function” for details about configuring Power Saving settings.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Press D.
(space)
Remaining memory
Name
-
.
:
/
4. When the character you want is at the cursor position, press C to move the cursor
to the right.
5. Repeat steps 3 and 4 until the name is complete.
• You can input up to eight characters for the name.
6. After you input the name, press C as many times as necessary to move the cursor
to the number area.
• When the cursor is located at the eighth space of the name area, moving the
cursor to the right causes it to jump to the first digit of the number. When the
cursor is at the 12th digit of the number, moving it to the right (by pressing C)
causes it to jump to the first character in the name.
7. In the number area, use D and B to cycle through numbers and symbols
(hyphen, space) at the cursor position. The characters cycle in the sequence shown
below.
Press B.
The Telememo Mode lets you store up to 30 records, each
containing name and telephone number data. Records are
automatically sorted based on the characters of the name.
You can recall records by scrolling through them on the
display.
• See “Sort Table” for details on how the watch sorts
records.
• All of the operations in this section are performed in the
Telememo Mode, which you enter by pressing C.
0 to 9
Press B.
Press D.
Telememo
A to Z
x
0 to 9
(space)
8. When the character you want is at the cursor position, press C to move the cursor
to the right.
9. Repeat steps 7 and 8 until you complete number input.
• You can input up to 12 digits for the number.
10. After inputting your data, press A to store it.
• After data storage is complete, the cursor appears in the name area of the
display, ready for input of a new Telememo record.
11. Input more data (starting from step 3) or press A again to return to the Telememo
record screen (without the cursor).
• The name can show only three characters at a time, so longer text scrolls
continuously from right to left. The last character is indicated by the symbol after it.
Telephone number
1
USER’S GUIDE 2534/2654
To recall Telememo records
In the Telememo Mode, use D (+) and B (–) to scroll through Telememo records on
the display.
• Pressing D while the last Telememo record is on the display or B while the first
record is on the display displays the new data screen.
To edit a Telememo record
1. In the Telememo Mode, use D (+) and B (–) to scroll through the records and
display the one you want to edit.
2. Hold down A until the flashing cursor appears on the display.
3. Use C to move the flashing to the character you want to change.
4. Use D (+) and B (–) to change the character.
5. After making the changes that you want, press A to store them and return to the
Telememo record screen.
Reset Time
You can set a “reset time,” which is a kind of alternate countdown start time you can
recall with the press of a button any time a countdown operation is in progress.
Timer Mode
The countdown timer gives you a choice of two modes: auto-repeat and elapsed time.
Auto-repeat
Auto-repeat mode automatically restarts the countdown from the countdown start time
you set whenever zero is reached.
• Auto-repeat mode is best when timing the starts of match races.
• Even if you start a countdown operation from the reset time, the countdown
automatically restarts from the countdown start time whenever it reaches zero.
• Auto repeat timing repeats up to seven times.
To delete a Telememo record
1. In the Telememo Mode, use D (+) and B (–) to scroll through the records and
display the one you want to delete.
2. Hold down A until the flashing cursor appears on the display.
3. Hold down D and B until the watch beeps and CLR stops flashing on the
display.
• The message CLR appears, which indicates that the record is being deleted.
After the record is deleted, the cursor appears on the display, ready for input.
4. Input data or press A to return to the Telememo record screen.
Elapsed Time
When the end of the countdown is reached in the elapsed time mode, the timer
automatically switches to an elapsed time measurement operation.
• The elapsed time mode is best when timing the speed of yachts during ocean races.
• The elapsed time operation is performed in one-second increments up to 99 hours,
59 minutes, 59 seconds.
World Time
Countdown End Beeper
The watch beeps each second of the final 10 seconds before a countdown reaches
zero, and at zero. The first five beeps (seconds 10 through 6) are higher pitched than
the final five beeps (seconds 5 through 1). The watch emits a longer beep to signal
when the countdown reaches zero.
• The countdown end beeper always sounds, regardless of the on/off status of the
progress beeper.
GMT differential
City Code
Timekeeping Mode time
The World Time Mode shows you the current time in 27
cities (29 time zones) around the world.
• The time settings of the Timekeeping Mode and the
World Time Mode are independent from each other, so
you must make separate settings for each.
• Whenever you change the time setting for any city in the
World Time Mode, the settings of all other cities are
changed accordingly.
• For full information on city codes, see the “City Code
Table”.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
Current time in the zone
of the selected city code
To view the time in another city code
In the World Time Mode, press D to scroll through city codes (time zones) to the east
or B to scroll to the west.
To set the World Time
1. In the World Time Mode, use D and B to scroll
through the city code (time zone) and find the one you
want.
2. Hold down A until the hour setting of the world time
starts to flash, which indicates the setting screen.
3. Press C to move the flashing between the hour and
minute settings.
4. While a setting is flashing, use D (+) and B (–) to
change it.
5. Press A to exit the setting screen.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D and B to display the
city code whose Standard Time/Daylight Saving Time
setting you want to change.
2. Hold down A until the hour setting of the world time
starts to flash, which indicates the setting screen.
3. Press L to toggle Daylight Saving Time ( displayed)
and Standard Time ( not displayed).
4. Press A to exit the setting screen.
• The Daylight Saving Time indicator appears while the
GMT differential is on the display only. It does not
appear while the city code is on the display.
• Note that you cannot switch between Standard Time
and Daylight Saving Time while GMT is selected as the
city code.
• Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
• The indicator is on the display whenever you display a
city code for which Daylight Saving Time is turned on.
Countdown Timer
Minutes
Seconds
The countdown timer can be set within a range of one
minute to 60 minutes. An alarm sounds when the
countdown reaches zero. The countdown timer has two
modes: auto-repeat and elapsed time, and a progress
beeper signals the progress of the countdown. All of this
makes the countdown timer a valuable tool for timing the
start of a yacht race.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
Timekeeping Mode time
C.
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep informed
about the countdown status without looking at the display. The following describes the
types of beeper operations the watch performs during a countdown.
Progress Beeper
The progress beeper actually includes two beepers: a reset time beeper and a reset
period progress beeper.
• The reset time beeper and reset period progress beeper sound only while the
progress beeper is turned on.
Reset Time Beeper
The reset time beeper is similar to the countdown end beeper. When the progress
beeper is turned on, the watch beeps each second of the final 10 seconds before the
countdown reaches the reset time.
Reset Period Progress Beeper
The reset period is the portion of the countdown between the reset time and zero.
When the progress beeper is turned on, the watch emits four short beeps at the top of
each minute during the reset period, and 30 seconds before the end of the
countdown.
Countdown Timer Examples
Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Auto-repeat;
Progress beeper: On
Reset Period
Start Time
• See “To configure the countdown timer” for information about setting up the timer.
Countdown
End Beeper
1'00" 0'30" 0'00"
Reset Period Progress Beeper
4'00"
3'00"
2'00"
Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Elapsed time;
Progress beeper: Off
Start Time
10'00"
Elapsed time
measurement
Reset Time
5'00"
Countdown
End Beeper
0'00"
To configure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the
countdown start time setting starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below to select other settings.
Start
Time
Reset
Time
Timer
Mode
Progress
Beeper
3. When the setting you want to change is flashing, use D and B to change it as
described below.
Setting
Screen
Button Operations
Start Time
Use D (+) and B (–) to change the setting.
• You can set a start time in the range of 1 to 60 minutes
in 1-minute increments.
Reset Time
Use D (+) and B (–) to change the setting.
• You can set a reset time in the range of 1 to 5 minutes
in 1-minute increments.
Timer Mode
Press D to toggle between the auto-repeat mode (ON)
and the elapsed time mode (OFF).
• An auto-repeat indicator ( ) appears when the autorepeat mode is selected.
Progress
Beeper
Press D to toggle progress beeper on (ON) and off (OFF).
• A progress beeper indicator ( ) appears when this
setting it turned on.
Configuring the Countdown Timer
The following are the settings you should configure before actually using the
countdown timer.
Countdown start time and reset time
Timer mode (auto-repeat, elapsed time)
Progress beeper on/off
Reset Time
5'00"
10'00"
Reset Time Beeper
4. Press A to exit the setting screen.
• The reset time setting must be less than the countdown start time setting.
2
USER’S GUIDE 2534/2654
To use the countdown timer
In the Countdown Timer Mode, press D to start the
countdown timer.
• The countdown timer measurement operation continues
even if you exit the Countdown Timer Mode.
• The table below describes button operations you can
perform to control countdown operations.
To select the operation of Alarm 1
1. In the Alarm Mode, use D to select Alarm 1.
2. Press B to cycle through the available settings in the sequence shown below.
SNZ indicator and one-time alarm on indicator
ALM
SNZ ALM
One-time alarm on
To do this:
Do this:
Stop the countdown operation
Press D.
Resume a stopped countdown operation
Press D again.
Display the countdown start time
While the countdown is
stopped, press B.
Stop the countdown operation and display the reset time
Press B.
Start the countdown from the displayed reset time
Press D.
• The table below describes button operations you can perform during an elapsed
time measurement operation in the elapsed time mode.
To do this:
Do this:
Stop the elapsed time operation
Press D.
Resume a stopped elapsed time operation
Press D again.
Display the countdown start time
While the elapsed time is
stopped, press B.
Stop the elapsed time operation and display the reset time
Press B.
Start the countdown from the displayed reset time
Press D.
Snooze alarm on
Alarm off
• The applicable alarm on indicator (ALM or SNZ ALM) is displayed in all modes
when an alarm is turned on.
• The SNZ indicator flashes during the 5-minute intervals between alarms.
• Displaying the Alarm 1 setting screen while the snooze alarm is turned on
automatically turns off the snooze alarm (making Alarm 1 a one-time alarm).
To turn the hourly time signal and the brightness alarm on and off
Hourly time signal on 1. In the Alarm Mode, use D to select the Hourly Time
Signal or the brightness alarm.
indicator
2. Press B to toggle the displayed item on and off.
• Turning on the Hourly Time Signal displays the hourly
time signal on indicator (SIG) on its screen.
• Turning on the brightness alarm displays the brightness
alarm on indicator (BRT) on its screen.
• The hourly time signal on indicator and brightness alarm
on indicator are displayed in all modes.
Brightness alarm on
indicator
Alarms
Alarm number
Alarm time
(Hour : Minutes)
Timekeeping Mode time
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other four are
one-time alarms.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour, and a
brightness alarm that beeps whenever the watch is moved
from an area where it is dark to an area where it is light.
• There are five alarm screens numbered 1 through 5.
The hourly time signal screen is indicated by :00. The
brightness alarm screen shows ON or OFF.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Stopwatch
Hours
Minutes
Seconds
1/100 second
To set an alarm time
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 99 hours, 59
minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed Time
x1
x2
x3
x4
D
Start
ON or OFF
:00
x5
• You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2
through 5 can be used as one-time alarms only.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash. This indicates the setting screen.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
➤D
Stop
➤D
Re-start
➤D
Stop
➤B
Clear
➤B
Split
➤B
Split release
➤D
Stop
➤B
Clear
➤D
Stop
➤B
Split release
➤B
Clear
Split Time
D
Start
(SPL displayed)
Two Finishes
➤B
Split
D
Start
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds. In the case of the snooze
alarm, the alarm operation is performed a total of seven times, every five minutes,
until you turn the alarm off or change it to a one-time alarm.
The watch also has a brightness alarm. When turned on, the brightness alarm causes
the watch to beep for 10 seconds when the watch is brought from the dark into the
light. The following are the conditions for brightness alarm operation.
• The watch needs to be in the dark for about 30 to 35 minutes for the brightness
alarm to become activated.
• The brightness alarm sounds about 15 to 20 minutes after the watch is next exposed
to light.
• The brightness alarm sounds only once and then turns off automatically.
Note
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the Alarm 1 setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn Alarms 2 through 5 on and off
1. In the Alarm Mode, use D to select a one-time alarm
One-time alarm on
(alarm number 2 through 5).
indicator
2. Press B to toggle the displayed alarm on and off.
• Turning on a one-time alarm (2 through 5) displays the
one-time alarm on indicator (ALM) on its screen.
• The one-time alarm on indicator is displayed in all
modes.
• If any alarm is on, the alarm on indicator is shown on
the display in all modes.
Backlight
Auto light switch
on indicator
The backlight uses an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch automatically turns on
the backlight when you angle the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• See “Backlight Precautions” for other important
information about using the backlight.
To turn on the backlight manually
In any mode, press L to illuminate the display for about
one second.
• The above operation turns on the backlight regardless of
the current auto light switch setting.
About the Auto Light Switch
Turning on the auto light switch causes the backlight to turn on for about one second,
whenever you position your wrist as described below in any mode. Note that this
watch features a “Full Auto EL Light,” so the auto light switch operates only when
available light is below a certain level. It does not turn on the backlight under bright
light.
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes the backlight to turn on.
Parallel to
ground
More than
40°
3
USER’S GUIDE 2534/2654
Warning!
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
surprise or distract others around you.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down D for about two seconds to toggle the auto light
switch on (AUTO EL displayed) and off (AUTO EL not displayed).
• The auto light switch on indicator (AUTO EL) is on the display in all modes while the
auto light switch is turned on.
Charging Guide
After a full charge, timekeeping remains enabled for up to about nine months (Module
2534)/11 months (Module 2654), while the watch is used under the conditions
described below.
Operating Conditions
• Watch is not exposed to light
• Display on 18 hours per day, sleep state 6 hours per day
• 1 backlight operation (1.5 seconds) per day
• 10 seconds of alarm operation per day
• 1 countdown timer operation per day
Charge Times
Exposing the watch to light for the periods shown below each day restores the power
used by the above operating conditions.
Exposure Level (Brightness)
Approximate Exposure Time
Outdoor Sunlight (50,000 lux)
5 minutes
Battery
Sunlight Through a Window (10,000 lux)
24 minutes
This watch is equipped with a solar cell and a rechargeable battery (secondary
battery) that is charged by the electrical power produced by the solar cell. The
illustration shown below shows how you should position the watch for charging.
Daylight Through a Window on a Cloudy Day
(5,000 lux)
48 minutes
Indoor Fluorescent Lighting (500 lux)
8 hours
Solar cell
Example: Orient the watch so its
face is pointing at a light source.
• Note that charging efficiency drops
when any part of the solar cell is
blocked by clothing, etc.
• The illustration shows how to position
a watch with a resin band.
Recovery Times
The table below shows the amount exposure that is required to take the battery from
one level to the next.
Exposure Level
(Brightness)
Level
Battery Power
Indicator
All functions enabled.
2
All functions enabled.
3
All functions enabled.
4
5
Beeper tone, backlight,
display, and buttons are
(Charge Soon Alert) disabled.
All functions, including
timekeeping, are disabled.
• The flashing
indicator at Level 4 tells you that battery power is very low, and that
exposure to bright light for charging is required as soon as possible.
• At Level 5, all functions are disabled and settings return to their initial factory
defaults. Functions are enabled once again after the rechargeable battery is
charged, but you need to set the current time, date, and all other settings after the
battery is recharged to Level 3 from Level 5. Though the time appears on the display
after the battery is charged to Level 4, you will not be able to change the time setting
until the battery reaches Level 3.
• Leaving the watch in direct sunlight or some other very strong light source can
cause the battery power indicator to temporarily show a reading that is higher than
the actual battery level. The correct battery power indicator should appear after a
few minutes.
• If you use the backlight or any of the alarm functions a number of times during a
short period, RECOVER appears on the display and the following operations
become disabled until battery power recovers.
Backlight
Beeper tone
After some time, battery power will recover and RECOVER will disappear, indicating
that the above functions are enabled again.
Charging Precautions
Certain charging conditions can cause the watch to become very hot. Avoid leaving
the watch in the areas described below whenever charging its rechargeable battery.
Also note that allowing the watch to become very hot can cause its liquid crystal
display to black out. The appearance of the LCD should become normal again when
the watch returns to a lower temperature.
Level 1
4 hours
98 hours (Module 2534)
19 hours
67 hours (Module 2654)
7 hours (Module 2534)
6 hours (Module 2654)
–––
Indoor Fluorescent Lighting
–––
60 hours
(500 lux)
• The above exposure time values are all for reference only. Actual required exposure
times depend on lighting conditions.
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Power Saving Function
When turned on, the Power Saving function automatically
puts the watch into a sleep state whenever it is left in an
area where it is dark for 30 to 35 minutes. The sleep state
is indicated by a blank screen with SLEEP flashing on it.
In the sleep state, all functions are enabled, except for the
display.
• Wearing watch inside the sleeve of clothing can cause it
to enter the sleep state.
Function Status
1
Level 2
▲
The battery power indicator on the display shows you the current status of the
rechargeable battery’s power.
Level 3
65 minutes (Module 2534) 18 hours (Module2534)
4 hours
1 hour (Module 2654) 14 hours (Module 2654)
Sunlight Through a
Window(10,000 lux)
Daylight Through a Window
on a Cloudy Day (5,000 lux)
Level 4
▲
Battery Power Indicator
Outdoor Sunlight
(50,000 lux)
Approximate Exposure Time
Level 5
▲
Important!
• Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause rechargeable battery
power to run down. Be sure that the watch is normally exposed to bright light
whenever possible.
• This watch employs a solar cell that converts light into electricity, which charges a
built-in rechargeable battery. Normally, the rechargeable battery should not need
replacement, but after very long use over a number of years, the rechargeable
battery may lose its ability to achieve a full charge. Should you notice problems with
getting the rechargeable battery to a full charge, contact your dealer or CASIO
distributor about having the rechargeable battery replaced.
• The rechargeable battery should be replaced with a CASIO-specified CTL1616
battery only. Other rechargeable batteries can cause damage to the watch.
• All data stored in memory is deleted, and the current time and all other settings
return to their initial factory defaults whenever battery power drops to Level 5 and
when you have the battery replaced.
• Turn on the watch’s Power Saving function and keep it in an area normally exposed
to bright light when storing it for long periods. This helps to keep the rechargeable
battery from going dead.
Battery power indicator
• Stable operation is promoted by frequent charging.
To recover from the sleep state
Perform any one of the following operations.
• Move the watch to a well-lit area. It can take up to five seconds for the display to turn
on.
• Press any button.
• Angle the watch towards your face for reading.
To turn Power Saving on and off
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C seven times until the Power Saving on/off
screen appears.
3. Press D to toggle Power Saving on (ON) and off
(OFF).
4. Press A to exit the setting screen.
• The Power Saving on indicator (SAVE) is on the display
in all modes while the Power Saving is turned on.
Auto Return Feature
If you leave a screen with flashing digits on the display for two or three minutes without
performing any operation, the watch automatically saves any settings you have made
up to that point and exits the setting screen.
Initial Screens
When you enter the Telememo, World Time, or Alarm Mode, the data you were
viewing when you last exited the mode appears first.
Data and Setting Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Warning!
Leaving the watch in bright light to charge its rechargeable battery can cause it
to become quite hot. Take care when handling the watch to avoid burn injury.
The watch can become particularly hot when exposed to the following
conditions for long periods.
• On the dashboard of a car parked in direct sunlight
• Too close to an incandescent lamp
• Under direct sunlight
4
USER’S GUIDE 2534/2654
Timekeeping
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The year can be set in the range of 2000 to 2039.
• The watch’s built-in full automatic calendar automatically makes allowances for
different month lengths and leap years. Once you set the date, there should be no
reason to change it except when battery power drops to Level 5.
World Time
• The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
• The GMT differential is the time difference between the time zone where the city is
located and Greenwich Mean Time.
• GMT differential is calculated by this watch based on Universal Time Coordinated
(UTC) data.
Backlight Precautions
• The electro-luminescent panel that provides illumination loses power after very long
use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• The backlight automatically turns off whenever an alarm sounds.
• Frequent use of the backlight runs down the battery.
Auto light switch precautions
• Wearing the watch on the inside of your wrist and movement or vibration of your arm
can cause the auto light switch to activate and illuminate the display. To avoid
running down the battery, turn off the auto light switch whenever engaging in
activities that might cause frequent illumination of the display.
More than 15 degrees
too high
• The backlight may not light if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• The backlight turns off in about one second, even if you
keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with
proper operation of the auto light switch. If the backlight
does not light, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back
toward you again. If this does not work, drop your arm
all the way down so it hangs at your side, and then bring
it back up again.
• Under certain conditions, the backlight may not light until
about one second after you turn the face of the watch
towards you. This does not necessarily indicate
malfunction of the backlight.
• You may notice a very faint clicking sound coming from
the watch when it is shaken back and forth. This sound
is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
City Code Table
City
Code
–––
HNL
ANC
LAX
DEN
CHI
NYC
CCS
RIO
–––
–––
GMT
LON
PAR
City
HONOLULU
ANCHORAGE
LOS ANGELES
DENVER
CHICAGO
NEW YORK
CARACAS
RIO DE JANEIRO
LONDON
GMT
Other major cities in same time zone
Differential
–11.0
PAGO PAGO
–10.0
PAPEETE
–09.0
NOME
SAN FRANCISCO, LAS VEGAS, VANCOUVER,
–08.0
SEATTLE, DAWSON CITY
–07.0
EL PASO, EDMONTON
HOUSTON, DALLAS/FORT WORTH, NEW ORLEANS,
–06.0
MEXICO CITY, WINNIPEG
MONTREAL, DETROIT, MIAMI, BOSTON, PANAMA CITY,
–05.0
HAVANA, LIMA, BOGOTA
–04.0
LA PAZ, SANTIAGO, PORT OF SPAIN
SAO PAULO, BUENOS AIRES, BRASILIA,
–03.0
MONTEVIDEO
–02.0
–01.0
PRAIA
DUBLIN, LISBON, CASABLANCA, DAKAR, ABIDJAN
+00.0
PARIS
+01.0
CAI
JRS
JED
CAIRO
JERUSALEM
+02.0
JEDDAH
+03.0
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
HKG
TEHRAN
DUBAI
KABUL
KARACHI
DELHI
DHAKA
YANGON
BANGKOK
HONG KONG
+03.5
+04.0
+04.5
+05.0
+05.5
+06.0
+06.5
+07.0
+08.0
TYO
ADL
SYD
NOU
WLG
TOKYO
ADELAIDE
SYDNEY
NOUMEA
WELLINGTON
+09.0
+09.5
+10.0
+11.0
+12.0
MILAN, ROME, MADRID, AMSTERDAM, ALGIERS,
HAMBURG, FRANKFURT, VIENNA, STOCKHOLM,
BERLIN
ATHENS, HELSINKI, ISTANBUL, BEIRUT, DAMASCUS,
CAPE TOWN
KUWAIT, RIYADH, ADEN, ADDIS ABABA, NAIROBI,
MOSCOW
SHIRAZ
ABU DHABI, MUSCAT
MALE
MUMBAI, KOLKATA
COLOMBO
JAKARTA, PHNOM PENH, HANOI, VIENTIANE
SINGAPORE, KUALA LUMPUR, BEIJING, TAIPEI,
MANILA, PERTH, ULAANBAATAR
SEOUL, PYONGYANG
DARWIN
MELBOURNE, GUAM, RABAUL
PORT VILA
CHRISTCHURCH, NADI, NAURU ISLAND
• Based on data as of June 2002.
Sort Table
1
2
3
4
5
6
7
8
9
(space)
A
B
C
D
E
F
G
H
10
11
12
13
14
15
16
17
18
I
J
K
L
M
N
O
P
Q
19
20
21
22
23
24
25
26
27
R
S
T
U
V
W
X
Y
Z
28
29
30
31
32
33
34
35
36
0
1
2
3
4
5
6
7
8
37
38
39
40
41
9
.
:
/
5