Char-Broil LP Gas Grill User's Manual

Add to my manuals
32 Pages

advertisement

Char-Broil LP Gas Grill User's Manual | Manualzz

K E E P E R S O F T H E F L A M E

L P Gas Grill Use and Care

For Outdoor Use Only

To installer or person assembling grill: Leave this manual with grill for future reference.

To consumer: Keep this manual for future reference.

This manual applies to a variety of grill styles. Your grill will not have all of the features shown.

WARNING

Read this manual before cooking on grill. Failure to follow all manufacturers’ instructions could result in serious personal injury and/or property damage.

Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

Printed in USA 2005 Generic U & C_E • 4165451 (01-31-05) 2

2

WARNING

FOR YOUR SAFETY

1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

2. An LP tank not connected for use shall not be stored in the vicinity of this or any other appliance.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, immediately call your gas supplier or your fire department.

Call Grill Service Center For Help And Parts

If you need help or warranty parts please call

1-800-241-7548.

• Business hours:

Open 24 hours - Seven days a week

• To order non-warranty replacement parts or accessories (grill cover, cleaners, paint) call

1-800-993-2677 or send a FAX to

1-706-565-2121.

• Visit us on the web at: www.charbroil.com

Attach receipt here:

CAUTION

For residential use only. Do not use for commercial cooking.

Installation Safety Precautions

• Use grill only with LP (propane) gas and the regulator/valve assembly supplied.

• Grill installation must conform with local codes, or in their absence with National Fuel Gas Code, NFPA

54 / ANSI Z223.1 or CAN/CGA-B149.2 Propane

Installation Code.

Handling and storage of LP cylinders must conform to LP Gas Code

NFPA/ANSI 58.

Grill is not for use in or on recreational vehicles and/or boats.

• All electrical accessories (such as rotisserie) must be electrically grounded in accordance with local codes, or National Electrical Code, ANSI / NFPA

70 or Canadian Electrical Code, CSA C22.1.

Keep any electrical cords and/or fuel supply hoses away from any hot surfaces.

• This grill is safety certified for outdoor use in the

United States and/or Canada only. Do not modify for use in any other location. Modification will result in a safety hazard.

To insure your satisfaction and for follow-up service, register your grill online at:

www.grillregistration.com

Important:

Fill out Warranty information below

Warranty Information

Model Number

Serial Number

See rating label on grill for serial number.

Date Purchased

WARNING

CARBON MONOXIDE HAZARD

Burning charcoal releases carbon monoxide, which has no odor and can cause serious injury or death. Never burn charcoal inside homes, vehicles or tents.

Table of Contents

For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Call Grill Service Center For Help and Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Fill Out Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Safety Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Warranty’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

LP Tank Removal, Transport and Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

LP Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

LP (Liquefied Petroleum Gas) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

LP Tank Filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

LP Tank Exchange. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

LP Tank Leak Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Connecting Regulator To The LP Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 7

Safety Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Leak Testing Valves, Hoses and Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Valve Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Hose Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Turning Grill Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Ignitor Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

For Safe Use Of Your Grill and To Avoid Serious Injury. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Ignitor Lighting and Match Lighting Traditional Series, QuickSet and QuickSet Traditional . . . . . . . . . . . . . . . 9

Ignitor Lighting and Match Lighting Performance and Advantage Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Sideburner Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Rotisserie Burner Ignitor and Match Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Sideburner Ignitor and Match Lighting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Burner Flame Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Before Your First Cookout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Cleaning The Traditional Series, QuickSet and QuickSet Traditional Burner Assembly . . . . . . . . . . . . . . . . . . 12, 13

Cleaning The Performance and Advantage Burner Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 15

Cleaning The Rotisserie Burner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Rotisserie Burner Use, Cooking Chart and Cooking Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

General Grill Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Care And Cleaning Of Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Natural Hazard Spiders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Charcoal/Gas Grills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Cooking Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Food Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

How To Tell If Meat Is Grilled Throughly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Storing Your Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24, 25

Troubleshooting - Electronic Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Recipes by Chef Christopher Koetke, CEC, CCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Recipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 www.grillregistration.com . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3

4

Safety Symbols

The symbols and boxes shown below explain what each heading means. Read and follow all of the messages found throughout the manual.

DANGER

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION: Indicates a potentially hazardous situation or unsafe practice which, if not avoided, may result in minor or moderate injury.

Warranty

Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning with the date of purchase.

Castings - Limited Lifetime

All Burner - 3 years

Electronic ignition (excluding battery) - 3 years

Remaining parts (excluding battery) - 1 year

This limited warranty is for replacement of defective parts only.

Manufacturer will not be responsible for failure or damage resulting from use, accident, alteration, misuse, transportation, commercial use, abuse, hostile environments, improper installation or installation not in accordance with local codes.

Manufacturer will, at its option, refinish or replace any product or part found to be defective during its respective warranty period.

Manufacturer will require return of the part(s) claimed to be defective, for its inspection, freight or postage prepaid.

Manufacturer may require reasonable proof of purchase and suggests that receipts be retained.

This limited warranty does not cover scratches, dents, corrosion or discoloring by heat, abrasive and chemical cleaners or any tools used in the assembly or installation of the appliance.

This limited warranty does not cover surface rust, or the discoloration of stainless steel surfaces.

This limited warranty does not include the cost of any inconvenience, personal injury or property damage due to failure of the product.

THIS EXPRESS WARRANTY IS THE SOLE WARRANTY

GIVEN BY THE MANUFACTURER AND IS IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR

A PARTICULAR PURPOSE OR USE.

Neither dealers nor the retail establishment selling this product has any authority to make any additional warranties or to promise remedies in addition to or inconsistent with those stated above.

Manufacturer’s maximum liability, in any event, shall not exceed the purchase price of the product paid by the original consumerpurchaser.

NOTE: Some states do not allow an exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This limited warranty gives you specific legal rights as set forth herein. You may also have other rights which vary from state to state. In the state of California only, if refinishing or replacement of the product is not commercially practicable, the retailer selling this product or the Manufacturer will refund the purchase price paid for the product, less the amount directly attributable to use by the original consumer-purchaser prior to discovery of the nonconformity. In addition, in the state of

California only, you may take the product to the retail establishment selling this product in order to obtain performance under this limited warranty.

If you wish to obtain performance of any obligation under this limited warranty, you should write to:

Consumer Warranty / P.O. Box 1240

Columbus, GA 31902-1240

DANGER

• Never fill the cylinder beyond 80% full. An overfilled

LP tank is hazardous due to possible gas released from the safety relief valve.

• The safety relief valve on the LP tank could activate releasing gas and cause an intense fire with risk of property damage, serious injury or death.

• NEVER store a spare LP tank under or near grill or in enclosed areas.

LP Tank Removal, Transport And Storage

• Turn OFF all control knobs and LP tank valve. Turn coupling nut counterclockwise by hand only - do not use tools to disconnect. Remove attachment holding LP tank, then lift up and off support bracket.

Install safety cap onto LP tank valve. Always use cap and strap supplied with valve. Failure to use safety cap as directed may result in serious personal injury and/or property damage.

LP Tank Valve

Safety Cap

• If you see, smell or hear escaping gas, immediately get away from the LP tank/grill and call your fire department.

• All spare LP tanks must have safety caps installed on the LP tank outlet.

Retainer Strap

• A disconnected LP tank in storage or being transported must have a safety cap installed (as shown). Do not store an LP tank in enclosed spaces such as a carport, garage, porch, covered patio or other building. Never leave an LP tank inside a vehicle which may become overheated by the sun. Always keep LP tank in upright position during use, transit or storage.

• Do not store an LP tank in an area where children play.

LP Tank

• The LP tank used with your grill must meet the following requirements:

• Use LP tanks only with these required measurements: 12" (30.5cm) (diameter) x 18" (45.7

cm) (tall) with 20 lb. (9 kg.) capacity maximum.

• LP tanks must be constructed and marked in accordance with specifications for LP tank of the

U.S. Department of Transportation (DOT) or for

Canada, CAN/CSA-B339, cylinders, spheres and tubes for transportation of dangerous goods.

Transport Canada (TC). See LP tank collar for marking.

• LP tank valve must have:

• Type 1 outlet compatible with regulator or grill.

• Safety relief valve.

• UL listed Overfill Protection Device

(OPD). This OPD safety feature is identified by a unique triangular hand wheel.

Use only LP tanks equipped with this type of valve.

OPD Hand Wheel

• LP tank must be arranged for vapor withdrawal and include collar to protect LP tank valve.

5

LP (Liquefied Petroleum Gas)

• LP gas is nontoxic, odorless and colorless when produced.

For Your Safety , LP gas has been given an odor (similar to rotten cabbage) so that it can be smelled.

• LP gas is highly flammable and may ignite unexpectedly when mixed with air.

• Use a clean paint brush and a 50/50 soap and water solution.

Use mild soap and water.

s

Do not use household cleaning agents.

Damage to gas train components can result.

Brush soapy solution onto areas indicated by arrows.

LP Tank Filling

• Use only licensed and experienced dealers.

• LP dealer must purge a new tank before filling.

• Dealer should NEVER fill LP tank more than 80% of

LP tank volume. Volume of propane in tank will vary by temperature.

• A frosty regulator indicates gas overfill. Immediately close LP tank valve and call local LP gas dealer for assistance.

• Do not release liquid propane (LP) gas into the atmosphere. This is a hazardous practice.

• To remove gas from LP tank, contact an LP dealer or call a local fire department for assistance. Check the telephone directory under “Gas Companies” for nearest certified LP dealers.

WARNING

If “growing” bubbles appear do not use or move the LP tank. Contact an LP gas supplier or your fire department!

6

LP Tank Exchange

• Many retailers that sell grills offer you the option of replacing your empty LP tank through an exchange service. Use only those reputable exchange companies that inspect, precision fill, test and certify their cylinders.

Exchange your tank only for an

OPD safety feature-equipped tank as described in the "LP Tank" section of this manual.

• Always keep new and exchanged LP tanks in upright position during use, transit or storage.

• Leak test new and exchanged LP tanks BEFORE connecting to grill.

Connecting Regulator To The LP Tank

1.

LP tank must be properly secured onto grill. (Refer to Assembly Manual)

2.

Turn all control knobs including sideburner (if featured) to the OFF position.

3.

Turn LP tank OFF by turning hand-wheel clockwise to a full stop .

4.

Remove the protective cap from LP tank valve.

Always use cap and strap supplied with valve.

Off

Clockwise

LP Tank Leak Test

For your safety

• Leak test must be repeated each time LP tank is exchanged or refilled.

• Do not smoke during leak test.

• Do not use an open flame to check for gas leaks.

• Grill must be leak tested outdoors in a wellventilated area, away from ignition sources such as gas fired or electrical appliances. During leak test, keep grill away from open flames or sparks.

Safety Relief Valve

Strap and Cap

OPD Hand Wheel

Type 1 outlet with thread on outside

Do not use a POL transport plug

(plastic part with external threads)!

It will defeat the safety feature of the valve.

5. Hold regulator and insert nipple into LP tank valve.

Hand-tighten the coupling nut, holding regulator in a straight line with LP tank valve so as to not crossthread the connection.

DANGER

• Do not insert any tool or foreign objects into the valve outlet or safety relief valve. You may damage the valve and cause a leak. Leaking propane may result in explosion, fire, severe personal injury, or death.

• If a leak is detected at any time, STOP and call the fire department.

• If you cannot stop a gas leak, immediately close LP tank valve and call LP gas supplier or your fire department!

Nipple has to be centered into the LP tank valve.

WARNING

• Never attempt to attach this grill to the selfcontained LP gas system of a camper trailer or motor home.

• Do not use grill until leak-tested.

Straight

Hold coupling nut and regulator as shown for proper connection to LP tank valve.

6.

Turn the coupling nut clockwise and tighten to a full solid stop. The regulator will seal on the backcheck feature in the LP tank valve, resulting in some resistance.

An additional one-half to threequarters turn is required to complete the connection. Tighten by hand only – do not use tools.

NOTE:

If you cannot complete the connection, disconnect regulator and repeat steps 5 and 6. If you are still unable to complete the connection, do not use this regulator!

Safety Tips s Before opening LP tank valve, check the coupling nut for tightness.

s

When grill is not in use, turn off all control knobs and LP tank valve.

s s

Never move grill while in operation or still hot.

Use long-handled barbecue utensils and oven mitts to avoid burns and splatters.

s

Maximum load for sideburner and side shelf is

10 lbs.

s Do not use a cooking pot larger than 9” on the sideburner.

s

A soup can or grease cup must be attached to grease clip/grease tray and emptied after each use. Do not remove soup can/grease cup until grill has completely cooled.

s If you notice grease or other hot material dripping from grill onto valve, hose or regulator, turn off gas supply at once. Determine the cause, correct it, then clean and inspect valve, hose and regulator before continuing. Perform a leak test.

s

The regulator may make a humming or whistling noise during operation. This will not affect safety or use of grill.

s

If you have a grill problem see the

"Troubleshooting Section" .

7

Leak Testing Valves, Hose and Regulator

1. Turn all grill control knob(s) to OFF.

2.

Be sure regulator is tightly connected to LP tank.

3.

Completely open LP tank valve by turning hand wheel counterclockwise. If you hear a rushing sound , turn gas off immediately. There is a major leak at the connection.

Correct before proceeding .

4.

Brush soapy solution onto areas where bubbles are shown :

Sideburner Hose

(if featured)

WARNING

• If the regulator frosts turn off grill and LP tank valve immediately. This indicates a problem with the tank and it should not be used on any product. Return to supplier!

Valve Check

• Important: Make sure gas is OFF at LP tank before checking valves . Knobs lock in OFF position. To check valves, first push in knobs and release, knobs should spring back. If knobs do not spring back, replace valve assembly before using grill. Turn knobs to LOW position then turn back to

OFF position. Valves should turn smoothly.

Hose Check

• Before each use, check to see if hoses are cut, worn or kinked. Replace damaged hoses before using grill. Use only valve/hose/regulator specified by manufacturer.

s Never remove opening at end of valve.

HeatWave Hose

(if featured)

Normal

Hose

Kinked

Hose

Sideburner

Valve

5. If “growing” connections.

bubbles appear, there is a leak.

Close LP tank valve immediately and re-tighten

If leaks cannot be stopped “do not try to repair” call for replacement parts. Order new parts by giving the serial number, model number and name of items needed to the Grill

Service Center at 1-800-241-7548.

8

6.

Always close LP tank valve after performing leak test by turning hand wheel clockwise.

Turning Grill Off

• Turn all knobs to OFF position. Turn LP tank OFF by turning hand-wheel clockwise to a full stop.

Ignitor Check

• Turn gas off at LP tank.

Press ignitor button or turn ignitor knob rapidly. "Click" should be heard and spark seen each time between collector box or burner and electrode. See click or spark.

"Troubleshooting" if no

WARNING

For Safe Use Of Your Grill And To Avoid

Serious Injury:

• Do not let children operate or play near grill.

• Keep grill area clear and free from materials that burn.

• Do not block holes in bottom or back of grill.

• Check burner flames regularly.

• Usegrillonlyinwell-ventilatedspace.NEVERusein

enclosedspacesuchascarport,garage,porch, coveredpatio,orunderanoverheadstructureofany kind.

• Donotusecharcoalorceramicbriquetsinagasgrill.

(Unlessbriquetsaresuppliedwithyourgrill).

• Usegrillatleast3ft.from

anywallorsurface.

Maintain10ft.clearance

toobjectsthatcancatch fireorsourcesofignition suchaspilotlightsonwater heaters,liveelectricalappliances,etc.

• ApartmentDwellers:

Check with management to learn the requirements and fire codes for using an LP gas grill in your apartment complex. If allowed, use outside on the ground floor with a three (3) foot clearance from walls or rails. Do not use on or under balconies.

• NEVER attempt to light burner with lid closed.

A buildup of non-ignited gas inside a closed grill is hazardous.

• Never operate grill with LP tank out of correct position specified in assembly instructions.

• Always close LP tank valve and remove coupling nut before moving LP tank from specified operation position.

Ignitor Lighting Traditions Series, QuickSet and QuickSet Traditional s

Do not lean over grill while lighting.

1. Open lid during lighting.

Turn on gas at LP tank.

2.

3.

Turn LEFT knob to IGNITE.

Push Piezo Ignitor Button rapidly, or hold

Electronic Ignition, or turn Rotary Ignitor

Knob (up to 5 times) to light. Be sure burner lights and stays lit.

4.

5.

6.

If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure.

To ignite right burner, turn right knob to .

If IGNITOR does not work, follow match lighting instructions.

After Lighting: Turn knobs to HI position for warm-up.

Do not warm up grill with knobs on IGNITE. Knobs and handle will become uncomfortably hot if left in

IGNITE positions.

Match Lighting Traditions Series, QuickSet and

QuickSet Traditional s

Do not lean over grill while lighting.

1. Open lid.

Turn on gas at LP tank.

2.

Place lit match into match lighting hole from outside grill bottom (as shown).

3.

Push in and turn RIGHT knob to IGNITE. Be sure burner lights and stays lit.

4.

Light left burner by pushing LEFT knob in and turning to IGNITE.

After Lighting: Turn knobs to HI for warm-up.

Match-lighting hole is in bottom or side

9

10

Ignitor Lighting:

Performance and Advantage Series

Two Burner Grill: s Do not lean over grill while lighting.

1. Open lid.

Turn on gas at LP tank.

2.

3.

Turn left knob to .

4.

5.

Push and hold Electronic Ignitor button.

If ignition does NOT occur in 5 seconds, turn the burner controls off, wait 5 minutes and repeat the lighting procedure.

To ignite right burner, turn right knob to .

Match Lighting for Four Burner Grills s Do not lean over grill while lighting.

1. Open lid.

Turn on gas at LP tank.

2.

Place lit match into match lighting hole from outside of grill bottom (as shown).

3.

Push in and turn right knob to . Be sure burner lights and stays lit. Push in right-center burner to light, left center and left burner.

Three Burner Grill: s Do not lean over grill while lighting.

1. Open lid . Turn on gas at LP tank.

2.

3.

Turn left knob to .

Push and hold Electronic Ignitor button.

4.

5.

If ignition does NOT occur in 5 seconds, turn the burner controls off, wait 5 minutes and repeat the lighting procedure.

Ignite center burner by turning center knob to , then ignite right burner by turning right knob to .

Four Burner Grill: s

Do not lean over grill while lighting.

1. Open lid.

Turn on gas at LP tank.

2.

3.

Turn left knob to .

Push and hold Electronic Ignitor button.

4.

5.

If ignition does NOT occur in 5 seconds, turn the burner controls off, wait 5 minutes and repeat the lighting procedure.

Ignite left-center burner by turning left-center knob to , then ignite right-center burner by turning right-center knob to , then ignite right burner by turning right knob to .

Match Lighting for Two and Three Burner Grills s

Do not lean over grill while lighting.

1. Open lid . Turn on gas at LP tank.

2. Match holder is on the right rear leg.

Attach match to match holder, light match.

Place match into match lighting hole from outside of grill bottom (as shown).

3. Push in and turn right knob to . Be sure burner lights and stays lit.

4. Two burner grills, push in and turn left knob to .

Three burner grill, push in and turn center knob to and then right knob to .

Match holder for two and three burner grills

Match-lighting hole is on side of grill bottom

CAUTION

If burner does not light, turn knob(s) to OFF wait 5 minutes, try again. If the burner does

, not ignite with the valve open, gas will continue to flow out of the burner and could accidentally ignite with risk of injury.

• Sideburner Use on grid .

Remove grid from sideburner before using griddle.

Never exceed griddle zone value setting shown on graphics. Damage to Teflan® may occur. Do not close lid when using griddle.

Grid

Griddle

Rotisserie Burner Ignitor Lighting

1.

Turn all knobs to OFF.

2 .

Open lid during lighting.

Turn gas on at LP

3.

4.

5.

Tank.

Push in and turn Burner Selector Knob to ON

ROTISSERIE BURNER.

Press Piezo Ignitor Button or Electronic

Ignition hold up to 5 seconds. Or turn Rotary

Ignitor Knob rapidly (up to 5 times). Be sure burner lights and stays lit.

If IGNITOR does not work, follow match lighting instructions above.

Match Lighting

1. Open lid.

Turn on gas at LP tank.

2.

Place lit match near porthole of burner.

3.

Push in and turn Burner Selector Knob to

ON ROTISSERIE BURNER. Be sure burner lights and stays lit.

Burner Flame Check

• Light burner, rotate knob(s) from HIGH to LOW. You should see a smaller flame in LOW position than seen on HIGH. Always check flame prior to each use. Perform flame check on sideburner (if equipped). If only low flame is seen refer to

"Sudden drop or low flame" in the Troubleshooting

Section .

HIGH

LOW

To match light use first opening in burner

Note: Rotisserie burner and main burner cannot be used at the same time.

Sideburner Ignitor Lighting

1.

2.

Turn gas on at LP tank.

Push in and turn knob to HIGH .

3.

4.

Turn or push (up to 5 times to light burner). Be sure burner lights and stays lit.

If burner does not light turn knob(s) to OFF, wait 5 minutes, try again.

Match Lighting

1.

Turn gas on at LP tank.

2.

Hold lit match to any port on the burner. Push in and turn sideburner knob to HIGH.

Be sure burner lights and stays lit.

Rotisserie burner only has one setting so flame cannot be checked.

Before Your First Cookout

• Light burners, check to make sure they are lit, close the lid and warm up grill on HI for 15 minutes.

Curing of paint and parts will produce an odor only on first lighting.

CAUTION

• Putting out grease fires by closing the lid is not possible. Grills are well ventilated for safety reasons.

• Do not use water on a grease fire. Personal injury may result. If a grease fire develops, turn knobs and LP tank off.

• Do not leave grill unattended while preheating or burning off food residue on HI.

If grill has not been regularly cleaned, a grease fire can occur that may damage the product.

11

12

Cleaning The Traditional Series, QuickSet and QuickSet Traditional Burner Assembly

Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting the grill.

1.

Turn gas off at control knobs and LP tank.

2.

Remove cooking grate and V-Bar.

3.

Under grill remove soup can, (unscrew ignitor button and remove battery on electronic ignition models), disconnect short ignitor wire (A) and clips from burner (B). To remove clips pull down on large end of clip attached to the valve, turn away from valve, rotate upward and remove small end of clip from burner tube.

4.

Inside grill remove burner assembly (C), clean ceramic portion of electrode with rubbing alcohol and a swab.

5.

Clean outside of burner with soap and water. Lay burner upside down on flat surface, insert garden hose to force water through tubes. Make sure water comes out of all burner holes. Open clogged holes with a thin wire. Shake out excess water and examine holes. Due to normal wear and corrosion some holes may become enlarged. If any large cracks or holes are found replace burner.

6.

If grill is to be stored, coat burner lightly with cooking oil. Wrap in protective cover to keep insects out.

7.

If not storing grill after cleaning, replace burner into grill bottom (C).

8.

To reattach clips hold large curved end away from burner tube, insert small curved end into hole under burner tubes, turn clip towards valve, snap into place.

VERY IMPORTANT: Clips must be attached correctly for proper grill function (B).

9.

Reattach ignitor wire to ignitor (A). (Reinstall battery and ignitor button on electronic ignition models.)

10. Reposition v-bar and cooking grate(s). Reattach clean can to grease clip.

11. Before cooking again on grill, perform a “Leak Test” and “Burner Flame Check” .

s Do not use ceramic briquets or charcoal unless a charcoal pan comes with your grill.

Clip

B

Valve

Burner Tube

QuickSet Burner

Electrode

C

A

Short Ignitor Wire

Remove button and battery on electronic ignition models

13

14

Cleaning The Performance and Advantage Burner Assembly

Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting the grill.

1.

Turn gas off at control knobs and LP tank.

2.

Remove cooking grids and vaporizer tents.

3.

Remove two pal nuts, carry-over tube and burners.

4.

Under grill remove grease pan and tray. Clean with soap and water.

5.

Disconnect battery and under console disengage ignitor wire.

6.

Wipe ceramic electrode with rubbing alcohol and cloth.

7.

Clean carry-over tube and burners exterior with soap and water. Lay burners on flat surface, insert garden hose (preferably with nozzle), into burner tubes forcing water through tubes. Make sure water comes out of every porthole. Open clogged portholes with a thin wire.

Shake out excess water and examine porthole. Due to normal wear and corrosion some portholes may become enlarged, if so replace burner. If any horizontal cracks appear from porthole to porthole or large holes (other than portholes) are found replace burner.

8.

If grill is to be stored, coat burners lightly with cooking oil. Wrap in protective cover to keep insects out.

If not storing use following steps.

VERY IMPORTANT: Burner tubes must engage valve openings as shown (A).

9.

Attach ignitor wire to electrode.

Replace battery.

10. Reposition cooking grids and vaporizer tents. Place clean grease tray and pan into grill bottom.

11. Before cooking again on grill, perform a “Leak Test” and “Burner Flame Check” .

s

Do not use ceramic briquets or charcoal in your grill.

Cleaning the Performance and Advantage Grease Tray

Performance and Advantage Series grills are equipped with a removable grease tray. Although grease will drain from the grease tray to the grease cup provided, food particles and debris may accumulate in the bottom and should be removed after cooking 5 to 10 times. This can easily be done by sliding the grease tray out of the rear of the unit. Make sure in replacing the tray to push it all the way forward.

CAUTION

• Handles close to the lid can become hot. Lift handle in the middle where it remains cool.

Vaporizer

Tents

Pal Nuts

Carry-Over Tube

Burner

Burner tubes correctly engaged in valves

A

Burner

Tube Valve

15

16

Cleaning The Rotisserie Burner

Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting the grill.

1.

Turn gas off at control knobs and LP tank.

2.

Disconnect ignitor wire from electrode (A).

3.

Remove thumbscrew from shield (B), remove shield and clean any accumulation of grease with soap and water.

4.

Unfasten hinge pins and hitch pin. Note how hinge pins and hitch pins are attached.

5.

Using a garden hose (preferably with nozzle), force water through burner tube. Make sure water

6.

Examine rotisserie housing and burner closely (C). If any cracks or large holes (other than portholes) are found replace rotisserie burner.

7.

Wipe ceramic portion of electrode (A) with rubbing alcohol and cloth.

8.

If grill is to be stored, coat burners lightly with cooking oil. Wrap in protective cover to keep insects out.

If not storing use following steps.

9.

After burner has been cleaned, place rotisserie burner onto back of grill bottom and attach with hinge pins and hitch pins.

10. Place gas tube inside burner tube, put shield over burner tube and secure with thumbscrew.

VERY IMPORTANT: Burner tubes must engage gas tube as shown (D).

11. Attach flat end of ignitor wire (A) to electrode.

Housing

Hinge Pin

Gas Tube

Shield

Thumbscrew

B

Burner Tube

Rotisserie Burner

A

BACK OF GRILL

Hitch Pin

Electrode

Hinge Pin

Hitch Pin

Ignitor Wire

D

C

Burner Portholes

Burner Tube

Gas Tube

Burner Tube

Rotisserie Burner Use

The rotisserie burner is a 10,500 BTU radiant heat burner that transforms your grill into a multilevel cooking center. It is attached to the back of the bottom casting, above the main grid.

You can use the burner as a broiler to cook foods on the cooking grates or bonus-grid. If you do, then you cannot use the bottom burner.

Or, you can remove the cooking grates or bonus grid, install a rotisserie and use the burner to perfectly roast foods on the split. This is the most common use for the burner. You cannot use the bottom burner with this process either.

By not using the lower burner, the grease and food drippings won’t burn and cause flare-ups. It’s healthier, it’s fuel-efficient, and it creates a delicious slow-cooked roast beef, chicken, or veggie kabob on the rotisserie...or a beautiful broiled salmon, lobster, or vegetable medley on the grid.

Cooking Chart For Rotisserie Burner

Item

Chicken/Fryer

Turkey Breast/

Bone-in

Cornish Hens

Duck

Pork Shoulder

Weight

3.5 lbs.

2.5 lbs.

Time

65 minutes

1 hr: 30 min.

20 oz.

4.5lbs.

3.25 lbs.

1 hr: 10 min.

2 hr: 15 min.

2 hr: 45 min.

Tips

0

Internal temperature 180 F

0

Internal temperature 180 F

Place pan of water in bottom of grill. Internal

Pork Boston Butt

Roast

Pork Tenderloin

3.3 lbs.

1.25 lbs.

2 hr: 45 min.

2.75 lbs.

Med: 40 min.

Well: 50 min.

1 hr: 30 min.

Pork Spareribs/

Beef Back Ribs

Beef Bottom

Round Roast

3.3 lbs.

Med rare: 1 hr 50 min.

Med: 2 hrs.

Well: 2 hrs: 10 min.

Place pan of water in bottom of grill. Internal

Place pan of water in bottom of grill.

0

Internal temperature: Med rare: 140 F

Cooking Tips

If you set a foil pan in the bottom casting, right on the burner, it will catch any food drippings created by cooking with the Rotisserie Burner. You’ll have no grease in the grill to clean.

• If you group different vegetables by the length of time it takes to cook, then everything will be done at the same time. Check the enclosed food chart for cooking times.

17

General Grill Cleaning

• Keep the outside of your grill looking new by cleaning it once a month with warm soap and water or a non-abrasive cleaner. If you don’t have a grill cover, wipe off dust and grime before starting your grill.

• Coating the cooking grids with spray-on cooking oil will keep the food from sticking and make clean up easier. After cooking, scrape the grates with a long handled, brass wire bristle brush.

• Check inside the grill bottom for grease build-up and clean often, especially after cooking fatty meat.

Repainting Your Grill

• After extended use and exposure to weather, paint on grill may change color slightly or become spotted. Although this detracts from grill’s appearance, it will not impair its performance.

• To refinish your grill brush outside of grill lid and bottom with wire brush and lightly sand with fine grit sandpaper. Sanding allows new paint to adhere more easily. Wash grill lid and bottom with soap and water to remove dust and grease. Do not use a grill cleaner on outside of grill. Wipe with vinegar.

Refinish outside with heat-resistant paint. Do not paint inside of grill.

• Do not mistake brown or black accumulation of grease and smoke for paint. Interiors of gas grills are not painted at the factory (and should never be painted) . Apply a strong solution of detergent and water or use a grill cleaner with scrub brush on insides of grill lid and bottom. Rinse and allow to completely air dry.

Do not apply a caustic grill/oven cleaner to painted surfaces.

•Vaporizer Tents: Will eventually decompose and weaken with use. Remove from grill and tap to loosen any scaling. Brush vigorously with a wire brush to remove any additional scaling, rust or residue.

• Plated wire grate(s): Wash grate(s) and V- bar with concentrated grill cleaner or use soap and water solution. Dry thoroughly and store indoors between cookouts.

• Plastic parts: wipe dry.

s

Wash with warm soapy water and

Do not use citrisol, abrasive cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.

• Porcelain grate(s): Because of glass-like composition, most residue can be wiped away with baking soda/water solution or specially formulated cleaner. Use non-abrasive scouring powder for stubborn stains.

18

Care And Cleaning Of Stainless Steel

Routine cleaning is necessary to preserve the appearance and corrosion resistance of Stainless Steel. The methods below are suggestions for cleaning stainless steel surfaces. Choose a cleaning method appropriate to the requirement. If you choose to use scouring powder or solvents, consult with the solvent manufacturer or supplier before use.

Before cleaning, first test any cleaning product in an inconspicuous location and consider the possibility of scratching and the potential for corrosion caused by not completely removing cleaners. Never use brushes or steel wool as they will scratch and leave particles embedded on stainless steel surfaces, which can lead to rusting. Always rub or wipe in the direction of the polish lines in the stainless steel surface, not across them. Thorough rinsing with clean water is recommended after all cleaning procedures. Dry all surfaces completely after rinsing. Be careful not to let any stainless steel cleaner come in contact with painted or plastic components as damage may occur.

Routine Care

The Char-Broil® Stainless Steel Grill Cleaner and the Thermos® Stainless Steel Grill Cleaner are good choices for routine cleaning of stainless steel surfaces. Mild stains and loose dirt and soil can also be removed with a soft cloth and clean warm water. Rinse with clean water and wipe dry.

Stubborn Stains

Stubborn stains, discoloration and possibly rust and rust pitting can occur from cooking, exposure to harsh outdoor conditions, or extreme cooking temperatures. There are many cleaning agents commercially available formulated to restore the finish of stainless steel. Obtain advice from the solvent manufacturer or supplier when choosing the appropriate cleaner for your requirement. These cleaners can be acidic. Care should be taken to avoid contact with eyes or mouth. Be careful not let any powder or solvent come in contact with painted or plastic components as damage may occur.

The chart below has been reproduced with permission from the Specialty Steel Institute of North America. For additional details regarding the care and cleaning of stainless steel, visit their website at www.ssina.com for more information. For the latest new products for the care and cleaning of stainless steel go to www.charbroil.com.

Job

Routine Cleaning

Cleaning Agents*

Warm Water, Soap, Ammonia, Detergent

Comments

Apply with sponge or soft cloth.

Can be used on all finishes.

Fingerprints and Smears 3M Stainless Steel Cleaner and Polish, Arcal 20, Lac-O-Nu,

Lumin Wash, O’Cedar Cream Polish, Stainless Shine

Stubborn Stains and Discoloration

3M Stainless Steel Cleaner and Polish, All chem Concentrated

Cleaner, Samae, Twinkle, Cameo Copper Cleaner, Grade FFF or Grade F Italian Pumice, Whiting or Talc, Liquid Nu Steel,

Copper’s or Revere Stainless Steel Cleaner, Household

Cleaners, Lumin Cleaner, Zud Restoro, Sta-Clean, Highlite,

Allen Polish, Penny-Brite, Copper-Brite

Provides barrier film to minimize fingerprints. Can be used on all finishes.

Rub lightly, using dry damp cloth, in the direction of polish lines on the stainless steel.

Grease and Blood

Burnt-on or

Baked-on Foods

Scotch-Brite Power Pad 2001, Easy-Off, De-Grease-It, 4% to

6% hot solution of such agents as tri-sodium polyphosphate,

5% to 15% caustic soda solution

Excellent removal on acids, all finishes.

Particularly useful where rubbing is not practical.

Grease and Oil Any good commercial detergent or caustic cleanser.

Apply with sponge or soft cloth in direction of polish lines.

*NOTE: Use of proprietary names is intended only to indicate a type of cleaner and does not constitute an endorsement. Omission of any proprietary cleanser does not imply its inadequacy. All products should be used in strict accordance with instructions on package.

19

CAUTION

NATURAL HAZARD • SPIDERS

FACT: Sometimes spiders and other small insects climb into the burner tubes attached to the burner. The spiders spin webs, build nests and lay eggs. The webs or nests can be very small, but they are very strong and can block the flow of gas. Clean burner(s) prior to use after storing, at the beginning of grilling season or after a period of one month not being used.

Typical spider webs inside burner

Spider Guards are on the air intakes in an effort to reduce this problem, but it will not eliminate it! An obstruction can result in a “flashback” (a fire in the burner tubes). The grill may still light, but the obstruction does not allow full gas flow to the burner(s).

IF YOU EXPERIENCE THE FOLLOWING:

1.

Smell gas.

2.

3.

4.

Burner(s) will not light.

A small yellow flame from burner

(should be blue).

Fire coming from around or behind a control knob.

STOP!

Immediately turn off gas at LP tank.

s

After a venturi fire you must inspect the hose and do a “Leak Test” to assure no damage has occurred to the parts.

20

SOLUTION: Wait for grill to cool.

Follow the cleaning instructions for your appropriate grill. Clean burners often.

Spiders and insects don’t care if your grill is brand new or you just cleaned it.

We have found in trying to remove web’s from the burner tubes a 12” pipe cleaner cleans out the tubes, or water from a hose with a nozzle attached.

Forced water is needed to wash out the web.

Charcoal/Gas Grills

If you haven’t attached the handles to the grate follow step 1.

.

Step 1.

Left handle is shown in the correct position between second and third wire from end. Hook end of right handle over back and pull to hook over front wire.

Handle in correct position

Grate support wires

Warming Rack

Remove cooking grate(s) and hang on back of grill using the hanger wire.

Remove V-bar and place two pan supports into grill bottom.

• Remove warming rack from leg wire and straight wire.

• Rotate leg wire toward back of grill bottom.

• Place charcoal tray on pan supports.

• Rotate grate support wires in the tray into upright positions.

• Fill charcoal tray with one layer of charcoal briquettes.

• Place warming rack in the upper position on the wire grate supports.

V-Bar

Pan Support

s Use oven mitts during cooking.

Grill Series: 7000 & 8000 QuickSet Traditional

• Follow standard lighting instructions to light the grill.

• Turn both control knobs to “HI” position.

• Close lid and wait 10 minutes.

• Open lid and continue to heat for 5 to 10 minutes.

• Turn control knobs to “OFF” position.

• Let charcoal briquettes continue to whiten for 10 to 15 minutes.

WARNING

s

Make sure ashes are cool and there are no hot embers prior to storing your grill. Do not store grill until coals are cold.

s

Use only enough charcoal to cover the bottom of the pan.

Grill Series 7000: 4 briquets wide by 10 long

Grill Series 8000: 5 briquets wide by 12 long s

Always light grill using gas. Never use lighter fluid, kerosene, gasoline or alcohol.

s

Burning charcoal produces carbon monoxide, a toxic odorless fume. Carbon monoxide accumulation may cause illness and/or death.

21

Cooking Chart

Cooking times and temperatures may vary according to specific recipes, cooking conditions or barbecue equipment used. Take these factors into consideration to insure best results. If you use the indirect cooking method (indirect cooking is lighting only one burner and placing food on opposite side of cooking grate), allow more grilling time.

Temperatures: High = 650°F / Medium = 450°F / Low = 300°F.

Cooking Time

22

Food

Beef

Hamburger 1/2” thick

Steak 1/2”

Roast

Pork

Chops 1/2”

Ribs 5-6 lbs.

Roast 3-5 lbs.

Ham Steak 1/2”

Ham 5 lb. fully cooked

Lamb

Chops 1/2”

Poultry

Chicken 2-1/2 to 3-1/2 lbs.

Chicken halved or quartered

Turkey

Seafood

Steaks 1” thick

Fillets 6-8 oz.

Shrimp large or jumbo

Venison

Steak 1” thick

Burgers 1/2”

Roast 3-4 lbs.

Vegetables

Baking Potato whole

Onions whole

Tomatoes half

Corn whole

Mushrooms

Setting

Medium

Medium-Hot

Low

Medium

Low-Medium

Low-Medium

Medium-Hot

Low-Medium

Medium

Low

Low

Low-Medium

Medium-Hot

Medium-Hot

Low-Medium

Medium

Medium

Low-Medium

Low

Low

Medium

Low

Medium

Med: 7-10 min. / Well done: 10-15 min.

Rare: 3-6 min. / Med: 6-9 min. / Well done: 9-12 min.

Rare: 18-22min. per lb. / Med: 22-28 min. per lb. / Well done: 28-32 min. per lb.

Well done: 15-20 min.

Well done: 45-90 min.

Well done: 18-23 min. per lb.

12-15 min.

20 min. per lb.

6-12 min.

1 hr., 15 min. to 1 hr., 30 min.

40-60 min.

18-20 min. per lb.

Well done: 10-25 min.

8-12 min.

8-12 min.

Rare: 8-10 min. / Med: 10-12 min.

Rare: 10-12 min. / Med: 12-15 min.

Rare: 20-22 min. per lb. / Med: 22-25 min. per lb.

Wrap vegetables in foil

55-60 min.

45 min.

30-40 min.

35-45 min.

15-20 min.

Food Safety

• Food safety is a very important part of enjoying the outdoor cooking experience. To keep food safe from harmful bacteria, follow these four basic steps:

Clean: Wash hands, utensils and surfaces with hot soapy water before and after handling raw meat and poultry.

Separate: Separate raw meats and poultry from ready-to-eat foods to avoid cross contamination. Use a clean platter and utensils when removing cooked foods.

Cook: Cook meat and poultry thoroughly to kill bacteria. Use a thermometer to ensure proper internal food temperatures.

Chill: Refrigerate prepared foods and leftovers promptly.

For more information call: USDA Meat and Poultry Hotline at

1-800-535-4555 in Washington, DC (202) 720-3333, 10:00 am-4:00 pm EST

How To Tell If Meat Is Grilled Throughly

• Meat and poultry cooked on a grill often browns very fast on the outside. Use a meat thermometer to be sure food has reached a safe internal temperature, and cut into food to check for visual signs of doneness.

• NEVER partially grill meat or poultry and finish cooking later. Cook food completely to destroy harmful bacteria.

• When reheating takeout foods or fully cooked meats like hot dogs, grill to 165 F, or until steaming hot.

Storing Your Grill

• Clean cooking grate(s) and discard old briquets.

• Store in dry location.

• When LP tank is connected to grill, store outdoors in well-ventilated space and out of reach of children.

• Cover grill if stored outdoors. Choose from a variety of grill covers offered by Char-Broil.

• Store grill indoors ONLY if LP tank is turned off and disconnected, removed from grill and stored outdoors.

• When removing grill from storage follow “Cleaning Burner Assembly” instructions before starting grill.

23

Troubleshooting

Emergencies

Gas leaking from cracked/cut/burned hose.

Gas leaking from LP tank.

Gas leaking from LP tank valve.

Gas leaking between

LP tank and regulator connection.

Fire coming through control panel.

Possible Cause

• Old hose, cut in hose.

• Mechanical failure due to rusting or mishandling.

• Failure of tank valve from mishandling or mechanical failure.

• Improper installation, connection not tight, failure of rubber seal.

• Fire in burner tube section of burner due to partial blockage.

• Misalignment of valve to burner tube.

Grease fire or continuous excessive flames above cooking surface.

Problem

• Too much grease buildup in burner area.

Burner(s) will not light using ignitor.

(See Electronic Ignition

Troubleshooting also)

Continued on next page.

Possible Cause

GAS ISSUES:

• Trying to light wrong burner.

• Burner not engaged with control valve.

• Obstruction in burner.

• No gas flow.

• Vapor lock at coupling nut to LP tank.

• Coupling nut and LP tank valve not fully connected.

Prevention/Solution

• Turn off gas at LP tank or at source on natural gas systems. If hose is cut or cracked, replace valve/hose/regulator. If burned, discontinue use of product until a gas service technician/plumber has investigated cause and correction is made.

• Turn off LP tank valve.

• Call LP gas dealer 800-number on tank label or call local fire department.

• Remove regulator from tank and visually inspect rubber seal for damage. Reinstall and check for leaks. Ensure black knob is on tight.

• Turn off LP tank valve (if possible without injury to self). If fire cannot be controlled with baking soda/extinguisher, call local fire department. Remove burner and inspect for spider nest or rust.

Clean using bottle brush.

• Ensure valves and burner tubes are aligned per assembly instructions.

• Turn off LP tank valve. Leave lid open to allow flames to die down.

After cooling, clean food particles and excess grease from inside firebox area, grease cup/pan/tray, and other surfaces.

Prevention/Solution

• See instructions on control panel and in Use and Care manual.

• Make sure valves are positioned inside of burner tubes with clips attached (if featured).

• Ensure burner tubes are not obstructed with spider webs or other matter. See cleaning section of Use and Care manual.

• Make sure LP tank is not empty. If LP tank is not empty, refer to

“Sudden drop in gas flow.”

• Turn off knobs and disconnect coupling nut from LP tank.

Reconnect and retry.

• Turn the coupling nut approximately one-half to three-quarters additional turn until solid stop. Tighten by hand only - do not use tools.

ELECTRICAL ISSUES:

• Electrode cracked or broken; “sparks at crack.”

• Electrode tip not in proper position.

• Wire and/or electrode covered with cooking residue.

• Wires are loose or disconnected.

• Wires are shorting (sparking) between ignitor and electrode.

• Dead battery.

• Replace electrode(s).

Main Burners Traditional Series, QuickSet and QuickSet Series:

• Tip of electrode should be pointing toward tip of collector box . The distance should be 1/8” to 1/4”. Adjust if necessary.

Main Burners Performance and Advantage Series:

• Tip of electrode should be pointing toward port hole in burner. The distance should be 1/8” to 3/16”. Adjust if necessary.

Sideburner:

• Tip of electrode should be pointing toward gas port opening on burner. The distance should be 1/8” to 3/16”. Adjust if necessary.

• Clean wire and/or electrode with rubbing alcohol and clean swab.

• Reconnect wires or replace electrode/wire assembly.

• Replace ignitor wire.

• Replace with a new AAA-size alkaline battery.

24

Troubleshooting ( continued )

Problem

Burner(s) will not light using ignitor.

(See Electronic Ignition

Troubleshooting also)

Possible Cause

ELECTRONIC IGNITION:

• No spark, no ignition noise.

• No spark, some ignition noise.

• Sparks, but not at electrode or at full strength.

PIEZO PUSH-BUTTON AND ROTARY:

• Push-button sticks at bottom.

• Rotary knob rotates without clicking.

• Sparking between ignitor and electrode.

Prevention/Solution

• See Section I of Electronic Ignition System.

• See Section II of Electronic Ignition System.

• See Section III of Electronic Ignition System.

• Replace ignitor.

• Replace knob.

• Inspect wire insulation and proper connection. Replace wires if insulation is broken.

Burner(s) will not match light.

• See “GAS ISSUES:” on previous page.

• Match will not reach.

• Improper method of match-lighting.

• Use paper match, long-stem match (fireplace match) or match holder (where supplied).

• See “Match-Lighting” section of Use and Care manual.

Sudden drop in gas flow or low flame.

• Out of gas.

• Excess flow valve tripped.

Flames blow out.

• Vapor lock at coupling nut/LP tank connection.

• High or gusting winds.

• Low on LP gas.

• Excess flow valve tripped.

Flare-up.

• Grease buildup.

• Excessive fat in meat.

• Excessive cooking temperature.

Persistent grease fire.

• Grease trapped by food buildup around burner system.

• Check for gas in LP tank.

• Turn off knobs, wait 30 seconds and light grill. If flames are still low, turn off knobs and LP tank valve. Disconnect regulator. Reconnect regulator and leak-test. Turn on LP tank valve, wait 30 seconds and then light grill.

• Turn off knobs and LP tank valve. Disconnect coupling nut from tank. Reconnect and retry.

• Turn front of grill to face wind or increase flame height.

• Refill LP tank.

• Refer to “Sudden drop in gas flow” above.

• Clean burners and inside of grill/firebox.

• Trim fat from meat before grilling.

• Adjust (lower) temperature accordingly.

• Turn knobs to OFF. Turn gas off at LP tank. Leave lid in position and let fire burn out. After grill cools, remove and clean all parts.

Flashback...

(fire in burner tube(s)).

• Burner and/or burner tubes are blocked.

• Turn knobs to OFF. Clean burner and/or burner tubes. See burner cleaning section of Use and Care manual.

Unable to fill LP tank.

• Some dealers have older fill nozzles with worn threads.

• The worn nozzles don’t have enough “bite” to engage the valve. Try a second LP dealer.

One burner does not light from other burner(s).

• Grease buildup or food particles in end(s) of carryover tube(s).

• Clean carry-over tube(s) with wire brush.

25

Troubleshooting - Electronic Ignition

Problem (Ignition) Possible Cause

SECTION I

No sparks appear at any electrodes when ignition button is pushed; no noise can be heard from spark module.

• Battery not installed properly.

• Dead battery.

• Button assembly not installed properly.

• Faulty spark module.

Check Procedure Prevention/Solution

• Check battery orientation.

• Has battery been used previously?

• Check to ensure button assembly is fully engaged.

Button should travel up and down without binding.

• If no sparks are generated with new battery and good wire connections, module is faulty.

• Install battery (make sure that “–” and “+” connectors are oriented correctly, with “–” end up and “+” end down.)

• Replace battery with new AAA-size alkaline battery.

• Remove button cap assembly and reinstall, making sure it can be fully engaged.

• Replace spark module assembly.

SECTION II

No sparks appear at any electrodes when ignition switch is pushed; noise can be heard from spark module.

• Output lead connections not connected.

• Electrode tip not in proper position.

• Are output connections on and tight?

• Remove and reconnect all output connections at module and electrodes.

26

• Are the electrode tips pointing in the right direction? Is the gap too big?

Main Burners:

Traditional Series, QuickSet or QuickSet Traditional:

• Tip of electrode should be pointing toward tip of collector box. The distance should be 1/8” to 1/4”.

Adjust if necessary.

Performance and Advantage Series:

• Tip of electrode should be pointing toward port hole in burner. The distance should be 1/8” to 3/16”.

Adjust if necessary.

Sideburner:

• Tip of electrode should be pointing toward gas port opening on burner. The distance should be 1/8” to

3/16”. Adjust if necessary.

SECTION III

Sparks are present but not at all electrodes and/or not at full strength

• Output lead connections not connected.

• Arcing to grill away from burner(s).

• Are output connections on and tight?

• Remove and reconnect all output connections at module and electrodes.

• Weak battery.

• Electrodes are wet.

• Electrodes cracked or broken “sparks at crack”.

• If possible, observe grill in dark location. Operate ignition system and look for arcing between output wires and grill frame.

• All sparks present but weak or at slow rate.

• Has moisture accumulated on electrode and/or in burner ports?

• Inspect electrodes for cracks.

• If sparks are observed other than from burner(s), wire insulation may be damaged. Replace wires.

• Replace battery with a new AAA-size alkaline battery.

• Use paper towel to remove moisture.

• Replace cracked or broken electrodes.

Recipes by Chef Christopher Koetke, CEC, CCE

Five-Spice Grilled Duck Breast with Asian BBQ Sauce

4 boneless skinless duck breasts 1 garlic clove, minced

2 teas. finely grated orange zest 1-1/2 teas. five spice mix

Serves 4

1-1/2 teas. salt 1/4 teas. black pepper

Combine garlic, orange zest, five spice, salt and pepper with duck breasts. Let marinate in refrigerator for 4-24 hours. Grill duck breasts over high heat. Turn the breasts and liberally brush

0

Asian BBQ sauce on top. Grill until breasts are 150-155 internal temperature. While breast are cooking, grill green onions over high heat until they begin to soften (about 2 minutes). Serve with duck breasts. Additional Asian BBQ sauce (perhaps thinned with a little water) can be served on the side.

Asian BBQ Sauce Serves 3-4

2 Tbles. oyster sauce

1/4 teas. Tabasco

6 Tbles. hoisin sauce

2 Tbles. orange juice

1 teas. sesame oil

Mix ingredients together until blended. Store covered in refrigerator until needed.

Ratatouille Melts Serves 3-4

2 zucchini, diced (about 3 cups) 1 medium eggplant, diced (about 4 cups)

1 large red pepper, diced (about 1-1/2 cups) 1 large onion, finely diced (about 1-1/2 cups)

4 garlic cloves, minced

1/2 to 3/4 cup extra virgin olive oil

4 large tomatoes, seeded and diced

1-1/2 teas. salt

1/2 teas. black pepper

2 cups grated Mozzarella cheese

1 foot long French bread

1/3 cup Parmesan cheese

1/2 cup chopped fresh basil

In a large sauté pan, sauté zucchini over high heat in 2 Tbles. olive oil. Cook until zucchini are lightly browned and softened. Set aside in a bowl. Sauté eggplant over high heat in 3-4 Tbles.

olive oil until lightly browned and softened. Add to bowl. In the same sauté pan, sauté red pepper over moderate heat in 2 Tbles. olive oil. Cook until red peppers are lightly browned and softened.

Add to bowl. Sauté onions in 3 Tbles. olive oil until translucent, add garlic, cook 2 more minutes.

Add zucchini, eggplant and red pepper. Reduce heat and cook 15 minutes, or until all ingredients are very soft. Season with salt and pepper. (At this point, ratatouille can be chilled and reheated when necessary). Cut bread in half lengthwise. Scoop out center of bread so that it looks like a boat. Fill bread with hot ratatouille. Sprinkle with Basil, Parmesan and Mozzarella. Place filled breads over low heat. Cover grill and cook until cheese is melted and bread is toasted.

27

Char-Broil Turkey

Yield: 14 to 16 generous servings or 1 lb. per person

Cooking time: 25 minutes per pound • Method: Grill on low

12 to 14 lb. turkey, thawed completely

1 large apple, quartered vegetable oil

1 quart water

1-1/2 sticks butter

1 orange, quartered

1 lemon, thinly sliced or 4 tbs. lemon juice cheesecloth (optional)

2 stalks celery, cut in 2” pieces

2 onions, cut in large cubes salt and pepper

Heat grill to medium. Wash and rinse turkey, removing giblets. Dry with absorbent paper. Bend wings back behind turkey. Season inside of turkey with salt and pepper. Rub outside of bird with oil. Stuff with onions, celery, orange and apple. Completely fill cavity (this gives moisture to the turkey). Cover openings of turkey with excess skin. Melt butter in a large aluminum foil pan. Add turkey, water and lemon juice. Place on grill and turn heat to low. Baste with butter, cover top with cheesecloth and baste again. Baste every 1/2 hour until done. Serve with Giblet Gravy.

Giblet Gravy

2 to 3 turkey or chicken giblets

3-4 lbs. turkey or chicken fat salt and pepper to taste

1/4 teas. Accent

1/4 cup flour

2 cups fat-free pan juices

2 hard boiled eggs, finely chopped giblet broth, if needed dash of thyme

1/8 teas. Kitchen Bouquet milk, if needed

Boil giblets until tender, reserving broth. Chop giblets and set aside. Remove grilled turkey from baking pan and place on hot platter. Pour all pan juices into large measuring cup. Skim off fat, reserving 3 to 4 Tbles. Place reserved fat into a deep saucepan, heating over moderate heat.

Stir in flour, whisking well with wire whisk. Cook over low heat until bubbly then remove from heat.

Add fat free pan juices (add milk and giblet broth to juices to make 2 full cups). Blend well with wire whisk. Season with salt, pepper, Accent, thyme and Kitchen Bouquet, whisking continuously.

Return mixture to heat and continue stirring for 3 to 4 minutes. Add chopped eggs.

28

Smoked Turkey Breast

Cooking time: 25 minutes per pound • Method: Grill indirect heat

1 turkey breast, fresh or thawed 1 large bottle Italian dressing

1 large plastic roasting bag 1 small bottle soy sauce

Mix dressing and soy sauce. Place turkey breast in bag and pour mixture over turkey breast.

Marinate in refrigerator overnight. Light one side of grill with setting on low. Remove turkey from marinade and reserve liquid. Put meat thermometer in turkey breast being certain not to touch bone. Place turkey on the grill away from direct heat. Grill over low fire, basting and rotating often.

0 Remove when meat thermometer registers 180 F.

29

30

Please register your grill online at:

WWW.GRILLREGISTRATION.COM

(If you register online, you do not need to send in this registration card.)

Certified Grill Parts And Accessories®, Char-Broil and Design®, Char-Broil (Gas Grill Briquettes)®, Char-Diamonds®, Cooking Zone and Design®, Diamond

Flame®, Executive Chef®, Faststart®, Flare Fighter®, FlavorMaster®, Gas Grill Silouette and Design®, H2O Smoker®, Lava Flame®, MasterFlame®, MasterFlame

Precision Cooking System®, PowerSpark®, Quantum®, PrecisionFlame and Design®, Sierra® and TruFlame® are registered Trademarks of the W.C. Bradley

Company. Thermos® is a registered trademark of the Thermos Company and its affiliates.

Artisan Collectiion by Char-Broil™, C3 and Design™, Char-Broil and Design™, Flame Design™, FlavorTents™, Grill 2 Go™, Grillin’ Stick™, Keeper of the

Flame™, Keepers of the Flame™, Natural Grip™, Outdoor Cooking Collection and Design™, Patio Bistro™, PrecisionFlame™, Pro-Check™, QuickSet Grills and

Design™, SmokerTents™, The Big East™. The Minute Grill™, The Edge™, The Tuscan Collection™, and The Urban Grill™ are Trademarks of the W.C. Bradley

Company. Universal Grill Parts and Design™ is a trademark of the Thermos Company and its affiliates.

Protected under one or more of the following U.S. Patents: 4,598,692; 4,624,240; 4,747,391; 4,747,391; 4,817,583; 4,924,846; 4,989,579; 5,003,960; 5,076,256;

5,076,257; 5,090,398; 5,109,834; 5,224,676; 5,277,106; 5,421,319; 5,441,226; 5,452,707;5,458,309; 5,566,606; 5,579,755; 5,582,094; 5,613,486; 5,649,475;

5,706,797; 5,711,663; 5,765,543; 5,931,149; 5,996,573; 6,095,132; 6,135,104; 6,173,644; 6,279,566; 6,397,731; 6,418,923;6,439,222; 6,523,461; 6,792,936;

D282,619; D339,714; D341,292; D343,337; D358,059; D361,466; D364,535; D372,637; D373,701; D377,735; D383,035; D397,910; D405,643; D405,643; D406,005;

D406,009; D413,043; D413,229; D413,229; D414,982; D415,388; D416,164; D416,441; D417,587; D422,516; D423,274; D423,876; D428,303; D435,396; D463,004;

D438,059; D438,060; D438,427; D439,110; D442,505; D443,179; D443,354; D447,384; D447,385; D447,909; D448,610; D448,614; D448,615; D448,616; D448,975;

D449,492; D451,759; D456,202S; D460,313; D461,359 and D477,501. Canada: 87743; 87744; 92607; 92608 and 1,316,424. Other Patents Pending.©2004 W.C.

Bradley Co., All Rights Reserved.

31

32

ARRÊTEZ

1-800-387-6057

APRÈS-VENTE

q q q q q

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement