Chicago Electric 94882 Assembly and Operating Instructions

Add to my manuals
16 Pages

advertisement

Chicago Electric 94882 Assembly and Operating Instructions | Manualzz

BREAKER HAMMER

Model 94882

ASSEMBLY AND OPERATING INSTRUCTIONS

Diagrams within this manual may not be drawn proportionally.

Due to continuing improvements, actual product may differ slightly from the product described herein.

Distributed exclusively by Harbor Freight Tools ® .

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SaVe THiS manual.

Copyright © 2006 by Harbor Freight Tools ® . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

Electrical Requirement

Impactor Travel

Overall Dimensions

Blows per minute

Retainer Style

Retainer Capacity

Bit hardness

Bit Dimensions:

Noise Level

Impact Energy

Tool Weight

PRODUCT SPECIFICATIONS

120 Volt / 60 Hz / 16 Amps (running)

2-3/8”

25” L X 10-7/8” W X 9-3/8” H (hammer only)

1100 - 2100

Spring loaded rotational lock (2 positions only)

3/4” (19mm)

46-56 HRC

Chisel Bit: 3/4” Shank X 14-1/4” L

Bull Point Bit: 3/4” Shank X 1” W X 14-1/4” L

88 DBa @ 3 feet

3.7 to 18.4 Ft/Lbs.

33.75 Lbs.

NOTE: Plug this tool into a 20 Amp. dedicated circuit.

SAVE THIS MANUAL

You will need this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures, parts list and assembly diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.

SAVE THESE INSTRUCTIONS

WORK AREA

1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

REV 07e, 08b

SKU 94882 PAGE 2

2. Do not operate power tools in explosive atmospheres, such as in the presence

of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

3. Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed.

ELECTRICAL SAFETY

4. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly

grounded. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.

5. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in

any way. Double insulation eliminates the need for the three wire grounded power cord and grounded power supply system.

6. Avoid body contact with grounded surfaces such as pipes, radiators, ranges,

and refrigerators. There is an increased risk of electric shock if your body is grounded.

7. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

8. Do not abuse the Power Cord. Never use the Power Cord to carry the tools or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,

sharp edges, or moving parts. Replace damaged Power Cords immediately.

Damaged Power Cords increase the risk of electric shock.

9. When operating a power tool outside, use an outdoor extension cord marked

“W-A” or “W”. These extension cords are rated for outdoor use, and reduce the risk of electric shock.

PERSONAL SAFETY

10. Stay alert. Watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of

drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

SKU 94882 PAGE 3

11. Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.

12. Avoid accidental starting. Be sure the Power Switch is off before plugging

in. Carrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents. Make sure you are prepared to begin work before turning the Power Switch (62) “ON”.

13. Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury.

14. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the power tool in unexpected situations.

15. Always wear eye, hearing, and breathing protection. Wear ANSI-approved safety impact eye glasses, ANSI-approved hearing protectors, and ANSI- approved dust mask or respirator when using this product. Also, non-skid safety shoes and a hard hat must be used for appropriate conditions.

TOOL USE AND CARE

16. Do not use the power tool if the Power Switch does not turn it on or off. Any tool that cannot be controlled with the Power Switch is dangerous and must be replaced or repaired.

17. Disconnect the Power Cord Plug from the power source before making

any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally.

18. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.

19. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired.

20. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have

the tool serviced before using. Many accidents are caused by poorly maintained tools.

21. Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may become hazardous when used on another tool.

SKU 94882 PAGE 4

SERVICE

24. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury.

25. When servicing a tool, use only identical replacement parts. Follow instructions

in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.

GROUNDING

WARNING!

Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

1. Tools marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock.

(See Figure A, next page.)

2. The grounding prong in the plug is connected through the green wire inside the cord to the grounding system in the tool. The green wire in the cord must be the only wire connected to the tool’s grounding system and must never be attached to an electrically “live” terminal. (See Figure A.)

3. Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A page 6.)

SKU 94882 PAGE 5

FIGURE A

DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

4. Tools marked “Double Insulated” do not require grounding. They have a special

double insulation system which satisfies OSHA requirements and complies with

the applicable standards of Underwriters Laboratories, Inc., the Canadian

Standard Association, and the National Electrical Code. (See Figure B.)

5. Double insulated tools may be used in either of the 120 volt outlets shown in the

following illustration. (See Figure B.)

FIGURE B

SKU 94882 PAGE 6

EXTENSION CORDS

1. Grounded tools require a three wire extension cord. Double Insulated tools

can use either a two or three wire extension cord.

2. As the distance from the supply outlet increases, you must use a heavier gauge

extension cord. Using extension cords with inadequately sized wire causes a

serious drop in voltage, resulting in loss of power and possible tool damage.

(See Figure C)

3. The smaller the gauge number of the wire, the greater the capacity of the cord.

For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.

(See Figure C, and Figure D.)

4. If using more than one extension cord to make up the total length, make sure

each cord contains at least the minimum wire size required.

5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size.

(See Figure C, and Figure D.)

6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

7. Make sure your extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualified electrician before using it.

8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.

NAMEPLATE

AMPERES

(At Full Load)

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*

EXTENSION CORD LENGTH

0 - 2.0

2.1 - 3.4

25 Feet

18

18

18

50 Feet

18

18

18

75 Feet

18

18

16

100 Feet

18

16

14 3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

18

18

14

16

14

12

14

12

10

12

10

-

150 Feet

16

14

12

12

-

-

16.1 - 20.0

12 10 -

FIGURE C * Based on limiting the line voltage drop to five volts at 150% of the rated amperes.

SKU 94882 PAGE 7

SYMBOLOGY

Double Insulated

Canadian Standards

Association

Underwriters

Laboratories, Inc.

Volts Alternating Current no

V ~

A xxxx/min.

Amperes

No Load Revolutions per Minute (RPM)

SPECIFIC SAFETY RULES

1. Maintain labels and nameplates on the Breaker Hammer. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

2.

Industrial applications must follow OSHA requirements.

3. Check for damaged parts. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of this product. Replace or repair damaged or worn parts immediately.

4. Always disconnect the Breaker Hammer from its electrical outlet before

performing any services, maintenance, or cleaning such as leaving the work area, moving the tool from one location to another, changing Saw Blades, cleaning sawdust from the unit, etc.

5. WARNING! Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

(a) Lead from lead-based paints;

(b) Crystalline silica from bricks and cement or other masonry products;

(c) Arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals; work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety

Code 25249.5, et seq.)

SKU 94882 PAGE 8

6. WARNING! People with pacemakers should consult their physician(s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker.

WARNING: Always wear ANSI-approved impact safety goggles. Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI-approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. Always wear ear protection. Ear protection is required for any other persons in the work area.

WARNING: Be aware of flying concrete chips. Keep spectators clear of the work area.

WARNING: Do not operate this tool if you have back, neck, wrist, or other conditions or injuries that will be aggravated by the jerking forces this tool exerts upon its operator.

WARNING: Always use the side handle when operating this tool.

NOTE: Use the weight of the Breaker Hammer to break concrete. Use the tool in the vertical position whenever possible. This tool was intended to break larger pieces of concrete.

WARNING: If the Breaker Hammer ever gets out of your control, immediately release the

Switch (62).

1.

2.

VIBRATION HAzARD

This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury:

Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.

Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.

3.

4.

Wear suitable gloves to reduce the vibration effects on the user.

Use tools with the lowest vibration when there is a choice between different processes.

Include vibration-free periods each day of work.

5.

6. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately.

REV 07j

SKU 94882 PAGE 9

UNPACKING

When unpacking, check to make sure all parts shown on the Parts

Lists and Assembly Diagrams on pages 12-14 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible.

ASSEMBLY INSTRUCTIONS

How to attach and adjust the Side Handle:

1. Slide the Clamp (122) over the Collet (8). Secure it using the Knob (120). ( See

Figure 1 below.)

2. To adjust the angle of the Side Handle, loosen the Knob (120). Adjust the angle of the Side Handle, then tighten the Knob (120) to secure it.

Figure 1

122

8

Side Handle

120

SKU 94882 PAGE 10

How to attach the chisels

1. Slide the chisels into the Breaker Hammer with the flat cut-out side facing up and while the Rod (4) is aligned with the Chisel shank. See figure 2.

2. The Chisel has a flat space on the shaft that must be turned horizontally when it is inserted. See Figure 2. Pull out on the Pin and rotate it 90° to lock the Chisel in place. The Chisel should be able to move back and forth after it is locked but should not come out.

Lock Pin 4

Figure 2

Chisel

OPERATING INSTRUCTIONS

IMPORTANT - READ BEFORE USE

This Breaker Hammer may have decreased performance for a brief period at the beginning of each use. This warm-up period lasts approximately 3-5 minutes. This happens because the grease inside the tool may be thick, preventing the tool from operating at full efficiency while the motor is cold. This is normal and does not indicate a problem. To help reduce this effect, store this equipment in temperatures no lower than 50-60° F.

How to turn on the Breaker Hammer

To turn on the Breaker Hammer, flip the Switch (62) shown below in Figure 3.

How to Adjust the impact level of the Breaker Hammer

The Impact level is adjusted by turning the Knob (117). The numbers on the Knob indicate the level of impact. Number one is the lowest level, seven is the highest level. See Figure 4.

Figure 3 Figure 4

Knob (117)

Switch (62)

REV 12/06

SKU 94882 PAGE 11

OPERATING INSTRUCTIONS (CONTINUED)

Chipping in a straight line with a chisel bit

1. Use chalk or another suitable writing material and mark you work surface to delineate the area you intend to hammer.

2. Plug in the Breaker Hammer.

3. Grasp the main Handle (90) and side Handle (90) firmly with both hands. When you are sure that no people or animals are in the vicinity, and it’s safe to begin, depress the Switch (62).

4. The Breaker Hammer will begin to break the top layer of concrete. If you push down, it will begin to break the next layer as well.

5. Keep moving the Breaker Hammer along the line you want to section, breaking concrete as you go. If the Breaker Hammer jumps off of the line or section, release the Switch (62) and reposition the Breaker Hammer.

6. When you are finished, release the Switch (62) and unplug the Breaker Hammer.

Breaking up concrete with a bull point pit

1. Place the bit on the center of a piece of concrete.

2. Grasp the main Handle (90) and side Handle (90) firmly with both hands. When you are sure that no people or animals are in the vicinity, and it’s safe to begin, depress the Switch Knob (87).

3. As you break concrete into big chunks, release the Switch Knob (87) and move to other large pieces until all larger pieces are broken. Do not break up smaller pieces with this tool as it is too powerful and aggressive to control on small pieces.

4. When finished, release the Switch Knob (87) and unplug the Breaker Hammer.

INSPECTION, MAINTENANCE, AND CLEANING

1. WARNING! Always disconnect the Breaker Hammer from its electri- cal power supply source before performing any inspection, maintenance, or cleaning procedure.

2. Before each use, inspect the general condition of the Breaker Hammer. Inspect the switch, power plug and cord assembly, and extension cord (if used) for damage. Check for loose screws, misalignment, binding of moving parts and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, turn off the Breaker Hammer immediately and have the problem corrected before further use.

Do not use damaged equipment.

SKU 94882 PAGE 12

NO. PART NAME

1 Bushing

2 Pin

3 Ring

4 Pin

5 Screw M6X40

6 Washer

7 Spring Washer

8 Collet

9 O Ring

10 O Ring

11 O Ring

12 Spindle Cover

13 Seal

14 O Ring

15 Rear Bushing

16 Beat Piece

17 Bushing

18 Damper

19 Bushing

20 O Ring

21 Seal

22 O Ring

23 O Ring

24 Cylinder Sleeve

25 Ram

26 O Ring

27 Front Housing

28 Spring Guide

29 Spring

30 Spring Guide

31 Copper Guard

32 Spring guide

33 Screw M8X40

34 Washer

35 Spring Washer

36 Screw M4X14

37 Side Cover

38 Bearing 620NSK

39 Gear

40 Washer

41 Gear

SKU 94882

PARTS LIST

QTY NO. PART NAME

1

1

4

2

1

1

4

4

1

1

4

1

2

1

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

6

6

1

1

1

1

1

6

PAGE 13

42 Feather Key

43 Gear

44 Circlip

45 Bearing 6002NSK

46 Spacer

47 Spacer

48 Circlip

49 Seal

50 Bearing 620NSK

51 Circlip

52 Spring Washer

53 Washer

54 Screw M5X25

55 Cord Jacket

56 Cord

57 Capacitor

58 Seal

59 Cover

60 Screw ST4X18

61 Cord Clip

62 Switch

63 Actuator

64 Rod

65 Trigger

66 Pin

67 Brush Housing

68 Carbon Brush

69 Screw ST3X10

70 Brush Spring

71 Screw

72 Spring Washer

73 Washer

74 Fan Wheel

75 Cover

76 Screw ST3X10

77 Screw M5X25

78 Washer

79 Spring Washer

80 Brush Plate

81 Sleeve Insulator

QTY

4

1

4

4

1

1

1

1

1

1

2

2

2

2

1

1

1

1

1

1

1

2

1

1

1

6

1

6

6

1

1

1

1

1

1

1

2

2

1

1

REV 08b

NO. PART NAME

PARTS LIST CONTINUED

QTY NO. PART NAME QTY

82 Bearing 600NSK

83 Washer

84 Magnetism Ring

85 Rotor

86 Screw ST5X70

87 Stator

88 Housing

89 Glass Fiberpipe

90 Handle

91 Screw M5X18

92 Washer

93 Spring Washer

94 Screw M4X12

95 Cord Clip

96 Gear Case

97 O Ring

98 Bearing 6304NSK

99 Crank Shaft

100 Cover

101 Spring Washer

102 Washer

103 Screw M5X22

104 Needle bearing

1

1

1

1

1

6

6

1

1

6

2

1

1

1

1

1

1

3

3

1

1

3

1

105 Connecting Rod

106 Piston Pin

107 Pin

108 O Ring

109 Eletronic Board

110 Screw ST4X14

111 Connecting Plate

112 Cover

113 Spring Washer

114 Washer

115 Screw M5X25

116 Detent

117 Knob

118 Cover

119 Nut

120 Knob Seal

121 Handle

122 Clamp

123 Washer Clamp

124 Bolt M8X180

125 Pointed Chisel

126 Case 1

127 Square Chisel (not shown) 1

1

1

1

2

1

1

1

1

1

5

5

1

5

1

1

2

1

1

1

1

1

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED

THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.

NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REP-

RESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT

HE OR SHE IS qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT

OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANY PARTS OF THE

PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR

EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS

SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNI-

CIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND

LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL

PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF

HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

REV 08b

SKU 94882 PAGE 14

ASSEMBLY DIAGRAM

SKU 94882 PAGE 15

LIMITED 90 DAY WARRANTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL

OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

SKU 94882 PAGE 16

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement