Chief Manufacturing FSA-1004 User's Manual

INSTALLATION
INSTRUCTIONS
Small Flat Panel Lift Arm
FSA-1004 and KSA-1004
The Lift Arm FSA/KSA-1004 is an accessory that can be
used with a broad range of Small Flat Panel Displays.
The FSA/KSA-1004 allows the user to move a display
vertically up or down in a 13 inch radius. The lift arm can
be moved vertically 6-1/2” up from center and 6-1/2”
down from center.
Lift Arm
The FSA/KSA-1004 is designed to safely hold a display
weighing up to 25 lbs. (11.3kg). The display can be up to
30 inches wide.
The FSA/KSA-1004 accommodates all VESA®
75mm/100mm compliant displays.
BEFORE YOU BEGIN
CAUTION: To prevent damage to the mount, which could affect or void the Factory warranty, thoroughly
study all instructions and illustrations before you begin to install the mount brackets. Pay particular attention to the “Important Precautions” on Page 2.
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE. 700
SAVAGE, MINNESOTA 55378 USA
8832-000041 Rev. F
©2007 Chief Manufacturing
www.chiefmfg.com
03/07
Installation Instructions
FSA/KSA-1004
IMPORTANT WARNINGS and CAUTIONS!
WARNING
A WARNING alerts you to the possibility of serious injury or death if you do not follow
the instructions.
CAUTION
A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not
follow the corresponding instructions.
WARNING
Improper installation can result in serious personal injury! Make sure that the
mounting surface can support a redundant weight factor five times the total weight of
the equipment: if not, reinforce the mounting surface structural members before
installing the FSA/KSA-1004.
WARNING
Be aware of the potential for personal injury or damage to the unit if it is not
adequately mounted.
WARNING
The installer is responsible for verifying that the mounting surface to which the
FSA/KSA-1004 is anchored will safely support the combined load of all attached
components or other equipment.
WARNING
The combined weight of the display placed on the FSA/KSA-1004 must not exceed 25
lbs. (11.3kg), the maximum load capacity of the mount.
WARNING
Watch for pinch points. Do not put your fingers between movable parts.
WARNING
Make sure the mount is correctly oriented.
WARNING
When using an OFB and adding an additional arm to an existing mount, the total
number of arms on the mount cannot exceed two arms.
CAUTION
Check the unit for shipping damage before you begin the installation.
CAUTION
Over-tightening mounting screws may damage your display.
CONTENTS
TOOLS REQUIRED FOR
INSTALLATION
PARTS.......................................................................3
PARTS LIST ..............................................................3
5/32” Hex key wrench (provided)
INSTALLATION..........................................................4
Removing the Display from the Mount.....................4
3/16” Hex Key wrench (provided)
Installing the Lift Arm ..............................................5
Installing base end of lift arm ...............................5
NOTE: Other tools may be required depending on the
Installing display end of lift arm............................5
method of installation.
Adjusting Lateral Movement....................................6
Adjusting Lift Arm Tension ......................................6
Cable Management ................................................Error! Bookmark not defined.
2
Installation Instructions
FSA/KSA-1004
PARTS
Tension
adjustment bolt
50
70
70
30
10
70
30
70
50
20
40
80
20
60
Figure 1. Lift Arm Installation Drawing
PARTS LIST
Table 1. Lift Arm Parts
PART
DESCRIPTION
QTY
10
LIFT ARM
1
20
WASHER, UHMW , .640 ID X .845 OD
2
30
WASHER, UHMWPE, .318 ID X .031 OD
2
40
PIVOT PIN, SPF
1
50
CAPSCREW , BUTTON HEAD
2
60
LOCK NUT, NYLOCK
1
70
SPACER, STAINLESS STEEL, .320 X .018
4
80
LARGE LOCK NUT , NYLOCK
1
3
Installation Instructions
FSA/KSA-1004
INSTALLATION
Adding a lift arm modifies your mount configuration. This
procedure applies to most small flat panel displays,
particularly those with a pivot or swing arm, whether wall
mount or desk mount.
Removing the Display from the Mount
To remove the display from its mount, perform the
following steps:
NOTE: Do not remove the four screws (not shown) that
attach the display to the interface bracket.
1. Disconnect the power/audio/video cables from the
display (not shown).
2. Remove the cap screw, washers, pivot pin, and
retaining nut from the display end of the mount.
Refer to Figure 2. Separate the display from the
mount.
3. To remove the pivot pin (see Figure 2) from the other
end, do the following:
a. If the mount is a pivot/pitch wall mount, remove
the attaching hardware from the display.
b. If the mount is wall mounted, desk mounted, or
has more than one swing arm, remove the
attaching hardware from the arm closest to the
display.
NOTE: The two button head cap screws removed from
the mount will be replaced with longer screws
when the lift arm is installed.
NOTE: Keep the pivot pin removed in step 2. This part
will be used again when the lift arm is installed.
Cap screw
Small
Washer
Display Mount Parts — Typical
PART NAME
Pivot Pin
Flat Washers
Large
Washer
SCREW , CAP
2
WASHER, FLAT
4
SMALL WASHER, NYLON
2
LARGE WASHER, NYLON
2
NUT, NYLOCK
2
Nut
Figure 2. Single Swing Arm (FWS-110) — Example
4
QTY
Installation Instructions
FSA/KSA-1004
Installing display end of lift arm
Installing the Lift Arm
To install the lift arm, perform the following procedures:
Installing base end of lift arm
1. Locate the tension adjustment bolt on the lift arm
(see Figure 3). Install the pivot pin (40) and a washer
(20) onto the base of the mount.
2. Assemble a button head cap screw (50), one
stainless steel washer (70), washer (30), and a
second stainless steel washer (70) onto button head
cap screw (50) as shown in Figure 3.
3. Insert the screw assembly (step 2) into the pivot hole
on the lift arm (10) and the base end of the mount.
4. Thread the lock nut (60) to the screw assembly (step
2) at the bottom of the mount.
1. Install the original pivot pin (see Figure 3) that was
retained when the display was removed and a
washer (20) onto the base of the mount.
2. Assemble a button head cap screw (50), one
stainless steel washer (70), washer (30), and a
second stainless steel washer (70) onto button head
cap screw (50) as shown in Figure 3.
3. Insert the screw assembly (step 2) into the pivot hole
on the lift arm (10) and the display end of the mount.
4. Thread the lock nut (80) to the screw assembly (step
2) at the bottom of the mount.
CAUTION: Over-tightening a tension screw (50) will
cause excessive wear and may distort
adjustment components.
5. Using the 3/16” hex key (provided), tighten the
button head cap screw (50) into the nut (80) several
turns, leaving flexibility in the hinged joint. Do not
over-tighten the cap screw (50).
CAUTION: Over-tightening a tension screw (50) will
cause excessive wear and may distort
adjustment components.
5. Using the 3/16” hex key (provided), tighten the
button head cap screw (50) into the nut (60) several
turns, leaving flexibility in the hinged joint. Do not
over-tighten the cap screw (50).
Lift Arm Parts
ITEM
50
30
50
Original
Pivot
Pin
70
20
80
PART NAME
QTY
10
LIFT ARM
1
20
LARGE WASHER, NYLON
2
30
SMALL WASHER, NYLON
2
40
PIVOT PIN, SPF
1
50
CAP SCREW , BUTTON HEAD
2
60
LOCK NUT, NYLOCK
1
70
SPACER, STAINLESS STEEL
4
80
LARGE LOCK NUT , NYLOCK
1
40
10
20
60
Figure 3. Installing Lift Arm
5
Installation Instructions
FSA/KSA-1004
Lateral
Tension
Adjustment
Bolts
(Typical)
Adjusting Lateral Movement
CAUTION: Over-tightening tension bolt will cause
excessive wear and may distort adjustment
components.
To adjust the lateral movement tension, perform the
following procedures:
1. Slightly tighten or loosen the tension adjustment bolt.
2. Check for desired tension. Repeat as necessary.
Adjusting Lift Arm Tension
CAUTION: Over-tightening tension bolt will cause
excessive wear and may distort adjustment
components.
Adjusting Lateral Movement
To adjust the tension of the lift arm:
1. Raise or lower the lift arm until tension adjustment
bolt appears in the opening.
2. Using the 5/32” hex key (provided), adjust the
tension adjustment bolt, as follows:
Lift Arm Tension
Adjustment Bolt
NOTE: There is no fixed number of revolutions to turn
the tension adjustment bolt. Tighten or loosen
the bolt, as needed. When the bolt is adjusted
correctly, the display can be easily raised or
lowered at any time, and stay in place without
sagging.
a. To increase lift arm tension, turn the tension
adjustment bolt counterclockwise.
b. To decrease lift arm tension, turn the tension
adjustment bolt clockwise.
3. Raise or lower the lift arm to check for desired
tension. Repeat step 2 as needed.
6
Adjusting Lift Arm Tension
Installation Instructions
FSA/KSA-1004
7