advertisement
BV412RVB/SVB Guitar Enclosure
Your Crate BV412RVB/SVB 4x12 Guitar Cabinet is built from the finest materials and components available. The cabinet is carefully constructed from 13 ply Baltic Birch and covered with extremely tough Tolex ® . The cabinet is then loaded with four
Celestion Vintage 30 speakers.
The BV412RVB/SVB comes standard with casters, steel handles, a heavy duty metal grille for ultimate speaker protection, and a switchable, dual-impedance mono/stereo jackplate. The
BV412RVB features a straight baffle while the BV412SVB features a slanted top baffle.
The BV412RVB/SVB also comes with a 14 gauge speaker cable to help insure maximum power and full frequency response from your new cabinet.
For those wishing to use multiple cabinets, the BV412RVB has caster cups on its top surface to accomodate the casters of a second cabinet, stacked on top.
IMPORTANT SAFETY INSTRUCTIONS:
1.Read, follow and keep these instructions. Heed all warnings.
2.This speaker is capable of producing high sound pressure levels that may cause permanent hearing damage. User caution is advised and ear protection is recommended during use.
3.This speaker is designed for use on a sturdy, level surface. Whenever stacking speaker cabinets, do not stack more than two high. Only speaker cabinets which are equipped with caster cups on their top surfaces are to be used underneath a cabinet which is equipped with casters.
4.Speaker cables are a tripping hazard and must be routed out of traffic areas and away from any possible accidental contact.
5.Do not expose this speaker to rain or moisture. Do not place liquid filled containers on this speaker. Clean only with a damp cloth.
6.Repair or service of this speaker should be performed only by qualified personnel.
BV412RVB/SVB Guitar Enclosure
The Input/Output Plate:
(1) Impedance Selector Switch:
Use this switch to select 16 ohm mono operation or 8 ohm stereo/4 ohm mono operation.
(2) Out 1/4” Jack: When using the cabinet in the mono operating mode, use this jack to connect the cabinet to another speaker enclosure of the same impedance.
(3) In/Left 1/4” Jack: When using the cabinet in the mono operating mode, use this jack as the cabinet’s input jack. Connect the output of your amplifier to this jack by means of the 14 gauge speaker cable provided.
When using the cabinet in the stereo operating mode, connect this jack to the left channel output of your amplifier.
(4) Right 1/4” Jack: When using the cabinet in the stereo operating mode, connect this jack to the right channel output of your amplifier.
When using the cabinet in the mono operating mode, this jack is not used.
1 2
4 Ohm Mono Configuration:
OUT
16 OHM 4 OHM
16 OHMS
MONO
4 OHMS
MONO
OUT
8 OHMS
STEREO
IN
LEFT RIGHT
BV412RVB/SVB
Input plate
16 Ohm Mono Configuration:
OUT
16 OHM 4 OHM
3 4
Mono Amplifier
Mono Amplifier
16 OHMS
MONO
4 OHMS
MONO
8 OHMS
STEREO
OUT IN
LEFT RIGHT
BV412RVB/SVB
Input plate
8 Ohm Stereo Configuration:
LEFT OUT RIGHT OUT Stereo Amplifier
Refer to the illustrations to the right for additional information.
16 OHMS
MONO
4 OHMS
MONO
OUT
8 OHMS
STEREO
IN
LEFT RIGHT
BV215RVD
Input plate
BV412RVB/SVB Guitar Enclosure
Technical Specifications:
Impedance 4 or 16 ohms Mono, 8 ohms Stereo
RMS Power Rating
Peak Power Handling
Frequency Response
Sensitivity
Maximum SPL
Transducers
Full Range Inputs
Dimensions (H x W x D)
Weight
240 watts Mono, 120 watts Stereo
480 watts Mono, 240 watts Stereo
70Hz – 5kHz
100dB SPL 1 watt/1 meter
120dB
(4) Celestion 12” 16 ohm Vintage 30 speakers
(3) 1/4” jacks: Mono In/Out, Stereo Left and Right
31-1/2” x 30” x 14”
BV412SVB: 106 lbs; BV412RVB: 110 lbs
Specifications subject to change without notice.
www.crate.com
©2002 SLM Electronics, Inc. • A Division of St. Louis Music, Inc.
1400 Ferguson Avenue • St. Louis, MO 63133
47-633-04 • 121102
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project